FACP FSCU VS WF FAA DH 2 E4.2 F FIRE ALARM PULL STATION. WALL MOUNTED 3 FT.-6 IN. ABOVE FLOOR. FIRE ALARM SIGNAL, SPEAKER AND FLASHING LIGHT, 6'-8" AFF. FIRE ALARM STROBE LIGHT, 6'-8" IN. MOUNTING HEIGHT. FIRE ALARM CONNECTION, HOOD EXTINGUISHING SYSTEM, SEE MECHANICAL DRAWINGS FOR LOCATION. INTERLOCK WITH SHUNT TRIP BREAKERS FOR EQUIPMENT UNDER HOOD. FIRE ALARM REMOTE LCD ANNUNCIATOR PANEL. FLUSH RECESSED WALL MOUNTED. FIRE ALARM DOOR HOLDER, WALL MOUNTED, CONSULT ARCHITECTURAL DRAWINGS TO DETERMINE TYPE REQUIRED. PROVIDE POWER FROM NEAREST RECEPTACLE CIRCUIT AND CONNECT TO FIRE ALARM SYSTEM. TAMPER SWITCH, FURNISHED AND INSTALLED WITH SPRINKLER SYSTEM. INTERLOCK WITH FIRE ALARM SYSTEM BY ELECTRICAL. FLOW SWITCH, FURNISHED AND INSTALLED WITH SPRINKLER SYSTEM. INTERLOCK WITH FIRE ALARM SYSTEM BY ELECTRICAL. FIRE ALARM SMOKE DETECTOR, CEILING MOUNTED. FIRE ALARM DUCT SMOKE DETECTOR LOCATED IN HVAC DUCT. FIRE ALARM CONTROL PANEL, SURFACE WALL MOUNTED. FIRE ALARM SIGNAL, HORN. 6 FT.-8 IN. MOUNTING HEIGHT. FIRE ALARM HEAT DETECTOR, 135 DEG, OPERATION. P WEATHER PROOF. FIRE ALARM STROBE LIGHT, CEILING MOUNTED. S M FIRE ALARM: H S WP IC AD AC S 2. COORDINATE MOUNTING HEIGHTS, DEVICE LOCATIONS & POWER/CONTROL REQUIREMENTS WITH ARCHITECTURAL DRAWINGS AND SYSTEM INSTALLER. INTRUSION DETECTION SYSTEM: CONDUIT SLEEVE: NUMBER & SIZE, (2)-2" FOR ALL CLASSROOMS, (1)-2" FOR ALL OFFICES, UNO CABLE TRAY: SIZE AS INDICATED, 18"W x 4"H TYP. INTERCOM SPEAKER: WEATHERPROOF WALL MOUNTED AT 96"AFF. MICROPHONE JACK: WALL MOUNTED AT 18" AFF, UNO. ENHANCED STAFF PHONE: WALL MOUNTED 48" AFF ADMINISTRATIVE DISPLAY PHONE: WALL MOUNT AT 48" AFF INTRUSION SYSTEM: KEY-PAD, MOUNT 48"AFF SECURITY ACCESS: MOUNT ABOVE CEILING AT ENTRY WAY INTRUSION DETECTION DEVICE: WALL MTD. ACCESS CONTROL SYSTEMS SEE DETAIL 1/T0.01 FOR POWER, POWER DISCONNECT, LOW VOLTAGE CABLING, BOXES AND CONDUIT REQUIREMENTS. REFER TO ARCHITECTURAL PLANS AND DOOR SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS. INTERCOM SPEAKER: 2' X 2' SQUARE CEILING MOUNTED COORDINATE MOUNTING HEIGHTS, DEVICE LOCATIONS & POWER/CONTROL REQUIREMENTS WITH ARCHITECTURAL DRAWINGS AND SYSTEM INSTALLER. SPEAKER SYSTEM: CABLING COMPONENTS: THE CONTRACTOR SHALL PROVIDE ROUGH-IN FOR ALL DEVICES AND WIRING. ROUGH-IN REQUIREMENTS ARE SPECIFIED IN SECTION 261010. VERIFY ADJACENCY TO CORRESPONDING POWER RECEPTACLES. OTHER DEVICES WHOSE LOCATIONS ARE NOT DEPENDENT ON RECEPTACLE PLACEMENT SHALL BE COORDINATED WITH SYSTEM INSTALLER. WALL MTD. TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING CEILING MTD. TELECOMMUNICATION JUNCTION BOX WALL MTD. TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING CEILING MTD. TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING CEILING OR WALL MTD. TELECOMMUNICATION JUNCTION BOX AND CONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING ROUGH-IN FOR LOW VOLTAGE SYSTEMS: SA K P J J O S O S OS W HD C PC XX-1 T M ABBREVIATIONS: LEGEND: LIGHTING FIXTURES: UPPERCASE LETTER ADJACENT TO FIXTURE DENOTES DESIGNATION PER THE LIGHTING FIXTURE SCHEDULE. LOWERCASE LETTER DENOTES SWITCHLEG. THE RESPECTIVE SWITCH WILL HAVE THE SAME DESTINATIONS. NUMERAL DENOTES BRANCH CIRCUIT CONNECTION. REFER TO THE FIXTURE SCHEDULE FOR THE SPECIFIC FIXTURE INFORMATION. EMERGENCY FIXTURES SHALL HAVE FACTORY INSTALLED INTERNAL BATTERIES, PER SPECIFICATIONS. NL SUFFIX ADJACENT TO FIXTURE TYPE DENOTES NIGHT LIGHT. DO NOT SWITCH THESE FIXTURES. NON- EMERGENCY EMERGENCY/ BATTERY BACKUP LIGHTING FIXTURE: LINEAR FLUORESCENT ELECTRICAL EQUIPMENT: REFER TO ONE-LINE DIAGRAM AND EQUIPMENT CONNECTION SCHEDULE FOR LOAD DATA USED AS THE BASIS OF DESIGN AND REQUIRED CONNECTIONS. VERIFY LOAD AND LOCATION WITH EQUIPMENT CUT-SHEETS AND INSTALLER. GENERAL NOTES: DEVICE IDENTIFIER TAGS: NUMERAL ADJACENT TO DEVICE DENOTES BRANCH CIRCUIT CONNECTION. IDENTIFIER TAGS ADJACENT TO DEVICES INDICATE: WIRING DEVICES: RECEPTACLES: NOMINAL MOUNTING HEIGHT OF RECEPTACLES SHALL BE 18" TO CENTER, UNO. IF APPLICABLE, ADJUST SO DEVICE COVER IS IN THE CENTER OF MASONRY COURSE NEAREST THAT HEIGHT. THE HEIGHT ESTABLISHED SHALL GOVERN FOR ALL BOX INSTALLATIONS, WHERE INSTALLED IN MASONRY OR FRAMED WALLS. SWITCHES: MOUNTING HEIGHT OF SWITCHES SHALL BE 48" NOMINAL, ADJUSTED IN THE SAME MANNER AS SPECIFIED ABOVE, FOR RECEPTACLES. LOWERCASE LETTER INDICATES SWITCHLEG CONNECTION. THE RESPECTIVE FIXTURE(S) WILL HAVE THE SAME DESIGNATION. BRANCH CIRCUITS: CONDUCTOR COUNTS ARE SHOWN ON THE HOMERUNS ONLY. CONTRACTOR SHALL DETERMINE COUNTS FOR INTERMEDIATE RUNS BASED ON THE MANNER IN WHICH THE CIRCUIT ELEMENTS ARE CONNECTED. REFER TO THE SPECIFICATION SECTIONS 262010, 262080, & 26030 FOR SPECIAL REQUIREMENTS. LA-1,3,5 MISCELLANEOUS COMPONENTS: 3 4 a K O LIGHTING FIXTURE: LINEAR FLUORESCENT LIGHTING FIXTURE: LINEAR FLUORESCENT LIGHTING FIXTURE: FLUORESCENT STRIP LIGHTING FIXTURE: FLUORESCENT, WALL MTD. DOWNLIGHT/SCONCE FIXTURE EXIT: UNIVERSAL MTD. DIRECTIONAL FIXTURES: EMERGENCY TYPE LIGHT TRACK: LENGTH AS SHOWN MOUNT ABOVE COUNTERTOP OR BACKSPLASH, 9" ABOVE WORK SURFACE TO CENTER MOUNT DEVICE AT HEIGHT INDICATED PROVIDE WEATHER-PROOF COVER RECEPTACLE: SIMPLEX RECEPTACLE: DUPLEX, TAMPER RESISTANT TYPE. RECEPTACLE: GROUND-FAULT-INTERRUPTING, TAMPER RESISTANT TYPE IN-SLAB FLOOR BOX: SEE SPECIFICATIONS RECEPTACLE: DRYER, 30 AMP, 120/250 VOLT RECEPTACLE: SPECIAL PURPOSE , COORDINATE NEMA RATING WITH SPECIFIED EQUIPMENT ELECTRIC WATER COOLER POWER CONNECTION, GFI OUTLET HAND DRYER POWER CONNECTION: COORDINATE MOUNTING HEIGHT W/ ARCHITECTURAL ELEVATIONS SEE HAND DRYER INSTALLATION DETAIL 1/E7.01. RECEPTACLE FOR CLOCK (RECESSED) WITH CLOCK HANGER AND CLOCK. COORDINATE MOUNTING HEIGHT & LOCATION WITH ARCHITECTURAL FLOOR PLAN AND ELEVATIONS RECEPTACLE: CEILING MOUNTED SWITCH: SINGLE-POLE SWITCH: THREE-WAY TYPE SWITCH: FOUR-WAY TYPE SWITCH: SUBSCRIPT THAT INDICATES CORRESPONDING FIXTURES THAT SWITCH CONTROLS SWITCH: KEY-OPERATED SWITCH: OVERRIDE OCCUPANCY SENSOR, CEILING MOUNTED OCCUPANCY SENSOR, CORNER MOUNTED OCCUPANCY SENSOR, WALL MOUNTED SWITCH: MOTOR RATED, WITHOUT OVERLOAD PROTECTION DISCONNECT SWITCH DRY-TYPE TRANSFORMER PANELBOARD: SURFACE MOUNTED EQUIPMENT AS NOTED, SEE ABBREVIATIONS, THIS SHEET PHOTOCELL: LOCATE UNDER EAVES, FACING NORTH, AVOID ANY OTHER OUTSIDE LIGHT SOURCE BRANCH CIRCUIT: CONCEALED BRANCH CIRCUIT: CONCEALED IN FLOOR SLAB BRANCH CIRCUIT: EXPOSED 'HOMERUN' TO PANEL: NUMBER OF HASH MARKS INDICATES QUANTITY OF No. 12 AWG UNGROUNDED CONDUCTORS IN 3/4" RACEWAY. GROUNDED CONDUCTORS (NEUTRALS) ARE NOT SHOWN - ONE DEDICATED NEUTRAL IS REQUIRED FOR EACH UNGROUNDED CONDUCTOR INSTALLED, SEE SPECIFICATIONS. EACH CONDUCTOR SHALL BE MIN. No. 12 AWG UNLESS NOTED OTHERWISE. JUNCTION BOX: MTD. ABOVE CEILING JUNCTION BOX: WALL MTD. 7. WHERE COMPLETE BRANCH CIRCUIT WIRING IS NOT SHOWN, PROVIDE ACCORDING TO HOMERUNS SHOWN AND CORRESPONDING CIRCUIT NUMBERS ADJACENT TO THE DEVICE OR FIXTURE. REFER TO THE SPECIFICATIONS FOR THE WIRING METHODS. BRANCH CIRCUIT RATINGS SHALL BE BASED ON OVERCURRENT DEVICE RATINGS SHOWN IN THE PANEL SCHEDULES. 8. REFER TO THE ELECTRICAL PANELBOARD SCHEDULES AND EQUIPMENT RATINGS & CONNECTIONS SCHEDULE FOR VOLTAGE, BRANCH CIRCUITS REQUIREMENTS, BREAKERS SIZES AND OTHER RELATED ELECTRICAL EQUIPMENT TO BE PROVIDED AND/OR INSTALLED BY THE ELECTRICAL CONTRACTOR. C XX" WP A AMPERES AFF ABOVE FINISHED FLOOR AFG ABOVE FINISHED GRADE AH AIR HANDLER AIC AMPERAGE INTERRUPT CAPABILITY ATU AIR TERMINAL UNIT A/V AUDIO/VISUAL AWG AMERICAN WIRE GAUGE BFG BELOW FINISHED GRADE B.E. BOTTOM EDGE C. CONDUIT CU CONDENSING UNIT DAH DUCTLESS AIR HANDLER DHP DUCTLESS HEAT PUMP DIA. DIAMETER V S V S VS VACANCY SENSOR, CEILING MOUNTED VACANCY SENSOR, CORNER MOUNTED VACANCY SENSOR, WALL MOUNTED THE ELECTRICAL DRAWINGS ARE ONLY PART OF THE CONTRACT DOCUMENTS. THE CONTRACTOR SHALL REVIEW ALL OF THE DRAWINGS AND SPECIFICATIONS FOR THEIR INTERRELATIONSHIP AND REQUIRED COORDINATION BETWEEN DISCIPLINES. SYMBOL WHERE SHOWN AT OR NEAR A ROOM INDICATES THAT ROOM IS SHOWN AS A TYPICAL LARGE SCALE. (2) INDICATES THE DETAIL NUMBER AND (E4.2) INDICATES THE SHEET NUMBER. ALL CONDUCTORS SHALL BE COPPER UNLESS NOTED WITH THE WORD "ALUMINUM" IN THE DESCRIPTION. EACH DOOR SHALL HAVE ONE 3/4"C. FROM DOOR FRAME TO DOOR CONTROLLER ENCLOSURE (ASSUME WITHIN 50' OF DOOR), ONE DEDICATED 20A, 120 VOLT CIRCUIT TO SAME CONTROLLER ENCLOSURE. PRIOR TO RUNNING ANY CONDUIT, COORDINATE LOCATIONS OF ALL WALL MOUNTED DEVICES WITH WALL MOUNTED ACOUSTICAL PANELS. SEE ARCHITECTURAL DRAWINGS FOR SPACES IN WHICH WALL PANELS ARE INSTALLED. PRIOR TO RUNNING CONDUIT, COORDINATE LOCATIONS OF ALL WALL MOUNTED DEVICES WITH WALL MOUNTED SAFETY PADS IN GYMNASIUM. 1. 3. 4. 5. 6. E.C.B. ENCLOSED CIRCUIT BREAKER EF EXHAUST FAN EH ELECTRIC HEATER EMCS ENERGY MANAGEMENT CONTROL UNIT FAAP FIRE ALARM ANNUNCIATOR PANEL FACP FIRE ALARM CONTROL PANEL G GROUND GFI GROUND-FAULT INTERRUPTING HP HORSE POWER HRVU HEAT RECOVERY VENTILATING UNIT HWCP HOT WATER CIRCULATING PUMP KCMIL KILO CIRCULAR MIL MAH MAKEUP AIR HEATER MB MAIN BREAKER MCA MINIMUM CIRCUIT AMPS MIN MINIMUM MOCP MAXIMUM OVERCURRENT PROTECTION MTD MOUNTED No. NUMBER NEC NATIONAL ELECTRIC CODE NTS NOT TO SCALE PIV POST INDICATOR VALVE RGS RIGID GALVANIZED STEEL RTU ROOFTOP UNIT SF SUPPLY FAN SPD SURGE PROTECTION DEVICE SWBD SWITCHBOARD TGB TELECOMMUNICATIONS GROUND BUS TMGB TELECOMMUNICATIONS MAIN GROUND BUS TTW THROUGH-THE-WALL HEAT PUMP TYP TYPICAL UH UNIT HEATER UNO UNLESS NOTED OTHERWISE V VOLTAGE W WATTAGE W/ WITH WH WATER HEATER WHP WALL-MOUNTED HEAT PUMP WP WEATHER PROOF XFMR TANSFORMER SMOKE DAMPER, 120V, PROVIDE POWER CONNECTION AND ALL NEEDED SMOKE DETECTION AND CONTROL MODULES AS REQUIRED BY NFPA 72 FOR PROPER OPERATION. SD FIRE ALARM REMOTE VOICE EVACUATION MICROPHONE FLUSH RECESSED WALL MOUNTED. MIC "C" DESIGNATION INDICATES CEILING MOUNTED. S SPEAKER - SEE DRAWINGS AND SPECIFICATIONS FOR TYPE. LA-1,3,5 'HOMERUN' TO PANEL FOR EQUIPMENT: SEE EQUIPMENT CONNECTION SCHEDULES FOR SIZE OF FEEDER AND NUMBER OF CONDUCTORS. V SWITCH: LOW VOLTAGE OVERRIDE SWITCH FOR VACANCY SENSOR. WHERE MULTIPLE SUBSCRIPTS ARE INDICATED ("ab" FOR EXAMPLE) PROVIDE A PUSHBUTTON FOR EACH CORRESPONDING GROUP OF FIXTURES TO BE CONTROLLED (2 BUTTON SWITCH FOR "ab" FOR EXAMPLE). THE PUSHBUTTONS SHALL BE MOUNTED UNDER A SINGLE GANG FACEPLATE. D SWITCH: DIMMER TYPE. DIMMER SHALL BE COMPATIBLE WITH BALLAST INSTALLED. PROVIDE ALL LOW VOLTAGE CABLING AND CONNECTIONS FOR 0 TO 10 VOLT DIMMING. FIRE ALARM CARBON MONOXIDE DETECTOR. O S HB OCCUPANCY SENSOR, CEILING MOUNTED HIGHBAY TYPE SCENE CONTROLLER STARTER/DISCONNECT SWITCH. SEE PLAN FOR SIZE, SEE SPECIFICATIONS FOR TYPE. 6 6 6 6 6 6 T PROFESSIONAL N E E R I G N E S I G E R E R E D No. 26308 I G R O E G A A W R. L N E R R A W NORTH 517 EAST CONGRESS STREET SAVANNAH, GEORGIA 31401 tel 912.234.6318 fax 912.236.8414 cogdellmendrala.com PROJECT CONSULTANTS: SEAL: SHEET TITLE: ARCH. PROJECT NO: DRAWN BY: DATE: SCALE: SHEET: KEY PLAN: COGDELL & MENDRALA ARCHITECTS, PC STRUCTURAL ENGINEER: MECHANICAL & PLUMBING ENGINEER: DULOHERY WEEKS, INC. 333 COMMERICAL DRIVE SAVANNAH, GA. 31406 SAUSSY ENGINEERING 400 E. JOHNNY MERCER BOULEVARD SAVANNAH, GA 31410 CIVIL ENGINEERS: COASTLINE CONSULTING SERVICES 138 CANAL STREET POOLER, GA 31322 FTE: 750 / 900 CORE 1500 Cogdell MendralaArchitects WOLVERTON & ASSOCIATES, INC. 7 CONGRESS STREET SAVANNAH, GA 31401 ELECTRICAL & COMMUNICATIONS ENGINEER: SUSTAINABLE DESIGN CONSULTANTS 415 BONAVENTURE DRIVE THUNDERBOLT, GA. 31404 1400 1600 1100 1300 1200 1000 FACILITY CODE: 625-0122 12" = 1'-0" 9/18/2015 9:23:31 AM C:\Users\gclark\Desktop\GREG'S JOBS\20141017 ELEC-GClark - 9-9-2015.rvt E0.01 ELECTRICAL LEGEND & LIGHT FIXTURE SCHEDULE GJC AUGUST 2015 1402 MAY HOWARD ELEMENTARY REPLACEMENT SCHOOL 115 WILMINGTON ISLAND ROAD SAVANNAH, GEORGIA 31410 LIGHT FIXTURE SCHEDULE TYPE DESCRIPTION LAMPS MANUFACTURER / SERIES FINISH MOUNTING NOTES A1 2'X4' TROFFER WITH 0.125" THICK #A12 ACRYLIC LENS 2-32 T8, 2950 LUMEN, 4100K METALUX "GR8" SERIES, LITHONIA, COLUMBIA, H.E. WILLIAMS WHITE GRID A1L 2'X4' TROFFER WITH 0.125" THICK #A12 ACRYLIC LENS LED: 4800 LUMEN, 4000K METALUX "GRLED" SERIES, LITHONIA, COLUMBIA, H.E. WILLIAMS WHITE GRID A2 2'X4' TROFFER WITH 0.125" THICK #A12 ACRYLIC LENS 3-32 T8, 2950 LUMEN, 4100K METALUX "GR8" SERIES, LITHONIA, COLUMBIA, H.E. WILLIAMS WHITE GRID A3 2'X4' TROFFER WITH 0.125" THICK #A12 ACRYLIC LENS 4-32 T8, 2950 LUMEN, 4100K METALUX "GR8" SERIES, LITHONIA, COLUMBIA, H.E. WILLIAMS WHITE GRID B2 VOLUMETRIC RECESSED 2'X4' TROFFER, LINEAR FACETED REFLECTOR, AND REGRESSED REFRACTIVE SYSTEM 2-32 T8, 2900 LUMEN, 4100K METALUX "ARCLINE" SERIES, LITHONIA, COLUMBIA, H.E. WILLIAMS WHITE GRID C FULL-BODY LED HIGHBAY WITH WIDE DISTRIBUTION AND 0.125" THICK ACRYLIC LENS AND WIREGUARD IN DOOR FRAME, INTEGRATED DIMMABLE DRIVER. LED: 24000 LUMEN, 4000K METALUX "HBLED" SERIES, LITHONIA, COLUMBIA, H.E. WILLIAMS WHITE CHAIN E STRIP FIXTURE, 4 FOOT LENGTH, WITH 14 GUAGE WIRE GUARD 2-32 T8, 2950 LUMEN, 4100K LITHONIA "C" SERIES, METALUX, COLUMBIA, HE WILLIAMS WHITE SURFACE/CHAIN F SEALED GASKETED 2'X4' TROFFER WITH ,ACRYLIC PRISMATIC LENS .125 THICK 3-32 WATT, T8, 4100 K FAILSAFE "CFDFA" SERIES, DAYBRITE, LITHONIA, METALUX, COLUMBIA WHITE GRID PROVIDE GASKET SETWEEN LENS AND DOOR FRAME G1 1'X4' FIXTURE, SURFACE MOUNT, LOW PROFILE, VANDLE RESISTANT. FIXTURE SHALL BE EQUIPPED WITH MOTION SENSOR. 2-32 T8, 2900 LUMEN, 4100K FAILSAFE "HVSL" SERIES, LUMINAIRE, LITHONIA, METALUX, HUBBELL WHITE SURFACE-CEILING G2 1'X4' FIXTURE, SURFACE MOUNT, LOW PROFILE, VANDLE RESISTANT. 2-32 T8, 2900 LUMEN, 4100K FAILSAFE "HVSL" SERIES, LUMINAIRE, LITHONIA, METALUX, HUBBELL WHITE SURFACE GW 1'X4' FIXTURE, SURFACE MOUNT, LOW PROFILE, VANDLE RESISTANT. FIXTURE SHALL BE EQUIPPED WITH MOTION SENSOR. 2-32 T8, 2900 LUMEN, 4100K FAILSAFE "HVSL" SERIES, LUMINAIRE, LITHONIA, METALUX, HUBBELL WHITE SURFACE-WALL K ELEVATOR PIT LIGHT, CLEAR GLASS GLOBE WITH DIE CAST ALUMINUM GUARD 1-42 WATT TTT, 4100K HUBBELL "NV2" SERIES, RIG-A-LITE, STONECO, EXCELINE, DAYBRITE, BASELITE EXPOSED PARTS CORROSION RESISTANT WALL - IN PIT L NARROW (4" MAX) EXTRUDED ALUMINUM SLOT FIXTURE, CONTINUOUS FROSTED ACRYLIC LENSE PROVIDE END PLATES AND CORNER COMPANIONS FOR COMPLETE SEAMLESS INSTALLATION FOR LENGTH INDICATED, INCLUDING CORNERS. LED: 1500 LUMENS, 4000K FOCAL POINT "SEEM 4", LEADALITE, MARK, NEORAY WHITE FLANGE - CONTINUOUS LP1 STAIRWELL LIGHT, RADIAL LOUVEROR ACRYLIC RIBBED LENS SHIELDING, DIE-CAST ALUMINUM END CAPS, VANDAL RESISTANT 1-F32T8 UP / 2-F32T8 DOWN NEORAY CIRQUE 6-DIP, LEDALITE, COLUMBIA, PAL HOUSING AND EXPOSED PARTS - WHITE AIRCRAFT CABLE PENDANT LENGTH: STAIRWELL 2'-0" LP2 NARROW (4" MAX) EXTRUDED ALUMINUM PENDANT FIXTURE, CONTINUOUS FROSTED ACRYLIC LENS, BI-DIRECTIONAL, DIMMABLE. SEE PLAN FOR LENGTH OF FIXTURE. LED: 580 LUMENS/FT DOWN, 400 LUMENS/FT UP, 4000K FOCAL POINT "SEEM 4", NULITE, PEERLESS, NEORAY FINISHES TO BE SELECTED BY ARCHITECT, MULTIPLE FINISHES AIRCRAFT CABLE PENDANT HEIGHT: BOTTOM OF FIXTURE AT 10'-0" A.F.F. CUSTOM LENGTH CORD AND CABLE REQUIRED LP3 1 1/2" LINEAR PENDANT, MATT WHITE ACRYLIC DIFFUSER. FIXTURES SHALL BE MOUNTED AT VARIOUS ANGLES (HORIZONTALLY AND VERTICALLY) TO BE DETERMINED BY THE ARCHITECT WITH MOUNTING HEIGHTS BETWEEN 18' AND 26'AFF. LED: 32 WATT, 4000K OCL "DASH" PENDANT, SPI, OR APPROVED EQUAL. MULTIPLE TO BE SELECTED BY ARCHITECT AIRCRAFT CABLE 277 VOLT M SLOT LED, TRIM FLANGE, CONTINUOUS FROSTED ACRYLIC LENS. PROVIDE END PLATES AND CORNER COMPANIONS FOR COMPLETE SEAMLESS INSTALLATION FOR LENGTH INDICATED, INCLUDING CORNERS. FIXTURE SHALL BE MOUNTED AT 12'-0", IN LINE WITH WINDOW MULLION, COORDINATE EXACT MOUNTING AND FLANGE REQUIREMENT WITH ARCHITECT PRIOR TO ROUGH IN. FIXTURE LENGTH AS INDICATED ON THE PLAN. 625 LUMENS PER FOOT, 4000K FOCAL POINT "SEEM 4 LED RECESSED", MARK, NULITE, NEORAY WHITE RECESSED OA ROUND, CANOPY CEILING MOUNTED LED LIGHT, RING STYLE, OPAL LENS LED: 1125 LUMEN, 20 WATT, 4000K McGRAW EDISON "TT" SERIES, FAILSAFE, LUMINAIRE, LITHONIA, HUBBELL, McGRAW EDISON TO BE SELECTED BY ARCHITECT SURFACE SEE ARCHITECTURAL CANOPY DETAILS FOR MOUNTING OB ROUND, WALL MOUNTED LED LIGHT, EYELID STYLE, OPAL LENS LED: 865 LUMEN, 40 WATT, 4000K FAILSAFE "TRE15 LED", LUMINAIRE, LITHONIA, HUBBELL, McGRAW EDISON TO BE SELECTED BY ARCHITECT SURFACE PROVIDE BATTERY WHERE INDICATED OC SEALED IN-GRADE FLOOD LIGHT, 7 INCH APERTURE SIZE, VERY WIDE FLOOD, UNIT SHALL BE SUITABLE FOR CONCRETE MOUNTING - PROVIDE CONCRETE BASE, INSTALL PER MANUFACTURERS RECOMENDATIONS, THERE SHALL BE NO CONDENSATION WITHIN UNIT, ADJUSTABLE IN GROUND. LED: 700 LUMEN, 14 WATT, 4100K LUMIERE "MONACO 3002A" SERIES, HYDREL, KIM, HUBBELL, LUMIERE BRUSHED STAINLESS IN GRADE P CYLINDRICAL 26" PENDANT, 5" DEPTH, SINGLE POINT QUADPOD SUSPENSION, 10% UPLIGHT, DIMMABLE LED: 4200 LUMENS, 59 WATT, 4000K IMPACT "WAF.R", BETA CALCO, SOLERA TO BE SELECTED BY ARCHITECT PENDANT PENDANT HEIGHT: 8'-0" A.F.F. P2 CYLINDRICAL 48" PENDANT, 5" DEPTH, SINGLE POINT QUADPOD SUSPENSION, 10% UPLIGHT, DIMMABLE LED: 10000 LUMENS, 141 WATT, 4000K IMPACT "WAF.R", BETA CALCO, SOLERA MULTIPLE TO BE SELECTED BY ARCHITECT PENDANT HEIGHT: FIXTURE B.E. AT 9'-0" A.F.F. S1 SURFACE MOUNT ADJUSTABLE DOWNLIGHT, DIE-CAST ALUMINUM BODY, 45 DEGREE TILT, 361 DEGREE ROTATION, INTEGRATED DIMMABLE DRIVER LED: 1300 LUMEN, 14 WATT, 4000K LUCIFER "CY1-AD-LED", BRUCK, OR APPROVED EQUAL BRUSHED ALUMINUM SURFACE - CEILING S2 WALL MOUNT, ROUND SCONCE, DIE-CAST ALUMINUM HOUSING 2-18 QE TERON "THORPE", DESIGNPLAN, FAIL-SAFE, LITHONIA TO BE SELECTED BY ARCHITECT SURFACE T1 7/8" METAL SNOOT, 12V, TRACK LIGHT HEAD WITH STRAIGHT TRACK. DIRECT FEED TRANSFORMER. TRACK SHALL BE MOUNTED VERTICALLY, SEE ARCHITECTURAL DETAILS 6 WATT DIMMABLE LED MR16 BRUCK "CLAREO SPOT" / VIA STRAIGHT TRACK, HALO, ARCHITRAK MATTE CHROME SURFACE PROVIDE CURVED TRACK WHERE INDICATED T2 TRACK LIGHT. SEE DETAIL 4/E0.02 W STAIRWELL LIGHT, RADIAL LOUVEROR ACRYLIC RIBBED LENS SHIELDING, DIE-CAST ALUMINUM END CAPS, VANDAL RESISTANT 1-F32T8 UP / 2-F32T8 DOWN NEORAY CIRQUE 6-DIW, LEDALITE, COLUMBIA, PAL HOUSING AND EXPOSED PARTS - WHITE WALL XA SINGLE FACE EXIT LIGHT, DIE CAST ALUMINUM, UNIVERSAL MOUNTING, GREEN LETTERS - DIRECTION OF ARROWS AS INDICATED. LED LITHONIA "LE" SERIES, BEGHELLI "LC1E" SERIES, DUAL LITE "CVD" SERIES, SURE-LITE "CX" SERIES BRUSHED STAINLESS UNIVERSAL 90 MINUTE BATTERY XB DOUBLE FACE EXIT LIGHT, DIE CAST ALUMINUM, UNIVERSAL MOUNTING, GREEN LETTERS - DIRECTION OF ARROWS AS INDICATED. LED LITHONIA "LE" SERIES, BEGHELLI "LC1E" SERIES, DUAL LITE "CVD" SERIES, SURE-LITE "CX" SERIES BRUSHED STAINLESS UNIVERSAL 90 MINUTE BATTERY XC SINGLE FACE EXIT LIGHT, EDGE LIT, UNIVERSAL MOUNTING, GREEN LETTERS - DIRECTION OF ARROWS AS INDICATED. LED LITHONIA "EDGR" SERIES, BEGHELLI "OL2" SERIES, HUBBELL "LE" SERIES, SURE-LITE "EUX" SERIES CLEAR UNIVERSAL CONCEALED BATTERY XD DOUBLE FACE EXIT LIGHT, EDGE LIT, UNIVERSAL MOUNTING, GREEN LETTERS - DIRECTION OF ARROWS AS INDICATED. LED LITHONIA "EDGR" SERIES, BEGHELLI "OL2" SERIES, HUBBELL "LE" SERIES, SURE-LITE "EUX" SERIES CLEAR UNIVERSAL CONCEALED BATTERY XEM 2 HEAD, WALL MOUNT EMERGENCY BATTERY WITH FIXTURE LITHONIA "ELM" SERIES, BEGHELLI, HUBBELL, SURE-LITE CHLORIDE, SURELITE, DUALITE BLACK SURFACE 90 MINUTE BATTERY 1 GENERAL: REFER TO LIGHTING PLANS FOR BALLAST VOLTAGES AND CONFIGURATION OF FIXTURES. FIXTURES CONTROLLED BY MULTIPLE SWITCHES SHALL HAVE CORRESPONDING QUANTITY OF BALLASTS. 2 FIXTURES SHALL BE MOUNTED SUSPENDED OR SURFACE, GIVING RIGHT OF WAY TO HVAC DUCT WORK AND/OR EQUIPMENT. 3 PROVIDE BACKBOX ON ALL FIXTURES OF THIS TYPE SO THAT FIXTURES WITH AND WITHOUT EMERGENCY BALLAST ARE AT THE SAME DEPTH. 4 GENERAL: COORINATE ALL MOUNTING OF FIXTURES (GRID/FLANGE) WITH ARCHITECTURAL RCP. 5 FIXTURES SHALL BE SELECTED FROM THE FIXTURE SCHEDULE NOT ONLY BY CATALOG NUMBER BUT WITH CONSIDERATION TO MOUNTING, NUMBER AND TYPE OF LAMPS, AND REFERENCED NOTES. THE FIRST FIXTURE INDICATED FOR EACH TYPE WITH CATALOG NUMBER IS THE BASIS OF DESIGN FIXTURE, OTHER LISTED MANUFACTURES PRODUCE EQUAL FIXTURE TO THE BASIS OF DESIGN FIXTURE. . LIGHT FIXTURE SCHEDULE NOTES: REVISION SCHEDULE DATE DESCRIPTION 9-04-2015 Addendum No. 1 9-09-2015 Addendum No. 2 9-18-2015 Addendum No. 6
Transcript
FACP
FSCU
VS
WF
FAA
DH
2E4.2
F FIRE ALARM PULL STATION. WALL MOUNTED 3 FT.-6 IN.ABOVE FLOOR.
FIRE ALARM SIGNAL, SPEAKER AND FLASHING LIGHT, 6'-8" AFF.
FIRE ALARM STROBE LIGHT, 6'-8" IN. MOUNTING HEIGHT.
FIRE ALARM CONNECTION, HOOD EXTINGUISHING SYSTEM, SEEMECHANICAL DRAWINGS FOR LOCATION. INTERLOCK WITH SHUNTTRIP BREAKERS FOR EQUIPMENT UNDER HOOD.
FIRE ALARM REMOTE LCD ANNUNCIATOR PANEL. FLUSH RECESSEDWALL MOUNTED.
FIRE ALARM DOOR HOLDER, WALL MOUNTED, CONSULT ARCHITECTURALDRAWINGS TO DETERMINE TYPE REQUIRED. PROVIDE POWER FROMNEAREST RECEPTACLE CIRCUIT AND CONNECT TO FIRE ALARM SYSTEM.
TAMPER SWITCH, FURNISHED AND INSTALLED WITH SPRINKLERSYSTEM. INTERLOCK WITH FIRE ALARM SYSTEM BY ELECTRICAL.
FLOW SWITCH, FURNISHED AND INSTALLED WITH SPRINKLERSYSTEM. INTERLOCK WITH FIRE ALARM SYSTEM BY ELECTRICAL.
FIRE ALARM SMOKE DETECTOR, CEILING MOUNTED.
FIRE ALARM DUCT SMOKE DETECTOR LOCATED IN HVAC DUCT.
FIRE ALARM CONTROL PANEL, SURFACE WALL MOUNTED.
FIRE ALARM SIGNAL, HORN. 6 FT.-8 IN. MOUNTING HEIGHT.
FIRE ALARM HEAT DETECTOR, 135 DEG, OPERATION.
P
WEATHER PROOF.
FIRE ALARM STROBE LIGHT, CEILING MOUNTED.
S
M
FIRE ALARM:
H
S WP
IC
AD
AC
S
2.
COORDINATE MOUNTING HEIGHTS, DEVICE LOCATIONS & POWER/CONTROLREQUIREMENTS WITH ARCHITECTURAL DRAWINGS AND SYSTEM INSTALLER.
INTRUSION DETECTION SYSTEM:
CONDUIT SLEEVE: NUMBER & SIZE, (2)-2" FOR ALLCLASSROOMS, (1)-2" FOR ALL OFFICES, UNO
ADMINISTRATIVE DISPLAY PHONE: WALL MOUNT AT 48" AFF
INTRUSION SYSTEM: KEY-PAD, MOUNT 48"AFF
SECURITY ACCESS: MOUNT ABOVE CEILING AT ENTRY WAY
INTRUSION DETECTION DEVICE: WALL MTD.
ACCESS CONTROL SYSTEMS
SEE DETAIL 1/T0.01 FOR POWER, POWER DISCONNECT, LOW VOLTAGE CABLING,BOXES AND CONDUIT REQUIREMENTS. REFER TO ARCHITECTURAL PLANSAND DOOR SPECIFICATIONS FOR ADDITIONAL REQUIREMENTS.
INTERCOM SPEAKER: 2' X 2' SQUARE CEILING MOUNTED
COORDINATE MOUNTING HEIGHTS, DEVICE LOCATIONS & POWER/CONTROLREQUIREMENTS WITH ARCHITECTURAL DRAWINGS AND SYSTEM INSTALLER.
SPEAKER SYSTEM:
CABLING COMPONENTS:
THE CONTRACTOR SHALL PROVIDE ROUGH-IN FOR ALL DEVICES ANDWIRING. ROUGH-IN REQUIREMENTS ARE SPECIFIED IN SECTION 261010. VERIFY ADJACENCY TO CORRESPONDING POWER RECEPTACLES. OTHERDEVICES WHOSE LOCATIONS ARE NOT DEPENDENT ON RECEPTACLEPLACEMENT SHALL BE COORDINATED WITH SYSTEM INSTALLER.
CEILING OR WALL MTD. TELECOMMUNICATION JUNCTION BOX ANDCONDUIT ROUGH-IN TO NEAREST ACCESSIBLE CEILING
ROUGH-IN FOR LOW VOLTAGE SYSTEMS:
SA
KP
J
J
OS
OS
OS
W
HD
C
PC
XX-1
T
M
ABBREVIATIONS:
LEGEND:
LIGHTING FIXTURES:
UPPERCASE LETTER ADJACENT TO FIXTURE DENOTES DESIGNATION PER THELIGHTING FIXTURE SCHEDULE. LOWERCASE LETTER DENOTES SWITCHLEG. THERESPECTIVE SWITCH WILL HAVE THE SAME DESTINATIONS. NUMERAL DENOTESBRANCH CIRCUIT CONNECTION.
REFER TO THE FIXTURE SCHEDULE FOR THE SPECIFIC FIXTURE INFORMATION.
EMERGENCY FIXTURES SHALL HAVE FACTORY INSTALLED INTERNAL BATTERIES,PER SPECIFICATIONS.
NL SUFFIX ADJACENT TO FIXTURE TYPE DENOTES NIGHT LIGHT. DO NOT SWITCHTHESE FIXTURES.
NON-EMERGENCY
EMERGENCY/BATTERY BACKUP
LIGHTING FIXTURE: LINEAR FLUORESCENT
ELECTRICAL EQUIPMENT:
REFER TO ONE-LINE DIAGRAM AND EQUIPMENT CONNECTION SCHEDULE FORLOAD DATA USED AS THE BASIS OF DESIGN AND REQUIRED CONNECTIONS.VERIFY LOAD AND LOCATION WITH EQUIPMENT CUT-SHEETS AND INSTALLER.
GENERAL NOTES:
DEVICE IDENTIFIER TAGS:
NUMERAL ADJACENT TO DEVICE DENOTES BRANCH CIRCUIT CONNECTION.IDENTIFIER TAGS ADJACENT TO DEVICES INDICATE:
WIRING DEVICES:
RECEPTACLES:
NOMINAL MOUNTING HEIGHT OF RECEPTACLES SHALL BE 18" TO CENTER, UNO. IFAPPLICABLE, ADJUST SO DEVICE COVER IS IN THE CENTER OF MASONRY COURSENEAREST THAT HEIGHT. THE HEIGHT ESTABLISHED SHALL GOVERN FOR ALL BOXINSTALLATIONS, WHERE INSTALLED IN MASONRY OR FRAMED WALLS.
SWITCHES:
MOUNTING HEIGHT OF SWITCHES SHALL BE 48" NOMINAL, ADJUSTED IN THE SAMEMANNER AS SPECIFIED ABOVE, FOR RECEPTACLES. LOWERCASE LETTER INDICATESSWITCHLEG CONNECTION. THE RESPECTIVE FIXTURE(S) WILL HAVE THE SAMEDESIGNATION.
BRANCH CIRCUITS:
CONDUCTOR COUNTS ARE SHOWN ON THE HOMERUNS ONLY. CONTRACTORSHALL DETERMINE COUNTS FOR INTERMEDIATE RUNS BASED ON THE MANNERIN WHICH THE CIRCUIT ELEMENTS ARE CONNECTED. REFER TO THESPECIFICATION SECTIONS 262010, 262080, & 26030 FOR SPECIALREQUIREMENTS.
LA-1,3,5
MISCELLANEOUS COMPONENTS:
3
4
a
K
O
LIGHTING FIXTURE: LINEAR FLUORESCENT
LIGHTING FIXTURE: LINEAR FLUORESCENT
LIGHTING FIXTURE: FLUORESCENT STRIP
LIGHTING FIXTURE: FLUORESCENT, WALL MTD.
DOWNLIGHT/SCONCE FIXTURE
EXIT: UNIVERSAL MTD.
DIRECTIONAL FIXTURES: EMERGENCY TYPE
LIGHT TRACK: LENGTH AS SHOWN
MOUNT ABOVE COUNTERTOP OR BACKSPLASH, 9" ABOVEWORK SURFACE TO CENTER
MOUNT DEVICE AT HEIGHT INDICATED
PROVIDE WEATHER-PROOF COVER
RECEPTACLE: SIMPLEX
RECEPTACLE: DUPLEX, TAMPER RESISTANT TYPE.
RECEPTACLE: GROUND-FAULT-INTERRUPTING, TAMPERRESISTANT TYPE
IN-SLAB FLOOR BOX: SEE SPECIFICATIONS
RECEPTACLE: DRYER, 30 AMP, 120/250 VOLT
RECEPTACLE: SPECIAL PURPOSE , COORDINATE NEMARATING WITH SPECIFIED EQUIPMENT
ELECTRIC WATER COOLER POWER CONNECTION, GFI OUTLET
HAND DRYER POWER CONNECTION: COORDINATE MOUNTINGHEIGHT W/ ARCHITECTURAL ELEVATIONSSEE HAND DRYER INSTALLATION DETAIL 1/E7.01.
RECEPTACLE FOR CLOCK (RECESSED) WITH CLOCKHANGER AND CLOCK. COORDINATE MOUNTING HEIGHT &LOCATION WITH ARCHITECTURAL FLOOR PLAN ANDELEVATIONS
RECEPTACLE: CEILING MOUNTED
SWITCH: SINGLE-POLE
SWITCH: THREE-WAY TYPE
SWITCH: FOUR-WAY TYPE
SWITCH: SUBSCRIPT THAT INDICATES CORRESPONDINGFIXTURES THAT SWITCH CONTROLS
SWITCH: KEY-OPERATED
SWITCH: OVERRIDE
OCCUPANCY SENSOR, CEILING MOUNTED
OCCUPANCY SENSOR, CORNER MOUNTED
OCCUPANCY SENSOR, WALL MOUNTED
SWITCH: MOTOR RATED, WITHOUT OVERLOAD PROTECTION
DISCONNECT SWITCH
DRY-TYPE TRANSFORMER
PANELBOARD: SURFACE MOUNTED
EQUIPMENT AS NOTED, SEE ABBREVIATIONS, THIS SHEET
PHOTOCELL: LOCATE UNDER EAVES, FACING NORTH, AVOIDANY OTHER OUTSIDE LIGHT SOURCE
BRANCH CIRCUIT: CONCEALED
BRANCH CIRCUIT: CONCEALED IN FLOOR SLAB
BRANCH CIRCUIT: EXPOSED
'HOMERUN' TO PANEL: NUMBER OF HASH MARKSINDICATES QUANTITY OF No. 12 AWG UNGROUNDEDCONDUCTORS IN 3/4" RACEWAY. GROUNDEDCONDUCTORS (NEUTRALS) ARE NOT SHOWN - ONEDEDICATED NEUTRAL IS REQUIRED FOR EACHUNGROUNDED CONDUCTOR INSTALLED, SEESPECIFICATIONS. EACH CONDUCTOR SHALL BE MIN. No.12 AWG UNLESS NOTED OTHERWISE.
JUNCTION BOX: MTD. ABOVE CEILING
JUNCTION BOX: WALL MTD. 7. WHERE COMPLETE BRANCH CIRCUIT WIRING IS NOT SHOWN, PROVIDE ACCORDINGTO HOMERUNS SHOWN AND CORRESPONDING CIRCUIT NUMBERS ADJACENT TO THEDEVICE OR FIXTURE. REFER TO THE SPECIFICATIONS FOR THE WIRING METHODS.BRANCH CIRCUIT RATINGS SHALL BE BASED ON OVERCURRENT DEVICE RATINGSSHOWN IN THE PANEL SCHEDULES.
8. REFER TO THE ELECTRICAL PANELBOARD SCHEDULES AND EQUIPMENT RATINGS &CONNECTIONS SCHEDULE FOR VOLTAGE, BRANCH CIRCUITS REQUIREMENTS,BREAKERS SIZES AND OTHER RELATED ELECTRICAL EQUIPMENT TO BE PROVIDEDAND/OR INSTALLED BY THE ELECTRICAL CONTRACTOR.
C
XX"
WP
A AMPERES
AFF ABOVE FINISHED FLOOR
AFG ABOVE FINISHED GRADE
AH AIR HANDLER
AIC AMPERAGE INTERRUPT CAPABILITY
ATU AIR TERMINAL UNIT
A/V AUDIO/VISUAL
AWG AMERICAN WIRE GAUGE
BFG BELOW FINISHED GRADE
B.E. BOTTOM EDGE
C. CONDUIT
CU CONDENSING UNIT
DAH DUCTLESS AIR HANDLER
DHP DUCTLESS HEAT PUMP
DIA. DIAMETER
VS
VS
VS
VACANCY SENSOR, CEILING MOUNTED
VACANCY SENSOR, CORNER MOUNTED
VACANCY SENSOR, WALL MOUNTED
THE ELECTRICAL DRAWINGS ARE ONLY PART OF THE CONTRACT DOCUMENTS.THE CONTRACTOR SHALL REVIEW ALL OF THE DRAWINGS AND SPECIFICATIONSFOR THEIR INTERRELATIONSHIP AND REQUIRED COORDINATION BETWEENDISCIPLINES.
SYMBOL WHERE SHOWN AT OR NEAR A ROOM INDICATES THATROOM IS SHOWN AS A TYPICAL LARGE SCALE. (2) INDICATESTHE DETAIL NUMBER AND (E4.2) INDICATES THE SHEET NUMBER.
ALL CONDUCTORS SHALL BE COPPER UNLESS NOTED WITH THE WORD "ALUMINUM"IN THE DESCRIPTION.
EACH DOOR SHALL HAVE ONE 3/4"C. FROM DOOR FRAME TO DOOR CONTROLLERENCLOSURE (ASSUME WITHIN 50' OF DOOR), ONE DEDICATED 20A, 120 VOLT CIRCUITTO SAME CONTROLLER ENCLOSURE.
PRIOR TO RUNNING ANY CONDUIT, COORDINATE LOCATIONS OF ALL WALL MOUNTEDDEVICES WITH WALL MOUNTED ACOUSTICAL PANELS. SEE ARCHITECTURAL DRAWINGSFOR SPACES IN WHICH WALL PANELS ARE INSTALLED.
PRIOR TO RUNNING CONDUIT, COORDINATE LOCATIONS OF ALL WALL MOUNTED DEVICESWITH WALL MOUNTED SAFETY PADS IN GYMNASIUM.
1.
3.
4.
5.
6.
E.C.B. ENCLOSED CIRCUIT BREAKER
EF EXHAUST FAN
EH ELECTRIC HEATER
EMCS ENERGY MANAGEMENT CONTROL UNIT
FAAP FIRE ALARM ANNUNCIATOR PANEL
FACP FIRE ALARM CONTROL PANEL
G GROUND
GFI GROUND-FAULT INTERRUPTING
HP HORSE POWER
HRVU HEAT RECOVERY VENTILATING UNIT
HWCP HOT WATER CIRCULATING PUMP
KCMIL KILO CIRCULAR MIL
MAH MAKEUP AIR HEATER
MB MAIN BREAKER
MCA MINIMUM CIRCUIT AMPS
MIN MINIMUM
MOCP MAXIMUM OVERCURRENT PROTECTION
MTD MOUNTED
No. NUMBER
NEC NATIONAL ELECTRIC CODE
NTS NOT TO SCALE
PIV POST INDICATOR VALVE
RGS RIGID GALVANIZED STEEL
RTU ROOFTOP UNIT
SF SUPPLY FAN
SPD SURGE PROTECTION DEVICE
SWBD SWITCHBOARD
TGB TELECOMMUNICATIONS GROUND BUS
TMGB TELECOMMUNICATIONS MAIN GROUND BUS
TTW THROUGH-THE-WALL HEAT PUMP
TYP TYPICAL
UH UNIT HEATER
UNO UNLESS NOTED OTHERWISE
V VOLTAGE
W WATTAGE
W/ WITH
WH WATER HEATER
WHP WALL-MOUNTED HEAT PUMP
WP WEATHER PROOF
XFMR TANSFORMER
SMOKE DAMPER, 120V, PROVIDE POWER CONNECTION AND ALLNEEDED SMOKE DETECTION AND CONTROL MODULES AS REQUIREDBY NFPA 72 FOR PROPER OPERATION.
SD
FIRE ALARM REMOTE VOICE EVACUATION MICROPHONE FLUSH RECESSEDWALL MOUNTED.
MIC
"C" DESIGNATION INDICATES CEILING MOUNTED.
S SPEAKER - SEE DRAWINGS AND SPECIFICATIONS FOR TYPE.
LA-1,3,5'HOMERUN' TO PANEL FOR EQUIPMENT: SEE EQUIPMENTCONNECTION SCHEDULES FOR SIZE OF FEEDER ANDNUMBER OF CONDUCTORS.
V SWITCH: LOW VOLTAGE OVERRIDE SWITCH FOR VACANCYSENSOR. WHERE MULTIPLE SUBSCRIPTS ARE INDICATED("ab" FOR EXAMPLE) PROVIDE A PUSHBUTTON FOR EACHCORRESPONDING GROUP OF FIXTURES TO BE CONTROLLED(2 BUTTON SWITCH FOR "ab" FOR EXAMPLE). THEPUSHBUTTONS SHALL BE MOUNTED UNDER A SINGLE GANGFACEPLATE.
DSWITCH: DIMMER TYPE. DIMMER SHALL BE COMPATIBLE WITHBALLAST INSTALLED. PROVIDE ALL LOW VOLTAGE CABLINGAND CONNECTIONS FOR 0 TO 10 VOLT DIMMING.
FIRE ALARM CARBON MONOXIDE DETECTOR.
OSHB
OCCUPANCY SENSOR, CEILING MOUNTED HIGHBAY TYPE
SCENE CONTROLLER
STARTER/DISCONNECT SWITCH. SEE PLAN FOR SIZE, SEESPECIFICATIONS FOR TYPE.
L NARROW (4" MAX) EXTRUDED ALUMINUM SLOTFIXTURE, CONTINUOUS FROSTED ACRYLIC LENSEPROVIDE END PLATES AND CORNER COMPANIONS FORCOMPLETE SEAMLESS INSTALLATION FOR LENGTHINDICATED, INCLUDING CORNERS.
LP2 NARROW (4" MAX) EXTRUDED ALUMINUM PENDANTFIXTURE, CONTINUOUS FROSTED ACRYLIC LENS,BI-DIRECTIONAL, DIMMABLE. SEE PLAN FOR LENGTH OFFIXTURE.
LED: 580LUMENS/FTDOWN, 400
LUMENS/FT UP,4000K
FOCAL POINT "SEEM4", NULITE, PEERLESS,NEORAY
FINISHES TOBE SELECTED
BYARCHITECT,MULTIPLEFINISHES
AIRCRAFT CABLE PENDANT HEIGHT: BOTTOMOF FIXTURE AT 10'-0" A.F.F.CUSTOM LENGTH CORD ANDCABLE REQUIRED
LP3 1 1/2" LINEAR PENDANT, MATT WHITE ACRYLICDIFFUSER. FIXTURES SHALL BE MOUNTED AT VARIOUSANGLES (HORIZONTALLY AND VERTICALLY) TO BEDETERMINED BY THE ARCHITECT WITH MOUNTINGHEIGHTS BETWEEN 18' AND 26'AFF.
LED: 32 WATT,4000K
OCL "DASH" PENDANT,SPI, OR APPROVEDEQUAL.
MULTIPLE TOBE SELECTED
BYARCHITECT
AIRCRAFT CABLE 277 VOLT
M SLOT LED, TRIM FLANGE, CONTINUOUS FROSTEDACRYLIC LENS. PROVIDE END PLATES AND CORNERCOMPANIONS FOR COMPLETE SEAMLESS INSTALLATIONFOR LENGTH INDICATED, INCLUDING CORNERS.FIXTURE SHALL BE MOUNTED AT 12'-0", IN LINE WITHWINDOW MULLION, COORDINATE EXACT MOUNTING ANDFLANGE REQUIREMENT WITH ARCHITECT PRIOR TOROUGH IN. FIXTURE LENGTH AS INDICATED ON THEPLAN.
625 LUMENSPER FOOT,
4000K
FOCAL POINT "SEEM 4LED RECESSED",MARK, NULITE,NEORAY
WHITE RECESSED
OA ROUND, CANOPY CEILING MOUNTED LED LIGHT, RINGSTYLE, OPAL LENS
OC SEALED IN-GRADE FLOOD LIGHT, 7 INCH APERTURESIZE, VERY WIDE FLOOD, UNIT SHALL BE SUITABLE FORCONCRETE MOUNTING - PROVIDE CONCRETE BASE,INSTALL PER MANUFACTURERS RECOMENDATIONS,THERE SHALL BE NO CONDENSATION WITHIN UNIT,ADJUSTABLE IN GROUND.
2-18 QE TERON "THORPE",DESIGNPLAN,FAIL-SAFE, LITHONIA
TO BESELECTED BY
ARCHITECT
SURFACE
T1 7/8" METAL SNOOT, 12V, TRACK LIGHT HEAD WITHSTRAIGHT TRACK. DIRECT FEED TRANSFORMER.TRACK SHALL BE MOUNTED VERTICALLY, SEEARCHITECTURAL DETAILS
6 WATTDIMMABLE LED
MR16
BRUCK "CLAREOSPOT" / VIA STRAIGHTTRACK, HALO,ARCHITRAK
MATTECHROME
SURFACE PROVIDE CURVED TRACKWHERE INDICATED
T2 TRACK LIGHT. SEE DETAIL 4/E0.02
W STAIRWELL LIGHT, RADIAL LOUVEROR ACRYLIC RIBBEDLENS SHIELDING, DIE-CAST ALUMINUM END CAPS,VANDAL RESISTANT
1-F32T8 UP /2-F32T8 DOWN
NEORAY CIRQUE6-DIW, LEDALITE,COLUMBIA, PAL
HOUSINGAND
EXPOSEDPARTS -WHITE
WALL
XA SINGLE FACE EXIT LIGHT, DIE CAST ALUMINUM,UNIVERSAL MOUNTING, GREEN LETTERS - DIRECTIONOF ARROWS AS INDICATED.
LED LITHONIA "LE" SERIES,BEGHELLI "LC1E"SERIES, DUAL LITE"CVD" SERIES,SURE-LITE "CX"SERIES
BRUSHEDSTAINLESS
UNIVERSAL 90 MINUTE BATTERY
XB DOUBLE FACE EXIT LIGHT, DIE CAST ALUMINUM,UNIVERSAL MOUNTING, GREEN LETTERS - DIRECTIONOF ARROWS AS INDICATED.
LED LITHONIA "LE" SERIES,BEGHELLI "LC1E"SERIES, DUAL LITE"CVD" SERIES,SURE-LITE "CX"SERIES
BRUSHEDSTAINLESS
UNIVERSAL 90 MINUTE BATTERY
XC SINGLE FACE EXIT LIGHT, EDGE LIT, UNIVERSALMOUNTING, GREEN LETTERS - DIRECTION OF ARROWSAS INDICATED.
LED LITHONIA "EDGR"SERIES, BEGHELLI"OL2" SERIES,HUBBELL "LE" SERIES,SURE-LITE "EUX"SERIES
CLEAR UNIVERSAL CONCEALED BATTERY
XD DOUBLE FACE EXIT LIGHT, EDGE LIT, UNIVERSALMOUNTING, GREEN LETTERS - DIRECTION OF ARROWSAS INDICATED.
LED LITHONIA "EDGR"SERIES, BEGHELLI"OL2" SERIES,HUBBELL "LE" SERIES,SURE-LITE "EUX"SERIES
CLEAR UNIVERSAL CONCEALED BATTERY
XEM 2 HEAD, WALL MOUNT EMERGENCYBATTERY
WITH FIXTURE LITHONIA "ELM"SERIES, BEGHELLI,HUBBELL, SURE-LITECHLORIDE, SURELITE,DUALITE
BLACK SURFACE 90 MINUTE BATTERY
1 GENERAL: REFER TO LIGHTING PLANS FOR BALLAST VOLTAGES AND CONFIGURATION OF FIXTURES. FIXTURES CONTROLLED BYMULTIPLE SWITCHES SHALL HAVE CORRESPONDING QUANTITY OF BALLASTS.
2 FIXTURES SHALL BE MOUNTED SUSPENDED OR SURFACE, GIVING RIGHT OF WAY TO HVAC DUCT WORK AND/OR EQUIPMENT.
3 PROVIDE BACKBOX ON ALL FIXTURES OF THIS TYPE SO THAT FIXTURES WITH AND WITHOUT EMERGENCY BALLAST ARE AT THE SAMEDEPTH.
4 GENERAL: COORINATE ALL MOUNTING OF FIXTURES (GRID/FLANGE) WITH ARCHITECTURAL RCP.
5 FIXTURES SHALL BE SELECTED FROM THE FIXTURE SCHEDULE NOT ONLY BY CATALOG NUMBER BUT WITH CONSIDERATION TOMOUNTING, NUMBER AND TYPE OF LAMPS, AND REFERENCED NOTES. THE FIRST FIXTURE INDICATED FOR EACH TYPE WITH CATALOGNUMBER IS THE BASIS OF DESIGN FIXTURE, OTHER LISTED MANUFACTURES PRODUCE EQUAL FIXTURE TO THE BASIS OF DESIGNFIXTURE. .
LIGHT FIXTURE SCHEDULE NOTES: REVISION SCHEDULE
DATE DESCRIPTION
9-04-2015 Addendum No. 1
9-09-2015 Addendum No. 2
9-18-2015 Addendum No. 6
HD HD
HD HD
WW
WP
WP
WP
C
C
AV
WP
J
J
C
J
C
C C
C
C
WP
WP
CC
C
WP WP
WP WP
J J J
J J J
C
C
C
CHASE
1022.1
JAN
1022
MEN
1021
WOMEN
1023
CORRIDOR
1004
CORRIDOR
1001.1
CORRIDOR
1001.2
VESTIBULE
1000
RECORDS
1011
STORAGE
1020
MAILROOM
1005
CORRIDOR
1001
CLOS
1012.2
LEAD TEACHER
1016ASSIST. PRINCIPAL
1018
TESTING
1014
CLOSET
1014.1
JAN
1015
TLT
1017
SITTING AREA
1004.1SUPPLY
1007
CLINIC
1019
COTS
1019.1
CORR
1004.2
CLOSET
1004.4
CORR
1004.3
TLT
1012.1
CONFERENCE
1010
PRINCIPAL
1012
TLT
1019.2TLT
1013
WORKROOM
1006
OFFICE
1009
DATA CLERK
1008
CLERICAL
1003
RECEPTION
1002
THIS AREA SERVED BYPANEL: L1A
THIS AREA SERVED BYPANEL: L1B
/1 E2.13
/1 E2.13
/1
E2.1
1/
1E
2.1
1
/1 E2.12
C
C
C
C
C
NOTE 3
CC
C
C
C C
NOTE 1
C C
C
C
C
C
NOTE 4
C
CNOTE 2
NOTE 6
NOTE 7
NOTE 2
NOTE 9
NOTE 8
NOTE 10
NOTE 11
NOTE 11
NOTE 12
6060
60
60
58 58 2 4
5858
58
56
56 56
6 8
56
L1B- 5658 60
60
56
L1B- 24
L1B- 68
7 7
5
5
9
9
5
3
3
3
3
1
1
1
35
1
35
5
57
9
53
53
55
57
53
53
51
51
51
51 51 49
49
49
49
49
4545
45
45
43
43
43
43
41
41 41
39
41
3939
47
1947
47
47
47
21 21 21
21
19
35
191919
21
2123 25,27 33
31
23
23
29
17
17
17
17
39 3737
3739
35
35
13
13
13151515
15 15
9
11
11
11
3
L1A- 25,27
L1A- 13 5
911
L1A- 1315 17
L1A- 19
21 23L1A- 29
3331
L1A- 3537 39
41
L1A- 4143 45
L1A- 4749 51
L1A- 5355 57
60" AFF
60" AFF
60" AFF
59
45
L1A- 7
NOTE 2
EQUIPMENT
1103
LEARNING CENTER
1111
LEARNING CENTER
1112
WORKROOM
1104
BROADCAST
1109
OFFICE
1105
CIRCULATION
1101.1
STORAGE
1106
TLT
1104.1
TLT
1107
TLT
1108
STAFF
1110
COMPUTER LAB
1102
MEDIA CENTER-2
1101-2
THIS AREA SERVED BYPANEL: L1B
/1 E2.13
/1 E2.13
/2
E2.1
1
/1
E2.1
4
/1 E2.12
/2 E2.11
/1 E2.12
4E5.02
1E5.03
NOTE 3
NOTE 3
C C C
C C
NOTE 2
NOTE 2
NOTE 5
NOTE 2
C
C C C
C
NOTE 13
1
1
13
13
3
3
5
5
7
7
L1B- 13
L1B- 57
23
23
23
15 15
17
17
17
17
17
17
17
15
21
21
55
1111
13
11
25
25
25
25
57
19
19
1927
31 31 31
29
29
29
29
29
27
27 27
39
33
33
35 35
37
39
37
41
41 41
41
53
53
53
23
55
55
55
55
11
9 9
11
47
47
47 4749
49
49
45
45
45 43 43 43
43
48" AFF FOR WALLMOUNTED PHONE
47
43
23
L1B- 913
L1B- 1517 19
L1B- 2123 25
L1B- 2729 31
L1B- 3335 37
L1B- 39
51 51
51
5151
L1B- 4143 45
L1B- 4749 51
L1B- 5355
L1B- 616563
L1B- 737775
L1B- 798381 87 89
L1B- 859593
7169L1B- 67
L1B- 91
NOTE 4
49
45
57
5959
L1B- 5759
NOTE 2
FINISHED CEILING3#12,1/2IN. FLEX
3#12, 1 / 2 IN. C
INTERIOR VIEW
1 IN. C.
1 IN. C.
MAKE ALL CONNECTIONS AND PROVIDE ALL ITEMS REQUIRED FORCOMPLETE OPERATING SYSTEM AS REQUIRED BY MANUFACTURER
ELECTRICDOORSTRIKE
INTERIOR VIEW
ELECTRICDOORSTRIKE
PUSH TOEXITBUTTONS
REQUESTTO EXITDETECTOR
REQUESTTO EXITDETECTOR
DOORS WITH ELECTRIC DOOR STRIKE
POWER SUPPLYAND CONTROLLER
(TYPICAL)
LOCATE AT RECEPTIONDESK COORDINATEEXACT LOCATION WITHARCHITECT
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
NOT TO SCALE8/7
/2015 3
:27:4
3 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
7-2
0-2
015.r
vt
E2.11
FIRST FLOORPOWER PLAN -BUILDING 1000& 1100
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
1/8" = 1'-0"E2.11
POWER PLAN - 10002 1/8" = 1'-0"E2.11
POWER PLAN - 11001
(THIS SHEET ONLY)NOTES:8 PROVIDE DOOR INTERCOM SYSTEM AIPHONE JK-1MED MASTER
STATION WITH WIDE ANGLE VIEW, PAN/TILT/ZOOM CONTROL,COLOR MONITOR AND BUILT IN PICTURE MEMORY-PROVIDE WITHMCW-S/A DESK STAND. MASTER STATION SHALL PROVIDE DOORRELEASE, INTERFACE WITH DOOR LOCKING SYSTEM.
9 PROVIDE WEATHER PROOF DOOR SUBSTATION JK-DVF (FLUSHMOUNT) OR JK-DV (SURFACE MOUNT) OUTSIDE OF ENTRY.
10 MAKE CONNECTION TO NEAREST RECEPTACLE CIRCUIT FORPOWER, PROVIDE ALL TRANSFORMERS RACEWAY AND CABLINGREQUIRED FOR COMPLETE OPERATIONAL SYSTEM.
11 MAKE FINAL CONNECTION TO DOOR LOCK ACCORDING TO THEMANUFACTURERS INSTRUCTIONS.THE DOOR IS TO UNLOCKWHEN PUSH BUTTON IS PRESSED SEE DOOR LOCK CONNECTIONDETAIL.
12 PUSH TO EXIT BUTTONS, SEE DOOR LOCK CONNECTIONSDETAIL, THIS SHEET.
13 COORDINATE OUTLET LOCATION ON COLUMN AND CONDUITROUTING WITH ARCHITECTPRIOR TO ROUGH IN.
1 MOUNT IN CABINET FOR MICROWAVE, COORDINATE EXACTOUTLET MOUNTING HEIGHT PRIOR TO ROUGH IN. PROVIDERECESSED SIMPLEX OUTLET.
2 PROVIDE RECESS OUTLET BOXES MOUNTED AT 60" A.F.F. FORCABLING AND POWER FOR WALL MOUNT TELEVISION.
3 MOUNT OUTLETS IN KNEE SPACE OF CABINET, CONCEAL ALLCONDUIT. ROUTE DATA CONDUITS UNDER GROUND TONEAREST WALL, THEN TURN OUT ABOVE ACCESSIBLE CEILING.
4 PROVIDE RECEPTACLE AND DATA OUTLET AT 52" A.F.F. FORKRONOS TIMECLOCK. COORDINATE EXACT MOUNTING LOCATIONWITH ARCHITECT PRIOR TO ROUGH IN.
5 WHERE OUTLET IS LOCATED AT BOOK STACK, OUTLET SHALL BEINSTALLED IN BASE OF BOOK STACK, MOUNTED HORIZONTALLY.COORDINATE STACK LOCATIONS WITH ARCHITECT.
6 PROVIDE OUTLET FOR COUNTERTOP ICE DISPENSER.
7 PROVIDE 4#10, 3/4"C HOMERUN
NOT TO SCALEE2.11
DOOR LOCK CONNECTIONS3
A COORDINATE LOCATIONS OF OUTLETS WITH ARCHITECT, SEEDETAIL. 2/E7.01.
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
1/8" = 1'-0"8/7
/2015 3
:27:4
7 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
7-2
0-2
015.r
vt
E2.12
FIRST FLOORPOWER PLAN -BUILDING 1200
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
1/8" = 1'-0"E2.12
POWER PLAN - 12001
1 MOUNT BOX FOR AUDIO VISUAL CONNECTIONS AT 48" AFF.SEE DETAIL FOR BOX SIZE, CONFIGURATION AND CONDUITREQUIREMENTS.
2 SINGLE GANG JUNCTION BOX WITH 1" C TURNED OUTABOVE CEILING FOR PROJECTOR CONTROLLER.
3 POWER FOR PROJECTOR AT 96", COORDINATE LOCATIONWITH ARCHITECT PRIOR TO ROUGH IN.
4 PROVIDE 3 POSITION, CENTER OFF SWITCH COMPATIBLEWITH PROJECTOR SCREEN MOTOR / MOTORIZED DIVIDERCURTAIN. MAKE ALL CONNECTIONS REQUIRED FORCOMPLETE OPERABLE SYSTEM.
5 MOTORIZED DIVIDER CURTAIN HUNG FROM STRUCTURE.COORDINATE EXACT LOCATION PRIOR TO ROUGH IN.PROVIDE 3#10, 1/2"C HOMERUN.
6 PROJECTOR SCREEN MOTOR. COORDINATE EXACTLOCATION WITH OWNER. PROVIDE 3#10, 1/2"C. HOMERUN.
(THIS SHEET ONLY)NOTES:
(THIS SHEET ONLY)GENERAL NOTES:A COORDINATE LOCATIONS OF OUTLETS WITH ARCHITECT, SEE
DETAIL. 2/E7.01.
REVISION SCHEDULE
DATE DESCRIPTION
x1
x1
x1
x1x1
DN
WP
W W W
WP
WP
WP
WP
WP
C
WP
WP
CAFETERIA
1304
ELEC
1301
CORR
1300
JAN
1306
TRASH VEST
1305
OFFICE
1314
CHEM STOR
1313
SERVERY
1307
ELECTRICAL
1318
TLT
1317
DISH WASH
1308
COOLER/FREEZER
1312
RECEIVING
1315
KITCHEN
1311
DRY STORAGE
1310
TABLE/CHAIR STORAGE
1309
LOCKER
1316
SCRUBBER STORAGE
1302
MDF
1303SUPPLIES
1304.1
MECHANICAL-1
1319-1
MECHANICAL-2
1319-2
CORRIDOR-2
1100-2
MSB
H1K L1KL1KT-1K
H1M
MSB
T-1B
L1B
L1B
L1B
H1B
THIS AREA SERVED BYPANEL: L1B
THIS AREA SERVED BYPANEL: L1K
THIS AREA SERVED BYPANEL: L1B
THIS AREA SERVED BYPANEL: L1K
1E5.01
/2 E2.11
/1
E2.1
4
/1 E2.11 /2
E2.1
1
/1
E2.1
1
4E5.03
T-EM
L1K-EM
ECB L1K-EM
NLKELKWP
97
97 97 97 97 97
101
99 101 101
101
101
107105103109
109113
115
111
111
109
109
L1B- 97
107105L1B- 103
L1B- 109111
3
3
3
3
3
5
5
5
5
5
7
7
7
3
L1K- 37
5
10199
OUTLET SHALL BELOCATED AT IRRIGATIONCONTROL PANEL. VERIFYEXACT LOCATION PRIORTO ROUGH IN.
MTS
MAKE FINAL CONNECTION TO UNITACCORDING TO MANUFACTURERSINSTRUCTIONS.
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
1/8" = 1'-0"8/7
/2015 3
:28:0
8 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
7-2
0-2
015.r
vt
E2.22
SECOND FLOORPOWER PLAN -BUILDING 2500& 2600
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
1/8" = 1'-0"E2.22
POWER PLAN - 25001 1/8" = 1'-0"E2.22
POWER PLAN - 26002
A COORDINATE LOCATIONS OF OUTLETS WITH ARCHITECT, SEEDETAIL. 2/E7.01.
(THIS SHEET ONLY)GENERAL NOTES:
REVISION SCHEDULE
DATE DESCRIPTION
x1
x1
x1
x1
W/D
X 6' - 0"21' - 4"
X 11' - 4"13' - 4"
X 22' - 8"15' - 4"
X 21' - 4"18' - 8"
X 28' - 8"38' - 0"
X 26' - 8"46' - 8"
X 24' - 8"19' - 6"
X 8' - 8"6' - 0"
X 8' - 8"12' - 0"
X 9' - 4"7' - 4"X 8' - 8"10' - 8"
X 7' - 4"8' - 0"
FE-K FEB
FEC
FEC
40°
40°
40°
40°
D
D
D
D
DD
2148
2148
RR D
R RD
21362136
2136
2136
2136
2148
21482148
2148 2148
2148
21482148
2148 2148
D
D
CH
EM
D2
FS
D1
2148
2148
2148
2148
2148
2148
2148
2148 2148
2148
2148
2148
2148
D
D
W/DE1
E15
E14b
E17
E23E23
E25
E26
E62
E26
E24
E31
E61
E27 E28
E62
E61
E19
E51
E22
E22
E21
E46E45
E14
E44
E44b
E46E45
E25
COOLER
FREEZER
EW2
E54
E55
E59
E49
E33
WP
WP
JJ
SS
J
JJ
J
JJ
J
C
CHEM STOR
1313
OFFICE
1314
RECEIVING
1315
LOCKER
1316
TLT
1317
KITCHEN
1311
SERVERY
1307
TRASH VEST
1305
TABLE/CHAIR STORAGE
1309
JAN
1306
DISH WASH
1308
DRY STORAGE
1310
COOLER/FREEZER
1312
L1K- 1
NOTE 1
NOTE 2
NOTE 4
NOTE 3
6
4
2
L1K- 24 6
L1K- 12,14
H1K- 2,4,6
8
10
L1K- 810
H1K- 8,10,12
L1K- 16L1K- 18
L1K- 20
L1K- 2420
24
26 22
26
22
@24"
@24"
@48" @48"
@48"
@48"
@48"@48"
@48"
@48"
@48"
@48"
28
28
NOTE 25
@48" @48"30 32
L1K- 3032
36
34
38
38
38
38
38
L1K- 3438
36
MSB- 13
NOTE 15
NOTE 15
NOTE 15
NOTE 15
NOTE 5
NOTE 6
NOTE 7
NOTE 10
NOTE 10
NOTE 10
NOTE 10
NOTE 9
EW5
EW2
EW7
7#12, 1"C
7#12, 1"C
TO CONDENSINGSYSTEM CONTROLPANEL EW6
EW4
NOTE 10
L1K-EM- 6
L1K-EM- 6
NOTE 9
EW1
L1K-EM- 4
L1K-EM- 1,3,5
NOTE 8
NOTE 8
NOTE 11 NOTE 12 NOTE 11 NOTE 12
NOTE 13
NOTE 14NOTE 16
NOTE 15
NOTE 15
NOTE 15
NOTE 17
L1K- 35,37,39
NOTE 18
NOTE 18L1K- 46,48 L1K- 52,54
L1K-EM- 2
L1K-EM- 7
7 9
9
L1K- 58,60 L1K- 62,64L1K- 66
68
68
66
NOTE 20
H1K- 26,28,30
H1K- 20,22,24
NOTE 2
H1K- 14,16,18
NOTE 19
NOTE 21
NOTE 22
NOTE 23
NOTE 2
NOTE 24
H1K- 32,34,36
70
7070
70 70
70
70
70
L1K- 70
76
76
76
76
72
72
72
74
74
74
74
L1K- 727674
NOTE 15
NOTE 15
NOTE 15
NOTE 15
NOTE 15
NOTE 15
NOTE 15
NOTE 15
NOTE 13
NOTE 13
NOTE 14
NOTE 14
@48" 78
L1K- 78
NOTE 26
L1K- 80,82
4#10
L1K- 84
38
H1K T-1K L1K L1K
6 6
DESIGN IS BASED ON SINGLE CIRCUIT FEED TO FREEZER AND DUAL CIRCUITFEED TO COOLER. VERIFY CONNECTIONS FOR UNITS ACTUALLY PROVIDED ANDMODIFY ACCORDINGLY.
ALL CONDUITS ENTERING REFRIGERATED SPACES SHALL BE RGS. PROVIDESEALING FITTING AT ALL ENTRY POINTS AND SEAL TO PREVENT THEENTRANCE OF MOISTURE.
PROVIDE ROUGH-IN FOR CONTROL WIRING AS REQUIRED BY EQUIPMENTINSTALLATION DRAWINGS.
PANELSERVINGFREEZER/COOLER.
LOCATE WITHIN SIGHT OFINDOOR COIL. COORDINATESWITCH LOCATION WITHEQUIPMENT INSTALLER,TYP.
FREEZER
COILCONDENSERCONTROLPANEL
CONDENSERCONTROLPANEL
COIL
COOLER
(FREEZER COOLER CONNECTIONS DETAIL )NOTES:S
SWP
S
SWP
120V CIRCUIT
KITCHEN HOOD FIRE SUPPRESSIONNORMALLY OPEN CONTACTS IN
SYSTEM THAT CLOSE UPONACTIVATION
120V CIRCUIT
KITCHEN HOOD FIRE SUPPRESSIONNORMALLY OPEN CONTACTS IN
14 CONNECT CORD AND PLUG SET OR PREWIRED FLEXIBLE CONDUIT PROVIDED WITH UDS TO EQUIPMENT TERMINALS
FOR EACH PIECE OF KITCHEN EQUIPMENT. COORDINATEWITH UDS BEING INSTALLED.
15 CONNECT UDS ELECTRICAL FIELD JOINTS BY BOLTING BUS BARS AND/OR WIRING TOGETHER. CONNECT ALL
CONTROL WIRING FIELD JOINT MOLDED CONNECTORS.
16 INSTALL 120 VOLT CIRCUIT FROM FIRE EXTINGUISHINGSYSTEM TO FUEL SHUT-OFF TERMINAL BLOCK IN UDS.COORDINATE EXACT CONNECTION POINTS WITH UDSBEING INSTALLED.
17 PROVIDE 2-WIRE CIRCUIT FROM UDS RISER TO REMOTE GAS SOLENOID VALVE. COORDINATE EXACT CONNECTION
POINTS AND WIRE SIZE WITH UDS BEING INSTALLED.
18 PROVIDE 1 IN. C. EMPTY WITH PULLSTRING FOR POINT OFSALE CABLING.
19 PROVIDE FLUSH 30A/3P ECB WITH STAINLESS STEELCOVER AND DOUBLE GASKET.
20 PROVIDE FLUSH 40A/3P ECB WITH STAINLESS STEELCOVER AND DOUBLE GASKET.
21 PROVIDE SERVICE OUT OF WALL AT 16" A.F.F. CONNECTTO TERMINALS AT 12" A.F.F.
22 PROVIDE SERVICE OUT OF WALL AT 8" A.F.F. CONNECT TOTERMINALS ON BOOSTER HEATER AT 4" A.F.F..
23 PROVIDE SERVICE OUT OF WALL AT 64" A.F.F. CONNECTTO TERMINALS ON DISSHWASHER AT 64" A.F.F..
24 PROVIDE SERVICE OUT OF WALL AT 16" A.F.F., EXTEND TOCONTROL PANEL AND SOLENOID VALVE AND CONNECT TOTERMINALS ON DISPOSER.
25 PROVIDE SERVICE OUT OF WALL AT 56" A.F.F., CONNECTTO TERMINALS ON ICE MAKER AT 74" A.F.F...
26 PROVIDE RECEPTACLE AND DATA OUTLET AT 52" A.F.F.FOR KRONOS TIMECLOCK.
1 PROVIDE FLUSH 30A/2P ECB WITH STAINLESS STEELCOVER AND DOUBLE GASKET.
2 PROVIDE FLUSH 20A/3P ECB WITH STAINLESS STEELCOVER AND DOUBLE GASKET.
3 PROVIDE SERVICE AT 16" A.F.F. FOR POWER SOAKER.MAKE FINAL CONNECECTION ACCORDING TOMANUFACTURERS REQUIREMENT.
4 MAKE ALL CONNECTIONS AS REQUIRED TO DISPOSERCONTROL PANEL, DISPOSER, AND SOLENOID VALVE.MOUNT CONTROL PANEL UNDERNEATH FRONT OF PREP.TABLE PER MANUFACTURES RECOMMENDATIONS.COORDINATE EXACT REQUIREMENTS
5 DOORBELL PUSH BUTTON. MOUNT AT 42 IN. A.F.F.PROVIDE SQUARE D MODEL KR1RH13 WITH STAINLESSSTELL FACEPLATE.
6 DOOR BELL, EDWARDS MODEL 340-4N5 120 VOLT GRAY BELL IN #348 EDWARDS BACKBOX. MOUNT AT 80 IN. A.F.F
7 PROVIDE SERVICE OUT OF WALL FOR FLY FAN. COORDINATE EXACT MOUNTING HEIGHT. INTERLOCK FAN
WITH LIMIT SWITCH PROVIDED WITH UNIT SO THAT FAN WILL TURN ON WHEN DOOR IS OPEN AND TURN OFF WHEN
DOOR IS CLOSED. LOCATE 30A/2P DISCONNECT ABOVEACCESSIBLE CEILING.
8 PROVIDE PASS & SEYMORE PS60SS-NON FUSIBLE, NONMETALLIC DISCONNECT. MAKE ALL FINAL CONNECTIONSTO EQUIPMENT.
9 MAKE CONNECTION TO FREEZER/COOLER LIGHTS ANDDOOR HEATERS AS REQUIRED BY UNIT MANUFACTURER.
10 EYS SEAL OFF FITTING.
11 MOUNT OUTLET ON WALL ABOVE OPENING.(AT 88" A.F.F.)COORDINATE EXACT LOCATION. PROVIDE 3#10.
12 MOUNT OUTLET ON WALL ABOVE OPENING (AT 88" A.F.F.).COORDINATE EXACT LOCATION.
13 MAKE FINAL CONNECTION TO UDS/UTILITY WALL.COORDINATE EXACT ELECTRICAL REQUIREMENTS WITHEQUIPMENT BEING INSTALLED.
F ALL EXPOSED CONDUITS SHALL BE GALVANIZED RIGIDSTEEL.
G COORDINATE EXACT LOCATIONS OF WALK IN COOLER &FREEZER COMPRESSOR LOCATIONS WITH ARCHITECT.
H PROVIDE CORD AND PLUG FOR EACH PIECE OF KITCHENEQUIPMENT LOCATED BENEATH HOOD.
I OUTLETS IN KITCHEN LOW WALLS SHALL BE MOUNTEDHORIZONTAL.
J INTERLOCK RANGE HOOD FIRE SUPPRESSION SYSTEMWITH GAS SOLENOID VALVE AND SHUNT TRIPBREAKERS SERVING EQUIPMENT UNDER THE HOOD,SUCH THAT UPON SYSTEM ACTIVATION ALL POWER ISSHUT OFF. RANGE HOOD EXHAUST FAN SHALL REMAINON AND MAKE-UP AIR SHALL BE SHUT OFF. ALSOINTERLOCK WITH FIRE ALARM SYSTEM SUCH THAT AGENERAL ALARM IS SOUNDED UPON SYSTEMACTIVATION.
A ALL EXPOSED OUTLETS IN KITCHEN AND SERVING AREASHALL BE CAST METAL AND WATER PROOF.
B ALL FLEXIBLE CONDUIT SHALL BE WATERPROOF.
C WHERE KITCHEN EQUIPMENT SHOP DRAWINGS CALLFOR DIRECT CONNECTION AND A RECEPTACLE ISSHOWN ON THE DRAWING, PROVIDE RECEPTACLE,PLUG, AND CORDSET.
D PROVIDE EYS SEAL OFF FITTINGS AT ALL FREEZER ANDCOOLER PENETRATIONS.
E BEFORE ROUGHING IN ANY OUTLETS OR ORDERING ANYRECEPTACLES, PLUGS, CORD SETS, DISCONNECTS, ORANY ITEMS NECESSARY FOR THE CONNECTION OFKITCHEN EQUIPMENT. THE CONTRACTOR SHALLCONSULT THE SHOP DRAWINGS FOR THE EQUIPMENTACTUALLY BEING FURNISHED (UNDER THE CONTRACTOR BY THE OWNER) FOR THE PROJECT AND SHALLPROVIDE AND INSTALL DEVICES. CIRCUITS AND ANYOTHER APPURTENANCES COMPATIBLE WITH THEEQUIPMENT FURNISHED SHALL BE PROVIDED AT NOCOST TO THE OWNER.
(THIS SHEET ONLY)GENERAL NOTES:
D ALL KITCHEN ELECTRICAL REQUIREMENTS SHALL BEVERIFIED WITH EQUIPMENT PURCHASED AND INSTALLEDPRIOR TO ROUGH IN OF ANY OUTLET.
E ALL 5-15R AND 5-20R RECEPTACLES SHALL BE GFCI TYPE.
A REFER TO SECTION 260120 FOR THE COORDINATIONAFFIDAVIT THAT MUST BE SUBMITTED AND APPROVEDBEFORE MATERIALS MAY BE ORDERED.
B THE DESIGN IS BASED ON SINGLE POINT CONNECTIONS TOALL EQUIPMENT, UNLESS NOTED OTHERWISE.
C DISCONNECTS ARE SHOWN AS 30A/3P/3R ETC. IF ARECEPTACLE IS INDICATED, COORDINATE NEMACONFIGURATION WITH EQUIPMENT INSTALLED.
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
1/4" = 1'-0"8/7
/2015 3
:29:0
2 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
7-2
0-2
015.r
vt
E5.02
ELECTRICALLARGE SCALEPLANS
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
1/4" = 1'-0"E5.02
LARGE SCALE - CLASSROOM TYPE B - POWER & SYSTEM2
1/4" = 1'-0"E5.02
LARGE SCALE - CLASSROOM TYPE A - POWER & SYSTEMS3
1/4" = 1'-0"E5.02
LARGE SCALE - COMPUTER CLASSROOM - POWER & SYSTEMS4
1/4" = 1'-0"E5.02
LARGE SCALE - CLASSROOM TYPE C - POWER & SYSTEMS11
1. MOUNT BOX FOR AUDIO VISUAL CONNECTIONS AT 48" AFF.SEE DETAIL FOR BOX SIZE, CONFIGURATION AND CONDUITREQUIREMENTS.
(THIS SHEET ONLY)NOTES:
1/4" = 1'-0"E5.02
LARGE SCALE - CLASSROOM TYPE D - POWER & SYSTEMS5
A COORDINATE LOCATIONS OF OUTLETS WITH ARCHITECT, SEEDETAIL. 2/E7.01.
(THIS SHEET ONLY)GENERAL NOTES:
REVISION SCHEDULE
DATE DESCRIPTION
x1
x4 x4 x4 x4
x4 x4 x4 x4
x1 x4
x1
x4
x4
x1
x1
x4
x1
x4
x4
x1
x1
x4
X 13' - 11"11' - 11"
X 12' - 0"10' - 0"
P
P
P
P FACPP
X 12' - 0"10' - 0"
CC
C
C
AV
DATA
1113
NOTE 1
NOTE 2
NOTE 2
NOTE 2
NOTE 3
TGB
24
6
8
10
12 14,16 22
20
1824
26
28
L1A- 1820 22
L1A- 24 6
L1A- 14,16
L1A- 810 12
L1A- 2426 28
DATA
1418
NOTE 1
NOTE 3
NOTE 2
NOTE 2
NOTE 2
TGB66
54
56
58
60
62
64
72
70
68
74,7652
L1C- 5254 56
L1C- 6466
L1C- 5860 62L1C- 68
70 72
L1C- 74,76
MDF
1303
TB
NOTE 4
NOTE 2
NOTE 2
NOTE 2
NOTE 2
SERVERS
FIBER
COPPER
INTERCOM
FACPIACP
NOTE 3
NOTE 3
NOTE 1
NOTE 3
TMGB
CABINET FOR INTERCOMSHALL BE PROVIDED BYINTERCOM SYSTEM VENDORBUT SHALL MATCH OTHERTHREE CABINETS.
26
28,30242220
18
16
14
12
10
32
34
36
5452
50
48
4644
4038
L1B- 1012 14
L1B- 1618 20
L1B- 2224 26
L1B- 28,30
L1B- 3234 36
40L1B- 38
L1B- 4446
L1B- 4850
L1B- 5254
CEILING
WHITEBOARD
QUADRUPLEX RECEPTACLE(18"AFF)
TURN OUT ABOVE CEILING WITH 90DEGREE ELBOW. TERMINATE WITHARLINGTON BUSHING.(TYPICAL)
SPEAKER CABLEPROVIDED BY OWNER
FRONT LEFTSPEAKER
OWNER PROVIDED
FRONT RIGHTSPEAKER
OWNER PROVIDED
SPEAKER CABLEPROVIDED BY OWNER
BACK LEFTSPEAKER
OWNER PROVIDED
FRONT BACKSPEAKER
OWNER PROVIDED
POWER BELOWWHITEBOARD
DOUBLE DUPLEX RECEPTACLE FORPROJECTOR, MOUNTED IN KNOCKOUT OF THE
PROJECTOR MOUNT PLATE. (WALL MOUNTED INMUSIC ROOM FOR SHORT THROW PROJECTOR)
TWO 1-1/2"C. STUBBED ABOVEACCESSIBLE CEILING FORCABLES
CEILING MOUNTED DATA PROJECTOR,FURNISHED BY OWNER. INSTALLED,CONNECTED, PROGRAMMED AND SET UPBY CONTRACTOR. COORDINATE EXACTLOCATION OF PROJECTOR WITH OWNERSREPRESENTATIVE.
A/V OUTLET AT TEACHER'S DESK. (48"AFF). 6"SQUARE, 3-1/2" DEEP OUTLET WITH THREE GANGPLASTER RING. FACEPLATE SHALL BE CABLES TOGO 60039. SEE SPECIFICATIONS PROVIDE USBEXTENDER AND PATCH CORDS PER SPECS.
NOTE:CONTRACTOR SHALL PROVIDE RECEPTACLES, OUTLETBOXES AND RACEWAYS. IT DEPARTMENT TO PROVIDECABLING, FACEPLATES, CONTROLLERS, PROJECTOR ANDMOUNT. CONTRACTOR SHALL INSTALL ONE CLASSROOMCOMPLETE AS A MOCK UP FOR THE OWNER TO REVIEWAND APPROVE PRIOR TO ROUGH IN OF ANY ADDITIONALCLASSROOMS.
THREE(3) CAT 6 CABLES TODATA RACK (18" AFF)
LADDER
1st LEVEL
48"
6"
1st LEVEL
TO PANELBOARD
NOTE 1:
ADJACENT TO SPRINKLER HEAD PER N.F.P.A.
SUMP PUMP
SUMP PUMP PIT
12" GRATE ELEVATOR SHAFTFINISHED FLOOR
NOTE 1
GFI RECEPTACLEIN FS BOX -UNSWITCHED
LIGHT FIXTURE, SEE PLANSFOR MARK & LOCATION
SWITCH IN FS BOX, LOCATEADJACENT TO LADDER ACCESS.
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
As indicated8/7
/2015 3
:29:0
7 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
7-2
0-2
015.r
vt
E5.03
ELECTRICALLARGE SCALEPLANS
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
1/4" = 1'-0"E5.03
LARGE SCALE - DATA 1113 POWER & SYSTEMS1 1/4" = 1'-0"E5.03
LARGE SCALE - DATA 1418 POWER & SYSTEMS2 1/4" = 1'-0"E5.03
LARGE SCALE - MDF 1309 POWER & SYSTEMS4
1/8" = 1'-0"E5.03
TYPICAL WALL FIELD DETAIL FOR DEVICE LAYOUT FOR CLASSROOMS5
1/8" = 1'-0"E5.03
ELEVATOR ELEVATION - ELECTRICAL6 1/8" = 1'-0"E5.03
ELEVATOR ELEVATION - FIRE ALARM7 1/8" = 1'-0"E5.03
ELEVATOR EQUIPMENT ROOM DETAIL8
1/4" = 1'-0"E5.03
LARGE SCALE - DATA 2419-1 POWER & SYSTEMS9
1/4" = 1'-0"E5.03
LARGE SCALE - LAB POWER & SYSTEMS10
1. PROVIDE 4#10 HOMERUN, 3/4"C. FOR FUTURE UPS POWER.
2. RECEPTACLE SHALL BE LOCATED AT TOP OF TELECOMMUNICATIONSRACK. COORDINATE EXACT LOCATION WITH TELECOMUNICATIONSINSTALLER.
3. PLYWOOD BACKBOARD: PROVIDE 3/4" THICK, FIRE RETARDANT PLYWOODBACKBOARD, COAT PLYWOOD WITH TWO COATS LIGHT GRAY FIRERETARDANT PAINT. PROVIDE 3/4" X 3/4" ALUMINUM ANGLE FRAME AFTERPAINTING.
4. TELEPHONE DEMARK: PROVIDE TELEPHONE CABLING FOR THE FOLLOWING:EMERGENCY 911 BACKUP LINES (2), FIRE ALARM (1), BURGLAR ALARM (1),ELEVATOR (2).
5. MOUNT BOX FOR AUDIO VISUAL CONNECTIONS AT 48" A.F.F. SEE DETAIL FORBOX SIZE, CONFIGURATION AND CONDUIT REQUIREMENTS.
6. NOT USED.
7. MOUNT OUTLETS IN KNEE SPACE OF CASEWORK IN AN ACCESSIBLE LOCATION.ALL CONDUIT SHALL BE CONCEALED.
8. PROVIDE 1 1/4" CONDUIT FROM DATA OUTLET TO NEAREAST WALL, THENTO ABOVE ACCESSIBLE CEILING.
(THIS SHEET ONLY)NOTES:
A COORDINATE LOCATIONS OF OUTLETS WITH ARCHITECT, SEEDETAIL. 2/E7.01.
(THIS SHEET ONLY)GENERAL NOTES:
REVISION SCHEDULE
DATE DESCRIPTION
GROUND CONNECTION FOR EQUIPMENT.COMPRESSION LUG BOLTS AND WIRE.
MOUNTING BRACKET,STAINLESS STEEL
POLYESTER/FIBERGLASS.RED STANDOFF INSULATOR,
FRONT ELEVATION
A
WALL CONSTRUCTION(TYPICAL).
SUITABLE FORWALL ANCHOR SECTION "A-A"
A
19" x 6" x 1/4" THICK COPPER GROUND BUS
3/8" MOUNTING BOLT.
1" OFFSET.2"
1/4"
NOTE: LOCATION INDICATEDAS "TMGB" IN MDF ROOMAND "TGB" IN IDF ROOMS.
STK
STK
CORE12X4
APOGEECA-4000
CD PLAYER
1-WIRELESS MIC
2-WIRELESS MIC
1- MIC
2- MIC
3- MIC
INPUTS
AFI-3SPEAKER
AFI-3SPEAKER
WILLIAMS SOUND
ASSISTED LISTENING SYSTEM
AFI-3SPEAKER
AFI-3SPEAKER
SCHOOL WIDE INTERCOM
4
TO NEAREST 120 VOLT, 20 AMPUNSWITCHED RECEPTACLECIRCUIT
MOTOR RATEDSWITCH
3#12, 1 / 2 IN. C
INTERIOR VIEW
1 1
22
3
1/2" C. 1/2" C.
5 5
THIS DRAWING IS INTENDED TO INDICATE CONDUIT INFRASTRUCTUREREQUIREMENT ONLY. COORDINATE EXACT REQUIRED COMPONENTSWITH ARCHITECTURAL DOOR SPECIFICATIONS. PROVIDE ALL CONDUITAND BOXES FOR COMPLETE ACCESS CONTROL INSTALLATION.
3#12, 1/2"C.(FLEXIBLECONDUIT)
NOTES:1
2
4
(ACCESS CONTROL CONNECTIONS)
DOOR POSITION SWITCH.
CURRENT TRANSFER HINGE
POWER SUPPLY.
CARD READER.
DELAYED EGRESS SYSTEM - NORMALLY CLOSED FIRE ALARMRELAY REQUIRED, PLUGNPLAY. NORMALLY CLOSED FIRE ALARMRELAY REQUIRED FOR THE DELAYED EGRESS APPLICATION.
3
5
TO MDF/IDF
PROVIDE 12 CONDUCTOR20 GAUGE WIRE WITH THEFOLLOWING COLORS: BLACK,RED, WHITE, GREEN, ORANGE,BLUE, BROWN, YELLOW, PINK,GRAY, TAN AND VIOLET.
STK
STK
CORE
12X4
BOGEN
M-CLASS
CD PLAYER
1-WIRELESS MIC
2-WIRELESS MIC
1- MIC
2- MIC
3- MIC
INPUTS
WILLIAMS SOUND
ASSISTED LISTENING SYSTEM
s
s
ALL SPEAKERS IN CAFETERIA SHALLBE BOGEN "HFCS1" OR EQUALSPEAKERS. SEE PLAN FOR QUANTITYOF SPEAKERS
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
1/16" = 1'-0"8/7
/2015 3
:30:0
8 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
7-2
0-2
015.r
vt
T3.11
FIRST FLOORPLAN - WIREMANAGEMENT
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
1/16" = 1'-0"T3.11
FIRST FLOOR PLAN - WIRE MANAGEMENT1
IN OPEN STRUCTURE AREASAND IN SPACES WITH HARDCEILILNGS, LOW VOLTAGECABLING SHALL BE ROUTEDIN CONDUIT TO CABLE TRAY.
REVISION SCHEDULE
DATE DESCRIPTION
A
B
C
D
E
F
G
H
I
K
J
NOTES: (J-HOOK DETAIL)RESOURCE ROOM-1
2405-1
RESOURCE ROOM-1
2401-1
STAIR
1120
STORAGE-1
2427-1 STORAGE-1
2407-1
STORAGE
2410
JAN-1
2420-1
DATA
2419
ELEC-1
2418-1
CONF-1
2433-1
CORRIDOR
2500
DATA CONF ROOM-1
2429-1
WORKROOM-1
2430-1
?
?
STORAGE-1
2514-1
RESOURCE ROOM-1
2417-1
STOR-1
2411-1
STAIR
1135
CORRIDOR-1
2600-1
STORAGE
2614
CORRIDOR-1
2402-1
OFFICE-1
2416-1
OFFICE-1
2414-1
STOR-1
2412-1
SCIENCE CLASSROOM
2409
GIFTED/STEM LAB
2408
CORRIDOR
2400
STAIR-1
2406-1
OFFICE-1
2415-1
ELEV-1
2413-1
TLT-1
2431-1
TLT-1
2432-1
HALL-1
2510-1
TLT-1
2510.2-1
5TH GRADE CLASSROOM
2512
5TH GRADE CLASSROOM-1
2508-1
HALL-1
2509-1
TLT-1
2509.2-1
5TH GRADE CLASSROOM
2511
5TH GRADE CLASSROOM-1
2507-1
HALL-1
2503-1
TLT-1
2503.2-1
5TH GRADE CLASSROOM
2505
4TH GRADE CLASSROOM-1
2501-1
HALL-1
2604-1
TLT-1
2604.2-1
3RD GRADE CLASSROOM
2602
3RD GRADE CLASSROOM-1
2606-1
TLT-1
2604.1-1
HALL-1
2610-1
TLT-1
2610.2-1
GIFTED CLASSROOM
2608
GIFTED CLASSROOM
2612
TLT-1
2610.1-1
HALL-1
2609-1
TLT-1
2609.2-1
GIFTED CLASSROOM
2607
GIFTED CLASSROOM-1
2611-1
TLT-1
2609.1-1
HALL-1
2423-1
TLT-1
2423.2-1
3RD GRADE CLASSROOM
2421
3RD GRADE CLASSROOM-1
2425-1
TLT-1
2423.1-1
HALL-1
2424-1
TLT-1
2424.2-1
4TH GRADE CLASSROOM
2422
4TH GRADE CLASSROOM-1
2426-1
TLT-1
2424.1-1
HALL-1
2504-1
TLT-1
2504.2-1
5TH GRADE INCLUSION CLASSROOM
2506
4TH GRADE INCULSION CLASSROOM-1
2502-1
TLT-1
2504.1-1
HALL-1
2603-1
TLT-1
2603.2-1
3RD GRADE INCLUSION CLASSROOM
2601
TLT-1
2603.1-1
ESL CLASSROOM-1
2605-1
TLT
2403
TLT
2404
PROVIDE 6-4"SLEEVES TODATA ROOMBELOW.
UP TO 4" CONDUIT
NOTE:WHERE CONDUIT IS USED AS A SLEEVE FOR ROUTING LOW VOLTAGE CABLESTHROUGH A RATED WALL, LOCATE CONDUCTORS IN CENTER OF SLEEVE ANDFILL OPENING WITH NON HARDENING FIRE RATED PUTTY AT EACH END.
WHERE USED AS SLEEVEFOR LOW VOLTAGECABLING,EXTEND CONDUIT 6"BEYONDWALL AND PROVIDE NYLONBUSHINGS ON BOTH ENDS.
ALL J- HOOKS SHALL BE SPACED NO MORE THAN 48 INCHES APART AND NOMORE THAN 12 INCHES FROM THE CORNER OF ANY SPACE.
PROVIDE J-HOOKS NO MORE THAN 12 INCHES AWAY FROM CONDUIT SLEEVES.
WHERE J-HOOKS ARE 2 OR MORE ROWS: SPACING BETWEEN THE ROWS SHALLBE 12 INCHES.
CONDUIT SLEEVES SHALL BE AT THE SAME LEVEL AS THE ROWS OF J-HOOKS.
FIRE SEAL AROUND ALL CONDUIT SLEEVES AS SHOWN IN CONDUIT PENTRATIONDETAILS. SEE ARCHITECTURAL SHEET FOR REQUIRED RATINGS.
COORDINATE THE EXACT LEVEL OF J-HOOKS AND CONDUIT SLEEVES WITH OTHERTRADES PRIOR TO ROUGHING.
J-HOOKS SHALL NOT BE SUPPORTED BY GYPSUM WALL BOARD. J-HOOKS SHALL BESUPPORTED BY BLOCK WALL OR STUD. SEE ARCHITECTURAL PLAN FOR WALLMATERIALS.
ALL CABLING SHALL BE NEATLY BUNDLED UTILIZING VELCRO TIE WRAPS ATMINIMUM 5' INTERVALS.
J-HOOKS SHALL SUPPORT CABLING FOR: FIRE ALARM, INTERCOM, DATA, TELEPHONE,CCTV, INTRUSION AND TELEVISION DISTRIBUTION.
J-HOOKS SHALL SUPPORT A SINGLE SYSTEM - CABLING SHALL NOT BE INTERMINGLED.
PROVIDE QUANTITY OF J-HOOKS AS REQUIRED FOR CABLING NOTED ON DRAWINGS,DO NOT EXCEED J-HOOK CAPACITY.
4"
6"
UP TO 4" EMT OR STEEL PIPE
NOTE:WHERE CONDUIT IS USED AS A SLEEVE FOR ROUTING LOW VOLTAGE CABLESTHROUGH A RATED WALL, LOCATE CONDUCTORS IN CENTER OF SLEEVE ANDFILL OPENING WITH NON HARDENING FIRE RATED PUTTY AT EACH END OFSLEEVE.
WHERE USED AS SLEEVEFOR LOW VOLTAGECABLING,EXTEND CONDUIT 6"BEYONDWALL AND PROVIDE NYLONBUSHINGS ON BOTH ENDS.
SAUSSY ENGINEERING400 E. JOHNNY MERCER BOULEVARDSAVANNAH, GA 31410
CIVIL ENGINEERS:
COASTLINE CONSULTINGSERVICES138 CANAL STREETPOOLER, GA 31322
FTE: 750 / 900 CORE
1500
Cogdell MendralaArchitects
WOLVERTON & ASSOCIATES, INC.7 CONGRESS STREETSAVANNAH, GA 31401
ELECTRICAL & COMMUNICATIONS ENGINEER:
SUSTAINABLE DESIGNCONSULTANTS
415 BONAVENTURE DRIVETHUNDERBOLT, GA. 31404
1400
1600
1100
1300
1200
1000
FACILITY CODE: 625-0122
NOT TO SCALE9/2
/2015 7
:37:4
9 P
ME
:\$A
CT
IVE
JO
BS
\2014 1
017 -
MA
Y H
OW
AR
D\R
EV
IT M
OD
ELS
\20141017 E
LE
C-G
clark
9-2
-2015.r
vt
T4.11
ACCESSCONTROLDETAILS
GJCAUGUST 2015
1402
MA
Y H
OW
AR
D E
LE
ME
NT
AR
Y
RE
PL
AC
EM
EN
T S
CH
OO
L
115 W
ILM
ING
TO
N IS
LA
ND
RO
AD
SA
VA
NN
AH
, G
EO
RG
IA 3
1410
REVISION SCHEDULE
DATE DESCRIPTION
9-04-2015 Addendum No. 1
NOT TO SCALET4.11
1 ACCESS CONTROL DETAILS
1
COORDINATE CABLING WITH SECTION 087100. EXTEND ALL PREWIREDCABLES IN HOLLOW METAL FRAMES, INCLUDING CONDUIT, TO THEJUNCTION BOX LOCATIONS SHOWN. DO NOT CUT ANY EXCESS CABLING.SIMPLY COIL IT AND TIE WRAP TO JUNCTION BOX FOR TERMINATION BYOTHERS.
ELECTRICAL CONTRACTOR RESPONSIBLE FOR ALL 120VAC CONNECTIONSTO THE POWER SUPPLIES.
SEE ARCHITECTURAL FLOOR PLAN SHEETS FOR ALL DOOR NUMBERS.
SEE DETAIL 1/T0.01 FOR ADDITIONAL REQUIREMENT FOR ALL ACCESSCONTROL DOORS.
