Page 1 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
Project:
Type: Qty:
Date: Customer:
M36LED Recessed
Custom colors are available, Please consult factory
Order Code: - - - - - - - - - - -
SR10,11,13 Philips Xitanium SR DALI
-
DC5 Lutron 5-Series (consult factory)
Series L36 Multi-Mount Form
Light Engine
CCT 30 3000K
35 3500K
40 4000K
Shielding LW LED Optimized white lens
MI Clear Lensw/microprism
NB LMO Symmetric
A2 LMO Asymmetric 20° Wall Washer
A5 LMO Asymmetric 5°Wall Grazer
MountingL36
SG Slot Grid (9/16”) (Wire Suspension or 1/4-20 stud)
SF1 Spackle Flange (1/2” Drywall)
SF2 Spackle Flange (5/8” Drywall)
SF3 Spackle Flange (After Drywall)
DC Decoustic Ceiling (up to 2” thick)
Nominal Fixture Length
01* 1 ft.
029 2 ft.
049 4 ft.
03 3 ft.
059 5 ft.
069 6 ft.
089 8 ft.
07 7 ft.
XX Runs (over 8’) & Configurations, round up to the nearest foot and replace the “xx” with the # (i.e. 09=09’ nominal)
Finish WH White
BK Black
SV Silver
SP Specify Premium Color
Voltage 120120 Volt
277277 Volt
LED WARRANTY
5YEAR
ARRA Compliant
27 2700K
Emergency Options
EC19 Emergency Circuit Wiring
V9022 Lit Inverted 90° Corner
IT9022 Lit “T” section
IX9022 Lit “X” section
L36R1 Continuous Flange (Flanged Endcaps)
L36R2 Continuous Flange(Flangless Endcaps)
BW LMO Batwing
TBS7 T-Bar Length w/1” 1/4-20 Stud
RC8 Rotating Crossbar (Ceilings 1/4 to 2” thick )
TS 1” 1/4-20 Stud
PM Perimeter Mount
TB7 T-Bar Length w/ suspension clips
EMN20,21 EM battery pack (Non-IC-rated)
IL9022 Lit Horizontal 90° Corner
19See page 8 for full details and restrictions 20120 or 277 Volt only 21Not available on lengths under 4’
MountingL36R1 or L36R2
9 Length intended to fit centered between the grid for SG, TB, TBS, PMT mountings.
PMT7 T-Bar Length Perimeter Mount
7L36R1 only 8Consult factory for lengths under 2’
DL14
Damp Location Rated
FS14 In-line Fuse
SS14 Separate Switching
CCEA15 CCEA approved
14See page 8 for full details and restrictions 15Not available with EMN option
Fixture Options
Configuration Options
UNV120 thru 277 50/60hz capable
22 See pages 10 and 11 for full details and restrictions
Individual fixtures, Runs and Configurations are supplied in nominal lengths to ensure full, even, illumination. See pages 2 thru 6 for additional details.
*1’ fixture only available with 1B35 light engine
Driver DML10,11 eldoLED SOLO-drive 0-10V (Logarithmic)
DMD10,11 eldoLED DALI (Logarithmic)
DCE10,11 Lutron Eco-System
DC310,11 Lutron 3-Wire
DC210,11,12 Lutron 2-Wire
10See page 7 for full details
11Not available for 1’ length
12120V only
13For use with E and P sensors only
DIM10 0-10V (Linear)
DM10,11 eldoLED SOLOdrive 0-10V (Linear)
Sensor Options
xE16,17 Enlighted
xP116,17 Philips Daylight
xP216,17 Philips Occ/Vac
xP316,17 Philips Occ/Vac/Daylight
xS116,18 Sensor Switch Daylight
xS216,18 Sensor Switch Occ/Vac
xS316,18 Sensor Switch Occ/Vac/Daylight
16 Minimum fixture length 2’. See page 9 for full details and restrictions.
17 For use with SR driver only
18 For use with DIM driver onlyReplace “x” with quantity
LU4,5 Light Up Lens
DR4,5 Drop Lens
4Not available with sensors
5I ndividual fixtures only. For Runs and Configurations, please consult factory. See page 8 for details
6 Not available with IL90, V90, or IX90 Configurations.
VC6 Specular Louver
VM6 Matte Silver Louver
VB6 Matte Black Louver
VW6 Matte White Louver
1B451,2,3 908lm/11.8W per foot
1B401,2,3 821lm/10.5W per foot
1B351 722lm/9.2W per foot
1B301,2 617lm/7.7W per foot
1B251,2 553lm/6.8W per foot
1B201,2 417lm/5.1W per foot
1 Values calculated from a 4’ fixture @4000K using LW Shielding and DIM driver. For additional information please see page 2.
2 Available starting at 2’ and up.3 Not available with Lutron.
or
BL Semi-Matte Black
347347 Volt (consult factory)
xSN nLight Enabled (consult factory)
EMR Remote Micro Inverter (consult factory)
EM Internal EM Battery Pack (consult factory)
Page 2 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Construction:
Housing - Continuous, low copper 6063-T6 extruded aluminum profile with aluminum endcaps, available as Individual fixtures (up to 12’) or Runs.
Flange - 9/16” (14mm) wide flange runs full lengths of both sides and is part of the main ex-truded body. Specify continuous flange (L36R1) or flush (L36R2) end cap. L36R2 does not work in T-Bar ceiling.
Geartray - Low copper 6063-T6 extruded alu-minum profile.
Shielding - Extruded, impact resistant acrylic lens:- LED optimized white lens (LW)- Clear lens with microprism inlay (MI)- “LMO” symmetric lens (NB)- “LMO” Asymmetric 5° wall grazer (A5)- “LMO” Asymmetric 20° wall washer (A2)- “LMO” Batwing (BW)- LED optimized Light Up Lens (LU)- LED optimized Drop Lens (DL)- Louvers: (VC) Specular, (VM) Matte Silver, (VB) Matte Black, (VW) Matte White “LMO” refers to the Selux proprietary LED optical system - Light Modulation Optics.
Mounting(s) - Spackle in (drywall), Slot grid, Decoustic, T-bar grid, Perimeter, Rotating Crossbar and Threaded Stud Mountings (see pages 3 thru 6 for details).
Standard Luminaire lengths - All standard luminaires are supplied in nominal lengths to ensure full, even, illumination. Runs and Con-figurations are available in approximately 1 1/2” increments starting at the nominal 8’ fixture length. ** Individual luminaires are not joinable in the field.
Exact length luminaires - Individual lumi-naires, Runs, and Configuration are available in exact lengths to meet your project needs. Please consult factory with you requirements. ** Lens luminance may soften at the very ends of the straight sections for exact length luminaires.
M36 Joiner(s) - Runs and Configurations are supplied in multiple housing that are joined together in the field using the supplied M36 Joiner System. This allows ease of installation and ensures a uniform appearance (see page 8 for detail).
Weight - 1.8 lb per foot
Electrical/Performance:
LED Light Engine - Brand-name mid-power LEDs create a high efficiency LED light engine able to provide a lumen maintenance of 96% at 25,000 hours and 93% at 60,000 hours @ 25ºC per TM-21 reports. Reported L70 greater than 60,000 hours.
Delivered Lumens - Due to LED manufacturer’s tolerances the listed output has a ±5% toler-ance. For outputs based on different shielding or CCT please see photometry section at the end.
CCT - Available in 2700K, 3000K, 3500K and 4000K, tolerance within a 3-step MacAdam ellipse.
CRI - Min. 90.
All Drivers - High efficiency, constant current, soft start, Electronic Class 2 with a PFC>0.90. For more detailed information on the available drivers please see page 7.
Sensors - Selux offers a variety of integral sensor options. For details and specifications, please refer to page 9.
Thermal Performance:
Ambient Operating Temperature - Luminaires suitable for maximum ambient temperature of35° C (95° F) for all drivers.
Luminaires are suitable for minimum ambient temperatures of:-40ºC (-40ºF) for DIM, DM, DML, and DMD drivers.-20ºC (-4ºF) for SR drivers.0ºC (32ºF) for DC2, DC3, and DCE drivers.
Luminaire Finish:
Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI.
All products undergo a five stage intensive pretreatment process where product is thor-oughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention.
Standard interior colors are White (WH), Black (BK), Semi-Matte Black (BL), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide.
Warranty:
5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the M36 series LED lumi-naire shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see “Selux Terms and Condition of Sale.”
Certifications and Compliance: NRTL - For Dry and Damp location (I.E. cULus; cCSAus)ARRA CompliantRoHS Compliant IC-Rated *
*EMN option is Non-IC-rated
2 13/16” (72mm)
1 5/16” (34mm)
1 7/16” (37mm)
2 13/16” (72mm)
1 5/16” (34mm)
2 7/16” (62mm)
1 13/16” (46mm) Light Up Lens Drop Lens LMO Lens Louver
LOUVERDIFFUSER1/4” (6mm)
1 7/16” (37mm)
Page 3 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
1. 1/4-20 Threaded rod to struture (supplied and installed by others).2. 14-20 Coupler hardware (supplied and installed by others).3. 1” 1/4-20 Stud (by Selux).4. Ø5/16” [Ø7mm] mounting hole. 5. Drywall/Sheetrock screw (Ref.)6. Drywall/Sheetrock (Ref.)7. 1/6” Plaster skimcoat (Ref.)8. Drywall/Sheetrock tape (Ref.) 9. Blocking to secure fixture (by others) 10. Electrical connection box, removable side cover for electrical
connection pre-installation, once installed the wiring is acces-sible from below the ceiling through the luminaire.
11. Brackets installed and shipped in the closed position by Selux. - For runs, rotate bracket to open position so the geartray can be removed to make the housing and wiring connections.
- After connections are made, rotate bracket back to the closed position (see installation instructions for full details).
- Brackets to be removed only after the luminaire is completely secured to the sheetrock through the spackle flange.
1/2” Spackle Flange Mounting (SF1)
Installation brackets
5/8” Spackle Flange Mounting (SF2)
Installation brackets
After Sheetrock Flange Mounting (SF3)
After drywall installation
Installation brackets
Spackle Flange Mounting (SF1, SF2 & SF3) - Dimensions
Nominal Length
“A” O.A.L. w/o Flange
“B” End Suspensions
* “C” (Ref.) Mid. Suspension
“D” Feed Location
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
01 (1 ft.) 1' - 5/16" 313 0' - 1 5/8" 41 0' - 9 1/8" 231 0' - 4 1/8" 105
02 (2 ft.) 2' - 1/4" 616 0' - 1 5/8" 41 1' - 9" 534 0' - 4 1/8" 105
03 (3 ft.) 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 2 1/8" 54
04 (4 ft.) 4' - 1/4" 1225 0' - 6 1/8" 156 3' 914 0' - 2 1/8" 54
05 (5 ft.) 4' - 10 11/16" 1491 0' - 6 1/8" 156 3' - 10 7/16" 1180 0' - 2 1/8" 54
06 (6 ft.) 5' - 10 5/8" 1794 0' - 6 1/8" 156 4' - 10 3/8" 1483 0' - 2 1/8" 54
07 (7 ft.) 7' - 1/4" 2140 0' - 6 1/8" 156 6' 1829 0' - 2 1/8" 54
08 (8 ft.) 8' - 1/4" 2444 0' - 6 1/8" 156 7' 2133 0' - 2 1/8" 54
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
1/2” Spackle Flange Mounting (SF1)
5/8” Spackle Flange Mounting (SF2)
After Sheetrock Flange Mounting (SF3)
Page 4 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
1. 9/16” Slot grid (shown as ref.) 2. Support wire to structure
(supplied and installed by others).3. 1/4-20 Threaded rod to structure
(supplied and installed by others).4. 1/4-20 Coupler hardware
(supplied and installed by others).5. 1” 1/4-20 Stud (by Selux).6. Ø5/16” [Ø7mm] mounting hole.
Slot Grid Mounting (SG) 9/16” Slot Grid Mounting (SG) (Wire Suspension or 1/4-20 Stud)
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Slot Grid Mounting (SG) - Dimensions
Nominal Length
“A” Housing Length
“B” End Suspensions
* “C” (Ref.) Mid. Suspension
“D” Feed Location
“E” Grid Spacing
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet
02 (2 ft.) 1' - 11 7/16" 595 0' - 1 5/8" 41 1' - 8 3/16" 513 0' - 4 1/8" 105 2’ Center to Center
04 (4 ft.) 3' - 11 7/16" 1205 0' - 6 1/8" 156 2' - 11 3/16" 894 0' - 2 1/8" 54 4’ Center to Center
05 (5 ft.) 4' - 11 7/16" 1510 0' - 6 1/8" 156 3' - 11 3/16" 1199 0' - 2 1/8" 54 5’ Center to Center
06 (6 ft.) 5' - 11 7/16" 1815 0' - 6 1/8" 156 4' - 11 3/16" 1504 0' - 2 1/8" 54 6’ Center to Center
08 (8 ft.) 7' - 11 7/16" 2424 0' - 6 1/8" 156 6' - 11 3/16" 2113 0' - 2 1/8" 54 8’ Center to Center
1. 1/4-20 Threaded rod to structure (supplied and installed by others).2. 1/4-20 Coupler hardware (supplied and installed by others).3. 1” 1/4-20 Stud (by Selux).4. Ø5/16” [Ø7mm] mounting hole.5. 1” wide alum. angle runs the entire length of fixture to block view into plenum
area from below fixture.6. Suitable for Decoustic® ceiling panel installations with panels up to 2” thick
(supplied and installed by others). Other ceiling systems possible, please consult factory. Decoustic® is a registered trademark of Decoustics Ltd. Corporation.
Decoustic Mounting (DC) Decoustic Mounting (DC) (Panels up to 2” thick)
Decoustic Mounting (DC) - Dimensions
Nominal Length
“A1” Housing Length
“B1” End Suspensions
* “C1” (Ref.) Mid. Suspension
“D1” Feed Location
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
01 (1 ft.) 1' - 5/16" 313 0' - 1 5/8" 41 0' - 9 1/8" 231 0' - 4 1/8" 105
02 (2 ft.) 2' - 1/4" 616 0' - 1 5/8" 41 1' - 9" 534 0' - 4 1/8" 105
03 (3 ft.) 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 2 1/8" 54
04 (4 ft.) 4' - 1/4" 1225 0' - 6 1/8" 156 3' 914 0' - 2 1/8" 54
05 (5 ft.) 4' - 10 11/16" 1491 0' - 6 1/8" 156 3' - 10 7/16" 1180 0' - 2 1/8" 54
06 (6 ft.) 5' - 10 5/8" 1794 0' - 6 1/8" 156 4' - 10 3/8" 1483 0' - 2 1/8" 54
07 (7 ft.) 7' - 1/4" 2140 0' - 6 1/8" 156 6' 1829 0' - 2 1/8" 54
08 (8 ft.) 8' - 1/4" 2444 0' - 6 1/8" 156 7' 2133 0' - 2 1/8" 54
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Page 5 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
T-Bar Mounting (TB) T-Bar with Stud Mounting (TBS)
T-Bar with Suspension Clips (TB) (9/16” or 15/16” grid)
T-Bar with 1/4-20 Stud (TBS) (9/16” or 15/16” grid)
Perimeter Mount T-Bar Length (PMT) (Recessed Wall Mounting)
Perimeter Mounting T-Bar Length (PMT)
1. Support wire to structure (supplied and installed by others).2. Spring steel suspension clips located approximately every 4 ft.
(supplied by Selux).3. 9/16” T-bar grid (shown as ref.)3a. 15/16” T-bar grid (shown as ref.)4. 1/4-20 Threaded rod to structure (supplied and installed by others).5. 1/4-20 Coupler hardware (supplied and installed by others).6. 1” 1/4-20 Stud (by Selux). 7. Ø5/16” [Ø7mm] mounting hole.
**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
T-Bar (TB & TBS) and Perimeter Mount (PMT) - Dimensions
Nominal Length
“A” O.A.L. with Flange
“A1” O.A.L. without Flange
“B” End Suspensions
“BB” (TB mtg.) Suspension
Clips
** “C” (Ref.) Mid. Suspension
“D” Feed Location
“E” Grid Spacing
“F” Wall Angle
Feet/Inch MM Feet/Inch MM Feet/Inch MM Quantity Feet/Inch MM Feet/Inch MM Feet Feet/Inch MM
*02 (2 ft.) 1' - 11 13/16" 605 1' - 10 15/16" 583 4 1/2” 114 4x 1' - 2" 355 0' - 1 1/8" 29 2’ Center to Center 1' - 10 11/16" 577
*04 (4 ft.) 3' - 11 13/16" 1215 3' - 10 15/16" 1193 0' - 6 1/8" 156 6x 2' - 10 3/4" 882 0' - 2 1/8" 54 4’ Center to Center 3' - 10 3/4" 1187
*05 (5 ft.) 4' - 11 13/16" 1519 4' - 10 15/16" 1497 0' - 6 1/8" 156 6x 3' - 10 3/4" 1187 0' - 2 1/8" 54 5’ Center to Center 4' - 10 11/16" 1491
*06 (6 ft.) 5' - 11 7/8" 1825 5' - 11" 1803 0' - 6 1/8" 156 6x 4' - 10 3/4" 1492 0' - 2 1/8" 54 6’ Center to Center 5' - 10 3/4" 1797
*08 (8 ft.) 7' - 11 13/16" 2434 7' - 10 15/16" 2412 0' - 6 1/8" 156 8x 6' - 10 11/16" 2101 0' - 2 1/8" 54 8’ Center to Center 7' - 10 3/4" 2406
*For other lengths consult factory
8. Steel Wall Bracket with provision for 1/4-20 fasteners (hardware to code by others).
9. 2” 1/4-20 Stud (by Selux).10. 1/2” x 1” Alum. wall angle allows a gap between flange
and wall to create shadow line allowing for uneveness of wall. Provision for #10 screws supplied approximately every 2 ft. (hardware to code by others).
Page 6 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Rotating Crossbar Mounting (RC) 1/4-20 Threaded Stud Mounting (TS)
Rotating Crossbars (RC) (1/4” to 2” thick ceiling)
1/4-20 Threaded Stud (TS) (1” Threaded Stud)
Perimeter Mounting (PM)
Perimeter Mount (PM) (Recessed Wall Mounting)
1. Rotating Crossbar intended for inaccessible ceilings, adjustable for ceiling thickness of 1/4” to 2”.
2. 1/4-20 Threaded rod to structure (supplied and installed by others).3. 1/4-20 Coupler hardware (supplied and installed by others).4. 1” 1/4-20 Stud (by Selux).5. Ø5/16” [Ø7mm] mounting hole.
**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Rotating Crossbar (RC), Threaded Stud (TS), and Perimeter Mountings (PM) - Dimensions
Nominal Length
“A” O.A.L. with Flange
“A1” O.A.L. without Flange
“B” End Suspensions
** “C” (Ref.) Mid. Suspension
“D” Feed Location
“E” Wall Angle
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
*01 (1 ft.) 1' - 1 3/16" 335 1' - 5/16" 313 0' - 1 5/8" 41 0' - 9 1/8" 231 0' - 4 1/8" 105 1' - 1/16" 307
02 (2 ft.) 2' - 1 1/8" 638 2' - 1/4" 616 4 1/2" 114 1' - 3 1/4" 388 1 1/8" 29 2' 610
03 (3 ft.) 3' - 1 3/16" 945 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 2 1/8" 54 3' - 1/8" 917
04 (4 ft.) 4' - 1 1/8" 1247 4' - 1/4" 1225 0' - 6 1/8" 156 3' 914 0' - 2 1/8" 54 4' 1219
05 (5 ft.) 4' - 11 9/16" 1513 4' - 10 11/16" 1491 0' - 6 1/8" 156 3' - 10 7/16" 1180 0' - 2 1/8" 54 4' - 10 7/16" 1485
06 (6 ft.) 5' - 11 1/2" 1816 5' - 10 5/8" 1794 0' - 6 1/8" 156 4' - 10 3/8" 1483 0' - 2 1/8" 54 5' - 10 3/8" 1788
07 (7 ft.) 7' - 1 1/8" 2162 7' - 1/4" 2140 0' - 6 1/8" 156 6' 1829 0' - 2 1/8" 54 7' 2134
08 (8 ft.) 8' - 1 1/16" 2466 8' - 1/4" 2444 0' - 6 1/8" 156 7' 2133 0' - 2 1/8" 54 8' 2438
*RC mounting, consult factory for lengths under 2’
6. Steel Wall Bracket with provision for 1/4-20 fasteners (hard-ware to code by others).
7. 2” 1/4-20 Stud (by Selux).8. 1/2” x 1” Alum. wall angle allows a gap between flange and
wall to create shadow line allowing for uneveness of wall. Provision for #10 screws supplied approximately every 2 ft. (hardware to code by others).
Page 7 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Driver Quantity
1 ft. 2 ft. 3 ft. 4 ft. 5 ft. 6 ft. 7 ft. 8 ft. 9 ft. 10 ft. 11 ft. 12 ft. RUN
DIM, DM, DML, DMD, and SR drivers 1 1 1 1 1 1 2 2 2 2 3 3 Approximately 1 driver per 4 ft.
DC2, DC3, & DCE drivers N/A 1 1 1 2 2 2 3 3 3 3 3 Consult Factory
Drivers:
0-10V linear dimming (DIM)Luminaires supplied with drivers offering the capability of either normal switched operation of 0-10V dimming for linear dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to 1%. (Due to size con-straints, 1’ luminaires are supplied with a driver from a different manufac-turer than 2’ and above luminaires. For details, please consult factory).
eldoLED SOLOdrive 0-10V linear dimming (DM)Luminaires supplied with SOLOdrive 0-10V dimming driver for linear dim-ming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.
eldoLED SOLOdrive 0-10V logarithmic dimming (DML)Luminaires supplied with SOLOdrive 0-10V dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.
eldoLED SOLOdrive DALI dimming (DMD)Luminaires supplied with SOLOdrive DALI dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.
* For control recommendations for eldoLED drivers, please consult eldoLED.
LUTRON 2-wire dimming (DC2)Luminaires supplied with Hi-Lume 2-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.
LUTRON 3-wire dimming (DC3)Luminaires supplied with Hi-Lume 3-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.
LUTRON Ecosystem dimming (DCE)Luminaires supplied with Hi-Lume EcoSystem (4 wire, digital link) dim-ming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.
* For control recommendations and system layout for Lutron drivers, please contact Lutron.
Philips Xitanium Sensor Ready DALI dimming (SR)Luminaires supplied with Xitanium SR dimming driver programmed for Constant Current Reduction (CCR). Minimum dimming level down to 5%. For use with E and P sensors only.
*For inrush and control current, please refer to the driver manufacturers’ spec sheets.
Wiring Diagrams Sensor Wiring Diagrams
ENLIGHTEDOR PHILIPSSENSOR
ELDO 0-10V
SENSORSWITCH
PHILIPS XR
SR (+)SR (-)
(+)(-) 0-10V AUX (+)
AUX (-)
standard0-10V linear (DIM) 0-10V linear eldoLED SOLOdrive (DM)0-10V logarithmic eldoLED SOLOdrive (DML)DALI eldoLED SOLOdrive (DMD)Philips SR DALI (SR)
DIM, DM, DML, DMD & SR
DALIDALI
Page 8 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the hot wire for each feed. (supplied with an 8A slow burn fuse).
Damp Location (DL) - Luminaires are suitable for use in damp location(s). Examples of such locations include protected areas under canopies, marquees, roofed porches, and similar locations where the fixture(s) are protected from direct contact with rain, snow, or excessive moisture (such as ocean spray). Interior locations include areas subject to moderate degrees of moisture, such as basements and certain barns and cold storage buildings. All solder points on LED boards are conformal coated. The phosphor layer of the LEDs is free of coating to avoid hazing.
*For Damp Location with sensors, please consult factory.
Separate Switching (SS) - Luminaires available with separately switched 4’ (nominal) sections starting at 7’ and up. Luminaire is in-tended to be wired to the same panel/breaker (not intended for Emer-gency use).
- To specify this option, the number of separately switched sections and locations of these sections must be provided at time of order.
*If the project requires different separate switching than outlined above please consult the factory.
*For Separate Switching with sensors, please consult factory.
EMN (Emergency Battery Pack)* - Emergency battery pack is avail-able starting at the 4’ nominal length and up in 2’ nominal sections. The battery pack is housed in a box on the top of the luminaire and is fully accessible from below the ceiling.
- For individual luminaires, the lit section will be located on the feed end of the fixture. If a different location is needed please consult the fac-tory.
- For Runs, please specify location of lit section (in 2’ nominal sections).
*Luminaires with EMN option are Non-IC-rated
*For EMN with sensors, please consult factory.
Emergency Circuit (EC) - Luminaires with EC option compliant to UL 924 listed emergency luminaire. EC luminaires are intended to be wired to separate panels/breakers for emergency use.
- For 1’ to 6’ nominal luminaires, the entire fixture is wired for operation on emergency circuit.
- For 7’ and up nominal luminaires, the first 4’ nominal length is wired for operation by a separate EM circuit by default to meet the required “Life Safety Code” (NFPA 101).
*If a different configuration is needed please consult the factory.
*For EC with sensors, please consult factory.
90° Elbow on top of the housing (7/8" feed hole)
3/8" flexible metal conduit (6' long)
6" leads
Straight fitting
Flex Whip - standard for recessed fixtures Joiner System - standard for Runs and Configurations
Fixture extrusion
Joiner extrusion
Recommended #2 Phillips drive
Fixture extrusion
Additional view
EMN Model # Input Operation Time
Lumen Output
CCT Shielding
Bodine BSL310 4W Max. 90 Min. *785 lm **4000K *LW
EMN pack
3” (76mm)
2’ (610mm)
Light Up or Drop Lens Detail
Light Up or Drop Lens
Housing
Light Up Lens 6mm Drop Lens 37mm
*Lumen output is fixed and the same for all light engines** See page 13 for CCT and shielding multiplier
Page 9 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Sensor Ordering Chart
Quantity Sensor Settings*
x Number of Sensors E Enlighted FS-D22
P Philips Easy Sense SNS102
S Sensor Switch MSD EZ
1 Daylight
2 Occupancy/Vacancy
3 Daylight/Occupancy/Vacancy
* Settings not available with Enlighted
Lens
3” (76mm)
Qty 1 Sensor - Beginning
1 7/16” (37mm)Qty 3+ Sensor - For spacing between sensors, please consult the sensor manufacturer.
Beginning of Run
Occupancy Vacancy Daylight Harvesting Driver Compatibility
Enlighted FS-D22 (E) See Enlighted’s website for full capabilities SR
Philips EasySense SNS102 (P) √ √ √ SR
Sensor Switch MSD EZ (S) √ √ √ DIM
Factory Presets - Sensors come from the sensor manufacturer with factory presets for each of the settings in above chart. Please see sensor manufacturers’ spec sheets for details on presets and re-programming.
Commissioning - Commissioning of sensors and installation by others. Contact sensor manufacturer for details and costs associated with commissioning the system prior to specification of sensors.
Fixture LengthLit Section*
Enlighted FS-D22 (E)Occupancy/vacancy, daylight harvesting, plus the Internet of Things (IoT) data collection and reporting. For full details, please see FS-D22 spec sheet on the Enlighted website. Must be paired with Philips Xitanium SR driver (SR driver selection). Commissioning by Enlighted. *Please contact Enlighted for complete details prior to specifying. *Sensor can control up to 4 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.
Philips EasySense SNS102 (P)Occupancy/vacancy and daylight harvesting. Sensor can be programmed on-site via NFC or IR using Android app only, by others. For full details, please see the SNS102 spec sheet on the Philips website. Must be paired with Philips Xitanium SR driver (SR driver selection). Wall dimming via wireless wall switch from Philips/Illumra (www.illumra.com/easysense). **Please contact Philips for complete details prior to specifying. *Sensor can control up to 10 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.
Sensor Switch MSD EZ (S)Occupancy/vacancy and daylight harvesting. For full functionality and programming options, select settings option 3. If a different settings option is selected, other settings may be unavailable. For full details, please see MSD EZ spec sheets on the Sensor Switch website. Must be paired with eldoLED 0-10V driver (DIM driver selection). Manual control of dimming not available with MSD EZ sensor. *Please contact Sensor Switch for complete details prior to specifying.*Sensor can control up to 30 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.
Standard Sensor Placement - for other placement options, please consult factory. For functionality and limitations, please see sensor details above.
Aluminum Sensor Plate -to be painted same as fixture unless specified otherwise
Qty 2 Sensor - Beginning and End (9’ fixtures and longer)
Notes: 1. For spacing between sensors, please consult the sensor manufacturer. 2. Exact sensor placement and coverage will be defined by approved factory drawing. 3. Sections controlled by sensors may not be symmetrical - consult factory for layout.
* Lit section will be the fixture length minus 3” for sensor plate.
Page 10 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Listed below are the minimum lengths and details for standard shapes. These standard shapes can be combined with each other and/or the standard luminaire lengths, ensuring full even illumination. If you have any questions please consult the factory.
The minimum standard lengths for “L” shapes:- IL90 or V90 open shapes is 4’ x 4’ nominal (example, leg, 90, leg)- IL90 or V90 closed shapes is 6’ x 6’ nominal (example, 90, leg, 90)( Exception is that the IL90 & V90’s can be joined directly to provide a 4’ x 4’ nominal shape).
*For sensors in configurations, please consult factory.
Standard Recessed (L36) shapes/configurations:
The minimum standard lengths for “T” & “X” shapes:- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side- IX90 = 8’ nominal for either direction
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Project Specific Recessed (L36) shapes/configurations:
Recessed (L36) Lit Corner and Section - Dimensions
IL90 V90 IT90 IX90
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
“A” w/Flange (Outside) 2' - 13/16" 631
“A1” Housing (Inside) 1' - 11 3/8" 594
“B” Housing (Outside) 2' - 2 5/16" 669
“B1” Housing (Inside) 1' - 11 1/2" 597
“C” Housing 2' - 13/16" 631
* “C1” Ref. 2' - 1/8" 612
“D” Housing 4' - 3/16" 1224
* “D1” Ref. 2' - 1/8" 612
“E” Housing 4' - 3/16" 1224
* “E1” Ref. 2' - 1/8" 612
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
"B" Housing
"B"
Hou
sing
"B1" Housing
"B1"
Hou
sing
"E" Housing
"E"
Hou
sing
"E1"
Ref
.
"E1" Ref."C" Housing
"D"
Hou
sing
"D1"
Ref
.
"C1" Ref.
"A" Housing
"A"
Hou
sing
"A1" Housing
"A1"
Hou
sing
IL90 - Lit Horizontal corner
V90 - Lit Inside corner
IT90 - Lit "T" section IX90 - Lit "X" section
BottomView
BottomView
BottomView
SideView
Page 11 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Listed below are the minimum lengths and details for standard shapes. These standard shapes can be combined with each other and/or the standard luminaire lengths, ensuring full even illumination. If you have any questions please consult the factory.
The minimum standard lengths for “L” shapes:- IL90 or V90 open shapes is 4’ x 4’ nominal (example, leg, 90, leg)- IL90 or V90 closed shapes is 6’ x 6’ nominal (example, 90, leg, 90)( Exception is that the IL90 & V90’s can be joined directly to provide a 4’ x 4’ nominal shape).
*For sensors in configurations, please consult factory.
Standard Recessed (L36R1/2) shapes/configurations:
The minimum standard lengths for “T” & “X” shapes:- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side- IX90 = 8’ nominal for either direction
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Project Specific Recessed (L36R1/2) shapes/configurations:
Recessed (L36R1/R2) Lit Corner and Section - Dimensions
IL90 V90 IT90 IX90
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
“A” w/Flange (Outside) 2' - 1 5/16" 643
“A1” Housing (Outside) 2' - 13/16" 631
“B” w/Flange (Inside) 1' - 10 7/8" 581
“B1” Housing (Inside) 1' - 11 3/8" 594
“C” Housing (Inside) 1' - 11 1/2" 597
“C1” Housing (Outside) 2' - 2 5/16" 669
“D” w/Flange 2' - 1 5/16" 643
“D1” Housing 2' - 13/16" 631
* “D2” Ref. 2' - 1/8" 612
“E” Housing 4' - 3/16" 1224
* “E1” Ref. 2' - 1/8" 612
“F” Housing 4' - 3/16" 1224
* “F1” Ref. 2' - 1/8" 612
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Page 12 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Photometry Photometry
259
517
776
1034
1
2
Maximum Candela = 1034 Located At Horizontal Angle = 90, Vertical Angle = .5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
LW Optics / 36W LED / 4000K CCT
447
893
1340
1786
1
2
Maximum Candela = 1786 Located At Horizontal Angle = 90, Vertical Angle = 9.5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
MI Optics / 36W LED / 4000K CCT
Catalog #: L36-1B35-40-MI-X-04-XX-UNVReport #: 11684969.03 Delievered Lumens: 2950 Input Watts: 36.64WEfficacy: 81 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 1786 @ 9.5° from VerticalSpacing Criterion (0-180): 1.22 Spacing Criterion (90-270): 1.02 Spacing Criterion (Diagonal): 1.08
Catalog #: L36-1B35-40-LW-X-04-XX-UNVReport #: 11684969.01 Delievered Lumens: 2887 Input Watts: 36.74WEfficacy: 79 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 1034 @ .5° from VerticalSpacing Criterion (0-180): 1.24 Spacing Criterion (90-270): 1.24 Spacing Criterion (Diagonal): 1.38
381
761
1142
1522
1
2
Maximum Candela = 1522 Located At Horizontal Angle = 90, Vertical Angle = 6.5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
NB Optics / 36W LED /4000K CCT
Catalog #: L36-1B35-40-NB-X-04-XX-UNV Report #: 11684969.05 Delievered Lumens: 3529 Input Watts: 36.67WEfficacy: 96 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 1522 @ 6.5° from VerticalSpacing Criterion (0-180): 1.22 Spacing Criterion (90-270): 1.14 Spacing Criterion (Diagonal): 1.26
Page 13 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Photometry
A2 Optics / 36W LED / 4000K CCT
A5 Optics / 36W LED / 4000K CCT
Catalog #: L36-1B35-40-A5-X-04-XX-UNVReport #: 11684969.06 Delievered Lumens: 3660 Input Watts: 36.73WEfficacy: 95 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 2219 @ 3° from VerticalSpacing Criterion (0-180): 1.10 Spacing Criterion (90-270): 0.84 Spacing Criterion (Diagonal): 1.00
BW Optics / 36W LED / 4000K CCT
Catalog #: L36-1B35-40-BW-X-04-XX-UNVReport #: 11684969.04 Delievered Lumens: 3193 Input Watts: 36.65WEfficacy: 87 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 1388 @ 40.5° from VerticalSpacing Criterion (0-180): 1.28 Spacing Criterion (90-270): 2.36 Spacing Criterion (Diagonal): 1.98
347
694
1041
1388
1
2
Maximum Candela = 1388 Located At Horizontal Angle = 90, Vertical Angle = 40.5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
555
1110
1664
2219
12
Maximum Candela = 2219 Located At Horizontal Angle = 90, Vertical Angle = 3# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
621
1241
1862
2482
1
2
Maximum Candela = 2482 Located At Horizontal Angle = 0, Vertical Angle = 20# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
Catalog #: L36-1B35-40-A2-X-04-XX-UNVReport #: 11684969.07 Delievered Lumens: 3647 Input Watts: 36.69W Efficacy: 99 Power Factor: 0.990 Total Harmonic Distortion: 4.63 CCT: 3982KCRI: 83.9Max Candela: 2482 @ 20° from VerticalSpacing Criterion (0-180): 1.66 Spacing Criterion (90-270): 1.24 Spacing Criterion (Diagonal): 1.44
Page 14 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Photometry
LU Optics / 36W LED / 4000K CCT
Catalog #: L36-1B35-40-LU-X-04-XX-UNVReport #: 11684993.02 Delievered Lumens: 3102 Input Watts: 38.04WEfficacy: 82 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 1002 @ 1° from VerticalSpacing Criterion (0-180): 1.26 Spacing Criterion (90-270): 1.26 Spacing Criterion (Diagonal): 1.38
DR Optics / 36W LED / 4000K CCT
Catalog #: L36-1B35-40-DR-X-04-XX-UNVReport #: 11684993.01 Delievered Lumens: 3422 Input Watts: 37.95WEfficacy: 90 Power Factor: 0.989 Total Harmonic Distortion: 10.1 CCT: 3896KCRI: 95.7Max Candela: 600 @ 26.5° from VerticalSpacing Criterion (0-180): 1.26 Spacing Criterion (90-270): 1.62 Spacing Criterion (Diagonal): 1.62
150
300
450
600
1
2
Maximum Candela = 600.1 Located At Horizontal Angle = 90, Vertical Angle = 26.5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
251
501
752
1002
1
2
Maximum Candela = 1002 Located At Horizontal Angle = 0, Vertical Angle = 1# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
Page 15 of 15 (Rev. 09/2017)
M36LED Recessed_v[1B]3.2
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M36LED Recessed
Photometry
CCT and CRI multipliers apply to the photometry, IES files, and per foot values listed on page one (light engine).
Light engine multiplier supplied for per foot values listed on page one (light engine).
4000K3500K3000K2700K
LightEngine Lumens Wattages1B45 1.258 1.2851B40 1.137 1.1401B35 1.000 1.0001B30 0.855 0.8381B25 0.766 0.7401B20 0.578 0.552
LWMINBA2A5BWLUDRVWVMVCVB 0.000
L36LEDDirectPhotometryMultiplierTable
CCTMultiplier
LightEngineMultiplier
1.0000.9720.9630.931
1.0221.2221.2681.2631.1061.0741.1850.0000.0000.000
LensMultiplier1.000