+ All Categories
Home > Documents > Lo-Trim II Accessories The best just got better Argo announces … · The best just got better......

Lo-Trim II Accessories The best just got better Argo announces … · The best just got better......

Date post: 24-Jul-2020
Category:
Upload: others
View: 0 times
Download: 0 times
Share this document with a friend
1
The best just got better... Argo announces the standardization of galvanized steel across its residential hydronic baseboard products. Through the use of a two phase state-of-the-art manufacturing process Argo has taken the esthetically pleasing and clean-heat performance of residential baseboards to unprecedented levels of durability. During phase one all critical components of the baseboard including the vane, front and back plates are “hot-dipped” galvanized through an environmentally friendly no-lead process increasing rust corrosion resistance above that of traditional processes. Phase two incorporates a beautiful paint finish process which further increases corrosion resistance and durability providing users with a life-time solution to their hydronic heating needs. Argo’s versatile hydronic heating products are the perfect solution for all areas of the home including high moisture areas such as kitchens, bathrooms and even basements. 260 North Elm Street | Westfield, MA 01085 | 413-568-9571 www.sterlingbaseboard.com GLV-AR-1 PANEL TRIM II BASEBOARD COMMERCIAL / RESIDENTIAL HIGH OUTPUT BASEBOARD RADIATION LO TRIM II BASEBOARD • Low Profile • Quiet Operation • Advanced Design • Quick & Easy to Install LO-TRIM II BASEBOARD RADIATION Providing comfort to any room with style! RESIDENTIAL
Transcript
Page 1: Lo-Trim II Accessories The best just got better Argo announces … · The best just got better... Argo announces the standardization of galvanized steel across its residential hydronic

The best just got better... Argo announces the standardization of galvanized steel across its residential hydronic baseboard products.

Through the use of a two phase state-of-the-art manufacturing process

Argo has taken the esthetically pleasing and clean-heat performance of

residential baseboards to unprecedented levels of durability.

During phase one all critical components of the baseboard including

the vane, front and back plates are “hot-dipped” galvanized through an

environmentally friendly no-lead process increasing rust corrosion resistance

above that of traditional processes. Phase two incorporates a beautiful paint

finish process which further increases corrosion resistance and durability

providing users with a life-time solution to their hydronic heating needs.

Argo’s versatile hydronic heating products are the perfect solution for

all areas of the home including high moisture areas such as kitchens,

bathrooms and even basements.

260 North Elm Street | Westfield, MA 01085 | 413-568-9571 www.sterlingbaseboard.com

GLV-AR-1

PANEL�TRIM IIB A S E B OA R D

C O M M E R C I A L / R E S I D E N T I A L

HIGH OUTPUT BASEBOARD RADIATION

PT-6_Layout 2 8/3/15 9:26 AM Page 1

LO�TRIM IIB A S E B OA R D

• Low Profile

• Quiet Operation

• Advanced Design

• Quick & Easy to Install

LO-TRIM II BASEBOARD RADIATIONProviding comfort to any room with style!

R E S I D E N T I A L

LT-7

A MESTEK COMPANY

ARGO BASEBOARD260 North Elm Street • Westfield, MA 01085Tel: (413) 564-5975 • Fax: (413) 572-3764www.argobaseboard.com

Lo-Trim II AccessoriesA complete line of matching accessories designed for quick and easy snap-on installation. Theright piece for any job.

Single Element Lo-Trim II Hot Water Ratings BTU per hour perlinear foot of active (finned) length (with damper).

The use of Rating @ 4GPM is limited to installations where flow rate isknown to be equal to or greater than 4 GPM. If flow rate is unknown, use 1GPM rating.

Ratings include 15% addition to water heat capacity.

Hot water ratings shown are at the STANDARD WATER FLOW RATE of 500 lb/hr(1GPM) and 2,000 lbs/hr (4GPM) with 65º entering air temperature.

Friction loss through Argo Baseboard unit at 1 GPM (500 lbs/hr) is 47 MIL-INCHES per foot and at 4 GPM (2000 lbs/hr) is 525 MIL-INCHES PER FOOT.

Rating base on active length. Difference between active and total length is 3".

Aluminum fins are 2-1/8" x 2-1/8" x .008" thick, spaced 51 per foot (un-painted).

1 1/4[32]

2 5/8[67]

4 21/32[118]

13/16[21]

1 19/32[40]

2 7/8[73]

CAT-62839C

1 15/32[37]

7 15/32[190]

DIMENSIONS IN "[ ]" ARE SHOWNIN MILLIMETERS.

End Caps 3" left or right end caps that extend to the floor.

Outside Cornersavailable in 90° and 135° angles.

Inside Cornersavailable in 90°,and 135° angles.

3 Piece Splice2" Joining piece set, 7" Filler piece set, 14" Filler piece set. Each set contains 3 pieces.

Hinged Valve Enclosureleft or right 4" end caps extend to thefloor.

Wall EndsWall ends available in 3".

Model GPMAverage Hot Water Temperaure - BTU/HR./LIN. FT.

120°F 130°F 140°F 150°F 160°F 170°F 180°F 190°F 200°F

LT 1/2"4 215 269 328 390 450 520 590 670 740

1 204 255 311 370 430 490 560 630 700

LT 3/4"4 209 262 319 380 440 510 570 630 710

1 198 248 302 360 420 480 540 600 670

LT-7_Layout 2 8/3/15 9:38 AM Page 1

Recommended