LIST OF EQUIPMENT REQUIRED FOR NDT SERVICES Method: - MAGNETIC PARTICLE TESTING (MPT)

S.NoEquipment NameManufacturerModelQuantity

1

i) Magnaflux Y7AC/DC Yoke kitii) PARKER RESEARCH CONTOUR PROBEiii) sims AC\HWDC YOKE HWDC for subsurface flaw detection Handy Light Weight Safe for operator Lifting capacity 27 kgs in DC, 5 kgs in AC mode. Portable MPI Units

The portable MPI units offered by us are intricately designed for continuous operation and efficiently yields accurate results. Based on latest technology, our units are available in various models.

Some of the technical specifications of our range encompass of the following:

Specifications of portable MPI units: Models available: 1000, 1500 & 2000 Amps rating Current outputs: AC and HWDC Heavy duty cycle: 2 min. ON & 2 min. Off Auto AC Decay Demagnetization Facility Input Voltage: 230 V / 415 V Thyristorise step less solid-state control

Our immense industrial expertise and sophisticated machinery aid us in manufacturing and exporting an exclusive array of magnetic particle testing accessories. These are stringently checked by our team of quality controllers and are available in customized ranges. Below Mention All magnetic particle testing (NDT) accessories.

Our range of magnetic particles accessories bears the following varieties: Pie Gauge/ Field Indicator: To establish adequacy and direction of Magnetic Field Ketos Test Ring: To Evaluating sensitivity of Magnetic particles (as per ASTM E-1444 standards) Yoke Test Bar: To find out surface and sub-surface defects with Yoke (As per ASTM standards) MPI Powders: Dry & Wet methods MPI Powders Gauss Meter/ Residual Fields Indicator: To Indicate Residual Magnetism in the job UV light low intensity & high intensity black light Puffer Bulb: To apply Dry Method powders on job surface UV Meter/ Lux Meter: To Measure UV Bulb & White Light Intensity

Send Enquiry

Magnaflux

Parker DA-200

SIMS(Part #43560)

Parker DA-200

AC\HWDC1

2i)Magnavis Y-8 230VDC Battery PoweredYoke Kit

ii) YOKE: MEY- 3

Magnaflux611710-01:Y-8 Yoke Kit- 230V1

3PIE GAUGENAASTM Sec-V, SE 709 / A-2752

4STANDARD LOAD TEST PLATE FOR YOKES:NAWeight4.5 Kgs,18.2Kgs1

5RESIDUAL FIELD INDICATOR:NANA1

6Yoke Test BarNACalibrationblock forpenetratio n with (6Holes)1

7i)Magnavis Test Kit Black Iron Oxide, Water Base(Visible)i)Magnaflux

ii)crack checkiii) Ferro check45295

(visible)

1

8i) Magnavis WCP-2Contrast Paint(visible)i)Magnafluxii)crack checkiii) Ferro checkBS 5044(visible)

10

9i) Magnavis 7C Black Visible Wet Method Dry Powder Concentrate(visible)i)Magnaflux ii)CRACK CHECK iii) Ferro check01-1116-66:8 lb. Jar(visible)

1

Method: - LIQUID PENETRATING TESTING(LPT)S.NoEquipment NameManufacturerModelQuantity

1i) Spotcheck SK-816Penetrant InspectionKit ii) PMC Flaw check kit

i)Magnaflux

ii) PMC Flaw Check

i)SpotcheckSK-416

(visible)4

2i) Spotcheck SK-816Penetrant ins Kit

ii) Crack check ins kiti)Magnafluxii)Crack check i)SpotcheckSK-416ii) crack check kit(visible)4

Method: - ULTRASONIC TESTING (UT)

Sr.

No.

Description Qty.

Nos.

1. 1i)krautkramer usm 35 kit

The latest version of the USM 35 portable ultrasonic flaw detector from GE's Inspection Technologies business, is now totally protected against the ingress of dust and high pressure jets of water to IP 66 and contains new software which allows its operation to Japanese weld inspectionstandards.

ii) DIGISCAN DS-322 kit

iii) MODOSONIC Einstein II TFT kit

2V1 - Reference Block, IIW type, including wooden box with Handle1

3V2 - Miniature Block including wooden box. 1

4 CALIBRARTION BLOCK (STEP WEDGE)1

5COUPLANT1

MB4S- 10mm Diameter & 4 MHz577492

Cable for the above straight beam probes:MPKL2 Probe Cable 2m504862

0 TR-Straight Beam Probes (Very good near resolution)

MSEB4- 3.50x10 mm Diameter & 4 MHz574622

Cable for the above TR probesSEKG 2 TR Probe cable 2m538872

Angel Beam Probes (Small case, narrow sound field at small to middle depth

MWB45-4 8x9mm Diameter & 4MHz&2 MHZ569271

MWB60-4 8x9mm Diameter & 4MHz&2MHZ569281

MWB70-4 8x9mm Diameter & 4MHz&2MHZ569291

Cable for the above angle beam probes:MPKL2- Angel beam probe cable 2m504862

MWB45-2591081

MWB60-21

MWB70-21

MB2S- 10mm Diameter & 2MHz1

MB2S-24MM1

FEATURES & SPECIFICATIONS&AVAILABILITY OFMAGNETIC PARTICLE TESTING EQUIPMENT

1 ) Magnaflux Y7 AC/DC Yoke

Magnaflux Y7 AC/DC YokePortable lightweight yokes for one-person inspection in tight placesAdjustable legs enable you to inspect many different surface configurationsOne year warrantyYoke:230v, 50/60 Hz (Part #43560)

Current Draw:9 amps @ 115v AC4 amps @ 115v DC4 amps @ 230v

Demag:Yes

Yoke Weight:7.2 lbs 220v (3.27 kg)

Leg Capacity:0-30cm (0-12") across poles

Cord:12 ft (365.8 cm) with grounded plug

Other:Carrying case and instructions

Articulating, double-jointed legs contour easily to any part shape to assure good contact.Pull force (60 lbs DC, 10 lbs AC) complies with specifications.Solid state controls located in housing for maximum safety and reliability.2-minute ON/OFF duty cycles for fast, efficient inspections.

Reference web : http://www.rfsales.com.au/mpi_dp/sub_category/index.php?ID=Magnetsii) PARKER RESEARCH CONTOUR PROBE HAND HELD MAGNETIC PARTICLE YOKES

The DA-200 Contour Probe is a portable, self-contained instrument designed to produce a magnetic field on or within ferro-magnetic materials. It features built-in selective AC and pulsed DC functions, articulating legs and a rugged, molded housing making it ideal for use in the lab, on the factory floor or out in the field.Specifications:Mechanical Capacity: Distance across poles: 0 to 18".Fields (Selective): AC: Constant level, 20 pound pull. DC: Pulsed, 90 pound pull.Power Source: 105-125 VAC, 50-60 Hz, 4 Amps. Includes 8' 3-conductor power cord and plug. (Available in export voltages.)Controls: Momentary, push to test. AC/DC pulse selector switch.Contour Probe Kit A: Steel carrying case with handle and latch,1 lb. each of Red and Gray inspection powder in plastic bottles, PB-1 Hand Powder Blower and instructions.Contour Probe Kit A/B: Same as Kit A plus EA140 hand-held UV light, one 778A (9.5 oz.) aerosol can fluorescent particles. REF WEB : http://www.tedndt.com/cat/cat50_Parker.php

iii) SIMS Magnetic Particle Inspection Yoke MPI KIT

Meticulously designed, our dual magnetization yoke and portable MPI unit (AC / HWDC Yoke) and MPI Portable Unit are high in performance and are easy to operate. With strong and rugged construction, these are suitable for continuous operation.

Following are some of unique features of dual magnetization yoke:

Kit Part Number 611710: Y-8 Yoke Kit - 115V 611710-01: Y-8 Yoke Kit - 230VKit Includes: Battery Powered Yoke, Charger, Battery Pack with Shoulder Strap, #1 Grey Powder, Powder Spray Bulb, Paint Marker, ScrubsHand Cleaner, and Instructions.Other Part Numbers 620145: Y-8 Yoke (no charger) 620142: Y-8 Yoke with 115V Charger (ONLY) 620709: Y-8 Yoke with 230V Charger (ONLY)General SpecificationsY-8 Yoke

Weight7.75 lbs

Leg Span0" - 12"0 - 30.5 cm

Yoke Curent Draw4 Amps @ 6 Volts

Battery Charger Current Draw0.2 Amps @ 115V or 230V

Cord Length12 feet

Warranty1 year

Battery Charger Specifications 6 Volt, 12 Amp Hour 5.25 lbs. 4.25" x 2.75" x 5.5" Output Voltage Charge 6.84V or 7.35V Battery Output Current 1.6 Amps Maximum Battery Operating Temp. Range-40C to 60 C(-40 F - 140 F)

Reference web : http://www.rfsales.com.au/mpi_dp/sub_category/index.php?ID=Magnets2-i) MagnavisY-8 230V DC Battery Powered Yoke KitThe MagnavisY-8 Battery Operated Magnetic Yoke brings battery portability to magnetic particle yoke testing. 100% portable for field inspections Battery pack with convenient shoulder strap Articulating, double-jointed legs contour to part's shape for superior contact Solid state controls located in the yoke's housing for maximum safety and reliability

ii)

C] YOKE: MEY- 3

Model : MEY 3Magnetising Flux : AC / HW DC / FW DCInput Power : 110 /230 VWeight : 2.800 Kgs.REF WEB : http://www.3endt.com/magnetic_particle_testing_equipment.htm

3) FIELD INDICATORS(Pie Gauge) :

Ref web : http://www.3endt.com/magnetic_particle_testing_accessories.htm4] STANDARDLOAD TEST PLATE FOR YOKES:

Load Test Plate for checking the lifting power of Yoke Type Crack Detector Load Test Plate Weight 4.54 Kgs ( 10 Lbs.) for checking lifting power of YOKE in AC mode Load Test Plate Weight 18.18 Kgs ( 40 lbs.) for checking lifting power of YOKE in DC modeRef web : http://www.3endt.com/magnetic_particle_testing_accessories.htm5)RESIDUAL FIELD INDICATOR:Magnetic Field Strength Indicator[ME Field Indicator]Field Indicators 10-0-10 (Uncalibrated)10-0-10, 20-0-20, 50-0-50 (Calibrated with certificate)

Ref web : http://www.3endt.com/magnetic_particle_testing_accessories.htm

6) Yoke Test Bar

Top of FormRefWeb: http://www.radentndt.com/magnetic-particle-inspectionTest Piece for checking longitudinal field of Yoke Type Crack Detector Test bar of rectangular cross section with holes drilled in the transverse direction to depth of 1 mm, 2 mm, 3.0 mm, 4 mm, 5.0 mm , 6.0mm and 7.0 mm from top surface Suitable to evaluate the function of Yoke Type Crack detector to detect near surface and subsurface defects

7)MagnavisNon- FluorescentTest KitMagnavisNon-Fluorescent Test Kits come with all materials (Yoke not included) required to perform in-field or in-shop non-fluorescent NDT inspections.Each MagnavisNon-Fluorescent Test Kit Includes: 1 lb. of #1 Gray, 1 lb. of #8A Red, and 1 lb. of #3A Black Powder. Two (2) cans of (16 oz.) 7HF, One (1) can of WCP-2 Contrast Paint, Two (2) cans of SKC-S Cleaner / Remover, Powder Spray Bulb (P/N 501232), Field Indicator (P/N 2480), Paint Marker, SCRUBS Hand Cleaner and Instructions.Ref web :-Part Number and Container Size: 45295Applications:Portable Non-Fluorescent NDTinspections.

Bottom of Formhttp://www.magnaflux.com/Products/MagneticParticleInspection/MagnavisVisible/NonFluorescentVisibleInspectionKits/MagnavisVisibleInspectionKit.aspx8) MagnavisWCP-2 Contrast PaintMagnavisWCP-2 Contrast Paint provides a white background that enhances magnetic particle indications.MagnavisWCP-2 is composed of acetone and inorganic pigments and utilizes a carbon dioxide aerosol propellant for ease of application.Specifications Compliance:BS 5044Part Number and ContainerSize: 01-2250-79: 16 oz. Aerosol (9) - Sold in the USA only 01-2250-78: 16 oz. Aerosol (12)

Ref Web: http://www.magnaflux.com/Products/MagneticParticleInspection/MagnavisVisible/NonFluorescentVisibleInspectionKits/MagnavisVisibleInspectionKit.aspx

9 ) Magnavis7C Black Visible Wet Method Dry Powder ConcentrateMagnavis7C Black Visible Wet Method Dry Powder Concentrate is ideally suited for use on light colored surfaces where optimum color contrast is needed.Magnavis7C is composed of compounded magnetic powder and may be suspended in either Carrier II Oil Vehicle or in water.Specifications Compliance:ASME B & PV Code, Sec. V, ASTM E 709 (E-138), ASTM E 1444, AMS 3042, MIL-STD-271, MIL-STD-2132, NAVSEA 250-1500-1Part Number and Container Size: 01-1116-66: 8 lb. JarApplications:Magnavis7C Black Visible Wet Method Dry Powder Concentrate is used to locate inclusions, seams, shrink cracks, tears, laps, flakes, welding defects, grinding cracks, quenching cracks and fatigue cracks.http://www.magnaflux.com/Products/MagneticParticleInspection/MagnavisVisible/NonFluorescentVisibleInspectionKits/MagnavisVisibleInspectionKit.aspx

FEATURES & SPECIFICATIONS&AVAILABILITY OFLIQUID PENETRATING TESTING EQUIPMENT1- i SpotcheckSK-416 Penetrant Inspection Kit

Specifications Compliance:AMS-2644, AECL, ASME B & PV Code Sec V, ASTM E1417, MIL-STD 2132, ASTM E165, MIL-STD 271Kit Description/Contents:Spotcheck SK-416 Inspection Kits Contain: (1) Can of SKL-SP2 Penetrant, (2) Cans of SKC-S, and (1) Can of SKD-S2 Developer in a handy portable carrying case.Part Number:01-5970-48Applications:Automobile Parts, Off-Road Equipment, Farm Equipment, Welds, Castings, Forgings, Leak Testing, Pressure Vessels, Aircraft, Marine, Construction, Maintenance, Petroleum Pipelines, Power Plant Inspections, General Metalwork.

ii) PMC FLAW CHECKNext >>

Product Specification

DYE Penetrant MaterialWe are offering a quality range of dye penetration material that is provided with companytest certificate of dye penetrate testing material. Being an authorized dealer of P-met Company, based at Baroda, Gujarat; our complete range of dye penetration material is approved bythird party agenciesand government companies. This penetration material is available in all grade dye penetration material as per the requirement.These are available in the following quantities:

Ref web : http://www.magnaflux.com/Products/PenetrantInspection/SpotcheckVisible/SpotcheckKits/SK416Kit.aspx2-i SpotcheckSK-816 Penetrant Inspection Kit-

Specifications Compliance:AMS-2644, AECL, ASME B & PV Code Sec V, ASTM E1417, MIL-STD 2132, ASTM E165, MIL-STD 271Kit Description/Contents:SpotcheckSK-816 Kits Contain: (2) Cans of SKL-SP2 Penetrant, (4) Cans of SKC-S , and (2) Cans of SKD-S2 Developer in a handy portable carrying case.Part Number:01-5920-48Applications:Automobile Parts, Off-Road Equipment, Farm Equipment, Welds, Castings, Forgings, Leak Testing, Pressure Vessels/Aircraft, Maintenance, Marine, Construction, Maintenance, Petroleum Pipelines,

Ref web : http://www.magnaflux.com/Products/PenetrantInspection/SpotcheckVisible/SpotcheckKits/SK416Kit.aspx

ii) CRACK CHECK

Top of FormBottom of Form

Product DescriptionWe have earned appreciation in the markets for providing to the customersRed Dye Penetrant. Red Dye Penetrant is widely used for surface crack detection. Based on its unmatched quality, clients have been turning back to us for orders of Red Dye Penetrant. We manufacture the Red Dye Penetrant from finest quality raw material, which is sourced from the reliable vendors of the market. Clients can avail the Red Dye Penetrant

Specialty

Water Washable Solvent RemovableREF WEB : http://www.ferrochemndtsystems.com/red-dye-penetrant.ht

FEATURES & SPECIFICATIONS&AVAILABILITY OFULTRASONIC TESTING EQUIPMENT1 ) USM 35X

The latest version of the USM 35 portable ultrasonic flaw detector from GE's Inspection Technologies business, is now totally protected against the ingress of dust and high pressure jets of water to IP 66 and contains new software which allows its operation to Japaneseweld inspectionstandards.

Calibration rangesMin0 to 0.5 mm +10 % (steel), 0 to 0.02 +10 % (steel)

Max0 to 9,999 mm +10 % (steel), 0 to 390 +10 % (steel) within the frequency range from 0.2 to 1 MHz / 0.5 to 4 MHz 0 to 1,420 mm +10% (steel),0 to 56 +10 % (steel) within the frequency range from 0.8 to 8 MHz / 2 to 20 MHz

Sound velocity1,000 to 15,000 m/s, 40 to 600 inch/ms variable in steps of 1 m/s, 0.1 inch/ms and fixed programmed values

Display delayFrom -10 to 1,000 mm, -0.3 to 40 (340 s)

Probe delay0 to 200 s

Auto calibrationMeasurement and setting of sound velocity and probe delay using two known calibration echoes (2-point calibration)

Pulse intensity220 pF, 1 Nf

Damping50 ohms, 500 ohms (1,000 ohms in TR mode)

Pulse repetition frequency4 to 1,000 Hz, variable in 10 steps

Frequency ranges (-3 dB)0.2 to 1 MHz / 0.5 to 4 MHz / 0.8 to 8 MHz / 2 to 20 MHz

Gain0 to 110 dB, variable in steps

Gain steps0.5 / 1 / 2 / 6 / 12 dB (or user-adjustable), step 0 is locked

Fine gain4 dB, continuously variable in 40 steps

RectificationFull-wave, negative and positive half-wave, RF mode

RejectLinear, 0 to 80 % screen height Variable in steps of 1 %

Monitor gates2 independent gates in color bar mode, start and width variable over the entire calibration range, response threshold of 10 to 90 % screen height variable in steps of 1 % (coincidence and anti-coincidence), alarm signal via LED and connectable internal horn, Gate A switchable as interface gate for Gate B, gate magnifier (zooming of gate range over the entire display range)

Sound path measurementDigital display of sound path (projection distance, depth) between initial pulse and the first echo in the gate, or between the echoes in the two gates, measurement always at the intersection point with the echo flank or echo peak

Measurement resolution0.01 mm within a range up to 99.99 mm/ 0.1 mm within a range from 100 to 999.9 mm/ 1 mm above 1,000 mm, 0.001 within a range up to 9.999/ 0.01 above 10 With evaluation in the frozen A-scan: 0.5 % of the calibration range setting

Amplitude displayIn % screen heightUSM 35X DAC: additionally in dB above DAC or TCGUSM 35X S: additionally in dB above DGS curve or ERS

Displayed readingSound path, (reduced) projection distance, depth, amplitude for every gate, userconfigurable at four positions of measurement line and of the zoomed display in the A-scan

A-scan functionsManual or automatic A-scan freeze, A-scan comparison, echo dynamics (envelope), peak echo storage

Color functionsPatented color-coded display of legs in angle testing, adaptation of background color to the light conditions of test environment, color display of monitor gates and of registration curves (DAC, TCG, DGS) for direct recognition, messages and alarms in red characters

DAC / TCG (Option)Only USM 35X DAC and USM 35X S: Distance- Amplitude Curves (DAC) or TCG line (TCG) with a maximum of 10 reference echoes, 4 other curves or lines can be displayed with variable dB intervals. JIS DAC can be selected in order to allow inspection acording to JIS Z3060-2002 (Japanese Inspection Standard). Automatic gain control during DAC recording.

DGS (Option)Only USM 35X S: DGS curves for single-element and dual-element probes (B1S, B2S, B4S, MB2S, MB4S, MB5S, WB-1, WB-2, SWB-2, SWB-5, MWB-2, MWB-4, SEB and MSEB) and for all materials, sound attenuation and transfer loss correction, 4 other curves can be displayed with variable dB intervals

Display size / resolution116 mm x 87 mm, 4.6" x 3.4" (W x H)320 x 240 pixels

A-scan size / resolution116 mm x 80 mm, 4.6 x 3.2320 x 220 pixels (zoom)

Units of measurementmm, inch

Data memory800 instrument setups or reports, including AScans can be stored, recalled, printed or exported to a computer.

Direct documentationDisplay screen contents, report including A-scan, reading, function list (parameter dump)

Printer driverHP DeskJet, HP LaserJet, HP DJ 1200 (DeskJet),HP LJ 1012 (LaserJet), EPSON FX/LX, SEIKO DPU

RS 232 interface9-pin DSUB, bi-directional, 300 - 57,600 baud An USB adapator cable can be provided to connect the USM 35X to a computer that does not have RS 232 port

Input/Output8-way Lemo-1 socket (trigger output, gate alarm, test data release)Additional analog output for amplitude or sound path in selected gate

VGA output10-way Lemo-1 socket for the connection of an external display screen or beamer

Probe connections2 x Lemo 1 or BNC

Dialog languagesGerman, English, French, Italian, Portuguese, Spanish, Danish, Swedish, Norwegian, Finnish, Czech, Slovenian, Romanian, Dutch, Croatian, Hungarian, Russian, Polish, Slovakian, Japanese

Battery operationLi-ion battery or 6 C-cells (NiCad, NiMH or AlMn), operating time: 14 hours with Li-ion battery (6.6 Ah), approx. 3 hours with NiMH cells (3 Ah), battery charge check by an icon in the measurement line

Power pack/ battery charger operationVia an external power supply (85 to 265 VAC);Operating voltage: 6 to 12 VDCCurrent consumption: max. 9 W, depending on the setting

Weight2.2 kg, 4.9 lbs., including batteries

Size177 mm x 255 mm x 100 mm, 7.0" x 10" x 3.9" (H x W x D)

EnvironmentalProtection class: IP 66 Shock proof acc. to DIN IEC 68: 6 ms, 60 g, 3 shocks per orientation Vibration proof acc.to DIN IEC 68: 0 - 150 Hz, 2 g, 20 cycles per orientationOperating temperature: 0 to 60C; 32 to 140F (-10C; 14F on special request)Storage temperature: -20 to 60C; 4 to 140F

Data Logger OptionMemory capacity5,000 readings, 500 A-scans for the readings, 100 jobs, 10 comment texts per job

Storable readingsSound paths and sound path differences of all gates, amplitudes (% SH, dB-to-threshold, dBto-curve, %-to-curve, ERS), alarms of all gates or tolerance monitor

Lines / columnsNumber of lines: maximum 5,000 (Linear file with one column), numerical indexing Number of columns: maximum 26, indexing: A, , Z

Tolerance monitorLower and upper acceptance level with monitor function

Minimum reading captureStorage of the minimum value measured in continuous scanning, display of the value 3 seconds after uncoupling the probe

Monitor gate1 additional independent gate in color bar mode

ii) DIGISCAN DS-322AUTHOR:BLOGGERS| POSTED AT: 2:57 AM |FILED UNDER:DIGISCAN DS-322,FLAW DETECTORS

Touch Weather protected industrial housing Easy to use direct access to all function Small compact size, light weight Colour TFT display with excellent visibility Fast update rate High speed digitiser Parabolic DAC curves Reference echo pattern at background Echo fill/unfill option for better visibility Through coating thickness measurement Auto / Selectable PRF Surface mount micro component technology Direct interface to printer EECOWIN software for PC connectivity AffordableTop of FormBottom of Form

REF WEB : http://suppliers.jimtrade.com/148/147878/digiscan__model_ds322_311.htm

iii)Einstein II TFT :

Salient Features Very handy and light in weight (only 2.3 kgs with battery) TFT(Colour LCD) provides wide viewing angle and allows fast scanning speed. Very long battery operation of 8 hours between charges Digital plotting of DAC curves with automatic -6dB and -14dB curves Very low noise level even at very high gainTECHNICAL SPECIFICATION

Test Range10mm to 5 meter (in steel) adjustable in 1mm or 10mm step

Velocity1000 m/s to 9999 m/s adjustable in 1 m/s or 10 m/s step. Direct velocity setting for longitudinal and shear waves for steel.

DelayUp to 3 meter adjustable in 0.5mm or 5mm step

Gain100 dB calibrated gain adjustable in 0.5, 1, 2, 6, 12 or 20 dB step.

Rejection0 to 100% FSH with LED indicator

RectificationFullwave rectified with filtering.

Frequency0.5 MHz to 15 MHz (Wideband)

Test ModesPulse echo and transmit/receive.

ConnectorsBNC and LEMO(Size 1) both are provided

MonitorDual gate adjustable in1%of Screen width with Positive/Negative logic, Gate Expand modes

Gate ExpandExpands Range to width of the gate

A-Scan memory200 Trace Patterns can be stored, recalled, printed or transferred to PC via RS-232 serial port.

Calibration Set-up50 different calibration set-ups can be Stored and Recalled

SoftwareEinSoft Interface software for transferring A-Scan from Einstein- II TFT to PC is supplied

Printer AttachmentAny PC Printer with serial port can be attached for instant print-out of Trace Pattern (A-Scan with Set-up data).

Display122x92 mm (320x240 pixel) Colour LCD/TFT display for better visibility with option of eleven different colour sets.

Full ScreenBy pressing Zoom key A-Scan can be displayed in Full Screen area.

Reference A-ScanReference A-Scan pattern of standard test object can be saved and recalled in the background for easy comparision during testing.

DACDAC curve can be Digitally plotted on screen with -6dB and -14dB DAC curves. DAC curve can be set as flaw monitor gate with -6dB and -14dB DAC curves.

Digital ReadoutAnd Trig. FunctionThickness/Depth can be displayed in digital readout when using a normal probe and Beam path, Surface Distance and Depth are directly displayed when angle probe is in use.

Update Rate50Hz

PowerLithium-Ion Battery pack 14.4VDC, 4AH, gives 8 hours continuous operation from fully charged battery.

ChargerInput Voltage 100 to 240 VAC. Charge status indicator is provided.

Temperature :0 to 55 C

Size152 x 255 x 70mm (HxWxD).

Weight2.3 Kgs. with Battery.

Ultrasonic V1 & V2 Calibration Blocks

NDTE Enterprises Manufacture Ultrasonic Calibration Block V1 & Calibration Block V2.2 )Calibration Block V1A steel block for the calibration of ultrasonic flaw detection and inspection equipment used in material testing. Used for the calibration of shear and longitudinal transducers, determination of shear wave emission point, refracted angle. Also for measurement of sensitivity and resolution.3)Calibration Block V2For the ultrasonic examination of welds. To check angle transducers for beam angle and index point. Available in 12.5mm and 20mm thickness

4) UT Step Block

Certified Step Wedges for Ultrasonic Thickness Testing. Calibrationstep wedges are available inStainless Steel, Carbon Steel or Aluminium.

1) Step wedge block- 5 mm to 25mm (5 step)

2)Step wedge block- 1 mm to 10mm (10 step)

3)Step wedge block- 2 mm to 20mm (10 step)

step wedge available in any other step & sizes as per requirement.5) COUPLANTSSpecification Compliance: ASTM F519, F945 . BOEING BAC 5439-PSD622, 5968, 5980 . PRATT & WHITNEY PWA 286, 275, 1484, 36604, 36700, MCL E-205 Type II (ASTM F945), AMS 5544, 5536, 6359, 4037, 5608 (Haynes 188), 5508, 4375.Pack Sizes: 25-901 1 Gal. 25-905 5 Gal 25-955 55 Gal. 25-912 12 Oz. bottle (12-pack) 25-904 4 Oz. bottle (12-pack)

6) UT Cables

NDTE Enterprises manufacture all types of ultrasonic testing Cables needed to Ultrasonic machine Please refer our Ut cable list for your convenience.

HomeAbout UsProductsContact Us