2
ENOTE: Product specifications subject to change without notice. Updated 08.2017 DIMENSIONS ORDERING INFORMATION Sample Part Number: LSMWL4X-6-18-2LR-8 W-(H)-AT SPECIFICATIONS: INTERNAL The LSMWL4X is configured with 120/277V input with solid state charging circuitry. Standard features include low voltage disconnect, AC lockout and brownout protection. SPECIFICATIONS: EXTERNAL The LSMWL4X is constructed with a durable NEMA 4X rated fiber- glass cabinet. Terminal connectors allow for larger gauge wires to be connected for remote loads. Industrial gray finish is standard. Emer- , c i t s a l p o m r e h t t c a p m i h g i h m o r f d e d l o m e r a s d a e h g n i t h g i l y e c n e g (LR) PAR36 style heads are standard. Integrated mounting holes en- sure proper and secure installation. External test switch and monitor LED are standard. SPECIFICATIONS: ELECTRICAL BATTERY: The LSMWL4X is designed with a maintenance free, sealed valve regulated lead acid battery that provides a minimum emergency duration of 90 minutes (for the listed rating). Recharge time of the battery is 48 hours. The maximum battery operating tem- perature is +40°C and the minimum is +10°C without internal heater option, with the internal heater the minimum operating temperature is -20°C. Nickel Cadmium batteries are available in several configura- tions. CIRCUIT: The LSMWL4X utilizes a high-efficiency two stage char- ger providing precise float voltage control with low voltage disconnect protection. All components used in the circuitry are temperature com- pensated. The charger also has brownout and short circuit protection. Charger status is easily determined via a dual diagnostic LED display which indicates AC/ON and High Charge. A magnetic test switch al- lows maintenance personnel to quickly determine the operational sta- tus of the unit and lamp load, (magnet included). AUTOTEST See next page for details. EMERGENCY HEADS The LSMWL4X is normally supplied with two (2) top mounted (LR) PAR36 style 9W heads. Lamp head styles are constructed of high impact thermoplastic. Please note: (LR) PAR36 style food-prep ap- proved lenses are also available when ordering- TC (teflon coated). [1]NOTE: Nickel-cadmium. Must select NC from options when selecting Ni-Cd. [2]NOTE: Must specify voltage. [4]NOTE: Teflon is a registered trademark of Dupont. [5]NOTE: Cabinet size may vary based on product configuration. WARRANTY The LSMWL4X comes with a 5-year factory warranty. Lamps are not covered under the warranty. Deliberate damage, misuse, improper in- stallation effectively cancel the warranty. LSMWL4X NEMA 4 AND 4X | WET BAA SPECIFICATIONS: MECHANICAL The LSMWL4X is constructed with a durable NEMA 4X rated fiber- glass cabinet. Industrial gray finish is standard. Weatherproof emer- gency lighting heads are molded from high impact thermoplastic. Ex- ternal test switch and monitor LED are standard. MODEL OPERATION Pb-A (Capacity) LSMWL4X 6V 12V 24V 18 (6V) 27 (6V, 12V) 36 (6V, 12V) 60 (6V, 12V) 72 (6V) 100 (6V) 120 (6V, 12V) 140 (12V) 160 (12V) 180 (12V) 200 (6V) 280 (24V) 360 (12V, 24V) Ni-Cd 3 (Capacity) 22 (6V) 42 (6V, 12V) 54 (6V) 90 (6V, 12V) 100 (24V) 130 (12V) 200 (12V, 24V) Emergency Heads 3LR (triple PAR36) 2LR (double PAR36) 1LR (single PAR36) 0 (no heads) Lamps See Chart on Next Page OPTIONS AT (autotest) AM (ampmeter) CS120 (cord set, 120V only) IH (internal heater) TD 2 (time delay- 0, 5, 10, 20 mins.) IRT 2 (infrared testing) NC 1 (nickle-cadium battery) TC 3 (teflon coating) VM (voltmeter) WG (wireguard) © 2018, Life Safety Lighting, Inc. ALL RIGHTS RESERVED Life Safety Lighting 215-584-0156 • 1366 Trail Ridge Rd. Longmont, CO 80504 • www.lifesafetylighting.com
