Main Technical Speciﬁ cations Trenchers for Pipeline ......0500 oil level mod.41t-140-sae oil...

MODEL GROSS POWER ENGINE WEIGHT

RANGE

ROCKSAWDIG DEPTH /DIG WIDTH

CHAINSAWDIG DEPTH /DIG WIDTH

BUCKET WHEEL

DIG DEPTH /DIG WIDTH

ROCK HAWGDIG DEPTH / DIG WIDTH

775DT225 hp

(168 kW)Caterpillar

C6.6 ACERT

34,171-55,000 lbs

(15.500-24.947 kg)

6’ 6” (198 cm)

18”-30” (46-76 cm)

975325 hp

(242 kW)Caterpillar

C9 ACERT

55,116-72,752 lbs

(25.000-33.000 kg)

4’-10’ (122-305 cm)

12”-36” (30-91 cm)

1075325 hp

(242 kW)Caterpillar

C9 ACERT

87,000-92,000 lbs

(39.462-41.730 kg)

0-7’ (0-213 cm)

20”-40” (51-102 cm)

1085325 hp

(242 kW)Caterpillar

C9 ACERT

85,000-95,000 lbs

(38.556-43.092 kg)

4’-8’ (122-244 cm)

18”-28” (45-71 cm)

1150XHD440 hp

(328 kW)Caterpillar

C13 ACERT

110,231-132,278 lbs

(50.000-60.000 kg)

6’-12’(183-366 cm)

18”-42” (45-107 cm)

1175XHD440 hp

(328 kW)Caterpillar

C13 ACERT

126,000-141,000 lbs

(57.152-63.956 kg)

3’-9’ (91-274 cm)

30”-54” (76-137 cm)

1375540 hp

(403 kW)Caterpillar

C15 ACERT

160,000-175,000 lbs

(72.575-79.379 kg)

3’-9’ (91-291 cm)

36”-66” (91-168 cm)

1475630 hp

(470 kW)Caterpillar

C18 ACERT

169,756-242,509 lbs

(77.000-110.000 kg)

8’-16’ (244-488 cm)

32”-48” (81-122 cm)

1575630 hp

(470 kW)Caterpillar

C18 ACERT

210,000-248,000 lbs

(95.255-112.491 kg)

3’8”-10’ (112-304 cm)

34”-72” (86-183 cm)

1675760 hp

(567 kW)Cummins

QSK 19

249,124-308,649 lbs

(113.000-140.000 kg)

8’-24’ (244-732 cm)

28”-72” (71-183 cm)

M3350 hp

(261 kW)Caterpillar

C9 ACERT

95,000-135,000 lbs

(43.091-61.235 kg)

6’-12’ (183-366 cm)

26”-40” (66-102 cm)

M5440 hp

(328 kW)Caterpillar

C13 ACERT

140,000-161,000 lbs

(63.502-73.028 kg)

6’-16’ (183-488 cm)

30”-42” (76-107 cm)

Main Technical Specifi cations

Trenchers for Pipeline construction

powered by

0250

Dirt series 775DT BW

Ed. 2013/11

Tesmec S.p.A.HeadquartersVia Zanica, 17/O - 24050 Grassobbio (BG) - ItalyTel: +39.035.4232911 - Fax: +39.035.335664

PICTURES & DRAWINGS CAN BE DIFFERENT ACCORDING TO TECHNICAL SPECIFICATIONS - UPDATING PROGRAMME VARIATIONS WITHOUT NOTICE ARE POSSIBLE

Keep you updated on: www.tesmec.comTesmec USA Inc.12520 East FM 917 - Alvarado, Texas 76009 - USATel: +1.817.4732233 - Toll free: 800.8515102Fax: +1.817.4739742

BUCKET WHEEL VERSION OF THE 775DT CS, THIS LIGHT BUCKET-TRENCHER CAN GRANT AN EVEN AN EVEN HIGHER PRODUCTIVITY IN TERMS OF METERS-YARDS PER HOUR. TRENCHTRONIC EQUIPPED, THIS MACHINE HAS BEEN SPECIALLY DEVELOPED TO BE EMPLOYED IN “DIRT” EXCAVATION; ITS COMPACT DIMENSIONS AND WEIGHT MAKE THE 775DT BW VERY EASY TO USE AND TRANSPORT.

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

6'-

6"

[19

8cm

]9

'-1

1"

[30

2cm

]

34'-2" [1041cm]

11'-1.9" [340cm]

5'-10"[178cm]

2'-

1"

[6

3cm

]

10

'-2

" [

31

0cm

]

2'-7" Track [80cm]

8'-4" Tracks [255cm]

32'-7"[993cm]

9'-8" [296cm]

MIN 18" [46cm]MAX 30" [76cm]

18

°

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

seg 22

se g 2 2

Trencher

TESMEC

Trencher

TESMEC

0250Keep you updated on: www.tesmec.com


Tesmec S.p.A.HeadquartersVia Zanica, 17/O - 24050 Grassobbio (BG) - ItalyTel: +39.035.4232911 - Fax: +39.035.335664Ed. 2013/11

Tesmec USA Inc.12520 East FM 917 - Alvarado, Texas 76009 - USATel: +1.817.4732233 - Toll free: 800.8515102Fax: +1.817.4739742

Dirt Series 775DT Bucket WheelSpecification

Trenching DimensionsMax depth.......................................6’ 6” (198 cm)Widths range..........................18”-30” (46-76 cm)Note: ask to Tesmec Trenchers Technical Department for the max width at max depth confi guration

Operating and Transport WeightEstimated weight......................47,000-52,000 lbs ......................(21.318-23.587 kg)Ground pressure................................5.75-6.36 psi .......................(0.39-0.43 kg/cm2)Note: dependent on confi guration and options

Trencher DriveHydrostatic: one pump and two motors Infinitely variable digging wheel speeds...0-12 rpm Dirt cutters: spade-type teeth Fixed crumbshoe: with manual quick disconnectWheel truck assemblies:• Six assemblies, two upper and one lower with

standard 10” (25.4 cm) diameter wheels • Modular designed “Truck-spindle and bearings”

are the same on all assemblies Headshaft assembly:• Alloy steel shaft with keyway, hubs and

tapered keys for multiple bucket setups• Hardened, reversible split drive sprockets

Transport DimensionsLength........................................34’ 2” (1.036 cm)Width............................................8’ 4” (255 cm)Height over cab and ..................10’ 2” (310 cm)with 3 bottom buckets removed

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum..............53 gpm (201 l/min)Pressure setting......................2.600 psi (180 bar)Oil tank capacity................................77 gal (290 l)

Cross ConveyorPressure and flow compensated pump with dual hydraulic drive motorsReversible and shiftableBelt speed infinitely variable .......................................0-820 fpm (0-250 m/min)Discharge direction: right or leftConveyor belt width..........................1’ 6” (76 cm)Conveyor length..............................8’ 4” (255 cm)Discharge height...............................3’ (91.44 cm) at max digging depth......................6’ 6” (198 cm)

Crawler DriveHydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverse Speed range.................... 0-2.1 mph (0-3.3 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

Standard FeaturesPressurized cab with air conditioning,heating, sound suppression and ROPS structureTrenchTronic 3.0 electronic machine controlwith: • Operator selectable digging pressure and

automatic operation• Fully automatic operation• Remote diagnostic systemElectrical system: 24 VSelf-leveling (tilting) undercarriage:• Track tilt angle: 10°• Automatic/manual operation

EngineModel........................................CAT C6.6 TA Tier 3Max horsepower.........................225 hp (168 kW)Max no load rpm...................................2.200 rpmFuel tank capacity.....................121.5 gal (460 l)Fuel consumption.................12.2 gal/hr (46 l/hr)at full load Cooling rating adequate for 130° F (54.4° C) ambient air temperatureAir cleaner: dry type 2 stages with pre-cleaner and automatic dust ejection

TracksOverall track length....................11’ 1.9” (340 cm)Track pad type: single grouser, chamfered edgesTrack chain type: FL6Track pad width.................................2’ 7” (80 cm)

Available DevicesWork light package: 24 V, for night useAutomatic laser control system for depth control (Trimble make)

0500

975 CS

powered by

Ed. 2013/11




MID-SIZE CHAINSAW TRENCHER CONCEIVED FOR ROCK EXCAVATION FOR UTILITIES PROJECTS SUCH AS FIBER OPTIC, ELECTRIC CABLES, WATER CONDUITS, PIPELINES AND OTHER. THE 975 CAN BE EQUIPPED WITH ELEVATING CABIN AND TILTING TRACKS; UPON REQUEST IT CAN ALSO FIT AN AUTOMATIC LAYING SYSTEM FOR FIBER OPTIC BACK-BONE PROJECTS OR ELECTRIC CABLE NETWORKS. TRENCHTRONIC 3.0 EQUIPPED.

0500

OIL LEVEL

OIL DRAINMOD.41T-140-SAE

WARNING : FAILURE DUETO LACK OF LUBRICATIONVOIDS WARRANTY

GEAR BOX

FILL WITH : 85W/140W

SERIAL N°

OIL LEVEL

OIL DRAIN

OIL DRAIN

OIL LEVEL

OIL LEVEL

OIL DRAIN

OIL LEVEL

"A"

9'-9"[298cm]

8'-2"[249cm]

"B"

1'-

6"

[4

6cm

]

12'-9"[389cm]

11'-10"[360cm]

15

'-1

" [

46

0cm

]

10

°

6'-

0"

[1

84

cm]

2'-0" [61cm] Track

8'-4" [254cm]

Min 12" [30cm]Max 36" [91cm]

5'-0"[153cm]

6'-

0"

[1

84

cm]

5'-0"[153cm]

10

'-4

" [

31

5cm

]

9'-

7"

[2

91

cm]

12

'-7

"[3

85

cm]

6'-

10

" [

20

8cm

]

975

Trencher

TESMEC

Trencher

TESMEC

Tre

nch

er

TESM

EC

-8°

8°

16

°

8' ft MACHINE SHOWN

Keep you updated on: www.tesmec.com




975 ChainsawSpecification

Boom “A” “B”

4’ 4’ (122 cm) 27’-6’’ (839 cm)

6’ 6’ (183 cm) 29’-10’’ (909 cm)

8’ 8’ (244 cm) 32’-6’’ (990 cm)

10’ 10’ (305 cm) 34’-9’’ (1.059 cm)

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum..............43 gpm (164 l/min)Pressure setting......................2.500 psi (172 bar)Oil tank capacity................................73 gal (275 l)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)TrenchTronic 3.0 electronic machine control with: • Operator selectable digging pressure and

automatic operation• Fully automatic operation• Remote diagnostic systemElectrical system: 24 VAnti vibration isolator mounts: used on engine, radiator/oil cooler unit and cabStabilizers with trench cleaners: automatically adjust to terrain changesPositive locking digging chain adjustment

EngineModel....................................CAT C9 ACERT Tier 3Max horsepower.........................325 hp (242 kW)Max no load rpm...................................2.000 rpmFuel tank capacity........................193 gal (730 l)Fuel consumption..............15.4 gal/hr (58.3 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, 2 stages with pre-cleaner and automatic dust ejection

Operating and Transport WeightWeight.......................................55,116-72,752 lbs ..................................(25.000-33.000 kg)Ground pressure.....................9.7-12.4 lbs/Sq Inch ......................(0.68-0.90 kg/cm2)Note: dependent on confi guration and options

Cross ConveyorPressure and flow compensated pump with dual hydraulic drive motorsReversible and shiftableBelt speed infinitely variable .......................................0-790 fpm (0-240 m/min)Discharge direction: right or leftConveyor belt width........................1’ 11” (60 cm)Conveyor length..............................8’ 3” (250 cm)Discharge height..............................4’ 9” (145 cm)

Trencher DriveHydrostatic: one pump and two motors capable of transmitting full engine horsepowerFlywheel gearboxesInfinitely variable digging chain speeds.......................................0-525 fpm (0-160 m/min)Tesmec designed single strand or double link 4.5” (11.4 cm) pitch chain, “K” styleStandard cutters: rotary carbide tipped 1 ½” (3.8 cm) shank diameterOptional cutters: single edge, hard surfaced spade teeth for dirt - Tesmec dirt tool with 1 ½” (3.8 cm) shank diameter

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range.......................0-2.5 mph (0-4 km/hr)• Low range....................0-1.4 mph (0-2.2 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length..........................9’ 9” (298 cm)Track pad type: triple grouserTrack chain type: Caterpillar D5Track pad width......................................2’ (61 cm)

Transport DimensionsLength with crumbshoe without truck loadingconveyor......................4 ft boom: 27’ 6’’ (839 cm) ...................6 ft boom: 29’-10’’ (909 cm) .....................8 ft boom: 32’-6’’ (990 cm) ...............10 ft boom: 34’ 9” (1.059 cm)Width, no motor removal.............8’ 7” (261 cm)Width, with motor removal..........8’ 4” (254 cm)Height ........................................10’ 4” (315 cm)

Trenching DimensionsSINGLE BOOM • Max depth......................................10’ (305 cm)• Widths range.......................12”-18” (30-45 cm)DOUBLE LINK BOOM • Max depth......................................10’ (305 cm)• Widths range.......................18”-28” (45-71 cm)DOUBLE BOOM • Max depth........................................8’ (244 cm)• Widths range.......................24”-36” (61-91 cm)Note: dependent on confi guration and options Available Devices

Work light package: 24 V, for night useLaser control system pre-wireHydraulic crumbshoe Cab anti-vandalism window coversPolyurethane or rubber track padsTESMEC combination digging tool holders

Available on special orderTilt tracks: • Track tilt angle: 9º each direction (18º total)• Automatic/Manual operation

0600

1075 BW

Ed. 2013/11




THE 1075 BW MODEL HAS BEEN DESIGNED AS A HIGH-PRODUCTIVITY TRENCHER FOR PIPELINES AND UTILITIES PROJECTS IN DIRT AND LIGHT ROCKY SOILS. ITS BUCKETS CAN BE EQUIPPED WITH CONICAL OR SPADE TOOLS TO ENSURE THE MAXIMUM PRODUCTIVITY ACCORDING TO THE RELEVANT GROUND CONDITIONS.

0600

13

'-2

" [

40

0cm

]

10

'-9

" [

32

7cm

]

1'-

7"

[4

9cm

]

7'-

0"

[21

3cm

]

10'-9" [328cm]

9'-4" [284cm]

17

'-3

"[5

25

cm]

15

0

36'-10" [1123cm]

37'-8"[1148cm]

RECOILADJUSTER

TRACK

Trencher

TESMEC

Trencher

TESMEC

Trencher

1075


Min 20" [51cm]Max 40" [102cm]

4'-2" [127cm]

2'-8" Track [81cm]

10'-2"[310cm]





1075 Bucket WheelSpecification

EngineModel....................................CAT C9 ACERT Tier 3Max horsepower.........................325 hp (242 kW)Max no load rpm...................................2.200 rpmFuel tank capacity........................216 gal (818 l)Fuel consumption.................16.9 gal/hr (64 l/hr)at full load Cooling rating adequate for 125° F (51.7° C) ambient air temperatureAir cleaner: dry type, centrifugal precleaner with primary and secondary fi lters

Trenching DimensionsDigging depth, dirt..............standard 7 ft (213 cm)Digging depth, dirt................optional 8 ft (244 cmwith the Tesmec “Extended-Depth Buckets” Digging depth, rock............................7 ft (213 cm)Widths of cut: 7 ft-Dirt.........20” Min. (11” Bucket)to max. 40” (28” bucket) (51-102 cm) Widths of cut: 8ft-Dirt..........20” Min. (11” Bucket) to Max. 24” (16” Bucket) (51-61 cm) Widths of cut: 7ft-Rock........20” Min. (11” Bucket) to 26” (16” Bucket) (51-66 cm)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Load control: operator selectable digging pressure, automatic operationStabilizers with adjustable berm scrapers onChainsaw modelElectrical system: 12 V /24 V

Trencher DriveHydrostatic: two pumps and two motors capableof transmitting full engine horsepowerDigging wheel speed.............................0-11.5 rpm

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverse• High range....................0-2.5 mph (0-4.0 km/hr)• Low range....................0-1.3 mph (0-2.1 km/hr)Integral parking brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length................................10’ 9” (328 cm)Track pad type: single, double, or triple grouserTrack chain type: Caterpillar D5Track pad width..........................................2’ 8” (81 cm)

ConveyorPressure and flow compensated pump with dual hydraulic drive motorsReversible and shiftableBelt speed infinitely variable................................0-1.000 fpm (0-304.8 m/min)Discharge direction: right or leftConveyor belt width.....................2’ 12” (91.4 cm)Conveyor length.................................13’ (396 cm)Discharge height..............................3’ 5” (104 cm)

Operating and Transport WeightWeight “Dirt”.............................83,000-92,000 lbs ............................(37.467-41.730 kg)Weight “Rock”............................87,000-92,000 lbs ...........................(39.462-41.730 kg)Note: dependent on confi guration and options

Transport DimensionsLength.........................................37’ 0” (1.127 cm)Width without digging motors.......9’ 9” (296 cm)Width with digging motors...........10’ 2” (310 cm) Height with cab..........................10’ 9” (327 cm)Height with cab elevated............13’ 2” (400 cm)Height with crumbshoe.................10’ 6” (320 cm) (over Cab with single grouser pads) (3-bottom buckets and 2-top buckets removed on “dirt set-up” & 3 and 3 on “rock set-up”)Height with roll-up crumbshoe....11’ 5” (348 cm(over cylinder with single grouser pads) withrespective (dirt/rock) buckets removed

Available DevicesSight rod kit (2 types)Sloper kit (for use with customer supplied cable and ends)Hydraulic winch for conveyor fold

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum..........45 gpm (170 l/min)Pressure setting................... 2.500 psi (172 bar)Oil tank capacity.................108 gallons (408.7 l)

0700

1085 CS

Ed. 2013/11




THE LARGEST OFF-SET CHAIN TRENCHER FOR ROCK EXCAVATION, THIS MODEL CAN BE EQUIPPED WITH A DIGGING CHAIN UP TO 28” (71 CM) WIDE. THE 1085 IS A MID-SIZE UNIT EMPLOYED IN ELECTRIC CABLE AND GAS PIPELINE PROJECTS, IT CAN BE USED ALSO FOR OTHER UTILITIES PROJECTS SUCH AS WATER AND SLURRY PIPELINES.

0700

TRACK

ADJUSTERRECOIL

9°

"A"

"B"

10

'-1

1"

[3

33

cm]

13

'-4

" [

40

6cm

]

Min 18" [45 cm]Max 28" [71 cm]

10'-5" [318cm]

10'-9"[328cm] 2

'-0

" [

61

cm]

9'-2"[279cm]

1'-10" Track

[56cm]

18

°

8'-3" Track

[250cm]

9°

2'-6" [76cm]

8' ft MACHINE SHOWN

Trencher

TESMEC

Trencher

TESMEC

Tre

nch

er

TESM

EC






EngineModel....................................CAT C9 ACERT Tier 3Max horsepower.........................325 hp (242 kW)Max no load rpm...................................2.100 rpmFuel tank capacity........................236 gal (893 l)Fuel consumption..............16.5 gal/hr (62.4 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, centrifugal precleaner with primary and secondary fi lters

Trenching DimensionsDepths.......................4, 6, 8 ft (122, 183, 244 cm)Widths........18”-28” double link chain (45-71 cm) Note: dependent on confi guration and options

Hydraulic TransmissionPressure and flow compensated (Load sensing)Pump flow maximum...............45 gpm (170 l/min)Pressure setting.......................2.500 psi (172 bar)Oil tank capacity........................108 gal (408.7 l)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Load control: operator selectable digging pressure, automatic operationTool box/battery box with locking doorEngine doors with security locksFlywheel gearboxes and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersFlywheel gearboxes: shaved, helical gearing, case hardened for extreme shock loadVibration isolator mount: used on engine, radiator, oil cooler, and exhaust silencerElectrical system..................................12 V / 24 V

Trencher DriveHydrostatic: two pumps and two motors capableof transmitting full engine horsepowerInfinitely variable digging chain speeds.......................................0-700 fpm (0-213 m/min) Cutters: rotary carbide tipped 1” (2.5 cm) shank diameterOPTIONAL cutters: rotary carbide tipped 1 ½” (3.81 cm) shank diameter Double link chain tensile strength......................................509,130 lbs (230.940 kg)Tailwheel diameter........................3’ 4” (101.6 cm)Double link chain tensile strength......................................509,130 lbs (230.940 kg)

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverse• High range...................0-3.1 mph (0-4.9 km/hr)• Low range....................0-1.3 mph (0-2.1 km/hr)Integral parking and emergency brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length................................10’ 9” (328 cm)Track pad type: single, double, or triple grouserTrack chain type: Caterpillar D5Track pad width........................................1’ 10” (56 cm)

ConveyorPressure and flow compensated pump with dual hydraulic drive motorsDescription: reversible and shiftable 12” (30.5 cm) in each directionBelt speed infinitely variable.......................................0-750 fpm (0-229 m/min)Discharge direction: right or leftConveyor belt width............................2’ (60.9 cm)Conveyor length..............................8’ 3” (250 cm)

Operating and Transport WeightWeight.......................................85,000-95,000 lbs ....................................(38.556-43.092 kg)Note: dependent on confi guration and options

Available DevicesWork light package: 24 V, for night useLaser control system pre-wireCab anti-vandalism window coversAir compressor

Transport DimensionsLength with crumbshoe.................................4 ft boom: 36’ 9” (1.120 cm).................................6 ft boom: 39’ 2” (1.190 cm).................................8 ft boom: 41’ 5” (1.260 cm)Width...........................................8’ 3” (250 cm) with 22” (0.56 m) track padsHeight with cab .......................10’ 11” (333 cm)Height with cab elevated............13’ 4” (406 cm)Attachment Offset..........................2’ 6” (76.2 cm) from machine centerline either direction (60” (152.4 cm) total), hydraulically shiftable the entire distance without cylinder change


4’ 4’ (122 cm) 36’-9’’ (1120 cm)

6’ 6’ (183 cm) 39’-2’’ (1190 cm)

8’ 8’ (244 cm) 41’-5’’ (1260 cm)

0900

1150XHD CS

powered by

Ed. 2013/11




50 METRIC TON-CLASS, TRENCHTRONIC 3.0 EQUIPPED ROCK TRENCHER FOR MID-SIZE PIPELINES; THE 1150XHD IS THE BEST-SELLING TESMEC TRENCHER. THIS MODEL IS EQUIPPED WITH A 440 HP ENGINE AND CAN DIG UP TO 12’ (366 CM) DEEP AND UP TO 42” (107 CM) WIDE, MAKING IT THE IDEAL TRENCHER FOR MID-SIZE PIPELINES AND UNDERGROUND UTILITIES.

0900

6' ft MACHINE SHOWN

13

'-1

" [

39

9cm

]

8'-11" Track [271cm]

11

'-1

"[3

38

cm]

2'-0" Track [60cm]

"A"

"B"

12'-5" [379cm]

10'-7" [322cm]

9'-6"[290cm]

14

°

12'-5" [378cm]

4'-9" [145cm]

Min 18" [45cm]Max 42" [107cm]

10'-6"[320cm]

15

'-0

"[4

57

cm]

1'-

11

"[5

7cm

]

Trencher

TESMEC

Trencher

TESMEC

1150

Tre

nch

er

TESM

EC

Tre

nch

er

TESM

EC





1150XHD ChainsawSpecification

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum...........63.4 gpm (240 l/min)Pressure setting......................2.500 psi (172 bar)Oil tank capacity...........................100 gal (378.5 l)


automatic operation• Fully automatic operation• Remote diagnostic systemElectrical system: 24 VStabilizers with adjustable dragsGearboxes, fuel and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersVibration isolator mounts: used on engine, radiator, oil cooler, exhaust silencer and cab

EngineModel..................................CAT C13 ACERT Tier 3Max horsepower.........................440 hp (328 kW)Max no load rpm.....................................2.150 rpmFuel tank capacity....................324 gal (1.230 l)Fuel consumption....................23 gal/hr (87 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, 2 stages with pre-cleaner and automatic dust ejection

Operating and Transport WeightWeight...................................110,231-132,278 lbs ......................................(50.000-60.000 kg)Ground pressure...................15.6-18.5 lbs/Sq Inch ...........................(1.1-1.3 kg/cm2)Note: dependent on confi guration and options

Cross ConveyorPressure and flow compensated pump with dual hydraulic drive motorsReversible and shiftableBelt speed infinitely variable .......................................0-750 fpm (0-229 m/min)Discharge direction: right or leftConveyor belt width..........................2’ 6” (76 cm)Conveyor length............................13’ 8” (416 cm)Discharge height............4’-4”- 5’-11” (123-181 cm)

Trencher DriveHydrostatic: two pumps and two motors capable of transmitting full engine horsepowerFlywheel gearboxes: shaved, helical gearing, case hardened for extreme shock loadInfinitely variable digging chain speeds......................................0 -550 fpm (0-168 m/min)Tesmec designed 6.5” pitch digging chain for single chain configuration or 4.5’’ pitch digging chain for double chain configurationCutters: rotary carbide tipped 1 ½” (3.81 cm) shank diameter

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range................0-2.77 mph (0-4.46 km/hr)• Low range................0-1.25 mph (0-2.01 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length.......................12’ 5” (379 cm)Track pad type: triple grouserTrack chain type: Caterpillar 42/325 or equivalentTrack pad width.....................................2” (60 cm)

Transport DimensionsLength with crumbshoe with crumbshoe andcounterweight.........6 ft boom: 36’ 5” (1.112 cm) .........8 ft boom: 38’ 5” (1.172 cm) .......10 ft boom: 40’ 9” (1.242 cm) .......12 ft boom: 42’ 9” (1.304 cm)Width*.........................................9’ 6” (290 cm)Height with cabin.......................11’ 1” (338 cm)* width could be reduced to 110” (280 cm) removing digging motors

Trenching DimensionsSINGLE CHAIN BOOM • Max depth........................................8’ (244 cm)• Widths range......................18”-20” (45-51 cm)DOUBLE CHAIN NARROW BOOM • Max depth......................................12’ (366 cm)• Widths range.......................28”-36” (71-91 cm)DOUBLE CHAIN WIDE BOOM• Max depth......................................10’ (305 cm)• Widths range.....................34”-42” (86-107 cm)Note: dependent on confi guration and options Available Devices

Work light package: 24 V, for night useLaser control systemHydraulic crumbshoe Cab anti-vandalism window coversTESMEC combination digging tool holders


6’ 6’ (183 cm) 36’-5’’ (1112 cm)

8’ 8’ (244 cm) 38’-5’’ (1172 cm)

10’ 10’ (305 cm) 40’-9’’ (1242 cm)

12’ 12’ (366 cm) 42’-9’’ (1304 cm)

1100

1175XHD BW

Ed. 2013/11




60 METRIC TON-CLASS BUCKET WHEEL TRENCHER FOR MID TO BIG SIZE PIPELINES AND UTILITIES EXCAVATION IN “DIRT” AND LIGHT ROCKY SOILS; THE 1175XHD MODEL IS AS A HIGH-PRODUCTIVITY MACHINE THAT CAN BE EQUIPPED WITH CONICAL OR SPADE TOOLS TO ENSURE THE MAXIMUM PRODUCTIVITY ACCORDING TO THE DIFFERENT GROUND CONDITIONS.

1100

FLO

AT

FLO

AT

RECOILTRACK

ADJUSTER

12'-2"[371cm]

14

'-1

" [

42

9cm

]

44'-5" [1354cm]

43'-3" [1318cm]

1'-

9"

[5

3cm

]

10'-4" Tracks [315cm]

9'-

0"

[2

74

cm]

11'-3"[343cm]

7'-11" [241cm]

2'-6" Track [76cm]

11'-3" [343cm]

18'-10" [573cm]

Min 30" [76cm]Max 54" [137cm]

4'-

11

" [

15

0cm

]

11

'-6

" [

35

1cm

]

13

'-1

1"

[4

24

cm]

14

°

Trencher

TESMEC

Trencher

TESMEC

Trencher

TESMEC





1175XHD Bucket WheelSpecification

Operating and Transport WeightWeight “Dirt”...........135,000-142,000 lbs (61.235- 64.410 kg) Weight “Rock”.........................................142,000 lbs (64.410 kg)Note: dependent on confi guration and options

Transport DimensionsLength........................................44’ 5” (1.354 cm)Width.........................................10’ 4” (315 cm) with digging motors removed, 30” (76 cm) D7 track padsHeight........................................... 14’ 1” (429 cm) over wheel with (3) buckets removed from bottom and (2) from the top

Trenching DimensionsDepths............................3 ft min (91 cm with boom level) ...................................................max 9 ft (274 cm)Widths of cut, Dirt.....30” (76 cm) to 54” (137 cm) Widths of cut, Rock.............................30” (76 cm)Note: dependent on confi guration and options

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum..............45 gpm (170 l/min)Pressure setting......................2.500 psi (172 bar)Oil tank capacity..............................177 gal (670 l)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)External support structure for elevating cab, wear-pad design with adjustmentLoad control: operator selectable digging pressure, automatic operationBattery box and toolbox with locking doorEngine doors with security locksFuel and hydraulic tank: aircraft quality locking capsFlywheel gearboxes and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersVibration isolator mount: used on engine, radiator, oil cooler, and exhaust silencerStabilizers / dirt drags: automatically adjust to terrain changes.Lights: 24 V forward facingElectrical system: 12 /24 V

EngineModel..................................CAT C13 ACERT Tier 3Max horsepower.........................440 hp (328 kW)Max no load rpm...................................2.100 rpmFuel tank capacity....................295 gal (1.124 l)Fuel consumption.................22.7 gal/hr (86 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, centrifugal precleanerwith primary and secondary fi lters

Trencher DriveHydrostatic: four pumps and two motors capable of transmitting full engine horsepowerThree operator selectable wheel speeds:0-6.8 rpm, 0-10.3 rpm, 0-13.7 rpmCenter pull articulated wheelHeavy-duty trapezoid design boomHeavy-duty hydraulic lift and tilt cylindersFixed crumbshoeHardened alloy steel shaft with multiple flanges for easy “digging-width” changesHardened reversible split drive sprockets Four truck assemblies, two upper and two lower with standard 14” (35.6 cm) ride diameter wheels

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range..................0-3.0 mph (0-4.83 km/hr)• Low range..................0-1.6 mph (0-2.57 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length......................12’ 2” (371 cm)Track pad type: single, double or triple grouserTrack chain type: Caterpillar D7Track pad width..............................2’ 6” (76.2 cm)Optional track pad width........................2’ (61 cm)

Available DevicesWork light package: 24 V, for night useLaser control system pre-wireHydraulic crumbshoeCab anti-vandalism window coversAir compressorTwin hose reel package: connections to power hydraulic tools

Cross ConveyorPressure and flow compensated pump with dual hydraulic drive motorsReversible and shiftableBelt speed infinitely variable .......................................0-750 fpm (0-229 m/min)Discharge direction: right or leftConveyor belt width........................3’ 5” (107 cm)Discharge height: variableManual conveyor fold

1300

1375 BW

Ed. 2013/11




70 METRIC TON-CLASS BUCKET WHEEL TRENCHER CONCEIVED AS A HIGH-PRODUCTIVITY MACHINE FOR BIG DIAMETER PIPELINES AND UTILITIES PROJECTS IN DIRT AND LIGHT ROCKY SOILS, THIS MODEL CAN DIG UP TO 9’6” (291 CM) DEEP AND 66” (168 CM) WIDE. ITS BUCKETS CAN BE EQUIPPED WITH CONICAL OR SPADE TOOLS TO ENSURE THE MAXIMUM PRODUCTIVITY ACCORDING TO THE DIFFERENT GROUND CONDITIONS.

1300

11

'-5

" [

34

8cm

]

9'-

6"

[29

1cm

]

13

'-8

" (W

/Ext

en

de

d T

rack

) [

41

7cm

]

14'-0" Tracks(Extended) [427cm]

Min 36" [91cm]Max 66" [168cm]

6'-5" [195cm]

45'-3" [1379cm]

46'-6" [1417cm]

12'-3" [372cm]

13'-0" [397cm]

1'-

10

" [

56

cm]

12

0


20

'-1

1"

[63

6cm

]

14

'-9

"[4

50

cm]

ISO 6682

TRACKRECOIL

ADJUSTER

Trencher

TESMEC

Trencher

TESMEC






Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum...................45 gpm (170 l/min)Pressure setting...........................2.500 psi (172 bar)Oil tank capacity..................................203 gal (768 l)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Load control: operator selectable digging pressure, automatic operationToolbox with locking doorsEngine doors with security locksFuel and hydraulic tank: aircraft quality locking capsGearboxes and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersFlywheel gearboxes: shaved, helical gearing, case hardened for extreme shock loadVibration isolator mounts: used on engine, radiator, oil cooler External support structure for elevating cab, wear-pad design with adjustmentCenter pull articulated wheelRadial arm articulationHeavy-duty trapezoid design boomHeavy-duty hydraulic lift and tilt cylindersFixed crumbshoeExtendable undercarriageElectrical system: 24 V starting, 12 V controls

EngineModel.......................................CAT C15 ACERT Tier 3Max horsepower..............................540 hp (403 kW)Max no load rpm........................................2.100 rpmFuel tank capacity........................376 gal (1.423 l)Fuel consumption................28.9 gal/hr (109.4 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, centrifugal pre-cleanerwith primary and secondary fi lters

Operating and Transport WeightWeight......160,000-175,000 lbs (72.575–79.379 kg) Note: dependent on confi guration and options

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range......................0-2.06 mph (0-3.3 km/hr)• Low range....................0-1.17 mph (0-1.87 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length............................12’ 3” (372 cm)Track pad type: single grouserTrack chain type: Caterpillar D7Track pad width...................................2’ 10” (86 cm)

Trenching DimensionsDepths minimum 3 ft (91 cm) with boom level........................................maximum 9’ 6” (291 cm)Widths of cut.....from 36” (91 cm) to 66” (168 cm)Note: dependent on confi guration and options

Trencher DriveHydrostatic: four pumps and two motorsThree operator selectable digging speed ranges:...............................0-7 rpm (351 ft/min) (107 m/min).............................0-10 rpm (500 ft/min) (152 m/min).............................0-12 rpm (600 ft/min) (183 m/min)Digging rims: 1 ½” Plate (3.81 cm) with forged steel segments multiple drilled for (15) or (18) bucket set-upAvailable cutters: rotary carbide tipped 1 ½ diameter (3.81 cm) shank, H&L dirt teeth and pockets, TESMEC combo pockets for dirt & conical tools, ESCO type teeth and adaptors

Transport DimensionsLength............................................45’ 3” (1.379 cm)Width...............................................144” (366 cm) with digging motors removed, 2’ 10” (86 cm) D7 track padsHeight.............................................14’ 4” (437 cm)(over wheel with lower and upper buckets removed, and single grouser pads)Width with extended tracks...................14’ (427 cm) Height.................................................13’ 8” (417 cm) over wheel with (3) buckets removed from bottomand (2) from the top

Available DevicesWork light package: 24 V, for night useLaser control systemCab anti-vandalism window coversTwin hose reel package: connections to power hydraulic toolsStraight conveyor with winch fold

Cross ConveyorHydrostatic: one pump and two motors Reversible and shiftableBelt speed infinitely variable.......................................0-1.000 fpm (0-305 m/min)Discharge direction: right or leftConveyor belt width.................................4’ (122 cm) Discharge height: variableManual conveyor fold

Headshaft AssemblyHardened alloy steel shaft with multiple flanges for easy “digging-width” changesHardened reversible split drive sprockets

Wheel Truck AssembliesFour assemblies, two upper and two lower with standard 14” (35.6 cm) ride diameter wheels Factory set heavy-duty tapered roller bearings

Heavy-duty mechanical seals with replaceable elements

1400

1475 CS

powered by

Ed. 2013/11




90 METRIC TON-CLASS ROCK TRENCHER FOR MID TO BIG SIZE PIPELINES, THE 1475 IS THE SECOND LARGEST TESMEC CHAINSAW TRENCHER. TRENCHTRONIC 3.0 EQUIPPED, THIS 630 HP POWERED UNIT CAN DIG TRENCHES FOR BIG-DIAMETER PIPE UP TO 16’ (488 CM) DEEP IN THE TOUGHEST CONDITIONS.

1400

Trencher

Trencher

14

0

Trencher

10'-4" [315cm]

2'-

2"

[6

5cm

]

12

'-3

" [

37

3cm

]

14

'-6

" [

44

1cm

]

15'-6" [473cm]

Tre

nch

er

"B"

35'-3" Tractor W/Stabilizers [1073cm]

"A"

7'-

7"

[2

31

cm]

17'-3"[525cm]

Min 32" [81cm]Max 48" [122cm]

11'-6" Tracks [350cm]

2'-6" Track[76cm]

4'-11"[151cm]






Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum...................45 gpm (170 l/min)Pressure setting..........................2.500 psi (172 bar)Oil tank capacity..................................191 gal (723 l)


automatic operation• Fully automatic operation• Remote diagnostic systemBattery box and toolbox with locking doorFuel and hydraulic tank: aircraft quality locking capsFlywheel gearbox and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersFlywheel gearbox: shaved, helical gearing, case hardened for extreme shock loadVibration isolator mount: used on engine, radiator, oil cooler, and exhaust silencerStabilizers / dirt drags (chainsaw only): automatically adjust to terrain changesLights: 24 V forward facing Hydraulic cooler externally mountedElectrical system: 24 V

EngineModel.......................................CAT C18 ACERT Tier 3Max horsepower..............................630 hp (470 kW)Max no load rpm.........................................2.150 rpmFuel tank capacity........................360 gal (1.363 l)Fuel consumption...................34.6 gal/hr (131 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, centrifugal pre-cleanerwith primary and secondary fi lters

Operating and Transport WeightWeight........................................169,756-242,509 lbs ......................................(77.000-110.000 kg)Ground pressure..........................15-21.5 lbs/Sq Inch ...........................(1.05-1.51 kg/cm2)Note: dependent on confi guration and options

Cross ConveyorHydrostatic: one pump and two motorsReversible and shiftableBelt speed infinitely variable............................................0-900 fpm (0-275 m/min)Discharge direction: right or leftConveyor belt width..........................2’ 11” (91.4 cm) Conveyor length.................................14’ 9” (450 cm) Discharge height..................................7’ 7” (231 cm)

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range....................0-1.62 mph (0-2.59 km/hr)• Low range....................0-0.81 mph (0-1.30 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length............................15’ 6” (473 cm)Track pad type: triple grouserTrack chain type: Caterpillar D8K (1” bolts)Track pad width.....................................2’ 6” (76 cm)

Trenching DimensionsSECTIONABLE BOOM• Depths range....................................8’ through 16’ ..................(244 cm through 488 cm)• Min width.........................................32” (81 cm)• Max width limited by depth:

• Max width 48” (122 cm) at 12’ (366 cm) depth• Max width 42” (107 cm) at 14’ (427 cm) depth• Max width 36” (91 cm) at 16’ (488 cm) depth

Note: dependent on confi guration and options

Trencher DriveHydrostatic: four pumps and two motors capable of transmitting full engine horsepowerFlywheel gearboxes, shaved, helical gearing, case hardened for extreme shock load4 operator selectable digging speed ranges:............................................0-400 fpm (0-122 m/min)............................................0-470 fpm (0-143 m/min)............................................0-530 fpm (0-162 m/min)............................................0-600 fpm (0-183 m/min)Tailwheel diameter....................................4’ (122 cm)Headshaft diameter..................................1’ (30.8 cm)Cutters: rotary carbide tipped 1 ½” (3.81 cm) shank diameterDigging chain: D9L

Transport DimensionsLength with crumbshoe.....................................8 ft boom: 42’ 7” (1.292 cm)........................................10 ft boom: 45’ (1.372 cm)...................................12 ft boom: 47’ 7” (1.452 cm)........................................14 ft boom: 51’ (1.553 cm)...................................16 ft boom: 52’ 5” (1.592 cm)Length without boom:only tractor with stabilizers...........35’ 3” (1.073 cm)Width.............................................11’ 6” (350 cm) with motor removalHeight with cab..............................12’ 3” (373 cm)Height with cab elevated .......... ....14’ 6” (441 cm)

Available DevicesWork light package: 24 V, for night useLaser control systemHydraulic crumbshoeCab anti-vandalism window coversAir compressor


8’ 8’ (244 cm) 42’-7’’ (1292 cm)

10’ 10’ (305 cm) 45’ (1372 cm)

12’ 12’ (366 cm) 47’-7” (1452 cm)

14’ 14’ (427 cm) 51’ (1553 cm)

16’ 16’ (488 cm) 52’-5’’ (1592 cm)

1600

1575 BW

Ed. 2013/11




TESMEC’S LARGEST BUCKET WHEEL IS CONCEIVED AS A HIGH-PRODUCTIVITY MACHINE FOR BIG DIAMETER PIPELINES AND UTILITIES PROJECTS IN “DIRT” AND LIGHT ROCKY SOILS. ITS BUCKETS CAN BE EQUIPPED WITH CONICAL OR SPADE TOOLS TO ENSURE THE MAXIMUM PRODUCTIVITY ACCORDING TO THE DIFFERENT GROUND CONDITIONS. NO OTHER TRENCHER MACHINE CAN GRANT SUCH PRODUCTIVITY IN TERMS OF LINEAR METERS PER HOUR (FOOT PER MINUTE).

1600

TOO-6500-265

CAT #166-4929

CAT 350

CAT #166-4929

CAT 350

36

LC

ADJUSTERRECOIL

TRACK

CAT #166-4929

CAT 350

CAT #166-4929

CAT 350

36

boom 1017

2'-

5"

[7

3cm

]

Max 6'-0" [183cm]

14'-0" Tracks [427cm]

12

'-1

" [

36

7cm

]

14

'-6

" [

44

3cm

]

3'-0" Track [91cm]

8'-

0"

[24

4cm

]

15'-8"[478cm]

11'-9"[358cm]

51'-11"[1582cm]

14

°

7'-0" [213cm]

2'-

2"

[6

6cm

]

Trencher

TESMEC

Trencher

TESMEC







Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Load control: operator selectable digging pressure, automatic operationBattery box and toolbox with locking doorEngine doors with security locksGearboxes and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersFlywheel gearboxes: shaved, helical gearing, case hardened for extreme shock loadVibration isolator mount: used on engine, radiator, oil cooler, exhaust silencer, and cab Center pull articulated wheelRadial arm articulation with quick disconnect mastHeavy-duty design boomHeavy-duty hydraulic lift and tilt cylindersExtending undercarriageFixed crumbshoe Electrical system: 24 V starting, 12 V controls

EngineModel.......................................CAT C18 ACERT Tier 3Max horsepower..............................630 hp (470 kW)Max no load rpm........................................2.100 rpmFuel tank capacity........................500 gal (1.893 l)Fuel consumption...................34.6 gal/hr (131 l/hr)at full load Cooling rating adequate for 130° F (54.4° C) ambient air temperatureAir cleaner: dry type, centrifugal pre-cleanerwith primary and secondary fi lters

Operating and Transport WeightWeight.....210,000-248,000 lbs (95.255-112.491 kg)Note: dependent on confi guration and options


TracksOverall track length............................15’ 8” (478 cm)Track pad type: single, double or triple grouserTrack chain type: Caterpillar 62/350Track pad width...........................................3’ (91cm)

Trenching DimensionsDepths 3’ 8” through 10’ (112 cm through 304 cm)Width 34” (86 cm) buckets 42”-52” (107-132 cmCut 15 or 18 bucketsWidth 46” (117 cm) buckets 54”-66” (137-168 cmCut 15 or 18 bucketsWidth 64” (163 cm) Buckets 72” (183 cm)Cut 15 or 18 bucketsNote: dependent on confi guration and options

Trencher DriveHydrostatic: four pumps and two motors capable of transmitting full engine horsepowerThree operator selectable digging speed ranges:.........................1st: 0-345 fpm (0-105 m/min) (6 rpm)........................2nd: 0-518 fpm (0-158 m/min) (9 rpm)......................3rd: 0-633 fpm (0-193 m/min) (11 rpm)Cutters: spade type teeth, rotary carbide tipped 1 ½” (3.8 cm) shank diameter teeth, or ESCO teethDigging rims: double segmented, 2” (5.1 cm) plate main rims with multiple drilled false rims to accept 15, or 18 bucketsBuckets style: semi-round style

Transport DimensionsLength, tractor...................................27’ 8” (8.43 cm) with no front counter weight Length, backend.................................28’ 6” (868 cm) Width.............................................2’ 12” (366 cm) with 36” (91 cm) track pads (w/ motors removed)Height.............................................14’ 4” (437 cm)(over wheel with lower and upper buckets removed, and single grouser pads)Height, tractor with cab.....................12’ 1” (367 cm)Height, tractor with cab elevated......14’ 6” (443 cm)

Available DevicesWork light package: 24 V, for night useLaser control systemCab anti-vandalism window coversStabilizers or adjustable bern-scrapersTwin hose reel package: connections to power hydraulic tools

Cross ConveyorHydrostatic: one pump and two motors w/gear reducerReversible and shiftableBelt speed infinitely variable.......................................0-1.000 fpm (0-305 m/min)Discharge direction: right or leftConveyor belt width.................................4’ (122 cm) Conveyor length.................................20’ 0” (610 cm) Discharge height.......................................6’ (183 cm)Hydraulic winch lift and fold

Headshaft AssemblyHardened alloy steel shaft with multiple flanges for easy rim width changesHardened reversible split drive sprockets

Wheel Truck AssembliesModular spindle type assemblies for two lower trucks, using heavy duty tapered roller bearingsHeavy-duty mechanical seals

2 upper truck assemblies (1) front and (1) rear with 6” (15.2 cm) diameter high alloy steel shafts with extra heavy-duty bearings and self centering spacers

1700

1675 CS

Ed. 2013/11




TESMEC’S LARGEST CHAINSAW TRENCHER IS CONCEIVED AS A HIGH-PRODUCTIVITY MACHINE FOR BIG DIAMETER PIPELINES AND UTILITIES PROJECTS IN HARD ROCK. TRENCHTRONIC 3.0 EQUIPPED, THANKS TO ITS 751 HP ENGINE THE 1675 CAN CUT TRENCHES UP TO 22’ (671 CM) DEEP AND 72” (183 CM) WIDE. THE PEAK OF EXCELLENCE FOR BIG PROJECTS IN THE TOUGHEST EXCAVATING CONDITIONS.

powered by

1700

20' ft MACHINE SHOWN

16

'-5

" [

50

0cm

]

13'-1" Tracks [398cm]

13

'-1

" [

39

9cm

]

2'-6" Track [76cm]

"A"

"B"

2'-

7"

[79

cm]

14'-6" [441cm]

19'-0" [579cm]

5'-7" [171cm]

Min 28" [71 cm]Max 42" [183 cm]

10'-2"[310cm]

18

'-1

1"

[5

77

cm]

13

°9'-4"

[284cm]

15'-11"[484cm]

15'-11"[484cm]

40'-11"[1247cm]

Tren

cher

TESM

EC

1675

Trencher

TESMEC

Trencher

TESMEC







Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Elevating cab module with roll over protection (ROPS)TrenchTronic 3.0 electronic machine control with:• Operator selectable digging pressure and

automatic operation• Fully automatic operation• Remote diagnostic systemBattery box and toolbox with locking doorEngine doors with security locksGearboxes and hydraulic tanks: pressurized with 5 psi (0.3 bar) filtered breathersVibration isolator mount: used on engine, radiator, oil cooler, and exhaust silencerConveyor fold: hydraulic winchLights: 24 V forward facingElectrical system: 24 V

EngineModel..............................................Cummins QSK 19Max horsepower..............................760 hp (567 kW)Max no load rpm.........................................2.100 rpmFuel tank capacity........................430 gal (1.630 l)Fuel consumption......................36 gal/hr (136 l/hr)at full loadCooling rating adequate for 122° F (50° C) ambient air temperature @ 8.000 ft (2.438 m) altAir cleaner: dry type, 2 stages with dualpre-cleaner

Operating and Transport WeightWeight........................................249,124-308,649 lbs ..................................(113.000-140.000 kg)Ground pressure..........................21.8-27 lbs/Sq Inch ...........................(1.53-1.90 kg/cm2)Note: dependent on confi guration and options

Trencher DriveHydrostatic: four pumps and two motors capable of transmitting full engine horsepowerFlywheel gearboxes, shaved, helical gearing, case hardened for extreme shock loadInfinitely variable digging chain speeds:Depths............8’ through 24’ (244 cm through 732 cm)Sectional Boom4 operator selectable digging speed ranges:............................................0-350 fpm (0-107 m/min)............................................0-430 fpm (0-131 m/min)............................................0-500 fpm (0-152 m/min)............................................0-570 fpm (0-174 m/min)Tailwheel diameter....................................4’ (122 cm)Headshaft diameter..................................1’ (31.8 cm)Cutters: rotary carbide tipped 1 ½” (3.8 cm) shank diameterDigging chain: 67/D9N

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range.........................0-2.1 mph (3.36 km/hr)• Low range..........................0-1.1 mph (1.76 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length..........................15’ 11” (484 cm)Track pad type: double or triple grouserTrack chain type: Caterpillar 245BTrack pad width.....................................2’ 6” (76 cm)

Transport DimensionsLength with boom and guard:.......................................10 ft boom: 47’ (1.434 cm)...................................12 ft boom: 49’ 5” (1.505 cm)...................................14 ft boom: 51’ 9” (1.578 cm)...................................16 ft boom: 54’ 2” (1.650 cm)...................................18 ft boom: 56’ 6” (1.721 cm).................................20 ft boom: 58’ 11” (1.795 cm)...................................22 ft boom: 59’ 8” (1.818 cm)...................................24 ft boom: 60’ 4” (1.840 cm)Length without boom:only tractor with stabilizers.........40’ 11” (1.247 cm)Width.............................................13’ 1” (398 cm) with 30” (76 cm) track padsHeight with cab..............................13’ 1” (398 cm)

Cross ConveyorHydrostatic: one pump and two motorReversible and shiftableBelt speed infinitely variable ............................................0-900 fpm (0-275 m/min)Discharge direction: right or leftConveyor belt width.............................3’ 6” (107 cm)Conveyor length.................................17’ 0” (518 cm) or.................................21’ 0” (640 cm)Discharge height..................................8’ 1” (246 cm) or............................... 9’ 10” (300 cm)

Trenching DimensionsDOUBLE CHAIN NARROW BOOM• Max depth..........................................24’ (732 cm)• Widths range..........................28”-48” (71-122 cm)DOUBLE CHAIN WIDE BOOM• Max depth..........................................22’ (671 cm)• Widths range........................40”-60” (102-152 cm)TRIPLE CHAIN WIDE BOOM• Max depth..........................................14’ (427 cm)• Widths range........................54”-72” (137-183 cm)Note: dependent on confi guration and options

Available DevicesWork light package: 24 V, for night useLaser control systemHydraulic crumbshoeCab anti-vandalism window coversAir compressorIncreased cooling capacity for high temperature ambient applicationTruck conveyor


16’ 16’ (488 cm) 57’-3’’ (1745 cm)

18’ 18’ (549 cm) 59’ (1799 cm)

20’ 20’ (610 cm) 60’-10’’ (1855 cm)

22’ 22’ (671 cm) 62’-8’’ (1911 cm)

24’ 24’ (732 cm) 64’-7’’ (1967 cm)


8’ 8’ (244 cm) 57’-7’’ (1541 cm)

10’ 10’ (305 cm) 52’-2’’ (1589 cm)

12’ 12’ (366 cm) 53’-10’’ (1640 cm)

14’ 14’ (427 cm) 55’-6” (1692 cm)

1800

M3 CS

powered by

Ed. 2013/11




TESMEC’S SMALLEST TORQUE CONVERTER EQUIPPED UNIT @ 350 HP FEATURES VERY HIGH CHAIN PULL AND VERY LOW CHAIN SPEED. ORIENTED TOWARD TRENCHING REQUIREMENTS IN HIGHLY ABRASIVE AND EXTREME ROCK CONDITIONS. TRENCHTRONIC 2.0 EQUIPPED.

1800

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TRACK

ADJUSTERRECOIL

TESM

EC

TESM

EC

TESM

EC

TESMEC

TESMEC

TESMEC

TESM

EC

TESM

EC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

Trencher

TESMEC

13

°


Trencher

TESMEC

Tre

nch

er

TESM

EC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESM

EC

TESM

EC

TESM

EC

TESM

EC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMECTESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

TESMEC

14

'-8

" [

44

7cm

]

6'-

1"

[1

86

cm]

5'-0"[153cm]

2'-0" Tracks [61cm]

8'-9" [267cm]

Min 26" [66cm]Max 40" [102cm]

1'-

7"

[4

9cm

]

12'-6"[381cm]"A

"

"B"

11

'-2

" [

34

0cm

]





M3 ChainsawSpecification

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum...................45 gpm (170 l/min)Pressure setting...........................2.750 psi (189 bar)Oil tank capacity.....................................97 gal (367 l)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Load control: automatic optimal digging performance featureAuto stabilizers or adjustable bern scrapers on chainsaw models (optional)Tool box/battery box with locking doorEngine doors with security locksFuel and hydraulic tank: aircraft quality locking capsStabilizers / dirt drags: automatically adjust to terrain changes.Lights: 24 V forward facingDigging chain boom top rollerHydraulic digging chain adjustmentVibration isolator mount: used on engine, radiator and oil coolerConveyor fold: hydraulic winchElectrical system: 24 V starting, 24 V controls

EngineModel.........................................CAT C9 ACERT Tier 3Max horsepower..............................350 hp (261 kW)Max no load rpm........................................2.100 rpmFuel tank capacity........................300 gal (1.136 l)Fuel consumption..................18.6 gal/hr (70.4 l/hr)at full load Cooling rating adequate for 130° F (54.4° C) ambient air temperatureAir cleaner: dry type, centrifugal pre-cleanerwith primary and secondary fi lters

Operating and Transport WeightWeight.........95,000-135,000 lbs(43.091-61.235 kg)Note: dependent on confi guration and options


TracksOverall track length c/c......................12’ 6” (381 cm)Track pad type: single, double or triple grouserTrack chain type: Caterpillar D6Track pad width...........................................2’ (61cm)

Trenching DimensionsDepths 6’ through 12’ (183 cm through 366 cm)Depths:....................26”-40” (66-102 cm) max 6’ (183 cm)....................26”-40” (66-102 cm) max 8’ (244 cm)..................26”-40” (66-102 cm) max 10’ (305 cm)..................26”-40” (66-102 cm) max 12’ (366 cm)Cut widths: double chainNote: dependent on confi guration and options

Trencher DriveThis powertrain is comprised of several components: an electronically controlled transmission driving a heavy-duty differential,which transmits power to the headshaft via sprockets and multi-strand roller chainFive operator selectable digging speed ranges:..................................1st: 115-157 fpm (35-48 m/min).................................2nd: 151-206 fpm (46-63 m/min).................................3rd: 211-288 fpm (64-88 m/min)...............................4th: 288-394 fpm (88-120 m/min).............................5th: 412-562 fpm (126-171 m/min)Cutters: rotary carbide tipped 1 ½” (3.81 cm) shank diameterChain option: 54/345Note: chain speed are “as calculated” per a set-point horsepower output and may vary accordingly

Transport DimensionsLength with crumbshoe:6 ft boom: 38’ 0” (1158 cm)8 ft boom: 40’ 6” (1235 cm)10 ft boom: 42’ 4” (1290 cm)12 ft boom: 44’ 7” (1359 cm)Width..............................................87’ 6’’(267 cm) with 24” (61 cm) track padsHeight with cab................................8’ 9” (340 cm)Height with cab elevated ...............14’ 8” (447 cm)Height..................................................11’ 2” (340 m) over cab with single grouser padsover crumbshoe cylinder...................11’ 8” (360 cm)

Available DevicesWork light package: 24 V, for night useLaser control system pre-wireHydraulic crumbshoeCab anti-vandalism window coversAir compressorStabilizers or adjustable bern-scrapers

Cross ConveyorHydrostatic: one pump and two motorsReversible and shiftableBelt speed infinitely variable.......................................0-1.000 fpm (0-305 m/min)Discharge direction: right or leftConveyor belt width............................2’ 6” (76.2 cm) Conveyor length.................................12’ 4” (376 cm) Discharge height..................................6’ 1” (186 cm)

TransmissionModel: caterpillarOil filter: 6 micron paper cartridge integral filterElectronically controlled utilizing (5)digging speedsCapacity (refill).....................................10 gal (38 l)


6’ 6’ (183 cm) 38’-0’’ (1158 cm)

8’ 8’ (244 cm) 40’-6’’ (1235 cm)

10’ 10’ (305 cm) 42’-4’’ (1290 cm)

12’ 12’ (366 cm) 44’-7’’ (1359 cm)

1900

M5 CS

powered by

Ed. 2013/11




TESMEC’S LARGEST TORQUE CONVERTER EQUIPPED UNIT @ 440 HP FEATURES INDUSTRY LEADING HIGH CHAIN PULL AND VERY LOW CHAIN SPEED. ORIENTED TOWARD TRENCHING REQUIREMENTS IN HIGHLY ABRASIVE AND EXTREME ROCK CONDITIONS. TRENCHTRONIC 1.0 EQUIPPED.

1900

CAT 54/345 DIGGING LINK

CAT 54/345 DIGGING BP


TESMEC


TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC


TESMEC


TESMEC


TESMEC


TESMEC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LIN

K

TESM

EC

CAT 54/34

5 DIGGING LIN

K

TESM

EC

TESM

EC



TESMEC



TESMEC



TESMEC



TESMEC

CAT 54/345 DIGGING BP CAT 54/345 DIGGING LINK

TESMEC



TESMEC

CAT 5

4/345

DIGGIN

G BP

CAT 5

4/345

DIGGIN

G LINK

TESM

EC

CAT 54/

345 DIGG

ING BP

CAT 54/

345 DIGG

ING LIN

K

TESM

EC

CAT 54

/345 D

IGGING

BP

CAT 54

/345 D

IGGING

LINK

TESM

EC

CAT 54/

345 DIGGING BP

CAT 54/3

45 DIGGING LIN

K

TESM

EC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LINK

TESM

EC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LIN

K

TESM

EC

CAT 54/3

45 DIGGING BP

CAT 54/

345 DIGGING LIN

K

TESM

EC

CAT 54/3

45 DIGGING BP

CAT 54/

345 DIGGING LIN

K

TESM

EC

CAT 54/

345 DIGGING BP

CAT 54/3

45 DIGGING LIN

K

TESM

EC

CAT 54/

345 DIGGING BP

CAT 54/3

45 DIGGING LIN

K

TESM

EC

CAT 54/

345 DIGG

ING BP

CAT 54/

345 DIGG

ING LINK

TESM

EC

CAT 54/3

45 DIGGING BP

CAT 54/3

45 DIGGING LIN

K

TESM

EC

CAT 54/3

45 DIGGING BP

CAT 54/3

45 DIGGING LIN

K

TESM

EC

CAT 54/

345 DIGGING BP

CAT 54/

345 DIGGING LIN

K

TESM

EC

CAT 54/

345 DIGGING BP

CAT 54/3

45 DIGGING LIN

K

TESM

EC

CAT 54/34

5 DIGGING BP

TESM

EC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LIN

K

TESM

EC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LIN

K

TESM

EC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LIN

K

TESM

EC

CAT 54/34

5 DIGGING BP

CAT 54/34

5 DIGGING LIN

K

TESM

EC



TESMEC



TESMEC


TESMEC


TESMEC


TESMEC


TESMEC



TESMEC


TESMEC


TESMEC

TESMEC

CAT 54/34

5 DIGGING LIN

K

ADJUSTER

TRACKRECOIL

Tre

nch

er

TESM

EC





TESMEC


TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC


TESMEC


TESMEC


TESMEC


TESMEC



TESMEC



TESMEC



TESMEC



TESMEC

CAT 5

4/345

DIGGIN

G BP

CAT 5

4/345

DIGGIN

G LINK

TESM

EC

CAT 54/

345 DIG

GING B

P

CAT 54/

345 DIG

GING L

INK

TESM

EC

CAT 54/345

DIGGING BP

CAT 54/345

DIGGING LINK

TESM

EC

CAT 54

/345 D

IGGING

BP

CAT 54

/345 D

IGGING

LINK

TESM

EC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC



TESMEC


TESMEC



TESMEC

13

'-1

1"

[42

4cm

]

4'-4" [132cm]

2'-6" [76cm]

10'-4" [315cm]

(30" [76cm] PADS)

Min 30" [76.2cm]Max 42" [107cm]

6'-

9"

[2

06

cm]

10'-7"[323cm]

13'-3"[404cm]

1'-

8"

[51

cm]

11

'-1

0"

[36

1cm

]

"B"

"A"

13

°

9'-10" [300cm]

(24" [61cm] PADS)

11

'-6

" [3

51

cm

]

Trencher

TESMEC

Trencher

TESMEC





M5 ChainsawSpecification

Hydraulic TransmissionPressure and flow compensated (load sensing)Pump flow maximum...................45 gpm (170 l/min)Pressure setting...........................2.500 psi (172 bar)Oil tank capacity.....................................97 gal (367 l)

Standard FeaturesPressurized cab with air conditioning, heating, sound suppressionElevating cab module with roll over protection (ROPS)Load control: automatic optimal digging performance featureBattery box and toolbox with locking doorHydraulic tank: pressurized with 5 psi (0.30 bar) filtered breathersVibration isolator mount: used on engine, radiator, oil cooler, and exhaust silencerStabilizers / dirt drags: automatically adjust to terrain changesLights: 24 V forward facingDigging chain boom top rollerHydraulic digging chain adjustmentElectrical system: 24 V starting, 24 V controls

EngineModel.......................................CAT C13 ACERT Tier 3Max horsepower..............................440 hp (328 kW)Max no load rpm........................................2.100 rpmFuel tank capacity........................405 gal (1.533 l)Fuel consumption.....................22.7 gal/hr (86 l/hr)at full load Cooling rating adequate for 122° F (50° C) ambient air temperatureAir cleaner: dry type, centrifugal pre-cleaner with primary and secondary fi lters

Operating and Transport WeightWeight.....140,000-161,000 lbs (63.502-73.028 Kg)Note: weight calculations based on Cat chain with 1 ¾” baseplates

Crawler DriveDual path, hydrostatic drive, planetary transmissions capable of full counter rotation with single lever steering, single lever directionInfinitely variable speed: forward and reverseSpeed ranges:• High range......................0-2.4 mph (0-3.84 km/hr)• Low range......................0-1.3 mph (0-2.08 km/hr)Integral parking and service brake: spring applied, hydraulic release, wet disc brake

TracksOverall track length ...........................13’ 3” (404 cm)Track pad type: single, double or triple grouserTrack chain type: Caterpillar D7Track pad width.......................................30” (76 cm)

Trencher DriveThis powertrain is comprised of several components: an electronically controlled transmission driving a heavy-duty differential, which transmits power to the headshaft via sprockets and multi-strand roller chainFour operator selectable digging speed ranges:....................................1st: 98-197 fpm (30-60 m/min).................................2nd: 129-259 fpm (39-79 m/min)...............................3rd: 180-361 fpm (55-110 m/min)...............................4th: 246-492 fpm (75-150 m/min)Cutters: rotary carbide tipped 1 ½” (3.81 cm) shank diameterNote: chain speed are “as calculated” per a set-point horsepower output and may vary accordingly

Transport DimensionsLength without crumbshoe:.....................................6 ft boom: 39’ 7” (1.206 cm)...................................8 ft boom: 41’ 11” (1.278 cm)...................................10 ft boom: 44’ 1” (1.344 cm).................................12 ft boom: 46’ 11” (1.430 cm)...................................14 ft boom: 49’ 1” (1.496 cm)...................................16 ft boom: 49’ 2” (1.499 cm) without crumbshoe (non available for 16’ boom)Widths:.........16’ 4” (315 cm) with 30” (76 cm) track pads.........9’ 10” (300 cm) with 24” (61 cm) track padsHeight with cab..............................11’ 6” (351 cm)Height with cab elevated .............13’ 11” (424 cm)Height with crumbshoe...................11’ 10” (361 cm)

Trenching DimensionsDepths 6’ through 16’ (183 cm through 488 cm)Depths:......................30”-42” (76-107 cm) max 6’ (183 cm)......................30”-42” (76-107 cm) max 10’ (305 cm)......................30”-42” (76-107 cm) max 14’ (427 cm).....................30”-36” (76-91.5 cm) max 16’ (488 cm)Cut widths based on 14” chain centers

Available DevicesWork light package: 24 V, for night useLaser control system pre-wireHydraulic crumbshoeCab anti-vandalism window coversAir compressor

Cross ConveyorHydrostatic: one pump and two motorsReversible and shiftableBelt speed infinitely variable.......................................0-1.000 fpm (0-305 m/min)Discharge direction: right or leftConveyor belt width............................2’ 6” (76.2 cm) Conveyor length.................................12’ 9” (389 cm) Discharge height..................................6’ 9” (206 cm)

TransmissionModel: caterpillar Oil filter: 6 micron paper cartridge integral filterElectronically controlled utilizing (5)digging speedsCapacity (refill).....................................10 gal (38 l)


6’ 6’ (183 cm) 39’-7’’ (1206 cm)

8’ 8’ (244 cm) 41’-11’’ (1278 cm)

10’ 10’ (305 cm) 44’-1’’ (1344 cm)

12’ 12’ (366 cm) 46’-11’’ (1430 cm)

14’ 14’ (427 cm) 49’-1’’ (1496 cm)

16’ 16’ (488 cm) 49’-2’’ (1499 cm)** Boom 16’ W/O crumbshoe

Date post:	18-Mar-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

Main Technical Speciﬁ cations Trenchers for Pipeline ......0500 oil level mod.41t-140-sae oil...

Documents