12
7/21/2019 Log Subsets http://slidepdf.com/reader/full/log-subsets 1/12 November 2012 IHS Inc. E X I T EarthPAK Log Subsets Version 8.8
| Date post: | 05-Mar-2016 |
| Category: |
Documents |
| Upload: | hafidz-dezulfakar |
| View: | 222 times |
| Download: | 0 times |
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 112
November 2012
IHS Inc
EXI
T
EarthPAK
Log Subsets
Version 88
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 212
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 312
IHS Kingdom 88 1
EXIT
Log Subsets
Overview
There are numerous situations in which the total number of logs available in a project exceeds the
number of common logs that are required for every day interpretation To facilitate working with
log data you can create log subsets A log subset consists of any combination of digital raster or
composite logs
After a log subset is defined it is added to the Working Set and can then be used in Kingdom
software For example if you are planning to create a cross section displaying only gamma ray
and resistivity curves you might want to create a subset that includes only the GR and LLD logsAfter you add the log subset to the log working set you can easily create a cross section that
displays only GR and LLD curves and their aliases If you should later want to display a density
curve you will need to add it to your log subset or turn on a system-generated subset to make the
subset available for use in Kingdom software
There are four system-generated subsets All Digital Logs All Composite Logs All Raster
Logs and All Log Curves Each system subset is dynamic which means that any new log curves
that are imported edited or calculated will automatically be added to the appropriate subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 412
2 IHS Kingdom 88
Create a Log Subset
EXIT
Create a Log Subset
In this exercise we will create a log subset consisting of all the Resistivity logs in the Sooner
project
1 Open the Sooner project (Project gt Open Project gt sooner3dtks)
2 Click to make the Base Map active and then on the Kingdom main menu click Logs gt Log
Subset Management to open the Log Subset Management dialog box
3 In the Log Subset Management dialog box click the Create tab
4 Enter Gamma Ray and Resistivity as the Subset Name
5 Set the Create Subset Category to Digital Logs
6 In the Select One or More Log(s) list select GR and LLD
Your dialog box should look like Figure 1
Figure 1 - Log Subset Management dialog box
7 Click Apply
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 512
IHS Kingdom 88 3
Create a Log Subset
EXIT
Create a Working Set
1 Click the Working Set tab
2 Click ltlt to remove any subsets from the Working Set list
3 In the Select One or More Subset(s) list select Gamma Ray and Resistivity This subset is
e automatically moved to the Working Set list
4 Click OK to make the subsets available for use in your project
Create a Cross Section with GR and LLD Curves
1 Right-click in the active Base Map and select Digitize Arbitrary Line gt Cross Section
through Well(s) or use the Cross Section through Well(s) icon
2 Click the SOONER UNIT 20-8-7 and SOONER UNIT 6-21 wells
3 Double-click the SOONER UNIT 9-21 well to terminate the selection and display the cross
section
4 In the Current display data type text field select Cross Section (Depth)
5 Click the Set Scales icon to open the Settings dialog box
6 Click the Horiz Scale tab
7 Turn ON Use True Distance and set the Relative Scale to 1 inch = 1000 feet
8 Click the Vert Scale tab9 In the Vertical Display Scale area set Inches per Second to 50 feet
10 Click OK to close the dialog box
11 Click the Log Settings icon to open the Log Settings dialog box
12 In the Log Settings dialog box click the Define Curve Tracks tab
13 Check ON Depth Track Track 1 and Track 2 in the Select Tracks to Display list
14 Click the Scale and Style Setup tab
15 In the Category text field select Digital Logs
Note Observe that only the GR and LLD curves are available for selection
16 Click GR Track 1 and use the gt arrow to move it to the Displayed Curves list
17 Click LLD Track 2 and use the gt arrow to move it to the Displayed Curves list
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 612
4 IHS Kingdom 88
Create a Log Subset
EXIT
18 In the Displayed Curves list select the GR curve
19 In the Line area change Color to DarkGreen
20 In the Displayed Curves list select the LLD curve
21 Check ON Logarithm
22 Click Save Template to open the Save Settings dialog box and save these settings
23 Enter a File name for example GR_and_LLD and click Save
24 Click OK to close the Log Settings dialog box
Your cross section should look like the cross section in Figure 2 You might have to turn off
aliasing shading and so on
Figure 2 - Cross Section Displaying Logs from GR and LLD Log Subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 212
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 312
IHS Kingdom 88 1
EXIT
Log Subsets
Overview
There are numerous situations in which the total number of logs available in a project exceeds the
number of common logs that are required for every day interpretation To facilitate working with
log data you can create log subsets A log subset consists of any combination of digital raster or
composite logs
After a log subset is defined it is added to the Working Set and can then be used in Kingdom
software For example if you are planning to create a cross section displaying only gamma ray
and resistivity curves you might want to create a subset that includes only the GR and LLD logsAfter you add the log subset to the log working set you can easily create a cross section that
displays only GR and LLD curves and their aliases If you should later want to display a density
curve you will need to add it to your log subset or turn on a system-generated subset to make the
subset available for use in Kingdom software
There are four system-generated subsets All Digital Logs All Composite Logs All Raster
Logs and All Log Curves Each system subset is dynamic which means that any new log curves
that are imported edited or calculated will automatically be added to the appropriate subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 412
2 IHS Kingdom 88
Create a Log Subset
EXIT
Create a Log Subset
In this exercise we will create a log subset consisting of all the Resistivity logs in the Sooner
project
1 Open the Sooner project (Project gt Open Project gt sooner3dtks)
2 Click to make the Base Map active and then on the Kingdom main menu click Logs gt Log
Subset Management to open the Log Subset Management dialog box
3 In the Log Subset Management dialog box click the Create tab
4 Enter Gamma Ray and Resistivity as the Subset Name
5 Set the Create Subset Category to Digital Logs
6 In the Select One or More Log(s) list select GR and LLD
Your dialog box should look like Figure 1
Figure 1 - Log Subset Management dialog box
7 Click Apply
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 512
IHS Kingdom 88 3
Create a Log Subset
EXIT
Create a Working Set
1 Click the Working Set tab
2 Click ltlt to remove any subsets from the Working Set list
3 In the Select One or More Subset(s) list select Gamma Ray and Resistivity This subset is
e automatically moved to the Working Set list
4 Click OK to make the subsets available for use in your project
Create a Cross Section with GR and LLD Curves
1 Right-click in the active Base Map and select Digitize Arbitrary Line gt Cross Section
through Well(s) or use the Cross Section through Well(s) icon
2 Click the SOONER UNIT 20-8-7 and SOONER UNIT 6-21 wells
3 Double-click the SOONER UNIT 9-21 well to terminate the selection and display the cross
section
4 In the Current display data type text field select Cross Section (Depth)
5 Click the Set Scales icon to open the Settings dialog box
6 Click the Horiz Scale tab
7 Turn ON Use True Distance and set the Relative Scale to 1 inch = 1000 feet
8 Click the Vert Scale tab9 In the Vertical Display Scale area set Inches per Second to 50 feet
10 Click OK to close the dialog box
11 Click the Log Settings icon to open the Log Settings dialog box
12 In the Log Settings dialog box click the Define Curve Tracks tab
13 Check ON Depth Track Track 1 and Track 2 in the Select Tracks to Display list
14 Click the Scale and Style Setup tab
15 In the Category text field select Digital Logs
Note Observe that only the GR and LLD curves are available for selection
16 Click GR Track 1 and use the gt arrow to move it to the Displayed Curves list
17 Click LLD Track 2 and use the gt arrow to move it to the Displayed Curves list
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 612
4 IHS Kingdom 88
Create a Log Subset
EXIT
18 In the Displayed Curves list select the GR curve
19 In the Line area change Color to DarkGreen
20 In the Displayed Curves list select the LLD curve
21 Check ON Logarithm
22 Click Save Template to open the Save Settings dialog box and save these settings
23 Enter a File name for example GR_and_LLD and click Save
24 Click OK to close the Log Settings dialog box
Your cross section should look like the cross section in Figure 2 You might have to turn off
aliasing shading and so on
Figure 2 - Cross Section Displaying Logs from GR and LLD Log Subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 312
IHS Kingdom 88 1
EXIT
Log Subsets
Overview
There are numerous situations in which the total number of logs available in a project exceeds the
number of common logs that are required for every day interpretation To facilitate working with
log data you can create log subsets A log subset consists of any combination of digital raster or
composite logs
After a log subset is defined it is added to the Working Set and can then be used in Kingdom
software For example if you are planning to create a cross section displaying only gamma ray
and resistivity curves you might want to create a subset that includes only the GR and LLD logsAfter you add the log subset to the log working set you can easily create a cross section that
displays only GR and LLD curves and their aliases If you should later want to display a density
curve you will need to add it to your log subset or turn on a system-generated subset to make the
subset available for use in Kingdom software
There are four system-generated subsets All Digital Logs All Composite Logs All Raster
Logs and All Log Curves Each system subset is dynamic which means that any new log curves
that are imported edited or calculated will automatically be added to the appropriate subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 412
2 IHS Kingdom 88
Create a Log Subset
EXIT
Create a Log Subset
In this exercise we will create a log subset consisting of all the Resistivity logs in the Sooner
project
1 Open the Sooner project (Project gt Open Project gt sooner3dtks)
2 Click to make the Base Map active and then on the Kingdom main menu click Logs gt Log
Subset Management to open the Log Subset Management dialog box
3 In the Log Subset Management dialog box click the Create tab
4 Enter Gamma Ray and Resistivity as the Subset Name
5 Set the Create Subset Category to Digital Logs
6 In the Select One or More Log(s) list select GR and LLD
Your dialog box should look like Figure 1
Figure 1 - Log Subset Management dialog box
7 Click Apply
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 512
IHS Kingdom 88 3
Create a Log Subset
EXIT
Create a Working Set
1 Click the Working Set tab
2 Click ltlt to remove any subsets from the Working Set list
3 In the Select One or More Subset(s) list select Gamma Ray and Resistivity This subset is
e automatically moved to the Working Set list
4 Click OK to make the subsets available for use in your project
Create a Cross Section with GR and LLD Curves
1 Right-click in the active Base Map and select Digitize Arbitrary Line gt Cross Section
through Well(s) or use the Cross Section through Well(s) icon
2 Click the SOONER UNIT 20-8-7 and SOONER UNIT 6-21 wells
3 Double-click the SOONER UNIT 9-21 well to terminate the selection and display the cross
section
4 In the Current display data type text field select Cross Section (Depth)
5 Click the Set Scales icon to open the Settings dialog box
6 Click the Horiz Scale tab
7 Turn ON Use True Distance and set the Relative Scale to 1 inch = 1000 feet
8 Click the Vert Scale tab9 In the Vertical Display Scale area set Inches per Second to 50 feet
10 Click OK to close the dialog box
11 Click the Log Settings icon to open the Log Settings dialog box
12 In the Log Settings dialog box click the Define Curve Tracks tab
13 Check ON Depth Track Track 1 and Track 2 in the Select Tracks to Display list
14 Click the Scale and Style Setup tab
15 In the Category text field select Digital Logs
Note Observe that only the GR and LLD curves are available for selection
16 Click GR Track 1 and use the gt arrow to move it to the Displayed Curves list
17 Click LLD Track 2 and use the gt arrow to move it to the Displayed Curves list
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 612
4 IHS Kingdom 88
Create a Log Subset
EXIT
18 In the Displayed Curves list select the GR curve
19 In the Line area change Color to DarkGreen
20 In the Displayed Curves list select the LLD curve
21 Check ON Logarithm
22 Click Save Template to open the Save Settings dialog box and save these settings
23 Enter a File name for example GR_and_LLD and click Save
24 Click OK to close the Log Settings dialog box
Your cross section should look like the cross section in Figure 2 You might have to turn off
aliasing shading and so on
Figure 2 - Cross Section Displaying Logs from GR and LLD Log Subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 412
2 IHS Kingdom 88
Create a Log Subset
EXIT
Create a Log Subset
In this exercise we will create a log subset consisting of all the Resistivity logs in the Sooner
project
1 Open the Sooner project (Project gt Open Project gt sooner3dtks)
2 Click to make the Base Map active and then on the Kingdom main menu click Logs gt Log
Subset Management to open the Log Subset Management dialog box
3 In the Log Subset Management dialog box click the Create tab
4 Enter Gamma Ray and Resistivity as the Subset Name
5 Set the Create Subset Category to Digital Logs
6 In the Select One or More Log(s) list select GR and LLD
Your dialog box should look like Figure 1
Figure 1 - Log Subset Management dialog box
7 Click Apply
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 512
IHS Kingdom 88 3
Create a Log Subset
EXIT
Create a Working Set
1 Click the Working Set tab
2 Click ltlt to remove any subsets from the Working Set list
3 In the Select One or More Subset(s) list select Gamma Ray and Resistivity This subset is
e automatically moved to the Working Set list
4 Click OK to make the subsets available for use in your project
Create a Cross Section with GR and LLD Curves
1 Right-click in the active Base Map and select Digitize Arbitrary Line gt Cross Section
through Well(s) or use the Cross Section through Well(s) icon
2 Click the SOONER UNIT 20-8-7 and SOONER UNIT 6-21 wells
3 Double-click the SOONER UNIT 9-21 well to terminate the selection and display the cross
section
4 In the Current display data type text field select Cross Section (Depth)
5 Click the Set Scales icon to open the Settings dialog box
6 Click the Horiz Scale tab
7 Turn ON Use True Distance and set the Relative Scale to 1 inch = 1000 feet
8 Click the Vert Scale tab9 In the Vertical Display Scale area set Inches per Second to 50 feet
10 Click OK to close the dialog box
11 Click the Log Settings icon to open the Log Settings dialog box
12 In the Log Settings dialog box click the Define Curve Tracks tab
13 Check ON Depth Track Track 1 and Track 2 in the Select Tracks to Display list
14 Click the Scale and Style Setup tab
15 In the Category text field select Digital Logs
Note Observe that only the GR and LLD curves are available for selection
16 Click GR Track 1 and use the gt arrow to move it to the Displayed Curves list
17 Click LLD Track 2 and use the gt arrow to move it to the Displayed Curves list
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 612
4 IHS Kingdom 88
Create a Log Subset
EXIT
18 In the Displayed Curves list select the GR curve
19 In the Line area change Color to DarkGreen
20 In the Displayed Curves list select the LLD curve
21 Check ON Logarithm
22 Click Save Template to open the Save Settings dialog box and save these settings
23 Enter a File name for example GR_and_LLD and click Save
24 Click OK to close the Log Settings dialog box
Your cross section should look like the cross section in Figure 2 You might have to turn off
aliasing shading and so on
Figure 2 - Cross Section Displaying Logs from GR and LLD Log Subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 512
IHS Kingdom 88 3
Create a Log Subset
EXIT
Create a Working Set
1 Click the Working Set tab
2 Click ltlt to remove any subsets from the Working Set list
3 In the Select One or More Subset(s) list select Gamma Ray and Resistivity This subset is
e automatically moved to the Working Set list
4 Click OK to make the subsets available for use in your project
Create a Cross Section with GR and LLD Curves
1 Right-click in the active Base Map and select Digitize Arbitrary Line gt Cross Section
through Well(s) or use the Cross Section through Well(s) icon
2 Click the SOONER UNIT 20-8-7 and SOONER UNIT 6-21 wells
3 Double-click the SOONER UNIT 9-21 well to terminate the selection and display the cross
section
4 In the Current display data type text field select Cross Section (Depth)
5 Click the Set Scales icon to open the Settings dialog box
6 Click the Horiz Scale tab
7 Turn ON Use True Distance and set the Relative Scale to 1 inch = 1000 feet
8 Click the Vert Scale tab9 In the Vertical Display Scale area set Inches per Second to 50 feet
10 Click OK to close the dialog box
11 Click the Log Settings icon to open the Log Settings dialog box
12 In the Log Settings dialog box click the Define Curve Tracks tab
13 Check ON Depth Track Track 1 and Track 2 in the Select Tracks to Display list
14 Click the Scale and Style Setup tab
15 In the Category text field select Digital Logs
Note Observe that only the GR and LLD curves are available for selection
16 Click GR Track 1 and use the gt arrow to move it to the Displayed Curves list
17 Click LLD Track 2 and use the gt arrow to move it to the Displayed Curves list
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 612
4 IHS Kingdom 88
Create a Log Subset
EXIT
18 In the Displayed Curves list select the GR curve
19 In the Line area change Color to DarkGreen
20 In the Displayed Curves list select the LLD curve
21 Check ON Logarithm
22 Click Save Template to open the Save Settings dialog box and save these settings
23 Enter a File name for example GR_and_LLD and click Save
24 Click OK to close the Log Settings dialog box
Your cross section should look like the cross section in Figure 2 You might have to turn off
aliasing shading and so on
Figure 2 - Cross Section Displaying Logs from GR and LLD Log Subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 612
4 IHS Kingdom 88
Create a Log Subset
EXIT
18 In the Displayed Curves list select the GR curve
19 In the Line area change Color to DarkGreen
20 In the Displayed Curves list select the LLD curve
21 Check ON Logarithm
22 Click Save Template to open the Save Settings dialog box and save these settings
23 Enter a File name for example GR_and_LLD and click Save
24 Click OK to close the Log Settings dialog box
Your cross section should look like the cross section in Figure 2 You might have to turn off
aliasing shading and so on
Figure 2 - Cross Section Displaying Logs from GR and LLD Log Subset
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 712
IHS Kingdom 88 5
Create a Log Subset
EXIT
Edit Log Subsets
After you have created a subset you can modify the subset using the Edit tab of the Log Subset
Management dialog box You can rename the subset and add or remove curves from it
1 With the Base Map active on the Kingdom main menu click Logs gt Log SubsetManagement to open the Log Subset Management dialog box
2 In the Log Subset Management dialog box click the Edit tab
3 In the Select a Log Subset text field select the Gamma Ray and Resistivity subset
4 In the Category text field select Digital Logs
5 Click Show All Subsets to open the View Log Subsets dialog box
A list of all the currently available subsets is displayed in the window
6 To look at the individual log curve names that comprise the subset expand the folder by
pressing the + symbol
Figure 3 - View Log Subsets dialog box - Gamma Ray and Resistivity Subset
7 Click Close to close the View Log Subsets dialog box
8 Click OK to close the Log Subset Management dialog box
A quick glance at your cross section shows that there is no LLD curve available for the
SOONER UNIT 20-8-7 well
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 812
6 IHS Kingdom 88
Create a Log Subset
EXIT
9 Place the cursor on the borehole symbol at the top of the vertical view and right-click
10 Select List Well Data to open the Well Summary dialog box
11 Scroll down to see the list of curves available for this well and note that the well contains a
SFLU resistivity log
12 Click Cancel to close the Well Summary dialog box
Edit Subset
At this point there are two options
bull Alias the LLD curve to include the SFLU curve
bull Edit the subset you created previously and add the SFLU curve to it In this exercise we will
edit the subset
1 Open the Log Subset Management dialog box and click the Edit tab
2 In the Select One or More Log(s) list select the SFLU log curve
Your dialog box should look like Figure 4
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 912
IHS Kingdom 88 7
Create a Log Subset
EXIT
Figure 4 - Log Subset Management dialog box - Edit tab
3 Click OK
4 Reopen the Log Settings dialog box by clicking Logs gt Settings on the Kingdom main menu
5 Click the Scale and Style Setup tab
The SFLU curve is now displayed in the list of Available Curves
6 Click to select and highlight SFLU
7 In the Tracks list select Track 2
8 Use the gt arrow to move it to the Displayed Curves list
9 In the Displayed Curves list select SFLU Track 2
10 In Line area change the Color from default Red if desired
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1012
8 IHS Kingdom 88
Create a Log Subset
EXIT
11 In the Settings Scale area for Left Value enter (type) a value of 1 and for Right Value enter
(type) a value of 100
Note If you wish to use these log settings for future cross sections click Save Template to save
the settings in a template
12 Click OK
Now all of the wells in the cross section display resistivity curves (Figure 5)
Figure 5 - Completed Cross Section
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1112
IHS Kingdom 88 9
Create a Log Subset
EXIT
Copy and Delete Log Subsets
1 Open the Log Subset Management dialog box and click the Copy tab
2 Select the subset name you want to change In this case select Gamma Ray and Resistivity
3 Enter the new name (Gamma Ray and Resistivity copy) for the subset in the New Log
Subset Name text field
4 Click Apply The new name is added to the Log Subset to Copy window
5 To delete a subset click the Delete tab
6 Select the subset(s) to delete In this exercise select the Gamma Ray and Resistivity copy
subset you just created
7 Click Apply
8 A message box opens with the following information
The deletion operation is irreversible Are you sure you want to delete the selected
Log Subset(s)
9 Click Yes
10 Click Cancel to close the Log Subset Management dialog box
Note Log Subsets do not apply to the Log Editor For example if you create a log subset of
gamma ray and resistivity curves and wish to display all the logs for a given well in the log
editor you can do this without having to edit the log subset working set
Note Log Subsets do apply to the Log Table If you select a subset that contains only resistivity
logs and want to display all the curves for a given well in the log table you must first add
the All Digital Curves subset back into your working set
Congratulations you successfully completed the Log Subset tutorial
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
7212019 Log Subsets
httpslidepdfcomreaderfulllog-subsets 1212
10 IHS Ki d 8 8
Create a Log Subset
EXIT
