Passage/Privacy Long Plate Door Hardware Installation Instructions Updated June 2016 Skip to Step if your door has pre-drilled bore holes. See “Door Prep Template” For 2-3/8” Backset: For 2-3/4” Backset Threaded Privacy Pin Hole (Privacy Only) Door - Outside Grandeur Long Plate Drilling Template (Scale 1 to 1[full size]) (1) Locate the hole locations for your long plate on this template. (FAV = Fifth Ave., GVC = Grande Victorian, PAR = Parthenon, WIN = Windsor) (2) Place drilling template on your door, centering the 2 1/8” cross-bore hole. Keep template parallel with door edge. (3) Mark the hole locations for your long plate on the door. (4) Drill holes using a 7/64” diameter drill bit. Then go to step E on the installation instructions. DOOR EDGE: 2-3/4” from center of cross bore DOOR EDGE: 2-3/8” from center of cross bore DOOR EDGE: 2-3/8” from center of cross bore DOOR EDGE: 2-3/4” from center of cross bore Refer to Drilling Template on opposite page Door - Outside Emergency Release Hole (Privacy Only) Door - Outside Mounting Plate Door - Outside 1 3 2 Push onto mounting plate Rotate plate clockwise to lock into holes Emergency Release Hole (Privacy Only) Door - Outside Screw in the Privacy Pin (Privacy Only) Emergency Release Hole (Privacy Only) PK144 Rev3 06022016 For assistance call 1-844-372-6848 Monday through Friday, 7 am to 5 pm Mountain Time or visit www.GrandeurHardware.com/support
Transcript
Passage/PrivacyLong Plate Door HardwareInstallation InstructionsUpdated June 2016
Skip to Step if your door has pre-drilled bore holes.
See “Door Prep Template”
For 2-3/8” Backset:
For 2-3/4” Backset
Threaded Privacy Pin Hole(Privacy Only)
Door - Outside
Grandeur Long Plate Drilling Template (Scale 1 to 1[full size])
(1) Locate the hole locations for your long plate on this template. (FAV = Fifth Ave., GVC = Grande Victorian, PAR = Parthenon, WIN = Windsor)(2) Place drilling template on your door, centering the 2 1/8” cross-bore hole. Keep template parallel with door edge.(3) Mark the hole locations for your long plate on the door.(4) Drill holes using a 7/64” diameter drill bit. Then go to step E on the installation instructions.
DO
OR
EDG
E: 2
-3/4
” fro
m c
en
ter o
f cro
ss b
ore
DO
OR
EDG
E: 2
-3/8
” fro
m c
en
ter o
f cro
ss b
ore
DO
OR
EDG
E: 2
-3/8
” fro
m c
en
ter o
f cro
ss b
ore
DO
OR
EDG
E: 2
-3/4
” fro
m c
en
ter o
f cro
ss b
ore
Refer to Drilling Template on opposite page Door - Outside
Emergency Release Hole(Privacy Only)
Door - Outside
Mounting Plate
Door - Outside
1
3
2
Push ontomountingplate
Rotate plate clockwiseto lock into holes
Emergency Release Hole(Privacy Only)
Door - Outside
Screw in thePrivacy Pin
(Privacy Only)
Emergency Release Hole(Privacy Only)
PK144 Rev3 06022016For assistance call 1-844-372-6848 Monday through Friday, 7 am to 5 pm Mountain Time or visit www.GrandeurHardware.com/support
Grandeur Long Plate Drilling Template (Scale 1 to 1[full size])
(1) Locate the hole locations for your long plate on this template. (FAV = Fifth Ave., GVC = Grande Victorian, PAR = Parthenon, WIN = Windsor)(2) Place drilling template on your door, centering the 2 1/8” cross-bore hole. Keep template parallel with door edge.(3) Mark the hole locations for your long plate on the door.(4) Drill holes using a 7/64” diameter drill bit. Then go to step E on the installation instructions.
DO
OR
EDG
E: 2
-3/4
” fro
m c
en
ter o
f cro
ss b
ore
DO
OR
EDG
E: 2
-3/8
” fro
m c
en
ter o
f cro
ss b
ore
DO
OR
EDG
E: 2
-3/8
” fro
m c
en
ter o
f cro
ss b
ore
DO
OR
EDG
E: 2
-3/4
” fro
m c
en
ter o
f cro
ss b
ore
Out
side
Insid
e
PK14
4 Re
v.3
0602
2016
For a
ssista
nce c
all 1-
844-
372-
6848
Mon
day t
hrou
gh Fr
iday,
7 am
to 5
pm M
ount
ain Ti
me o
r visi
t www
.Gra
ndeu
rHar
dwar
e.com
/supp
ort
Door Hardware Installation Instructions
Deadbolt Tongue must be EXTENDED during installation.
A BFace of Door
Edgeof Door
Centerline
For 2-3/8” Backset3-1/2”
2-3/8”
3-3/4”2-3/4”
Cross BoreHole - 2-1/8”Diameter
For 2-3/4” BacksetDoor Thickness
Centerline
Edge BoreHole - 1”Diameter
FaceplateMortise Area
C DDeadbolt Latch
Updated July 2015
!Edge BoreHole
Tailpiece must be VERTICAL during installation.
! #4
#5A
#5B
E FOutside Assembly (Part #’s 4, 5A & 5B )
Deadbolt Adaptor Plate(Part #6 )
2-3/8”Machine Screws(Part #7 )
Inside of Door
#10
5/8”Machine Screws(Part #9 )
G #11
#13
#3
#12
DoorStop
Door Jamb
Page 1 – PK147 Rev.3 06022016
Single Cylinder Deadbolt
For thicker doors, please call customer service.
For assistance call 1-844-372-6848 Mon-Fri, 7 am—5pm MSTor visit www.GrandeurHardware.com/support
