LTC6258/LTC6259/LTC6260
6258960fa
1For more information www.linear.com/LTC6258
APPLICATIONSn Micropower Active Filtersn Portable Instrumentationn Battery or Solar Powered Systemsn Automotive Electronics
n Gain Bandwidth Product: 1.3MHzn Low Quiescent Current: 20µAn C-Load™ Op Amp Drives all Capacitive Loadsn Offset Voltage: 400µV Maximumn Rail-to-Rail Input and Outputn Supply Voltage Range: 1.8V to 5.25Vn EMI Rejection Ratio: 45dB at 1GHzn Input Bias Current: 75nA Maximumn CMRR/PSRR: 95dB/90dBn Shutdown Current: 7µA Maximumn Operating Temperature Range: –40°C to 125°Cn Single in 6-Lead TSOT-23, 2mm × 2mm DFN
Packagesn Dual in 8-Lead MS8, MS10, TS0T-23, 2mm × 2mm
DFN Packagesn Quad in MS16 Package
TYPICAL APPLICATION
DESCRIPTION
1.3MHz, 20µA Power Efficient Rail-to-Rail I/O
Op Amps
The LTC®6258/LTC6259/LTC6260 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with or without capacitive loads. They feature 1.3MHz gain-bandwidth product, 0.24V/µs slew rate while consuming only 20µA of supply current per amplifier operating on supply voltages ranging from 1.8V to 5.25V. The combination of low supply current, low supply volt-age, high gain bandwidth product and low noise makes the LTC6258 family unique among rail-to-rail input/output op amps with similar supply current. These operational amplifiers are ideal for power efficient applications.
For applications that require power-down, the LTC6258 in 2mm × 2mm DFN and LTC6259 MS10 packages respectively offer shutdown which reduces the current consumption to 7µA maximum.
The LTC6258 family can be used as plug-in replacements for many commercially available op amps to reduce power and improve input/output range and performance.L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and Over-The-Top and C-Load are trademarks of Analog Devices, Inc. All other trademarks are the property of their respective owners.
Low Noise Reference
FEATURES
Reference Buffer Noise Density
–+
5V
V+OUT
LTC6258
6258960 TA01
22µF22µF
RIN12.7k
22µFIN OUT
GND
LT6656
* 2.7K + 22µF FILTER
OP AMP, 44µF CLOADOP AMPFILTERED REFERENCEREFERENCE OUTPUTINSTRUMENT ONLY
FREQUENCY (kHz)0.01 0.1 1 10 1000
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
NOIS
E DE
NSIT
Y (n
V/√H
z)
6258960 TA01a
LTC6258/LTC6259/LTC6260
26258960fa
For more information www.linear.com/LTC6258
ABSOLUTE MAXIMUM RATINGS
Supply Voltage: V+ – V– ...........................................5.5VInput Voltage ................................... V– – 0.2 to V+ + 0.2Input Current: +IN, –IN, SHDN (Note 2) ............... ±10mAOutput Current: OUT ........................................... ±20mAOutput Short-Circuit Duration (Note 3) ............ IndefiniteOperating Temperature Range (Note 4) ..... –40°C to 125°C
(Note 1)
DC PACKAGE6-LEAD (2mm × 2mm × 0.8mm) PLASTIC DFN
TOP VIEW
OUT
–IN
SHDN
V+
+IN
V– 4
57V–
6
3
2
1
TJMAX = 150°C, qJA = 80°C/W (NOTE 6) EXPOSED PAD (PIN 7) IS V–, MUST BE SOLDERED TO PCB
TOP VIEW
OUTA
–INA
+INA
V–
V+
OUTB
–INB
+INB
DC PACKAGE8-LEAD (2mm × 2mm × 0.8mm) PLASTIC DFN
9V–
4
1
2
3 6
5
7
8
TJMAX = 150°C, qJA = 80°C/W (NOTE 6)
EXPOSED PAD (PIN 9) IS V–, MUST BE SOLDERED TO PCB
1234
8765
TOP VIEW
TS8 PACKAGE8-LEAD PLASTIC TSOT-23
V+
OUTB–INB+INB
OUTA–INA+INA
V– +–
+–
TJMAX = 150°C, qJA = 195°C/W (NOTE 6)
1234
OUTA–INA+INA
V–
8765
V+
OUTB–INB+INB
TOP VIEW
MS8 PACKAGE8-LEAD PLASTIC MSOP
+–+
–
TJMAX = 150°C, qJA = 163°C/W (NOTE 6)
12345
OUTA–INA+INA
V–
SHDNA
109876
V+
OUTB–INB+INBSHDNB
TOP VIEW
MS PACKAGE10-LEAD PLASTIC MSOP
+–+
–
TJMAX = 150°C, qJA = 160°C/W (NOTE 6)
12345678
OUTA–INA+INA
V+
+INB–INB
OUTBNC
161514131211109
OUTD–IND+INDV–
+INC–INCOUTCNC
TOP VIEW
MS PACKAGE16-LEAD PLASTIC MSOP
+–
+–
+–
+–
TJMAX = 150°C, qJA = 125°C/W (NOTE 6)
1
2
3
6
5
4
TOP VIEW
S6 PACKAGE6-LEAD PLASTIC TSOT-23
V+
SHDN
–IN
OUT
V–
+IN
+ –
TJMAX = 150°C, qJA = 192°C/W (NOTE 6)
PIN CONFIGURATION
Specified Temperature Range (Note 5) LTC6258I/LTC6259I/LTC6260I ............–40°C to 85°C LTC6258H/LTC6259H/LTC6260H ...... –40°C to 125°C
Maximum Junction Temperature .......................... 150°CStorage Temperature Range .................. –65°C to 150°CLead Temperature (Soldering, 10 sec)TS8, MS8, MS only ............................................... 300°C
LTC6258/LTC6259/LTC6260
6258960fa
3For more information www.linear.com/LTC6258
ORDER INFORMATION
5V ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VSUPPLY = 5V, VCM = VOUT = VSUPPLY/2, CL = 10pF, VSHDN is unconnected.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage VCM = V– + 0.3V
l
–400 –1000
100 400 1000
µV µV
VCM = V+ – 0.3V
l
–400 –1000
100 400 1000
µV µV
∆VOS/∆T Input Offset Voltage Drift VCM = V– + 0.3V, V+ – 0.3V 1.5 µV/°C
IB Input Bias Current (Note 7) VCM = V– + 0.3V l –75 –5 75 nA
VCM = V+ – 0.3V l –75 0 75 nA
IOS Input Offset Current VCM = V– + 0.3V l –75 –1 75 nA
VCM = V+ – 0.3V l –75 –1 75 nA
en Input Voltage Noise Density f = 1kHz 38 nV/√Hz
Input Noise Voltage f = 0.1Hz to 10Hz 2 µVP-P
in Input Current Noise Density f = 1kHz, VCM = 0V to 4V f = 1kHz, VCM = 4V to 5V
500 500
fA/√Hz fA/√Hz
RIN Input Resistance Differential Common Mode
1 10
MΩ MΩ
TAPE AND REEL (MINI) TAPE AND REEL PART MARKING* PACKAGE DESCRIPTIONSPECIFIED TEMPERATURE RANGE
LTC6258IS6#TRMPBF LTC6258IS6#TRPBF LTGWD 6-Lead Plastic TSOT-23 –40°C to 85°C
LTC6258HS6#TRMPBF LTC6258HS6#TRPBF LTGWD 6-Lead Plastic TSOT-23 –40°C to 125°C
LTC6258IDC#TRMPBF LTC6258IDC#TRPBF LGZS 6-Lead Plastic DFN (2mm × 2mm × 0.8mm) –40°C to 85°C
LTC6258HDC#TRMPBF LTC6258HDC#TRPBF LGZS 6-Lead Plastic DFN (2mm × 2mm × 0.8mm) –40°C to 125°C
LTC6259ITS8#TRMPBF LTC6259ITS8#TRPBF LTGWX 8-Lead Plastic TSOT-23 –40°C to 85°C
LTC6259HTS8#TRMPBF LTC6259HTS8#TRPBF LTGWX 8-Lead Plastic TSOT-23 –40°C to 125°C
LTC6259IDC#TRMPBF LTC6259IDC#TRPBF LGWT 8-Lead (2mm × 2mm × 0.8mm) Plastic DFN –40°C to 85°C
LTC6259HDC#TRMPBF LTC6259HDC#TRPBF LGWT 8-Lead (2mm × 2mm × 0.8mm) Plastic DFN –40°C to 125°C
TUBE
LTC6259IMS8#PBF LTC6259IMS8#TRPBF LTGWW 8-Lead Plastic MSOP –40°C to 85°C
LTC6259HMS8#PBF LTC6259HMS8#TRPBF LTGWW 8-Lead Plastic MSOP –40°C to 125°C
LTC6259IMS#PBF LTC6259IMS8#TRPBF LTGWY 10-Lead Plastic MSOP –40°C to 85°C
LTC6259HMS#PBF LTC6259HMS8#TRPBF LTGWY 10-Lead Plastic MSOP –40°C to 125°C
LTC6260IMS#PBF LTC6260IMS#TRPBF 6260 16-Lead Plastic MSOP –40°C to 85°C
LTC6260HMS#PBF LTC6260HMS#TRPBF 6260 16-Lead Plastic MSOP –40°C to 125°CConsult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Parts ending with PBF are RoHS and WEEE Compliant.For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/.
http://www.linear.com/product/LTC6258#orderinfo
LTC6258/LTC6259/LTC6260
46258960fa
For more information www.linear.com/LTC6258
5V ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VSUPPLY = 5V, VCM = VOUT = VSUPPLY/2, CL = 10pF, VSHDN is unconnected.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITSCIN Input Capacitance Differential
Common Mode0.65 1.2
pF pF
CMRR Common Mode Rejection Ratio VCM = 0.3V to 3.5V VCM = –0.1V to 5.1V
l
l
66 64
95 95
dB dB
IVR Input Voltage Range l –0.1 5.1 VPSRR Power Supply Rejection Ratio VCM = 0.4V, VS = 1.8V to 5.25V
l
78 68
90 dB dB
Supply Voltage Range l 1.8 5.25 VAV Large Signal Gain VOUT = 0.5V to 4.5V, RLOAD = 100k
l
14 2.8
40 V/mV V/mV
VOUT = 0.5V to 4.5V, RLOAD = 10k
l
3.5 0.5
10 V/mV V/mV
VOL Output Swing Low (Input Overdrive 30mV). Measured from V–
No Load
l
12 40 50
mV mV
ISINK = 100µA
l
80 105 120
mV mV
ISINK = 1mA
l
145 180 250
mV mV
VOH Output Swing High (Input Overdrive 30mV). Measured from V+
No Load
l
25 40 65
mV mV
ISOURCE = 100µA
l
35 55 100
mV mV
ISOURCE = 1mA
l
100 140 350
mV mV
ISC Output Short-Circuit Current
l
4 1
10 mA mA
IS Supply Current per Amplifier
l
16 11
20 23 25
µA µA
Supply Current in Shutdown
l
4 5 7
µA µA
ISHDN Shutdown Pin Current VSHDN = 0.6V VSHDN = 1.5V
l
l
60 0
200 15
nA nA
VIL SHDN Input Low Voltage Disable l 0.6 VVIH SHDN Input High Voltage Enable l 1.5 VtON Turn-On Time SHDN Toggle from 0V to 5V 152 µstOFF Turn-Off Time SHDN Toggle from 5V to 0V 7 µsGBW Gain-Bandwidth Product f = 10kHz
l
1.0 0.4
1.3 MHz MHz
tS Settling Time, 0.5V to 4.5V, Unity Gain 0.1% 0.01%
14 18
µs µs
SR Slew Rate AV = –1, VOUT = 0.5V to 4.5V, CLOAD = 10pF, RF = RG = 10kΩ
l
0.2 0.1
0.24 V/µs V/µs
FPBW Full Power Bandwidth (Note 8) 4VP-P 20 kHzTHD+N Total Harmonic Distortion and Noise f = 500Hz, AV = 2, RL = 4kΩ, VOUTP-P = 1V
VIN = 2.25V to 2.75V0.025
72% dB
ILEAK Output Leakage Current in Shutdown VSHDN = 0V, VOUT = 0V VSHDN = 0V, VOUT = 5V
l
l
100 100
nA nA
%MP Large Signal Overshoot VIN = 0.5V to 4.5V, AV = 1, CL = 100nF 2.7 %EMIRR Electromagnetic Interference Rejection Ratio Input Power –10dB to Input Pins at 1GHz 45 dB
LTC6258/LTC6259/LTC6260
6258960fa
5For more information www.linear.com/LTC6258
1.8V ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VSUPPLY = 1.8V, VCM = VOUT = 0.4V, CL = 10pF, VSHDN is unconnected.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOS Input Offset Voltage VCM = V– + 0.3V
l
–400 –1000
100 400 1000
µV µV
VCM = V+ – 0.3V
l
–400 –1000
100 400 1000
µV µV
∆VOS/∆T Input Offset Voltage Drift VCM = V– + 0.3V, V+ – 0.3V 1.5 µV/°C
IB Input Bias Current (Note 7) VCM = V– + 0.3V l –75 2 75 nA
VCM = V+ – 0.3V l –75 5 75 nA
IOS Input Offset Current VCM = V– + 0.3V l –75 2 75 nA
VCM = V+ – 0.3V l –75 2 75 nA
en Input Voltage Noise Density f = 1kHz, VCM = 0.4V 38 nV/√Hz
Input Noise Voltage f = 0.1Hz to 10Hz 2 µVP-P
in Input Current Noise Density f = 1kHz, VCM = 0V to 0.8V f = 1kHz, VCM = 1V to 1.8V
500 500
fA/√Hz fA/√Hz
RIN Input Resistance Differential Common Mode
1 10
MΩ MΩ
CIN Input Capacitance Differential Common Mode
0.65 1.2
pF pF
CMRR Common Mode Rejection Ratio VCM = 0.2V to 1.6V
l
70 61
90 dB dB
IVR Input Voltage Range l –0.1 1.9 V
PSRR Power Supply Rejection Ratio VCM = 0.4V, VS = 1.8V to 5.25V
l
78 68
90 dB dB
AV Large Signal Gain VOUT = 0.5V to 1.3V, RLOAD = 100k
l
15 1.6
50 V/mV V/mV
VOUT = 0.5V to 1.3V, RLOAD = 10k
l
4 0.4
10 V/mV V/mV
VOL Output Swing Low (Input Overdrive 30mV), Measured from V–
No Load
l
15 30 50
mV mV
ISINK = 100µA
l
80 110 130
mV mV
ISINK = 1mA
l
150 200 230
mV mV
LTC6258/LTC6259/LTC6260
66258960fa
For more information www.linear.com/LTC6258
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.Note 2: The inputs are protected by back-to-back diodes as well as ESD protection diodes to each power supply. If the differential input voltage exceeds 1.4V or the input extends more than 500mV beyond the power supply, the input current should be limited to less than 10mA.Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum rating when the output is shorted indefinitely.Note 4: LTC6258I/LTC6259I/LTC6260I and LTC6258H/LTC6259H/LTC6260H are guaranteed functional over the temperature range of –40°C to 125°C.
1.8V ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VSUPPLY = 1.8V, VCM = VOUT = 0.4V, CL = 10pF, VSHDN is unconnected.SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VOH Output Swing High (Input Overdrive 30mV), Measured from V+
No Load
l
25 40 50
mV mV
ISOURCE = 100µA
l
35 60 100
mV mV
ISOURCE = 1mA
l
95 140 300
mV mV
ISC Output Short-Circuit Current
l
4 1
10 mA mA
IS Supply Current per Amplifier
l
17 10
20 21 23
µA µA
Supply Current in Shutdown
l
1.0 1.5 2
µA µA
ISHDN Shutdown Pin Current VSHDN = 0.5V VSHDN = 1.5V
l
l
50 0
80 10
nA nA
VIL SHDN Input Low Voltage Disable l 0.5 V
VIH SHDN Input High Voltage Enable l 1.5 V
tON Turn-On Time SHDN Toggle From 0V to 1.8V 47 µs
tOFF Turn-Off Time SHDN Toggle From 1.8V to 0V 17 µs
GBW Gain-Bandwidth Product f = 10kHz
l
1.0 0.4
1.3 MHz MHz
TS Settling Time, 0.3V to 1.5V, Unity Gain 0.1% 0.01%
7 12
µs µs
SR Slew Rate AV = –1, VOUT = 0.3V to 1.5V, CLOAD = 10pF RF = RG = 10kΩ
l
0.16 0.1
0.22 V/µs V/µs
FPBW Full Power Bandwidth (Note 8) 1.2VP-P 58 kHz
THD+N Total Harmonic Distortion and Noise f = 500Hz, AV = 2, RL = 4kΩ, VOUTP-P = 1V VIN = 0.65V to 0.15V
0.04 68
% dB
Note 5: The LTC6258I/LTC6259I/LTC6260I are guaranteed to meet specified performance from –40°C to 85°C. The LTC6258H/LTC6259H/LTC6260H are guaranteed to meet specified performance from –40°C to 125°C.Note 6: Thermal resistance varies with the amount of PC board metal connected to the package. The specified values are for short traces connected to the leads.Note 7: The input bias current is the average of the currents into the positive and negative input pins.Note 8: Full power bandwidth is calculated from the slew rate FPBW = SR/π • VP-P.
LTC6258/LTC6259/LTC6260
6258960fa
7For more information www.linear.com/LTC6258
TYPICAL PERFORMANCE CHARACTERISTICS
Input Offset Drift Distribution VOS vs Supply Voltage (25°C)VOS vs Common Mode Voltage
VOS vs IOUT
Input Bias Current vs Common Mode Voltage
Input Bias Current vs Common Mode Voltage
Input VOS Histogram Input VOS Histogram VOS vs Temperature
VS = ±2.5VVCM = 0V
VOS (µV)–350 –250 –150 –50 50 150 250 3500
10
20
30
40
50
60
70
80
90
100
NUM
BER
OF P
ARTS
6258 G01
VS = ±2.5VVCM = 2.2V
VOS (µV)–350 –250 –150 –50 50 150 250 3500
10
20
30
40
50
60
70
80
90
100
NUM
BER
OF P
ARTS
6258 G02
VS = ±2.5VVCM = 0V
TEMPERATURE (°C)–40 –25 –10 5 20 35 50 65 80 95 110 125
–500
–400
–300
–200
–100
0
100
200
300
400
500
V OS
(µV)
6258 G03
VS = ±2.5VVCM=0V
HGRADEIND
DISTRIBUTION (µV/°C)–5 –4 –3 –2 –1 0 1 2 3 4 5
0
1
2
3
4
5
6
7
8
9
10
11
NUM
BER
OF U
NITS
6258 G04
VCM = 0.4V
SUPPLY VOLTAGE (V)1.8 2.4 3.0 3.6 4.2 4.8 5.4
–200
–160
–120
–80
–40
0
40
80
120
160
200
V OS
(µV)
6258 G05
VS = 5V
VCM (V)–0.5 0.5 1.5 2.5 3.5 4.5 5.5
–500
–400
–300
–200
–100
0
100
200
300
400
500
V OS
(µV)
6258 G06
VS = ±2.5VVCM = 0V –40°C
25°C125°C
IOUT (mA)–5 –4 –3 –2 –1 0 1 2 3 4 5
–1
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
V OS
(mV)
6258 G07
VS = 5V +IN–IN
VCM (V)0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
–20
–16
–12
–8
–4
0
4
8
12
16
20
INPU
T BI
AS C
URRE
NT (n
A)
6258 G08
VS = 1.8V +IN–IN
VCM (V)0 0.3 0.6 0.9 1.2 1.5 1.8
–20
–16
–12
–8
–4
0
4
8
12
16
20
INPU
T BI
AS C
URRE
NT (n
A)
6258 G09
LTC6258/LTC6259/LTC6260
86258960fa
For more information www.linear.com/LTC6258
TYPICAL PERFORMANCE CHARACTERISTICS
Supply Current vs Temperature Per Channel
Output Saturation Voltage vs Load Current
Output Saturation Voltage vs Load Current
Output Short-Circuit Current vs Supply Voltage (Sourcing)
Output Short-Circuit Current vs Supply Voltage (Sinking)
0.1Hz to 10Hz Output Voltage Noise
Input Bias Current vs Supply Voltage Input Bias Current vs Temperature
Supply Current vs Supply Voltage per Channel
VCM = 0.4V +IB (nA)–IB (nA)
SUPPLY VOLTAGE (V)1.8 2.3 2.8 3.3 3.8 4.3 4.8 5.3
–10
–8
–6
–4
–2
0
2
4
6
8
10
INPU
T BI
AS C
URRE
NT (n
A)
6258 G10
VS = ±2.5V
+IB, VCM = 2V–IB, VCM = 2V+IB, VCM = –2V–IB, VCM = –2V
TEMPERATURE (°C)–40 –25 –10 5 20 35 50 65 80 95 110 125
–20
–15
–10
–5
0
5
10
15
20
INPU
T BI
AS C
URRE
NT (n
A)
6262 G11
VS = 5VVCM = 0.4V
25°C–40°C125°C
SUPPLY VOLTAGE (V)0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
0
2
4
6
8
10
12
14
16
18
20
SUPP
LY C
URRE
NT (u
A)
6258 G12
VCM = 0.4VVS = 5VVS = 1.8V
TEMPERATURE (°C)–50 –20 10 40 70 100 130
0
5
10
15
20
25
SUPP
LY C
URRE
NT (µ
A)
6258 G13
–40°C/5V25°C/5V85°C/5V125°C/5V–40°C/1.8V25°C/1.8V85°C/1.8V125°C/1.8V
LOAD CURRENT (mA)0 0.5 1 1.5 2
–350
–300
–250
–200
–150
–100
–50
0
SATU
RATI
ON V
OLTA
GE F
ROM
TOP
RAI
L (m
V)
6258 G14
–40°C/5V25°C/5V85°C/5V125°C/5V–40°C/1.8V25°C/1.8V85°C/1.8V125°C/1.8V
LOAD CURRENT (mA)0 0.5 1 1.5 2
0
50
100
150
200
250
300
350
SATU
RATI
ON V
OLTA
GE F
ROM
BOT
TOM
RAI
L (m
V)
6258 G15
VCM = 0.4V
25°C125°C
–40°C
SUPPLY VOLTAGE (V)1.8 2.3 2.8 3.3 3.8 4.3 4.8 5.3
0
5
10
15
20
25
MAX
IMUM
SOU
RCIN
G CU
RREN
T (m
A)
6258 G16
VCM = 0.4V
SUPPLY VOLTAGE (V)1.8 2.3 2.8 3.3 3.8 4.3 4.8 5.3
0
5
10
15
20
25
30
MAX
IMUM
SIN
KING
CUR
RENT
(mA)
6259 G17
25°C125°C
–40°C
VS = ±2.5VVCM = 0.4VAV = 1
TIME (s)0 1 2 3 4 5 6 7 8 9 10
–5
–4
–3
–2
–1
0
1
2
3
4
5
NOIS
E VO
LTAG
E (µ
V)
6258 G18
LTC6258/LTC6259/LTC6260
6258960fa
9For more information www.linear.com/LTC6258
TYPICAL PERFORMANCE CHARACTERISTICS
Total Harmonic Distortion and Noise
Total Harmonic Distortion and Noise
Gain and Phase vs Frequency
Noise Voltage Density vs Frequency
Input Referred Current Noise vs Frequency
Slew Rate vs Supply Voltage
Common Mode Rejection Ratio vs Frequency
Power Supply Rejection Ratio vs Frequency
VS = ±2.5VVCM = 0V
FREQUENCY (Hz)1 10 100 1k 10k 100k 1M
0
50
100
150
200
250
300
350
400
450
500
INPU
T RE
FERR
ED V
OLTA
GE N
OISE
(nV/
√Hz)
6258 G19
VS = 2.5VVCM = 0V
FREQUENCY (MHz)0.1 1
0.01
0.1
1
10
INPU
T RE
FERR
ED C
URRE
NT N
OISE
(pA/
√Hz)
6258 G20
VS = ±0.9VVCM = 0VAV = 2RG = RF = 10kΩ
1kHz500Hz
VOUTP–P (V)0.01 0.1 1
0.01
0.1
1
THD+
N (%
)
6259 G21
VS = ±2.5VVCM = 0VAV = 2RG = RF = 10kΩ
1kHz500Hz
VOUTP-P (V)0.01 0.1 1 10
0.01
0.1
1
THD+
N (%
)
6258 G23
VS = ±2.5VVCM = 0V
GAINPHASE
FREQUENCY (Hz)10k 100k 1M 10M
–50
–40
–30
–20
–10
0
10
20
30
40
50
0
9
18
27
36
45
54
63
72
81
90
GAIN
(dB) PHASE
6258 G23
VSTEP = VS – 1VAV = –1RG=RF = 10kΩ
RISINGFALLING
SUPPLY VOLTAGE (V)1.8 2.6 3.4 4.2 5
0
0.1
0.2
0.3
0.4
0.5
SLEW
RAT
E (V
/µs)
6258 G24
VS = 5V
VCM = ±2.5VVCM = 0V
FREQUENCY (Hz)1k 10k 100k 1M 10M
0
10
20
30
40
50
60
70
80
90
100
CMRR
(dB)
6258 G25
VS = 5VVCM = 0.4V
FREQUENCY (Hz)100 1k 10k 100k 1M 10M
0
10
20
30
40
50
60
70
80
90
100
PSRR
(dB)
6258 G26
VS = ±2.5VVCM = 0VAV = 1VIN = ±2V
CAPACITIVE LOAD (nF)0.01 0.1 1 10 1000
1
2
3
4
5
OVER
SHOO
T (%
)
6258 G27
Capacitive Load Handling Overshoot vs Capacitive Load
LTC6258/LTC6259/LTC6260
106258960fa
For more information www.linear.com/LTC6258
TYPICAL PERFORMANCE CHARACTERISTICS
Small-Signal Response
Small-Signal Response
Electromagnetic Interference Rejection Ratio
Large-Signal Response
Supply Current vs SHDN Pin Voltage
Supply Current vs SHDN Pin Voltage
Large-Signal Response
Output Impedance vs Frequency
VS = ±2.5VAV = 1RLOAD = 100kΩ
10pF100pF1nF10nF100nF
TIME (µs)0 200 400 600 800 1000
–2.5
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
2.5
VOLT
AGE
(V)
6258 G28
VS = ±2.5VAV = 1RLOAD = 100kΩ
CLOAD = 10pFCLOAD = 100pFCLOAD = 1nFCLOAD = 10nFCLOAD = 100nF
TIME (µs)0 200 400 600 800 1000
–50
–40
–30
–20
–10
0
10
20
30
40
50
VOLT
AGE
(mV)
6259 G30
VS = ±0.9VAV = 1RLOAD = 100kΩ
CLOAD = 10pFCLOAD = 100pFCLOAD = 1nFCLOAD = 10nFCLOAD = 100nF
TIME (µs)0 200 400 600 800 1000
–1.0
–0.8
–0.6
–0.4
–0.2
0.0
0.2
0.4
0.6
0.8
1.0
VOLT
AGE
(V)
6258 G30
VS = ±0.9VAV = 1RLOAD = 100kΩ
CLOAD = 10pFCLOAD = 100pFCLOAD = 1nFCLOAD = 10nFCLOAD = 100nF
TIME (µs)0 200 400 600 800 1000
–50
–40
–30
–20
–10
0
10
20
30
40
50
VOLT
AGE
(mV)
6258 G31
VS = ±2.5VVCM = 0V
AV = 10AV = 1
FREQUENCY (kHz)0.01 0.1 1 10
0.1
1
10
100
1k
10k
OUTP
UT IM
PEDA
NCE
(Ω)
6258 G32
VS = 5VVCM = 0.4V
TA = 125°CTA = 25°CTA = –40°C
VSHDN (V)0 0.4 0.8 1.2 1.6 2
0
5
10
15
20
25
SUPP
LY C
URRE
NT (µ
A)
6258 G33
VS = 1.8VVCM = 0.4V
TA = 125°CTA = 25°CTA = –40°C
VSHDN (V)0 0.4 0.8 1.2 1.6 2
0
5
10
15
20
25
SUPP
LY C
URRE
NT (µ
A)
6258 G34
VS = 2.5VVCM = 0VINPUT POWER = –10dBm
+IN–IN
FREQUENCY (MHz)10 100 1000 10000
0
10
20
30
40
50
60
70
80
90
100
EMI R
EJEC
TION
RAT
IO (d
B)
6258 G35
LTC6258/LTC6259/LTC6260
6258960fa
11For more information www.linear.com/LTC6258
PIN FUNCTIONS–IN: Inverting Input of the Amplifier. Voltage range of this pin can go from V– – 0.1V to V+ + 0.1V.
+IN: Noninverting Input of Amplifier. This pin has the same voltage range as –IN.
V+: Positive Power Supply. Typically the voltage is from 1.8V to 5.25V. Split supplies are possible as long as the voltage between V+ and V– is between 1.8V and 5.25V. A bypass capacitor of 0.1µF as close to the part as possible should be used between power supply pins or between supply pins and ground.
V–: Negative Power Supply. It is normally tied to ground. It can also be tied to a voltage other than ground as long as the voltage between V+ and V– is from 1.8V to 5.25V. If it is not connected to ground, bypass it with a capacitor of 0.1µF as close to the part as possible.
SHDN: Active Low Shutdown. Shutdown threshold is 0.6V above negative rail. If left unconnected, the amplifier will be on.
OUT: Amplifier Output. Rail-to rail amplifier output capable of delivering 4mA.
LTC6258/LTC6259/LTC6260
126258960fa
For more information www.linear.com/LTC6258
SIMPLIFIED SCHEMATIC
Figure 1. LTC6258/LTC6259/LTC6260 Simplified Schematic
+I2
Q17 Q18
ESDD4
–IN
+IN
V–
Q3Q4
Q6
Q8
R2
R4
Q9
Q12
R1
R3R6
Q7
Q16
ESDD3
V+
ESDD1
V+
ESDD2
V–
V–
V+
SHDN
V–
D8
D7
ESDD5
ESDD6
D6
D5
Q2
Q5 VBIAS
Q1
+I1
I3
Q19
R5
Q11
Q10
Q13
Q15
OUT
C2
C1
+
Q14
CC
BUFFER ANDOUTPUT BIAS
6258960 F01
LOGIC
LTC6258/LTC6259/LTC6260
6258960fa
13For more information www.linear.com/LTC6258
OPERATIONThe LTC6258 family input signal range extends beyond the negative and positive power supplies. Figure 1 depicts a Simplified Schematic of the amplifier. The input stage is comprised of two differential amplifiers, a PNP stage Q1/Q2 and NPN stage Q3/Q4 that are active over different ranges of common mode input voltage. The PNP stage is active between the negative power supply to approxi-mately 1V below the positive supply. As the input voltage approaches the positive supply, transistor Q5 will steer the tail current I1 to the current mirror Q6/Q7, activating the NPN differential pair and the PNP pair becomes inactive for the remaining input common mode range. Also for the
input stage, devices Q17, Q18 and Q19 act to cancel the bias current of the PNP input pair. When Q1/Q2 is active, the current in Q16 is controlled to be the same as the current Q1/Q2. Thus, the base current of Q16 is normally equal to the base current of the input devices of Q1/Q2. Similar circuitry (not shown) is used to cancel the base current of Q3/Q4. The buffer and output bias stage uses a special compensation technique to take full advantage of the process technology to drive high capacitive loads. The common emitter topology of Q14/Q15 enables the output to swing from rail to rail.
LTC6258/LTC6259/LTC6260
146258960fa
For more information www.linear.com/LTC6258
APPLICATIONS INFORMATIONLow Supply Voltage and Low Power Consumption
The LTC6258 family of operational amplifiers can oper-ate with power supply voltages from 1.8V to 5.25V. Each amplifier draws 20µA. The low supply voltage capability and low supply current are ideal for portable applications.
High Capacitive Load Driving Capability and Wide Bandwidth
The LTC6258 family is optimized for wide bandwidth low power applications. They have a high gain-bandwidth to power ratio and are unity gain stable. When the load capacitance increases, the increased capacitance at the output pushes the non-dominant pole to lower frequency in the open loop frequency response, worsening the phase and gain margin. The LTC6258 family are designed to directly drive up to 100nF of capacitive load in unity gain configuration (see Typical Performance Characteristics, Capacitive Load Handling).
Low Input Referred Noise
The LTC6258 family provides a low input referred noise of 38nV/√Hz at 1kHz. The average noise voltage density over a 100kHz bandwidth is less than 80nV/√Hz. The LTC6258 family is ideal for low noise and low power signal process-ing applications.
Low Input Offset Voltage
The LTC6258 family has a low offset voltage of 400μV, which is essential for precision applications. The offset voltage is trimmed with a proprietary trim algorithm to ensure low offset voltage over the entire common mode voltage range.
Low Input Bias Current
The LTC6258 family uses a bias current cancellation circuit to compensate for the base current of the input transistors. When the input common mode voltage is within 200mV of either rail, the bias cancellation circuit is no longer active. For common mode voltages ranging from 0.2V above the negative supply to 0.2V below the positive supply, the low input bias current allows the amplifiers to be used in applications with high resistance sources.
Ground Sensing and Rail to Rail Output
The LTC6258 family delivers over 4mA of output drive current. The output stage is a rail-to-rail topology that is capable of swinging to within 300mV of either rail. If output swing to the negative rail is required, an external pull down resistor to a negative supply can be added. For 5V/0V op amp supplies, a pull down resistor of 10k to –2V will allow a ‘true zero’ output swing. In this case, the output can swing all the way to the bottom rail while maintaining 45dB of open loop gain. Since the inputs can go 100mV beyond either rail, the op amp can easily perform ‘true ground’ sensing.
The maximum output current is a function of total supply voltage. As the supply voltage to the amplifier increases, the maximum output current also increases. Attention must be paid to keep the junction temperature of the IC below 150°C when the output is in continuous short-circuit. The output of the amplifier has reverse-biased diodes con-nected to each supply. The output should not be forced more than 0.5V beyond either supply, otherwise current will flow through these diodes.
EMI Rejection
Electromagnetic interference (EMI) rejection is built into the LTC6258 op amp family. Rejection is measured by injecting 200mVP-P (–10dBm) RF signal into the pins and measuring the offset change (delta_VOS). The rejection ratio is calculated as 20log (100mV/delta_VOS).
Input Protection and Output Overdrive
To prevent breakdown of the input transistors, the input stages are protected against a large differential input voltage by two pairs of back-to-back diodes, D5 to D8. If the differential input voltage exceeds 1.4V, the current in these diodes must be limited to less than 10mA. These amplifiers are not intended for open loop applications such as comparators. When the output stage is overdriven, internal limiting circuitry is activated to improve overdrive recovery. In some applications, this circuitry may draw as much as 1mA supply current.
LTC6258/LTC6259/LTC6260
6258960fa
15For more information www.linear.com/LTC6258
ESD
The LTC6258 family has reverse-biased ESD protection diodes on all inputs and output as shown in Figure 1.
Supply Voltage Ramping
Fast ramping of the supply voltage can cause a current glitch in the internal ESD protection circuits. Depending on the supply inductance, this could result in a supply volt-age transient that exceeds the maximum rating. A supply voltage ramp time of greater than 1ms is recommended.
Feedback Components
Care must be taken to ensure that the pole formed by the feedback resistors and the parasitic capacitance at the inverting input does not degrade stability. For example, in a gain of +2 configuration with gain and feedback resis-tors of 100k, a poorly designed circuit board layout with parasitic capacitance of 5pF (part +PC board) at the ampli-fier’s inverting input will cause the amplifier to oscillate due to a pole formed at 640kHz. An additional capacitor of 4.7pF across the feedback resistor as shown in Figure 2 will eliminate any ringing or oscillation.
Shutdown
The single and dual versions have package options with SHDN pins that can shut down the amplifier to less than 7µA supply current. The SHDN pin voltage needs to be within 0.6V of V– for the amplifier to shut down. During shutdown, the output is in a high output impedance state. When left floating, the SHDN pin is internally pulled up to the positive supply and the amplifier remains enabled.
100k
100k
4.7pF
CPAR VOUT
VIN 6258960 F02
+
–LTC6258
Figure 2.
Figure 3a. 10kHz Bandpass Filter
Figure 3b. Frequency Response of 10kHz Bandpass Filter of Figure 3a
APPLICATIONS INFORMATION
V+
V+
C14.7nF
C24.7nF
R221k
C34.7nF
R3562Ω
RA1499k
6258 F03a
RA2499k
CD11µF
R110k
R810kIN
OUT
CD20.1µF
U1
LT6259
–+
5dB/DIV
5dB
–45dB6258 F03b
Active Filter
The bandpass filter Figure 3a is AC-coupled to an input. As a result, LTC6259 input does not place a burden on the previous stage to develop an absolute common mode voltage. A simple resistor divider with RA1 and RA2 provides biasing for the LTC6259 inputs. Pegging the op amp inputs to a fixed voltage helps to reduce distortion that might arise with moving common mode. This filter is centered at 10kHz. The exact resistance and capacitance values can be tweaked upwards or downwards, depending on whether lowest resistor noise or lowest total supply current is more important.
LTC6258/LTC6259/LTC6260
166258960fa
For more information www.linear.com/LTC6258
Figure 4b. Low Power Sine Generator
Figure 4c. FFT
Figure 4a. Low Power Squarewave - Sinewave Oscillator
APPLICATIONS INFORMATION
Low Power Sine Wave Generator
A low power sine wave generator can be derived by driving a square wave into the bandpass filter. A complete schematic is shown in Figure 4a. The LTC6992-1 easily configures as a 50% duty cycle 10kHz square wave, and can drive the relatively benign loading seen in the bandpass filter.
Figures 4b and 4c show the LTC6992-1 output and bandpass filter output. THD of the sine wave is –30.5 dBc. Note, even harmonics that appear in the distortion products of the filtered output already appear in the source square wave.
Low Noise Reference
The LT6656 is a 1µA precision series voltage reference. Yet with low power comes low drive current capability and higher noise. The LTC6259 can be used as a buf-fer that follows a filter to enhance the utilization of the LT6656 in low power applications. Figure 5a shows such a configuration. First a very low cutoff frequency follows the LT6656 output (RIN1 and CIN1, lower than 5Hz cutoff). Choice of filter resistor RIN1 is such that the bias current in the LTC6259, multiplied by the resistance value, is lower than the nominal offset voltage of the op amp. CIN1 can be larger or smaller, with more or less filtering accord-ingly. The voltage withstanding requirement of CIN1 is low, resulting in large capacitance in a small volume.
V+
V+
4.7nF
4.7nF
21k
4.7nF
154k 182k
976k 0.1µF154k562Ω
499k
6258 F04a
499k1µF
10k 10kMOD
LTC6992-1GND
SET
OUT
V+
DIV
OUT
0.1µF
LT6258
–+
V+
50µs/Div0
1.0
2.0
3.0
4.0
5.0
LTC6
992–
1 OU
TPUT
(V)
6258 F04b
FILTERED OUTPUTSQUARE WAVE
FREQUENCY (kHz)0 10 20 30 40 50 60 70 80 90 100
–120
–100
–80
–60
–40
–20
0
20
AMPL
ITUD
E (d
B)
6258 F04c
LTC6258/LTC6259/LTC6260
6258960fa
17For more information www.linear.com/LTC6258
APPLICATIONS INFORMATION
–+
5V
V+OUT
LTC6258
6258960 F05a
22µF22µF
RIN12.7k
22µFIN OUT
GND
LT6656
Figure 5a. Low Noise Reference Use LT6656 for a Low Current Starting Reference
Figure 5b. Noise Density, Reference Buffer
Figure 5c. Reference Buffer Transient Response
* 2.7k + 22µF FILTER
OP AMP, 44µF CLOADOP AMPFILTERED REFERENCEREFERENCE OUTPUTINSTRUMENT ONLY
FREQUENCY (kHz)0.01 0.1 1 10 1000
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
NOIS
E DE
NSIT
Y (n
Vrm
s/rt(
Hz))
6258 F05b
This circuit takes advantage of the ability of the LTC6259 to drive large capacitive loads. Use of a large output capacitor attached to the LT6659 enables significant bypassing of follow-on circuits that use the reference voltage. In total, the combination of LT6656 and LTC6259, in this configuration, develops a reference voltage, with low noise, at low power, and with appreciably large available bypass capacitance.
Voltage spectral noise densities are shown in Figure 5b. Larger noise from the reference below 10kHz noticeably drops down once a filter (RIN1 and CIN1) follow the refer-ence. The op amp, configured in unity gain, with a large 44µF load, remains stable and contributes only a small amount of low frequency noise. Figure 5c shows the tran-sient response of the combination of RIN1-CIN1 filter and op amp circuit, with and without the 44µF output capacitor.
Figure 5c shows the time domain response of the refer-ence buffer.
The total measured supply current consumption is 21µA.
Analog LED Control
Figure 6a shows a voltage controlled LED drive circuit. When VIN is at 0V, the op amp supply current is nominally 20μA. The offset, for example, could be 450µV, appears across R1, inducing a 0.45mA current in the LED. Some applications want a guaranteed zero LED current at VIN = 0, and this is the purpose of R5. R5 forces 2.5μA current through R7, creating a negative 0.6mV sense offset. This offset guarantees a zero LED current.
INPUTNO 44µF OUTPUT CAPADD 44µF OUTPUT CAP
200ms/Div1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
VOLT
S (V
)
6258 F05c
LTC6258/LTC6259/LTC6260
186258960fa
For more information www.linear.com/LTC6258
APPLICATIONS INFORMATION
Figure 6a. Lower Power LED Driver with Voltage Command
Figure 6b. LED Current
–+
D1D
M12N7002
R11Ω
R6100k
R7237Ω
R451Ω
R52M
LTC6258
5V
R32.2k
R297.6k
VIN
C1100nF
6258 F06a
C210nF
VG
Indeed, the circuit works nicely. Once the input voltage is near 0, the LED current output is 0 and the total supply current is 20µA. Gain from the input voltage to LED cur-rent is 0.022A/V, as can be taken from the R2/R3 voltage divider and the sense resistor value.
LED Current= VIN
R1•
R3R2+R3
Self-Oscillating LED Driver
Taking the circuit of the above application a step further, the circuit of Figure 7a combines edge detection with use of the shutdown pin of the LTC6259. R2 and R3 bring in a divided down copy of the supply voltage as a reference into the positive terminal. The op amp forces this voltage on the sense resistor RSENSE in “LED ON” operation. In that sense this circuit is similar to the one above.
20 µA SUPPLY WHEN LED OFF
MEASUREDCALCULATED
INPUT VOLTAGE (V)0 1 2 3 4 5
0
20
40
60
80
100
LED
CURR
ENT
(mA)
6258 F06b
However, whereas the previous circuit assumes an always-on operation mode, this new circuit hijacks the shutdown pin. C2 can AC couple fast action signals into the signal VC. Hence when the gate voltage VG increases when “LED ON” begins, VC will suddenly rise. VC connects to the shutdown pin; a rising edge on the shutdown pin enables the LTC6259, which is already active, to stay on. However, M3 is also on while M1 is on, and as a result will work with R9 to charge C2 slowly until VC falls below the shutdown threshold. At that moment, the active low shutdown kicks in, and the LTC6259 turns off. A negative falling VG voltage again feeds through C2, and a falling VC and hence a falling shutdown pin voltage keeps the circuit in an “LED OFF” state for some time. M3 turns off, and C2 discharges until VC is high enough to reactivate the LTC6259.
It may seem a bit odd to develop such a circuit when a microprocessor or a LTC6992 can provide on-off capabil-ity in combination with a single MOSFET and resistor. The problem with those circuits, however, is the lack of control over the LED current. In the circuit of this application, a voltage is controlled across a sense resistor. There is no dependence on the LED voltage in how much current drives the LED. And generation of the on-off, or blinking, comes with the addition of only a handful of low cost components.
LTC6258/LTC6259/LTC6260
6258960fa
19For more information www.linear.com/LTC6258
APPLICATIONS INFORMATION
It is interesting to note that the LED current depends on the supply in this implementation in as much as the supply feeds through R2 and R3 to create a reference. The supply also figures into the time of the on and off cycle since the supply powers the edge detection and relaxation part of the circuitry. When the supply falls, the LED current drops and the cycle time increases. This change of behavior can help in battery powered LED blinking applications to predict end of life.
The figure shows the sense resistor voltage (red) and the shutdown pin voltage (blue). The shutdown voltage is tied to VC; the gate drive couples through C2 as already described.
Components RF and CF may apparently slow edges down greatly. Adding this much delay is not essential, but it can help to smooth out any hiccups that occur when the part goes through a startup sequence after the shutdown pin goes inactive. 47µs as a time constant is insignificant in the time scale of the blinking (10’s or 100’s of ms). The 47µs is much smaller than any time constant associated with C2 and its resistors.
VG
VG
VC
VC
R451Ω M1
2N7002
LED
D
RSENSE10Ω
R2275k
R315k
C11nF
C21µF
RGATE10k
R51M
R81M
M32N7002
6258 F07a
R7470k
R9140k
U2
LTC6258RF
100Ω
CF470nF
5V
–+
Figure 7a. LED Driver with Self-Oscillation
Figure 7b. LED Blinker Circuit
50ms/Div–60.0
0
60.0
120.0
180.0
240.0
300.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
SENS
E RE
SIST
OR V
OLTA
GE (m
V) SHUTDOWN PIN VOLTAGE (V)
6258 F07b
LTC6258/LTC6259/LTC6260
206258960fa
For more information www.linear.com/LTC6258
PACKAGE DESCRIPTIONPlease refer to http://www.linear.com/product/LTCLTC6258#packaging for the most recent package drawings.
1.50 – 1.75(NOTE 4)
2.80 BSC
0.30 – 0.45 6 PLCS (NOTE 3)
DATUM ‘A’
0.09 – 0.20(NOTE 3) S6 TSOT-23 0302
2.90 BSC(NOTE 4)
0.95 BSC
1.90 BSC
0.80 – 0.90
1.00 MAX0.01 – 0.10
0.20 BSC
0.30 – 0.50 REF
PIN ONE ID
NOTE:1. DIMENSIONS ARE IN MILLIMETERS2. DRAWING NOT TO SCALE3. DIMENSIONS ARE INCLUSIVE OF PLATING4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR5. MOLD FLASH SHALL NOT EXCEED 0.254mm6. JEDEC PACKAGE REFERENCE IS MO-193
3.85 MAX
0.62MAX
0.95REF
RECOMMENDED SOLDER PAD LAYOUTPER IPC CALCULATOR
1.4 MIN2.62 REF
1.22 REF
S6 Package6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
LTC6258/LTC6259/LTC6260
6258960fa
21For more information www.linear.com/LTC6258
PACKAGE DESCRIPTION
1.50 – 1.75(NOTE 4)
2.80 BSC
0.22 – 0.36 8 PLCS (NOTE 3)
DATUM ‘A’
0.09 – 0.20(NOTE 3)
TS8 TSOT-23 0710 REV A
2.90 BSC(NOTE 4)
0.65 BSC
1.95 BSC
0.80 – 0.90
1.00 MAX0.01 – 0.10
0.20 BSC
0.30 – 0.50 REF
PIN ONE ID
NOTE:1. DIMENSIONS ARE IN MILLIMETERS2. DRAWING NOT TO SCALE3. DIMENSIONS ARE INCLUSIVE OF PLATING4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR5. MOLD FLASH SHALL NOT EXCEED 0.254mm6. JEDEC PACKAGE REFERENCE IS MO-193
3.85 MAX
0.40MAX
0.65REF
RECOMMENDED SOLDER PAD LAYOUTPER IPC CALCULATOR
1.4 MIN2.62 REF
1.22 REF
TS8 Package8-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1637 Rev A)
Please refer to http://www.linear.com/product/LTC6259#packaging for the most recent package drawings.
LTC6258/LTC6259/LTC6260
226258960fa
For more information www.linear.com/LTC6258
PACKAGE DESCRIPTIONPlease refer to http://www.linear.com/product/LTC6259#packaging for the most recent package drawings.
MSOP (MS8) 0213 REV G
0.53 ±0.152(.021 ±.006)
SEATINGPLANE
NOTE:1. DIMENSIONS IN MILLIMETER/(INCH)2. DRAWING NOT TO SCALE3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.18(.007)
0.254(.010)
1.10(.043)MAX
0.22 – 0.38(.009 – .015)
TYP
0.1016 ±0.0508(.004 ±.002)
0.86(.034)REF
0.65(.0256)
BSC
0° – 6° TYP
DETAIL “A”
DETAIL “A”
GAUGE PLANE
1 2 3 4
4.90 ±0.152(.193 ±.006)
8 7 6 5
3.00 ±0.102(.118 ±.004)
(NOTE 3)
3.00 ±0.102(.118 ±.004)
(NOTE 4)
0.52(.0205)
REF
5.10(.201)MIN
3.20 – 3.45(.126 – .136)
0.889 ±0.127(.035 ±.005)
RECOMMENDED SOLDER PAD LAYOUT
0.42 ± 0.038(.0165 ±.0015)
TYP
0.65(.0256)
BSC
MS8 Package8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660 Rev G)
LTC6258/LTC6259/LTC6260
6258960fa
23For more information www.linear.com/LTC6258
PACKAGE DESCRIPTIONPlease refer to http://www.linear.com/product/LTC6259#packaging for the most recent package drawings.
MSOP (MS) 0213 REV F
0.53 ±0.152(.021 ±.006)
SEATINGPLANE
0.18(.007)
1.10(.043)MAX
0.17 – 0.27(.007 – .011)
TYP
0.86(.034)REF
0.50(.0197)
BSC
1 2 3 4 5
4.90 ±0.152(.193 ±.006)
0.497 ±0.076(.0196 ±.003)
REF8910 7 6
3.00 ±0.102(.118 ±.004)
(NOTE 3)
3.00 ±0.102(.118 ±.004)
(NOTE 4)
NOTE:1. DIMENSIONS IN MILLIMETER/(INCH)2. DRAWING NOT TO SCALE3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.254(.010) 0° – 6° TYP
DETAIL “A”
DETAIL “A”
GAUGE PLANE
5.10(.201)MIN
3.20 – 3.45(.126 – .136)
0.889 ±0.127(.035 ±.005)
RECOMMENDED SOLDER PAD LAYOUT
0.305 ±0.038(.0120 ±.0015)
TYP
0.50(.0197)
BSC
0.1016 ±0.0508(.004 ±.002)
MS Package10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661 Rev F)
LTC6258/LTC6259/LTC6260
246258960fa
For more information www.linear.com/LTC6258
PACKAGE DESCRIPTIONPlease refer to http://www.linear.com/product/LTC6260#packaging for the most recent package drawings.
MSOP (MS16) 0213 REV A
0.53 ±0.152(.021 ±.006)
SEATINGPLANE
0.18(.007)
1.10(.043)MAX
0.17 – 0.27(.007 – .011)
TYP
0.86(.034)REF
0.50(.0197)
BSC
16151413121110
1 2 3 4 5 6 7 8
9
NOTE:1. DIMENSIONS IN MILLIMETER/(INCH)2. DRAWING NOT TO SCALE3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.254(.010) 0° – 6° TYP
DETAIL “A”
DETAIL “A”
GAUGE PLANE
5.10(.201)MIN
3.20 – 3.45(.126 – .136)
0.889 ±0.127(.035 ±.005)
RECOMMENDED SOLDER PAD LAYOUT
0.305 ±0.038(.0120 ±.0015)
TYP
0.50(.0197)
BSC
4.039 ±0.102(.159 ±.004)
(NOTE 3)
0.1016 ±0.0508(.004 ±.002)
3.00 ±0.102(.118 ±.004)
(NOTE 4)
0.280 ±0.076(.011 ±.003)
REF
4.90 ±0.152(.193 ±.006)
MS Package16-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1669 Rev A)
LTC6258/LTC6259/LTC6260
6258960fa
25For more information www.linear.com/LTC6258
PACKAGE DESCRIPTIONPlease refer to http://www.linear.com/product/LTC6258#packaging for the most recent package drawings.
2.00 ±0.10(4 SIDES)
NOTE:1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WCCD-2)2. DRAWING NOT TO SCALE3. ALL DIMENSIONS ARE IN MILLIMETERS4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
0.40 ±0.10
BOTTOM VIEW—EXPOSED PAD
0.60 ±0.10(2 SIDES)
0.75 ±0.05
R = 0.125TYP
R = 0.05TYP
1.37 ±0.10(2 SIDES)
13
64
PIN 1 BARTOP MARK
(SEE NOTE 6)
0.200 REF
0.00 – 0.05
(DC6) DFN REV C 0915
0.25 ±0.050.50 BSC
0.25 ±0.05
1.37 ±0.10(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
0.60 ±0.10(2 SIDES)
1.15 ±0.05
0.70 ±0.05
2.55 ±0.05
PACKAGEOUTLINE
0.50 BSC
PIN 1 NOTCH R = 0.20 OR 0.25 × 45° CHAMFER
DC6 Package6-Lead Plastic DFN (2mm × 2mm)
(Reference LTC DWG # 05-08-1703 Rev C)
LTC6258/LTC6259/LTC6260
266258960fa
For more information www.linear.com/LTC6258
PACKAGE DESCRIPTIONPlease refer to http://www.linear.com/product/LTC6259#packaging for the most recent package drawings.
2.00 ±0.10(4 SIDES)
NOTE:1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE2. DRAWING NOT TO SCALE3. ALL DIMENSIONS ARE IN MILLIMETERS4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
0.40 ±0.10
BOTTOM VIEW—EXPOSED PAD
0.64 ±0.10(2 SIDES)
0.75 ±0.05
R = 0.115TYP
R = 0.05TYP
1.37 ±0.10(2 SIDES)
14
85
PIN 1 BARTOP MARK
(SEE NOTE 6)
0.200 REF
0.00 – 0.05
(DC8) DFN 0409 REVA
0.23 ±0.050.45 BSC
0.25 ±0.05
1.37 ±0.05(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONSAPPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
0.64 ±0.05(2 SIDES)
1.15 ±0.05
0.70 ±0.05
2.55 ±0.05
PACKAGEOUTLINE
0.45 BSC
PIN 1 NOTCH R = 0.20 OR 0.25 × 45° CHAMFER
DC8 Package8-Lead Plastic DFN (2mm × 2mm)
(Reference LTC DWG # 05-08-1719 Rev A)
LTC6258/LTC6259/LTC6260
6258960fa
27For more information www.linear.com/LTC6258
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
REVISION HISTORYREV DATE DESCRIPTION PAGE NUMBER
A 04/17 Added SOT-23 package. 1, 2, 3, 20
LTC6258/LTC6259/LTC6260
286258960fa
For more information www.linear.com/LTC6258 LINEAR TECHNOLOGY CORPORATION 2017
LT 0417 REV A • PRINTED IN USAwww.linear.com/LTC6258
TYPICAL APPLICATION
RELATED PARTSPART NUMBER DESCRIPTION COMMENTS
LTC6255/LTC6256/LTC6257
6.5MHz, 65µA Power Efficient RR Op Amp 6.5MHz, 65µA, RR IN/OUT, 1.8V to 5.25V
LTC6261/LTC6262/LTC6263
30MHz, 240µA Power Efficient RR Op Amp 30MHz, 240µA, RR IN/OUT, 1.8V to 5.25V
LTC6246/LTC6247/LTC6248
180MHz, 1mA, Power Efficient Rail-to-Rail Op Amps 180MHz GBW, 1mA, 500μV VOS, RR In/Out, 2.5V to 5.25V, 90V/µs Slew Rate
LT1498/LT1499 10MHz, 6V/µs, Dual/Quad,Rail-to-Rail Input and Output, Precision C-Load Op Amps
10MHz GBW, 1.7mA, 475μV VOS, RR In/Out, 2.2V to ±15V, 10nF CLOAD
LTC6081/LTC6082 Precision Dual/Quad CMOS Rail-to-Rail Input/Output Amplifiers
3.6MHz GBW, 330μA, 70μV VOS, RR In/Out, 2.7V to 5.5V, 100dB CMRR
LTC2050/LTC2051/LTC2052
Zero-Drift Operational Amplifiers in SOT-23 3MHz GBW, 800μA, 3μV VOS, V– to V+ – 1V In, RR Out, 2.7V to 6V, 130dB CMRR/PSRR
LTC1050/LTC1051/LTC1052
Precision Zero-Drift, Operational Amplifierwith Internal Capacitors
2.5MHz GBW, 1mA, 5μV VOS, V– to V+ – 2.3V In, RR Out, 4.75V to 16V, 120dB CMRR, 125dB PSRR
LTC6084/LTC6085 Dual/Quad 1.5MHz, Rail-to-Rail, CMOS Amplifiers 1.5MHz GBW, 110μA, 750μV VOS, RR In/Out, 2.5V to 5.5V
LT1783 1.25MHz, Over-The-Top® Micropower, Rail-to-Rail Input and Output Op Amp in SOT-23
1.25MHz GBW, 300μA, 800μV VOS, RR In/Out, 2.5V to 18V
LT1637/LT1638/LT1639
1.1MHz, 0.4V/μs Over-The-Top Micropower, Rail-to-Rail Input and Output Op Amps
1.1MHz GBW, 250μA, 350μV VOS, RR In/Out, 2.7V to 44V, 110dB CMRR
LTC2054/LTC2055 Single/Dual Micropower Zero-Drift Operational Amplifiers 500kHz GBW, 150μA, 3μV VOS, V– to V+ – 0.5V In, RR Out, 2.7V to 6V
LT6010/LT6011/LT6012
135μA, 14nV/√Hz, Rail-to-Rail Output Precision Op Amp with Shutdown
330kHz GBW, 135μA, 35μV VOS, V– + 1.0V to V+ – 1.2V In, RR Out, 2.7V to 36V
LT1782 Micropower, Over-The-Top, SOT-23, Rail-to-Rail Input and Output Op Amp
200kHz GBW, 55μA, 800μV VOS, RR In/Out, 2.5V to 18V
LT1636 Over-The-Top, Micropower Rail-to-Rail, Input and Output Op Amp
200kHz GBW, 50μA, 225μV VOS, RR In/Out, 2.7V to 44V, –40°C to 125°C
LT1490A/LT1491A Dual/Quad Over-The-Top, Micropower Rail-to-Rail Input and Output Op Amps
200kHz GBW, 50μA, 500μV VOS, RR In/Out, 2V to 44V
LT2178/LT2179 17μA Max, Dual and Quad, Single Supply, Precision Op Amps
85kHz GBW, 17μA, 70μV VOS, RR In/Out, 5V to 44V
LT6000/LT6001/LT6002
Single, Dual and Quad, 1.8V, 13μA Precision Rail-to-Rail Op Amps
50kHz GBW, 16μA , 600μV VOS(MAX), RR In/Out, 1.8V to 18V
VG
VG
VC
VC
R451Ω M1
2N7002
LED
D
RSENSE10Ω
R2275k
R315k
C11nF
C21µF
RGATE10k
R51M
R81M
M32N7002
6258 TA03
R7470k
R9140k
U2
LTC6258RF
100Ω
CF470nF
5V
–+
50ms/Div–60.0
0
60.0
120.0
180.0
240.0
300.0
–2.0
–1.0
0
1.0
2.0
3.0
4.0
SENS
E RE
SIST
OR V
OLTA
GE (m
V) SHUTDOWN PIN VOLTAGE (V)
6258 TA04
LED Driver with Self Oscillation LED Blinker Current