Date post: | 27-Dec-2015 |
Category: |
Documents |
Upload: | lenard-mclaughlin |
View: | 214 times |
Download: | 0 times |
Linking & Guiding
Name that System!
How Stuff Works Under Pressure That’s So
Random!
10 10 10 10 10
20 20 20 20 20
30 30 30 30 30
40 40 40 40 40
50 50 50 50 50
Question 1 - 10
What acts as the guiding component for the chair in the picture below?
Answer 1 – 10
The guiding component is the black frame of the rowing machine, which guides the seat in a translational motion
Question 1 - 20
Describe the characteristics of the link between the broomball stick and the plastic bottom:
Answer 1 – 20
DIRECT INDIRECT
RIGID ELASTIC
REMOVABLE NON-REMOVABLE
COMPLETE PARTIAL
Question 1 - 30
What kind of guiding would be used to guide a garage door open?
Answer 1 – 30
Translational
Question 1 - 40
What type of guiding is pictured below?
Answer 1 – 40
Rotational
Question 1 - 50
What is the difference between a complete link and a direct link?
Answer 1 – 50
A complete link means that the two parts can’t move independently of each other (ie. if you move one part, the linked part moves too).
A direct link means that the two objects are attached directly, with nothing in between.
Question 2 - 10
What is the name of the system below and is it reversible?
Answer 2 – 10
Gear Train (motion transmission system)YES: it is reversible
Question 2 - 20
What kind of motion transformation is happening in this system? Is it reversible?
Answer 2 – 20
Slider-Crank Mechanism:rotational <-> translationalYES: it is reversible
Question 2 - 30
What is the name of the system? Is it motion transmission or transformation?
Answer 2 – 30
Worm and wheel – motion transmission
Question 2 - 40
Name the system below. Which component acts as the driver?
Answer 2 – 40
Cam and follower – motion transformationThe driver is the cam which rotates.
Question 2 - 50
What are the only two motion transformation systems that are
reversible?
Answer 2 – 50
Rack and Pinionrotational <-> translational
Slider-Crank rotational <-> translational
Question 3 - 10
Explain how you would tighten this clamp, and how it holds something in place:
Answer 3 – 10
When the handle is rotated, the screw is guided in a helical motion which closes and puts pressure on what it’s holding in place.
Question 3 - 20
Using the diagram below, explain how a windmill makes energy
Answer 3 – 20
The wind pushes the blades, which turns the shaft attached to the red gear. The red gear turns thesmaller gear, which is attached to a generator. The generator converts the wind energy to electrical energy
Question 3 - 30
What happens to theman when the red crank is turned?
Answer 3 – 30
When the red crank is turned, the cam will rotate, causing the follower to move up(translational motion), which then lifts the mans foot up and down.
Question 3 - 40
In the diagram below, explain how the wire controls the motion of the brake blocks:
Wire ->
Metal levers ->
Answer 3 – 40 When the wire is pulled up, the metal levers rotate around the screw and cause the brake blocks to close around the wheel rim
Wire ->
Question 3 - 50Explain how the drilling table is raised and lowered:
table
Answer 3 – 50
When the handle turns, the gear (pinion) rotates and moves up or down the rack. This causes the drilling table to move up or down, to match the height of the person using it.
Question 4 - 10
What is an example of tension?
Answer 4 – 10
Anything that involves the action of stretching out a material – ie. elastic band, tug of war etc.
Question 4 - 20
What constraint is the sponge under?
Answer 4 – 20
Torsion
Question 4 - 30
What constraint is a body builder under when holding a barbell overhead?
Answer 4 – 30
Compression
Question 4 - 40
Objects with this mechanical property can return to their original shape
when they undergo torsion, deflection, compression and tension.
Answer 4 – 40
Mechanical property = elasticity
(the ability to return to original shape after being subjected to a constraint)
Question 4 - 50
Name at least two constraints this buildingexperiences:
Answer 4 – 50 1. Deflection
2. Compression
Question 5 - 10
Which gear in the diagram below would go the fastest?
Answer 5 – 10
The yellow gear because it has the fewest teeth
Question 5 - 20
You need to build new hockey sticks for the Bears.
What are two properties you would look for when shopping for materials?
Answer 5 – 20
Hardness: ability to resist indentation
Resilience: ability to resist shocks without breaking
Stiffness: ability to retain shapes when subjected to constraints
Question 5 - 30
What is the name of the system below? Name two components that are rotating in the same direction.
Answer 5 – 30
Belt and pulley (motion transmission)
Question 5 - 40
How many times does the big gear turn if the small gear is turned 4 times?
Answer 5 – 40
Gear Ratio= 20/80 = 0.25
0.25 x 4 = 1
So if the small gear turns 4 times, the large gear turns 1 time.
Question 5 - 50
Would a ceramic or wood floor be better in a bathroom if you wanted the floor to
last for a long time?
Answer 5 – 50
Ceramic tile would be better because the moisture from the water in the bathroom could break down wooden floors over time.