High Resolution WDR - Color Camerawith 22x Optical and 10x Digital - Zoom Lens
Thank you for choosing our high qual i ty camera.Be fo re a t tempt ing to connec t o r opera te , p lease read and fol low these instruct ions.
M148-ZAK220-001
220X AUTO FOCUSZOOM COLOR CAMERAOperation Manual
Cautions
3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;
1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.
Note -This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.” WARNING -This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Caution -Any changes or modifications in construction of this devies which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
1. A regulated DC12V 500mA power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera.When unregulated power supply is applied, product warranty will beout of subject.2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level. If your monitor is switched to high impedance then please adjust accordingly.3. Do not attempt to disassemble the camera to gain access to the internal componets. Refer servicing to your dealer.4. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the CCD.5. Do not remove the serial sticker for the warranty service.
Cautions
4
Correct Disposal of This Product(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.Household users should contact either the retailer where they for disposal.
CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER. SERVICING TO QUALIFED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instruction in the literature accompanying the appliance.
Cautions ··························································· 31 General··························································· 6
1.1 Product Overview·········································· 61.2 Features····················································· 61.3 Specifications··············································· 61.4 Dimensions·················································· 71.5 Back panel controls and connectors····················· 8
2 Installation························································ 92.1 Power························································ 92.2 Video························································· 92.3 Remote Control············································ 10
2.3.1 RS-485················································ 102.3.2 DC-Lens control······································ 112.3.3 Day- / Night switching······························· 11
3 Camera setup··················································· 123.1 Zoom························································ 123.2 Focus······················································· 123.3 OSD setup menu·········································· 13
3.3.1 OSD display·········································· 133.3.2 Menu Structure······································· 143.3.3 Setup - Menu Operation····························· 16
3.3.3.1 FOCUS········································ 183.3.3.2 EXPOSURE·································· 183.3.3.3 White Balance································ 193.3.3.4 D-WDR/BLC·································· 203.3.3.5 DAY& NIGHT································· 223.3.3.6 IMAGE········································· 233.3.3.7 SPECIAL······································ 24
3.3.4 RESET················································ 26
Contents
5
1.1 PRODUCT OVERVIEWThe is a high resolution color camera equipped with a 22x auto-focus zoom lens and 10 x digital zoom.Many advanced features allow utilizing the in a wide range of CCTV - applications.
1.2 FEATURES• 22 x optical and 10 x digital zoom• 600 TVL horizontal resolution• 3DNR noise reduction• Enhanced sensitivity with 256 x DSS(Digital Slow Shutter)• Extended wide dynamic with D-WDR• HSBLC : Highlight Suppression BLC• 8 privacy zones• Day- / Night mode• Remote control by RS-485 and DC lens control
1.3 SPECIFICATIONSImage sensor 1/4” Sony Super HAD CCDⅡEffective pixel 752 x 582 (PAL), 768 x494(NTSC)Light sensitivity 0.2 Lux ( F = 1,6, AGC high, DSS off, 30 IRE)Lens 22x optical zoom 3.9 ~ 85.8 mmVideo output BNC socket, composite 1 Vs-s / 75 OhmVideo resolution 600 TV lines horizontalSignal/noise ratio > 50 dB (AGC off)Min. object distance 1 cm (wide) up to 1m (tele)Digital Slow Shutter auto, manual, off (2x to 256x)Remote control RS-485(Pelco-D/P), DC lens control(+/- 5VDC)
Back light compensation HSBLC on/off, BLC on/offCamera title max. 20 character, 16 colorsPower DC 12V +/- 10%, MAX. 210mAEnvironmental temp. -14°F~122°F(-10°C~+50°C)Humidity Less than 80%Dimensions (WxHxD) 66 x 64 x 111 mmWeight Approx. 400g
1 GENERAL
6
1.4 DIMENSIONS
1 GENERAL
7
110.8
64.0
66.0
38.2
32.0
1.5 BACK PANEL CONTROLS AND CONNECTORS
Arrow keys T / W Buttons for zoom control, in OSD menu row selection up/down
Arrow keys N / F Buttons for focus control, in OSD menu change of parameters
MENU key Open/close OSD setup menuVideo output BNC Video output BNC, composite 1 Vs-s / 75 Ohm
LED LED on indicates power on.Control inputs 485+ / 485-: Remote control input RS485
ZOOM/COM/FOCUS: input for zoom/focus control with +/- 5VDCD/N / GND: contact input for external day/night - switching
12V / GND Power input terminal for 12 VDC stabilized (+/- 10%)
1 GENERAL
8
485+
485-
ZOO
M
CO
M
FOC
US
D/N
GN
D
Arrow keysT / W / N / F
Video output BNC
12V / GND
Control inputs
LED
MENU key
2.1 POWER
Connect a stabilized 12 VDC power supply (500mA or higher) to the power terminal.
2.2 VIDEO
Connect the video output (BNC) with 75 Ohm video coax cable with DVR, monitor or other equipment with video input. Please take care for correct 75 Ohm termination.
2 INSTALLATION
9
INTERMEDIATE END MONITOR
VIDEO VIDEO
2.3 REMOTE CONTROLThe camera provides an input for RS-485 control with Pelco-D/P protocol.Further on the lens can be controlled by control devices with 5 VDC voltage (PTZ-receiver, control keyboards with DC output).The day / Night mode can be switched by an external contact.
2.3.1 RS-485Connect the RS-485 input with twisted pair cable to the control device.For details of RS-485 wiring please consult the related chapters in user manuals of DVRs or control keyboards.The RS-485 parameter (baud rate / address) need to be adjusted in the OSD menu SPECIAL.
Control commands for OSD - menu (Pelco-D/P protocol)(Go to) Preset 95 (or Preset 96) OSD setup menu open / close
Joystick/arrow keys up / down or zoom +/- switch between menu linesJoystick/arrow keys left / right or focus +/- change of values / parametersJoystick/arrow key right or focus + Enter
2 INSTALLATION
10
2.3.3 DC-Lens controlThe lens can be controlled by control devices with 5 VDC voltage (PTZ-receiver, control keyboards with DC output).Please check the control device to correct output voltage (+/- 5VDC max).
2.3.3 Day- / Night switchingThe day/night switching can be controlled by an external dry contact. Closing the contact (to GND) will turn the camera in night mode. In OSD menu DAY&NIGHT the item MODE needs to be set to EXTERNAL.
ATTENTION: This camera is equipped with a fixed IR-cut filter. For this reason the camera is not applicable for installation with IR illumination.
2 INSTALLATION
11
3.1 ZOOMThe key T is used for zoom in, W for zoom out.
3.2 FOCUSThe key N focuses the lens in near distance, F key focuses in far distance.
ATTENTION: The FOCUS keys are deactivated in the mode FOCUS: AUTO
3 CAMERA SETUP
12
Focus near Focus far
MENU
Zoom tele
Zoom wide
3.3 OSD SETUP MENU
3.3.1 OSD display
3 CAMERA SETUP
13
NO Function Format Description
①
Focus
Auto Focus
Interval AF
Zoom Trigger AF
Manual Focus
WB
ATW
AWB
Push Auto WB
Manual WB
Indoor WB
Outdoor WB
WDR WDR Off
WDR On
BLCBLC Off
BLC On
HSBLCHSBLC Off
HSBLC On
NightDay
Night
FreezeNormal
Freeze On
Filp
Normal
Horizontal Filp(Mirror)
Vertical Filp
HV(180˚) Fiilp
NO Function Format Description
② MotionNormal
Motion Detected
③ZoomRation
Optical Zoom
Digital Zoom
④ ID:000 ~ ID:255 Camera ID
⑤ LOADING... Standby message
⑥ TitleMax.20characters /Position Selectable
3.3.2 Menu Structure
3 CAMERA SETUP
14
SETUP
1. FOCUS ┛2. EXPOSURE ┛3. WHITE BAL ATW4. D-WDR/BLC OFF5. DAY&NIGHT AUTO6. IMAGE ┛7. SPECIAL ┛8. RESET OFF9. EXIT ┛
FOCUS
FOCUS MODE ZOOM TRIGZOOM START .|...... 1ZOOM STOP ….. | 220ZOOM SPEED FASTD-ZOOM ONMIN. DIST 50CMRETURN ┛
AF INTERVAL
RUN TIME ..| … 10INTERVAL ..| …… 60RETURN ┛
IRIS MANUAL
LEVEL ..|…….. 100RETURN ┛
AGC MANUAL
LEVEL |……. -3DBRETURN ┛
WB MANUAL
RED ....|…… 50BLUE .…|…… 50RETURN ┛
D-WDR
LEVEL ….|…… 9RETURN ┛
BLC
LEVEL MIDDLEAREA ┛ RETURN ┛
BLC AREAH. START 2V. START 2WIDTH 4 HEIGHT 4RETURN ┛
HSBLC AREAH. START 0V. START 3WIDTH 8HEIGHT 4RETURN ┛
HSBLCLEVEL ….. | ….. 4AREA ┛DISP. MODE ALL DAYRETURN ┛
EXPOSURE
SHUTTER OFFIRIS AUTOAGC AUTOMAX. AGC MIDDLEMAX. FIELD OFFBRIGHT …….. |…. 50RETURN ┛
WHITE BAL
D-WDR / BLC
3 CAMERA SETUP
15
DAY & NIGHT
IMAGE
SMART IR ┛3DNR ┛FREEZE OFFROTATE OFFSHARPNESS ..|… 15NEGATIVE OFFRETURN ┛
SPECIAL
CAM ID 001BAUDRATE 9600LANGUAGE ENGTITLE ┛PRIVACY ┛MOTION ┛OSD SET ┛ RETURN ┛
D&N AUTO
DETECT MODE VIDEO ┛DWELL TIME ..|…… 5BURST ONRETURN ┛
SMART IR
GAIN ….|.... 8AREA ┛RETURN ┛
3DNR
LEVEL ….. |…. 50RETURN ┛
PRIVACYMASK NO 1DISP MODE INT.LOCKAREA ┛COLOR C0TRANSPARENT OFFRETURN ┛
OSD SET
CAM ID OFFZOOM MAG OFFFUNC OSD OFFOSD COLOR C3RETURN ┛
MOTION
AREA NO 1DETECT MODE ONH. START ..|… 31V. START .|…. 18WIDTH …|… 53HEIGHT …|… 37SENSE …|… 10DISP. MODE OFFRETURN ┛
TITLE
------------------------ ABCDEFGHIJKLM (LEFT) NOPQRSTUVWXYZ (RIGHT) 0123456789► →← (SPACE) ↑↓ ( ) -■/=& : ~,. (BACK)
DISPLAY ONCLEAR OFFPOSITION ┛RETURN ┛
D&N VIDEO
D->N LEVEL ….|.... 176D<- N LEVEL ….|.... 76RETURN ┛
SMART IR AREA
H. START 3V. START 2WIDTH 2HEIGHT 3RETURN ┛
TITLE POSITION
CURRENT TITLE
RETURN ┛
NON. LOCK MASK
WIDTH . .|…. 10HEIGHT ..|…. 10PAN POSI ∙∙∙∙|∙∙∙∙ 0TILT POSI ∙∙∙∙|∙∙∙∙ 0ZOOM POSI ← W T →MASK RESET OFFRETURN 」
INT.LOCK MASK
WIDTH .|…… 10HEIGHT ..|…… 10ZOOM POSI ← W T →MASK RESET OFFRETURN 」
3 CAMERA SETUP3.3.3 Setup - Menu Operation
Press the key MENU for opening the OSD setup menu.The screen shows the main setup menu.
SETUP
1. FOCUS 」 2. EXPOSURE 」3. WHITE BAL ATW / AWB / PWB」/ MWB」 / IWB / OWB4. D-WDR/BLC OFF / D-WDR」 / BLC」 / HSBLC」5. DAY&NIGHT AUTO」 / COLOR / BW / EXTERNAL6. IMAGE 」7. SPECIAL 」8. RESET OFF / ON」9. EXIT 」
NEAR / FAR
TELE
/ W
IDE
The keys T / W move the cursor vertical between the rows, changing parameters and values is done by the FOCUS - keys N / F. The character 」indicates a sub-menu.The F key is used for confirming settings (ENTER) and for opening sub-menus.In sub-menus the line RETURN is used for exit and return to main menu.The OSD menu can be closed in any position by MENU key.
Attention: If MENU key is used for exit of a menu page, all changes in settings are cancelled.For saving the changes go to the last row and confirm with F (right) - key.
16
MENU
3 CAMERA SETUP3.3.3.1 FOCUS
FOCUS
FOCUS MODEZOOM STARTZOOM STOPZOOM SPEEDD-ZOOMMIN. DISTRETURN
AUTO/INTERVAL」/ZOOM TRIG/MANUAL...l... 1 ~ 22...l... 1 ~ 220SLOW / NORMAL / FAST / V.FASTOFF / ON1CM/10CM/50CM/1M/2M/3M/5M/10M/INF」
FOCUS MODE Focus operation modeAUTO Auto focus permanent on.INTERVAL The focus will be checked in intervals in the range 3~255 s
(setup in line INTERVAL) for a defined duration (3 ~255s, setup in line RUN TIME).
ZOOM TRIG The auto focus function is active at each change of zoom position. After focussing the auto focus function is switched off.
MANUAL Manual focus adjustment.ZOOM START Start position of zoom lens, adjustable 1~22ZOOM STOP End position of zoom lens, adjustable 1~220ZOOM SPEED Zoom speed, adjustable in 4 stepsD-ZOOM Digital zoom on / offMIN. DIST Minimum object distance, adjustable in range 1cm to
endless (INF)AF RUN TIME see FOCUS MODE: INTERVALINTERVAL see FOCUS MODE: INTERVAL
17
3 CAMERA SETUP3.3.3.2 EXPOSURE
EXPOSURE
SHUTTERIRISAGCMAX. AGCMAX. FIELDBRIGHTRETURN
256FLD / ... / 2FLD / AUTO / OFF / FLK / ... / 1 / 100000AUTO / MANUAL」AUTO / MANUAL」OFF / LOW / MIDDLE / HIGH / SUPEROFF / 2FLD / 4FLD / ... / 256FLD···l··· 1 ~ 100」
SHUTTER AUTO: Automatic shutterFLK: Flickerless mode1:160~1/100.000: Manual shutter speed2~256FLD: Fixed value for Digital Slow Shutter
IRIS AUTO: Automatic lens controlMANUAL: Manual lens control (setup in line IRIS LEVEL)
AGC AUTO: Automatic gain controlMANUAL: Manual gain control (setup in line AGC LEVEL)
IRIS LEVEL Adjustment of lens level in lens mode MANUALAGC LEVEL Gain adjustment in AGC mode MANUAL MAX AGC Max. gain value of AGC in AGC mode AUTOMAX FIELD Adjustment of max. value of DSS (Digital Slow Shutter)
2~256FLD (Field)BRIGHT Adjustment of image brightness
18
3.3.3.3 White Balance
WHITE BAL
MODE ATWPUSH -RED -BLUE -RETURN 」
MODE Operation mode of white balanceATW: Automatic White Balance in temperature range 2400°K to 12000°KAWB: Temperature range is broader than ATW.INDOOR: Preset setting for indoor applicationsOUTDOOR: Preset setting for outdoor applicationsPUSH: One-time, manual started white adjustment, start in line PUSHMANUAL: Manual white balance
PUSH ON: Start of white adjustment in mode PUSHRED In WB - mode "MANUAL" adjustment of RED - levelBLUE In WB - mode "MANUAL" adjustment of BLUE - level
3 CAMERA SETUP
19
3 CAMERA SETUP3.3.3.4 D-WDR/BLC
D-WDR / BLC
MODE D-WDRLEVEL ···l··· 9AREA -DISP. MODE -RETURN 」
Mode: D-WDR Digital Wide Dynamic Range for balancing strong light differences in scenery
Level Adjustment of WDR level
D-WDR / BLC
MODE BLCLEVEL MIDDLEAREA 」DISP. MODE -RETURN 」
BLC AREA
H. START 3V. START 2WIDTH 2HEIGHT 3RETURN 」
Mode: BLC Back Light Compensation, dark objects enclosed with backlight will be brightened.
Level Compensation level in 3 stepsArea Adjustment of area for BLC
H.START: Position of 1. field of area from left (0~7)V.START: Position of 1. field of area from top (0~7)WIDTH: horizontal size of the area in fields (0~8) HEIGHT: vertical size of the area in fields (0~8)
20
3 CAMERA SETUP
D-WDR / BLC
MODE HSBLCLEVEL ···l··· 4AREA 」DISP. MODE ALL DAYRETURN 」
Mode: HSBLC Highlight suppression, strong light sources (e.g. car lamps) will be blacked out in image
Level Sensitivity trigger level in 9 stepsArea Adjustment of monitored area for HSBLC in a grid 8x8
H.START: Position of 1. field of area from left (0~7)V.START: Position of 1. field of area from top (0~7)WIDTH: horizontal size of the area in fields (0~8) HEIGHT: vertical size of the area in fields (0~8)
DISP.MODE ALL DAY: HSBLC is always onNIGHT: HSBLC only active in night mode
21
3 CAMERA SETUP3.3.3.5 DAY& NIGHT
D&N AUTO
MODE AUTODETECT MODE VIDEO DWELL TIME ···l······ 5D>N LEVEL ······l··· 176D<N LEVEL ····l····· 76BURST ONRETURN 」
MODE AUTO: Automatic day/night switchingCOLOR: day / color modeBW: night / b/w modeEXTERNAL: Switching by external contact
DETECT MODE VIDEO: In mode AUTO the D/N switching is controlled by video signal levelSENSOR: not supported mode
DWELL TIME Delay time for switching 0~60 sD>N LEVEL Sensitivity trigger level for switching day to night, range
1~255D<N LEVEL Sensitivity trigger level for switching night to day, range
0~254BURST ON: color burst in video signal also in b/w mode
OFF: color burst in video signal in b/w mode off
ATTENTION: This camera is equipped with a fixed IR-cut filter. For this reason the camera is not applicable for installations with IR illumination.
22
3 CAMERA SETUP3.3.3.6 IMAGE
IMAGE
SMART IR 」3 DNR 」FREEZE OFFROTATE OFFSHARPNESS ······l··· 15NEGATIVE OFFRETURN 」
SMART IR Mode not supported3DNR Digital Noise Reduction
MODE: ON : Noise reduction deactivatedLEVEL: Level adjustment for noise reduction, range 0~100
FREEZE ON: Freeze of current imageROTATE ON: Image turn 180°SHARPNESS Adjustment of image sharpness, range 0~31NEGATIVE ON: Negation of image colors
23
24
3 CAMERA SETUP
24
3.3.3.7 SPECIAL
SPECIAL
CAM ID 001BAUDRATE 9600LANGUAGE ENGTITLE 」PRIVACY 」MOTION 」OSD SET 」RETURN 」
CAM ID RS-485 address of camera, range 0~255BAUDRATE Baud rate of RS-485 transmission, 2400, 4800, 9600, 19200
or 38400.
Control commands for OSD - menu (Pelco-D/P protocol).
(Go to) Preset 95 (or Preset 96) OSD setup menu open / close
Joystick / arrow keys up / down or zoom +/-
switch between menu lines
Joystick / arrow keys left / right or focus +/-
change of values / parameters
Joystick / arrow key right or focus +
Enter
LANGUAGE OSD menu language, EnglishTITLE Camera title with max. 20 characters.
Characters A~. : Select up to 20 characters for the title, confirm with MENU key.DISPLAY: ON: Displays the title.CLEAR: ON: Deletes the complete title.POSITION: Adjustment of title position on the screen by arrow keys.
TITLE
------------------------------ ABCDEFGHIJKLM (LEFT) NOPQRSTUVWXYZ (RIGHT) 0123456789► →← (SPACE) ↑↓ ( ) -■/=& : ~,. (BACK)
DISPLAY ONCLEAR OFFPOSITION ┛RETURN ┛
25
3 CAMERA SETUPPRIVACY Privacy zone adjustment, up to 8 areas can be masked.
PRIVACY
MASK NO 1DISP MODE INT.LOCKAREA 」COLOR C0TRANSPARENT OFFRETURN 」
MASK NO: Selection privacy zone 1~8 for setup.DISP MODE: OFF: Privacy zone not active. NON.LOCK / INT.LOCK: Privacy zone active.AREA: WIDTH: Width of privacy zone. HEIGHT: Height of privacy zone. PAN POSI: Position horizontal. TILT POSI: Position vertical. ZOOM POSI: Setup zoom position / test. MASK RESET: Removing of mask.
MOTION Motion detection with up to 4 zones
MOTION
AREA NO 1 ~ 4DETECT MODE OFF / ONH. START ··l··· 0 ~ 200V. START ··l··· 0 ~ 140WIDTH ··l··· 0 ~ 200HEIGHT ··l··· 0 ~ 140SENSE ··l··· 0 ~ 40DISP. MODE OFF/OSD/AREA /OSD +AREARETURN 」
MODE: ON: Motion detection on (zone1~4).AREA NO: Selection zone 1~4 for setup.DETECT MODE: ON: Detection active for selected zone.H.START: Left border of zone.V.START: Top border of zone.WIDTH: Width of zone.HEIGHT: Height of zone.SENSE: Sensitivity of detection.DISP.MODE: OSD: In case of detection the symbol is shown on screen. AREA: In case of detection the area is shown transparent on screen. OSD+AREA: In case of detection the symbol and area are shown on screen.
25
26
3 CAMERA SETUPOSD SET Display options
OSD SET
CAM ID OFFZOOM MAG OFFFUNC OSD OFFOSD COLOR C3RETURN 」
CAM ID: The RS-485 address will be displayed.ZOOM MAG: In case of lens operation the zoom position appears for 5 s.FUNC OSD: In case of lens operation the status icons appear for 5 s.OSD COLOR: Color setup for OSD menu.
3.3.4 RESET
All settings of the camera will be initialized and set to factory defaults.
26