8/19/2019 LOG VAMOS

1/28

+++ HUAWEI 2016-03-05 00:47:51O&M #3381430%%DEA BTS: IDTYPE=BYNAME, BTSNAME="MGR007MG1_TSEL_PerumahanMempaya";%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:48:03O&M #3381431%%MOD BTS: IDTYPE=BYNAME, BTSNAME="MGR007MG1_TSEL_PerumahanMempaya", FLEXABISMODE=FLEX_ABIS;%%RETCODE = 0 Execution succeeded.

When [BTS:Flex Abis Mode] of BTS [MGR007MG1_TSEL_PerumahanMempaya] is set to FLEX_ABIS(Flex Abis), you are advised not to set idle timeslots.

--- END

+++ HUAWEI 2016-03-05 00:48:28O&M #3381434%%ACT BTS: IDTYPE=BYNAME, BTSNAME="MGR007MG1_TSEL_PerumahanMempaya", TRXIDTYPE=BYID;%%RETCODE = 0 Execution succeeded.

If idle timeslots are configured and [BTS:Flex Abis Mode] is set to "NO" or [BTS:Abis ByPass Mode] is set to TRUE for active BTS [MGR007MG1_TSEL_PerumahanMempaya], [BTSOTHPARA:Abis Idle TS Allocate Strategy] cannot be set to "IDLETSALLOC_1" or "IDLETSALLOC_2".If [BTSOTHPARA:Abis Idle TS Allocate Strategy] is not set to "IDLETSALLOC_1" or"IDLETSALLOC_2" for BTS [MGR007MG1_TSEL_PerumahanMempaya], the strategy for rese

rving idle timeslots for PDCHs cannot be used.The control plane subsystem allocated to BTS [MGR007MG1_TSEL_PerumahanMempaya] is [BTS:CTRLSRN=0/CTRLSN=2/CPUNO=2] and the subsystem status is "Normal".

--- END

+++ HUAWEI 2016-03-05 00:48:56O&M #3381436%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", PWRCTRLOPTIMIZEDEN=YES;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:48:56O&M #3381437%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", MEASURETYPE=ComMeasReport;%%

8/19/2019 LOG VAMOS

2/28

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:48:57O&M #3381438%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 235237603 [GCELLPWRBASIC:Power Control Switch] is must be set to "Power control III" when [GCELLVAMOS:VAMOS Switch] of cell[MGR007MG1_TSEL_PerumahanMempayaMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 00:48:58O&M #3381439%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", SDCCHWaitMREn=ON;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:52:38O&M #3381450%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:52:49O&M #3381452%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:52:50O&M #3381453%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

3/28

+++ HUAWEI 2016-03-05 00:52:50O&M #3381455%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR007MG1_TSEL_PerumahanMempayaMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 00:52:51O&M #3381456%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:53:34O&M #3381460%%DEA BTS: IDTYPE=BYNAME, BTSNAME="MGR012MG1_TSEL_TanjungBatuHitam";%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:55:04O&M #3381467

%%MOD BTS: IDTYPE=BYNAME, BTSNAME="MGR012MG1_TSEL_TanjungBatuHitam", FLEXABISMODE=FLEX_ABIS;%%RETCODE = 235233929 When [BTS:Service Type] of the current BTS is set to a value other than "TDM", [BTS:Flex Abis Mode] can be set only to "Fix Abis".

--- END

+++ HUAWEI 2016-03-05 00:57:10O&M #3381493%%MOD BTS: IDTYPE=BYNAME, BTSNAME="MGR012MG1_TSEL_TanjungBatuHitam", FLEXABISMODE=FLEX_ABIS;%%

RETCODE = 235233929 When [BTS:Service Type] of the current BTS is set to a value other than "TDM", [BTS:Flex Abis Mode] can be set only to "Fix Abis".

--- END

+++ HUAWEI 2016-03-05 00:58:15O&M #3381507%%LST BTS: LSTTYPE=BYBTSNAME, BTSNAME="MGR012MG1_TSEL_TanjungBatuHitam";%%

8/19/2019 LOG VAMOS

4/28

RETCODE = 0 Execution succeeded.

List BTS-------- BTS Index BTS Name BTS Type BTS Description Separate Mode Service Type Flex Abis Mode Abis ByPass Mode Config Ring BTS Multiplexing Mode Main Port No. IP Phy Trans Type Support for Unified Data Configuration Configure RFU by Slot Work Mode Preferential Logical TRXs Multiplexed on a TRX Board Support Normalized 3012 Series Base Stations BCCH TRX RSL Multiplexing Mode BBU Baseband Resource Pool License Share in BBU Carrier Pool Number of Licenses Shared by BBU Carrier Pool Abis Transmission Cable Detection Switch HostType Active Status Father Site Index Abis Mode OML In-Port No.  OML In-Timeslot No.(8K) OML Logic No. Reverse OML Logic No. Number of 2 Mbit/s in-ports in BTS OML Out-BSC Subrack No. OML Out-BSC Slot No. OML Out-BSCPort No. OML Out-BSC Timeslot No.(8K) CTRL Subrack No. CTRL Slot No. CPU No.  Reverse In-BTS Port No. Reverse In-BTS Ts No. Reverse Out-BSC Subrack No. Reverse Out-BSC Slot No. Reverse Out-BSC Port No. Reverse Out-BSC Ts No. Father DXX Index

18 MGR012MG1_TSEL_TanjungBatuHitam BTS3900A GSM MGR012MG1 Support IP Fix Abis Not Support No MODE2_1

IP_OVER_FE/GE Support E1

MODE_NULL

Off No Single Host DEACTIVATED AUTO

18 0

<

NULL> (Number of results = 1)

--- END

+++ HUAWEI 2016-03-05 00:58:35O&M #3381513%%LST BTS: LSTTYPE=BYBTSNAME, BTSNAME="MGR007MG1_TSEL_PerumahanMempaya";%%RETCODE = 0 Execution succeeded.

List BTS-------- BTS Index BTS Name BTS Type BTS Description Separate Mode Service Type Flex Abis Mode Abis ByPass Mode Config Ring BTS Multiplexing Mode Main Port No. IP Phy Trans Type Support for Unified Data Configu

ration Configure RFU by Slot Work Mode Preferential Logical TRXs Multiplexedon a TRX Board Support Normalized 3012 Series Base Stations BCCH TRX RSL Multiplexing Mode BBU Baseband Resource Pool License Share in BBU Carrier Pool Number of Licenses Shared by BBU Carrier Pool Abis Transmission Cable Detection Switch HostType Active Status Father Site Index Abis Mode OML In-Port No. OML In-Timeslot No.(8K) OML Logic No. Reverse OML Logic No. Number of 2 Mbit/sin-ports in BTS OML Out-BSC Subrack No. OML Out-BSC Slot No. OML Out-BSC Port No. OML Out-BSC Timeslot No.(8K) CTRL Subrack No. CTRL Slot No. CPU No. Reverse In-BTS Port No. Reverse In-BTS Ts No. Reverse Out-BSC Subrack No. Reverse Out-BSC Slot No. Reverse Out-BSC Port No. Reverse Out-BSC Ts No. Father DX

8/19/2019 LOG VAMOS

5/28

X Index

13 MGR007MG1_TSEL_PerumahanMempaya BTS3900 GSM MGR007MG1 Support TDM Flex Abis Not Support No MODE2_1

0 Support E1 NO

MODE_NULLOff No On ACTIVATED AUTO 0 24

8 13 10 24 16

248 0 2 2 (Number of results = 1)

--- END

+++ HUAWEI 2016-03-05 00:59:09O&M #3381520

%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:59:10O&M #3381522%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:59:11O&M #3381523%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 00:59:11O&M #3381524%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR007MG1_TSEL_PerumahanMempayaMG2",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

8/19/2019 LOG VAMOS

6/28

8/19/2019 LOG VAMOS

7/28

WRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:01O&M #3381802%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:01O&M #3381803%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 235237603 [GCELLPWRBASIC:Power Control Switch] is must be set to "Pow

er control III" when [GCELLVAMOS:VAMOS Switch] of cell[MGR012MG1_TSEL_TanjungBatuHitamMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:02O&M #3381804%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:03O&M #3381806%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:03O&M #3381808%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

8/28

+++ HUAWEI 2016-03-05 01:13:04O&M #3381809%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 235237603 [GCELLPWRBASIC:Power Control Switch] is must be set to "Power control III" when [GCELLVAMOS:VAMOS Switch] of cell[MGR012MG1_TSEL_TanjungBatuHitamMG2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:05O&M #3381813%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:05O&M #3381814%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:06O&M #3381816

%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:06O&M #3381818%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitc

h=ON;%%RETCODE = 235237603 [GCELLPWRBASIC:Power Control Switch] is must be set to "Power control III" when [GCELLVAMOS:VAMOS Switch] of cell[MGR012MG1_TSEL_TanjungBatuHitamMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:08

8/19/2019 LOG VAMOS

9/28

O&M #3381819%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:24O&M #3381827%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:24O&M #3381828%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:25O&M #3381829%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:25O&M #3381831%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR012MG1_TSEL_TanjungBatuHitamMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:26O&M #3381832%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

8/19/2019 LOG VAMOS

10/28

--- END

+++ HUAWEI 2016-03-05 01:13:26O&M #3381834%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:28O&M #3381835%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:29O&M #3381837%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:29O&M #3381839

%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR012MG1_TSEL_TanjungBatuHitamMG2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:30O&M #3381841%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

11/28

+++ HUAWEI 2016-03-05 01:13:31O&M #3381843%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:31O&M #3381844%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:32O&M #3381845%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamM

G3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:33O&M #3381847%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%

RETCODE = 0 Execution succeeded.

[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR012MG1_TSEL_TanjungBatuHitamMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:33O&M #3381848%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR012MG1_TSEL_TanjungBatuHitamMG3", S

DCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:48O&M #3381853%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG2

8/19/2019 LOG VAMOS

12/28

", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:49O&M #3381854%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:49O&M #3381855%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:50O&M #3381856%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG2",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[MGR014MG1_TSEL_Tanjung

KelumpangMG2] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR014MG1_TSEL_TanjungKelumpangMG2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:51O&M #3381857%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG2", SDCCHWaitMREn=ON;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:51O&M #3381859%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG3", PWRCTRLSW=PWR3;%%

8/19/2019 LOG VAMOS

13/28

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:52O&M #3381860%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:52O&M #3381861%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:13:53O&M #3381862%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG3",VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[MGR014MG1_TSEL_TanjungKelumpangMG3] is set to "On".

[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR014MG1_TSEL_TanjungKelumpangMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:13:53O&M #3381864%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR014MG1_TSEL_TanjungKelumpangMG3", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:10O&M #3381870%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

8/19/2019 LOG VAMOS

14/28

--- END

+++ HUAWEI 2016-03-05 01:14:10O&M #3381871%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:11O&M #3381877%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG3", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:12O&M #3381878%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:12O&M #3381880

%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

Cell[N_TJN054MD1_TBG_DepatiRahatMD2]: It is recommended that [GCELLCHMGAD:AMR TCH/H Prior Cell Load Threshold] be less than [GCELLCHMGAD:TCH Traffic Busy Threshold].

--- END

+++ HUAWEI 2016-03-05 01:14:13O&M #3381882%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD3", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

15/28

+++ HUAWEI 2016-03-05 01:14:14O&M #3381883%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:15O&M #3381885%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:15O&M #3381887%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG3", PWRCTRLSW=PWR3;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:16O&M #3381890%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:17O&M #3381892%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:18O&M #3381894%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG3", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

16/28

+++ HUAWEI 2016-03-05 01:14:18O&M #3381895%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG1", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:19O&M #3381896%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG2", PWRCTRLSW=PWR3;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:20O&M #3381899%%SET GCELLPWRBASIC: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG3", PWRCTRLSW=PWR3;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:28O&M #3381905%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:28O&M #3381906%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:29O&M #3381909%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

17/28

+++ HUAWEI 2016-03-05 01:14:29O&M #3381910%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:30O&M #3381911%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

Cell[N_TJN054MD1_TBG_DepatiRahatMD2]: It is recommended that [GCELLCHMGAD:AMR TCH/H Prior Cell Load Threshold] be less than [GCELLCHMGAD:TCH Traffic Busy Threshold].

--- END

+++ HUAWEI 2016-03-05 01:14:30O&M #3381914%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:31O&M #3381915

%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:31O&M #3381917%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:32O&M #3381918%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

8/19/2019 LOG VAMOS

18/28

--- END

+++ HUAWEI 2016-03-05 01:14:33O&M #3381920%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:33O&M #3381921%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:34O&M #3381923%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:35O&M #3381926

%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG1", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:35O&M #3381928%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG2", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:36O&M #3381929%%SET GCELLPWR3: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG3", PWRCTRLOPTIMIZEDEN=YES;%%RETCODE = 0 Execution succeeded.

8/19/2019 LOG VAMOS

19/28

--- END

+++ HUAWEI 2016-03-05 01:14:45O&M #3381935%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:46O&M #3381936%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:46O&M #3381937%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:47O&M #3381939

%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:48O&M #3381941%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

Cell[N_TJN054MD1_TBG_DepatiRahatMD2]: It is recommended that [GCELLCHMGAD:AMR TCH/H Prior Cell Load Threshold] be less than [GCELLCHMGAD:TCH Traffic Busy Threshold].

--- END

8/19/2019 LOG VAMOS

20/28

+++ HUAWEI 2016-03-05 01:14:48O&M #3381944%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:49O&M #3381946%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:51O&M #3381948%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG2", MEASURETYPE=ComMeasReport;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:52O&M #3381951%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:53O&M #3381953%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:53O&M #3381954%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG2", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

8/19/2019 LOG VAMOS

21/28

+++ HUAWEI 2016-03-05 01:14:54O&M #3381956%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:55O&M #3381957%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG1", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:55O&M #3381960%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG2", MEASURETYPE=ComMeasReport;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:14:56O&M #3381962%%SET GCELLCCUTRANSYS: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG3", MEASURETYPE=ComMeasReport;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:17O&M #3381971%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG1", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[MGR018MG1_TSEL_AirKelikMG1] is set to "On".

[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR018MG1_TSEL_AirKelikMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:18O&M #3381972

8/19/2019 LOG VAMOS

22/28

%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG2", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[MGR018MG1_TSEL_AirKelikMG2] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR018MG1_TSEL_AirKelikMG2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:18O&M #3381974%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG3", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [

GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[MGR018MG1_TSEL_AirKelikMG3] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [MGR018MG1_TSEL_AirKelikMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:19O&M #3381976%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD1", Vamo

sSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[N_TJN054MD1_TBG_DepatiRahatMD1] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [N_TJN054MD1_TBG_DepatiRahatMD1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:20O&M #3381978%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD2", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

8/19/2019 LOG VAMOS

23/28

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[N_TJN054MD1_TBG_DepatiRahatMD2] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [N_TJN054MD1_TBG_DepatiRahatMD2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:20O&M #3381979%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD3", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[N_TJN054MD1_TBG_DepatiRahatMD3] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VA

MOS Switch] of cell [N_TJN054MD1_TBG_DepatiRahatMD3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:21O&M #3381981%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG1", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN026MG1_TSEL_MempiuMG1] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN026MG1_TSEL_MempiuMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:22

O&M #3381982%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG2", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN026MG1_TSEL_MempiuMG2] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VA

8/19/2019 LOG VAMOS

24/28

MOS Switch] of cell [TJN026MG1_TSEL_MempiuMG2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:23O&M #3381985%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG3", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN026MG1_TSEL_MempiuMG3] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN026MG1_TSEL_MempiuMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:23O&M #3381988%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG1", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN033MG1_DMT_MengkubangMG1] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN033MG1_DMT_MengkubangMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:24O&M #3381990%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG2", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN033MG1_DMT_MengkubangMG2] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN033MG1_DMT_MengkubangMG2] is set to "On".

--- END

8/19/2019 LOG VAMOS

25/28

+++ HUAWEI 2016-03-05 01:15:24O&M #3381991%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG3", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN033MG1_DMT_MengkubangMG3] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN033MG1_DMT_MengkubangMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:25O&M #3381993%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG1", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%

RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN036MG1_TBG_TerongMG1] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN036MG1_TBG_TerongMG1] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:26O&M #3381994%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG2", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN036MG1_TBG_TerongMG2] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN036MG1_TBG_TerongMG2] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:26O&M #3381996%%SET GCELLVAMOS: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG3", VamosSwitch=ON, VamosAssSwitch=ON, VamosIntraHoSwitch=ON, VamosMainTsc=0, VamosSubTsc=2, VamosLoadReuseSwitch=ON, VamosQualReuseSwitch=ON, VamosQualUndoPntSwitch=ON;%%

8/19/2019 LOG VAMOS

26/28

RETCODE = 0 Execution succeeded.

[GCELLHOAD:Waiting for MR on SDCCH Switch] is suggested to be set to "On" when [GCELLVAMOS:Allow Channel Multiplex in Assignment] of cell[TJN036MG1_TBG_TerongMG3] is set to "On".[GCELLPWRBASIC:SAIC Allowed] is suggested to be set to "Yes" when [GCELLVAMOS:VAMOS Switch] of cell [TJN036MG1_TBG_TerongMG3] is set to "On".

--- END

+++ HUAWEI 2016-03-05 01:15:47O&M #3382010%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:48

O&M #3382012%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:49O&M #3382013%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="MGR018MG1_TSEL_AirKelikMG3", SDCCHWaitMREn=ON;%%

RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:49O&M #3382015%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:50O&M #3382017%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

Cell[N_TJN054MD1_TBG_DepatiRahatMD2]: It is recommended that [GCELLCHMGAD:AMR TC

8/19/2019 LOG VAMOS

27/28

H/H Prior Cell Load Threshold] be less than [GCELLCHMGAD:TCH Traffic Busy Threshold].

--- END

+++ HUAWEI 2016-03-05 01:15:51O&M #3382018%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="N_TJN054MD1_TBG_DepatiRahatMD3", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:52O&M #3382019%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:52O&M #3382021%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:53O&M #3382023%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN026MG1_TSEL_MempiuMG3", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:53O&M #3382025

%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:54O&M #3382026

8/19/2019 LOG VAMOS

28/28

%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:55O&M #3382027%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN033MG1_DMT_MengkubangMG3", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:55O&M #3382029%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG1", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:56O&M #3382032%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG2", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END

+++ HUAWEI 2016-03-05 01:15:57O&M #3382034%%SET GCELLHOAD: IDTYPE=BYNAME, CELLNAME="TJN036MG1_TBG_TerongMG3", SDCCHWaitMREn=ON;%%RETCODE = 0 Execution succeeded.

--- END