.... lntertek Number : WUXH00032954 Applicant : ANHUI LIGHT INDUSTRIES INTERNATIONAL CO., LTD. ALIC MANSION, 19 MEISHAN ROAD, HEFEI,ANHUI, CHINA Attn : DAIYUN Date : Sep 04, 2014 Sample Description As Declared: Six (6) Styles Of Submitted Sample Said To Be : Item Name ST.PATRICK'S DAY HEADBOPPER HEADBAND Item No. G86058P P.O. No. 202-08402. Buyer CHINA BIZ & ASSOCIATES. Supplier Anhui Light Industries International Co.,Ltd. Goods Exported To USA. Country Of Origin China . Tests Conducted: As Requested By The Applicant, For Details Refer To Attached Pages Prepared And Checked By: For Intertek Testing Services Wuxi Ltd. Jessica Lu General Manager lntertek Testing Services Wuxi Ltd. No.6 Fubei Road, Xishan Economic Development Zone, Wuxi 2 141 01, Jiangsu, China Tel: +86 510 8821 4567 Fa x: +86 510 8820 0428 E-mail: consumergoods.wuxi@intertek.com Page 1 Of 4
Transcript
....
lntertek
Number : WUXH00032954
Applicant : ANHUI LIGHT INDUSTRIES INTERNATIONAL CO., LTD. ALIC MANSION, 19 MEISHAN ROAD, HEFEI,ANHUI, CHINA Attn : DAIYUN
Date : Sep 04, 2014
Sample Description As Declared: Six (6) Styles Of Submitted Sample Said To Be : Item Name ST.PATRICK'S DAY HEADBOPPER HEADBAND Item No. G86058P P.O. No. 202-08402. Buyer CHINA BIZ & ASSOCIATES. Supplier Anhui Light Industries International Co.,Ltd. Goods Exported To USA. Country Of Origin China .
Tests Conducted: As Requested By The Applicant, For Details Refer To Attached Pages
Prepared And Checked By: For Intertek Testing Services Wuxi Ltd.
Tests Conducted (As Requested By The Applicant) 1 Flammability Test
As Per Section 4.2 OfThe ASTM Standard Consumer Safety Specification For Toy Safety F963-11, The Sample Was Tested According To Annex AS Flammability Testing Procedure For Solids And Soft Toys.
Sample Ignition Point
Clover Headband Leg Point
Burn Length (inch)
2.3
Time (sec)
17.94
Actual Burn Rate (inch/sec)
0.13
Rounded# Burn Rate (inch/sec)
0.10
Limit (inch/sec)
0.1
All Styles OfThe Submitted Toy Samples Were Tested, The Above Result Only Showed The Most Severe Burn Rate OfThe Samples.
# = According To The ASTM F963 Flammability Requirement, The Burn Rate Shall Be Rounded To The Nearest Tenth.
Testing Period :Aug 20, 2014 To Sep 03, 2014
2 Total Lead (Pb) Content
As Per Section 4.3.5 Of The Astm Standard Consumer Safety Specification On Toy Safety F963-11, Test Method CPSC-CH-E1001-08.1, CPSC-CH-E1002-08.1 Or/And CPSC-CH-E1003-09.1 Was/Were Used And Total Lead Content Was Determined By Inductively Coupled Argon Plasma Spectrometry.
(I) Non-Surface Coating
Tested Component (1) (2)
ppm = Parts Per Million =mg/kg < =Less Than
Tested Components :
Result In ppm <10 <10
(1)Silver Grey Metal (Spring On Headwear). (2)Transparent Glue (Headwear).
Tests Conducted (As Requested By The Applicant) 3 Phthalate Content Test
Number : WUXH00032954
As Per Standard Operating Procedure For Determining Phthalates, Test Method CPSC-CH-C1001-09.3 Was Used And Phthalate Content Was Determined By Gas Chromatographic-Mass Spectrometric (GC-MS) Analysis.
Remark : The Above Limit Was Quoted According To US Consumer Product Safety Improvement Act 2008 (H.R.4040) & Amendment H.R. 2715 For Prohibition On Sale Of Certain Products Containing Specified Phthalates.
Detection Limit ~ 0.01% (W/W) ND ~ Not Detected
Tested Component : (3)Green Plastic (Headwear).
Date Sample Received :Aug 20, 2014 Testing Period: Aug 20, 2014 To Sep 03, 2014
This report Is made solely on the basis of your instructions and/or infonnation and materials supplied by you. It Is not Intended to be a recommendation for any particular course of adion. lntertek does not accept a duty of care or any other responsibility to any person other than the Gient in respect of this report and only accepts /iabi7ity to the Client insofar as is expressly contained in the terms and conditions governing Intettek's provision of services to you. Intertek makes no warranties or representations either express or Implied with respect to this report save as provided for in those tenns and conditions. We have aimed to conduct the Review on a dJ/igent and careful basis and we do not accept any liability to you for any /os5 anSing out of or in connection with this report, In contract tort by statute or otherwise, except in the event of our gross negligence or wiffuf misconduct.
Applicant: ANHUI LIGHT INDUSTRIES INTERNATIONAL CO., LTD. ALIC MANSION, 19 MEISHAN ROAD, HEFEI,ANHUI, CHINA Attn : DAIYUN
Date : Sep 04, 2014
Sample Description As Declared: Six (6) Styles Of Submitted Sample Said To Be : Item Name VALETINE HEADBAND Item No. G87088N P.O. No. 202-08401. Buyer CHINA BIZ & ASSOCIATES. Supplier Anhui Light Industries International Co.,Ltd. Goods Exported To USA. Country Of Origin China .
Tests Conducted: As Requested By The Applicant, For Details Refer To Attached Pages
Prepared And Checked By: For Intertek Testing Services Wuxi Ltd.
Tests Conducted (As Requested By The Applicant) 1 Flammability Test
As Per Section 4.2 Of The ASTM Standard Consumer Safety Specification For Toy Safety F963-11, The Sample Was Tested According To Annex AS Flammability Testing Procedure For Solids And Soft Toys.
Ignition Point
Red Heart Headband Leg Point
Burn Length (inch)
2.3
Time (sec)
17.94
Actual Burn Rate (inch/sec)
0.13
Rounded# Burn Rate (inch/sec)
0.10
Limit (inch/sec)
0.1
All Styles Of The Submitted Toy Samples Were Tested, The Above Result Only Showed The Most Severe Burn Rate OfThe Samples.
# = According To The ASTM F963 Flammability Requirement, The Burn Rate Shall Be Rounded To The Nearest Tenth.
Testing Period :Aug 20, 2014 To Sep 03, 2014
2 Total Lead (Pb) Content
As Per Section 4.3.5 Of The Astm Standard Consumer Safety Specification On Toy Safety F963-11, Test Method CPSC-CH-E1001-08.1, CPSC-CH-E1002-08.1 Or/And CPSC-CH-E1003-09.1 Was/Were Used And Total Lead Content Was Determined By Inductively Coupled Argon Plasma Spectrometry.
(I) Non-Surface Coating
Tested Component (1) (2)
ppm = Parts Per Million =mg/kg < =Less Than
Tested Components :
Result In ppm <10 <10
(1)Silver Grey Metal (Spring On Headwear). (2)Transparent Glue (Headwear).
Tests Conducted (As Requested By The Applicant) 3 Phthalate Content Test
Number : WUXH00032953
As Per Standard Operating Procedure For Determining Phthalates, Test Method CPSC-CH-C1001-09.3 Was Used And Phthalate Content Was Determined By Gas Chromatographic-Mass Spectrometric (GC-MS) Analysis.
Remark : The Above Limit Was Quoted According To US Consumer Product Safety Improvement Act 2008 (H.R.4040) & Amendment H.R. 2715 For Prohibition On Sale Of Certain Products Containing Specified Phthalates.
Date Sample Received :Aug 20, 2014 Testing Period :Aug 20, 2014 To Sep 03, 2014
This report is made solely on the basis of your tnstnx:tions and/or information and maten"a/s supplied by you. It is not intended to be a recommendation for any particular course of action. Intertek does not accept a duty of care or any other responsibility to any person other than the Gfent in respect of this report and only accepts liability to the Oierrt insofar as is expressly contained in the terms and conditions governing Intertek's provi5ion of services to you. Intertek makes no warranties or representations eitf~er express or implied witf1 respect to this report scwe as pro'.ltded for in those tem1s and conditions. We have aimed to conduct the Review on a diligent and careful basis and we do not accept any liability to you for any foss
arising out of or in mnllfflion with this refX!I1i in contract, tort by statute or othenvise_ except in tile event of our gross negligence or wilful misconduct.
Applicant: ANHUI LIGHT INDUSTRIES INTERNATIONAL CO., LTD. ALIC MANSION, 19 MEISHAN ROAD, HEFEI,ANHUI, CHINA Attn : DAIYUN
Sample Description As Declared: Six (6) Styles Of Submitted Sample Said To Be : Item Name PATRIOTIC HEADBAND Item No. G88145 P.O. No. 202-08400. Buyer CHINA BIZ & ASSOCIATES.
Date : Sep 04, 2014
Supplier Anhui Ught Industries International Co.,Ltd . Goods Exported To USA. Country Of Origin China.
Tests Conducted: As Requested By The Applicant, For Details Refer To Attached Pages
Prepared And Checked By: For Intertek Testing Services Wuxi Ltd .
Tests Conducted (As Requested By The Applicant) 1 Flammability Test
As Per Section 4.2 Of The ASTM Standard Consumer Safety Specification For Toy Safety F963-11, The Sample Was Tested According To Annex AS Flammability Testing Procedure For Solids And Soft Toys.
Ignition Point
Star Headband Leg Point
Burn Length (inch)
2.3
Time (sec)
17.94
Actual Burn Rate (inchjsec)
0.13
Rounded# Burn Rate (inch/sec)
0.10
Limit (inch/sec)
0.1
All Styles Of The Submitted Toy Samples Were Tested, The Above Result Only Showed The Most Severe Burn Rate OfThe Samples.
# = According To The ASTM F963 Flammability Requirement, The Burn Rate Shall Be Rounded To The Nearest Tenth.
Testing Period: Aug 20, 2014 To Sep 03,2014
2 Total Lead (Pb) Content
As Per Section 4.3.5 Of The Astrn Standard Consumer Safety Specification On Toy Safety F963-11, Test Method CPSC-CH-E1001-08.1, CPSC-CH-E1002-08.1 Or/And CPSC-CH-E1003-09.1 Was/Were Used And Total Lead Content Was Determined By Inductively Coupled Argon Plasma Spectrometry.
(I) Non-Surface Coating
Tested Component (1) (2)
ppm = Parts Per Million =mgfkg < = Less Than
Tested Components :
Result In ppm <10 <10
(1)Silver Grey Metal (Spring On Headwear). (2)Transparent Glue (Headwear).
Tests Conducted (As Requested By The Applicant) 3 Phthalate Content Test
Number : WUXH00032955
As Per Standard Operating Procedure For Determining Phthalates, Test Method CPSC-CH-C1001-09.3 Was Used And Phthalate Content Was Determined By Gas Chromatographic-Mass Spectrometric (GC-MS) Analysis.
Remark : The Above Limit Was Quoted According To US Consumer Product Safety Improvement Act 2008 (H.R.4040) & Amendment H.R. 2715 For Prohibition On Sale Of Certain Products Containing Specified Phthalates.
Detection Limit = 0.01% (W/W) NO = Not Detected
Tested Component : (3)White Plastic (Headwear).
Date Sample Received: Aug 20, 2014 Testing Period :Aug 20, 2014 To Sep 03, 2014
Thfs ~eport Is made solely on the basis of your instructions and/or information and materials supplied by you. Jt is not intended to be a recommendation for any particular course of adion. Intertek does not accept a duty of care or any other responsibility to any person other than the Client in respect of this report and only i!Ccepts liability to the Client insofar as is expressly contained in the tenns and conditiOns govemlng Intertek's provision of services to you. Intertek makes no warwnties or representations either express or implied with respect to this report save as provkfed for in those tem1s and conditions. We have aimed to conduct the Review on a diligent and careful basis and we do not accept any liability to you for any loss arising out of or in QJflnection with thiS report, in contract_ tort by statute or othenvise, except 1i1 the event of our gross negligence or wilful misconduct.
