88
VERSION 2020-08-13 DETAILS NORDIC LAM+ NORDIC X-LAM NS-DS2 ENGLISH Mass Timber Construction STRUCTURAL DETAILS Mass Timber Construction STRUCTURAL DETAILS
VERSION2020-08-13
DE TA IL SNOR DIC L A M+ NOR DIC X-L A M
NS-DS2ENGLISH
Mass Timber Construction
STRUCTURAL DETAILS
Mass Timber Construction
STRUCTURAL DETAILS
Nordic Structures is the leading innovator in mass timber
construction. Its resource comes from responsibly
managed lands within the regional boreal forest. Vertical
integration, from forest to structure, bolstered by Nordic’s
experienced design and development team, ensures
consistent quality and unparalleled level of service.
514-871-8526 1 866 817-3418
HEAD OFFICE
Nordic Structures 100-1100 Canadiens-de-Montréal Avenue Montréal, Québec H3B 2S2
www.nordic.ca
GENERAL INFORMATION
TECHNICAL SUPPORT
ABOUT NORDIC
nordic .ca i
12
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
STRUCTURE
MECHANICAL, ELECTRICAL, AND PLUMBING
ii General Notes iii List of Details v Nordic X-Lam (CLT) vi Nordic Lam+ (glulam)
TABLE OF CONTENTS
nordic .ca ii
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
1.0 General
1.1 This document supersedes all previous versions. For the latest version, consult nordic.ca or contact Nordic Structures.
1.2 The information contained in this document is provided for information purposes only. This information should not be used for any application without examination and verification of its accuracy, suitability and applicability by a licensed engineer, architect or other professional. Nordic Structures does not guarantee that the information is suitable for any general or particular use, and assumes no responsibility for the use, application of and / or reference to the information.
1.3 All dimensions are in millimetres (mm), unless otherwise noted.
1.4 For more information, consult nordic.ca or contact Nordic Structures.
2.0 Design of connections
2.1 The design of connections, including fire resistance if required, shall be in accordance with CSA O86-14, Engineering design in wood.
2.2 The design of connections should include considerations for structural and service performance, such as resistance, minimum distances, dimensional changes, durability, erection and fire safety, among others, as well as taking into account architectural requirements.
2.3 The connections shown in this document are provided for information purposes only, and conceptually. Note that many possibilities and variants are possible.
GENERAL NOTES
nordic .ca iii
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
Structure Category Title Drawing Date PageStructure, GL-CLT Continuous Floor Slab on Beam NS-DS2001 2020-02-01 1.1Structure, GL-CLT Single Floor Slab on Beam NS-DS2002 2020-02-01 1.2Structure, GL-CLT Face-mount Hanger NS-DS2003 2020-02-01 1.3Structure, GL-CLT Face-mount Hanger with Concealed Flanges NS-DS2067 2020-02-01 1.4Structure, GL-CLT Knife Plate NS-DS2004 2020-02-01 1.5Structure, GL-CLT Knife Plate with Cap NS-DS2005 2020-02-01 1.6Structure, GL-CLT Screwed Beam to Column NS-DS2006 2020-02-01 1.7Structure, GL-CLT Beam to Column with Knife Plate NS-DS2007 2020-02-01 1.8Structure, GL-CLT Pocket for Beam NS-DS2008 2020-02-01 1.9Structure, GL-CLT Through Pocket for Beam NS-DS2009 2020-02-01 1.10Structure, Wall-Foundation Wall to Sill Plate, Screws NS-DS2010 2020-02-01 1.11Structure, Wall-Foundation Wall to Sill Plate, Nailed Steel Plate NS-DS2011 2020-02-01 1.12Structure, Wall-Foundation Wall to Sill Plate, Holdown NS-DS2012 2020-02-01 1.13Structure, Wall-Foundation Wall to Sill Plate, Steel Angle NS-DS2013 2020-02-01 1.14Structure, Wall-Foundation Wall to Foundation, Holdown NS-DS2014 2020-02-01 1.15Structure, Wall-Foundation Wall to Foundation, Nailed Steel Angle NS-DS2015 2020-02-01 1.16Structure, Wall-Foundation Wall to Foundation, Screwed Steel Angle NS-DS2016 2020-02-01 1.17Structure, Wall-Foundation Wall to Foundation, Nailed Steel Angle and Steel C Shape NS-DS2068 2020-02-01 1.18Structure, Wall-Foundation Wall to Foundation, Nailed C Shape NS-DS2017 2020-02-01 1.19Structure, Floor/Roof-Wall Ledger NS-DS2018 2020-02-01 1.20Structure, Floor/Roof-Wall Steel Angle NS-DS2019 2020-02-01 1.21Structure, Floor/Roof-Wall Screwed Floor/Roof Slab to Wall NS-DS2020 2020-02-01 1.22Structure, Floor/Roof-Wall Screwed Wall to Continuous Floor Slab to Wall NS-DS2021 2020-02-01 1.23Structure, Floor/Roof-Wall Screwed Wall to Single Floor Slab to Wall NS-DS2022 2020-02-01 1.24Structure, Floor/Roof-Wall Wall to Floor Slab with Steel Square to Wall NS-DS2023 2020-02-01 1.25Structure, Floor/Roof-Wall Wall to Floor Slab with Steel Square to Notched Wall NS-DS2024 2020-02-01 1.26Structure, Floor/Roof-Wall Sloped Roof Slab to Wall NS-DS2025 2020-02-01 1.27Structure, Lintel CLT Lintel NS-DS2026 2020-02-01 1.28Structure, Lintel Glulam Lintel NS-DS2027 2020-02-01 1.29Structure, Panel-Panel Butt Joint, One row of Nails NS-DS2029 2020-02-01 1.30Structure, Panel-Panel Butt Joint, Two Rows of Nails NS-DS2030 2020-02-01 1.31Structure, Panel-Panel Butt Joint, 45° Screws NS-DS2069 2020-02-01 1.32Structure, Panel-Panel Half-Lap Joint NS-DS2031 2020-02-01 1.33Structure, Wall-Wall Corner Joint with 90° Screws NS-DS2032 2020-02-01 1.34Structure, Wall-Wall Notched Corner Joint with 90° Screws NS-DS2033 2020-02-01 1.35Structure, Wall-Wall Corner Joint with 45° Screws NS-DS2034 2020-02-01 1.36Structure, Wall-Wall T-Joint with 90° Screws NS-DS2035 2020-02-01 1.37Structure, Wall-Wall T-Joint with 45° Screws NS-DS2036 2020-02-01 1.38Structure, Base Plate Base Plate with Steel Square NS-DS2037 2020-02-01 1.39Structure, Base Plate Base Plate with Knife Plate and Four Mechanical Anchors NS-DS2038 2020-02-01 1.40
LIST OF DETAILS
nordic .ca iv
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
Structure (continued) Category Title Drawing Date PageStructure, Base Plate Base Plate with Knife Plate and Four Hidden Mechanical Anchors NS-DS2039 2020-02-01 1.41Structure, Base Plate Two-storey Base Plate with Knife Plate NS-DS2040 2020-02-01 1.42Structure, Base Plate Two-storey Base Plate with Glued-in Rod NS-DS2041 2020-02-01 1.43Structure, Base Plate Two-storey Base Plate with Glued-in Rod and Pocket NS-DS2042 2020-02-01 1.44Structure, Base Plate Two-storey Base Plate with Glued-in Rod and Half-height Pocket NS-DS2070 2020-02-01 1.45Structure, Beam-Column Double Member Beam with Spacing NS-DS2043 2020-02-01 1.46Structure, Beam-Column Double Member Beam Without Spacing NS-DS2044 2020-02-01 1.47Structure, Beam-Column Knife Plate with Shear Key NS-DS2045 2020-02-01 1.48Structure, Beam-Column Knife Plate with Shear Key and Bearing Plate NS-DS2046 2020-02-01 1.49Structure, Beam-Column Single Beam, Bridle Joint NS-DS2047 2020-02-01 1.50Structure, Beam-Column Continuous Beam, Bridle Joint NS-DS2048 2020-02-01 1.51Structure, Beam-Column Half-Lap Joint NS-DS2049 2020-02-01 1.52Structure, Beam-Column Face-mount Hanger NS-DS2050 2020-02-01 1.53Structure, Beam-Column Face-mount Hanger with Concealed Flanges NS-DS2051 2020-02-01 1.54Structure, Beam-Column Beam on Cleat NS-DS2053 2020-02-01 1.55Structure, Girt-Column Knife Plate NS-DS2055 2020-02-01 1.56Structure, Girt-Column Steel Plates NS-DS2056 2020-02-01 1.57Structure, Girt-Column 45° Screws NS-DS2057 2020-02-01 1.58Structure, Joist-Beam Nailed Face-mount Hanger NS-DS2058 2020-02-01 1.59Structure, Joist-Beam Nailed Face-mount Hanger with Concealed Flanges NS-DS2059 2020-02-01 1.60Structure, Joist-Beam Bolted Face-mount Hanger NS-DS2060 2020-02-01 1.61Structure, Joist-Beam Knife Plate with Saddle NS-DS2061 2020-02-01 1.62Structure, Joist-Beam Knife Plate NS-DS2062 2020-02-01 1.63Structure, Joist-Beam 45° Screws - Option 1 NS-DS2063 2020-02-01 1.64Structure, Joist-Beam 45° Screws - Option 2 NS-DS2064 2020-02-01 1.65Structure, Joist-Beam Joist on Beam with 45° Screws and Glued-In Rod NS-DS2065 2020-02-01 1.66Structure, Hybrid Decking to Steel Beam NS-DS2066 2020-02-01 1.67
Mechanical, electrical, and plumbing Category Title Drawing Date PageMechanical, Electrical, and Plumbing Vertical, Double-Member Beam NS-DS2501 2020-02-01 2.1Mechanical, Electrical, and Plumbing Horizontal, Pre-Machined Opening NS-DS2502 2020-02-01 2.2Mechanical, Electrical, and Plumbing Horizontal, Electrical Box with 38 mm x 64 mm Wood Studs NS-DS2503 2020-02-01 2.3Mechanical, Electrical, and Plumbing Horizontal, Raised Floor NS-DS2504 2020-02-01 2.4Mechanical, Electrical, and Plumbing Horizontal, Suspended Ceiling NS-DS2505 2020-02-01 2.5Mechanical, Electrical, and Plumbing Horizontal, Joist on Beam NS-DS2506 2020-02-01 2.6Mechanical, Electrical, and Plumbing Horizontal, Bevelled Beam NS-DS2507 2020-02-01 2.7Mechanical, Electrical, and Plumbing Multi-Residential Unit Diagram, Option 1 NS-DS2508 2020-02-01 2.8Mechanical, Electrical, and Plumbing Multi-Residential Unit Diagram, Option 2 NS-DS2509 2020-02-01 2.9
LIST OF DETAILS (CONTINUED)
nordic .ca v
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
89-3s
105-3s
143-5s
175-5s
197-7s
213-7l
244-7s
244-7l
267-9l
3 LAYERS
5 LAYERS
7 LAYERS 9 LAYERS
CLT
NORDIC X-LAM CROSS-LAMINATED TIMBERNordic X-Lam cross-laminated timber is made of at least three orthogonal layers of graded sawn lumber that are laminated by gluing with structural adhesives.
SLABS AND PANELS
Layup combinations 89-3s, 105-3s, 143-5s, 175-5s, 197-7s, 213-7l, 244-7s, 244-7l and 267-9l
Maximum sizes 2.70 × 19.5 m (106-1/4 in. × 64 ft)
Stress grade E1 (L 1950Fb and T No. 3/Stud)
NORDIC X-LAM LAYUP COMBINATIONS
nordic .ca vi
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
DECKING
Thicknesses* 38, 44, 54 and 89 mm (1-1/2, 1-3/4, 2-1/8 and 3-1/2 in.)
Widths 203, 305 and 406 mm (8, 12 and 16 in.)
Lengths Up to 18.9 m (62 ft)
Stress grades ES11, except 89 mm thickness in 20F-ES/CPG
* Larger sizes available upon request
GLULAM
NORDIC LAM+ GLUED-LAMINATED TIMBERNordic Lam+ glued-laminated timber of architectural appearance grade consists of small wood laminations bonded together in parallel using structural adhesives.
BEAMS AND COLUMNS
Widths* 38, 86, 137, 184, 215, 241, 292, 346, 395, 448, 502, 552 and 603 mm (1-1/2, 3-3/8, 5-3/8, 7-1/4, 8-1/2, 9-1/2, 11-1/2, 13-5/8, 15-1/2, 17-5/8, 19-3/4, 21-3/4 and 23-3/4 in.)
Depths* From 67 to 2435 mm (2-5/8 to 95-7/8 in.)
Lengths* Up to 24.4 m (80 ft)
Stress grade 24F-ES/NPG
* Larger sizes available upon request
VERSION2020-08-13
1
DE TA IL SNOR DIC L A M+ NOR DIC X-L A M
NS-DS2ENGLISH
STRUCTURE
nordic .ca 1.1
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Continuous Floor Slab on Beam
-TLC-LG ,erutcurtS
NS-DS2001-CA-enDRAWING
NORDIC X-LAM SLAB
NORDIC LAM BEAM
PARTIALLY THREADED SCREW @ 300 O.C. U.N.O.
nordic .ca 1.2
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= = = =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Single Floor Slab on Beam
-TLC-LG ,erutcurtS
NS-DS2002-CA-enDRAWING
NORDIC X-LAM SLAB
NORDIC LAM BEAM
PARTIALLY THREADED SCREWS@ 300 O.C. U.N.O., STAGGERED
nordic .ca 1.3
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
=
2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Face-mount Hanger
-TLC-LG ,erutcurtS
NS-DS2003-CA-enDRAWING
1-2 mm (GAP)
NORDIC X-LAM WALL
NORDIC LAM BEAM
HANGER
RING SHANK NAIL
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
nordic .ca 1.4
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
=
2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Face-mount Hanger with Concealed Flanges
-TLC-LG ,erutcurtS
NS-DS2067-CA-enDRAWING
1-2 mm (GAP)
NORDIC X-LAM WALL
NORDIC LAM BEAM
HANGER
RING SHANK NAIL
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
nordic .ca 1.5
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Knife Plate
-TLC-LG ,erutcurtS
NS-DS2004-CA-enDRAWING
(a)
RING SHANK NAIL
NORDIC X-LAM WALL
NORDIC LAM BEAM
STEEL DOWEL
STEEL KNIFE PLATE
1-2 mm (GAP)
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
PARTIALLY THREADED SCREW
nordic .ca 1.6
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Knife Plate with Cap
-TLC-LG ,erutcurtS
NS-DS2005-CA-enDRAWING
(a)
NORDIC LAM BEAM
STEEL DOWEL
STEEL KNIFE PLATE
NORDIC X-LAM WALL
1-2 mm (GAP)
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
RING SHANK NAIL
PARTIALLY THREADED SCREW
NORDIC LAM CAP
nordic .ca 1.7
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Screwed Beam to Column
-TLC-LG ,erutcurtS
NS-DS2006-CA-enDRAWING
1-2 mm (GAP)
NORDIC X-LAM WALL
NORDIC LAM COLUMN
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
NORDIC LAM BEAM
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
PARTIALLY THREADED SCREW
PARTIALLY THREADED SCREWS
nordic .ca 1.8
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
(a)
10 m
m (G
AP
)
0.5-1.0 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Beam to Column with Knife Plate
-TLC-LG ,erutcurtS
NS-DS2007-CA-enDRAWING
1-2 mm (GAP)
NORDIC X-LAM WALL
NORDIC LAM COLUMN
STEEL KNIFE PLATE
STEEL DOWEL
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
NORDIC LAM BEAM
PARTIALLY THREADED SCREW @ 300 O.C. U.N.O.
nordic .ca 1.9
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
VAR.
VAR.
2020-02-01
1-2
mm
EA
CH
SID
E (G
AP
)
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Structure, GL-CLT
Pocket for Beam
-
NS-DS2008-CA-enDRAWING
NORDIC X-LAM WALL
NORDIC LAM BEAM
PARTIALLY THREADED SCREWS, STAGGERED
nordic .ca 1.10
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
VAR.
VAR.
2020-02-01
1-2
mm
EA
CH
SID
E (G
AP
)
NORDIC LAM BEAM
NORDIC X-LAM WALL
TITLE
CATEGORY DATE EGAPELACS
Through Pocket for Beam
-TLC-LG ,erutcurtS
NS-DS2009-CA-enDRAWING
PARTIALLY THREADED SCREWS, STAGGERED
nordic .ca 1.11
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Sill Plate, Screws
-noitadnuoF-llaW ,erutcurtS
NS-DS2010-CA-enDRAWING
CONCRETE
MECHANICAL ANCHOR
NON-SHRINK GROUT 25 mm
IMPERMEABLE MEMBRANE
SILL PLATE
NORDIC X-LAM WALL
PARTIALLY THREADED SCREWS@ 300 O.C. U.N.O., STAGGERED
nordic .ca 1.12
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Structure, Wall-Foundation -
NS-DS2011-CA-enDRAWING
Wall to Sill Plate, Nailed Steel Plate
STEEL PLATE
CONCRETE
MECHANICAL ANCHOR
NON-SHRINK GROUT 25 mm
IMPERMEABLE MEMBRANE
SILL PLATE
RING SHANK NAIL
NORDIC X-LAM WALL
nordic .ca 1.13
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
==
==
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Structure, Wall-Foundation -
NS-DS2012-CA-enDRAWING
CONCRETE
RING SHANK NAIL
NORDIC X-LAM WALL
HOLDOWN
SILL PLATE
IMPERMEABLE MEMBRANE
NON-SHRINK GROUT 25 mm
Wall to Sill Plate, Holdown
MECHANICAL ANCHORS
nordic .ca 1.14
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Structure, Wall-Foundation -
NS-DS2013-CA-enDRAWING
CONCRETE
NORDIC X-LAM WALL
RING SHANK NAIL
STEEL ANGLE
SILL PLATE
IMPERMEABLE MEMBRANE
NON-SHRINK GROUT 25 mm
Wall to Sill Plate, Steel Angle
MECHANICAL ANCHORS
nordic .ca 1.15
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
==
==
==
==
==
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
-noitadnuoF-llaW ,erutcurtS
NS-DS2014-CA-enDRAWING
NORDIC X-LAM WALL
RING SHANK NAIL
HOLDOWN
NON-SHRINK GROUT 25 mm
MECHANICAL ANCHOR
CONCRETE
Wall to Foundation, Holdown
IMPERMEABLE MEMBRANE
nordic .ca 1.16
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Foundation, Nailed Steel Angle
-noitadnuoF-llaW ,erutcurtS
NS-DS2015-CA-enDRAWING
POCKET AT ANCHOR LOCATION
CONCRETE
NON-SHRINK GROUT 25 mm
STEEL ANGLE
RING SHANK NAIL
NORDIC X-LAM WALL
MECHANICALANCHOR
CONCRETE
NON-SHRINK GROUT 25 mm
STEEL ANGLE
RING SHANK NAIL
NORDIC X-LAM WALL
MECHANICAL ANCHOR
nordic .ca 1.17
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Foundation, Screwed Steel Angle
-noitadnuoF-llaW ,erutcurtS
NS-DS2016-CA-enDRAWING
POCKET AT ANCHOR LOCATION
Note:1. This assembly detail offers a resistance to forces acting perpendicularlry to the
foundation wall.
MECHANICALANCHOR
NORDIC X-LAM WALL
STEEL ANGLE
NON-SHRINK GROUT 25 mm
CONCRETE
NORDIC X-LAM WALL
STEEL ANGLE
NON-SHRINK GROUT 25 mm
CONCRETE
MECHANICAL ANCHOR
PARTIALLY THREADED SCREW
PARTIALLY THREADED SCREWS, STAGGERED
nordic .ca 1.18
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Foundation, Nailed Steel Angle and Steel C Shape
-noitadnuoF-llaW ,erutcurtS
NS-DS2068-CA-enDRAWING
CONCRETE
NON-SHRINK GROUT 25 mm
STEEL ANGLE
RING SHANK NAIL
NORDIC X-LAM WALL
MECHANICALANCHOR
CONCRETE
NON-SHRINK GROUT 25 mm
STEEL ANGLE
RING SHANK NAIL
NORDIC X-LAM WALL
MECHANICAL ANCHOR
STEEL C SHAPE
STEEL C SHAPE
nordic .ca 1.19
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Foundation, Nailed C Shape
-noitadnuoF-llaW ,erutcurtS
NS-DS2017-CA-enDRAWING
POCKET AT ANCHOR LOCATION
CONCRETE
MECHANICAL ANCHOR
NON-SHRINK GROUT 25 mm
STEEL C SHAPE
RING SHANK NAIL
NORDIC X-LAM WALL
CONCRETE
NON-SHRINK GROUT 25 mm
STEEL C SHAPE
RING SHANK NAIL
NORDIC X-LAM WALL
Note:1. For an exterior wall on foundation, careful consideration should be given to
waterproofing and drainage at the junction between wall and steel C shape.
MECHANICALANCHOR
nordic .ca 1.20
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
45°
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Ledger
-llaW-fooR/roolF ,erutcurtS
NS-DS2018-CA-enDRAWING
NORDIC X-LAM WALL
NORDIC X-LAM SLAB
NORDIC LAM LEDGER
FULLY THREADED SCREW @ 250 O.C. U.N.O.
FULLY THREADED SCREW@ 250 O.C. U.N.O.
PARTIALLY THREADED SCREW@ 250 O.C. U.N.O.
nordic .ca 1.21
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Steel Angle
-llaW-fooR/roolF ,erutcurtS
NS-DS2019-CA-enDRAWING
STEEL ANGLE
RING SHANK NAIL
NORDIC X-LAM SLAB
NORDIC X-LAM WALL
1-2 mm (GAP)
PARTIALLY THREADED SCREW @ 250 O.C. U.N.O.
nordic .ca 1.22
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Screwed Floor/Roof Slab to Wall
-llaW-fooR/roolF ,erutcurtS
NS-DS2020-CA-enDRAWING
NORDIC X-LAM SLAB
NORDIC X-LAM WALL
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
nordic .ca 1.23
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
45°45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Screwed Wall to Continuous Floor Slab to Wall
-llaW-fooR/roolF ,erutcurtS
NS-DS2021-CA-enDRAWING
NORDIC X-LAM SLAB
NORDIC X-LAM WALL
NORDIC X-LAM WALL
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
PARTIALLY THREADED SCREWS @ 300 O.C. U.N.O., STAGGERED
nordic .ca 1.24
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°= =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Screwed Wall to Single Floor Slab to Wall
-llaW-fooR/roolF ,erutcurtS
NS-DS2022-CA-enDRAWING
NORDIC X-LAM WALL
NORDIC X-LAM WALL
NORDIC X-LAMSLAB
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
nordic .ca 1.25
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Floor Slab with Steel Square to Wall
-llaW-fooR/roolF ,erutcurtS
NS-DS2023-CA-enDRAWING
NORDIC X-LAMSLAB
STEEL SQUARE
RING SHANK NAILNORDIC X-LAM WALL
NORDIC X-LAM WALL
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
nordic .ca 1.26
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Wall to Floor Slab with Steel Square to Notched Wall
-llaW-fooR/roolF ,erutcurtS
NS-DS2024-CA-enDRAWING
NORDIC X-LAMSLAB
NORDIC X-LAM WALL RING SHANK NAIL
STEEL SQUARE
1-2 mm(GAP)
FULLY THREADED SCREW @ 300 O.C.
nordic .ca 1.27
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Sloped Roof Slab to Wall
-llaW-fooR/roolF ,erutcurtS
NS-DS2025-CA-enDRAWING
NORDIC X-LAM SLAB
NORDIC X-LAM WALL
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
nordic .ca 1.28
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
CLT Lintel
-letniL ,erutcurtS
NS-DS2026-CA-enDRAWING
NORDIC X-LAM WALL
NORDIC X-LAM LINTEL
PARTIALLY THREADED SCREW
nordic .ca 1.29
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Glulam Lintel
-letniL ,erutcurtS
NS-DS2027-CA-enDRAWING
NORDIC LAM LINTEL
NORDIC X-LAM WALL
PARTIALLY THREADED SCREW
nordic .ca 1.30
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Butt Joint, One row of Nails NS-DS2029-CA-enDRAWING
14
30 30
130120 PLYWOOD
12.7 mm (TYP.)
Structure, Panel-Panel -
GALVANIZED SPIRAL NAIL@ 150 O.C. U.N.O.
nordic .ca 1.31
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= = = = = =
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Butt Joint, Two Rows of Nails NS-DS2030-CA-enDRAWING
14
130120
150 (S.I.C.)
PLYWOOD12.7 mm (TYP.)
Structure, Panel-Panel -
2 ROWS OF GALVANIZED SPIRAL NAILS @ 150 O.C. U.N.O., STAGGERED
nordic .ca 1.32
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
DRAWING
Butt Joint, 45° Screws
-lenaP-lenaP ,erutcurtS
NS-DS2069-CA-en
1-2 mm (GAP)
FULLY THREADED SCREW@ 300 O.C. U.N.O.,
STAGGERED
nordic .ca 1.33
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Half-Lap Joint NS-DS2031-CA-enDRAWING
==
68PARTIALLY THREADED SCREW
@ 300 O.C. U.N.O.
Structure, Panel-Panel -
nordic .ca 1.34
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Corner Joint with 90° Screws
-llaW-llaW ,erutcurtS
NS-DS2032-CA-enDRAWING
NORDIC X-LAM WALLS
PARTIALLY THREADED SCREW @ 300 O.C. U.N.O.
nordic .ca 1.35
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Notched Corner Joint with 90° Screws
-llaW-llaW ,erutcurtS
NS-DS2033-CA-enDRAWING
15
NORDIC X-LAM WALLS
PARTIALLY THREADED SCREW @ 300 O.C. U.N.O.
nordic .ca 1.36
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Corner Joint with 45° Screws
-llaW-llaW ,erutcurtS
NS-DS2034-CA-enDRAWING
NORDIC X-LAM WALLS
PARTIALLY THREADED SCREW@ 300 O.C. U.N.O.
nordic .ca 1.37
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
= =
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
T-Joint with 90° Screws
-llaW-llaW ,erutcurtS
NS-DS2035-CA-enDRAWING
NORDIC X-LAM WALLS
PARTIALLY THREADED SCREW @ 300 O.C. U.N.O.
nordic .ca 1.38
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°45°
2020-02-01
TITLE
CATEGORY
T-Joint with 45° Screws
Structure, Wall-WallDATE EGAPELACS
-
NS-DS2036-CA-enDRAWING
NORDIC X-LAM WALLS
PARTIALLY THREADED SCREWS@ 300 O.C. U.N.O., STAGGERED
nordic .ca 1.39
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Base Plate with Steel Square
-etalP esaB ,erutcurtS
NS-DS2037-CA-enDRAWING
THREADED ROD
STEEL SQUARE
NON-SHRINKGROUT 25 mm
PROVIDE CHAMFER IN WOOD TO CLEAR
STEEL WELDS
CONCRETE
NORDIC LAM COLUMN
MECHANICAL ANCHOR
nordic .ca 1.40
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
1-2 mm (GAP)
10 m
m (G
AP
)
TITLE
CATEGORY DATE EGAPELACS
Base Plate with Knife Plate and Four Mechanical Anchors
-etalP esaB ,erutcurtS
NS-DS2038-CA-enDRAWING
STEEL DOWEL
STEEL KNIFE PLATE
PROVIDE CHAMFER IN WOOD TO CLEAR
STEEL WELDS
NON-SHRINKGROUT 25 mm
MECHANICAL ANCHOR
NORDIC LAM COLUMN
CONCRETE
nordic .ca 1.41
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
1-2 mm (GAP)
10 m
m (G
AP
)
TITLE
CATEGORY DATE EGAPELACS
Base Plate with Knife Plate and Four Hidden Mechanical Anchors
-etalP esaB ,erutcurtS
NS-DS2039-CA-enDRAWING
NON-SHRINK GROUT 25 mm
MECHANICAL ANCHOR
PROVIDE CHAMFER IN WOOD TO CLEAR
STEEL WELDS
STEEL DOWEL
STEEL KNIFE PLATE
CONCRETE
NORDIC LAM COLUMN
nordic .ca 1.42
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
10 m
m (G
AP)
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Two-storey Base Plate with Knife Plate
-etalP esaB ,erutcurtS
NS-DS2040-CA-enDRAWING
2 STOREY BASE PLATEWITH KNIFE PLATE
NON-SHRINK GROUT 25 mm
MECHANICAL ANCHOR
PROVIDE CHAMFER IN WOOD TO CLEAR
STEEL WELDS
STEEL DOWEL
CONCRETE
NORDIC LAM COLUMN
nordic .ca 1.43
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
1-2 mm EACH SIDE (GAP)
40 m
m (G
AP
)
TITLE
CATEGORY DATE EGAPELACS
Two-storey Base Plate with Glued-in Rod
-etalP esaB ,erutcurtS
NS-DS2041-CA-enDRAWING
GLUED-IN ROD
2 STOREY BASE PLATE
NON-SHRINK GROUT 25 mm
NORDIC LAM COLUMN
MECHANICAL ANCHOR
CONCRETE
nordic .ca 1.44
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
1-2 mm EACH SIDE (GAP)
40 m
m (G
AP
)
TITLE
CATEGORY DATE EGAPELACS
Two-storey Base Plate with Glued-in Rod and Pocket
-etalP esaB ,erutcurtS
NS-DS2042-CA-enDRAWING
NORDIC LAM COLUMN
2 STOREY BASE PLATE
FILL IN CONCRETE
MECHANICAL ANCHOR
GLUED-IN ROD
NON-SHRINK GROUT 25 mmCONCRETE
nordic .ca 1.45
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
DRAWING
1-2 mm EACH SIDE (GAP)
40 m
m (G
AP
)
Two-storey Base Plate with Glued-in Rod and Half-height Pocket
-etalP esaB ,erutcurtS
NS-DS2070-CA-en
NORDIC LAM COLUMN
2 STOREY BASE PLATE
FILL IN CONCRETE
MECHANICAL ANCHOR
GLUED-IN ROD
NON-SHRINK GROUT 25 mmCONCRETE
nordic .ca 1.46
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
45°
45°45°
45°
45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Double Member Beam with Spacing
-nmuloC-maeB ,erutcurtS
NS-DS2043-CA-enDRAWING
NORDIC LAM COLUMN
NORDIC LAMBEAM
PROVIDE NECESSARY SPACING FOR PLUMBING
FULLY THREADEDSCREW
nordic .ca 1.47
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
0.5-1.0 mm (GAP)0.5-1.0 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Double Member Beam Without Spacing
-nmuloC-maeB ,erutcurtS
NS-DS2044-CA-enDRAWING
THREADED ROD
NORDIC LAMCOLUMN
NORDIC LAMBEAM
PARTIALLY THREADED SCREWS @ 300 O.C. U.N.O., STAGGERED
nordic .ca 1.48
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Knife Plate with Shear Key
-nmuloC-maeB ,erutcurtS
NS-DS2045-CA-enDRAWING
2-4
mm
(GA
P)
10
10
10
NORDIC LAM BEAM
STEEL DOWEL
STEEL KNIFE PLATE
1-2 mm (GAP)
PROVIDE SPACING FOR SCREW HEAD
SHEAR KEY
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
NORDIC LAM COLUMN
PARTIALLY THREADED SCREWS
nordic .ca 1.49
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Knife Plate with Shear Key and Bearing Plate
-nmuloC-maeB ,erutcurtS
NS-DS2046-CA-enDRAWING
2-4
mm
(GA
P)
10 10
10
10
NORDIC LAM COLUMN
NORDIC LAM BEAM
STEEL DOWEL
STEEL KNIFE PLATE WITH BEARING PLATE
PROVIDE CHAMFER IN WOOD TO CLEAR STEEL WELDS
1-2 mm (GAP)
SHEAR KEY
PROVIDE SPACING FOR SCREW HEAD
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
PARTIALLY THREADED SCREWS
nordic .ca 1.50
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
0.5-1.0 mm (GAP) 0.5-1.0 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Single Beam, Bridle Joint
-nmuloC-maeB ,erutcurtS
NS-DS2047-CA-enDRAWING
NORDIC LAM COLUMN
NORDIC LAM BEAM
PARTIALLY THREADED SCREW
nordic .ca 1.51
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
0.5-1.0 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Continuous Beam, Bridle Joint
-nmuloC-maeB ,erutcurtS
NS-DS2048-CA-enDRAWING
0.5-1.0 mm (GAP)
NORDIC LAM BEAM
NORDIC LAM COLUMN
PARTIALLY THREADED SCREW
nordic .ca 1.52
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Half-Lap Joint
-nmuloC-maeB ,erutcurtS
NS-DS2049-CA-enDRAWING
NORDIC LAM BEAM
NORDIC LAM COLUMN
PARTIALLY THREADED SCREW
nordic .ca 1.53
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
==
==
==
==
==
==
==
2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Face-mount Hanger
-nmuloC-maeB ,erutcurtS
NS-DS2050-CA-enDRAWING
RING SHANK NAIL
NORDIC LAM BEAM
HANGER
NORDIC LAM COLUMN
1-2 mm (GAP)
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
nordic .ca 1.54
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
==
==
==
==
==
==
==
2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Face-mount Hanger with Concealed Flanges
-nmuloC-maeB ,erutcurtS
NS-DS2051-CA-enDRAWING
1-2 mm (GAP)
RING SHANK NAIL
HANGER
NORDIC LAM COLUMN
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
NORDIC LAM BEAM
nordic .ca 1.55
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
=
45°
2020-02-01
(a)
TITLE
CATEGORY DATE EGAPELACS
Beam on Cleat
-nmuloC-maeB ,erutcurtS
NS-DS2053-CA-enDRAWING
5 m
m (G
AP
)
NORDIC LAM COLUMN
NORDIC LAM CLEAT
NORDIC LAM BEAM
1-2 mm (GAP)
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
FULLY THREADED SCREW
PARTIALLY THREADED SCREW
PARTIALLY THREADED SCREW
nordic .ca 1.56
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Knife Plate
-nmuloC-triG ,erutcurtS
NS-DS2055-CA-enDRAWING
PROVIDE SPACING FOR SCREW HEAD
NORDIC LAMGIRT
NORDIC LAM COLUMN
STEEL KNIFE PLATE
STEEL DOWEL
PARTIALLY THREADEDSCREW
nordic .ca 1.57
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
(a) (a)1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Steel Plates
-nmuloC-triG ,erutcurtS
NS-DS2056-CA-enDRAWING
1-2 mm (GAP)
NORDIC LAMGIRT
STEEL PLATE
RING SHANK NAIL
NORDIC LAM COLUMN
a) The 1-2 mm gap may not be required depending on the detail on the other side of the beam.
nordic .ca 1.58
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°
45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
45° Screws
-nmuloC-triG ,erutcurtS
NS-DS2057-CA-enDRAWING
NORDIC LAMGIRT
NORDIC LAM COLUMN
FULLY THREADED SCREW
nordic .ca 1.59
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
=
2020-02-01
1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Nailed Face-mount Hanger
-maeB-tsioJ ,erutcurtS
NS-DS2058-CA-enDRAWING
RING SHANK NAIL
HANGER
NORDIC LAM BEAM
NORDIC LAM JOIST
nordic .ca 1.60
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
==
==
=
2020-02-01
5 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Nailed Face-mount Hanger with Concealed Flanges
-maeB-tsioJ ,erutcurtS
NS-DS2059-CA-enDRAWING
RING SHANK NAIL
HANGER
NORDIC LAM BEAM
NORDIC LAM JOIST
nordic .ca 1.61
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
==
2020-02-01
1-2 mm (GAP)1-2 mm (GAP)
TITLE
CATEGORY DATE EGAPELACS
Bolted Face-mount Hanger
-maeB-tsioJ ,erutcurtS
NS-DS2060-CA-enDRAWING
THREADED ROD
RING SHANK NAIL
HANGER
NORDIC LAM BEAM
NORDIC LAM JOIST
nordic .ca 1.62
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Knife Plate with Saddle
-maeB-tsioJ ,erutcurtS
NS-DS2061-CA-enDRAWING
1-2 mm (GAP)
STEEL KNIFE PLATE
STEEL DOWEL
PROVIDE SPACING FOR SCREW HEAD
STEEL SADDLE
NORDIC LAM BEAM
NORDIC LAM JOIST
PARTIALLY THREADED SCREWS
nordic .ca 1.63
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Knife Plate
-maeB-tsioJ ,erutcurtS
NS-DS2062-CA-enDRAWING
1-2 mm (GAP)
STEEL KNIFE PLATE
STEEL DOWEL
NORDIC LAM BEAM
NORDIC LAM JOIST
PROVIDE SPACING FOR SCREW HEAD
PARTIALLY THREADED SCREWS
nordic .ca 1.64
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°45°
45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
45° Screws - Option 1
-maeB-tsioJ ,erutcurtS
NS-DS2063-CA-enDRAWING
NORDIC LAM BEAM
NORDIC LAM JOIST
FULLY THREADED SCREWS
nordic .ca 1.65
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°45°
0.7
x h
(MIN
.)
h
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
45° Screws - Option 2
-maeB-tsioJ ,erutcurtS
NS-DS2064-CA-enDRAWING
NORDIC LAM BEAM
NORDIC LAM JOIST
FULLY THREADED SCREW
nordic .ca 1.66
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M
45°45°
2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Joist on Beam with 45° Screws and Glued-In Rod
-maeB-tsioJ ,erutcurtS
NS-DS2065-CA-enDRAWING
NORDIC LAM BEAM
NORDIC LAM JOIST
THREADED ROD
PARTIALLY THREADED SCREW
nordic .ca 1.67
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Decking to Steel Beam
-dirbyH ,erutcurtS
NS-DS2066-CA-enDRAWING
NORDIC LAM DECKING
NORDIC LAM SILL
GALVANIZED COMMON NAIL
STEEL CONNECTOR
SECONDARY STEEL BEAM
STEEL BEAM
Note:1. For assembly details refer to technical note D-R00.
RING SHANK NAIL
GALVANIZED SPIRAL NAIL
VERSION2020-08-13
2
DE TA IL SNOR DIC L A M+ NOR DIC X-L A M
NS-DS2ENGLISH
MECHANICAL, ELECTRICAL, AND PLUMBING
nordic .ca 2.1
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Vertical, Double-Member Beam
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2501-CA-en
PROVIDE NECESSARY SPACING FOR PLUMBING
METAL STUDS AND INSULATION
NORDIC X-LAMSLAB
OPENING, CUT ON SITE( BY OTHERS)
PIPE
NORDIC LAM BEAM
GYPSUM BOARD
NORDIC LAM COLUMN
nordic .ca 2.2
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Horizontal, Pre-Machined Opening
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2502-CA-en
PRE-MACHINED OPENING
NORDIC X-LAM LINTEL
NORDIC X-LAM WALL
nordic .ca 2.3
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Horizontal, Electrical Box with 38 mm x 64 mm Wood Studs
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2503-CA-en
38 mm x 64 mm WOOD STUDS AND INSULATION
ELECTRICAL BOX
NORDIC X-LAM WALL
GYPSUM BOARD
SILL PLATE
NORDIC X-LAM SLAB
nordic .ca 2.4
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Horizontal, Raised Floor
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2504-CA-en
NORDIC X-LAM SLAB
NORDIC X-LAM WALL
GYPSUM BOARD
RESILIENT CHANNEL
PLYWOOD
PIPE
JOIST
INSULATION
nordic .ca 2.5
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Horizontal, Suspended Ceiling
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2505-CA-en
METAL FURRING
METAL STUDS AND INSULATION
GYPSUM BOARDS
NORDIC X-LAMSLAB
MECHANICAL DUCTPIPE OR DUCT
NONCOMBUSTIBLE INSULATION
nordic .ca 2.6
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Horizontal, Joist on Beam
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2506-CA-en
NORDIC LAM DECKING
NORDIC LAM JOIST
NORDIC LAM COLUMN
PIPE
NORDIC LAM BEAM
nordic .ca 2.7
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
TITLE
CATEGORY DATE EGAPELACS
Horizontal, Bevelled Beam
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2507-CA-en
NORDIC X-LAM SLAB
NORDIC LAM COLUMN
PIPE
NORDIC LAM BEAM
nordic .ca 2.8
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
UAO OAI
SAH
HRV
DRY
RA
SA
SA
TITLE
CATEGORY DATE EGAPELACS
Multi-Residential Unit Diagram, Option 1
gnibmulP dna ,lacirtcelE ,lacinahceM -
DRAWING
NS-DS2508-CA-en
LegendSA Supply AirH HoodOAI Outdoor Air IntakeRA Return AirUAO Used Air OutletSEC DryerHRV Heat Recovery Ventilator
nordic .ca 2.9
NS-DS2 D E TA I L S
N O R D I C L A M + N O R D I C X- L A M 2020-02-01
SA
SA
H
RA
HRV
UAO OAI
DRY
SA
DATE EGAPELACS
Multi-Residential Unit Diagram, Option 2
gnibmulP dna ,lacirtcelE ,lacinahceM -
TITLE
CATEGORY
DRAWING
NS-DS2509-CA-en
LegendSA Supply AirH HoodOAI Outdoor Air IntakeRA Return AirUAO Used Air OutletSEC DryerHRV Heat Recovery Ventilator
nordic .ca
![[Nordic Built Challenge 17.12.2013] Trine Pertou Mach, Nordic Built: Nordic Built](https://static.documents.pub/doc/80x56/547174dcb4af9f980a8b4ad9/nordic-built-challenge-17122013-trine-pertou-mach-nordic-built-nordic-built.jpg)