Date post: | 10-Nov-2014 |
Category: |
Documents |
Upload: | alfonso-cordero |
View: | 14 times |
Download: | 0 times |
TL/H/7942
LM
2907/LM
2917
Fre
quency
toV
olta
ge
Converte
r
February 1995
LM2907/LM2917 Frequency to Voltage Converter
General DescriptionThe LM2907, LM2917 series are monolithic frequency to
voltage converters with a high gain op amp/comparator de-
signed to operate a relay, lamp, or other load when the input
frequency reaches or exceeds a selected rate. The tachom-
eter uses a charge pump technique and offers frequency
doubling for low ripple, full input protection in two versions
(LM2907-8, LM2917-8) and its output swings to ground for a
zero frequency input.
AdvantagesY Output swings to ground for zero frequency inputY Easy to use; VOUT e fIN c VCC c R1 c C1Y Only one RC network provides frequency doublingY Zener regulator on chip allows accurate and stable fre-
quency to voltage or current conversion (LM2917)
FeaturesY Ground referenced tachometer input interfaces directly
with variable reluctance magnetic pickupsY Op amp/comparator has floating transistor outputY 50 mA sink or source to operate relays, solenoids, me-
ters, or LEDs
Y Frequency doubling for low rippleY Tachometer has built-in hysteresis with either differen-
tial input or ground referenced inputY Built-in zener on LM2917Y g0.3% linearity typicalY Ground referenced tachometer is fully protected from
damage due to swings above VCC and below ground
ApplicationsY Over/under speed sensingY Frequency to voltage conversion (tachometer)Y SpeedometersY Breaker point dwell metersY Hand-held tachometerY Speed governorsY Cruise controlY Automotive door lock controlY Clutch controlY Horn controlY Touch or sound switches
Block and Connection Diagrams Dual-In-Line and Small Outline Packages, Top Views
TL/H/7942–1
Order Number LM2907M-8 or LM2907N-8
See NS Package Number M08A or N08E
TL/H/7942–2
Order Number LM2917M-8 or LM2917N-8
See NS Package Number M08A or N08E
TL/H/7942–3
Order Number LM2907N
See NS Package Number N14A
TL/H/7942–4
Order Number LM2917M or LM2917N
See NS Package Number M14A or N14A
C1995 National Semiconductor Corporation RRD-B30M115/Printed in U. S. A.
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Supply Voltage 28V
Supply Current (Zener Options) 25 mA
Collector Voltage 28V
Differential Input Voltage
Tachometer 28V
Op Amp/Comparator 28V
Input Voltage Range
Tachometer LM2907-8, LM2917-8 g28V
LM2907, LM2917 0.0V to a28V
Op Amp/Comparator 0.0V to a28V
Power Dissipation
LM2907-8, LM2917-8 1200 mW
LM2907-14, LM2917-14 1580 mW
(See Note 1)
Operating Temperature Range b40§C to a85§CStorage Temperature Range b65§C to a150§CSoldering Information
Dual-In-Line Package
Soldering (10 seconds) 260§CSmall Outline Package
Vapor Phase (60 seconds) 215§CInfrared (15 seconds) 220§C
See AN-450 ‘‘Surface Mounting Methods and Their Effect
on Product Reliability’’ for other methods of soldering sur-
face mount devices.
Electrical Characteristics VCC e 12 VDC, TA e 25§C, see test circuit
Symbol Parameter Conditions Min Typ Max Units
TACHOMETER
Input Thresholds VIN e 250 mVp-p @ 1 kHz (Note 2) g10 g25 g40 mV
Hysteresis VIN e 250 mVp-p @ 1 kHz (Note 2) 30 mV
Offset Voltage VIN e 250 mVp-p @ 1 kHz (Note 2)
LM2907/LM2917 3.5 10 mV
LM2907-8/LM2917-8 5 15 mV
Input Bias Current VIN e g50 mVDC 0.1 1 mA
VOH Pin 2 VIN e a125 mVDC (Note 3) 8.3 V
VOL Pin 2 VIN e b125 mVDC (Note 3) 2.3 V
I2, I3 Output Current V2 e V3 e 6.0V (Note 4) 140 180 240 mA
I3 Leakage Current I2 e 0, V3 e 0 0.1 mA
K Gain Constant (Note 3) 0.9 1.0 1.1
Linearity fIN e 1 kHz, 5 kHz, 10 kHz (Note 5) b1.0 0.3 a1.0 %
OP/AMP COMPARATOR
VOS VIN e 6.0V 3 10 mV
IBIAS VIN e 6.0V 50 500 nA
Input Common-Mode Voltage 0 VCCb1.5V V
Voltage Gain 200 V/mV
Output Sink Current VC e 1.0 40 50 mA
Output Source Current VE e VCC b2.0 10 mA
Saturation Voltage ISINK e 5 mA 0.1 0.5 V
ISINK e 20 mA 1.0 V
ISINK e 50 mA 1.0 1.5 V
2
Electrical Characteristics VCC e 12 VDC, TA e 25§C, see test circuit (Continued)
Symbol Parameter Conditions Min Typ Max Units
ZENER REGULATOR
Regulator Voltage RDROP e 470X 7.56 V
Series Resistance 10.5 15 X
Temperature Stability a1 mV/§C
TOTAL SUPPLY CURRENT 3.8 6 mA
Note 1: For operation in ambient temperatures above 25§C, the device must be derated based on a 150§C maximum junction temperature and a thermal resistance
of 101§C/W junction to ambient for LM2907-8 and LM2917-8, and 79§C/W junction to ambient for LM2907-14 and LM2917-14.
Note 2: Hysteresis is the sum aVTH b (bVTH), offset voltage is their difference. See test circuit.
Note 3: VOH is equal to */4 c VCC b 1 VBE, VOL is equal to (/4 c VCC b 1 VBE therefore VOH b VOL e VCC/2. The difference, VOH b VOL, and the mirror gain,
I2/I3, are the two factors that cause the tachometer gain constant to vary from 1.0.
Note 4: Be sure when choosing the time constant R1 c C1 that R1 is such that the maximum anticipated output voltage at pin 3 can be reached with I3 c R1. The
maximum value for R1 is limited by the output resistance of pin 3 which is greater than 10 MX typically.
Note 5: Nonlinearity is defined as the deviation of VOUT (@ pin 3) for fIN e 5 kHz from a straight line defined by the VOUT @ 1 kHz and VOUT @ 10 kHz.
C1 e 1000 pF, R1 e 68k and C2 e 0.22 mFd.
General Description (Continued)
The op amp/comparator is fully compatible with the ta-
chometer and has a floating transistor as its output. This
feature allows either a ground or supply referred load of up
to 50 mA. The collector may be taken above VCC up to a
maximum VCE of 28V.
The two basic configurations offered include an 8-pin device
with a ground referenced tachometer input and an internal
connection between the tachometer output and the op amp
non-inverting input. This version is well suited for single
speed or frequency switching or fully buffered frequency to
voltage conversion applications.
The more versatile configurations provide differential ta-
chometer input and uncommitted op amp inputs. With this
version the tachometer input may be floated and the op
amp becomes suitable for active filter conditioning of the
tachometer output.
Both of these configurations are available with an active
shunt regulator connected across the power leads. The reg-
ulator clamps the supply such that stable frequency to volt-
age and frequency to current operations are possible with
any supply voltage and a suitable resistor.
Test Circuit and Waveform
TL/H/7942–6
Tachometer Input Threshold Measurement
TL/H/7942–7
3
Typical Performance Characteristics
Total Supply Current Temperature
Zener Voltage vs
Output vs Temperature
Normalized Tachometer
Output vs Temperature
Normalized Tachometer
and I3 vs Supply Voltage
Tachometer Currents I2and I3 vs Temperature
Tachometer Currents I2
vs Temperature
Tachometer Linearity
vs Temperature
Tachometer Linearity
Tachometer Linearity vs R1
vs Temperature
Tachometer Input Hysteresis
Characteristics
Op Amp Output Transistor
Characteristics
Op Amp Output Transistor
TL/H/7942–5
4
Applications InformationThe LM2907 series of tachometer circuits is designed for
minimum external part count applications and maximum ver-
satility. In order to fully exploit its features and advantages
let’s examine its theory of operation. The first stage of oper-
ation is a differential amplifier driving a positive feedback
flip-flop circuit. The input threshold voltage is the amount of
differential input voltage at which the output of this stage
changes state. Two options (LM2907-8, LM2917-8) have
one input internally grounded so that an input signal must
swing above and below ground and exceed the input
thresholds to produce an output. This is offered specifically
for magnetic variable reluctance pickups which typically pro-
vide a single-ended ac output. This single input is also fully
protected against voltage swings to g28V, which are easily
attained with these types of pickups.
The differential input options (LM2907, LM2917) give the
user the option of setting his own input switching level and
still have the hysteresis around that level for excellent noise
rejection in any application. Of course in order to allow the
inputs to attain common-mode voltages above ground, input
protection is removed and neither input should be taken
outside the limits of the supply voltage being used. It is very
important that an input not go below ground without some
resistance in its lead to limit the current that will then flow in
the epi-substrate diode.
Following the input stage is the charge pump where the
input frequency is converted to a dc voltage. To do this
requires one timing capacitor, one output resistor, and an
integrating or filter capacitor. When the input stage changes
state (due to a suitable zero crossing or differential voltage
on the input) the timing capacitor is either charged or dis-
charged linearly between two voltages whose difference is
VCC/2. Then in one half cycle of the input frequency or a
time equal to 1/2 fIN the change in charge on the timing
capacitor is equal to VCC/2 c C1. The average amount of
current pumped into or out of the capacitor then is:
DQ
Te ic(AVG) e C1 c
VCC
2c (2fIN) e VCC c fIN c C1
The output circuit mirrors this current very accurately into
the load resistor R1, connected to ground, such that if the
pulses of current are integrated with a filter capacitor, then
VO e ic c R1, and the total conversion equation becomes:
VO e VCC c fIN c C1 c R1 c K
Where K is the gain constantÐtypically 1.0.
The size of C2 is dependent only on the amount of ripple
voltage allowable and the required response time.
CHOOSING R1 AND C1
There are some limitations on the choice of R1 and C1
which should be considered for optimum performance. The
timing capacitor also provides internal compensation for the
charge pump and should be kept larger than 500 pF for very
accurate operation. Smaller values can cause an error cur-
rent on R1, especially at low temperatures. Several consid-
erations must be met when choosing R1. The output current
at pin 3 is internally fixed and therefore VO/R1 must be less
than or equal to this value. If R1 is too large, it can become
a significant fraction of the output impedance at pin 3 which
degrades linearity. Also output ripple voltage must be con-
sidered and the size of C2 is affected by R1. An expression
that describes the ripple content on pin 3 for a single R1C2
combination is:
VRIPPLE e
VCC
2c
C1
C2c #1 b
VCC c fIN c C1
I2 J pk-pk
It appears R1 can be chosen independent of ripple, howev-
er response time, or the time it takes VOUT to stabilize at a
new voltage increases as the size of C2 increases, so a
compromise between ripple, response time, and linearity
must be chosen carefully.
As a final consideration, the maximum attainable input fre-
quency is determined by VCC, C1 and I2:
fMAX e
I2
C1 c VCC
USING ZENER REGULATED OPTIONS (LM2917)
For those applications where an output voltage or current
must be obtained independent of supply voltage variations,
the LM2917 is offered. The most important consideration in
choosing a dropping resistor from the unregulated supply to
the device is that the tachometer and op amp circuitry alone
require about 3 mA at the voltage level provided by the
zener. At low supply voltages there must be some current
flowing in the resistor above the 3 mA circuit current to op-
erate the regulator. As an example, if the raw supply varies
from 9V to 16V, a resistance of 470X will minimize the ze-
ner voltage variation to 160 mV. If the resistance goes un-
der 400X or over 600X the zener variation quickly rises
above 200 mV for the same input variation.
Typical Applications
Minimum Component Tachometer
TL/H/7942–8
5
Typical Applications (Continued)
‘‘Speed Switch’’ Load is Energized When fIN t
1
2RC
TL/H/7942–9
Zener Regulated Frequency to Voltage Converter
TL/H/7942–10
Breaker Point Dwell Meter
TL/H/7942–11
6
Typical Applications (Continued)
Voltage Driven Meter Indicating Engine RPM
VO e 6V @ 400 Hz or 6000 ERPM (8 Cylinder Engine)
TL/H/7942–12
Current Driven Meter Indicating Engine RPM
IO e 10 mA @ 300 Hz or 6000 ERPM (6 Cylinder Engine)
TL/H/7942–13
Capacitance Meter
VOUT e 1V–10V for CX e 0.01 to 0.1 mFd
(R e 111k)
TL/H/7942–14
7
Typical Applications (Continued)
Two-Wire Remote Speed Switch
TL/H/7942–15
100 Cycle Delay Switch
V3 steps up in voltage by the amountVCC c C1
C2
for each complete input cycle (2 zero crossings)TL/H/7942–16
Example:
If C2 e 200 C1 after 100 consecutive input cycles.
V3 e 1/2 VCC
8
Typical Applications (Continued)
Variable Reluctance Magnetic Pickup Buffer CircuitsPrecision two-shot output frequency
equals twice input frequency.
Pulse width e
VCC
2
C1
I2.
Pulse height e VZENER
TL/H/7942–39TL/H/7942–17
Finger Touch or Contact Switch
TL/H/7942–18
TL/H/7942–19
Flashing LED Indicates Overspeed
Flashing begins when fIN t 100 Hz.
Flash rate increases with input frequency
increase beyond trip point.
TL/H/7942–20
9
Typical Applications (Continued)
Frequency to Voltage Converter with 2 Pole Butterworth Filter to Reduce Ripple
fPOLE e
0.707
2qRC
uRESPONSE e
2.57
2qfPOLE
TL/H/7942–21
Overspeed Latch
TL/H/7942–22
Output latches when TL/H/7942–23
fIN e
R2
R1 a R2
1
RC
Reset by removing VCC.
10
Typical Applications (Continued)
Some Frequency Switch Applications May Require Hysteresis in the
Comparator Function Which can be Implemented in Several Ways:
TL/H/7942–24
TL/H/7942–25 TL/H/7942–26
TL/H/7942–27 TL/H/7942–28
11
Typical Applications (Continued)
Changing the Output Voltage for an Input Frequency of Zero
TL/H/7942–29
TL/H/7942–30
Changing Tachometer Gain Curve or Clamping the Minimum Output Voltage
TL/H/7942–31
TL/H/7942–32
12
Anti-Skid Circuit Functions
‘‘Select-Low’’ Circuit
TL/H/7942–33
TL/H/7942–34
VOUT is proportional to the lower of the
two input wheel speeds.
‘‘Select-High’’ Circuit
TL/H/7942–35
TL/H/7942–36
VOUT is proportional to the higher of
the two input wheel speeds.
‘‘Select-Average’’ Circuit
TL/H/7942–37
13
Equivalent Schematic Diagram
TL/H
/7942–38
*This
connection
made
on
LM
2907-8
and
LM
2917-8
only
.
**This
connection
made
on
LM
2917
and
LM
2917-8
only
.
14
15
Physical Dimensions inches (millimeters)
8-Lead (0.150× Wide) Molded Small Outline Package, JEDEC
Order Number LM2907M-8 or LM2917M-8
NS Package Number M08A
16
Physical Dimensions inches (millimeters) (Continued)
Molded SO Package (M)
Order Number LM2917M
NS Package Number M14A
Molded Dual-In-Line Package (N)
Order Number LM2907N-8 or LM2917N-8
NS Package Number N08E
17
LM
2907/LM
2917
Fre
quency
toV
oltage
Convert
er
Physical Dimensions inches (millimeters) (Continued)
Molded Dual-In-Line Package (N)
Order Number LM2907N or LM2917N
NS Package Number N14A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform can
into the body, or (b) support or sustain life, and whose be reasonably expected to cause the failure of the life
failure to perform, when properly used in accordance support device or system, or to affect its safety or
with instructions for use provided in the labeling, can effectiveness.
be reasonably expected to result in a significant injury
to the user.
National Semiconductor National Semiconductor National Semiconductor National SemiconductorCorporation Europe Hong Kong Ltd. Japan Ltd.1111 West Bardin Road Fax: (a49) 0-180-530 85 86 13th Floor, Straight Block, Tel: 81-043-299-2309Arlington, TX 76017 Email: cnjwge@ tevm2.nsc.com Ocean Centre, 5 Canton Rd. Fax: 81-043-299-2408Tel: 1(800) 272-9959 Deutsch Tel: (a49) 0-180-530 85 85 Tsimshatsui, KowloonFax: 1(800) 737-7018 English Tel: (a49) 0-180-532 78 32 Hong Kong
Fran3ais Tel: (a49) 0-180-532 93 58 Tel: (852) 2737-1600Italiano Tel: (a49) 0-180-534 16 80 Fax: (852) 2736-9960
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
This datasheet has been download from:
www.datasheetcatalog.com
Datasheets for electronics components.