123.6in3140mmOperating
Height
45.2in1147mm
Conveyor Discharge
33.7in856mm
Table Height
141.8in3601mm
Operating Width
134.4in3415mmOperating
Depth
3.5in[89mm]
(Recommended
All dimensions based on stackup of sheetmetal, subject to variation of 1/2" ( 13 mm)
Operating Dimensions
Shipping Dimensions
Coming soon. Please contact [email protected] if this information is needed urgently
UMC-750 (2020) Installation DimensionsMachine Layout DrawingRevision APage 1 of 6Feb 1 2020
63.4in1611mmElectrical
32.3in820mm
Air
3.0in76mm
Electrical
27.4in695mm
Electrical
36.2in920mm
Air
17.3in439mm
Air
Front of machine
31.7in806mm
31.7in806mm
(3x)
34.0in864mm
34.0in864mm
39.3in999mm
23.3in593mm
30.2in768mm
30.2in768mm
17.6in446mm
(Ref)
60.8in1544mm
(Ref)
22.3in566mm
(Ref)
32.9in836mm
(Ref)
17.2in438mm
(Ref)
FRONT
All dimensions based on stackup of sheetmetal, subject to variation of 1/2" ( 13 mm)
Rear ViewTop View
Anchor Hole DetailØ1.0in [25mm]
3.5in [90mm]
Note - Machine must be placed on onecontinous concrete slab. Slab shiould extend 12in [305mm] beyond anchor holes in all directions
UMC-750 (2020) Utilities & AnchoringMachine Layout DrawingRevision APage 2 of 6Feb 1 2020
Anchor Pattern
Air & Power
123.6in3140mmMaximumoperating
height
73.4in1865mm
103.0in2615mm
Maximum Øtool
45.1in1147mm
24.5in623mm
UMC-750
253.7in6445mm
Maximum service width
76.0in1930mm
Clearance to removechip conveyor
141.8in3601mm
Operating Width
36.0in914mm
Electricalcabinet
door swing
133.4in3387mm
Operating depth
28.5in724mm
18.2in462mm
13.2in336mm
8.3in210mm
75.4in1916mm
Roof
50.9in1294mm
Roof
12.3in313mm
24.4in619mm
100.9in2562mm
119.0in3022mmSpindlehousing
73.5in1867mmMaximum
Y Axisprotrusion
101.6in2582mm
32.7in830mm
25.7in652mm
Window Opening(Approximate)
23.0in584mm
98.1in
2493mmSeeNote
**
All dimensions based on stackup of sheetmetal, subject to variation of 1/2" ( 13 mm)
All dimensions based on stackup of sheetmetal, subject to variation of 1/2" ( 13 mm)**Height reduction achieveable with no leveling feet or bolts, and removing roof, X axis way covers, spindle shroud, fan, and support brackets
UMC-750 (2020) BreakdownsMachine Layout DrawingRevision APage 3 of 6Feb 1 2020
Width Breakdown
Height Breakdown
.42in[10.7mm]
.64in[16.3in]
.63in[16.0mm]
1.09in[27.7mm]
8.18in208mm
MinimumMounting Ø
9.920in252mm
19.7in500mmPlatter
2.480in63.0mm
T-Slot CL to CL (6x)
4.0in101mm
21.5in546mm
Z Height at Tool Change
4.5in114mm
Drop Down DuringTool Change
T-Slot Detail
Note (10x) Phantom holes are not available to use for part fixturing1.It is possible to route a hydraulic or pneumatic hose thru the trunnion to 2.center of the platter to accomodate automatic workholding with the following considerations -
1. A sealed rotary union must be used. The center bore leads directly to the trunnion cavity. An unsealed union will allow coolant and chips to penetrate the interior and cause damage 2. From the factory there is a plug installed. The plug should be knocked out thru the bottom of the trunnion, or drilled thru to accomodate the sealed union3. The hoses should be sufficiently retained such that they do not interfere with any other components
Note - See solid model for tool changer maximum interference sweep
UMC-750 (2020) Table & Tool ChangerMachine Layout DrawingRevision APage 4 of 6Feb 1 2020
Tool Changer
Table
4.0in[102mm]Min Z
Clearance
24.0in610mm
MaximumZ Clearance
20.0 in[508mm]Z Axis travel
Z Axis Clearance at B0
+120 Max -35 Min
Top Of Table
4.6in116mm
6.2in157mm
19.7in500mm
8.2in207mm
4.75in121mm
4.0in101.6mm
1.0in25.4mm
2.0in50.8mm
Center of Rotation
(3x) 1/2-13 UNC 0.70in [18mm]
Vise Mounting Holes
(Custom holes can be drilledanywhere on this surface
.70in [18mm] Max)
20.0in508mmY AxisTravel
30.0in762mm
X Axis Travel
13.0in330mm
17.0in432mm
10.0in254mm
Table Rotation
UMC-750 (2020) Axes ClearancesMachine Layout DrawingRevision APage 5 of 6Feb 1 2020
Z-Axis Clearance
X&Y-Axis Clearance
12.75in324mm
Z Axis Clearance available at B90 for Side Mounted Vise
26.0in[660mm]Maximum
recommended Swing Ø*
(Tool Length + Workpiece Height)≤ 23.0in [585mm]
Maximum Combined Height*
20.0in508mm
30.0in762mm
19.0in483mm
8.4in212mm
Side Vise pad
7.6in192mm
Pad size andX Axis travel
available at B90for side mounted vise from bottom
of platter
Clearance at B90
*Note - Maximum height and swing apply to B0 orientation only. Large workpieces, including ones within the stated work envelope, may interfere with other mahcine components as the tilt angle increases. If your part is larger than 20.0in [500mm] diameter or taller than 18in [460mm] it is recommended to review your application's suitability with your local HFO Applications team
UMC-750 (2020) B90 & Work EnvelopeMachine Layout DrawingRevision APage 6 of 6Feb 1 2020
162" (4115 mm)
36"(914 mm)
(940 mm)37"
(965 mm)38"
13" (330 mm)
Max
126"(3200 mm)
183" (4648 mm) Max
5X Anchor Kit(1600 mm)
63"
(279 mm)11"
(660 mm)26"
(660 mm)26"
21" (533 mm)
89" (2261 mm)
87" (2210 mm)
113" (2870 mm)
81"
Other Side(2057 mm)
Minimum distance required to remove conveyor from mill 85" (2159 mm)
Note:
1 Electrical Connection
2 Air Connection
Note:Foundation must extend at least12" (305 mm) from bored holes.
3.5" (89 mm)
Machine Layout Drawing - UMC-750/SS/P (2012-2019)
Operating Dimensions
Anchor Pattern
Leveling Pads
Note:The roof is a standard feature as of Q1 2018
34.5"
Min(876 mm)
Height
120"(3048 mm)
Max
2
1
(1702 mm)
149" (3785 mm)
112" (2845 mm)
67"(2870 mm)113"
Door
Machine Front
Open
Front
Base Casting
Foundation Line
5X 1-1/2 x 8-1/2" DP(5X 38 x 216 mm DP)
1
2Other Side
23"(584 mm)
UMC-750/SS/P Revision PPage 1 of 5
December 2017
' aoon----
113" (2870 mm)
90" (2286mm)
Spin<lle Head as Shipped Machine Clearance Dimensions
Ii-_.,_ ______ 33" (838 mm)
..0---0
/0_,,,
',t\\
9 /
' -CY /'\ 'e-
14" (356 mm) . \_
14.75" (374.7 mm)
" 012 (305 mm)
UMC-750P Table Dimensions
1.7" (43mm)
2X .4" (10mm)
@ @ 3.2"
(81 mm)
Detail C
1.00" (25.4 mm)
.4" (10 mm)
+ 'l) 1.9685 + .0005 I -0"
(50 +.013 / -0 mm)
(l'.12.160 +.005 / -0." L...£...--L.--L...U (54.86 +0.13/-0. mm)
Section B
------ 19.7" (500 mm) -----i
7
Rear sheet metal enclosure removed (For shipping)
.4"(10 mm)
.630 - .635" (16 mm)
.64" (16 mm)
Detail A
J__ 6X 2.48" (63 mm)
,--
3" (76 mm)
.4" (10 mm)
' .630 - .635" (16 mm)
.64" (16 mm) ---l
1.06" (27 mm)
19.7" (500mm)
1.06" (27 mm)
UMC-750/SS Table Dimensions Detail A (7X) UMC-750/SS/P Revision P
Page 2 of 5December 2017
L
11"(279mm) Table to Inside of Sheet Metal
30" (762 mm) � Max X-Axis Travel I I
I& I
�
39• (991 mm) Door Opening
Notes:
1. Spindle head at max X and Y travels.
2. Measurements are from the edge ofmill table to nearest obstruction (ie. enclosure, door, etc.).
&robe
& (3X) Lifting Points
10.4" (264 mm}
----,-4 20· (508 mm)
Max Y-Axis Travel
(/)27" (686 mm) Max Part Swing
on C-Axis
Max Travels X 30in 762mm y 20in 508mm z 20in 508mm B -35, +110 deg
Machine Travels C 360 deg
8-Axis Work Envelope
Max part/wor1<hokling capacity as defined by full B-axis rotation
(Sheet metal removed for clarity)
Max Weight Capacity 660 lb (300 kg}
. -. --
Enclosure Work Space UMC-750/SS/P Revision P
Page 3 of 5December 2017
20" (508 mm) Spindle Head Clearance at max B-Axis Travels
14" (355mm)
To Center of B-Axis Rotation Max B-Axis rota ion is t45 •
A-Axis
_J 6" (152.4 mm)
Max Part Radius
11" (279 mm) Max X-Axis Travel at center of spindle
�-----24.5" (622 mm) ___ _.,,.. Max Part Lengtn
Tnis view snows tne spindle nead clearance witn a 2" (50.8 mm) long tool, wnicn is 3" (76.2 mm) above tne minimum clearance
2.00" (50.8 mm)
UMC-750P Table/Rotary Dimensions
UMC-750/SS/P Revision PPage 4 of 5
December 2017
--- --
(/)27" 0 -_,,...,,--- ---(686 mm)�;:,,-----
I I
\
, /
I//I I
I ,l I
I
I ct
I
4.2" (107mm)
12.a· (325mm)
Notes:
1. Double arm swingsdown 4.5" (114 mm).
Double armswing diameter.
Overall length of arm.
40 Taper 40+1 Side-Mount Tool Changer Double Arm Work Envelope
8.9" (226mm)
Programmable Coolant (P-Cool)
'*The UMC-750P's table is 1" (25.4 mm) shorter than the standard table, dearance is 5-25" (127-635 mm)
24" (610mm)
MaxZ-Axis Clearance to Table ..
20· (508mm)
Z-Axis Travel
4" (102 mm) Min ..
ct
Spindle Head Clearances
©
(/)5.2"
(132 mm)
6.5" (165mm)
9.4" (239 mm)
UMC-750/SS/P Revision PPage 5 of 5
December 2017