Izod (Core item) Short sleevesStyle no.: 4597399 (Core color) & 45973xx Range (Fashion color)

Prepared on : August 2, 2006Revised on : January 23, 2008

PHILLIPS-VAN HEUSEN FAR EAST LIMITED

PRODUCT SPECIFICATIONS

2-3/4"3"

*FABRIC : PIQUE*CONTENT : 100% COTTON*WEIGHT : 220 GSM*YARN SIZE : 20'S/1 W/BIO WASH (SILKWASH)

*DYE : PIECE DYE*BUTTON : MULTI CHOICE EMSIG#5263,20L

BUTTONNECK 1 FRONT 1 EXTRACUFF POCKETSLEEVE PLACKET COLLAR

LINING

EDGE STAY

INTERLINING

COLLAR

REINFORCEMENTEND LININGBAND

CUFFS

POCKET TIP

LEFT FRONTRIGHT FRONT

PACKAGING

COLLAR SUPPORT

INSERT BOARD

COLLAR STRIP

TISSUE PAPERBUTTERFLYSTAINLESS STEELPIN

JET CLIP

POLYBAGFOLD SPEC

FREUDENBERY #8013T (NON WOVEN)

NILNILNILNILNILNIL

NILNILNIL

NIL

YES11" x 14"

NIL

NIL

Date : August 18, 2006VENDOR

YOKE/BACK

STITCHING AT BOTTOM

SIDE VENTRIGHT FRONT LEFT FRONT

COLLAR : 1 x 1 FLAT KNIT

BAND : NONE

NECK TAPE

IZOD CORE ITEM

X-STITCH

SEASON DIVISION IZOD PROGRAM

3/8" self fabric neck tape

1/16"T.S.

(12 SPI)

1/2"

FREUDENBERY #8013T(NON WOVEN)

SWEAT PATCH : SELF FABRIC

Inside view of sweat patch

Edge + 1/4" T.S.(12 S.P.I.)

1-1/2"

6 1/4"

1/4"

1/2"2-3/4"1/16" T.S.(12 SPI)

NIL

1/16" T.S.

4 THREADMOCK SAFETYOVERLOCK(10 - 12 SPI)

2 NEEDLE 3 THREADCOVERSTITCH

(10 SPI)

W/BACK TACKAT BEGINNINGAND END

Double turned back

....

.... .... 2 3/4"

3"

1/4" T.S.(12 SPI)

2"

1" HEM

1/4" T.S.(12 SPI)

W/STRAIGHTTAPE (SET TOBACK SIDE OF

SEAM) 1/4" T.S.

1" HEM1 X 1 FLAT KNIT

SIDE SEAM

Frontview

Backview

1/4"

5/8"

FREUDENBERY #8013T(NON WOVEN)

1/4"

SP'03 & onward

1/4" T.S.

FREUDENBERY #8013T (NON WOVEN)FREUDENBERY #8013T (NON WOVEN)

Refer to folding directive

Refer to folding directive

12

3

4

5

6

7

88

9

10

11 12

13

14

1516

17

18

19

20 21

2223

24

25

26 27

Revised Date : February 08, 2007XSM

28 ½

29 ½

18

17

2 1/8

5/8

20 1/4

16

20 1/4

1

9 3/4

8 ½

10 1/8

5 3/4

1

3 3/8

½

15 ½

14 ½

3

2 3/4

4

6 ½

1 ½

6 1/4

2

3

SM

29

30

18 ½

17 ½

2 1/8

5/8

21

16 ½

21

1

10

8 3/4

10 1/4

6

1

3 ½

½

16

15

3

2 3/4

4

6 ½

1 ½

6 1/4

2

3

M

30

31

19 ½

18 ½

2 1/8

5/8

22 ½

17 ½

22 ½

1

10 ½

9 1/4

10 ½

6 ½

1

3 3/4

½

17

16

3

2 3/4

4

6 ½

1 ½

6 1/4

2

3

L

31

32

20 ½

19 ½

2 1/8

5/8

24

18 ½

24

1

11

9 3/4

10 3/4

7

1

4

½

18

17

3

2 3/4

4 ½

6 ½

1 ½

6 1/4

2

3

XL

32

33

21 ½

20 ½

2 1/8

5/8

25 ½

19 ½

25 ½

1

11 ½

10 1/4

11

7 ½

1

4 1/4

½

19

18

3

2 3/4

4 ½

6 ½

1 ½

6 1/4

2

3

XXL

32

33

22 ½

21 ½

2 1/8

5/8

27

20 ½

27

1

12

10 3/4

11 1/4

8

1

4 ½

½

20

19

3

2 3/4

4 ½

6 ½

1 ½

6 1/4

2

3

XXXL

33

34

23 ½

22 ½

2 1/8

5/8

28 ½

21 ½

28 ½

1

12 ½

11 1/4

11 ½

8 ½

1

4 3/4

½

21

20

3

2 3/4

4 ½

6 ½

1 ½

6 1/4

2

3

Tol (-/+)

½

½

½

½

1/8

1/8

½

½

½

1/8

1/4

1/4

1/4

1/4

1/8

1/8

1/8

1/4

1/4

1/8

1/8

1/8

1/8

1/8

1/8

1/8

1/8

1. FRONT LENGTH FROM HPS

2. BACK LENGTH FROM HPS

3. SHOULDER WIDTH - SEAM TO SEAM

4. ACROSS BACK 6” FROM HPS

5. SHOULDER SLOPE

6. FORWARD SHOULDER SEAM FROM HPS

7. CHEST 1” BELOW ARMHOLE

8. ACROSS CHEST 6” FROM HPS

9. BOTTOM OPENING - SWEEP

10. BOTTOM TRIM / HEM HEIGHT

11. ARMHOLE STRAIGHT - SEAM TO SEAM

12. MUSCLE 1” BELOW ARMHOLE

13. SLEEVE LENGTH FROM ARMHOLE

14. SLEEVE OPENING AT EDGE

15. SLEEVE TRIM HEIGHT

16. FRONT NECK DROP FROM HPS TO SEAM

17. BACK NECK DROP FROM HPS TO SEAM

18. NECK CIRCUMFERENCE AT SEAM / EDGE RELAXED

19. COLLAR LENGTH - EDGE

20. COLLAR HEIGHT - CENTER BACK

21. COLLAR POINT

22. SWEAT PATCH HEIGHT

23. SWEAT PATCH WIDTH

24. PLACKET WIDTH

25. PLACKET LENGTH

26. VENT / SLIT OPENING HEIGHT - FRONT

27. VENT / SLIT OPENING HEIGHT - BACK

Label location

*For model with sweat patch : label stitching should not show through the garment

*White ground w/black wording*Printed ribbon label

Care/PC Label location :

Main label : IML - 2137 (layout)

*NAVY GROUND WITH SILVERWORDING

*TO BE STITCHED ON TWO ENDSIDES WITH MATCHING STITCHING

*ACTUAL SIZE : 1-5/8" (W) X 21/32" (L)

Content label : ICL-1535 (layout)

1-5/8"

21/32"

*Loop label*Navy ground with silver

wording (match to main label)

Care/PC label : IPL-100 (layout)

*Style no./factory code/Seasoncode and care instruction : variousdepending on differentrequirement

*White ground w/black lettering*Size : 1" width, height size adjust

based the wording of care

Centerline

Main label1/2" Content label

3/4"

Depend onthe productionarea

Fabriccontent

SizeFold line

3"

Care/PC label

3" up from top of side ventat left side seam as worn

(inside of garment)

Hangtag location : For wholesale & retail order

*The Izod logo hangtag with upc sticker : to be swift tacked to the back side ofcontent label with 3” plastic pin

Izod logo hangtag withupc sticker (logo face up

when looking at the garment)

Streamer

Streamer : IML-2210 ( layout)

*Navy ground with silver wording*To be stitched on 2 end sides withmatching stitching, below the mainlabel

Date : August 18, 2006

. .40C. .

MACHINE WASH WARM

GENTLE CYCLE

WITH LIKE COLORS

ONLY NON-CHLORINE

BLEACH WHEN NEEDED

TUMBLE DRY LOW

REMOVE PROMPTLY

STEAM IRON

PC759

Fold line4597299

W44

S

Pc code

Style no.Factory code

Season code

. .

*The vendor must not alter any of the wordingpreprinted on the upc sticker

*Style #/color #/size : please refer to our merch.department

*No adhesiveon this portion

Hangtag : IHT-3769 (for wholesale and retail order) UPC sticker : for wholesale order

(Front view) (Back view)

Revised Date : August 22, 2006

EMBROIDERY PLACEMENTCOLOR COMBINATION OF EMBROIDERYref #SP07-TD-39 Version #1”

8-1/2" down from HPSto top of crest

3-1/2" from centerfront of gmt to edge of emb.

*Actual color combo of embroidery : please referto the seperate instruction from our merchandisingdept

Date : August 18, 2006

*POLYBAG QUALITY: PE 0.4*POLYBAG THICKNESS : MIN 0.75MIL / MAX 1.25MIL*POLYBAG SIZE : 14 1/2" (LENGTH) X 12" ( WIDTH )

*WORDINGS IN NAVY COLOR

*THE VENDOR MUST NOT ALTER ANY OF THE WORDING PREPRINTEDON THE POLYBAG STICKER

POLYBAG : IZK-3

(BACK VIEW OF POLYBAG) (FRONT VIEW OF POLYBAG)

WARNING: To avoid danger of suffocation, keep this bag away from babies and children.

Do not use in cribs, beds, carriages, or playpens. This bag is not a toy!

RN 36543

Polybag sticker : VN93

*Polybag sticker (For wholesaleorder only) : to be stuck to theright bottom corner of frontpolybag

1”

1 “

Polybagsticker

Polybagopening

04

PE

For wholesale order Revised date : January 23, 2008

Clear size sticker : For Izod wholesale & JCP order only

*Clear size sticker location : wrapped aroundfront and the back evenly (2-1/2" from center front)

as sketch illustrated

(Front view)

2-1/2"

........

Flat fold

Clear size sticker location for WHOLESALE

(Back view)

IMS-3066W (white wording)IMS-3066B (black wording)

*For all fabric except polar fleece*5" (length) x 1-1/2" (width)*Ground color : Transparency*Wording color : black (for light color garment)

white (for dark color garment)

FOLD SIZE: 11" X 14"- NO PIN- NO TISSUE PAPER- ASSURE GARMENT IS CENTRE OF PACKAGE AND EMBROIDERY IS SHOWN ON FACE OF FOLDED SHIRT.

Folding method

14"

11"

(Front) (Back)

FOLD LINE

FOLD LINE

For wholesale order

Packing instruction for IZOD WHOLESALE shipments to "Reading warehouse"

Height

Length

Wid

th

*Alternate collar position every three garments*Dozens per carton : please refer to the seperate

instruction from our merchandising dept.*Garments that overlap one another*Carton dimension should be 24” (L) x 17” (W) x 10” (H) : 34 pcs/carton

13"

6"

(Side 2)

Perforatedwindow

Revised date : March 16, 2004

Directive Ref: ALL-SHIP-AL-002 [Final Version] DATE: OCT 10, 2002.

Last Revised Date: Mar 23, 2005

SHIPPING CARTONS PHYSICAL REQUIREMENTSFOR 'READING' WAREHOUSE: FOR WAREHOUSES OTHER THAN 'READING':WEIGHT : NO CARTON CAN EXCEED 40 POUNDS WEIGHT : NO CARTON CAN EXCEED 40 POUNDS

CARTONS SHOULD WEIGHT AT LEAST 2 POUNDS.

GIRTH : FOR BULK PACK 10 LBS. MINIMUM IS PREFERRED.MIN. MAX.24" 29" GIRTH:

17" 18" SMALLEST IDEAL LARGEST

12" 13" 10" 22" 36"

GIRTH : FOR WOVENS WITH INNER BOXES 8" 22" 24"

MIN. MAX. 4" 16" 24"

24" 32" NOTE:

17" 25" -Carton width never exceeds carton length.

10" 12" -Height should not exceed the lesser dimension of length or width by more than 10%

NOTE: Strapping: - The use of plastic/metal strapping is not acceptable for PVH.

STANDARD SHIPPING MARKS FOR ALL DIVISIONS

*Remarks : STYLE/COLOR NO. should show the same as on the purchase order.

EXAMPLE:

32 - N9002 - 432

* Shipping mark in the upper left hand corner on two adjoining side

(SIDE 1 and SIDE 3),lettering must be printed in ink (or stencilled),

not hand written with a ball point pen, and be a minimum of 3/4"

high. The font used should result in a width of at least 2 1/2"

for a five digit number. In case the carton is too small to

accommodate the above 'shipping mark', the font size should

be proportionally reduced to fit the carton size.

SHIPPING CARTON QUALITY- DOUBLE WALL (2 LAYERS OF CORRUGATED BETWEEN 3 LAYERS OF KRAFT LINER BOARD).

- 370 LB/SQ. INCH (26 KG/CM2) BURSTING STRENGTH.

T:\USERDATA\HKTECH\ANN\CTN MARKING\SHIPPING CARTON PHYSICAL REQUIREMENT & SHIPPING MARK - MAR 1, 05

Height

DIMENSIONLength

Length

SHIPPING MARKS PRINTING ON CARTONS (Side 1 & Side 3)

DIMENSION

Width

Height

Width

Height

DIMENSION

Length

Width

1/2"

Space/hyphen/Space

Division # Style # Color #

SHIPPING MARK : STY-COL #:SIZE:QTY:

PO #:MADE IN

(SIDE 2)(SIDE 4)

(SIDE 3)

(SIDE 1)

PREPARED ON : September 18, 2002

Directive Ref: SPT-CTNL-AL-001 REVISED ON : March 1, 2005

In order to facilitate the warehouse receiving process and storage capacity, please follow the Carton Label Location guideline illustrated below :

SPECIMEN OF CARTON LABEL WRAPCT06 FOR 'JONESVILLE' WAREHOUSE (NOT IN ACTUAL SIZE)A LINE WITH ARROWS AT BOTTOM & TOP OF LINE TO ILLUSTRATE WHERE TO

FOLD AND PLACE ON CORNER OF CASE.

Carton number is 9 digits

LONG PORTION (LEFT SIDE) = 5-1/4" SHORT PORTION (RIGHT SIDE) = 4-3/4"

FOLD LINE

** PLACE THE WRAP AROUND LABELS ON THE CORNER OF THE OUTER CARTON.

** LONG PORTION (LEFT SIDE) OF THE LABEL IS CONSIDERED "SIDE" AND SHORT PORTION (RIGHT SIDE) ON THE "END" AS SKETCH "A" ** PVH STANDARD FOR MINIMUM HEIGHT OF CARTON WILL BE 4" (EXCEPT CARTONS FOR 'READING').

** FOR THOSE CARTONS COULD NOT MEET 4" STANDARD HEIGHT SIZE, TOP PORTION OF WRAP AROUND LABEL WILL BE FOLDED OVER TOP AS SKETCH " B"

(A) (B)

T:\USERDATA\HKTECH\ANN\CTN MARKING\WRAP AROUND CTN LBL FOR JONESVILLE - 17 FEB, 2005.XLS

CARTON LABEL LOCATION

10"

WRAP AROUND CARTON LABEL LAYOUT & LOCATIONFOR ALL SHIPMENTS TO 'JONESVILLE' WAREHOUSE - (For Division : ALL RETAIL Direct Apparel (Izod/Van Heusen/Bass/Geoffrey Beene)

4"

PREPARED ON : FEBRUARY 17, 2005

Directive Ref: SPT-CTNL-AL-004 REVISED ON : MARCH 1, 2005

In order to facilitate the warehouse receiving process and storage capacity, please follow the Carton Label Location guideline illustrated below :

SPECIMEN OF CARTON LABEL WHSLCT01 (NOT IN ACTUAL SIZE)A LINE WITH ARROWS AT BOTTOM & TOP OF LINE TO ILLUSTRATE WHERE TO

FOLD AND PLACE ON CORNER OF CASE.

Carton number is 9 digits

LONG PORTION (LEFT SIDE) = 5-1/4" SHORT PORTION (RIGHT SIDE) = 4-3/4"

FOLD LINE

** PLACE THE WRAP AROUND LABELS ON THE CORNER OF THE OUTER CARTON.

** LONG PORTION (LEFT SIDE) OF THE LABEL IS CONSIDERED "SIDE" AND SHORT PORTION (RIGHT SIDE) ON THE "END" AS SKETCH "A" ** PVH STANDARD FOR MINIMUM HEIGHT OF CARTON WILL BE 4" (EXCEPT CARTONS FOR 'READING').

** FOR THOSE CARTONS COULD NOT MEET 4" STANDARD HEIGHT SIZE, TOP PORTION OF WRAP AROUND LABEL WILL BE FOLDED OVER TOP AS SKETCH " B"

(A) (B)

T:\USERDATA\HKTECH\ANN\CTN MARKING\WRAP AROUND CTN LBL FOR ALL WAREHOUSES EXCEPT JONESVILLE - 17 FEB, 2005.XLS

WRAP AROUND CARTON LABEL LAYOUT & LOCATIONFOR ALL SPORTSWEAR (WHOLESALE) SHIPMENTS TO BRINKLEY / SCHUYLKILL HAVEN / CHATTANOOGA / AUSTELL / READING

CARTON LABEL LOCATION

10"

4"

PREPARED ON : September 18, 2002

Directive Ref: ALL-CTNL-AL-001 REVISED ON : February 17, 2005

In order to facilitate the warehouse receiving process and storage capacity, please follow the Carton Label Location & the Color Sticker Placement guideline illustrated below :

** RED COLOR GROUND WITH BOLD WHITE FONT. ** COLOR STICKER IS PRE-PRINT WITH "NON-CONFORMING * THE 'NON-CONFORMING CARTON' STICKER SHOULD BE PLACED ON THE 'SIDE 2' (SHORT

CARTON", TO BE PUT ON "SIDE 2" (SHORT PORTION - PORTION - END) OF THE OUTER CARTON. PLACEMENT IS 1" TO THE RIGHT EDGE OF THE

END) AS SKETCHES ILLUSTRATED CARTON LABEL (SKETCH A). IF THE OUTER CARTON IS NOT BIG ENOUGH, THE RED COLOR STICKER

(NOTE: JUST IN CASE THE CARTON SIZE IS NOT BIG CAN BE PLACED TO THE TOP OF THE CARTON LABEL AS (SKETCH B1) OR (SKETCH B2).

ENOUGH, THE RED COLOR STICKER CAN BE PLACED (NOTE: NO MATTER WHETHER IT IS A NON-CONFORMING CARTON, NEVER CROSS OUT THE

TO THE TOP OF THE CARTON LABEL.) BAR CODED PRINTING ON THE CARTON LABEL.)

'FONT' & 'LETTER SIZE' OF THE WORDING ON THE COLOR STICKER": A) FONT = TIMES NEW ROMAN (BOLD) LETTER SIZE = AT LEAST 3/8" HIGH

4"

4" B1) B2)

REMARKS: COLOR STICKER TO BE PREPARED BY THE FACTORY.T:\USERDATA\HKTECH\ANN\CTN MARKING\WRAP AROUND CTN LBL FOR JONESVILLE - 17 FEB, 2005.XLS

SCHUYLKILL HAVEN / CHATTANOOGA / READING & AUSTELL)

COLOR STICKER IDENTIFICATION FOR "NON-CONFORMING" CARTONL SHIPMENTS TO 'JONESVILLE' WAREHOUSE - (For Division: Dress-Wholesale-Production for Van Heusen and Geoffrey Been

SPECIMEN OF THE COLOR STICKER (ACTUAL SIZE) FOR ALL SHIPMENTS TO ALL WAREHOUSES (JONESVILLE / BRINKLEY /

REVISED DATE : FEBRUARY 23, 2005

SECURITY SEALING TAPE ON CARTON

DIRECTIVE REF : ALL-PACK-AL-002 (REV. 2)

SPECIMEN OF SEALING TAPE (LOGO - Placed at center of sealing tape. 1/2" height)

72mm

SECURITY SEALING TAPE WITH “LOGO”

SIZE AND QUALITY :

COLOR :

72MM WIDTH , POLYPROPYLENE

TRANSPARENT;

PVH WARNING LOGO AND WORDINGS - BLACK

Bottom edge of the the Wrap Around Carton Label placed

½”from bottom of the carton. Please note the

“SECURITY SEALING TAPE” cover the

carton label.

CANNOT

SEALING TAPE ON THE CARTON :

WRAP AROUND CARTON LABEL

TRANSPARENT SECURITY

TAPE COVERED THE CARTON LABEL

THE CARTON LABEL IS NOT COVERED BY

THE TRANSPARENT SECURITY TAPE

INCORRECTCORRECT

SHIPPING CARTON TO “READING” WAREHOUSE - WITH “PERFORATED WINDOW”

*THE “SIZE” & “PLACEMENT” OF THE PERFORATED WINDOW*

For all divisions that have goods going into “Reading”.

Goods including :

1. ALL PICK/PACK GOODS (INCLUDING JCP CATALOG)

2. ALL KNITS, SWEATERS, BOTTOMS,WOVEN SHIRTS.

: THE PERFORATED WINDOW IS FOR ANY PRE-PACKS (SPECIALS

& JCP RETAIL) GOODS AND EXCEPTION FOR PERU .

: ON “SIDE 1” OF THE EXPORT CARTON.

3. SHIPPING MARK IS ALLOWED TO PRINT ON TOP OF THE PERFORATED WINDOW

NOTE NOT REQUIRED

PLACEMENT

For all divisions that have goods going into “Reading”.

Goods including :

1. ALL PICK/PACK GOODS (INCLUDING JCP CATALOG)

2. ALL “ ” ONLY

: THE PERFORATED WINDOW IS FOR ANY PRE-PACKS (SPECIALS

& JCP RETAIL) GOODS AND EXCEPTION FOR PERU.

: ON “SIDE 1” OF THE EXPORT CARTON.

OUTERWEAR

NOTE NOT REQUIRED

PLACEMENT

6"

18-1/2"

Revised date : April 11, 2005

T:\userdata\hktech\sportswear\directive\izodmen\perforated window.cdr

Perforated window

6"

13"

Shippingmark

(Side 2)

(Side 4)

(Side 1)

-----------------------------------------------------

(Side 3)Shipping mark

1”

Perforated window

Shippingmark

(Side 2)

(Side 4)

(Side 1)

-----------------------------------------------------

(Side 3)Shipping mark

1”

STANDARD FORMAT & PLACEMENT OF “PACKING SLIP” FOR MIXED SIZE CARTON

PACKINGSLIPEXAMPLE:

2

–

–

–

– 6

–

–

–

–

–

–

–

–

–

–

4

–

--

–

8

–

–

–

(S) (M) (L) (XL) (XXL)

THEQUANTITYANDSIZEOFTHEUNITSINCARTONSHOULDBEDETAILEDONTHEPACKINGSLIP.

APPROX6”

APPROX10”

Incase the cartoncannot be packed as ourstandard packing requirement and have topackinassorted sizes per single lot base, a large wording o f “ASSORTED” (AT LEAST 1”must be marked on outside of carton adjacent to the shipping mark - “ size” column.It is most important that a “PACKINGSLIP” withthequantity and size info o f t h eun i t s i nthe carton must be put on the carton as the identifer of “MIXEDSIZE” Carton. (See format above)

-The PACKING SLIP should be put on the “END” panel(Side 2) next to the short portion of the wrap around Barcoded Carton label.

(NOTE : IF THE CARTON IS TOO SMALL TO PROVIDE ENOUGH SPACE FOR THEPACKING SLIP, YOU COULD ADJUST THEPACKING SLIP MEASUREMENT TOACCOMMODATE THE AVAILABLE AREA. THE PACKING SLIP CAN COVER THESHIPPING MARK, BUT NOT ONTHE “CARTON LABEL”.)MUST

HIGH)

REVISEDDATE:MARCH1,2005.

(SHORTPORTION- )END

1/2"

(SIDE3)(SIDE2)

(SIDE4)(SIDE1)

(LONG PORTION- )SIDE WRAPAROUND

CARTONLABEL

PACKINGSLIP

PLACEMENTOFTHEPACKINGSLIP:-FOR“ALL”WAREHOUSE

PACKINGSLIPPUT ONSIDE2(END)NEXTTOTHESHORTPORTIONOFTHEBARCODED CARTON LABEL.

FOR ALL SPORTSWEAR SHIPMENTS

DIRECTIVE REF : SPT-PACK-AL-002