Chapter 1 Overview of Administrator Guide 1-1.................................................
1.1 Objective 1-1................................................................................................1.2 Requirements for Administrator 1-1..............................................................1.3 Organization of This Guide 1-2.....................................................................
1.3.1 Administrative Tasks 1-2......................................................................1.3.2 Maintenance Items 1-2.........................................................................1.3.3 Commands and Tools 1-2....................................................................1.3.4 FAQ 1-3................................................................................................
Chapter 2 Server Parameter Settings 2-1............................................................
2.1 Overview of Server Parameter Settings 2-1.................................................2.2 Modifying Server Time 2-1...........................................................................
2.2.1 Operation Effect 2-1.............................................................................2.2.2 Operation Procedure 2-1......................................................................
2.3 Modifying Host name of Server 2-2..............................................................2.3.1 Operation Effect 2-2.............................................................................2.3.2 Operation Procedure 2-2......................................................................
2.4 Modifying Server IP Address 2-3..................................................................2.4.1 Operation Effect 2-3.............................................................................2.4.2 Operation Procedure 2-3......................................................................
2.5 Setting Parameters of Server with Multiple IPs 2-4......................................2.5.1 Operation Effect 2-4.............................................................................2.5.2 Operation Procedure 2-5......................................................................
Chapter 3 User Management 3-1..........................................................................
3.1 Overview of User Management 3-1..............................................................3.2 Introduction to User Account 3-1..................................................................
3.2.1 Types of User Account 3-1...................................................................3.2.2 Operating System User Accounts and the Authority 3-1......................3.2.3 Database User Account and the Authority 3-3.....................................3.2.4 M2000 User Accounts and the Authority 3-3.......................................
3.3 Creating Operating System User 3-3...........................................................3.3.1 Operation Effect 3-3.............................................................................3.3.2 Operation Procedure 3-3......................................................................
3.4 Modifying Password of Operating System User 3-4.....................................3.4.1 Operation Effect 3-4.............................................................................3.4.2 Modifying Password of root 3-4............................................................3.4.3 Modifying Password of dbuser 3-4.......................................................3.4.4 Modifying Password of omcuser 3-4....................................................3.4.5 Modifying Password of ftpuser 3-4.......................................................
3.5 Modifying Password of Database User 3-5..................................................
3.5.1 Operation Effect 3-5.............................................................................3.5.2 Operation Procedure 3-5......................................................................
3.6 Creating M2000 User Group 3-6..................................................................3.6.1 Operation Effect 3-6.............................................................................3.6.2 Operation Procedure 3-6......................................................................
3.7 Creating M2000 User Account 3-6...............................................................3.7.1 Operation Effect 3-6.............................................................................3.7.2 Operation Procedure 3-6......................................................................
3.8 Monitoring M2000 Users 3-6........................................................................3.8.1 Operation Effect 3-6.............................................................................3.8.2 Operation Procedure 3-7......................................................................
Chapter 4 Log Management 4-1............................................................................
4.1 Overview of Log Management 4-1...............................................................4.2 Introduction to Log 4-1..................................................................................
4.2.1 Types of Logs 4-1................................................................................4.2.2 User Log 4-1........................................................................................4.2.3 NE Log 4-1...........................................................................................4.2.4 System Log 4-2....................................................................................4.2.5 Trace log 4-2........................................................................................
4.3 Browsing User Log 4-3.................................................................................4.3.1 Operation Effect 4-3.............................................................................4.3.2 Operation Procedure 4-3......................................................................
4.4 Browsing System Log 4-3.............................................................................4.4.1 Operation Effect 4-3.............................................................................4.4.2 Operation Procedure 4-3......................................................................
4.5 Checking Solaris Error Log 4-3....................................................................4.5.1 Operation Effect 4-3.............................................................................4.5.2 Operation Procedure 4-3......................................................................
Chapter 5 Server Performance Monitor 5-1.........................................................
5.1 Overview of Server Performance Monitor 5-1..............................................5.2 Querying Server Status through Client 5-1...................................................
5.2.1 Function 5-1.........................................................................................5.2.2 Operation Procedure 5-1......................................................................
5.3 Setting the Threshold of Server Status Alarm 5-2........................................5.3.1 Function 5-2.........................................................................................5.3.2 Operation Procedure 5-2......................................................................
5.4 Querying System Performance 5-2..............................................................5.4.1 Operation Effect 5-2.............................................................................5.4.2 Operation Procedure 5-3......................................................................
5.5 Adjusting System Performance 5-3..............................................................5.5.1 Operation Effect 5-3.............................................................................5.5.2 Operation Procedure 5-4......................................................................
Chapter 6 M2000 Process and Service Management 6-1...................................
6.1 Overview of M2000 Process and Service Management 6-1........................6.2 Introduction to M2000 Processes and Services 6-1.....................................
6.2.1 Overview to Processes and Services 6-1............................................6.2.2 SystemConfigurator 6-1.......................................................................6.2.3 sac_agent 6-1......................................................................................6.2.4 em_agent 6-2.......................................................................................6.2.5 monitor_agent 6-2................................................................................6.2.6 partition_agent 6-3...............................................................................6.2.7 audit_agent 6-3....................................................................................6.2.8 mo_agent 6-3.......................................................................................6.2.9 sm_agent 6-4.......................................................................................6.2.10 med_agent 6-4...................................................................................6.2.11 ts_agent 6-4.......................................................................................6.2.12 ifms_agent 6-4...................................................................................6.2.13 manager_agent 6-4............................................................................6.2.14 pm_agent 6-5.....................................................................................6.2.15 cmserver_agent 6-5...........................................................................6.2.16 swm_agent 6-5...................................................................................6.2.17 fmnotify_agent 6-5.............................................................................6.2.18 proxy_agent 6-6.................................................................................6.2.19 notify_agent 6-6.................................................................................
6.3 Querying Number of M2000 Processes 6-6.................................................6.3.1 Operation Effect 6-6.............................................................................6.3.2 Operation Procedure 6-6......................................................................
6.4 Querying Service Status 6-6.........................................................................6.4.1 Operation Effect 6-6.............................................................................6.4.2 Operation Procedure 6-6......................................................................
6.5 Starting M2000 Services 6-8........................................................................6.5.1 Operation Effect 6-8.............................................................................6.5.2 Operation Procedure 6-8......................................................................
6.6 Stopping M2000 Services 6-9......................................................................6.6.1 Operation Effect 6-9.............................................................................6.6.2 Operation Procedure 6-9......................................................................
Chapter 7 Database Management 7-1..................................................................
7.1 Overview of Database Management 7-1......................................................
7.2 Introduction to Database 7-1........................................................................7.2.1 Overview of Database 7-1....................................................................7.2.2 omcdb 7-1............................................................................................7.2.3 fmdb 7-2...............................................................................................7.2.4 pmdb 7-2..............................................................................................7.2.5 sysmdb 7-3...........................................................................................
7.3 Querying Database Status 7-4.....................................................................7.3.1 Operation Effect 7-4.............................................................................7.3.2 Operation Procedure 7-4......................................................................
7.4 Manually Displacing Alarm Data 7-5............................................................7.4.1 Operation Effect 7-5.............................................................................7.4.2 Operation Procedure 7-5......................................................................
7.5 Manually Displacing User Log 7-5................................................................7.5.1 Operation Effect 7-5.............................................................................7.5.2 Operation Procedure 7-6......................................................................
7.6 Setting Auto Displacing for Alarm Data 7-6..................................................7.6.1 Operation Effect 7-6.............................................................................7.6.2 Operation Procedure 7-6......................................................................
7.7 Setting Auto Displacing for User Log 7-7.....................................................7.7.1 Operation Effect 7-7.............................................................................7.7.2 Operation Procedure 7-7......................................................................
7.8 Deleting Performance Task 7-7....................................................................7.8.1 Operation Effect 7-7.............................................................................7.8.2 Operation Procedure 7-7......................................................................
7.9 Clearing Database 7-8..................................................................................7.9.1 Operation Effect 7-8.............................................................................7.9.2 Operation Procedure 7-8......................................................................
Chapter 8 Disk Space Management 8-1...............................................................
8.1 Overview of Disk Space Management 8-1...................................................8.2 Introduction to File System 8-1.....................................................................
8.2.1 Overview of System Structure 8-1.......................................................8.2.2 Server File System 8-1.........................................................................8.2.3 Client File System 8-2..........................................................................
8.3 Query Disk Space 8-2..................................................................................8.3.1 Operation Effect 8-2.............................................................................8.3.2 Operation Procedure 8-3......................................................................
8.4 Clearing Disk Space 8-3...............................................................................8.4.1 Operation Effect 8-3.............................................................................8.4.2 Operation Procedure 8-3......................................................................
Chapter 9 Dual-Plane Configuration 9-1..............................................................
9.1 Overview of Dual-Plane Configuration 9-1...................................................9.2 Introduction to Dual-Plane 9-1......................................................................9.3 Configuration Procedure of Dual-Plane 9-2..................................................9.4 Planning IP Data 9-2....................................................................................9.5 Manually Setting Dual-Plane 9-2..................................................................
9.5.1 Operation Effect 9-2.............................................................................9.5.2 Operation Procedure 9-2......................................................................
9.6 Automatically Setting Dual-Plane 9-3...........................................................9.6.1 Operation Effect 9-3.............................................................................9.6.2 Operation Procedure 9-3......................................................................
9.7 Verifying Dual-Plane Settings 9-4.................................................................9.7.1 Operation Effect 9-4.............................................................................9.7.2 Operation Procedure 9-4......................................................................9.7.3 Abnormal Handling 9-4........................................................................
Chapter 10 NTP Service Configuration 10-1..........................................................
10.1 Overview of NTP Service Configuration 10-1...............................................10.2 Introduction to NTP Service 10-1.................................................................10.3 Setting M2000 as Top NTP Server 10-2......................................................10.4 Setting M2000 as Middle NTP Server 10-2..................................................10.5 Setting M2000 as NTP Client 10-2...............................................................10.6 Starting NTP Service 10-2............................................................................10.7 Checking Running Status of NTP Service 10-3............................................10.8 Stopping NTP Service 10-3..........................................................................
Chapter 11 Backup and Restoration 11-1..............................................................
11.1 Overview of Backup and Restoration 11-1...................................................11.2 Introduction to Backup and Restoration 11-1...............................................
11.2.1 M2000 System Backup Contents 11-1.................................................11.2.2 M2000 System Backup and NE Data Backup 11-1.............................11.2.3 The Mode of M2000 System Backup and Restore 11-2......................11.2.4 Name of Backup Files 11-2..................................................................11.2.5 Storage Media of Backup File 11-2......................................................
11.3 Function Setting 11-3...................................................................................11.3.1 Introduction to Configuration File 11-3.................................................11.3.2 Setting Tape Drive Path 11-3...............................................................11.3.3 Setting Backup Media 11-3..................................................................
11.4 Automatically Backing Up M2000 System 11-4............................................11.4.1 Introduction to Auto Backup 11-4.........................................................11.4.2 Setting Auto Backup Time 11-5...........................................................
11.5 Manually Backing Up M2000 System 11-5...................................................11.5.1 Introduction to Manual Backup 11-5....................................................11.5.2 Carrying Out Manual Backup on Client 11-5........................................11.5.3 Carrying Out Manual Backup on Server 11-6......................................
11.6 Restoring M2000 System 11-6.....................................................................11.6.1 Function Introduction 11-6...................................................................11.6.2 Operation Procedure 11-6....................................................................
11.7 Backing Up Operating System 11-7.............................................................11.7.1 Function Introduction 11-7...................................................................11.7.2 Operation Procedure 11-7....................................................................
11.8 Restoring Operating System 11-9................................................................11.8.1 Function Introduction 11-9...................................................................11.8.2 Operation Procedure 11-9....................................................................11.8.3 Restoring Tape Information 11-9.........................................................11.8.4 Setting Up Equipment Tree and Boot Block 11-10................................11.8.5 Modifying System File and File System Information 11-11....................11.8.6 Restarting System 11-12........................................................................11.8.7 Encapsulating Disk Using Volume Manager 11-12................................
Chapter 12 Routine Maintenance 12-1...................................................................
12.1 Overview of Routine Maintenance 12-1.......................................................12.2 Daily Maintenance 12-1................................................................................
12.2.1 Daily Maintenance Item List 12-1.........................................................12.2.2 Checking Alarm Information 12-1.........................................................12.2.3 Checking Log Information 12-2............................................................12.2.4 Checking Solaris Error Log 12-2..........................................................12.2.5 Checking Database Status 12-2..........................................................12.2.6 Checking Hard Disk Space 12-2..........................................................12.2.7 Checking CPU Utilization 12-2.............................................................12.2.8 Checking Number of Processes 12-2..................................................12.2.9 Checking Service Status 12-3..............................................................
12.3 Weekly Maintenance 12-3............................................................................12.3.1 Weekly Maintenance Item List 12-3.....................................................12.3.2 Backing Up M2000 System 12-3..........................................................12.3.3 Checking M2000 Server Time 12-3.....................................................12.3.4 Finding core Files 12-4.........................................................................12.3.5 Clearing Useless Files 12-4.................................................................
12.4 Monthly Maintenance 12-4...........................................................................12.4.1 Monthly Maintenance Item List 12-4....................................................12.4.2 Checking Power Supply 12-4...............................................................12.4.3 Checking Server Hardware 12-4..........................................................
12.4.4 Checking Auxiliary Devices of Server 12-4..........................................
Chapter 13 Troubleshooting 13-1...........................................................................
13.1 Overview of Troubleshooting 13-1................................................................13.2 Troubleshooting Procedure 13-1..................................................................
13.2.1 Overview of Troubleshooting Procedure 13-1......................................13.2.2 Information Collection 13-1..................................................................13.2.3 Fault Location 13-1..............................................................................13.2.4 Fault Clearance 13-2............................................................................
13.3 Auto Shutdown of Operating System 13-2...................................................13.3.1 Symptom 13-2......................................................................................13.3.2 Fault Analysis 13-2...............................................................................13.3.3 Fault Clearance 13-3............................................................................
13.4 Abnormal Service Restart 13-3....................................................................13.4.1 Symptom 13-3......................................................................................13.4.2 Fault Analysis 13-3...............................................................................13.4.3 Fault Clearance 13-3............................................................................
13.5 Abnormal Service Termination 13-4.............................................................13.5.1 Symptom 13-4......................................................................................13.5.2 Fault Analysis 13-4...............................................................................13.5.3 Fault Clearance 13-4............................................................................
13.6 M2000 Services Starting or Stopping Failure 13-5.......................................13.6.1 Symptom 13-5......................................................................................13.6.2 Fault Analysis 13-5...............................................................................13.6.3 Fault Clearance 13-5............................................................................
Chapter 14 Emergency Maintenance 14-1.............................................................
14.1 Overview of Emergency Maintenance 14-1..................................................14.2 Emergency Maintenance for M2000 Server 14-1.........................................
14.2.1 Function Introduction 14-1...................................................................14.2.2 Operation Procedure 14-1....................................................................
14.3 Emergency Maintenance for M2000 Client 14-1..........................................14.3.1 Function Introduction 14-1...................................................................14.3.2 Operation Procedure 14-2....................................................................
Chapter 15 Command Guide 15-1..........................................................................
15.1 Overview of Command Guide 15-1..............................................................15.2 Introduction to Commands 15-1...................................................................
15.2.1 Path of Commands 15-1......................................................................15.2.2 Prerequisites of Using Commands 15-1..............................................
15.3 svc_profile.sh 15-1.......................................................................................15.3.1 Function of svc_profile.sh 15-1............................................................
15.3.2 Path of svc_profile.sh 15-1...................................................................15.3.3 Running svc_profile.sh 15-1.................................................................
15.4 start_svc 15-2...............................................................................................15.4.1 Command Function 15-2......................................................................15.4.2 Example 15-2.......................................................................................
15.5 stop_svc 15-3...............................................................................................15.5.1 Command Function 15-3......................................................................15.5.2 Example 15-3.......................................................................................
15.6 kill_svc 15-3..................................................................................................15.6.1 Command Function 15-3......................................................................15.6.2 Example 15-3.......................................................................................
15.7 svc_adm-cmd status 15-3............................................................................15.7.1 Command Function 15-3......................................................................15.7.2 Example 15-3.......................................................................................
15.8 svc_ps 15-4..................................................................................................15.8.1 Command Function 15-4......................................................................15.8.2 Example 15-4.......................................................................................
15.9 top 15-4........................................................................................................15.9.1 Command Function 15-4......................................................................15.9.2 Example 15-4.......................................................................................
15.10 svc_adm-cmd reload 15-5..........................................................................15.10.1 Command Function 15-5....................................................................15.10.2 Example 15-5.....................................................................................
15.11 svc_stacks 15-5..........................................................................................15.11.1 Command Function 15-5....................................................................15.11.2 Example 15-5.....................................................................................
15.12 svc_lockdump 15-6.....................................................................................15.12.1 Command Function 15-6....................................................................15.12.2 Example 15-6.....................................................................................
Chapter 16 Tool Guide 16-1....................................................................................
16.1 Overview of Tool Guide 16-1........................................................................16.2 Tape Drive Management Tool 16-1..............................................................
16.2.1 Function 16-1.......................................................................................16.2.2 Starting method 16-1............................................................................16.2.3 Operation Guide 16-2...........................................................................
16.3 M2000 Diagnostic Tooling 16-2....................................................................16.3.1 Function 16-2.......................................................................................16.3.2 Running Diagnostic Tool 16-3..............................................................16.3.3 Abnormal Handling 16-5......................................................................16.3.4 Forbidding Using Diagnostic Tool 16-5................................................
16.4 Performance Job Result Auto Export Tool 16-5...........................................16.4.1 Function 16-5.......................................................................................16.4.2 Function Settings 16-5.........................................................................16.4.3 Running Auto Export Tool 16-6............................................................16.4.4 Stopping Auto Export Tool 16-7...........................................................16.4.5 Abnormal Handling 16-7......................................................................
16.5 IP Modification Tool 16-8..............................................................................16.5.1 Function 16-8.......................................................................................16.5.2 Prerequisites 16-8................................................................................16.5.3 Querying IP Settings 16-8....................................................................16.5.4 Modifying Solaris IP Address, Host name, Default Gatewayand Subnet Mask 16-9....................................................................................16.5.5 Modifying Sybase IP 16-9....................................................................16.5.6 Modifying Sybase Service IP and Port Number 16-10...........................16.5.7 Modifying Host Name 16-10...................................................................16.5.8 Modifying Gateway 16-10......................................................................
Chapter 17 FAQ 17-1................................................................................................
17.1 Overview of FAQ 17-1..................................................................................17.2 Logging in as root though Telnet 17-1..........................................................
17.2.1 Question 17-1.......................................................................................17.2.2 Answer 17-1.........................................................................................
17.3 Logging in as root though FTP 17-1.............................................................17.3.1 Question 17-1.......................................................................................17.3.2 Answer 17-1.........................................................................................
17.4 Installing Tape Drive 17-2.............................................................................17.4.1 Question 17-2.......................................................................................17.4.2 Answer 17-2.........................................................................................
17.5 Setting Default Route 17-3...........................................................................17.5.1 Question 17-3.......................................................................................17.5.2 Answer 17-3.........................................................................................
17.6 Adding and Deleting Routes 17-3.................................................................17.6.1 Question 17-3.......................................................................................17.6.2 Answer 17-3.........................................................................................
17.7 "/etc/rc2.d" in Solaris 17-4............................................................................17.7.1 Question 17-4.......................................................................................17.7.2 Answer 17-4.........................................................................................
17.8 Querying Hardware Configuration of Server 17-4........................................17.8.1 Question 17-4.......................................................................................17.8.2 Answer 17-4.........................................................................................
17.9 Confirming Startup of Sybase 17-5..............................................................
17.9.1 Question 17-5.......................................................................................17.9.2 Answer 17-5.........................................................................................
17.10 Starting Sybase 17-5..................................................................................17.10.1 Question 17-5.....................................................................................17.10.2 Answer 17-5.......................................................................................
17.11 Stopping Sybase 17-6................................................................................17.11.1 Question 17-6.....................................................................................17.11.2 Answer 17-6.......................................................................................
Appendix Acronyms and Abbreviations 1.......................................................
Index .................................................................................................................
HUAWEI
iManager M2000 Mobile Element Management System Administrator Guide
V200R002
iManager M2000 Mobile Element Management System
Administrator Guide
Manual Version T2-030159-20041010-C-2.20
Product Version V200R002
BOM 31014659
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co., Ltd.,
Bantian, Longgang District, Shenzhen, P. R. China
Postal Code: 518129
Website: http://www.huawei.com
Email: [email protected]
Copyright © 2004 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks
, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess, ETS, DMC,
TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, M900/M1800, TELESIGHT, Quidview, Musa, Airbridge, Tellwin, Inmedia, VRP, DOPRA, iTELLIN, HUAWEI OptiX, C&C08 iNET, NETENGINE, OptiX, iSite, U-SYS, iMUSE, OpenEye, Lansway, SmartAX, infoX, TopEng are trademarks of Huawei Technologies Co., Ltd.
All other trademarks mentioned in this manual are the property of their respective holders.
Notice
The information in this manual is subject to change without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information, and recommendations in this manual do not constitute the warranty of any kind, express or implied.
Summary of Updates
This section provides the update history of this manual and introduces the contents of subsequent updates.
Update History
This manual is updated for a major product version to maintain consistency with system hardware or software versions and to incorporate customer suggestions.
Manual Version Notes
T2-030159-20041010-C-2.20 Initial field trial release
Updates of Contents
None.
About This Manual
Release Notes
This manual applies to iManager M2000 Mobile Element Management System V200R002.
Organization
This manual provides the system administration tasks, the related concepts and detailed operation procedures of the system administration tasks, as well as the routine maintenance, troubleshooting and emergency maintenance. This manual consists of 17 chapters and one appendix:
Chapter 1 Overview of Administrator Guide introduces the objective, contents and the requirement of an administrator.
Chapter 2 Server Parameter Settings introduces the setting and modification of server parameters.
Chapter 3 User Management introduces the concepts related to user management and provides the details of the major user management tasks.
Chapter 4 Log Management introduces the concepts related to log management and provides the details of the major log management tasks.
Chapter 5 Server Performance Monitor introduces the concepts related to server performance monitor and provides the details of the major server performance monitor tasks.
Chapter 6 M2000 Process and Service Management introduces the concepts related to M2000 process and service management and provides the details of the major M2000 process and service management tasks.
Chapter 7 Database Management introduces the concepts related to database management and provides the details of the major database management tasks.
Chapter 8 Disk Space Management introduces the concepts related to disk space management and provides the details of the major disk space management tasks.
Chapter 9 Maintenance Dual-Plane Configuration introduces the concepts related to maintenance dual-plane configuration and provides the details of the major maintenance dual-plane configuration tasks.
Chapter 10 NTP Service Configuration introduces the concepts related to NTP service configuration and provides the details of the major NTP service configuration tasks.
Chapter 11 Backup and Restore introduces the concepts related to backup and restore and provides the details of the major backup and restore tasks.
Chapter 12 Routine Maintenance provides the maintenance items for M2000 and the operation guide.
Chapter 13 Troubleshooting introduces command troubleshooting procedure and some cases of troubleshooting.
Chapter 14 Emergency Maintenance provides the operation guide of emergency maintenance when serious failure occurs to the M2000 or client.
Chapter 15 Command Guide introduces functions and usage of the important commands.
Chapter 16 Tool Guide introduces the functions and usage of the M2000 tools.
Chapter 17 FAQ introduces the frequently asked question and the solutions concerning operating system and database.
Appendix Acronyms and Abbreviations lists the abbreviations and acronyms in this manual.
Intended Audience
The manual is intended for the following readers:
System engineer of mobile network M2000 administrator Network administrator
Conventions
The manual uses the following conventions:
I. General conventions
Convention Description
Arial Normal paragraphs are in Arial.
Arial Narrow Warnings, Cautions, Notes and Tips are in Arial Narrow.
Boldface Headings are in Boldface.
Courier New Terminal Display is in Courier New.
II. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are optional.
{ x | y | ... } Alternative items are grouped in braces and separated by vertical bars. One is selected.
[ x | y | ... ] Optional alternative items are grouped in square brackets and separated by vertical bars. One or none is selected.
{ x | y | ... } * Alternative items are grouped in braces and separated by vertical bars. A minimum of one or a maximum of all can be selected.
[ x | y | ... ] * Optional alternative items are grouped in square brackets and separated by vertical bars. Many or none can be selected.
III. GUI conventions
Convention Description
< > Button names are inside angle brackets. For example, click the <OK> button.
[ ] Window names, menu items, data table and field names are inside square brackets. For example, pop up the [New User] window.
/ Multi-level menus are separated by forward slashes. For example, [File/Create/Folder].
IV. Keyboard operation
Format Description
<Key> Press the key with the key name inside angle brackets. For example, <Enter>, <Tab>, <Backspace>, or <A>.
<Key1+Key2> Press the keys concurrently. For example, <Ctrl+Alt+A> means the three keys should be pressed concurrently.
<Key1, Key2> Press the keys in turn. For example, <Alt, A> means the two keys should be pressed in turn.
V. Mouse operation
Action Description
Click Press the left button or right button quickly (left button by default).
Double Click Press the left button twice continuously and quickly.
Drag Press and hold the left button and drag it to a certain position.
VI. Symbols
Eye-catching symbols are also used in the manual to highlight the points worthy of special attention during the operation. They are defined as follows:
Caution, Warning, Danger: Means reader be extremely careful during the
operation.
Note, Comment, Tip, Knowhow, Thought: Means a complementary description.
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
i
Table of Contents
Table of Contents .............................................................................................................................. i
Chapter 1 Overview of Administrator Guide .............................................................................. 1-1 1.1 Objective ............................................................................................................................ 1-1 1.2 Requirements for Administrator ......................................................................................... 1-1 1.3 Organization of This Guide ................................................................................................ 1-2
1.3.1 Administrative Tasks ............................................................................................... 1-2 1.3.2 Maintenance Items.................................................................................................. 1-2 1.3.3 Commands and Tools ............................................................................................. 1-2 1.3.4 FAQ ......................................................................................................................... 1-3
Chapter 2 Server Parameter Settings.......................................................................................... 2-1 2.1 Overview of Server Parameter Settings ............................................................................ 2-1 2.2 Modifying Server Time....................................................................................................... 2-1
2.2.1 Operation Effect ...................................................................................................... 2-1 2.2.2 Operation Procedure............................................................................................... 2-1
2.3 Modifying Host name of Server ......................................................................................... 2-2 2.3.1 Operation Effect ...................................................................................................... 2-2 2.3.2 Operation Procedure............................................................................................... 2-2
2.4 Modifying Server IP Address ............................................................................................. 2-3 2.4.1 Operation Effect ...................................................................................................... 2-3 2.4.2 Operation Procedure............................................................................................... 2-3
2.5 Setting Parameters of Server with Multiple IPs ................................................................. 2-4 2.5.1 Operation Effect ...................................................................................................... 2-4 2.5.2 Operation Procedure............................................................................................... 2-5
Chapter 3 User Management........................................................................................................ 3-1 3.1 Overview of User Management ......................................................................................... 3-1 3.2 Introduction to User Account ............................................................................................. 3-1
3.2.1 Types of User Account............................................................................................ 3-1 3.2.2 Operating System User Accounts and the Authority............................................... 3-1 3.2.3 Database User Account and the Authority.............................................................. 3-3 3.2.4 M2000 User Accounts and the Authority ................................................................ 3-3
3.3 Creating Operating System User....................................................................................... 3-3 3.3.1 Operation Effect ...................................................................................................... 3-3 3.3.2 Operation Procedure............................................................................................... 3-3
3.4 Modifying Password of Operating System User ................................................................ 3-4 3.4.1 Operation Effect ...................................................................................................... 3-4 3.4.2 Modifying Password of root..................................................................................... 3-4
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
ii
3.4.3 Modifying Password of dbuser ................................................................................ 3-4 3.4.4 Modifying Password of omcuser ............................................................................. 3-4 3.4.5 Modifying Password of ftpuser ................................................................................ 3-4
3.5 Modifying Password of Database User ............................................................................. 3-5 3.5.1 Operation Effect ...................................................................................................... 3-5 3.5.2 Operation Procedure............................................................................................... 3-5
3.6 Creating M2000 User Group.............................................................................................. 3-6 3.6.1 Operation Effect ...................................................................................................... 3-6 3.6.2 Operation Procedure............................................................................................... 3-6
3.7 Creating M2000 User Account........................................................................................... 3-6 3.7.1 Operation Effect ...................................................................................................... 3-6 3.7.2 Operation Procedure............................................................................................... 3-6
3.8 Monitoring M2000 Users.................................................................................................... 3-6 3.8.1 Operation Effect ...................................................................................................... 3-6 3.8.2 Operation Procedure............................................................................................... 3-7
Chapter 4 Log Management ......................................................................................................... 4-1 4.1 Overview of Log Management........................................................................................... 4-1 4.2 Introduction to Log ............................................................................................................. 4-1
4.2.1 Types of Logs.......................................................................................................... 4-1 4.2.2 User Log.................................................................................................................. 4-1 4.2.3 NE Log .................................................................................................................... 4-1 4.2.4 System Log ............................................................................................................. 4-2 4.2.5 Trace log ................................................................................................................. 4-2
4.3 Browsing User Log ............................................................................................................ 4-3 4.3.1 Operation Effect ...................................................................................................... 4-3 4.3.2 Operation Procedure............................................................................................... 4-3
4.4 Browsing System Log ........................................................................................................ 4-3 4.4.1 Operation Effect ...................................................................................................... 4-3 4.4.2 Operation Procedure............................................................................................... 4-3
4.5 Checking Solaris Error Log................................................................................................ 4-3 4.5.1 Operation Effect ...................................................................................................... 4-3 4.5.2 Operation Procedure............................................................................................... 4-3
Chapter 5 Server Performance Monitor ...................................................................................... 5-1 5.1 Overview of Server Performance Monitor ......................................................................... 5-1 5.2 Querying Server Status through Client.............................................................................. 5-1
5.2.1 Function................................................................................................................... 5-1 5.2.2 Operation Procedure............................................................................................... 5-1
5.3 Setting the Threshold of Server Status Alarm ................................................................... 5-2 5.3.1 Function................................................................................................................... 5-2 5.3.2 Operation Procedure............................................................................................... 5-2
5.4 Querying System Performance.......................................................................................... 5-2 5.4.1 Operation Effect ...................................................................................................... 5-2
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
iii
5.4.2 Operation Procedure............................................................................................... 5-3 5.5 Adjusting System Performance ......................................................................................... 5-3
5.5.1 Operation Effect ...................................................................................................... 5-3 5.5.2 Operation Procedure............................................................................................... 5-4
Chapter 6 M2000 Process and Service Management ................................................................ 6-1 6.1 Overview of M2000 Process and Service Management.................................................... 6-1 6.2 Introduction to M2000 Processes and Services ................................................................ 6-1
6.2.1 Overview to Processes and Services ..................................................................... 6-1 6.2.2 SystemConfigurator ................................................................................................ 6-1 6.2.3 sac_agent................................................................................................................ 6-1 6.2.4 em_agent ................................................................................................................ 6-2 6.2.5 monitor_agent ......................................................................................................... 6-2 6.2.6 partition_agent......................................................................................................... 6-3 6.2.7 audit_agent.............................................................................................................. 6-3 6.2.8 mo_agent ................................................................................................................ 6-3 6.2.9 sm_agent................................................................................................................. 6-4 6.2.10 med_agent ............................................................................................................ 6-4 6.2.11 ts_agent................................................................................................................. 6-4 6.2.12 ifms_agent............................................................................................................. 6-4 6.2.13 manager_agent ..................................................................................................... 6-4 6.2.14 pm_agent .............................................................................................................. 6-5 6.2.15 cmserver_agent..................................................................................................... 6-5 6.2.16 swm_agent ............................................................................................................ 6-5 6.2.17 fmnotify_agent....................................................................................................... 6-5 6.2.18 proxy_agent........................................................................................................... 6-6 6.2.19 notify_agent........................................................................................................... 6-6
6.3 Querying Number of M2000 Processes ............................................................................ 6-6 6.3.1 Operation Effect ...................................................................................................... 6-6 6.3.2 Operation Procedure............................................................................................... 6-6
6.4 Querying Service Status .................................................................................................... 6-6 6.4.1 Operation Effect ...................................................................................................... 6-6 6.4.2 Operation Procedure............................................................................................... 6-6
6.5 Starting M2000 Services.................................................................................................... 6-8 6.5.1 Operation Effect ...................................................................................................... 6-8 6.5.2 Operation Procedure............................................................................................... 6-8
6.6 Stopping M2000 Services.................................................................................................. 6-9 6.6.1 Operation Effect ...................................................................................................... 6-9 6.6.2 Operation Procedure............................................................................................... 6-9
Chapter 7 Database Management................................................................................................ 7-1 7.1 Overview of Database Management ................................................................................. 7-1 7.2 Introduction to Database.................................................................................................... 7-1
7.2.1 Overview of Database............................................................................................. 7-1
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
iv
7.2.2 omcdb...................................................................................................................... 7-1 7.2.3 fmdb ........................................................................................................................ 7-2 7.2.4 pmdb ....................................................................................................................... 7-2 7.2.5 sysmdb .................................................................................................................... 7-3
7.3 Querying Database Status................................................................................................. 7-4 7.3.1 Operation Effect ...................................................................................................... 7-4 7.3.2 Operation Procedure............................................................................................... 7-4
7.4 Manually Displacing Alarm Data........................................................................................ 7-5 7.4.1 Operation Effect ...................................................................................................... 7-5 7.4.2 Operation Procedure............................................................................................... 7-5
7.5 Manually Displacing User Log ........................................................................................... 7-5 7.5.1 Operation Effect ...................................................................................................... 7-5 7.5.2 Operation Procedure............................................................................................... 7-6
7.6 Setting Auto Displacing for Alarm Data ............................................................................. 7-6 7.6.1 Operation Effect ...................................................................................................... 7-6 7.6.2 Operation Procedure............................................................................................... 7-6
7.7 Setting Auto Displacing for User Log................................................................................. 7-7 7.7.1 Operation Effect ...................................................................................................... 7-7 7.7.2 Operation Procedure............................................................................................... 7-7
7.8 Deleting Performance Task ............................................................................................... 7-7 7.8.1 Operation Effect ...................................................................................................... 7-7 7.8.2 Operation Procedure............................................................................................... 7-7
7.9 Clearing Database ............................................................................................................. 7-8 7.9.1 Operation Effect ...................................................................................................... 7-8 7.9.2 Operation Procedure............................................................................................... 7-8
Chapter 8 Disk Space Management............................................................................................. 8-1 8.1 Overview of Disk Space Management .............................................................................. 8-1 8.2 Introduction to File System ................................................................................................ 8-1
8.2.1 Overview of System Structure................................................................................. 8-1 8.2.2 Server File System.................................................................................................. 8-1 8.2.3 Client File System ................................................................................................... 8-2
8.3 Query Disk Space.............................................................................................................. 8-2 8.3.1 Operation Effect ...................................................................................................... 8-2 8.3.2 Operation Procedure............................................................................................... 8-3
8.4 Clearing Disk Space .......................................................................................................... 8-3 8.4.1 Operation Effect ...................................................................................................... 8-3 8.4.2 Operation Procedure............................................................................................... 8-3
Chapter 9 Dual-Plane Configuration............................................................................................ 9-1 9.1 Overview of Dual-Plane Configuration .............................................................................. 9-1 9.2 Introduction to Dual-Plane ................................................................................................. 9-1 9.3 Configuration Procedure of Dual-Plane............................................................................. 9-2 9.4 Planning IP Data................................................................................................................ 9-2
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
v
9.5 Manually Setting Dual-Plane ............................................................................................. 9-2 9.5.1 Operation Effect ...................................................................................................... 9-2 9.5.2 Operation Procedure............................................................................................... 9-2
9.6 Automatically Setting Dual-Plane ...................................................................................... 9-3 9.6.1 Operation Effect ...................................................................................................... 9-3 9.6.2 Operation Procedure............................................................................................... 9-3
9.7 Verifying Dual-Plane Settings ............................................................................................ 9-4 9.7.1 Operation Effect ...................................................................................................... 9-4 9.7.2 Operation Procedure............................................................................................... 9-4 9.7.3 Abnormal Handling.................................................................................................. 9-4
Chapter 10 NTP Service Configuration ..................................................................................... 10-1 10.1 Overview of NTP Service Configuration ........................................................................ 10-1 10.2 Introduction to NTP Service........................................................................................... 10-1 10.3 Setting M2000 as Top NTP Server................................................................................ 10-2 10.4 Setting M2000 as Middle NTP Server ........................................................................... 10-2 10.5 Setting M2000 as NTP Client ........................................................................................ 10-2 10.6 Starting NTP Service ..................................................................................................... 10-2 10.7 Checking Running Status of NTP Service..................................................................... 10-3 10.8 Stopping NTP Service ................................................................................................... 10-3
Chapter 11 Backup and Restoration ......................................................................................... 11-1 11.1 Overview of Backup and Restoration ............................................................................ 11-1 11.2 Introduction to Backup and Restoration ........................................................................ 11-1
11.2.1 M2000 System Backup Contents........................................................................ 11-1 11.2.2 M2000 System Backup and NE Data Backup .................................................... 11-1 11.2.3 The Mode of M2000 System Backup and Restore ............................................. 11-2 11.2.4 Name of Backup Files ......................................................................................... 11-2 11.2.5 Storage Media of Backup File ............................................................................. 11-2
11.3 Function Setting............................................................................................................. 11-3 11.3.1 Introduction to Configuration File ........................................................................ 11-3 11.3.2 Setting Tape Drive Path ...................................................................................... 11-3 11.3.3 Setting Backup Media ......................................................................................... 11-3
11.4 Automatically Backing Up M2000 System..................................................................... 11-4 11.4.1 Introduction to Auto Backup................................................................................ 11-4 11.4.2 Setting Auto Backup Time................................................................................... 11-5
11.5 Manually Backing Up M2000 System............................................................................ 11-5 11.5.1 Introduction to Manual Backup............................................................................ 11-5 11.5.2 Carrying Out Manual Backup on Client............................................................... 11-5 11.5.3 Carrying Out Manual Backup on Server ............................................................. 11-6
11.6 Restoring M2000 System .............................................................................................. 11-6 11.6.1 Function Introduction........................................................................................... 11-6 11.6.2 Operation Procedure........................................................................................... 11-6
11.7 Backing Up Operating System....................................................................................... 11-7
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
vi
11.7.1 Function Introduction........................................................................................... 11-7 11.7.2 Operation Procedure........................................................................................... 11-7
11.8 Restoring Operating System.......................................................................................... 11-9 11.8.1 Function Introduction........................................................................................... 11-9 11.8.2 Operation Procedure........................................................................................... 11-9 11.8.3 Restoring Tape Information................................................................................. 11-9 11.8.4 Setting Up Equipment Tree and Boot Block ..................................................... 11-10 11.8.5 Modifying System File and File System Information......................................... 11-11 11.8.6 Restarting System............................................................................................. 11-12 11.8.7 Encapsulating Disk Using Volume Manager..................................................... 11-12
Chapter 12 Routine Maintenance............................................................................................... 12-1 12.1 Overview of Routine Maintenance................................................................................. 12-1 12.2 Daily Maintenance ......................................................................................................... 12-1
12.2.1 Daily Maintenance Item List ................................................................................ 12-1 12.2.2 Checking Alarm Information................................................................................ 12-1 12.2.3 Checking Log Information ................................................................................... 12-2 12.2.4 Checking Solaris Error Log ................................................................................. 12-2 12.2.5 Checking Database Status.................................................................................. 12-2 12.2.6 Checking Hard Disk Space ................................................................................. 12-2 12.2.7 Checking CPU Utilization .................................................................................... 12-2 12.2.8 Checking Number of Processes.......................................................................... 12-2 12.2.9 Checking Service Status ..................................................................................... 12-3
12.3 Weekly Maintenance ..................................................................................................... 12-3 12.3.1 Weekly Maintenance Item List ............................................................................ 12-3 12.3.2 Backing Up M2000 System................................................................................. 12-3 12.3.3 Checking M2000 Server Time............................................................................. 12-3 12.3.4 Finding core Files................................................................................................ 12-4 12.3.5 Clearing Useless Files ........................................................................................ 12-4
12.4 Monthly Maintenance..................................................................................................... 12-4 12.4.1 Monthly Maintenance Item List ........................................................................... 12-4 12.4.2 Checking Power Supply ...................................................................................... 12-4 12.4.3 Checking Server Hardware ................................................................................. 12-4 12.4.4 Checking Auxiliary Devices of Server ................................................................. 12-4
Chapter 13 Troubleshooting ...................................................................................................... 13-1 13.1 Overview of Troubleshooting ......................................................................................... 13-1 13.2 Troubleshooting Procedure ........................................................................................... 13-1
13.2.1 Overview of Troubleshooting Procedure............................................................. 13-1 13.2.2 Information Collection ......................................................................................... 13-1 13.2.3 Fault Location...................................................................................................... 13-1 13.2.4 Fault Clearance................................................................................................... 13-2
13.3 Auto Shutdown of Operating System ............................................................................ 13-2 13.3.1 Symptom ............................................................................................................. 13-2
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
vii
13.3.2 Fault Analysis ...................................................................................................... 13-2 13.3.3 Fault Clearance................................................................................................... 13-3
13.4 Abnormal Service Restart.............................................................................................. 13-3 13.4.1 Symptom ............................................................................................................. 13-3 13.4.2 Fault Analysis ...................................................................................................... 13-3 13.4.3 Fault Clearance................................................................................................... 13-3
13.5 Abnormal Service Termination ...................................................................................... 13-4 13.5.1 Symptom ............................................................................................................. 13-4 13.5.2 Fault Analysis ...................................................................................................... 13-4 13.5.3 Fault Clearance................................................................................................... 13-4
13.6 M2000 Services Starting or Stopping Failure ................................................................ 13-5 13.6.1 Symptom ............................................................................................................. 13-5 13.6.2 Fault Analysis ...................................................................................................... 13-5 13.6.3 Fault Clearance................................................................................................... 13-5
Chapter 14 Emergency Maintenance......................................................................................... 14-1 14.1 Overview of Emergency Maintenance........................................................................... 14-1 14.2 Emergency Maintenance for M2000 Server .................................................................. 14-1
14.2.1 Function Introduction........................................................................................... 14-1 14.2.2 Operation Procedure........................................................................................... 14-1
14.3 Emergency Maintenance for M2000 Client ................................................................... 14-1 14.3.1 Function Introduction........................................................................................... 14-1 14.3.2 Operation Procedure........................................................................................... 14-2
Chapter 15 Command Guide ...................................................................................................... 15-1 15.1 Overview of Command Guide........................................................................................ 15-1 15.2 Introduction to Commands............................................................................................. 15-1
15.2.1 Path of Commands ............................................................................................. 15-1 15.2.2 Prerequisites of Using Commands...................................................................... 15-1
15.3 svc_profile.sh................................................................................................................. 15-1 15.3.1 Function of svc_profile.sh ................................................................................... 15-1 15.3.2 Path of svc_profile.sh.......................................................................................... 15-1 15.3.3 Running svc_profile.sh........................................................................................ 15-1
15.4 start_svc......................................................................................................................... 15-2 15.4.1 Command Function............................................................................................. 15-2 15.4.2 Example .............................................................................................................. 15-2
15.5 stop_svc......................................................................................................................... 15-3 15.5.1 Command Function............................................................................................. 15-3 15.5.2 Example .............................................................................................................. 15-3
15.6 kill_svc ........................................................................................................................... 15-3 15.6.1 Command Function............................................................................................. 15-3 15.6.2 Example .............................................................................................................. 15-3
15.7 svc_adm –cmd status .................................................................................................... 15-3 15.7.1 Command Function............................................................................................. 15-3
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
viii
15.7.2 Example .............................................................................................................. 15-3 15.8 svc_ps............................................................................................................................ 15-4
15.8.1 Command Function............................................................................................. 15-4 15.8.2 Example .............................................................................................................. 15-4
15.9 top .................................................................................................................................. 15-4 15.9.1 Command Function............................................................................................. 15-4 15.9.2 Example .............................................................................................................. 15-4
15.10 svc_adm –cmd reload.................................................................................................. 15-5 15.10.1 Command Function........................................................................................... 15-5 15.10.2 Example ............................................................................................................ 15-5
15.11 svc_stacks ................................................................................................................... 15-5 15.11.1 Command Function........................................................................................... 15-5 15.11.2 Example ............................................................................................................ 15-5
15.12 svc_lockdump .............................................................................................................. 15-6 15.12.1 Command Function........................................................................................... 15-6 15.12.2 Example ............................................................................................................ 15-6
Chapter 16 Tool Guide ................................................................................................................ 16-1 16.1 Overview of Tool Guide ................................................................................................. 16-1 16.2 Tape Drive Management Tool ....................................................................................... 16-1
16.2.1 Function............................................................................................................... 16-1 16.2.2 Starting method................................................................................................... 16-1 16.2.3 Operation Guide.................................................................................................. 16-2
16.3 M2000 Diagnostic Tooling ............................................................................................. 16-2 16.3.1 Function............................................................................................................... 16-2 16.3.2 Running Diagnostic Tool ..................................................................................... 16-3 16.3.3 Abnormal Handling.............................................................................................. 16-5 16.3.4 Forbidding Using Diagnostic Tool ....................................................................... 16-5
16.4 Performance Job Result Auto Export Tool .................................................................... 16-5 16.4.1 Function............................................................................................................... 16-5 16.4.2 Function Settings ................................................................................................ 16-5 16.4.3 Running Auto Export Tool ................................................................................... 16-6 16.4.4 Stopping Auto Export Tool .................................................................................. 16-7 16.4.5 Abnormal Handling.............................................................................................. 16-7
16.5 IP Modification Tool ....................................................................................................... 16-8 16.5.1 Function............................................................................................................... 16-8 16.5.2 Prerequisites ....................................................................................................... 16-8 16.5.3 Querying IP Settings ........................................................................................... 16-8 16.5.4 Modifying Solaris IP Address, Host name, Default Gateway and Subnet Mask. 16-9 16.5.5 Modifying Sybase IP ........................................................................................... 16-9 16.5.6 Modifying Sybase Service IP and Port Number................................................ 16-10 16.5.7 Modifying Host Name........................................................................................ 16-10 16.5.8 Modifying Gateway............................................................................................ 16-10
Administrator Guide iManager M2000 Mobile Element Management System Table of Contents
ix
Chapter 17 FAQ ........................................................................................................................... 17-1 17.1 Overview of FAQ ........................................................................................................... 17-1 17.2 Logging in as root though Telnet ................................................................................... 17-1
17.2.1 Question .............................................................................................................. 17-1 17.2.2 Answer ................................................................................................................ 17-1
17.3 Logging in as root though FTP ...................................................................................... 17-1 17.3.1 Question .............................................................................................................. 17-1 17.3.2 Answer ................................................................................................................ 17-1
17.4 Installing Tape Drive ...................................................................................................... 17-2 17.4.1 Question .............................................................................................................. 17-2 17.4.2 Answer ................................................................................................................ 17-2
17.5 Setting Default Route..................................................................................................... 17-3 17.5.1 Question .............................................................................................................. 17-3 17.5.2 Answer ................................................................................................................ 17-3
17.6 Adding and Deleting Routes .......................................................................................... 17-3 17.6.1 Question .............................................................................................................. 17-3 17.6.2 Answer ................................................................................................................ 17-3
17.7 "/etc/rc2.d" in Solaris...................................................................................................... 17-4 17.7.1 Question .............................................................................................................. 17-4 17.7.2 Answer ................................................................................................................ 17-4
17.8 Querying Hardware Configuration of Server ................................................................. 17-4 17.8.1 Question .............................................................................................................. 17-4 17.8.2 Answer ................................................................................................................ 17-4
17.9 Confirming Startup of Sybase........................................................................................ 17-5 17.9.1 Question .............................................................................................................. 17-5 17.9.2 Answer ................................................................................................................ 17-5
17.10 Starting Sybase ........................................................................................................... 17-5 17.10.1 Question ............................................................................................................ 17-5 17.10.2 Answer .............................................................................................................. 17-5
17.11 Stopping Sybase.......................................................................................................... 17-6 17.11.1 Question ............................................................................................................ 17-6 17.11.2 Answer .............................................................................................................. 17-6
Appendix Acronyms and Abbreviations........................................................................................ 1
Index ................................................................................................................................................ i-1
Administrator Guide iManager M2000 Mobile Element Management System Chapter 1 Overview of Administrator Guide
1-1
Chapter 1 Overview of Administrator Guide
1.1 Objective The documentation package of iManager M2000 Mobile Element Management System (M2000 for short) contains two task-oriented manuals: iManager M2000 Mobile Element Management System Administrator Guide and iManager M2000 Mobile Element Management System Operation Manual.
iManager M2000 Mobile Element Management System Administrator Guide
The intended reader of this guide is system administrator. This guide provides the related concepts and detailed operation procedures of the system administration tasks. This guide focuses on M2000 single-server system administration, including Server status monitoring, database management, disk space management, user management, system backup and restoration, and general fault handling.
iManager M2000 Mobile Element Management System Operation Manual
The intended reader of this manual is M2000 operator. This manual provides the related concepts and detailed operation procedures of the operation tasks. This manual focuses on operations and maintenance of the mobile networks through M2000, including network performance monitoring, alarm query, NE configuration, NE software upgrade and entire network data backup and restoring.
1.2 Requirements for Administrator The system administrator of M2000 must be familiar with the following items:
Solaris and Windows operating systems Sybase database Knowledge of computer networks such as Ethernet, TCP/IP, and Client/Server M2000 system and its functions
Refer to iManager M2000 Mobile Element Management System Description and this guide.
Installation of M2000 Server and Client application software
Refer to iManager M2000 Mobile Element Management System Installation Manual
Operation on M2000 Client
Refer to iManager M2000 Mobile Element Management System Online Help and iManager M2000 Mobile Element Management System operation Manual.
Routine maintenance and troubleshooting on M2000
Administrator Guide iManager M2000 Mobile Element Management System Chapter 1 Overview of Administrator Guide
1-2
Refer to "Chapter 12 Routine Maintenance", "Chapter 13 Troubleshooting" and "Chapter 14 Emergency Maintenance" in this guide.
1.3 Organization of This Guide
1.3.1 Administrative Tasks
This guide introduces the following administrative tasks and the related concepts:
Server parameter setting User management Log management Server performance monitor M2000 process and service management Database management Disk space management Dual-plane configuration NTP service configuration Backup and restoration
Each of the above tasks is explained in an individual chapter. The first section of each chapter describes the structure of the chapter, the second section introduces the task concepts and the third section explains the task details. The second section may not be applicable for a few chapters, and so, may not be present.
1.3.2 Maintenance Items
This guide also introduces the following maintenance items based on administration tasks:
Routine maintenance Troubleshooting Emergency maintenance
This part is concerning on M2000.
For the maintenance and fault handling of Solaris operating system or Sybase database, refer to Solaris system administrator manual or Sybase system administrator manual.
For operation and maintenance of NE, refer to iManager M2000 Mobile Element Management System Operation Manual, and NE’s corresponding manual.
1.3.3 Commands and Tools
This guide also introduces M2000 commands and tools in system administration:
Command guide Tool guide
Administrator Guide iManager M2000 Mobile Element Management System Chapter 1 Overview of Administrator Guide
1-3
1.3.4 FAQ
This guide also introduces the frequently asked question and the solutions concerning Solaris operating system and Sybase database.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 2 Server Parameter Settings
2-1
Chapter 2 Server Parameter Settings
2.1 Overview of Server Parameter Settings This chapter introduces the modifications and settings of the Server parameters, including:
Modifying Server time Modifying host name of Server Modifying IP address of Server Setting multiple IPs for Server
2.2 Modifying Server Time
2.2.1 Operation Effect
System time modification during M2000 running will affect the system timer, thus disabling the timed cleaning of the database tempdb. When tempdb is full, Sybase cannot work and M2000 cannot run.
It is necessary to stop M2000 services if you want to modify system time, and thus M2000 can not process the performance data and alarm data of the managed NEs when M2000 services are not running. After M2000 services have been restarted, M2000 will get the data from NEs by using auto synchronization function and then process the data.
2.2.2 Operation Procedure
To modify the Server time, perform the following operations on the Server:
1) Log in as root. 2) Execute the following commands to stop M2000 services.
# stop_svc
3) Execute the following command to stop Sybase.
# isql –SSYB –Usa –P<user sa password>
1> shutdown SYB_BACKUP
2> go
1> shutdown SYB
2> go
4) Execute the following command to check the time zone of the operating system.
# echo $TZ
Administrator Guide iManager M2000 Mobile Element Management System Chapter 2 Server Parameter Settings
2-2
If the current time zone is incorrect, modify the file "/etc/TIMEZONE" to change the value of "TZ" to the local time zone. For example, "TZ=PRC".
Note:
You can query the time zone information through "/usr/share/lib/zoneinfo".
5) Use the command "date" to set system date and time.
For example, to set the system date and time to 2003-11-17 16:30:43, execute the command:
# date 111716302003.43
Mon Nov 17 17:53:29 CST 2003
6) Execute the following command to restart the Server.
# init 6
When the operating system starts up, Sybase services and M2000 services will start automatically if M2000 Server software application has been installed.
2.3 Modifying Host name of Server
2.3.1 Operation Effect
Do not modify the host name of the Server during M2000 running. Otherwise, the M2000 services will stop abnormally.
It is necessary to stop M2000 services if you want to modify the host name, and thus M2000 can not process the performance data and alarm data of the managed NEs when M2000 services are not running. After M2000 services have been restarted, M2000 will get the data from NEs by using auto synchronization function and then process the data.
2.3.2 Operation Procedure
To change the host name of the Server, perform the following operations on the Server:
1) Log in as root. 2) Execute the following commands to stop M2000 services.
# stop_svc
3) Execute the following command to stop sybase.
# isql –SSYB –Usa –P<user sa password>
1> shutdown SYB_BACKUP
2> go
Administrator Guide iManager M2000 Mobile Element Management System Chapter 2 Server Parameter Settings
2-3
1> shutdown SYB
2> go
4) Use the IP modification tool to modify the host name.
# iptools -H host-name
For example, to set the host name to "omc":
# iptools -H omc
Note:
For the functions and usage of IP modification tool “iptools”, refer to "16.5 IP Modification Tool".
5) Edit the file "<M2000 installation directory>/etc/conf/tao.cfg". Change the original host name to the new host name.
6) Execute the following command to restart the Server.
# init 6
When the operating system starts up, Sybase services and M2000 services will start automatically if M2000 Server software application has been installed.
2.4 Modifying Server IP Address
2.4.1 Operation Effect
Do not modify the IP address of the Server during M2000 running. Otherwise, the M2000 services will stop abnormally.
It is necessary to stop M2000 services if you want to modify the Server IP address, and M2000 can not process the performance data and alarm data of the managed NEs when M2000 services are not running. After M2000 services have been restarted, M2000 will get the data from NEs by using auto synchronization function and then process the data.
2.4.2 Operation Procedure
To modify the IP address of the Server, perform the following operations on the Server:
1) Log in as root. 2) Execute the following commands to stop M2000 services.
# stop_svc
3) Execute the following command to stop sybase.
# isql –SSYB –Usa –P<user sa password>
1> shutdown SYB_BACKUP
Administrator Guide iManager M2000 Mobile Element Management System Chapter 2 Server Parameter Settings
2-4
2> go
1> shutdown SYB
2> go
4) Execute the following command to query the current IP settings.
# ifconfig –a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.161.45.241 netmask fffffe00 broadcast 10.161.45.255
ether 0:3:ba:12:f9:12
5) Use the IP modification tool to modify the IP settings in Solaris and Sybase.
Note:
For the functions and usage of IP modification tool, refer to "16.5 IP Modification Tool".
# iptools {-n interface-name -i ip-address -m subnet-mask -G default -gateway -H host-name -d }
For example, modify the IP of Solaris system as 10.70.141.54, host name as host, default gateway as 10.70.141.1, and all Server IPs of Sybase databases as 10.70.141.54.
# iptools –n eri0 –i 10.70.141.54 –m 255.255.255.0 –G 10.70.141.1 –H host –d
6) Execute the following command to restart the Server.
# init 6
When the operating system starts up, Sybase services and M2000 services will start automatically if M2000 Server software application has been installed.
2.5 Setting Parameters of Server with Multiple IPs
2.5.1 Operation Effect
When a Server has multiple IPs, it is necessary to specify one of them for M2000 services. Otherwise, the Client cannot set up connection with the Server.
It is necessary to stop M2000 services if you want to set multiple IPs, and thus M2000 can not process the performance data and alarm data of the managed NEs when M2000 services are not running. After M2000 services have been restarted, M2000 will get the data from NEs by using auto synchronization function and then process the data.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 2 Server Parameter Settings
2-5
2.5.2 Operation Procedure
To specify an IP for M2000 services, perform the following operations on the Server:
1) Log in as root. 2) Execute the following commands to stop M2000 services.
# stop_svc
3) Execute the following command to stop sybase.
# isql –SSYB –Usa –P<user sa password>
1> shutdown SYB_BACKUP
2> go
1> shutdown SYB
2> go
4) Edit the file "/etc/hosts", to make the host name correspond to an IP, which is used to connect the Client and managed NEs.
For example, among the two IP of the Server "10.161.70.200" and "10.121.5.208", "10.121.5.208" is used to connect the Client. "<M2000 installation directory>/etc/conf/tao.cfg" shows that the host name is "aries", then in the file "/etc/hosts", add a note "#" before "10.161.70.200".
#
# Internet host table
#
127.0.0.1 localhost
#10.161.70.200 aries loghost
10.121.5.208 aries loghost
5) Execute the following command to restart the Server.
# init 6
When the operating system starts up, Sybase services and M2000 services will start automatically if M2000 Server software application has been installed.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-1
Chapter 3 User Management
3.1 Overview of User Management This chapter introduces the concepts related to user management, including type and authority of user account, and provides the details of the major user management tasks, including:
Creating operating system user account Modifying operating system user account Modifying database user password of database Creating M2000 user group Creating M2000 user account Monitoring M2000 user
3.2 Introduction to User Account
3.2.1 Types of User Account
The operation of M2000 system involves three types of user accounts:
User account of operating system: For M2000 Server operations. User account of database: For M2000 Server database operations. User account of M2000: For M2000 Client operations.
3.2.2 Operating System User Accounts and the Authority
To carry out operations on M2000 Server, you should have a user account of the operating system.
Apart from the default user accounts of the operating system Solaris, you should create three user accounts, dbuser, omcuser, and ftpuser. You should also create a user group omcsysm.
If you install Report System, the installer will create the user account inrpt and the user group inrpt automatically.
I. root
The user root is with the highest authority to the system. This user can control all resources, create other users, grant authorities to other users, and perform all the operation functions provided by the operating system.
Only the user root can install and uninstall the M2000 Server application software, and start and stop M2000 services.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-2
II. dbuser
The user dbuser handles routine operation and maintenance of Sybase database. The user can perform any operation such as interaction with the database through isql on the database.
You should create dbuser before installing Sybase. The related attributes are as follows:
Home directory: /opt/sybase The group that it belongs to: staff Login shell: /bin/bash
III. omcuser
The user omcuser has the authority to perform routine operation and maintenance on the M2000 system, including querying system status, backing up and restoring system data. The user omcuser also has the authority to access databases. The user can neither install/uninstall M2000 Server application software, nor start/stop M2000 services.
You should create omcuser before installing the M2000 Server application software. The attributes of the user are as follows:
Home directory: /export/home/omc The primary group that it belongs to: staff. The secondary group that it belongs to: sys, root, omcsysm. Login shell: /bin/bash
IV. ftpuser
The user ftpuser manages software of NEs and transfers software information to NEs. You should create ftpuser before installing M2000 Server application software. The attributes of the user are as follows:
Home directory: /export/home/sysm The group that it belongs to: omcsysm Login shell: /bin/bash
V. inrpt
The user inrpt manages the Intelligent Report System. You do not need to create inrpt manually. When the Intelligent Report System is installed, the user inrpt will be created automatically. The attributes of the user are as follows:
Home directory: /opt/inrpt The group that it belongs to: inrpt Login shell: /usr/bin/csh
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-3
3.2.3 Database User Account and the Authority
To use M2000 Server database Sybase, you need a user account of Sybase.
The user sa is the default user account of Sybase. It has the highest administration authorities of the database.
For M2000 system, only the user sa is necessary.
3.2.4 M2000 User Accounts and the Authority
After the installation of M2000 Server and Client, the user "admin" and the user group "administrator" will be created. "admin" and "administrator" have all operation authorities to all NEs.
For detailed description of M2000 user account and authority, refer to iManager M2000 Mobile Element Management System Operation Manual.
3.3 Creating Operating System User
3.3.1 Operation Effect
After an operating system Solaris user account is created, the user information will be recorded in Solaris system file.
Before the installation of Sybase and M2000 Server software, it is necessary to create three users manually: dbuser, omcuser and ftpuser. For creating method, refer to iManager M2000 Mobile Element Management System Installation Manual. It is necessary to set password for each user and the password update period.
For details on user creation, refer to "3.3.2 Operation Procedure".
3.3.2 Operation Procedure
To create a Solaris operating system user account, perform the following operations on the Server:
1) Log in as root. 2) Execute the following command to run the system administration tool:
# admintool
3) In the dialog box [Admintool: Users], select the menu [Edit/Add]. 4) In the dialog box [Admintool: Add User], set the new user properties, and then click
<OK> to close the dialog box.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-4
3.4 Modifying Password of Operating System User
3.4.1 Operation Effect
It is necessary to stop the M2000 services to modify user password of "ftpuser". The modification of passwords of "root", "dbuser", "omcuser" and other users will not affect the running of M2000.
3.4.2 Modifying Password of root
1) Log in as root. 2) Execute the following command to modify the password of "root":
# passwd root
New password:
Re-enter new password:
passwd (SYSTEM): passwd successfully changed for root
3.4.3 Modifying Password of dbuser
1) Log in as root. 2) Execute the following command to modify the password of "dbuser":
# passwd dbuser
New password:
Re-enter new password:
passwd (SYSTEM): passwd successfully changed for dbuser
3.4.4 Modifying Password of omcuser
1) Log in as root. 2) Execute the following command to modify the password of "omcuser"
# passwd omcuser
New password:
Re-enter new password:
passwd (SYSTEM): passwd successfully changed for omcuser
3.4.5 Modifying Password of ftpuser
1) Log in as root. 2) Execute the following command to modify the password of "ftpuser":
# passwd ftpuser
New password:
Re-enter new password:
passwd (SYSTEM): passwd successfully changed for ftpuser
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-5
3) Execute the following command to stop the M2000 services.
# stop_svc
4) Run the M2000 parameter modification tool:
# /opt/OMC/imap_setup.sh
5) In the dialog box shown in Figure 3-1, select "Remote control parameters" to modify the password of ftpuser.
Figure 3-1 M2000 parameter setting
6) Execute the following command to start M2000 services.
# start_svc
3.5 Modifying Password of Database User
3.5.1 Operation Effect
It is necessary to stop M2000 services to modify the password of the user sa.
3.5.2 Operation Procedure
1) Log in as root.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-6
2) Execute the following command to stop M2000 services.
# stop_svc
3) Execute the following command to modify the password of Sybase user "sa":
# isql –SSYB -Usa –P<old password>
1>sp_password <old password >, <new password>
2>go
4) Run the M2000 parameter modification tool:
# /opt/OMC/imap_setup.sh
5) In the dialog box shown in Figure 3-1, select "Database parameters" to modify the password of "sa".
6) Execute the following command to start M2000 services.
# start_svc
3.6 Creating M2000 User Group
3.6.1 Operation Effect
After the creation of M2000 user group, the M2000 system will record all information of this user group.
3.6.2 Operation Procedure
Carry out the operations on M2000 Client. For details, refer to iManager M2000 Mobile Element Management System Operation Manual.
3.7 Creating M2000 User Account
3.7.1 Operation Effect
After the creation of M2000 user account, the M2000 system will record all information of this user.
3.7.2 Operation Procedure
Carry out the operations on M2000 Client. For details, refer to iManager M2000 Mobile Element Management System Operation Manual.
3.8 Monitoring M2000 Users
3.8.1 Operation Effect
The operation of M2000 user monitoring uses few system resources and has no effect on the system.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 3 User Management
3-7
3.8.2 Operation Procedure
Carry out the operations on M2000 Client. For details, refer to iManager M2000 Mobile Element Management System Operation Manual.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 4 Log Management
4-1
Chapter 4 Log Management
4.1 Overview of Log Management This chapter introduces the concepts related to log management, including log types and their corresponding contents, and provides the details of log management tasks, including:
Browsing user log Browsing system log Checking Solaris error log
4.2 Introduction to Log
4.2.1 Types of Logs
M2000 system provides four types of logs:
User log NE log System log trace log
4.2.2 User Log
I. Function
The user log records the operations of M2000 users. M2000 system administrator and operators can query the user log.
II. Path
The user log is stored in the database in M2000 Server. Its information can be queried and dumped through Client.
III. Contents
The information in user log includes operation contents, user name, operation start/end time, user type, terminal, operation objective and result.
4.2.3 NE Log
I. Function
The NE log records the operations on managed NEs. M2000 system administrator and operators can query the NE log.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 4 Log Management
4-2
II. Path
The NE log is generated on NEs, and then sent to M2000 Server and stored in the database in M2000 Server. Its information can be queried through Client.
III. Contents
The information in NE log includes user name, terminal, operation start/end time, operation contents and operation result, NE type and name.
4.2.4 System Log
I. Function
The system log records the operation of the system. M2000 system administrator can query system log.
II. Path
The system log is stored in "/export/home/omc/var/logs" in M2000 Server. The file names are iMAP.root.log, iMAP.root.log.1 and iMAP.root.log.2.
The system log information is written into iMAP.root.log.1 and iMAP.root.log.2 in cycle and normally not into iMAP.root.log.
The system log information can be queried through Client.
III. Contents
The contents of the system log include information header and information. The information header includes level, module identification and record time.
4.2.5 Trace log
I. Function
The trace log is used to locate the system internal problems.
II. Path
The trace log is stored in "/export/home/omc/var/logs" in M2000 Server. The file names are iMAP.root.trace, iMAP.root.trace.1 and iMAP.root.trace.xxx.tar.gz.
iMAP.root.trace and iMAP.root.trace.1 are used to save the current trace information. When one trace file is full, it will be converted to /export/home/omc/var/logs/traceback/iMAP.root.trace.xxx.tar.gz. The information will then be written in the other trace file. When the other file is full, again it is converted to iMAP.root.trace.xxx.tar.gz. The information is then written into the previous file. In this way, the trace information is updated into these two files alternatively.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 4 Log Management
4-3
III. Contents
The contents of trace log consist of information header and information. The information header includes level, module identification, service proxy identification (process name), record time and process thread ID.
4.3 Browsing User Log
4.3.1 Operation Effect
The operation of browsing user log uses few system resources and will not affect the system.
4.3.2 Operation Procedure
Carry out the operations on M2000 Client. For details, refer to iManager M2000 Mobile Element Management System Operation Manual.
4.4 Browsing System Log
4.4.1 Operation Effect
The operation of browsing system log uses few system resources and will not affect the system.
4.4.2 Operation Procedure
To browse system log, perform the following operations:
1) Log in to the Client. 2) In the main window, select the menu [System/Log/Log Manager]. 3) In the dialog box [Log Manager], select "System Log" in the navigation tree, and
the click <Query> in the right window. 4) Check whether any error information exists.
4.5 Checking Solaris Error Log
4.5.1 Operation Effect
The operation of browsing Solaris error log uses few system resources and will not affect the system.
4.5.2 Operation Procedure
To check the Solaris error log, perform the following operations on the Server:
1) Log in as omcuser. 2) Open the file "/var/adm/messages".
Administrator Guide iManager M2000 Mobile Element Management System Chapter 4 Log Management
4-4
3) Check whether this file contains any error information. Normally, there is no error information.
4) Open the file "/var/log/syslog". 5) Check whether this file contains any error information. Normally, there is no error
information.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 5 Server Performance Monitor
5-1
Chapter 5 Server Performance Monitor
5.1 Overview of Server Performance Monitor This chapter provides the details of Server performance monitor tasks, including:
Querying Server status through Client Setting Server status alarm threshold Querying system performance Adjusting system performance
5.2 Querying Server Status through Client
5.2.1 Function
It is possible to query M2000 Server status through M2000 Client, including:
System performance Hard Disk Database Service
5.2.2 Operation Procedure
To query Server status, perform the following operations:
1) Log in to the Client. 2) In the main window, select the menu [Tools/System Monitor/Monitor Browser]. 3) In the dialog box [System Monitor Browser], select the item to be queried, as
shown in Figure 5-1.
Figure 5-1 System monitor Browser
Administrator Guide iManager M2000 Mobile Element Management System Chapter 5 Server Performance Monitor
5-2
5.3 Setting the Threshold of Server Status Alarm
5.3.1 Function
It is possible to set the threshold of M2000 Server status alarm through M2000 Client, including:
CPU occupancy Memory occupancy Hard Disk space occupancy Database space occupancy
When an item reaches its threshold, the system will generate the corresponding alarm.
5.3.2 Operation Procedure
To set Server status alarm threshold, perform the following operations:
1) Log in to the Client. 2) In the main window, select the menu [Tools/System Monitor/Configurations]. 3) In the dialog box [System Monitor Configurations], select the item to be set, as
shown in Figure 5-2.
Figure 5-2 System monitor configurations
5.4 Querying System Performance
5.4.1 Operation Effect
The operation of querying system performance uses few system resources and will not affect the system.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 5 Server Performance Monitor
5-3
5.4.2 Operation Procedure
Besides querying through Client in the way introduced in 5.2 Querying Server Status through Client, you can also perform the following operations on M2000 Server:
1) Log in as omcuser. 2) Execute the following command:
bash-2.03$ vmstat 1 10
procs memory page disk faults cpu
r b w swap free re mf pi po fr de sr s0 s6 -- -- in sy cs us sy
id
0 0 0 5114824 1032584 24 95 8 1 1 0 0 9 0 0 0 543 87 692 17 6
76
0 0 0 4884768 891800 43 264 0 0 0 0 0 0 0 0 0 536 30913 1046 50 19
31
0 0 0 4885104 892136 0 1 0 0 0 0 0 0 0 0 0 546 30019 910 53 16
31
0 0 0 4885104 892136 0 0 0 0 0 0 0 0 0 0 0 609 30131 1119 54 14
32
0 0 0 4883552 890936 98 747 168 8 8 0 0 25 0 0 0 739 33041 1263 54 20
26
0 0 0 4883888 891272 0 1 0 0 0 0 0 0 0 0 0 532 31216 892 50 17
33
0 0 0 4883888 891272 0 0 0 0 0 0 0 0 0 0 0 506 30112 963 52 15
33
0 0 0 4883552 890936 43 258 0 0 0 0 0 0 0 0 0 890 31651 1787 57 13
29
0 0 0 4883888 891272 0 1 0 0 0 0 0 0 0 0 0 541 30023 1063 53 16
31
0 0 0 4883760 890640 289 1651 192 0 0 0 0 26 0 0 0 869 32775 1106 56 22
22
In the output, “us” is the percentage usage of CPU time of user process, “sy” is the percentage usage of CPU time of system process and “id” is the percentage idle of CPU time.
3) Check the system performance. Normally the CPU occupancy must be lower than 80%. That is, the value of “id” must be higher than 20.
5.5 Adjusting System Performance
5.5.1 Operation Effect
If the adjustment is improper, the system operation may become abnormal.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 5 Server Performance Monitor
5-4
5.5.2 Operation Procedure
If the CPU occupancy is too high (higher than 80%), perform the following operations:
1) Check whether the high CPU occupancy is caused by number of reported alarms exceeding the threshold.
2) Execute the following command to check the CPU occupancy of each process.
bash-2.03$ top
load averages: 0.07, 0.09, 0.10 11:30:4
95 processes: 94 sleeping, 1 on cpu
CPU states: 97.4% idle, 1.5% user, 1.1% kernel, 0.0% iowait, 0.0% swap
Memory: 2048M real, 211M free, 2743M swap in use, 2821M swap free
PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND
13529 root 60 58 0 75M 56M sleep 160:11 0.91% imapsvcd
357 root 180 58 0 75M 66M sleep 916:19 0.72% dataserver
345 root 72 58 0 73M 65M sleep 639:50 0.49% dataserver
13524 root 27 48 0 60M 32M sleep 112:23 0.42% imapsysd
13761 root 37 58 0 155M 115M sleep 60:03 0.24% imapsvcd
13531 root 25 58 0 96M 69M sleep 69:42 0.16% imapsvcd
10904 root 128 58 0 321M 223M sleep 9:19 0.16% imapsvcd
13871 root 14 58 0 285M 188M sleep 10:10 0.14% imapsvcd
45 root 1 58 0 2072K 1360K cpu/1 0:00 0.12% top
13527 root 14 58 0 96M 66M sleep 5:24 0.07% imapsvcd
13540 root 11 58 0 99M 66M sleep 6:34 0.05% imapsvcd
13591 root 30 58 0 322M 236M sleep 32:56 0.05% imapsvcd
13520 root 27 58 0 58M 27M sleep 8:22 0.02% Monitor_Service
6 root 1 0 0 352K 248K sleep 0:00 0.02% sh
13511 root 56 58 0 25M 22M sleep 0:29 0.01% Naming_Service
3) Check whether the value of database memory parameter is too small. It is recommended that the value of "set shmsys:shminfo_shmmax" in the file "/etc/system" be the size of the Server memory (unit: MB) × 1024 × 1024 / 2.
For example, if the memory of the Server is 4096MB, then:
set shmsys:shminfo_shmmax=2,147,483,648
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-1
Chapter 6 M2000 Process and Service Management
6.1 Overview of M2000 Process and Service Management This chapter introduces the concepts related to M2000 services and processes, including types and functions of the processes and services, and provides the details of the major process and service management tasks, including:
Querying number of M2000 processes Querying service status Starting M2000 services Stopping M2000 services
6.2 Introduction to M2000 Processes and Services
6.2.1 Overview to Processes and Services
When M2000 is running normally, the Server starts 18 processes. Each process includes different services and provides different functions. The following section introduces the function of each processes and services.
6.2.2 SystemConfigurator
SystemConfigurator manages all other local processes. In a distributed environment, it communicates and interacts with imapsysd processe on other machines, so as to avoid the impact on application processes caused by the distributed system.
When M2000 services are running, this process cannot be stopped.
Dependent service: None.
6.2.3 sac_agent
The process sac_agent provides the following services:
ScheduleService
ScheduleService provides a frame construction, which enables the scheduling and control of user tasks.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
BackupService
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-2
BackupService backs up important configuration files, databases and managed object (MO) instance data of the system periodically.
When there is no backup task, this service can be stopped.
Dependent service: None.
LicenseService
LicenseService provides a service interface for checking the validity of license file of the current version.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
LogService
LogService records system log. It receives the system logs from other processes through a socket, and then manages and stores the system logs.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
6.2.4 em_agent
The process em_agent provides the service EventService.
EventService provides a message transmission mechanism between imap services and between imap and iview. It also provides the function of message broadcast and filter.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
6.2.5 monitor_agent
The process monitor _agent provides the following services:
MonitorService
MonitorService monitors the system running status, including CPU and memory occupancy, free disk space and database system running status.
When M2000 services are running, this service cannot be stopped.
Dependent service: EventService.
FlowController
FlowController accepts the operation requests from other modules. These requests are mainly those requiring large amount of resources. It decides whether to block a request according to the current CPU and memory utilization.
When M2000 services are running, this service cannot be stopped.
Dependent service: EventService and MonitorService.
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-3
6.2.6 partition_agent
The process partition_agent provides the service PartitionService.
PartitionService divides the management objects into partitions. Different partitions are managed by different processes. These processes can be deployed in different servers. In this way, even when the number of management objects is large, the load can be balanced.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
6.2.7 audit_agent
The process audit-agent provides the service AuditService.
AuditService records the operation information in database, supports operation information query and log statistics information query on the Client, and provides periodic or manual displacing.
When M2000 services are running, this service cannot be stopped.
Dependent service: ScheduleService.
6.2.8 mo_agent
The process mo_agent provides the following services:
LockService
LockService provides lock management when other services are creating, deleting, querying and modifying management objects to ensure the consistency and completeness of the operations from multiple services to the same management objects.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
RelationService
RelationService creates, queries and deletes the relations between management objects and saves these relations into database.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
MOService
MOService loads and verifies the types of all managed objects in M2000 system, loads managed object dynamic base, creates managed object cases and solidifies the managed object.
When M2000 services are running, this service cannot be stopped.
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-4
Dependent service: LockService, RelationService, EventService and PartitionService.
6.2.9 sm_agent
The process sm_agent provides the service SecurityService.
SecurityService controls the access to the sensitive resources in the Element Management System (EMS), so that only those authorized users can access to these resources. It realizes the access control by restricting the users' authority to use various interfaces.
When M2000 services are running, this service cannot be stopped.
Dependent service: EventService, MonitorService, AuditService and MOService.
6.2.10 med_agent
The process med_agent provides the service MediationService.
MediationService creates, deletes and retrieves various NE engines mapped to network equipment in M2000 system and manages the relevant event intercepter. The NE engines realize the communication between M2000 system and various network equipments.
When M2000 services are running, this service cannot be stopped.
Dependent service: MOService.
6.2.11 ts_agent
The process ts_agent provides the service TopoService.
TopoService maintains the relations between the objects in the subnet, creates and deletes the subnet, node, sub-node and link.
When M2000 services are running, this service cannot be stopped.
Dependent service: SecurityService.
6.2.12 ifms_agent
The process ifms_agent provides the service FaultService.
FaultService collects, analyzes, handles, stores and displays the faults reported by equipment.
This service can be stopped when the fault management function is not in use.
Dependent service: EventService, MOService, SecurityService and TopoService.
6.2.13 manager_agent
The process manager_agent provides the service SystemService.
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-5
SystemService provides the function of querying M2000 version information, including operating system version, Client software version, Server software version query and the corresponding Client software version, and Client upgrade information.
When M2000 services are running, this service cannot be stopped.
Dependent service: None.
6.2.14 pm_agent
The process pm_agent provides the service PMService.
PMService realizes the performance services of all NEs. It is entirely independent of individual NE, MO and the interaction with Hosts.
When M2000 services are running, this service cannot be stopped.
Dependent service: EventService, MOService, SecurityService and AuditService.
6.2.15 cmserver_agent
The process cmserver_agent provides the service CMServer.
CMServer realizes the configuration service of all NEs, and is entirely independent of individual NE, MO and the interaction with Hosts.
When M2000 services are running, this service cannot be stopped.
Dependent service: ventService, MOService, SecurityService, TopoService and AuditService.
6.2.16 swm_agent
The process swm_agent provides the service SWMService.
SWMService manages the versions, configuration data and other files of all NEs. It provides download, upload, activation and rollback functions.
When M2000 services are running, this service cannot be stopped. Dependent service: EventService, MOService, SecurityService and AuditService.
This service can be stopped when the software management function is not needed.
Dependent service: EventService, MOService, SecurityService and AuditService.
6.2.17 fmnotify_agent
The process fmnotify_agent provides the service FMNotify.
FMNotify forwards the fault information from FaultManager to Network Management System (NMS).
This service can be stopped when realtime alarm forwarding is not needed.
Dependent service: EventService and FaultService.
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-6
6.2.18 proxy_agent
The process proxy_agent provides the service ProxyServer.
ProxyServer enables M2000 Client to access NEs through a proxy server to run the LMT programs of these NEs.
This service can be stopped when proxy of BTS maintenance is not needed.
Dependent service: EventService.
6.2.19 notify_agent
The process notify_agent provides the service RemoteNotifyService.
RemoteNotifyService realizes the remote notification of alarms.
This service can be stopped when remote alarm notification is not needed.
Dependent service: EventService, MOService, SecurityService, TopoService and FaultService.
6.3 Querying Number of M2000 Processes
6.3.1 Operation Effect
The operation of querying number of M2000 processes uses few system resources and will not affect the system.
6.3.2 Operation Procedure
To query the number of M2000 processes, perform the following operations on the Server:
1) Log in as omcuser. 2) Execute the following command:
bash-2.03$ svc_ps | wc –l
18
6.4 Querying Service Status
6.4.1 Operation Effect
The operation of querying service status uses few system resources and will not affect the system.
6.4.2 Operation Procedure
You can query on Client according to 5.2 Querying Server Status through Client, or query on M2000 Server by performing the following operations:
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-7
1) Log in as omcuser. 2) Execute the following command:
bash-2.03$ svc_adm –cmd status
Number of hosts: 1
Host: DEFAULTSYSAGENT
SystemConfigurator: running
Service Agent: sac_agent [4 service(s)] pid: 427
ScheduleManager [running ]
SysBackupMgr [running ]
LicenseMgr [running ]
LogServer [running ]
Service Agent: em_agent [1 service(s)] pid: 429
EventManager [running ]
Service Agent: monitor_agent [1 service(s)] pid: 431
SystemMonitor [running ]
Service Agent: partition_agent [1 service(s)] pid: 445
PartitionManager [running ]
Service Agent: audit_agent [1 service(s)] pid: 451
AuditServer [running ]
Service Agent: mo_agent [3 service(s)] pid: 457
LockManager [running ]
RelationManager [running ]
MOManager [running ]
Service Agent: sm_agent [1 service(s)] pid: 595
SecurityController [running ]
Service Agent: med_agent [1 service(s)] pid: 623
MediationController [running ]
Service Agent: ts_agent [1 service(s)] pid: 613
TSService [running ]
Service Agent: ifms_agent [1 service(s)] pid: 904
FaultManager [running ]
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-8
Service Agent: manager_agent [1 service(s)] pid: 439
SystemManager [running ]
Service Agent: pm_agent [1 service(s)] pid: 990
PMService [running ]
Service Agent: cmserver_agent [1 service(s)] pid: 1036
CMServer [running ]
Service Agent: swm_agent [1 service(s)] pid: 1106
SWMService [running ]
Service Agent: fmnotify_agent [1 service(s)] pid: 1076
FMNotify [running ]
Service Agent: proxy_agent [1 service(s)] pid: 1137
ProxyServer [running ]
Service Agent: notify_agent [1 service(s)] pid: 934
NotifyManager [running ]
6.5 Starting M2000 Services
6.5.1 Operation Effect
The execution of this command starts all M2000 services. Those already started will not be affected.
6.5.2 Operation Procedure
To start M2000 services, perform the following operations on the Server:
1) Log in as root. 2) Execute the following command:
# start_svc
Note:
Before starting M2000 Server, make sure that Sybase service has been started normally. For information about starting Sybase service, refer to "17.10 Starting Sybase".
Administrator Guide iManager M2000 Mobile Element Management System
Chapter 6 M2000 Process and Service Management
6-9
6.6 Stopping M2000 Services
6.6.1 Operation Effect
After executing the command, all M2000 services will be stopped. When the M2000 services are stopped, the performance data and alarm data of the NEs may be lost.
6.6.2 Operation Procedure
To stop M2000 services, perform the following operations on the Server:
1) Log in as root. 2) Execute the following command:
# stop_svc
If there is any service still running, execute the following command to stop it:
# kill_svc
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-1
Chapter 7 Database Management
7.1 Overview of Database Management This chapter introduces the concepts related to M2000 database, including types and contents of the databases, and provides the details of major database management tasks, including:
Querying database status Manually displacing alarm data Manually displacing user log Setting auto displacing for alarm data Setting auto displacing for user log Deleting performance task Clearing database
7.2 Introduction to Database
7.2.1 Overview of Database
On the basis of Sybase database, M2000 has four databases:
omcdb fmdb pmdb sysmdb
After the installation of M2000 Server applications, the sizes of the databases are decided, and do not need manual modification.
You can use Sybase commands to manage the databases.
7.2.2 omcdb
The database omcdb is used to store the M2000 configuration data, security data and the data related to internal realization. It needs at least 1000MB of free space.
The tables in omcdb and their contents are shown in Table 7-1.
Table 7-1 Database table name and contents of omcdb
Name Content
SMLoginRec User login information.
SMNEUser NE user information.
SMSecurityPolic Security strategy.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-2
Name Content
SMTerminal Terminal information.
SMUser User information.
SMUserGroup User group information.
tbl_AccessTable Save and read authority.
tbl_AuditTable Operation log information.
Other tables Information of configuration, security and other internal realization.
7.2.3 fmdb
The database fmdb is used to store the alarm data of the NEs and M2000. It needs at least 3700MB of free space.
The tables in fmdb and their contents are as are shown in Table 7-2.
Table 7-2 Database table name and contents of fmdb
Name Content
tbl_cur_alm Current alarms.
tbl_event Event alarms.
tbl_his_alm History alarms.
tbl_mask_alm Screened alarms.
Other tables Information about internal realization of alarm handling.
7.2.4 pmdb
I. Overview of pmdb
The database pmdb is used to store the performance measurement data of NEs. It needs at least 13000MB of free space.
The table types in pmdb are as follows:
Counter information tables Task information tables Task result tables
II. Counter information tables
The counter information tables store a group of relatively fixed information. The tables and their contents are shown in Table 7-3.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-3
Table 7-3 Database table name and contents of pmdb (counter information tables)
Name Content
systbl_NeType All NE types that can be managed by M2000.
systbl_FuncSet Function sets of all NEs.
systbl_FuncSubSet Measurement units of all function sets.
systbl_Counters Measurement items of all measurement units.
systbl_Counter_Unit Units of various measurement items.
III. Task information tables
The task information tables store the information related to task registration. The tables and their contents are shown in Table 7-4.
Table 7-4 Database table name and contents of pmdb (task information tables)
Name Content
tbl_JobGeneralInfo Basic task information. Each record stands for a task.
tbl_JobObject Object information corresponding to tasks.
tbl_JobCounter Measurement item information corresponding to tasks.
IV. Task result tables
The task result tables store the information related to task result. The tables and their contents are shown in Table 7-5.
Table 7-5 Database table name and contents of pmdb (task result tables)
Name Content
tbl_jobrst_* Task result. Each task corresponds to a task result table.
tbl_LostResultInfo Task loss information. If the task result of a NE cannot be received within a certain period of time, a record will be added to this table.
tbl_JobSuspendInfo Information of suspended task.
7.2.5 sysmdb
The database sysmdb is used to store the file information and NE version configuration data managed by the software management module. It needs at least 3000MB of free space.
The tables in sysmdb and their contents are shown in Table 7-6.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-4
Table 7-6 Database table name and contents of sysmdb
Name Content
tbl_FTPFileSet File information managed by software management module.
tbl_VersionRelation Information of version file matching.
log Information of internal realization.
sys_log_del Auto-clearing conditions of logs.
tbl_UnsendMMLCmd Commands to be sent to the disconnected NEs once the connection recovers.
tbl_NELogTable NE operation logs
7.3 Querying Database Status
7.3.1 Operation Effect
The operation of querying database status uses few system resources and will not affect the system.
7.3.2 Operation Procedure
You can query on Client according to 5.2 Querying Server Status through Client, or query on M2000 Server by performing the following operations:
1) Log in as omcuser. 2) Execute the following command to view all databases:
bash-2.03$ isql –SSYB –Usa –P <user sa password>
1> sp_helpdb
2> go
3) Execute the following command to view the data space and transaction log space in each database:
1> sp_helpdb fmdb
2> go
1> sp_helpdb pmdb
2> go
1> sp_helpdb omcdb
2> go
1> sp_helpdb sysmdb
2> go
1> exit
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-5
7.4 Manually Displacing Alarm Data
7.4.1 Operation Effect
After displacing, the alarm data in fmdb will be saved as files to the default displacing path in the Server. User can decide whether to delete the original data from the database.
7.4.2 Operation Procedure
To manually dump the alarm data, perform the following operations:
1) Log in to the Client. 2) In the main interface M2000 Client, select the menu [Fault/Alarm Displace] to open
the window [Alarm Displace], as shown in Figure 7-1.
Figure 7-1 Alarm displace
3) Select the tab "Manual Displace". 4) Specify the parameters such as the alarm types to be dumped, and then click
<Start>.
7.5 Manually Displacing User Log
7.5.1 Operation Effect
After displacing operation, the log data in omcdb will be saved as files to the default displacing path in the Server and the dumped logs will be deleted from the database.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-6
7.5.2 Operation Procedure
To manually dump the logs, perform the following operations:
1) Log in to the Client. 2) In the main interface of M2000 Client, select the menu [System/Log/User Log
Settings] to open the window [User Log Set], as shown in Figure 7-2.
Figure 7-2 Log displace
3) Select the tab "Manual Displace". 4) Specify whether to dump by time or by quantity of log information, and then click
<Displace>.
7.6 Setting Auto Displacing for Alarm Data
7.6.1 Operation Effect
After auto displacing, the alarm data in fmdb will be saved as files to the default path in the Server, and the dumped data will be deleted from the database.
7.6.2 Operation Procedure
To set auto displacing for alarm data, perform the following operations:
1) Log in to the Client. 2) In the main interface of M2000 Client, select the menu [Fault/Alarm Displace] to
open the window [Alarm Displace], as shown in Figure 7-1. 3) Select the tab "Auto Displace".
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-7
4) Specify the parameters such as the type of alarm to be dumped, and then click <Set>.
7.7 Setting Auto Displacing for User Log
7.7.1 Operation Effect
After auto displacing, the user log data in omcdb will be saved as files to the default path in the Server, and the dumped data will be deleted from the database.
7.7.2 Operation Procedure
To set auto displacing for user log data, perform the following operations:
1) Log in to the Client. 2) In the main interface of M2000 Client, select the menu [System/Log/Settings] to
open the window [Log Setting], as shown in Figure 7-2. 3) Select the tab "Overflow Displace". Specify the displacing condition, and then click
<Set> to realize auto displacing on overflow. 4) Select the tab "Periodic Displace". Specify the displacing condition, and then click
<Set> to realize periodic auto displacing.
7.8 Deleting Performance Task
7.8.1 Operation Effect
The performance task data cannot be dumped directly, but the performance task results can be saved as files and then the tasks can be deleted to clear pmdb.
After deleting a performance task, all information related to this task will be deleted from the database.
7.8.2 Operation Procedure
To delete a performance task, perform the following operations:
1) Log in to the Client. 2) In the main interface of M2000 Client, select the menu [Performance/Show Job
List] to open the window [Performance Job List]. 3) Right-click the task to be deleted, and then select the menu [Job/Delete] in the
shortcut menu. 4) Confirm the deletion.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 7 Database Management
7-8
7.9 Clearing Database
7.9.1 Operation Effect
Clearing the data space of database has no effect on the running of the system. Clearing the transaction log space of database will affect the system backup function. It causes incomplete backup.
7.9.2 Operation Procedure
Perform the following operations to clear the data space and transaction log space in database according to the query result of database space (refer to "7.3 Querying Database Status"):
1) Dump the alarm data, and clear data space in fmdb. Refer to "7.4 Manually Displacing Alarm Data" and "7.6 Setting Auto Displacing for Alarm Data".
2) Dump the user log data, and clear data space in omcdb. Refer to "7.5 Manually Displacing User Log" and "7.7 Setting Auto Displacing for User Log"
3) Delete the performance task to clear data space in pmdb. Refer to "7.8 Deleting Performance".
4) Execute the following commands to clear the transaction data log space:
Caution:
Clearing transaction log will affect the backup function of the system.
bash-2.03$ isql –SSYB –Usa –P<user sa password>
1> dump tran fmdb with no_log
2> go
1> dump tran omcdb with no_log
2> go
1> dump tran pmdb with no_log
2> go
1> dump tran sysmdb with no_log
2> go
1> exit
Administrator Guide iManager M2000 Mobile Element Management System Chapter 8 Disk Space Management
8-1
Chapter 8 Disk Space Management
8.1 Overview of Disk Space Management This chapter introduces the concepts related to M2000 file system, and provides the details of disk space management tasks, including:
Querying disk space Clearing disk space
8.2 Introduction to File System
8.2.1 Overview of System Structure
The system structure of M2000 is server/client mode.
The Server realizes the communication with the NEs, stores the operation and maintenance data of NEs and provides NMS-oriented interface.
The Client provides graphic user interface to realize the operation and maintenance to NEs and the status monitor to M2000.
8.2.2 Server File System
The M2000 Server software runs on Solaris. It is constructed on the basis of the following software:
Sybase database CORBA functional software FTP functional software
The installation package of M2000 Server software includes the software provides the FTP function and CORBA (Common Object Request Broker Architecture) function.
Table 8-1 lists the directory structure of M2000 Server software.
Table 8-1 Directory structure of M2000 Server software
Directory Description
$M2K_ROOT Installation directory of M2000. Default: /opt/OMC
$M2K_ROOT/bin Directory storing executable files.
$M2K_ROOT/etc Directory storing system configuration files and SQL scripts.
$M2K_ROOT/idl_northbound Directory storing northbound IDL interface files.
$M2K_ROOT/lib Directory storing library files.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 8 Disk Space Management
8-2
Directory Description
$M2K_ROOT/lbin Directory storing system management commands.
$M2K_ROOT/model Directory storing managed object XML model files.
$M2K_ROOT/3rdTools Directory storing third-party software.
/export/home/omc/var Directory storing M2000 running data.
/export/home/omc/var/logs Directory storing system logs.
/export/home/backup Directory storing backup files.
8.2.3 Client File System
The Client software runs on Windows. It is constructed on the basis of JAVA virtual machine. The installation package of M2000 Client software includes JAVA virtual machine for Windows.
Table 8-2 lists the directory structure of M2000 Client software.
Table 8-2 Directory structure of M2000 Client software
Directory Description
<M2000 install directory> Installation directory of M2000. Default: C:\ iManagerM2000Client
<M2000 install directory>\bin Directory storing executable files
<M2000 install directory>\Data Directory storing NE configuration files
<M2000 install directory>\dtd Directory storing "dtd" files used to analyze "xml" files
<M2000 install directory>\help Directory storing online help
<M2000 install directory>\jre Directory storing java runtime
<M2000 install directory>\lib Directory storing operation base files
<M2000 install directory>\openorb Directory storing openorb third-party base
<M2000 install directory>\style Directory storing configuration files
<M2000 install directory>\tracefile Directory storing trace files
<M2000 install directory>\UninstallerData Directory storing uninstall executable files
<M2000 install directory>\update Directory storing upgrade base files
8.3 Query Disk Space
8.3.1 Operation Effect
Querying disk space uses few system resources, and will not affect the system.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 8 Disk Space Management
8-3
8.3.2 Operation Procedure
You can query on M2000 Client according to 5.2 Querying Server Status through Client, or query on M2000 Server by performing the following operations:
1) Log in as omcuser. 2) Execute the following command:
bash-2.03$ df –k
3) Check the usage of disk space. Normally the usage of disk space must be lower than 80%. That is, the output value of “capacity” must be lower than 80.
8.4 Clearing Disk Space
8.4.1 Operation Effect
Do not delete any file of the operating system. If any file of the operating system is deleted, the system cannot operate.
8.4.2 Operation Procedure
To clear the disk space, perform the following operations on the Server:
1) Log in as root. 2) Execute the following command to search for the core files:
bash-2.03$ find / -name “core*” –ls
3) Delete the useless core files. 4) Delete all files in "/var/tmp" under that directory. 5) Delete other useless files.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 9 Dual-Plane Configuration
9-1
Chapter 9 Dual-Plane Configuration
9.1 Overview of Dual-Plane Configuration This chapter introduces the concepts related to dual-plane, and provides the details of dual-plane configuration tasks, including:
Planning IP data Manually setting dual-plane Automatically setting dual-plane Verifying dual-plane settings
9.2 Introduction to Dual-Plane Dual-plane means that Solaris OS dynamically monitors dual network adapters of a single computer, and automatically switch the IP address of the faulty network adapter to the normal one. In this way, continuous communications are insured. In addition, Solaris OS goes on monitoring the faulty network card, and restores the original IP address and mask if it becomes valid again.
As shown in Figure 9-1, the Server has two Ethernet adapters: hme0 and hme1.These two adapters are connected with the management network. Each adapter has an IP. They belong to the same IP group.
ManagementNetwork
Server
hme0 hme1Client
Figure 9-1 Dual-plane networking
Caution
The names of the Ethernet adapters are not necessarily hme0 and hme1.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 9 Dual-Plane Configuration
9-2
9.3 Configuration Procedure of Dual-Plane The configuration procedure of dual-plane is as follows:
1) Planning IP data 2) Manually or automatically setting the dual-plane 3) Verifying the settings of dual-plane
9.4 Planning IP Data The following information needs to be planned:
IPs and subnet masks of the two Ethernet adapters Two test IPs and their subnet masks IP group name
For example, for Figure 9-1 the planning information is:
hme0: IP: 10.10.105.22, subnet mask: 255.255.255.0. The test IP of this adapter: 10.10.105.66, subnet mask: 255.255.255.0
hme1: IP: 10.10.105.23, subnet mask: 255.255.255.0. The test IP of this adapter: 10.10.105.68, subnet mask: 255.255.255.0
IP group name: imap
9.5 Manually Setting Dual-Plane
9.5.1 Operation Effect
Manual setting is carried out through commands. The results are stored in the memory. If the Server is restarted, all setting information will be lost. Therefore, manual setting is normally used to test the correctness of dual-plane configuration. In practice, automatic setting is recommended.
In this mode, the Server provides two external IPs. You can select either one for the application.
9.5.2 Operation Procedure
To manually set the two adapters, perform the following operations:
1) Execute the following commands to set the adapters:
# ifconfig hme0 unplumb
# ifconfig hme1 unplumb
# ifconfig hme0 plumb
# ifconfig hme1 plumb
2) Execute the following commands to add the adapters to the group:
# ifconfig hme0 group imap
Administrator Guide iManager M2000 Mobile Element Management System Chapter 9 Dual-Plane Configuration
9-3
# ifocnfig hme1 group imap
3) Execute the following commands to set the IP of the adapters, disable their failover and add deprecated flag.
# ifconfig hme0 10.10.105.22 netmask 255.255.255.0 up
# ifconfig hme1 10.10.105.23 netmask 255.255.255.0 up
# ifconfig hme0 addif 10.10.105.66 netmask 255.255.255.0 -failover deprecated up
# ifconfig hme1 addif 10.10.105.68 netmask 255.255.255.0 -failover deprecated up
Dual-plane is complete.
9.6 Automatically Setting Dual-Plane
9.6.1 Operation Effect
Automatic setting is realized by writing the commands into the operating system files. When the operating system is started, the settings of dual-plane will take effect automatically.
This mode provides an external IP only, which is different from the manual mode. In the following example, the external IP is 10.10.105.22.
9.6.2 Operation Procedure
To carry out the automatic settings of the two Ethernet adapters, perform the following operations:
1) Open the file "/etc/hosts", and add the following contents:
10.10.105.22 imap-e4500
Note:
imap-e4500 is the host name.
2) Open the configuration file of the first Ethernet adapter "/etc/hostname.hme0", and add the following contents:
imap-e4500 group imap up
addif 10.10.105.66 netmask 255.255.255.0 -failover deprecated up
Caution:
In the files "/etc/hostname.hme0" and "/etc/hostname.hme1", there must be no space before each line.
3) Open the configuration file of the second Ethernet adapter "/etc/hostname.hme1", and add the following contents:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 9 Dual-Plane Configuration
9-4
10.10.105.68 netmask 255.255.255.0 group imap -failover deprecated up
4) Execute the following command to restart the system:
# init 6
After restarting the system, the dual-plane settings take effect.
9.7 Verifying Dual-Plane Settings
9.7.1 Operation Effect
The verification of dual-plane settings uses little system resource and will not affect the system.
9.7.2 Operation Procedure
Execute the following commands to verify the dual-plane settings:
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
hme0:flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 10.10.105.22 netmask ffffff00 broadcast 10.255.255.255
groupname imap
ether 8:0:20:8b:0:8d
hme0:1:flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAIL
OVER> mtu 1500 index 4
inet 10.10.105.66 netmask ffffff00 broadcast 10.255.255.255
ether 8:0:20:8b:0:8d
hme1:flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 10.10.105.23 netmask ffffff00 broadcast 10.255.255.255
groupname imap
ether 8:0:20:8b:0:8d
hme1:1:flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAIL
OVER> mtu 1500 index 5
inet 10.10.105.68 netmask ffffff00 broadcast 10.255.255.255
ether 8:0:20:8b:0:8d
The above information shows that the IPs of the two adapters are set as 10.10.105.22 and 10.10.105.23 respectively, and have been added to the group imap, and their test IPs are also correct.
9.7.3 Abnormal Handling
If the settings is not successful, perform the following operations:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 9 Dual-Plane Configuration
9-5
1) Check the file "/etc/hostname.hme*". There must be no space before the script in this file.
2) In the system startup information, check the parameter "local-mac-address" in Server openboot ROM. Its value must be true.
3) Set the dual-plane again.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 10 NTP Service Configuration
10-1
Chapter 10 NTP Service Configuration
10.1 Overview of NTP Service Configuration This chapter introduces the concepts related to Network Time Protocol (NTP) service, and provides the details of NTP service configuration tasks, including:
Setting M2000 as top NTP Server Setting M2000 as middle NTP Server Setting M2000 as NTP Client Starting NTP service Checking NTP service running status Stopping NTP service
10.2 Introduction to NTP Service NTP defines time synchronization mechanism. It synchronized the time between distributed time Server and Client. The theoretical precision reaches nanoseconds.
The M2000 Server uses Solaris system to support NTP. You can set M2000 as the NTP Server or Client by setting the Solaris parameters.
NTP serverLevel 0
NTP serverLevel 1
NTP serverLevel 2
NTP client
NTP serverLevel 1
NTP serverLevel 1
NTP serverLevel 2
NTP client
Figure 10-1 NTP synchronization networking
As shown in Figure 10-1, there are three types of computers:
Top NTP Server: Refer to level 0 NTP Server. It provides time synchronization service for next level.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 10 NTP Service Configuration
10-2
Middle NTP Server: Refer to level 1 Server and Level 2 Server. It retrieves time from higher level and provides time service for lower level.
NTP Client: It only retrieves time, and does not provide time service.
10.3 Setting M2000 as Top NTP Server Perform the following operations to set M2000 as the top NTP Server:
1) Log in to M2000 Server as root. 2) Execute the following command:
# cp /etc/inet/ntp.server /etc/inet/ntp.conf
# vi /etc/inet/ntp.conf
3) Set the values of all "XType"s in the file to "1". 4) Save the file "/etc/inet/ntp.conf" and quit vi.
10.4 Setting M2000 as Middle NTP Server Perform the following operations to set M2000 as the middle NTP Server:
1) Log in to M2000 Server as root. 2) Execute the following command:
# cp /etc/inet/ntp.server /etc/inet/ntp.conf
# vi /etc/inet/ntp.conf
3) Add a line "server XXX.XXX.XXX.XXX" before " server 127.127.1.0 prefer" to specify the IP of the higher level NTP Server.
4) Delete "stratum 0" from " fudge 127.127.Xtype.0 stratum 0". 5) Set the values of all "XType"s in the file to "1". 6) Save the file "/etc/inet/ntp.conf" and quit vi.
10.5 Setting M2000 as NTP Client Perform the following operations to set M2000 as the NTP Client:
1) Log in to M2000 Server as root. 2) Execute the following command:
# cp /etc/inet/ntp.client /etc/inet/ntp.conf
# vi /etc/inet/ntp.conf
3) Add a line "server XXX.XXX.XXX.XXX" to the file to specify the IP of the higher level NTP Server.
4) Save the file "/etc/inet/ntp.conf" and quit vi.
10.6 Starting NTP Service Perform the following operations to start NTP service:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 10 NTP Service Configuration
10-3
1) Log in to M2000 Server as root. 2) Check whether the time zone, data and time of the Server are correct. If they are
incorrect, it is necessary to modify them manually. Refer to "2.2 Modifying Server Time".
3) If the NTP service is already running, it is necessary to stop it first:
# /etc/init.d/xntpd stop
Note:
The startup script of NTP is in "/etc/rc2.d/". The NTP service will be automatically started after Solaris is started. Therefore, there is no need to add the auto startup script manually.
4) Start NTP service in the NTP Server. If M2000 is set as top or middle NTP Server, execute the following command:
# /etc/init.d/xntpd start
5) Start NTP service in the NTP Client. If M2000 is set as NTP Client, execute the following command:
# ntpdate <NTP Server IP>
# /etc/init.d/xntpd start
10.7 Checking Running Status of NTP Service Execute the following command to check the running status of NTP:
# ntpq –p
remote refid st t when poll reach delay offset jitter
==========================================================================
====
*LOCAL(0) .LCL. 0 l 10 64 377 0.000 0.000 0.000
224.0.1.1 0.0.0.0 16 - - 64 0 0.000 0.000 4000.00
In the returned information, if there is as "*" before "LOCAL(0)", it means that the status of this clock reference source is normal. "LOCAL(0)" means that the local clock is used as the reference clock source.
10.8 Stopping NTP Service Perform the following operations to stop the NTP service:
1) Log in to M2000 Server as root. 2) Execute the following command:
# /etc/init.d/xntpd stop
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-1
Chapter 11 Backup and Restoration
11.1 Overview of Backup and Restoration This chapter introduces the concepts related to backup and restoration, and provides the details of backup and restoration tasks, including:
Modifying configuration file Automatically backing up M2000 system Manually backing up M2000 system Restoring M2000 system Backing up operating system Restoring operating system
11.2 Introduction to Backup and Restoration
11.2.1 M2000 System Backup Contents
M2000 system backup means to back up the following contents:
The four databases of M2000: omcdb, fmdb, pmdb, sysmdb The system file of M2000: the files in "/export/home/omc/var" and
"/export/home/sysm"
After the execution of backup, the above files are packed into a file package.
After the execution of restoration, all the content in the file package will be restored. As for the data that hasn’t been packed in the file package because of being processed after backup is executed, M2000 can get it from NE by using auto synchronization function, and process it over again.
11.2.2 M2000 System Backup and NE Data Backup
M2000 provides system backup and NE data backup function.
NE data backup: With NE data backup function, the data on NEs, including NE configuration data and LICENSE, can be backed up to M2000 Server hard disks. For detailed information of NE data backup, refer to iManager M2000 Mobile Element Management System Operation Manual.
M2000 System Backup: With M2000 system backup function, the information on M2000 Server hard disks can be backed up to types.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-2
11.2.3 The Mode of M2000 System Backup and Restore
I. The Mode of M2000 System Backup
M2000 system backup mode can be classified as auto backup and manual backup. Auto backup is also referred as periodic backup.
M2000 system backup mode can also be classified as incremental backup and full backup.
II. The Mode of M2000 System Restore
All the content of incremental backup and full backup can be restored manually.
11.2.4 Name of Backup Files
After the execution of backup, the latest backup information will be recorded in "/export/home/backup/omc/backup.log". The information includes the generation date, path and name of the backup files. For example:
20040601042002 /export/home/backup/omc/all-20040601042002.tar.gz 0
20040602042001 /export/home/backup/omc/inc-20040602042001.tar.gz 1
20040603042002 /export/home/backup/omc/inc-20040603042002.tar.gz 1
In the above information, the first line indicates that the full backup file was generated on 2004-6-1 04:20:02. The second line means that the incremental backup file was generated on 2004-6-2 04:20:02. The third line indicates that the incremental backup file was generated on 2004-6-3 04:20:02.
The system sets the path and name of backup files automatically, and user can not set them manually.
11.2.5 Storage Media of Backup File
The backup files will be saved to disks or magnetic tapes or both according to the settings in the configuration file.
When the storage media is disk, system will save the backup files to "/export/home/backup/omc".
During the backup of the second week, the backup of the first week will be deleted automatically.
When the storage media is magnetic tape, system will wind the tape to the beginning, and then back up the files together with the path to the magnetic tape.
It is recommended to use a tape for each day. Prepare a tape before backup, and never replace the tape when the backup is underway.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-3
11.3 Function Setting
11.3.1 Introduction to Configuration File
Before backup or restoration, check whether the configuration related to backup or restoration in the configuration file "omcsvc.xml" meets the requirement. "omcsvc.xml" is in "/<M2000 installation directory>/opt/OMC/etc/conf/". It includes:
Tape drive path. Default: /dev/rmt/0 Storage media. Default: all (backup to both disk and tape).
1) If the above settings do not meet the requirement, refer to "11.3.2 Setting Tape Drive Path" and "11.3.2 6)Switch to root
bash-2.03$ su –root
2) Execute the following command to restart M2000 services:
# stop_svc
# start_svc
Setting Backup MediaSetting Backup Media " to modify the file "omcsvc.xml".
11.3.2 Setting Tape Drive Path
Perform the following operations to modify the path of tape drive:
1) Log in as omcuser. 2) Open the file "omcsvc.xml". 3) Find the following contents:
<path name="backuppath">
<param name="tapePath">/dev/rmt/0</param>
</path>
4) Replace "/dev/rmt/0" with the path of the tape drive. 5) Save the file and quit. 6) Switch to root
bash-2.03$ su –root
7) Execute the following command to restart M2000 services:
# stop_svc
# start_svc
11.3.3 Setting Backup Media
Perform the following operations to modify the path of tape drive:
1) Log in as omcuser. 2) Open the file "omcsvc.xml". 3) Find the following contents:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-4
<module name="all">
…..
<param name="backupMedia">all</param>
…....
</module>
…...
<module name="inc">
……
<param name="backupMedia">all</param>
……
</module>
Note:
"<module name="all">" and "<module name="inc">" respectively stands full backup and incremental backup. "<param name="backupMedia">all</param>" means that the backup is stored in both disk and magnetic tape. If the "all" in "<param name="backupMedia">all</param>" is "tape" or "disk", then it means that the backup will be saved in disk or tape only.
4) Change the "all" in "<param name="backupMedia">all</param>" to "tape" or "disk" according to the requirement.
5) Save the file and quit the edit status. 6) Switch to root
bash-2.03$ su –root
7) Execute the following command to restart M2000 services:
# stop_svc
# start_svc
11.4 Automatically Backing Up M2000 System
11.4.1 Introduction to Auto Backup
Auto backup, also called periodic backup, means that the system carries out backup at a fixed moment every day. In a week, the system carries out full backup on one day, and carries out incremental backup on other six days. The execution time and the full backup day can be set on M2000 Client.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-5
11.4.2 Setting Auto Backup Time
Perform the following operations on M2000 Client:
1) Log in to the Client. 2) In the main window, select the menu [Tools/System Backup/Periodic Backup]. 3) In the dialog box [Periodic Backup], select the tab "Server", and then select
"Enable Server Periodic Backup" and set the execution time and full backup day, as shown in Figure 11-1.
4) Click <OK> to save the settings. From then on, the system will carry out auto backup.
Figure 11-1 Periodic backup
11.5 Manually Backing Up M2000 System
11.5.1 Introduction to Manual Backup
Manual backup is carried in special or emergent circumstances, such as backup tape lost and system failure. The backup type can be full backup or incremental backup.
11.5.2 Carrying Out Manual Backup on Client
Perform the following operations on M2000 Client:
1) Log in to the Client. 2) In the main window, select the menu [Tools/System Backup/Manual Backup]. 3) In the dialog box [Manual Backup], select the tab "Server", and then select the
backup type, as shown in Figure 11-2.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-6
4) Click <Start> to start backing up M2000 system.
Figure 11-2 Manual backup
11.5.3 Carrying Out Manual Backup on Server
Perform the following operations on the M2000 Server:
1) Log in as root. 2) Execute the following command to carry out full backup:
# svc_backuprestore -cmd backup -m all -v
3) Or execute the following command to carry out incremental backup:
# svc_backuprestore -cmd backup -m inc -v
11.6 Restoring M2000 System
11.6.1 Function Introduction
Restore the M2000 system from the latest M2000 full backup and incremental backup file.
11.6.2 Operation Procedure
Perform the following operations on M2000 Server:
1) Log in as root. 2) If the M2000 services are running, execute the following command to stop the
M2000 services:
# stop_svc
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-7
3) Execute the following command to view the backup log "backup.log":
# cd /export/home/backup/omc
# more backup.log
20040601042002 /export/home/backup/omc/all-20040601042002.tar.gz 0
20040602042001 /export/home/backup/omc/inc-20040602042001.tar.gz 1
20040603042002 /export/home/backup/omc/inc-20040603042002.tar.gz 1
4) Make sure that the file recorded in backup.log is saved in the disk. If it is saved in the tape, it is necessary to copy the file from the tape to the disk in this way: Enter the root directory, insert the tapes from the first day to the last day one by one, and execute “tar” command to copy the file from the tape to the disk.
# cd /
# tar xf /dev/rmt/0
5) Execute the restoration command:
# svc_backuprestore -cmd restore
******************************************************
* Restore is a dangerous operation ! *
* If you have to do it, please stop system first ! *
******************************************************
Continue ?[n/y]
6) Press <Y> to start restoring M2000 system. 7) Execute the following command to start the M2000 services:
# start_svc
11.7 Backing Up Operating System
11.7.1 Function Introduction
Use the Solaris commands to back up the disk information (including Solaris, Sybase and M2000 software and parameters) to the tape.
11.7.2 Operation Procedure
The following description is based on Sun Fire V880. The operations on other server type are similar to this. The specific commands depend on the server type.
1) Log in as root. 2) Create a temporary directory:
# mkdir /data/backuprestore
# cd /data/backuprestore
3) Back up VTOC:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-8
# prtvtoc /dev/rdsk/c0t0d0s2 > ./c0t0d0.vtoc
# vxdisk list > vxdisk_list.out
# vxdg list
NAME STATE ID
rootdg enabled 1074053501.1025.f4800
m2000dg enabled 1074054023.1091.f4800
# vxprint -g rootdg -vpshm > rootdg.private
# vxprint -g m2000dg -vpshm > m2000dg.private
4) Back up vfstab:
# cp /etc/vfstab ./
5) Rewind the tape:
# mt rewind
6) Back up the partition information:
# cd /data
# ufsdump 0ucf /dev/rmt/0n backuprestore
7) Retrieve the partition information:
# df –k
Filesystem kbytes used avail capacity Mounted on
/dev/vx/dsk/rootvol 7059201 3887574 3101035 56% /
/proc 0 0 0 0% /proc
fd 0 0 0 0% /dev/fd
mnttab 0 0 0 0% /etc/mnttab
swap 7367984 16 7367968 1% /var/run
swap 7368296 328 7367968 1% /tmp
/dev/vx/dsk/m2000dg/data
24772232 19746352 4778158 81% /data
/dev/vx/dsk/opt 5646574 3041380 2548729 55% /opt
/dev/vx/dsk/m2000dg/exporthome
467699068 20191726 442830352 5% /export/home
8) Back up the partition data according to the above partition information ("/dev/vx/dsk/rootvol" and "/dev/vx/dsk/opt"):
# ufsdump 0ucf /dev/rmt/0n /dev/vx/rdsk/rootvol
# ufsdump 0ucf /dev/rmt/0n /dev/vx/rdsk/opt
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-9
11.8 Restoring Operating System
11.8.1 Function Introduction
Use the Solaris commands to restore the tape information (including Solaris, Sybase and M2000 software and parameters) to the disk so that the system can operate normally.
11.8.2 Operation Procedure
The following description is based on Sun Fire V880. The operations on other server type are similar to this. The specific commands depend on the server type.
1) Restore the tape information. 2) Set up equipment tree and boot block. 3) Modify the system file and file system information. 4) Restart the system. 5) Use Volume Manager to encapsulate the disk.
11.8.3 Restoring Tape Information
Perform the following operations to restore the information in the tape to the disk:
1) Start up the system using CD-ROM and enter the single user mode:
ok> boot cdrom –s
# TERM=vt100; export TERM
2) Rewind the tape:
# mt rewind
3) Restore the directory "backuprestore" in the tape to "/tmp/backuporestore".
# cd /tmp
# ufsrestore rf /dev/rmt/0n
4) Implement hard disk partition according to the hard disk vtoc backed up in the tape:
# fmthard –s /tmp/backuprestore/c0t0d0.vtoc /dev/rdsk/c0t0d0s2
5) Set up file system:
# newfs /dev/rdsk/c0t0d0s0
# newfs /dev/rdsk/c0t0d0s5
6) Restore the root partition:
# mkdir /tmp/root2
# mount /dev/dsk/c0t0d0s0 /tmp/root2
# cd /tmp/root2
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-10
# ufsrestore rf /dev/rmt/0n
Note:
Because the root partition is backed up first, it is restored first.
# rm restoresymtable
# cd /
# umount /tmp/root2
# fsck /dev/dsk/c0t0d0s0
7) Restore the partition "/opt":
# mkdir /tmp/root3
# ufsrestore rf /dev/rmt/0n
Note:
The restored one is the "/opt" backed up after the root partition.
# rm restoresymtable
# cd /
# umount /tmp/root3
# fsck /dev/dsk/c0t0d0s5
11.8.4 Setting Up Equipment Tree and Boot Block
Perform the following operations to set up equipment tree and boot block:
1) Delete the original equipment information:
# mount /dev/dsk/c0t0d0s0 /tmp/root2
# mv /tmp/root2/etc/path_to_inst /tmp/root2/etc/ORIGINAL_PATH_TO_INST
# rm /tmp/root2/dev/rdsk/c*
# rm /tmp/root2/dev/dsk/c* ; rm tmp/root2/dev/rmt/*
# cd /tmp/root2/devices ; rm -r *
2) Import the current equipment information:
# cd /devices; find . –print | cpio -pduVm /tmp/root2/devices
# cd /
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-11
# devfsadm -r /tmp/root2 -p /tmp/root2/etc/path_to_inst
# umount /tmp/root2
3) Set up the boot block:
# cd /usr/platform/sun4u/lib/fs/ufs; installboot ./bootblk /dev/rdsk/c0t0d0s0
# mount /dev/dsk/c0t0d0s0 /tmp/root2
# touch /tmp/root2/etc/vx/reconfig.d/state.d/install-db
11.8.5 Modifying System File and File System Information
Perform the following operations to modify the system file and file system information:
1) Set display output:
# TERM=vt100 ;export TERM
2) Open the file "system":
# vi /tmp/root2/etc/system
3) Disable the two lines in the file (add "#" before each line)
* rootdev:/pseudo/vxio@0:0
* set vxio:vol_rootdev_is_volume=1
4) Save the file "system" and quit. 5) Open the file "vfstab".
# vi /tmp/root/etc/vfstab
#device device mount FS fsck mount mount
# to mount to fsck point type pass at boot options
#
#/dev/dsk/c1d0s2 /dev/rdsk/c1d0s2 /usr ufs 1 yes -
fd - /dev/fd fd - no -
/proc - /proc proc - no -
/dev/vx/dsk/swapvol - - swap - no -
/dev/vx/dsk/rootvol /dev/vx/rdsk/rootvol / ufs 1 no -
/dev/vx/dsk/opt /dev/vx/rdsk/opt /opt ufs 2 yes -
swap - /tmp tmpfs - yes -
#NOTE: volume rootvol (/) encapsulated partition c0t0d0s0
#NOTE: volume swapvol (swap) encapsulated partition c0t0d0s1
#NOTE: volume opt (/opt) encapsulated partition c0t0d0s5
/dev/vx/dsk/m2000dg/data /dev/vx/rdsk/m2000dg/data /data ufs 2
yes logging
/dev/vx/dsk/m2000dg/exporthome /dev/vx/rdsk/m2000dg/exporthome
/export/home ufs 2
6) Delete the last two lines of in "vfstab":
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-12
/dev/vx/dsk/m2000dg/data /dev/vx/rdsk/m2000dg/data /data ufs 2
yes logging
/dev/vx/dsk/m2000dg/exporthome /dev/vx/rdsk/m2000dg/exporthome
/export/home ufs 2
7) Modify the following three lines in "vfstab": /dev/vx/dsk/swapvol - - swap - no -
/dev/vx/dsk/rootvol /dev/vx/rdsk/rootvol / ufs 1 no -
/dev/vx/dsk/opt /dev/vx/rdsk/opt /opt ufs 2 yes -
As:
/dev/dsk/c0t0d0s1 - - swap - no -
/dev/dsk/c0t0d0s0 /dev/rdsk/c0t0d0s0 / ufs 1 no -
/dev/dsk/c0t0d0s5 /dev/rdsk/c0t0d0s5 /opt ufs 2 yes –
Note:
The original "vfstab" is managed by "volume manager". The restored hard disk has no "volum manager", so the partitions managed by "volume manager" needs to be renamed using the standard partition name.
11.8.6 Restarting System
Execute the following command to restart the system:
# reboot
11.8.7 Encapsulating Disk Using Volume Manager
Execute the following commands to encapsulate the disk using Volume Manager:
1) Run Volume Manager
# vxinstall
According to the system prompts, enter the following information.
2) Some licenses are already installed. Do you wish to review them
[y,n,q,?] (default: y) y
3) Do you want to use enclosure based names for all disks ?
[y,n,q,?] (default: n) n
4) Volume Manager Installation Options
Menu: VolumeManager/Install
1 Quick Installation
2 Custom Installation
Administrator Guide iManager M2000 Mobile Element Management System Chapter 11 Backup and Restoration
11-13
3 Prevent multipathing/Suppress devices from VxVM's view
? Display help about menu
?? Display help about the menuing system
q Exit from menus
Select an operation to perform: 2
5) Encapsulate Boot Disk [y,n,q,?] (default: n) y
Enter disk name for [<name>,q,?] (default: rootdisk) rootdisk_1
Hit RETURN to continue.
6) Installation options for controller OTHER_DISKS
Menu: VolumeManager/Install/Custom/OTHER_DISKS
1 Install all disks as pre-existing disks. (encapsulate)
2 Install all disks as new disks. (discards data on disks!)
3 Install one disk at a time.
4 Leave these disks alone.
? Display help about menu
?? Display help about the menuing system
q Exit from menus
Select an operation to perform: 4
7) Is this correct [y,n,q,?] (default: y) y 8) Shutdown and reboot now [y,n,q,?] (default: n) n 9) Restart the system:
# reboot - - -x
Administrator Guide iManager M2000 Mobile Element Management System Chapter 12 Routine Maintenance
12-1
Chapter 12 Routine Maintenance
12.1 Overview of Routine Maintenance This chapter provides the maintenance items and operation guide for M2000, including:
Daily maintenance Weekly maintenance Monthly maintenance
These items are recommendation. You can customize them according to actual needs.
For operation and maintenance of NE, refer to iManager M2000 Mobile Element Management System Operation Manual.
12.2 Daily Maintenance
12.2.1 Daily Maintenance Item List
Table 12-1 lists the daily maintenance items. Refer to 12.2.2 “Checking Alarm Information” and the later section for operation guide of each maintenance item.
Table 12-1 Daily maintenance checklist
SN Item Reference
1 Check alarm information There is no alarm information.
2 Check log information There is no abnormal and malicious operations implemented.
3 Check Solaris error log There is no err message.
4 Check database status Database system operates normally, and the used space is lower than 80%.
5 Check hard disk space The used space of each partition is lower than 80%
6 Check CPU utilization CPU utilization is lower than 80%.
7 Check the number of processes The number of running processes is 18.
8 Check service status All the services are running normally.
12.2.2 Checking Alarm Information
Perform the following operations on M2000 Client:
1) Log in to the Client. 2) In the main window, select the menu [Tools/System Monitor/Monitor Browser].
Administrator Guide iManager M2000 Mobile Element Management System Chapter 12 Routine Maintenance
12-2
3) Select the tab "NE Monitor". 4) Check whether any alarm exists. 5) If any alarm exists, select the menu [Fault/Query/Current Alarm] to view its
detailed information.
12.2.3 Checking Log Information
Refer to "4.4 Browsing System Log" to check whether there is any system operation error.
Refer to "4.3 Browsing User Log" to check user operation log. If any abnormal or malicious operation is found, implement the corresponding handling. For example, if a user failed to log in to the Client for multiple times, check the validity of this user.
12.2.4 Checking Solaris Error Log
Refer to "4.5 Checking Solaris Error Log" to check whether the log contain any error information. If any error information is found, handle it according to Solaris system administrator manual.
12.2.5 Checking Database Status
Refer to "7.3 Querying Database Status" to check the database status and used space. If the free space of the database is insufficient, refer to 7.9 Clearing Database" to handle it.
12.2.6 Checking Hard Disk Space
Refer to "8.3 Query Disk Space" to check the space of the disk. If the free hard disk space is insufficient, refer to "8.4 Clearing Disk Space" to handle it.
12.2.7 Checking CPU Utilization
Refer to "5.4 Querying System Performance" to check the CPU utilization of the Server. If the CPU ululation is too high, refer to "5.5 Adjusting System Performance" to handle it.
12.2.8 Checking Number of Processes
Refer to "6.3 Querying Number of M2000 Processes" to check the number of processes. If the number is not enough, refer to "6.4 Querying Service Status" to check the processes which need to be started, and then refer to "6.5 Starting M2000 Services" to start them.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 12 Routine Maintenance
12-3
12.2.9 Checking Service Status
Refer to "6.4 Querying Service Status" to check the status of the services. If any one of them is abnormal, refer to "6.5 Starting M2000 Services" start the process or service to be started.
12.3 Weekly Maintenance
12.3.1 Weekly Maintenance Item List
Table 12-2 lists the weekly maintenance item of M2000 system. Refer to 12.3.2 “Backing Up M2000 System” and the later section for operation guide of each maintenance item.
Table 12-2 Weekly maintenance checklist
SN Item Reference
1 Backup M2000 system Open the [Periodic Backup] dialog box on M2000 Client, and select all the data to be backed up.
2 Check the M2000 Server time The time is right.
3 Find core files There are no core files on the Server.
4 Clear useless files Clear overdue log files, temporarily files and other useless files.
12.3.2 Backing Up M2000 System
1) Refer to "11.3.3 6)Switch to root
bash-2.03$ su –root
2) Execute the following command to restart M2000 services:
# stop_svc
# start_svc
Automatically Backing Up M2000" or "11.5 Manually Backing Up M2000 System" to back up M2000 system.
12.3.3 Checking M2000 Server Time
Perform the following operations on M2000 Server:
1) Log in as omcuser. 2) Execute the following command to view the current Server time:
bash-2.03$ date
3) To adjust time, refer to "2.2 Modifying Server Time".
Administrator Guide iManager M2000 Mobile Element Management System Chapter 12 Routine Maintenance
12-4
12.3.4 Finding core Files
Perform the following operations on M2000 Server:
1) Log in as omcuser. 2) Execute the following command to file the core files:
bash-2.03$ find / -name “core*” –ls
3) Read core files and delete the useless core files.
12.3.5 Clearing Useless Files
Refer to "8.4 Clearing Disk Space" to clear the useless files in the hard disk.
12.4 Monthly Maintenance
12.4.1 Monthly Maintenance Item List
Table 12-3 lists the monthly maintenance items of M2000 system. Refer to 12.4.2 “Checking Power Supply” and the later section for operation guide of each maintenance item.
Table 12-3 Monthly maintenance checklist
SN Item Reference
1 Check power supply The power supply of the Server is normal.
2 Check Server hardware The Server is not damaged physically.
3 Check the auxiliary devices of the Server
The devices such as the magnetic tape drive and CD-ROM drive are working normally.
12.4.2 Checking Power Supply
Check whether the power indicator of the Server indicates normal. Check whether the power supply of the Server is normal.
12.4.3 Checking Server Hardware
Check whether the hardware of the Server is damaged.
12.4.4 Checking Auxiliary Devices of Server
Check the following items for the auxiliary devices of the M2000 Server:
Check whether the CD-ROM can run normally. Check whether the tape drive can run normally.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 12 Routine Maintenance
12-5
For details of check CD-ROM and tape drive, refer to Solaris system administrator manual.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 13 Troubleshooting
13-1
Chapter 13 Troubleshooting
13.1 Overview of Troubleshooting This chapter introduces the following contents:
General troubleshooting procedure, including collection of fault information, fault location, range division and fault clearance.
Troubleshooting cases, detailing the analysis and handling of faults. Each section describes a fault.
For the maintenance and fault handling of Solaris, refer to Solaris system administrator manual.
For the maintenance and fault handling of Sybase database, refer to Sybase system administrator manual.
13.2 Troubleshooting Procedure
13.2.1 Overview of Troubleshooting Procedure
Generally, a troubleshooting procedure covers information collection, fault location and fault removal.
13.2.2 Information Collection
In case of a system fault, it is necessary to collect the following information:
Time and place of the fault occurrence Symptom Implemented measures and results after fault occurrence Version information IP information Alarm information Log information
The logs include user log, system log and trace log.
Internal problem location Information
Use the M2000 diagnostic tool to collect the internal problem location information. For details of the M2000 diagnostic tool, refer to "16.3 M2000 Diagnostic Tool".
13.2.3 Fault Location
Fault location refers to the processes of looking for the actual fault cause from many possible causes. Collection and analysis of fault information help locate the fault cause.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 13 Troubleshooting
13-2
M2000 system faults include hardware faults and software faults.
Hardware faults
The hardware faults include the ones occurring to M2000 Server, Client and networking equipment. The appearance and status indicators of hardware help locate hardware faults easily.
Software faults
The software faults include the ones occurring to M2000 system, the operating system and the database that M2000 is based on.
13.2.4 Fault Clearance
Clear the faults according to their causes:
Hardware faults
Refer to the manual delivered with device.
M2000 software faults
Refer to M2000 Client alarm online help to clear the faults.
For the clearance of faults related to software installation, refer to iManager M2000 Mobile Element Management System Installation Manual.
For the clearance of faults related to the Client, refer to iManager M2000 Mobile Element Management System Operation Manual.
For the clearance of faults related to the Server, refer to this chapter.
Solaris faults
Refer to Solaris system administrator manual.
Sybase database faults
Refer to Sybase system administrator manual.
Fault unable to clear
Collect all the information about an irremovable fault (refer to "13.2.2 Information Collection")and contact Huawei for handling immediately.
13.3 Auto Shutdown of Operating System
13.3.1 Symptom
When the serial port cable connecting the M2000 Server and terminal is removed, the operating system shuts down automatically.
13.3.2 Fault Analysis
Under the default settings of Solaris, when the Server is disconnected from the terminal, the system will be shut down automatically.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 13 Troubleshooting
13-3
13.3.3 Fault Clearance
Perform the following operations to clear the faults:
1) Reconnect the serial port cable between M2000 Server and the terminal. 2) Log in to the Server as root on the terminal. 3) Open the file "/etc/default/kbd". 4) Delete the "#" before "KEYBOARD_ABORT=alternate" in this file. 5) Save the change and quit. 6) Restart the system.
# /usr/sbin/shutdown –i6 –g0 –y
7) Remove the serial port cable between M2000 Server and the terminal, and the operating system will not shut down automatically.
13.4 Abnormal Service Restart
13.4.1 Symptom
Some services automatically restart abnormally.
13.4.2 Fault Analysis
The possible causes are:
Sybase is abnormal. The M2000 system is abnormal.
13.4.3 Fault Clearance
Perform the following operations to clear the fault:
1) Log in to the Server with the ID of "root". 2) Execute the following command to stop M2000 services:
# stop_svc
This command fails, execute the following command to stop the service:
# kill_svc
3) Execute the following command to stop Sybase:
# isql –SSYB –Usa –P<user sa password>
1> shutdown SYB_BACKUP
2> go
1> shutdown
2> go
4) Set Sybase operation parameter:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 13 Troubleshooting
13-4
Refer to iManager M2000 Mobile Element Management System Installation Manual to set Sybase operation parameters.
5) Execute the following command to restart Sybase:
# cd /opt/sybase/ASE-12_0/install
# ./startserver –f ./RUN_SYB
# ./startserver –f ./RUN_SYB_back
6) Execute the following command to start M2000 services:
# start_svc
7) View system log
View the system log file in "/export/home/omc/var/logs" to find the cause of abnormal service.
13.5 Abnormal Service Termination
13.5.1 Symptom
Execute the following command:
# svc_adm -cmd status
The output message contains "not running", meaning that this service is terminated abnormally.
13.5.2 Fault Analysis
The possible causes are:
Error occurs to program operation causing the abnormal termination of the service.
The startup procedure is manually terminated.
13.5.3 Fault Clearance
Perform the following operations to clear the fault:
1) Log in to the Server as root. 2) Execute the following command to start service:
# start_svc
Do not manually terminate the startup procedure.
3) If there is any service not started yet, contact Huawei for solution.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 13 Troubleshooting
13-5
13.6 M2000 Services Starting or Stopping Failure
13.6.1 Symptom
Executing one of the following commands fails:
start_svc stop_svc kill_svc
13.6.2 Fault Analysis
The possible causes are:
No execution runtime script is available before executing these commands. More that one user is executing the above commands at the same time.
13.6.3 Fault Clearance
Perform the following operations to clear the faults:
1) Log in to the Server as root.
Execute the runtime script. For the execution of runtime script, refer to "15.3 svc_profile.sh".
2) Make sure that only one user executes the above commands at the same time.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 14 Emergency Maintenance
14-1
Chapter 14 Emergency Maintenance
14.1 Overview of Emergency Maintenance This chapter provides the operation guide of emergency maintenance in the case of serious accident on M2000 Server or Client, including:
Emergency maintenance for M2000 Server Emergency maintenance for M2000 Client
14.2 Emergency Maintenance for M2000 Server
14.2.1 Function Introduction
If the problems of operating system abnormal, database abnormal or service failure occur to the Server, and cannot be cleared according to the methods introduced in "Chapter 13 Troubleshooting", you can recover the Server using the backup of the operating system and M2000 system.
14.2.2 Operation Procedure
Perform the following operations to recover the M2000 Server:
1) Recover the operating system If the operating system backup is available, refer to "11.8 Restoring Operating
System" to recover the operating system, database, M2000 software and parameter settings.
If the operating system backup is not available, refer to iManager M2000 Mobile Element Management System Installation Manual to reinstall the operating system.
2) Recover the M2000 system
Refer to "11.6 Restoring M2000" to recover the M2000 database data and M2000 system files.
14.3 Emergency Maintenance for M2000 Client
14.3.1 Function Introduction
If the problems of operating system abnormal or service failure occur to the Server, and cannot be cleared according to the methods introduced in "Chapter 13 Troubleshooting", you need to reinstall the Client.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 14 Emergency Maintenance
14-2
14.3.2 Operation Procedure
Perform the following operations to recover the M2000 Client:
1) Recover the operating system
Reinstall the operating system of the M2000 Client.
2) Recover the M2000 system
Refer to iManager M2000 Mobile Element Management System Installation Manual to reinstall the M2000 Client software.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 15 Command Guide
15-1
Chapter 15 Command Guide
15.1 Overview of Command Guide This chapter consists of the following contents:
Introduction to commands: introduces the path of the commands and prerequisites of using them.
svc_profile.sh: introduces the functions and running of the environment script. Functions of some important commands and the corresponding examples.
15.2 Introduction to Commands
15.2.1 Path of Commands
The M2000 system maintenance commands are stored in "/<M2000 installation directory>/bin".
15.2.2 Prerequisites of Using Commands
The prerequisites of using M2000 commands are:
Sybase is running normally. The M2000 environment setting script svc_profile.sh has been executed.
15.3 svc_profile.sh
15.3.1 Function of svc_profile.sh
It is necessary to execute the script, svc_profile.sh, before using the M2000 commands. This script is used to set the user’s working environment, such as command search path and dynamic library search path.
15.3.2 Path of svc_profile.sh
The script, svc_profile.sh, is in "/<M2000 installation directory>".
15.3.3 Running svc_profile.sh
The script, svc_profile.sh, can be manual running and auto running.
Manual running
The method of manually running this script is:
bash-2.03$ . /<M2000 installation directory>/svc_profile.sh
Administrator Guide iManager M2000 Mobile Element Management System Chapter 15 Command Guide
15-2
Caution:
There must be a “.” at the beginning of a command, and a space between “.” and “/”.
Auto running
After the installation of the system according to iManager M2000 Mobile Element Management System Installation Manual, the script is added to the file ".profile" of "omcuser" and "root". If you log in as omcuser or root, the system will automatically run this script.
Note:
iManager M2000 Mobile Element Management System Installation manual introduces the settings of the file ".profile" of "omcuser" and "root".
15.4 start_svc
15.4.1 Command Function
This command is used to start all the M2000 services. If the services have been already started, this command will try to start each service, and prompts that each service is already running.
15.4.2 Example
# start_svc
============================ Starting Services ...
TAO Naming Service is running
TAO Notification Service is running
Monitor_Service already running.
imapsysd already running.
LogServer [starting... ]
svc_adm:info:service with this name is already running
…...
============================ Finished Starting Services.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 15 Command Guide
15-3
15.5 stop_svc
15.5.1 Command Function
This command is used to stop all the M2000 services If the services are not started yet, this command will try to stop each service and prompts error.
15.5.2 Example
# stop_svc
============================ Stopping System ...
SystemMonitor [stopped ]
EventManager [stopped ]
LogServer [stopped ]
…...
============================ Finished Stopping System.
15.6 kill_svc
15.6.1 Command Function
This command stops all the M2000 processes and services using the kill process mechanism of the operating system. It is an extreme measure to use this command. It may cause data loss and service abnormal.
In normal cases, use stop_svc to stop all the M2000 services. Do not use kill_svc to kill the processes unless in special cases such as when the process is abnormal.
15.6.2 Example
# kill_svc
15.7 svc_adm –cmd status
15.7.1 Command Function
This command is used to view the current running status of all M2000 services.
15.7.2 Example
bash-2.03$ svc_adm –cmd status
The current status ("running" or "not running") of all services will be displayed.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 15 Command Guide
15-4
15.8 svc_ps
15.8.1 Command Function
This command is used to query the running status of all M2000 processes.
15.8.2 Example
bash-2.03$ svc_ps
This command returns the running M2000 processes in the system.
15.9 top
15.9.1 Command Function
This command is used to display the total CPU and memory utilization in the system and the CPU and memory utilization of each process.
15.9.2 Example
bash-2.03$ top
load averages: 0.03, 0.11, 0.30 10:37:25
107 processes: 106 sleeping, 1 on cpu
CPU states: 99.4% idle, 0.0% user, 0.6% kernel, 0.0% iowait, 0.0% swap
Memory: 4096M real, 2655M free, 8099M swap free
PID USERNAME THR PRI NICE SIZE RES STATE TIME CPU COMMAND
346 root 52 59 0 109M 101M sleep 632:43 0.32% dataserver
5378 root 22 58 0 95M 67M sleep 0:08 0.09% imapsvcd
5371 root 21 58 0 61M 30M sleep 0:07 0.07% imapsysd
6726 root 1 58 0 2160K 1664K cpu0 0:00 0.07% top
…...
Table 15-1 lists the meanings of the columns in the returned message of the command "top".
Table 15-1 Meanings of columns in returned message of command "top"
Column Meaning
PID Process number
USERNAME Name of the user running this process
THR Thread number
PRI Priority
NICE Indicates whether this process is normal
Administrator Guide iManager M2000 Mobile Element Management System Chapter 15 Command Guide
15-5
Column Meaning
SIZE Size of buffer and memory occupied by this process (unit: megabyte)
RES Size of memory occupied by this process (unit: megabyte)
STATE Current status of this process. If the process is running, then the CPU it uses is displayed.
TIME The time this process has been running by far
CPU CPU utilization of this process
COMMAND Command that starts this process
15.10 svc_adm –cmd reload
15.10.1 Command Function
This command is used to load the configuration data from the configuration file imap.xml to the system configuration module. This command realizes the real time update of configuration information during M2000 service running.
15.10.2 Example
bash-2.03$ svc_adm –cmd reload
After executing this command, the configuration data in the configuration module is the same as the data in the file imap.xml.
15.11 svc_stacks
15.11.1 Command Function
This command is used to collect the stack information of the M2000 services. It is used in internal problem location and commissioning.
15.11.2 Example
bash-2.03$ svc_stacks
After executing this command, the query results will be saved in "/<M2000 installation directory>/var/logs/imap_stacks.YY_MM_DD__HH:MM:SS".
In the above description, "YY" is the last two digits of the year, "MM" is the month, "DD" is the date, "HH" is the hour, "MM" is the minute and "SS" is the second.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 15 Command Guide
15-6
15.12 svc_lockdump
15.12.1 Command Function
This command is used to collect the lock status of the current management objects. It is used in internal problem location and commissioning.
15.12.2 Example
bash-2.03$ svc_lockdump
Dump MO Locks information successfully.
After executing this command, the query results will be saved in "/<M2000 installation directory>/var/logs/iMAP.lock.dump".
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-1
Chapter 16 Tool Guide
16.1 Overview of Tool Guide This chapter introduces the functions and usages of M2000 tools.
16.2 Tape Drive Management Tool
16.2.1 Function
The tape drive management tool provides GUI for the user to manage various types of type drive, including the produces of Sony, HP and Sun.
16.2.2 Starting method
Perform the following operations on M2000 Server:
1) Log in as omcuser. 2) Execute the following command to check whether the status of the tape drive is
normal:
bash-2.03$ mt -f /dev/rmt/0 status
HP DDS3 4mm DAT tape drive:
sense key(0x6)= Unit Attention residual= 0 retries= 0
file no= 0 block no= 0
If the status information of the tape drive can be displayed, it means that the tape drive is running normally.
3) Execute the following command to start the tape management tool:
bash-2.03$ . /<M2000 installation directory>/tapemanager/tapemanager.sh
Figure 16-1 illustrates the main interface of the tape drive management tool.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-2
Local diskdirectory tree
Disk fileinformationoutput area
Tape drivedirectory tree
Tape drive fileinformationoutput area
Figure 16-1 Tape drive management tool
16.2.3 Operation Guide
The tape drive management tool provides the following operations:
Caution:
It is necessary to load the tape before any operation. The possible causes of tape loading failure are tape drive not connected correctly, tape damaged, no tape in the tape drive and tape drive busy.
Load and eject: Load the tape into the tape drive, eject the tape from the tape drive Format tape: Format the tape to the specified format Backup and restoration files: back up the files in the disk to the tape drive, restore
the files in the disk Search files: search for a file in the tape drive or disk Query tape drive status Refresh Delete
16.3 M2000 Diagnostic Tooling
16.3.1 Function
This tool can be used to collect and save the problem locating information of the Server and Client to the specified directory in the Server or Client. The information includes:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-3
Client trace log Client JAVA virtual machine thread stacks and lock status Server trace log Server core files Queue synchronization pointer of software management Number and status of background threads, that is, the result of pstack Lock status of MO Alarm synchronization numbers of the NEs Alarm diagnostic data.
16.3.2 Running Diagnostic Tool
Perform the following operations to run the diagnostic tool:
1) Log in to the Client. 2) Select the menu [Start/iManager M2000 Client/M2000 Diagnosis] to run the
diagnostic tool. The window [M2000 Diagnostic Tool] is displayed, as shown in Figure 16-2.
Figure 16-2 M2000 diagnostic tool
3) In the window [M2000 Diagnostic Tool], click <Setting> to open the window [FTP Server Setting], as shown in Figure 16-3.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-4
Note:
If the tool parameters have been set, step 2) and 3) can be skipped.
Figure 16-3 FTP service setting
4) In the dialog box [FTP Server Setting], enter the parameter information, and then click <OK>.
IP Address: Server IP Port: FTP service port number. Normally the default value 10119 is adopted. If it
needs to be modified, then the setting on the Server also needs to be modified. To modify the service parameter setting, log in to the Server as ftpuser and execute the command "start_collector –port <port number>".
FTP User Name: ftpuser Password: password of Solaris user "ftpuser" Delete the collected files in Server after collecting: if select it, the collected
information will be deleted from the Server, and only stored in the Client; if do not select it, the collected information will be saved to both the Client and "/export/home/omc/var/DebugInfo" in the Server.
5) In the window [M2000 Diagnostic Tool], enter the time and file path. If you want to collect some NE’s alarm diagnostic data, select “Collect Alarm Diagnostic Data”, and input the NE name. Then click <Collect> to start collecting Diagnostic information.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-5
16.3.3 Abnormal Handling
If you fail to run the diagnostic tool, perform the following operations:
1) Log in to the Server as root. 2) Check whether the diagnostic service is running:
# ps -ef | grep start_collector | grep -v grep
If there is any message returned, it means that the service is running. Otherwise, the service is not running.
Note:
Normally, the diagnostic service start to run automatically after M2000 Server application software is installed successfully.
3) Start the diagnostic service if it is not running yet.
# start_collector
4) Restart diagnostic tool on the Client. Refer to 16.3.2 “Running Diagnostic Tool”.
16.3.4 Forbidding Using Diagnostic Tool
To forbid using diagnostic tool, perform the following operations on the Server to stop diagnostic service:
1) Log in to the Server as root. 2) Stop diagnostic service:
# stop_collector
16.4 Performance Job Result Auto Export Tool
16.4.1 Function
The performance job result auto export tool is used to automatically export the performance job results. After running this tool, the system periodically exports the specified job results to a file.
The exported job results will not be deleted from the performance database. They will be deleted after they have been stored for a period of time (defined when the task is created).
16.4.2 Function Settings
You can configure the export function by modifying the configuration file "/<M2000 installation directory>/bin/PMExporst.cfg".
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-6
This file consists of the following four parts:
PATH=/export/home/omc/var/backup/pm/
The storage directory of the exported file. In this example, the directory is /export/home/omc/var/backup/pm/. When this tool is running, it creates a sub-directory under this directory every day. The name of a sub-directory is "PMExporst_<the current date>". All files generated that day are saved in this sub-directory. The name of an exported file is "PMResult_<task number>_<start time>_<end time>.csv".
SAVEDAYS=3
The storage days of the exported file. In this example, the file will be kept for three days. After the storage days, it will be deleted from the disk.
DELAY=30
Because some NEs may report performance job results with delay, M2000 can export the results of the previous measurement period only after a delay of several minutes. The setting here indicates that the delay is set to 30 minutes. The delay ranges from 30 to the integer multiple of 30.
101:30
The job number and the job’s export period. The export period (unit: minute) can be set as 30, 60 or 1440. In this example, 101 is the task number, and the export period is 30 minutes.
To export multiple jobs’ result, it is necessary to add multiple entries of such information to the configuration file. For example:
102:60
103:1440
The parameter PATH, SAVEDAYS and DELAY is the same for each task, and only the export period is different for each task.
Because the processing of performance task results takes some time, the task of a period is exported 30 minutes later. For example, if the export period is 60 minutes, then the data within 1:00–2:00 will be exported at 2:30, and the data within 2:00–3:00 will be exported at 3:30.
16.4.3 Running Auto Export Tool
Caution:
When this tool is running, you cannot start this tool again.
Perform the following operations on the Server to run the auto export tool:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-7
1) Log in as omcuser. 2) Run the auto export tool PMExporst.
bash-2.03$ nohup PMExporst SYB sa <sa user password> &
After that, job results of each time segment is exported to files after a delay automatically. The time segment is divided according to export period, see Table 16-1.
Table 16-1 Export period and time segment
Export period ( minute) Time segment
30 Every 30 minutes starting from 0:00. For example, 0:00-0:30, 0:30-1:00, 1:00-1:30, 1:30-2:00......
60 Every hour starting from 0:00. For example, 0:00-1:00, 1:00-2:00, 2:00-3:00, 3:00-4:00......
1440 Every day. For example, 0:00-24:00
For example, to export the results with the export period of 60 minutes and the delay of 30 minutes, the result of 0:00–1:00 will be exported at 1:30, and the result of 1:00–2:00 will be exported at 2:30.
16.4.4 Stopping Auto Export Tool
Perform the following operations on the Server to stop the service:
1) Log in as omcuser. 2) Stop the auto export tool:
bash-2.03$ ps -ef | grep PMExporst | grep -v grep
3) Query the process ID (pid) of PMExporst, and stop this process:
bash-2.03$ kill -9 <pid>
16.4.5 Abnormal Handling
If the result files cannot be generated as expected, perform the following operations:
1) Execute the following command to check whether the service is running:
bash-2.03$ ps -ef | grep PMExporst | grep -v grep
2) If the service is not running, check whether any error prompt exists in the file "/opt/OMC/bin/nohup.out". The possible cause is that wrong parameter was entered when starting the tool.
3) Check whether any error information exists in the log file " /opt/OMC/bin/PMExporest.log".
4) If the service is running, the possible cause is that the task does not exist or it has not report result yet. The related information can be viewed in the log file
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-8
"/opt/OMC//var/logs/PMExporest.log". If a task does not exist, it will not affect the export of other task results.
16.5 IP Modification Tool
16.5.1 Function
M2000 provides the IP modification tool based on command line mode for the system administrator to implement IP setting and query of Solaris and Sybase data base.
The path of the IP modification tool is "/<M2000 installation directory>/bin".
16.5.2 Prerequisites
The prerequisites of running the IP modification tool are as follows:
The M2000 system has been installed successfully. The environment setting script is running (refer to "15.3 svc_profile.sh"). Log in as root.
16.5.3 Querying IP Settings
I. Command format
# iptools –l
II. Example
# iptools –l
InterfaceName IPAddress MACAddress
------------------------------------------------------------
eri0 Titan 00:03:ba:12:f9:12
------------------------------------------------
Sybase Listener IP Address Port
------------------------------------------------
10.161.45.241 4100
The output message displays the current system IP settings:
Interface name: eri0 IP address: Titan. "Titan" is the host name. Its corresponding IP address can be
queried in the file "\etc\hosts". Mac address: 00:03:ba:12:f9:12 Sybase listen address: 10.161.45.241 Port number: 4100
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-9
16.5.4 Modifying Solaris IP Address, Host name, Default Gateway and Subnet Mask
I. Command format
# iptools {-n interface-name -i ip-address -m subnet-mask -G default -gateway -H host-name -d }
Parameter description:
-n: Ethernet adapter interface name -i: IP of the Ethernet adapter (decimal IP address) -G: Default gateway of Solaris -H: Host name of Solaris -d: Switch, which means that the IPs of all database services of Sybase are set as
the new IPs
II. Example
Set all interfaces. The Solaris IP is 10.70.141.54, host name is "host", default gateway is 10.70.141.1, and the IPs of all servers of Sybase are 10.70.141.54.
# iptools –n hme0 –i 10.70.141.54 –m 255.255.255.0 –G 10.70.141.1 –H host –d
change net default: gateway 10.70.141.1
set new ip : 10.70.141.54 succeed !
set all services of sybase ip 10.70.141.54 succeed !
set old hostname : UFO ---> new hostname : host succeed !
Set the Ethernet adapter interface. The interface name is "hme0", the IP is 10.70.141.54, and the subnet mask is 255.255.255.0.
# iptools –n hme0 –i 10.70.141.54 –m 255.255.255.0
set new ip : 10.70.141.54 succeed !
16.5.5 Modifying Sybase IP
I. Command format
# iptools -D ip-address
II. Example
Set IP interface descriptions of all Sybase database services.
# iptools –D 10.70.141.54
set all services of sybase ip 10.70.141.54 succeed !
Administrator Guide iManager M2000 Mobile Element Management System Chapter 16 Tool Guide
16-10
16.5.6 Modifying Sybase Service IP and Port Number
I. Command format
# iptools {-S service-name -D ip-address -P port }
II. Example
Set the IP of the SYB service of Sybase database as 10.70.141.54 and the port number as 4000.
# iptools –S SYB –D 10.70.141.54 –P 4000
set service SYB with ip 10.70.141.54 succeed !
16.5.7 Modifying Host Name
I. Command format
# iptools -H host-name
II. Example
Modify the Solaris host name as "omc".
# iptools –H omc
set old hostname : host ---> new hostname : omc succeed !
If the new name is the same as the original name, the system will prompt:
omc is same with the current host name !
16.5.8 Modifying Gateway
I. Command format
# iptools -G gateway
II. Example
Set the Solaris gateway as 10.70.141.1.
# iptools –G 10.70.141.1
change net default: gateway 10.70.141.1
If the modification of gateway fails, the system prompts:
change default gate failed!!
Administrator Guide iManager M2000 Mobile Element Management System Chapter 17 FAQ
17-1
Chapter 17 FAQ
17.1 Overview of FAQ This chapter introduces the frequently asked questions and the solutions concerning Solaris operating system and Sybase database.
17.2 Logging in as root though Telnet
17.2.1 Question
Why can't I log in as root through Telnet?
17.2.2 Answer
For the sake of security, the user root can log in to the system only through the console after Solaris8 is installed. If it is necessary to log in to the system through telnet as root, follow the procedure below. It is recommended restoring the original setting after that.
1) Log in as root. 2) Open the file "/etc/default/login". 3) Find the line of CONSOLE=/dev/console. Add "#" in the front of the line to turn it to
a comment line. 4) Save the settings and exit.
17.3 Logging in as root though FTP
17.3.1 Question
Why can't I log in as root through FTP?
17.3.2 Answer
For the sake of security, the user root does not have the authority to use FTP by default. If it is necessary to log in to the system as root through ftp, follow the procedure below. It is recommended restoring the original setting after that.
1) Log in as root. 2) Open the file “/etc/ftpusers” 3) Find the line of root user, and delete the line. 4) Save the settings and exit.
Administrator Guide iManager M2000 Mobile Element Management System Chapter 17 FAQ
17-2
17.4 Installing Tape Drive
17.4.1 Question
How to install tape drive for the Server?
17.4.2 Answer
The built-in tape drive does not require the installation of driver. When the Server is started up, it will be identified automatically. The external tape drive requires the installation of driver. In the case of Sun Ultra 60, the installation is as follows:
1) Power off all peripherals; 2) Set the ID switch of the tape drive to 4 or 5; 3) To use the SCSI interface, connect the SCSI cable to the IN interface of the tape
drive. 4) Power on all peripherals and the host, and boot the system. 5) Log in as root. 6) Execute the following command to view the tape drive status:
# mt –f /dev/rmt/0mn status
The above command can be abbreviated as “mt status”.
The following prompts may appear:
HP DDS-3 4MM DAT tape drive:
sense key(0x6)= Unit Attention residual= 0 retries= 0
file no= 0 block no= 0
This means that the tape drive is normal. There is a tape in the tape drive, and the tape has been rewound to the beginning.
No such device or address
This means that the tape drive is not connected with the work station or the connection is incorrect.
/dev/rmt/0n: no tape loaded or drive offline
This means that the tape or tape drive is in offline state.
/dev/rmt/0n: No such file or directory
This means that the tape drive is not attached.
7) If the tape drive is not attached, execute the following command to attach the tape drive:
# drvconfig
# tapes
8) When the tape drive is attached, insert a tape, and then execute the following command to view the tape drive status:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 17 FAQ
17-3
# mt status
17.5 Setting Default Route
17.5.1 Question
How to set the default route in Solaris system? For example, there multiple NodeBs are controlled by one RNC. How to set the RNC IP as the default route IP, so as to establish a maintenance channel from M2000 to NodeBs?
17.5.2 Answer
Perform the following operations on the Server:
1) Log in as root. 2) Execute the following command:
# vi /etc/defaultrouter
3) Enter the default route IP in the file, for example:
10.161.44.1
4) Save the change and quit vi. 5) Execute the following command to restart the Server:
# init 6
17.6 Adding and Deleting Routes
17.6.1 Question
How to add and delete routes in Solaris system? For example, how to establish the maintenance channels to NodeBs controlled by multiple RNCs?
17.6.2 Answer
Perform the following operations on the Server:
1) Log in as root. 2) Perform the following operations according to the actual needs:
Too add a route, execute the following command:
# route add <destination address>/<subnet mask> <gateway>
Destination address: can be either a network address or a host address.
Subnet mask: Must be a number, that is, the total number of "1" in the binary subnet mask.
For example, "32" means "255.255.255.0".
For example, route add 129.8.0.0/32 10.12.8.1
Administrator Guide iManager M2000 Mobile Element Management System Chapter 17 FAQ
17-4
To delete a route, execute the following command:
# route delete <destination address>/<subnet mask> <gateway>
For example, route delete 129.8.0.0/32 10.12.8.1
To view the route information, execute the following command:
# netstat –rv
To enable the system to automatically execute the route adding command on system startup, create the file "/etc/rc2.d/S97route":
# vi /etc/rc2.d/S97route
Write one or more entries of router add <destination address>/<subnet mask> <gateway> commands in this file. For example:
route add 129.9.0.1/32 10.12.8.1
route add 129.8.0.0/16 10.12.8.1
17.7 "/etc/rc2.d" in Solaris
17.7.1 Question
What are the meanings of the files in the directory "/etc/rc2.d" in Solaris?
17.7.2 Answer
There are two types of files in "/etc/rc2.d": those with the initial letter of capitalized "S" and those with the initial letter of capitalized "K".
During the startup of Solaris, the system executes all script files with the initial letter of "S" in "/etc/rc2.d" in alphabetical order.
During the shutdown of Solaris, the system executes all script files with the initial letter of "K" in "/etc/rc2.d" in alphabetical order.
The installation software of M2000 Server will generate three startup files in "/etc/rc2.d/": S98sybase (for starting Sybase), S98TAO (for starting TAO service) and S99IMAP (for starting M2000 services).
17.8 Querying Hardware Configuration of Server
17.8.1 Question
How to query the hardware configuration of the Sun server? How to check the size of memory?
17.8.2 Answer
Perform the following configurations on the Server:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 17 FAQ
17-5
1) Log in as root. 2) Execute the following command:
# prtconf
System Configuration: Sun Microsystems sun4u
Memory size: 512 Megabytes
System Peripherals (Software Nodes):
SUNW,Ultra-60
packages (driver not attached)
terminal-emulator (driver not attached)
In the message above, "Memory size: 512 Megabytes" indicates the size of memory, and "SUNW, Ultra-60" is the type of the Server.
17.9 Confirming Startup of Sybase
17.9.1 Question
How to check the startup status of Sybase?
17.9.2 Answer
Perform the following operations on the Server to check the status of Sybase:
1) Log in as dbuser. 2) Execute the following command:
bash-2.03$ cd /opt/sybase/ASE-12_0/install
bash-2.03$ ./showserver
root 21684 21683 0 October 29 ? 0:00 /opt/sybase/ASE-12_0/bin/backupserver
-SSYB_back -e/opt/sybase/ASE-12_0/install
root 23718 23716 7 November 01 ? 678:28 /opt/sybase/ASE-12_0/bin/dataserver
-sSYB -d/data/master_dev.dat -e/opt/sybase/
If the returned message contains "dataserver" and "backupserver", it means that the active and standby databases are both started.
17.10 Starting Sybase
17.10.1 Question
How to start Sybase service?
17.10.2 Answer
Perform the following operations on the Server to start Sybase service:
Administrator Guide iManager M2000 Mobile Element Management System Chapter 17 FAQ
17-6
1) Log in as dbuser. 2) Execute the following command:
bash-2.03$ cd /opt/sybase/ASE-12_0/install/
bash-2.03$ ./startserver -f ./RUN_SYB
bash-2.03$ ./startserver -f ./RUN_SYB_back
17.11 Stopping Sybase
17.11.1 Question
How to stop Sybase service?
17.11.2 Answer
Perform the following operations on the Server to stop Sybase service:
1) Log in as dbuser. 2) Execute the following command:
bash-2.03$ isql -SSYB -Usa -P<password of user sa>
1> shutdown SYB_BACKUP
2> go
1> shutdown
2> go
Note:
If the M2000 Server software has been installed, Sybase will be started automatically after the startup of the operating system.
Administrator Guide iManager M2000 Mobile Element Management System Appendix Acronyms and Abbreviations
1
Appendix Acronyms and Abbreviations
C
CORBA Common Object Request Broker Architecture
CPU Central Processing Unit
E
EMS Element Management System
F
FAQ Frequent Ask Question
FTP File Transfer Protocol
I
ID Identity
IDL Interface Description Language
IP Internet Protocol
L
LMT Local Maintenance Terminal
M
MB Mega Byte
N
NMS Network Management System
NTP Network Time Protocol
O
OMC Operation & Maintenance Center
P
PID Process Identification
R
RNC Radio Network Controller
S
SCSI Small Computer Systems Interface
SQL Structured Query Language
T
Administrator Guide iManager M2000 Mobile Element Management System Appendix Acronyms and Abbreviations
2
TCP Transfer Control Protocol
Administrator Guide iManager M2000 Mobile Element Management System Index
i-1
Index
A adding
M2000 user, 3-6
M2000 user group, 3-6
operating system user, 3-3
route, 17-3
adjusting
system performance, 5-3
alarm data
displacing automatically, 7-6
displacing manually, 7-5
B backing up
M2000 system, 11-4, 11-5
operating system, 11-7
backup and restoration
database, 11-1
introduction, 11-1
setting, 11-3
browsing
system log, 4-3
user log, 4-3
C checking
NTP service, 10-3
solaris error log, 4-3
Sybase, 17-5
clearing
database, 7-8
disk space, 8-3
pmdb, 7-7
client
emergency maintenance, 14-1
file system, 8-2
collecting
fault information, 16-2
command
kill_svc, 15-3
start_svc, 15-2
stop_svc, 15-3
svc_adm –cmd reload, 15-5
svc_adm –cmd status, 15-3
svc_lockdump, 15-6
svc_profile.sh, 15-1
svc_ps, 15-4
svc_stacks, 15-5
top, 15-4
creating
M2000 user, 3-6
M2000 user group, 3-6
operating system user, 3-3
D daily maintenance
item list, 12-1
operation guide, 12-1
database
clearing, 7-8
fmdb, 7-2
introduction, 7-1
modifying user password, 3-5
omcdb, 7-1
pmdb, 7-2
querying, 7-4
sysmdb, 7-3
user account, 3-3
dbuser
introduction, 3-2
modifying password, 3-4
default route
setting, 17-3
deleting
route, 17-3
Administrator Guide iManager M2000 Mobile Element Management System Index
i-2
diagnosis
tool, 16-2
disk space
clearing, 8-3
querying, 8-2
displacing
alarm data, 7-5, 7-6
user log, 7-5, 7-7
dual-plane
automatically setting, 9-3
configuration procedure, 9-2
introduction, 9-1
manually setting, 9-2
verifying, 9-4
dumping. see displacing
E emergency maintenance
client, 14-1
server, 14-1
exporting
performance result, 16-5
F file system
client, 8-2
introduction, 8-1
server, 8-1
fmdb
backup and restoration, 11-1
displacing automatically, 7-6
displacing manually, 7-5
introduction, 7-2
FTP
logging, 17-1
ftpuser
introduction, 3-2
ftpusr
modifying password, 3-4
G gateway
modifying, 16-8
H host name
modifying, 2-2, 16-8
I inrpt
introduction, 3-2
installing
tape drive, 17-2
introduction
backup and restoration, 11-1
command, 15-1
database, 7-1
dual-plane, 9-1
file system, 8-1
fmdb, 7-2
log, 4-1
NE log, 4-1
NTP, 10-1
omcdb, 7-1
pmdb, 7-2
process, 6-1
service, 6-1
sysmdb, 7-3
system log, 4-2
trace log, 4-2
user account, 3-1
user log, 4-1
IP
modifying, 2-3, 16-8
querying, 16-8
L log
introduction, 4-1
NE log, 4-1
system log, 4-2
trace log, 4-2
type, 4-1
user log, 4-1
Administrator Guide iManager M2000 Mobile Element Management System Index
i-3
logging
through FTP, 17-1
through Telnet, 17-1
M M2000
auto startup, 17-4
backing up automatically, 11-4
backing up manually, 11-5
creating user, 3-6
creating user group, 3-6
monitoring user, 3-6
restoring, 11-6
user account, 3-3
modifying
gateway, 16-8
host name, 2-2, 16-8
IP, 2-3, 16-8
time, 2-1
user password of database, 3-5
user password of operating system, 3-4
monitoring
M2000 user, 3-6
server status, 5-1
monthly maintenance
item list, 12-4
operation guide, 12-4
multiple IPs
setting, 2-4
N NE log
introduction, 4-1
NTP
checking, 10-3
introduction, 10-1
setting middle NTP server, 10-2
setting NTP client, 10-2
setting top NTP server, 10-2
starting, 10-2
stopping, 10-3
O omcdb
backup and restoration, 11-1
displacing automatically, 7-7
displacing manually, 7-5
introduction, 7-1
omcuser
introduction, 3-2
modifying password, 3-4
operating system
backing up, 11-7
creating user, 3-3
modifying user password, 3-4
restoring, 11-9
user account, 3-1
P pmdb
backup and restoration, 11-1
clearing, 7-7
exporting job result, 16-5
introduction, 7-2
procedure
configuring dual-plane, 9-2
emergency maintenance, 14-1
troubleshooting, 13-1
process
introduction, 6-1
querying number, 6-6
Q querying
database, 7-4
disk space, 8-2
hardware configuration, 17-4
IP, 16-8
process number, 6-6
server status, 5-1
service status, 6-6
system performance, 5-2
Administrator Guide iManager M2000 Mobile Element Management System Index
i-4
R removing. see deleting
restoring
M2000 system, 11-6
operating system, 11-9
root
introduction, 3-1
modifying password, 3-4
route
adding, 17-3
deleting, 17-3
setting, 17-3
routine maintenance
daily maintenance, 12-1
monthly maintenance, 12-4
weekly maintenance, 12-3
S sa
introduction, 3-3
modifying password, 3-5
server
auto startup, 17-4
emergency maintenance, 14-1
file system, 8-1
querying hardware configuration, 17-4
querying status, 5-1
setting status alarm threshold, 5-2
service
introduction, 6-1
querying status, 6-6
starting, 6-8
stopping, 6-9
setting
backup and restoration, 11-3
default route, 17-3
gateway, 16-8
host name, 2-2, 16-8
IP, 2-3, 16-8
middle NTP server, 10-2
multiple IPs, 2-4
NTP client, 10-2
threshold server status alarm, 5-2
top NTP server, 10-2
solaris error log
checking, 4-3
starting
M2000 service, 6-8
NTP service, 10-2
Sybase, 17-5
startup file
for M2000, 17-4
for Sybase, 17-4
stopping
M2000 service, 6-9
NTP service, 10-3
Sybase, 17-6
stting
time, 2-1
Sybase
auto startup, 17-4
checking, 17-5
starting, 17-5
stopping, 17-6
sysmdb
backup and restoration, 11-1
introduction, 7-3
system log
browsing, 4-3
introduction, 4-2
system performance
adjusting, 5-3
querying, 5-2
T tape drive
installing, 17-2
management, 16-1
Telnet
logging, 17-1
time
modifying, 2-1
trace log
introduction, 4-2
Administrator Guide iManager M2000 Mobile Element Management System Index
i-5
troubleshooting
case, 13-2
fault clearance, 13-2
fault location, 13-1
information collection, 13-1
procedure, 13-1
tool, 16-2
U user account
database, 3-3
dbuser, 3-2
ftpuser, 3-2
inrpt, 3-2
introduction, 3-1
M2000, 3-3
omcuser, 3-2
operating system, 3-1
root, 3-1
type, 3-1
user authority
database, 3-3
M2000, 3-3
operating system, 3-1
user log
browsing, 4-3
displacing automatically, 7-7
displacing manually, 7-5
introduction, 4-1
W weekly maintenance
item list, 12-3
operation guide, 12-3
i.