1 <<Contents>> Installation Manual -SmartDVR Formula™ Hardware Installation -SmartDVR Formula™ Software InstallationUser Manual -SmartDVR Formula™ Surveillance Mode -SmartDVR Formula™ Search Mode -SmartDVR Formula™ AVI Backup Manager Mode -SmartDVR Formula™ Backup Manager -SmartDVR Formula™ NetClient Mode -SmartDVR Formula™ WebClient Mode-SmartDVR Formula™ PDA NetClient ModeCompatible / Incompatible SmartDVR Formula™ Hardware Installation 2 When you purchase INTOTECH DVR, you have to install DVR board in user’s PC or DVR system. This is an installation guide for Capture board among INTOTECH DVR boards. Minimum Requirement DVR Board S SP H HP Live120 Live480CPU CEL 1.7Ghz or higher P4 2.8C Ghz or higherCEL 2.4 Ghz or higher P4 2.8C Ghz or higher RAM 256 MB or higher 512 MB or higher HDD 80 GB 7200rpm or higher Motherboard Intel i845G Chipset built-in motherboard Ref In case of using analog audio, we recommend to use Intel i865 Chipset built-in motherboard. VGA Refer to 128page OS Only Windows 2000™, Windows XP™ (Windows 98™ & ME not supported)

Direct X DirectX 8.1 or higher SmartDVR Formula™ Hardware Installation 3 □1 DVR board & Extension video cable installation Insert the DVR board to an empty PCI slot in the motherboard of your computer or DVR system. □2 Video & Audio connection Video input installation Extension Cable Type DVR board: Connect your camera to the DVR board using a 4-channel or 8-channel video extension cable. BNC Type DVR Board: Connect the image line (composite) directly to the DVR board. SmartDVR Formula™ Hardware Installation 4 Audio input installation MIC IN port of motherboard. Connect the microphone to the MIC IN port of your motherboard .Audio IN port of DVR board. Connect the microphone to the Audio IN port of DVR board. Connecting microphones with more than 4-channel Each DVR board supports multi-channel microphone input as given in the following table. When using microphone input with more than 2-channel, additional audio extension cables are required. Specific directions for each board are listed in the next two page. Board Analogue audio Digital audio Sound Card S 1ch - 1ch SP 2ch 4ch 1ch H 4ch - 1ch HP 8ch - 1ch Live120 X 4ch 1ch Live480 X 8ch 1ch SmartDVR Formula™ Hardware Installation 5 - S board S board supports only 1ch microphone input. No need for extension cables. - SP board SP board supports 2ch microphone input. Refer to the figure on the right. Only two ports are actually used in the audio extension cable. - H board H board supports 4ch microphone input. Refer to the figure on the right. SmartDVR Formula™ Hardware Installation 6

- HP board HP board supports 8ch microphone input. Refer to the figure on the right. Connect the 8ch audio extension cable (B) with the connector on the DVR board. Make sure to connect the cable to the upper part (A) of the connector as shown in the figure. Digital audio installation Audio quality of digital audio board is superior to the quality of analogue audio. You have to purchase the digital audio board. Digital audio board is compatible with SP board and Live Series board only. SmartDVR Formula™ Hardware Installation 7 □3 P/T/Z Installation Some cameras support pan/tilt/zoom/focus function. In order to use P/T/Z camera, you need to connect P/T/Z cable. [A] connecter: Connect P/T/Z cable to COM port of the DVR systems [B] connecter: Connect P/T/Z cable to the DVR board. [C] part: Connect to receiver (camera). When using more than one camera, connect cables as shown in the figure below. SmartDVR Formula™ Hardware Installation 8 Ref P/T/Z cable Connection for each board. □4 I/O board installation If you choose to install the additional I/O board on your DVR system, various sensors and alarms can be connected. The I/O board supports 4IN/3OUT. With an I/O extension board with 4IN/OUT, one set of <I/O board + I/O extension board> can support 8IN/8OUT. A maximum of 16IN/16OUT is supported with two sets of <I/O board + I/O extension board> SmartDVR Formula™ Hardware Installation 9 Back panel connection port in industrial systems. For industrial systems, the IN/OUT port can be used separately by adding a back panel to the DVR system case. Connection port of I/O extension board cable. Connect to the I/O extension board. DVR board connection port Connect to the DVR board in the DVR system. Master/Slave connection port

You can use up to 8-channel with an I/O extension board (4IN/5OUT) connected to a I/O board (4IN/3OUT). Refer to the figure below for connection guidelines. If 16-channel is required, use two sets of <I/O board + I/O extension board>. See Master/Slave setup dip jumper on the next page. SmartDVR Formula™ Hardware Installation 10 Master/Slave setup dip jumper When using more than one I/O board, use jumpers to designate Master/Slave. (Master: Jumper install / Slave: Jumper uninstall) E.g. An example of a connection between a DVR board and two sets of <I/O board + I/O extension board> (see figure below) SmartDVR Formula™ Software Installation 11 Software installation manual overview SmartDVR Formula™ SmartDVR Formula™ is a program for operating INTOTECH DVR system. It should be installed on all systems using INTOTECH DVR Board, and is required for running other software that INTOTECH provides. NetClient NetClient must be installed to allow remote monitoring activities. With INTOTECH DVR system, it is possible to connect directly to the DVR system with an internet connection, and monitor or record transferred images. It connects to the 20408 port of the DVR system and allows you to monitor and control the system. WebClient WebClient must be installed to provide surveillance images on the web. INTOTECH DVR system allows you to connect to the DVR system on the web. Users can monitor and use P/T/Z functions of surveillance cameras. Once WebClient is installed on the DVR system, connection for individual users will be very convenient. When a user connects to the DVR system on a website, WebClient install file is automatically downloaded through the 26540 port and automatically installed on the computer. SmartDVR Formula™ Software Installation 12 Software InstallationINTOTECH SmartDVR Formula™ can be installed from the provided SmartDVR Formula™ CD-ROM or downloading the installation file from INTOTECH website. www.intotech.co.kr. The software CD contains the Server Package consisting of Main program, WebClient program, NetClient, and AVI codec. User manual is also available in the software CD.

1. DVR Server Package Installation Insert SmartDVR Formula™ CD into a CD-ROM drive or run DvrSetup.exe file; the following installation screen will appear. Click on the first button to begin the DVR Server package installation. SmartDVR Formula™ Software Installation 13 SmartDVR Web installation Click ‘Install Server Package’ button to proceed with the installation. SmartDVR Formula™ Installation After Installation Shield Wizard opens, click [Next]. Read the License Agreement, and click [Yes] if you agree. SmartDVR Formula™ Software Installation 14 Check the added or modified functions of the DVR Server version being installed and click [Next]. After choosing [Destination Folder] for installation, click [Next]. SmartDVR Formula™ Software Installation 15 After the installation is done, click [Finish]. Driver Installation: Wizard automatically installs drivers according to each board type.Please reboot PC after the installation is complete. SmartDVR Formula™ Software Installation 16 SmartDVR Formula™ Uninstallation Before upgrading SmartDVR Formula™ to a newer version, or if there is a problem in the current version, please remove the current version by the following method. Note For DVR system stability, SmartDVR Formula™ and other programs must be removed or modified by the following process. Click the Windows [Start] button. Click on the Control Panel. (For different operating systems, there may be different ways of opening the Control Panel. ) Click [Add/Remove Program]. Click on SmartDVR Formula™. Click [Add/Remove Program] 2. NetClient InstallationIn the setup program offered in the CD, Click on ‘Install Client Package’ button to begin installation. SmartDVR Formula™ Software Installation 17 After Installation Shield Wizard opens, click [Next]. After choosing [Destination Folder] for installation, click [Next].SmartDVR Formula™ Software Installation

18 After the installation is complete, click [Finish]. NetClient Uninstallation Before upgrading SmartDVR Formula™ to a newer version, or if there is a problem in the current version, please remove the current version by the following method. Note For DVR system stability, SmartDVR Formula™ and other programs must be removed or modified by the following process. Click the Windows [Start] button. Click [Control Panel]. (For different operating systems, there may be different ways of opening the Control Panel. ) Click [Add/Remove Program]. Click [NetClient]. Click [Add/Remove Program] SmartDVR Formula™ Software Installation 19 3. AVI Codec Installation INTOTECH AVI codec must be installed for watching surveillance video files (backed up by AVI Backup Manager) on the DVR system or on other computers. Click ‘Install AVI Codec’ to begin AVI Codec installation. Figure: AVI Codec Installation window. SmartDVR Formula™ Software Installation 20 After the installation is complete, click [Finish]. Ref: SP Digital Audio Installation (Window 2000) In case of using digital audio in SP60 DVR systems with Windows 2000, Digital Audio Driver must be installed manually by the following process. Open the Device Manager. [Start>Control Panel>System>Hardware>Device Manager]. SmartDVR Formula™ Software Installation 21 Double-click [Digital Video Recording System]. Right-click [WDM DVR Audio Driver] and choose [Driver update]. Ref If you see the screen below, choose the [Yes, this time only] and then click [Next] Choose [Install from a list or specific location(Advanced)], and click [Next]. SmartDVR Formula™ Software Installation 22 Select [Search for the best driver in these locations.], and check the [Include this location in the search] box. Enter the following path. C:\Program Files\SFDVR\Driver\9x2k\SPLUS Click [Search]. Check the figure below to see if you have entered everything correctly. Click [Next]

Choose [WDM LIVE Audio Driver] and click [Next] SmartDVR Formula™ Software Installation 23 You will see a message that the Digital Audio Driver installation is complete. Click [Finish] After the installation, the Device Manager should look like the figure below. Proceed with the remaining [WDM DVR Audio Driver]s in the same way. SmartDVR Formula™ Software Installation 24 If the Digital Audio Driver installation has completed successfully, there will be two [WDM LIVE Audio Driver]s displayed in the Device manager. You must reboot the computer for the driver to operate properly. After rebooting the computer, run SmartDVR Formula™. (See the section on SmartDVR Formula™ manual.) Click Configuration. Click the [General] tab. If the installation was successful, Audio Devices 1 to 4 should be displayed as shown in the figure below. SmartDVR Formula™ Software Installation 25 If you want to use channels 1 to 4, and use the MIC jack of your audio card for channel 5, configure your audio as shown in the figure below. This particular case is for using video channels 1 to 5. Click [Apply] for the changes to take effect. SmartDVR Formula™ User Manual 26 SmartDVR Formula™ is the cornerstone program of ©INTOTECH DVR System. It carries out the most important functions and acts as a server for the other programs provided. SmartDVR Formula™ provides you with 1 to 9 audio channels (Supported channel widths vary with different boards) and a maximum of 16 video channels. Each channel supports either low resolution for less storage space or high resolution for more storage space. There are also 9 audio channels to be used as needed. Optimum images for different environments can be realized through the various split-screen display modes and color adjustment functions. Existing analog CCTV equipments such as Sensor & Alarm, P/T/Z camera, Video Out, etc. are perfectly compatible. Image or E-mail can be transmitted over the network for users to observe from remote sites without having to sit still in front of the DVR System. Up to 30 user accounts can be created to grant authorization at user-level, and allow real time monitoring over a network connection. SmartDVR Formula™ User Manual 27 Minimum Requirement

DVR Board S SP H HP Live120 Live480CPU CEL 1.7Ghz or higher P4 2.8C Ghz or higher CEL 2.4 Ghz or higher P4 2.8C Ghz or higher RAM 256 MB or higher 512 MB or higher HDD 80 GB 7200rpm or higher Motherboard Intel i845G Chipset built-in motherboard Ref In case of using analog audio, we recommend to use Intel i865 Chipset built-in motherboard. VGA Refer to 128page OS Only Windows 2000™, Windows XP™ (Windows 98™ & ME not supported)Direct X DirectX 8.1 or higher Min. Required Space when installation 30 MB Others Graphic Driver and Sound Card are required as compulsory. SmartDVR Formula™ User Manual 28 Before starting SmartDVR Formula™ for the first time… When you start SmartDVR Formula™ for the first time after the installation, a DVR EasySetting window will appear to let you configure the basic settings.

Camera Setup: Configure the cameras connected to the DVR ①system. A. Video Mode: Choose a video mode for the cameras. Note North America, Korea, Japan : NTSC Europe and other regions: PAL B. Camera Resolution: Choose the resolution of the video.

High-resolution (640x480 or 720x576) gives better images but more disk space is consumed. C. Connected Camera Setup: Check the boxes next to the channels that have cameras connected. SmartDVR Formula™ User Manual 29

Recording Device Setup: Choose a local hard disk drive to store ②the surveillance images.Choose a disk drive with a large free space that does not have an OS(Operating System) installed. If a disk drive with an OS installed is selected, the system will not have enough free disk space and could become unstable. Note If you do not choose any disk drive, [C drive] will be chosen by default.

Enable Windows Lock: Check this box if you wish to disable ③certain Windows functions or shortcut keys for security or safety reasons. When checked, the following functions and shortcut keys will become unavailable.After you finish configuring, click [Next] on the bottom right corner to start SmartDVR Formula™.Windows functions/Shortcut keys When lock is on Desktop Hide Start button Hide Taskbar Hide System Clock Hide Alt+Tab Disable Task Switching Keys(Alt + Tab) Disable Task Manager Disable Ctrl+Alt+Del Disable Ctrl+Shift+Esc Disable SmartDVR Formula™ Surveillance Mode 30 SmartDVR Formula™ Surveillance Mode □1 Control Panel □2 Screen Partition Panel □3 P/T/Z Control Panel □4 Channel Type Selection Panel □5 Real Time Audio Volume Control Panel □6 DVR Status Information Panel SmartDVR Formula™ Surveillance Mode 31 □1 Control Panel Users can run search program, record images, open configuration screen, etc. from the control panel. Search Button: Click to run search program. Configuration Button: Opens the configuration window, where you can change the system settings.Login & Log out Button:Log in/out function is supported to restrict access to configuration

settings and vital functions by anyone besides the administrator and allowed users. REC Button & All Button: To start recording a specific channel, click on the desired channel screen and click [REC]. To start recording all channels at once, click [ALL] and click [REC]. □2 Screen Partition Panel You can select a display mode from 7 different screen partitioning choices. Full screen mode is supported. If you enable the auto-switching function, the display will automatically cycle through different channels. SmartDVR Formula™ Surveillance Mode 32 □3 P/T/Z Control Panel P/T/Z Control Panel is for controlling cameras with P/T/Z functions. First choose the channel you wish to control by clicking on the screen of that channel. Then use the buttons in P/T/Z Control Panel to manipulate the camera in various ways – you can pan, tilt, zoom in/out, and change the focus. □4 Channel Status/ Selection Panel Click on a channel number to enlarge the channel video. □5 Real-Time Audio Volume Control Panel If audio input has been designated to each channel in [Configuration] - [General], you can use audio volume control bar to control the real-time audio volume. □6 DVR Status Information Panel Indicates the number of channels connected by Internet( TCP ) or Modem. When there is no more free space available in recording HDD, ‘Disk Full’ will be indicated in red color. SmartDVR Formula™ Surveillance Mode 33 Configuration Setup Configuration consists of detailed items characterized by functions and applications. You can choose setups for video resolution, image quality, motion detection recording, digital input/output, scheduling, P/T/Z receiver protocol, network, etc. General

Start Setup ①SmartDVR Formula™ can be configured to auto-start at Windows startup or when the DVR system is switched on.

Max Size at Starting ②Set SmartDVR Formula™ to open at full screen to prevent using other programs. SmartDVR Formula™ Surveillance Mode 34

Enable Windows Lock ③When SmartDVR Formula™ is running, Windows Lock disables certain Windows functions or shortcut keys. When the lock is on the following functions and shortcut keys will become unavailable.

Use Overlay function④Use the overlay function of the video card. Use the overlay function to remove incidental images. Note Overlay function may not work properly with some video cards. Disable the overlay function in such a case. Windows functions/Shortcut keys When lock is on Desk top Hide Start button Hide Task bar Hide System watch Hide Alt+Tab Disable Task Switching Keys(Alt +Tab) Disable Task Manager Disable Ctrl+Alt+Del Disable Ctrl+Shift+Esc Disable SmartDVR Formula™ Surveillance Mode 35

Exit Setup ⑤When exiting SmartDVR Formula™, it can be configured to close SmartDVR Formula™ program only, or shut down or reboot the DVR system.

Audio Setup ⑥Set the gain of audio input. AUD1 ~ AUD8 controls the gain for the audio channel supported by the DVR Board or Digital Audio Board. Set the gain to minimum (0) when using amplified microphones. (E.g.: model with built-in amplifier circuit) Sound Card controls the sound card volume for the audio input.

Video / Audio Setup ⑦Input Camera Type Setup NTSC: Korea, USA, Japan, Australia (some region), North America (some region), etcPAL: Other regions excluding NTSC regions (China, Europe, South America, etc.) Channel Selection Select the channel to monitor. Turn off the channels that do not have any camera connections.Video Resolution Setup Select the recording resolution for video images. Choose either low resolution mode or high resolution mode. Ref NTSC – 320X240, 640X480 / PAL – 360X288, 720X576SmartDVR Formula™ Surveillance Mode 36 Channel Configuration

Channel Caption Input ①Insert the description of the area that is under camera surveillance.

Caption Setup ②Surveillance Mode Configure whether to show the channel number and description of the surveillance area on the video images in the main program.Search Mode Configure whether to show the channel number and recording time on the video images in the search program.

Caption Font and Color Setup③Choose desired fonts and colors for the captions for the channel number, camera surveillance area, and recorded time, etc. SmartDVR Formula™ Surveillance Mode 37

Video Source④You can setup brightness, contrast, hue, saturation and sharpness to optimize video quality. Store Configuration

Store Disk ①Displays hard disk drives installed on the system. (Removable disks not included.) (Check(√) the hard disk drive to be used for storage.) Note If the surveillance images are being stored in a disk drive which has an operating system installed, the system may stop or repeat rebooting when the disk drive is full.

Disk Information ②Displays information about the disk drive that was selected from the list of storage devices SmartDVR Formula™ Surveillance Mode 38 .

Overwrite ③The oldest image data will be erased and new image data will be recorded when free disk space is less than the minimum free disk space (Default: 1024 MB). Notice You can use the HDD with disk space shortage errors with the overwrite function enabled. However this means that the oldest data will be automatically erased. Therefore it is recommended to backup important data in advance by using the Backup Manager.

Recording Quality and Recording Frame Rate setup ④Maximum recording frame rate and image quality can be configured for each channel. Ref File sizes for a single frame for different image qualities and resolutions are shown in the table below.

Watermark ⑤

Image tampering can be prevented by inserting a watermark in every frame.Normal: A watermark by the form of ‘DVR’ will be inserted.User Define Mark: User-defined watermark will be inserted. You can design your own mark. Image Quality Resolution File Size/frame(KB) Low Low Resolution 2.5 KB Low High Resolution 6.0 KB Medium Low Resolution 3.7 KB Medium High Resolution 10.0 KB High Low Resolution 5.0 KB High High Resolution 15.0KB SmartDVR Formula™ Surveillance Mode 39 Network Configuration

Server function setup ①Enable TCP/IP server This enables the system to act as a server for remote surveillance via internet connection. Remote surveillance using the Client Program or a web browser is possible once you are connected to the internet. Enable the Modem Server This enables the system to act as a server for remote surveillance via PSTN network. (general modems that use telephone lines) If a modem is installed on the system, connect to a PSTN network and access the remote surveillance through the Client Program. Remote surveillance by a web browser is not supported. SmartDVR Formula™ Surveillance Mode 40 Use Duplex(Two-Way) Audio This enables voice communication between the DVR Server and a NetClient user. (Refer to page 69 and 106 for application)

Network Information ②You can check the system IP address & MAC address. Ref If the DVR system IP address changes frequently or every time the DVR system reboots, it is likely that the DVR system is using a dynamic IP. If you wish to connect to a DVR system that uses a dynamic IP for remote surveillance, we recommend using the DHS service run by our company. DHS : Dynamic Host Services.

User Limit ③Network connection port You can change the connection port for remote surveillance function. (Default: 20408 port). Maximum. Connection No Specify the maximum number of remote surveillance users that can be connected to the DVR system at once.

Max Network FPS Specify the limit on the number of frames per second transferred on the network.

IP Manager Setup ④Remote surveillance connections from specific IP addresses can be authorized or prohibited. Disable : Allow access from any IP address. White IP: Authorize access from certain IP addresses. Black IP: Prohibit access from certain IP addresses.

Dynamic IP ID authentication & registration ⑤User of Sharing IP Use this option when using an internet router for internet connection, and for the connection to the DVR system. Register DHS service: Insert the ID you have registered to our DHS Service and receive authentication. (refer to page 66) SmartDVR Formula™ Surveillance Mode 41 Schedule Configuration

Schedule Chart ①You can set schedules for each channel using the left mouse button to click or drag. Schedule type (see ) must be selected ③first. You can remove schedules by using the right mouse button to click or drag. Clear: All schedules for the current channel will be cleared. Apply All: The schedule setup of the current channel will be applied to all channels.

Set Schedule Function ②Schedule will be enabled only when the box is checked.

Schedule Type ③After selecting one of the 4 schedule types, use your mouse to set schedules. SmartDVR Formula™ Surveillance Mode 42 Recording schedule: High-lighted in red. Recording lasts through the specified time. Motion detection schedule: High-lighted in green. If motion is detected during the specified time, the surveillance images are recorded. Sensor schedule: High-lighted in blue. If there is a sensor input during the specified time, the surveillance images are recorded. Dial-up schedule: High-lighted in orange. If motion is detected during the specified time, the DVR system makes a phone call to a pre-designated phone number. Maintenance Configuration

Windows Info ①Displays Windows and system information of the DVR System.

DVR Version Info ②Displays the version and board type of the DVR System. SmartDVR Formula™ Surveillance Mode 43

DVR System ③Displays the version and size of SmartDVR Formula™ components.

System Maintain ④This is a function which checks the DVR System & video data files for any errors when starting SmartDVR Formula™. Normal Check Mode: Only checks the recorded data for a single day. Full Check Mode: Checks all recorded data.

System Auto Reboot ⑤Setup to reboot the DVR System regularly. This is recommended for stable Windows operation and data verification.

System Log- Runs the system log viewer.SmartDVR Formula™ Surveillance Mode ⑥44 Event Recording Setup

Sensor ①Check the box to enable use of sensors. Click each channel to activate the installed sensor. You can select one of two sensor types. Ref Sensor Types NO (Normally Open) NO type sensors are normally open. The sensors close when something has been detected. No additional setup is required for NO types. NC (Normally Closed) NC type sensors are normally closed. The sensors open when something has been detected. You need to activate the NC mode by clicking the [NC] button below each sensor number. SmartDVR Formula™ Surveillance Mode 45

Action / Digital Output ②You can select which action the DVR system will take when a sensor has been triggered. Enable the Event Recording The DVR will start recording the corresponding channel when a sensor has been triggered. Recording will continue for a duration specified by the user (See Duration). ⑤Enable the Warning Sound A pre-designated wave file will run for a duration specified by the user (see Duration). ⑤For selecting the wave file, see Warning sound.④Send E-mail at Detection A still image taken at the time of the detection will be sent to an email address. Enter the e-mail address in [Configuration] →

[E-mail/Dial-up] (See pages 53-54). Enable Channel Pop-up Displays an enlarged screen of the corresponding channel when a sensor has been triggered

Enable the Digital Output ③Various output devices (warning light, siren, warning speaker, etc.) will be activated when a sensor has been triggered. Select the channels for the digital output. Also select NC/NO type for each channel.

Warning Sound ④Choose a warning sound which will be activated when a sensor is triggered. Click [Find] to search for a wave file.

Duration ⑤Specify the duration for which the warning sound or recording will last. For example if you choose 10 sec, the DVR will record and make a warning sound for 10 sec.

Motion Detection ⑥When motion is detected in a particular region of the screen, the DVR system may start recording or send a still image by e-mail. This function is done by analyzing surveillance images and does not require an external sensor other than the camera. SmartDVR Formula™ Surveillance Mode 46 Detection Area Setup Click and drag with your mouse to draw a box to specify the area of the screen where you want to detect motion.Detection Area Setup You can setup the area you wish to detect motion by using mouse drag on preview image.Set Motion When motion is detected, the region of the screen where the motion has been detected will be indicated by a blue box. Motion Recording Images will be recorded when motion is detected. Draw Small MD Box Displays small green boxes that follow the motion. Pop-Up at MD Displays an enlarged pop-up screen of the channel in which motion has been detected. Lasts for a duration specified by the user (See pop-up time). ⑧Send E-mail at MD A still image taken at the time of the detection will be sent to an email address. Enter the e-mail address in [Configuration] → [E-mail/Dial-up] (See pages 53-54). Enable the Dial-up When motion is detected, the program makes a phone call to a

phone number specified in [Configuration>e-mail/dial-up]. Refer to the section on [E-mail/dial-up] for detailed information (pages 53-54)

Sensitivity setup ⑦You can adjust the sensitivity level of the motion detection. Increase the sensitivity to detect small motions. Decrease the sensitivity to avoid detecting small, less significant motions.

Duration Time ⑧You can adjust the duration of the [Pop-up at MD] function. SmartDVR Formula™ Surveillance Mode 47 Receiver Configuration

Receiver Channel Setting ①Setup the P/T/Z camera or receiver address for each video channel. Ref Most P/T/Z cameras on the market have camera addresses. Camera addresses can be configured by using the OSD menu or the deep switch inside the camera. The P/T/Z functions will not work if the address you entered and the camera address do not match. Make sure they are the same. Selected Serial Port: Select the serial port where a P/T/Z camera or receiver will be connected.

Device Spec ②Specifications of the device selected from [Device Type] screen on the right is displayed here. Specification includes the manufacturer, model, baud rate, byte size, parity bit, and stop bit. SmartDVR Formula™ Surveillance Mode 48

Device Type ③Select a P/T/Z camera or receiver protocol with your mouse. Only one protocol should be used even if there are more than one kind of P/T/Z camera or receiver.

Extend Function ④Swap vertical command (Up/Down) Invert the vertical control command transmitted to the P/T/Z camera. Swap horizontal command (Left/Right) Invert the horizontal control command transmitted to the P/T/Z camera.Preset Configuration

Single Mode ①You can select the video channel which is connected to a camera that supports presets. Presets can be configured differently for each channel. SmartDVR Formula™ Surveillance Mode 49

Scenario List ②You can compose the configured presets into one flow chart. When a scenario starts running (See Scenario RUN and ⑤PAUSE.), it will run in the order of the presets in the scenario list.

Preset Setting ③Scenario No- Displays the number of the Scenario you have selected. Preset No- Displays the number of the preset selected for adding or modifying. Delay Time Configure for how long the current preset location will be held.Control Panel Configure the current preset location using the P/T/Z buttons. Add Add the current location to the preset being edited, and apply it to the scenario list at the same time. Modify Current preset location and delay time will be modified to the new values that you have entered. Delete The selected preset from the scenario list will be deleted. However, the camera location saved in the preset camera will not be deleted.

Reverse Scan ④Once the scenario list has proceeded to the last preset, it will start scanning back in reverse and keep cycling in this manner. Example) Preset 1 Æ Preset 2 Æ Preset 3 Æ Preset 4 Æ Preset 3 Æ Preset 2 …

Scenario RUN and PAUSE ⑤Scenario RUN: Scenario list will be run from the top preset and move down to the preset on the bottom. Click again to stop the scenario. PAUSE: Click to pause a running scenario.SmartDVR Formula™ Surveillance Mode 50 Video Out Configuration You can the use video output with an additional analog monitor. Note This function has no relation to the switching display function in [Configuration] → [General].

Enable the TV Out Rotation ①You can configure the images to automatically change channels in sequence when an analog monitor (CCTV Monitor) is connected to the DVR system.

Single Mode ②You can select one specific channel to view if you do not wish to view different channels in sequence on your analog monitor.

Rotation Mode Time Gap ③

When you use automatic display sequence function by enabling TV Out Rotation, you can adjust how long it will stay on one channel before changing to the next channel. SmartDVR Formula™ Surveillance Mode 51

Rotation Mode Channel ④Select which channels you want to view in sequence. For example if you select channels 1, 5, 7, and 8, only those channels will be displayed in sequence on the analog monitor. E-mail Function Configuration

Mail server ①Enter the address of the SMTP server that you are going to send the e-mail from. Note The server must be a SMTP server for the e-mail to be sent properly. Example) smpt.mail.yahoo.co.kr

Sender ②Enter information about who is sending the e-mail. The e-mail address must be same as the [SMPT server] of . ①Example) Mail server: smtp.mail.yahoo.oc.kr E-mail address: xxx@yahoo.co.krSmartDVR Formula™ Surveillance Mode 52

Message Recipients ③To - Enter the e-mail address of the recipient. Cc – Enter the e-mail addresses of other recipients. Bcc – Enter the e-mail addresses for blind carbon copy. The e-mail addresses entered in the [Bcc] field will not be shown to any of the other e-mail recipients including the ones in [To] and [Cc] field.

Log on information ④User name Enter the ID that is used in e-mail server. Password Enter the password that is used to log on the server. Test Account Click to send a test e-mail to see if the e-mails will be sent successfully with the information that has been entered. Even if the e-mails seem to have been sent successfully, we recommend checking the received e-mails for confirmation.

E-mail timer Setting ⑤Adjust the interval (in seconds) of sending the e-mails. Dial-up Phone number Input the telephone number of the receiver. Dial-up Interval Adjust the interval (in minutes) of the phone call to be made when an event has occurred (motion detection).

Use outside line Configure whether to use outside line or not, and enter the outside line number to use. SmartDVR Formula™ Surveillance Mode 53 User Management configuration

User List ①Displays a list of currently stored user accounts. To create an account, select an empty account named [Not used]. To modify or delete an account, select an account, and modify or delete it.

User information ②Displays selected user's account name, password etc. User information renewal: Click to apply any account changes including newly created accounts. Account delete: Delete the selected account.

Accessible local function ③Configure authorizations of user access to the DVR local functions. When a user logs on to the system with a user account, only the checked functions will be available.SmartDVR Formula™ Surveillance Mode 54

Accessible Network function ④Grant authorizations to users connected to the system from a remote location using NetClient or WebClient. You can allow authorizations for surveillance mode and search mode separately.

Accessible channel ⑤Establish access authorizations for user accounts. Granting access to SmartDVR Formula™ search function is not a part of this configuration, so we recommend that you deny search access to users who have been denied channel access. Note Display Setting in RD(Real Display) boards Right-click on the surveillance display in a DVR board with RD board installed. Open the Display Setting window to change any display settings. Note This setting only affects the video that is displayed in surveillance mode. To change settings about the actually stored images, go to [Configuration] → [Channel]. Auto Gain Control: Controls the gain of the input video signal automatically. Gain Control: When [Enable Auto Gain Control] is not checked, users can directly control the gain. Edge Control: It controls the sharpness of the images to make the edges of images more clear. Checking

[Enable Edge Control] will make images sharper, but will also create more noise. Display Color Setting: Adjusts the brightness, contrast, and saturation of the images. SmartDVR Formula™ Surveillance Mode 55

Management Log-in / out⑥Configure the auto log-in and log-out function Enable Logging-out By Timer. If specified the duration is exceeded, the program is logs out automatically. In [Timer Options] you can either choose to log out or just change the user. Log-in automatically at starting When SmartDVR Formula™ starts, it will automatically be logged in with a pre-designated account. If this function is disabled, program will start in a logged out state. SmartDVR Formula™ Surveillance Mode 56 Application use Camera Types and Configuring Resolutions When SmartDVR Formula™ S/W is installed, only one channel is activated. So you must configure it to your system environment. Click [Configuration>General].

Video Auto Setting ⑥NTSC: Korea, USA, Japan, Australia (some region), North America (some region), etc. PAL: Regions outside of NTSC regions(China, Europe, South America etc.).

Activate the channel with a camera ②connected. Ref Disable channels that are not connected to cameras.

Select a resolution for each channel. ③You can either select the high resolution mode (NTSC: 640x480 , PAL 720x576)or the low resolution mode. (NTSC: 320x240, PAL: 360x288 ) High resolution mode has a good picture quality, but takes up more disk space. Low resolution mode provides average picture quality but requires less disk space. Image picture quality configuration User can configure the picture quality of the

image of each channel according to user’s environment. Go to [Configuration] →[Channel] Select the channel and adjust the picture quality for that channel in [Video Source] on the bottom right side of the screen. SmartDVR Formula™ Surveillance Mode 57 Audio Configuration When SmartDVR Formula™ S/W is installed, all audio are inactive. Therefore, in order to use audio, you must configure the audio setting for each channel. Assign an audio channel for each video channel Click [Configuration>General]

Assign an audio channel to a video ①channel with a camera installed close to the audio channel input device. One audio channel can only be assigned to one video channel. Audio input control Click [Configuration>General]. Adjust the audio gain levels to be suitable to the actual environment. Generally, for microphones with built-in amplification circuits, adjust the gain level to zero.Motion Detection Configuration This function detects motion in areas specified by the user. Setting the detection area to someplace with little average motion will allow more recording time. Click [Configuration>Event]. Another way to configure motion detection is right-clicking on a channel in the main surveillance screen, and clicking [Channel Setting]. SmartDVR Formula™ Surveillance Mode 58

Click and drag with your ①mouse on the preview screen to designate the area to watch for motion.

Click [Set Motion] to ②activate the motion detection function. Motion detection will not work unless you activate the [Set Motion] button.

Configure the actions to ③take when motion is

detected. Set Motion When motion is detected, the region of the screen where the motion has been detected will be indicated by a blue box. Motion Recording Images will be recorded when motion is detected. Draw Small MD Box Displays small green boxes that trace the motion. Pop-Up at MD Displays an enlarged pop-up screen of the channel in which motion has been detected. Lasts for a duration specified by the user (See pop-up time). ⑧Send E-mail at MD A still image taken at the time of the detection will be sent to an email address. Enter the e-mail address in [Configuration] → [E-mail/Dial-up] (See pages 53-54).

You can adjust the sensitivity level of the motion detection. ④Increase the sensitivity to detect small motions. Decrease the sensitivity to avoid detecting small, less significant motions.

You can adjust the duration of the [Pop-up at MD] function SmartDVR Formula™ ⑤Surveillance Mode 59 Sensor and digital output Configuration Configure sensors and digital outputs connected to the DVR system. The DVR system supports a maximum of 16 sensors and 16 digital outputs. (I/O boards required) Connect a sensor or a digital output device (alarm, light, warning sound, etc.) to a camera channel for an intertwined operation. Sensor establishment

Go to [Configuration>Event]. ① Select a video channel that ②

has a sensor installed nearby

Check [Enable the Sensor(s)]. ③ Select the port number ④

that the sensor is connected to. Note It is not the port number of the camera, but of the sensor. Refer to Sensor/Digital Output Setup on page 10 for getting information on the channel that the sensor is connected to.

Sensor Types. ⑤NO (Normally Open)

NO type sensors are normally open. The sensors close (shortcircuit) when something has been detected. No additional setup is required for NO types. NC (Normally Closed) NC type sensors are normally closed. The sensors open when something has been detected. You need to activate the NC mode by clicking the [NC] button below each sensor number.

Sensor setup is complete. SmartDVR Formula™ Surveillance Mode ⑥60 Digital output Configuration

Go to [Configuration>Event]. ① Check [Enable the digital output(s)]. ② Select the port number ③

that the digital output device is connected to. Note It is not the port number of the camera, but of the digital output device. Refer to Sensor/Digital Output Setup on page 10 for getting information on the channel that the digital output device is connected to.

Configure the type of the digital output devices. ④NO (Normally Open) NO type digital output devices are normally open. The digital output devices close (short-circuited) when something has been detected. No additional setup is required for NO types. NC (Normally Closed) NC type digital output devices are normally closed. The digital output devices open when something has been detected. You need to activate the NC mode by clicking the [NC] button below each sensor number.

Digital output device setup is complete. SmartDVR Formula™ Surveillance Mode ⑤61 E-mail setup If use together E-mail and motion watch or sensor watch, can receive still image of relevant channel by E-mail in case of motion or sensor is.

Input mail server address of side of sender. ①E.g. www.yahoo.co.kr / smtp.intotech.co.kr

Input information of side of ②sending mail. Only, E-mail site that is recorded to E-mail address should be equal with 's [mail ①server]. E.g.

E-mail server:smtp.intotech.co.kr / Email: indiwe@intotech.co.kr

Input email address of recipient ③TO: E-mail address of recipient CC: input E-mail address of other recipients BCC: input E-mail address for Blind

Setup E-mail response time after sensor has been triggered. ④Ref E- Mail function does not support mailing. Therefore, encourage test certainly after establish E- mail function. If set time so shortly in case of watching continuous motion, too many mails can be transferred to a recipients. Also, encourage that setup to channel that can get action less and clean image if is possible. SmartDVR Formula™ Surveillance Mode 62 User account Configuration SmartDVR Formula™ can create up to 30 different accounts. Different authorization levels can be granted to each account. Go to [Configuration>User Management].

Select an empty account by clicking [Not Used]. ① Under [User Information], ②

enter the ID and password. Repeat the password in [Confirm].

Click [Modify user ③information] button to apply changes and create a new account.

[Accessible local ④function] allows you to configure authorization to DVR functions. The same authorization level applies when the user is connected from a remote location.

Under [Accessible ⑤Network Functions] you can configure authorization levels for monitoring and searching when connected via network.

Under [Accessible ⑥Channels] configure which channels the user is going to have access

to. The same authorization level applies for both when you are logged on directly or via network. SmartDVR Formula™ Surveillance Mode 63 Receiver Configuration [Receiver] options must be configured when P/T/Z cameras are connected to the system. Go to [Configuration>Receiver]

Select a channel that has a P/T/Z camera connected. ① Configure the address of the P/T/Z camera. Generally, camera ②

addresses have values between 0 to 255. The way to configure addresses for different camera models may vary, therefore consult the manufacturer or refer to the manual of the camera that you are using.

Select the serial port that the P/T/Z camera is connected to.③ Select a protocol for the P/T/Z camera. ④ In case of using inverted control for right/left, and up/down ⑤

movements of the P/T/Z camera, check the corresponding options . Click [Apply] to save the configurations.⑥ When configuring more P/T/Z cameras connected to other channels, ⑦

repeat steps to . SmartDVR Formula™ Surveillance Mode ① ⑤64 Preset Configuration You can use preset functions when a camera that supports preset functions is connected. Camera automatically follows a path along several pre-specified locations. Note Not all P/T/Z cameras support preset functions. Refer to the camera manual or manufacturer about the availability of preset functions. Go to [Configuration>Preset]

Select the channel on which you wish to ①setup a scenario.

Select a preset number to which you will ②be saving the current camera position.

Setup the camera position using P/T/Z ③buttons in the [Control Panel].

Click [Add] to add the current preset to ④the [Scenario List] shown on the left. Use [Modify] and [Delete] to modify or delete a preset.

Check the [Scenario List] to make ⑤sure everything has been configured properly and click [Scenario RUN]. When you click on a preset in the

[Scenario List], the camera moves to the preset position and it will be displayed on the preview screen.

Up to 32 presets can be added by ⑥repeating the above steps.SmartDVR Formula™ Surveillance Mode 65 Network Configuration It is service that can see image in remote place using specification ID without necessity to make sure IP changed continuously in DVR System which linked in dynamic IP. Move to [configuration> network]. Make sure whether was checked to [TCP/IP server use] or not. Please check if was not checked.

Input ID that subscribed for ①DHS service and clicks [register Dynamic IP User ID] button. Log in & Log out Function Use log in & out function to prevent access to configurations and main functions by anyone other than the administrator and authorized users. Log in

The red lock indicates logged out status ① When you click the button, the login windows will ②

appear. After log in, the button is changed into a black open ③

lock. SmartDVR Formula™ Surveillance Mode 66 Log out When you click the black, open lock button, the following dialog will appear. Click “Yes” to log out. DHS service setup When your DVR system is connected to a dynamic IP address, use DHS Service to monitor images via a remote connection, without having to frequently check for new IP addresses. Note Coupons for using DHS Service are sold separately. For more detailed information, please visit our website http://www.intotech.co.krGo to [Configuration>Network].

Confirm if [Enable the Network ①Server] is checked. If not, check it.

Register in ②http://mybangsong.com/O_dhs.

Click [Register]. ③ After inserting ID, click [Registration]. SmartDVR Formula™ Surveillance Mode ④

67 Duplex (Two-Way) Audio Function This enables communication between the DVR Server and NetClient. Go to [Configuration>Network].

Check [Use Duplex Audio]① In the main screen, Click ②

the [Network Info Button], and ‘Network Information window’ will appear as shown in the figure below.

Information such as the ID and IP address of the Two-Way Audio ③user will appear in [Client Information].

Use the slide bars to control the volume of speakers and ④microphones. SmartDVR Formula™ Surveillance Mode 68 Client Connection

When a client has connected, a notification window will appear. ① You can see the user information in the Network Information ②

screen. Client Disconnection When a client disconnects, a window will appear to notify you. SmartDVR Formula™ Search Mode 69 SmartDVR Formula™ Search Mode SmartDVR Formula™ Search Mode allows users to search and play the recorded images and audio by time and date. The search mode supports saving an image to a .bmp file, printing the image, and checking the watermark on the .bmp file. □1 Control Panel □2 Playback Control Panel □3 Screen Partition Panel □4 Data Search Process Panel □5 Audio Volume Control Panel SmartDVR Formula™ Search Mode 70 □1 Control Panel You can use the control panel to switch to surveillance mode, search for data, and do various backup functions.Surveillance Mode: Switch to surveillance mode. Date Search: Opens up a calendar that can be used to search for dates on which video was recorded. Save Button: Save a still image of the selected channel to a bmp file. Print Button: Print the image of the selected channel. Watermark Viewer: Run WaterMark Viewer to view watermark of recorded original image.

AVI Backup Manager Switch: Switch to AVI Backup Manager Mode where you can backup the video to a AVI file. Refer to page 83 for a more detailed operation. Backup Manager Switch: Switch to Backup Manager Mode where you can backup important data to a hard disk drive or a CD. Refer to page 87 for a more detailed operation. SmartDVR Formula™ Search Mode 71 □2 Playback Control Panel Playback: Playback at normal speed Pause: Pause Reverse Playback: Play backwards 2x Playback: Playback at 2x. 4x Playback: Playback at 4x 2x Reverse Playback: Playback in reverse at 2x. Play Next frame: Playback frame by frame Previous frame Reverse: Playback in reverse frame by frame Only supported in 4 channel or 1 channel viewing mode. □3 Screen Partition Panel Support 8 different screen partition modes. □4 Data Search Process Bar Hour Select Button: Hours in red indicate that data was recorded in that hour. Hour: The hour currently being searched is displayed in the long, grey rectangle SmartDVR Formula™ Search Mode 72 Daily Search Bar: Recorded data is indicated in red. You can see in more detail when something was recorded. Daily search (0h:0m~23h:59m) Search point indication icon Click and drag the search point icon on the search bar to quickly search through a vast amount of data. Data Search by Channel Display what mode the data was recorded in: normal, motion detection or schedule mode. Ref To use the function, right-click anywhere on the Data Search Process Bar. A search scroll bar will appear as below. Click the [x] on the top left corner to close. Ref Red: Data recorded in normal mode. Green: Data recorded in motion detection mode. Yellow: Data recorded in schedule mode □5 Audio Volume Control Panel Control the audio volume when playing recorded data. When audio was recorded in more than one channel, you will only hear the audio from the selected channel. SmartDVR Formula™ Search Mode

73 Calendar In [SmartDVR Formula™ Search] screen, click [Load Data] to open the calendar. Red: Dates that have recorded dataBlue: Current selected date.Grey: No recorded data MD ONLY: Load only the data recorded in motion detection mode. LOAD Button: Load all recorded data in the selected date. SmartDVR Formula™ Search Mode 74 Smart Search Mode In Smart Search Mode, you can make searching through recorded data easier by selecting an area and letting the program search for any motion in that area.

Load the recorded video data and click the play ①button as shown on the figure to the right.

In order to run Smart Search, pause the playback. ② Right-click on the channel that you wish to run ③

Smart Search on. Then click [Enable Smart Search]. SmartDVR Formula™ Search Mode 75

Smart Search screen will appear as the figure below. ④ Designate the area of the screen in which you wish to search for ⑤

motion. Green rectangular boxes will appear. (Left-click: Set search area / Right-click: Cancel search area) SmartDVR Formula™ Search Mode 76

Configure the time you wish to search, and the sensitivity of the ⑥motion detection. (Place the mouse cursor on the specific time at which you wish to start the search, and click [Start File]. Place the cursor on the specific time you wish to end the search and click [End File].

Click [Start Search] to start the search. ⑦ After the search begins, the detected motion and the corresponding ⑧

time will be listed in order. SmartDVR Formula™ Search Mode 77

When you wish to play the video acquired by the search, first, click ⑨[Stop Search]. Then on the list, double-click the time that you wish to start playing, and a message will appear

Click [Yes] and the video data will be played. ⑩ When all the search is complete, click [Expand] to switch to the ⑪

main search screen. In the main search screen, you can use additional functions such as fast-forward, re-wind, frame-by-frame playback, image save, image print, etc. SmartDVR Formula™ Search Mode 78 Printing the Current Image

Click [Print] in the SmartDVR Formula™ Search screen. Print Channel: Select the channel you wish to print. Option: Choose whether to print the images with caption. Also select printer setup. The channel number and the recorded time will be included in the caption. The recording location will not be included. Print Type: Configure print layout. Watermark Viewer Icon You can open the saved bmp file to determine if there has been any image tampering by checking if the watermark on the bmp file is identical with the original image. Ref Watermarks can prevent illegal-copying and protect the license and ownership of data owner. The digital watermarking function does not affect the image viewing or using the program in any way. The watermark is very useful for finding the source of the original copy and the reprinting route. SmartDVR Formula™ Search Mode 79

Click [WaterMark Viewer] in SmartDVR Formula™ Search screen ①to open the watermark viewer.

Click [File>Open] and load the images stored in the DVR System. ②Ref (Images must be in bmp format)

Click [WM Detect] to check if the image has been tampered. ③If an image has been tampered, an “X” will be displayed in [User Defined Mark] as shown below. SmartDVR Formula™ Search Mode 80 Digital Zoom function Digital Zoom function allows you zoom in on a part of the image being played in SmartDVR Formula™ Search.

Click a channel to select it. ① Use your mouse wheel to zoom in and out. You can zoom in ②

up to 4x.SmartDVR Formula™ AVI Backup Manager Mode 81 SmartDVR Formula™ AVI Backup Manager Mode AVI Backup Manager converts the recorded data into AVI file format, so you can view the recorded images conveniently by using any media player available. e.g. Windows Media Player. Click [AVI Backup Manager] in SmartDVR Formula™ Search Mode or your Windows desktop. □1 Playback Control Panel □2 Channel Panel □3 AVI Convert Control Panel □4 Audio Volume Control Panel □5 Data Search Process Panel SmartDVR Formula™ AVI Backup Manager Mode 82 □1 Playback Control Panel Playback: Playback at normal speed Pause: Pause

Reverse Playback: Playback reversely 2x Playback: Playback at 2x speed. 4x Playback: Playback at 4x speed 2x Reverse Playback: Playback in reverse at 2x speed. Play Next frame: Playback frame by frame Previous frame Reverse: Playback in reverse frame by frame Only supported in 4 channel or 1 channel viewing mode. □2 Channel Panel Select the channel that you wish to convert into an AVI File by clicking it. Click again to cancel the selection. SmartDVR Formula™ AVI Backup Manager Mode 83 □3 AVI Convert Control Panel Selected channel data is converted into an AVI File. Backup time setup: Choose what part of the recorded data to backup by clicking [A→B] once to set the start time, and clicking [A→B] again to set the end time. Convert into AVI File: Click to start AVI File backup. □4 Audio Volume Control PanelControl the audio volume during a playback of recorded data. If various channels have been recorded, then you will only hear the audio from the selected channel. □5 Data Search Process Panel Hour Button: Hours that have recorded data are indicated in red. Minute Bar: Displays the data of the selected hour in minutes(0 to 59 min). Recorded data is indicated in red. Search Mark Icon: Points to the current time position on the recorded data. Time: Shows the current time position on the recorded data. SmartDVR Formula™ AVI Backup Manager Mode 84 Application Click [AVI Backup Manager] in SmartDVR Formula™ Search screen or start AVI Backup Manager from your desktop.

Click [Load Data] to bring up the calendar. ① Select a day with the recorded data that you wish ②

to back up, and click [LOAD]. Select the channel you wish to back up in Channel ③

icon. Channel icons turn green when selected. On the time bar, enter the time at which you wish to ④

start the backup. You can only choose from the red regions. (Red means there is data recorded at that time.).

Click a position on the time bar and click [AÆB] ⑤to set a start time. The exact time will automatically appear.

Click another position on the time bar and click [A⑥→B] to set an end time. Then exact end time will

automatically appear. Click [Converting]. ⑦

Select a directory to store the backup data. Click [OK] to start the backup process. A message window will appear to prompt that the conversion was successful. See the figure on the right. Ref Up to one hour of recorded data can be converted to a single AVI file. When the recorded data being backed up is less than an hour long, the back up data length will be indicated. SmartDVR Formula™ AVI Backup Manager Mode 85 Playing Backup Data using Windows Media-Player The AVI files that have been backed up by AVI Backup Manager use INTOTECH’s own codec. There for, to play the backup AVI file in a computer without the DVR software installed, INTOTECH’s codec must be installed first. INTOTECH’s Codec can be downloaded for free at (http://www.intotech.co.kr) and it can also be found in the installation CD. Note Installing other codecs when INTOTECH’s codec is already installed may cause playback problems. To avoid such problems, install INTOTECH’s codec after installing all other codecs.

Go to the location where you saved the AVI file and open it. ① Windows Media Player will play the AVI file. SmartDVR Formula™ Backup ②

Manager 86 SmartDVR Formula™ Backup Manager Mode SmartDVR Formula™ will help you easily back up recorded image data onto a hard disk or a CD. Note CD backup function is only supported in Windows XP or higher □1 Data List □2 Control Panel □3 Backup List □4 Backup and Progress SmartDVR Formula™ Backup Manager 87 □1 Data List Images recorded in the DVR system are displayed in the order of [Stored Location >Recorded Date>Recorded Channel>Recorded Time]. Items which has + mark on their left have sub items. Click to view the sub-items. Click to select the image data to backup. □2 Control Panel This is the control panel for backup. You can select the image data to

back up. Add : Adds the selected image data from the ①

data list to the backup list. Delete : Removes the image data from the ②

backup list. Delete All : Deletes all the image data from the ③

backup list. Avi Backup Manager : Run the AVI Backup ④

Manager. Player : Runs [SmartDVR Formula™ Search]. ⑤ Start Backup : Starts backing up the data in ⑥

the backup list to the backup folder.

Stop Backup : Stops ⑦backup.

Start CD Backup : Backs up to a CD. If the volume is larger ⑧than the whole disk space of one CD, then it will be divided and backed up to multiple CDs. Select by Range Select data to add to the backup list by time. Select start time & end time and select the channel to add to the list. Click [Add] to add the relevant files to the backup list. The files that lie in the boundary of the start time & end time is added to backup list together.SmartDVR Formula™ Backup Manager 88 □3 Backup List The backup list shows the data files to back up. An data file named in the following format. Familiarizing yourself with the name format will be helpful when adding files to or deleting files from the backup list. 00 - 200501281533-0000.IVA Channel Year/Month/Day/Hour/Minute File No. Ref Channel number ranges from 00 to 15 □4 Status Select backup folder : Select a location to save the backup files to. You can select a location in a hard disk drive or a removable disk(e.g. flash memory). Folder : The folder to save the backup files. Backup Progress : Displays the back up progress. SmartDVR Formula™ Backup Manager 89 Application Use Use Backup Manager for HDD backup Click [Backup Manager] in SmartDVR Formula™ Search screen, or click [Backup Manager] icon from your Windows desktop.

Select time of the channel for backup from Data List. ①

E.g. Image recorded in channel 1 on 15:00 hour 2005. 01. 28. Click [Add >>] button to register ②

selected image on Backup List. Confirm Backup size and click [Select ③

Backup Folder] button to configure backup folder.

Click [Start Backup] button to start ④backup. Ref Data which has been backup on the DVR System cannot be overwritten so it will take a certain amount of volume. Therefore, the recording period of DVR system may become shorter. Use Backup Manager for HDD backup 2 Select range and select start time and end time. Select channel for backup. Multiple channels can be selected. Click [add] button and register the image of the selected range to backup list. Click [Start Backup] button and start backup. .SmartDVR Formula™ Backup Manager 90 Use Backup Manager for CD backup Click [Backup Manager] button from SmartDVR Formula™ search program, or click [Backup Manager] icon from windows main screen. Note CD backup function is only supported in Windows XP or higher.

Select the channel and the time to back up. ① E.g. Image Backup the image data ②

recorded from channel 1 at 15:00 hour on 2005. 01. 28. (yyyy.mm.dd)

Click [>>] to add the selected image ③data to the backup list.

Click [CD Backup] and the number of CD’s required will be ④displayed.

After CD backup begins, backup progress bar will appear. ⑤ When backup is complete, the CD will be ejected automatically. SmartDVR ⑥

Formula™ NetClient Mode 91 SmartDVR Formula™ NetClient Mode SmartDVR Formula™ NetClient can receive images from the DVR Server through the internet or a modem. You can monitor and record images using NetClient. You can even move the cameras, and zoom in and out if P/T/Z cameras are installed. □1 Control Panel □2 Screen Partition Panel □3 P/T/Z Control Panel □4 Channel Type Selection Panel □5 Other Panel SmartDVR Formula™ NetClient Mode

92 □1 Control Panel Use the control panel to open the search program, connection setup, and remote connection setup, and record images transmitted from the server. Search: Runs the search program Connection Setup : Opens [Connecting & Configuration Management] used for internet access. If you are using a modem, it opens [Modem Connection] used for internet access. Remote Connection Setup:You can connect to the DVR system and configure the settings. Recording: Records selected channels. All: Selects all channels. □2 Screen Partition Panel You can choose from 7 different screen partitions. You can also choose full screen mode, and sequential rotation display mode. SmartDVR Formula™ NetClient Mode 93 □3 P/T/Z Control Panel When a P/T/Z camera is connected to the DVR Server, select the channel you wish to control, and click the control buttons in P/T/Z Control Panel to control the camera. Also, use the drag panel on the bottom to control the playback speed of the surveillance video. Ref Only users with broadband internet connection (LAN Mode) can use P/T/Z control. Modem users (Modem Mode) cannot use this feature. □4 Channel Type Selection Panel Click a channel in the camera selection panel to enlarge the view . □5 Other Panel Modem: Select [MODEM] when using a modem.LAN: Select [LAN] when you have high speed network connection via ADSL, VDSL, Cable, LAN, etc.Record Image: Save a still image from the surveillance video currently being played.Print: Print the image from the surveillance video. Connection Setup for LAN Users If there is an existing LAN connection on your PC, settings will automatically be configured. Click [LAN] from the NetClient main screen to connect from a remote site using LAN. SmartDVR Formula™ NetClient Mode

94 Connection Setup for Modem Users Click [MODEM] in NetClient main screen to connect from remote site using a modem. Click [Configuration] to open -[Modem Connect] window. When [Modem Connect] window has initialized, enter the telephone number of the DVR server (If you are using an extension, also enter the number for outside calls). Enter ‘w’ in front of the telephone number to add the waiting time while the line is being dialed. E.g. Enter (w0232851525), and your ID and Password, (ID & Password which is registered in [User Management] of the server program). Select a channel and click [Connect]. Ref You can only access one channel at a time when you are using a modem. To view a different channel, click [Disconnect] and connect to the other channel. Configuration When you click [Configuration], the model name of the modem you are using will appear. During the initial setup, the model name needs to be confirmed to complete the registration. Thereafter, this step will be bypassed. Click [Properties] to view General/Advanced default setup. Use default when using a modem. SmartDVR Formula™ NetClient Mode 95 Registering DVR System with Static IP Address If the DVR system has a static (fixed) IP address, you can connect to the DVR system directly.

Click [Configuration] in the NetClient main ①screen.

Click [Fixed IP] Tab.② Insert the server name and IP address. ③

You may choose any name for the server. The default port number to enter is [20408], unless it has been changed.

Enter the ID registered to the DVR system. ④For more information on account registration and management, refer to page 56.

Add the DVR System to the fixed IP list. ⑤

You will be able to see the registered DVR system on the list. SmartDVR Formula™ ⑥NetClient Mode 96 DVR System DHS Service Registration If the DVR system has a dynamic IP address, you have to use the DHS Service.

Click [Configuration] in NetClient main ①screen.

Click the [Dynamic IP] tab. ② Enter DHS ID and port number. ③

DHS ID is the account registered to the INTOTECH DHS Service. It is not related with the DVR System account. Port number should be [20408] by default, unless it has been changed..

Enter a log in account registered to the DVR system. ④ Add the DVR system to the fixed IP list. SmartDVR Formula™ NetClient Mode ⑤

97 Ref Summary of DHS Service All computers that are connected to the internet have their own addresses called IP addresses. When you send a letter, it is delivered to the recipient after being sorted by its address in the post office. In pretty much the same principle, computers are able to communicate through the IP addresses on the internet. SmartDVR Formula™ supports various network functions for searching and setting up configurations from a remote location. There is a slight complication due to the fact that the IP addresses change from time to time. Due to the shortage of IP addresses worldwide, most of the telecommunication companies use a procedure that shares the same IP addresses with a number of computers in the order of connection. Therefore it is highly probable that a computer’s IP address changes every time it connects to the internet. If the IP address changes, you will no longer have the address with which to connect to the DVR System. DHS Service lets you overcome this limitation of the current internet environment. A DVR system registered to the DHS Service will notify the INTOTECH DHS server of its current IP address every 10 minutes. Even though remote users may not know the IP address of the DVR system, they can connect to the DHS Service which will then redirect them to the DVR system they are trying to connect to. This powerful service provided by INTOTECH will allow you to use network functions from anywhere in the world regardless of the constantly changing IP addresses. SmartDVR Formula™ NetClient Mode 98 Connecting & configuration Management

Connection Management ①

Configure connection settings for each of the 16 channels. Connect ②

For each channel, select the DVR system to connect to, and click [Connect] to connect. [Server Name] shows all the DVR systems registered to the Fixed and Dynamic IP list.

All Connect ③Click to connect to all available channels.

Information ④Displays information about the selected DVR System.

Status of Connection⑤Displays the current connection status. SmartDVR Formula™ NetClient Mode 99 Management of groupGroup Connection enables you to connect to multiple DVR Systems with a single click of the mouse.

Group List ①List of registered groups.

Server List ②List of DVR systems registered to Fixed/ Dynamic IP lists.

Channel ③Displays channels that can be connected to in the DVR system selected from the server list. You may directly configure the channels to connect to.

Add Group.④Add the selected channels to the selected group. SmartDVR Formula™ NetClient Mode 100 Advanced

Store Disk ①Check (√) a hard disk drive to use as the storage device Note If you choose a disk drive with an OS installed, the system could become unstable when the it runs out of free disk space. We recommend removing the check on the disk with OS installed (drive C by default) and select other drives to be used as storage. (usually D or E, etc).

Overwrite ②Check [Use Overwrite] to allow the system to overwrite the oldest data when the free disk space is less than the minimum free disk space allowed. SmartDVR Formula™ NetClient Mode 101

Display Mode ③Dual Monitor: Check [Dual Display] when you are using a dual display with a graphic card that supports it. Use Overlay: Use the overlay function of the video card. Use the overlay function to remove incidental images. Note Overlay function may not work properly with some video

cards. Disable the overlay function in such a case. YUV/RGB: Select either YUV or RGB mode. YUB mode consumes less resources than RGB mode. If you do not see any images in YUV mode, update your graphic card driver. If the problem persists, check whether your graphic card supports YUV mode. SmartDVR Formula™ NetClient Mode 102 Transmission Mode

Image Quality ①Adjust the quality of the images transmitted from the DVR server. Higher settings mean better image quality, but may slow down the performance due to larger file sizes.

Transmit Mode ②Remote Mode: Use the remote mode when using NetClient from an external network. Frame rate is decreased to improve transmission speed. Local Mode: Use the local mode when using NetClient from an internal network. Images are displayed in full frame rate. SmartDVR Formula™ NetClient Mode 103 Application Record images in NetClient You can record the remote surveillance images in the computer on which NetClient is running.

Log on the DVR System you wish to monitor. ① Left-click the screen you wish to record and click ②

[REC] button to start recording. Record captured image in NetClientYou can save a still image as a JPEG file in the computer on which NetClient is running. WaterMark function is not supported.

Connect to the DVR system you wish to monitor. ① Click on the image you wish to save and click the [Save] ②

button. In [Record File] window, select the directory to save to, ③

and click the [Save] . Print out still images of the images under remote surveillance You can print out captured images under remote surveillance using a printer connected to the computer on which NetClient is running. You can print up to 8 channels at once.

Connect to the DVR system you wish to monitor.① Click the image you wish to print out and click the [Print] ②

button. Setup print out shape and channel, and click [Print]. SmartDVR Formula™ NetClient③

Mode 104 Duplex (Two way) Audio Function

This enables voice communication between the DVR Server and a NetClient user. Note Both sides of the NetClient user and the DVR server must have an input device(microphone) and an output device (speaker or headphone).

Connect to a server from the [Connect Management] screen in ①NetClient. SmartDVR Formula™ NetClient Mode 105

Select a connected channel, right-click and open [Voice Chat].② If [Voice Chat] dialogue appear, select the server you wish to ③

connect to. (The current connected channel will be selected as default) SmartDVR Formula™ NetClient Mode 106

Click [Connect]. If the connection was successful, a progress ④bar will appear as shown below.

Adjust the volumes for best audio performance. SmartDVR Formula™ NetClient ⑤Mode 107 Netclient Minimize Function Press [Ctrl + M] at the main screen to minimize NetClient. Press [Ctrl + M] again to return. SmartDVR Formula™ Local Search 108 Local Search □1 Control Panel □2 Playback Control Panel □3 Screen Partition Panel □4 Search Data Process Panel SmartDVR Formula™ Local Search 109 □1 Control Panel The control panel consists of [Surveillance Mode] , [Load Data], [Save Still Image], [Print Still Image], and [Watermark Viewer]. Surveillance Mode: Switches to surveillance mode. Load Data: Opens a calendar you can use to search for recorded data by date. Save: Saves a captured image as a BMP file. Print: Prints out a captured image using printer. WaterMark Viewer: Opens WaterMarkViewer. □2 Playback Control Panel Playback: Playback at normal speed Pause: Pause Reverse Playback: Play backwards 2x Playback: Playback at 2x. 4x Playback: Playback at 4x 2x Reverse Playback: Playback in reverse at 2x. Play Next frame: Playback frame by frame Previous frame Reverse: Playback in reverse frame by frame

Only supported in 4 channel or 1 channel viewing mode. SmartDVR Formula™ Local Search 110 □3 Screen Partition Panel You can choose from 7 different screen partitions. You can also choose full screen mode, and sequential rotation display mode. □4 Search Data Process Panel Hour Button: Hour buttons in red indicate that data was recorded in that hour. Minute Bar: Displays the data of the selected hour in minutes(0 to 59 min). Recorded data is indicated in red. Search Mark Icon: It points to the current time of the recorded data. Time: It shows the current time position on the recorded data. Search Data Click [Load Data] in NetClient search screen. SmartDVR Formula™ Local Search 111 Red: Dates that have recorded data Blue: Current selected date.Grey: No recorded data MD ONLY: Load only the data recorded in motion detection mode. LOAD Button: Load all recorded data in the selected date. Remote Search Remote Search on LAN connection

Click the [Search] icon in NetClient main ①screen.

Click [Remote search] in NetClient search ②screen .

From the [Remote Search] window, select the DVR system you ③wish to connect to. The IP address and port number will be configured automatically as configured in [Configuration>Fixed IP & Dynamic IP].

Enter ID and Password. ④ Select the channel you wish to connect to. A maximum of 4 ⑤

channel search & playback is supported for a LAN connection. SmartDVR Formula™ Local Search 112

Click [Connect]. ⑥ If connected properly, dates with recorded data in the DVR ⑦

system will be indicated. Select a date you wish to search from the above calendar and click ⑧

[Load Data]. Click an hour button in red to load the data. The loading time depends on the bandwidth. It could take about 30

seconds up to 1 minute. Remote search using Modem

Click the [Search] icon in NetClient main screen. ① Click [Remote Search] in NetClient search screen. ② Enter the telephone number of the DVR system. ③ Enter ID and password. SmartDVR Formula™ Local Search ④

113 Select the channel you wish to connect to. Only 1 channel search ⑤

& playback is supported for a modem. Click [Connect]. ⑥ If connected properly, dates with recorded data in the DVR ⑦

system will be indicated. Select a date you wish to search from the above calendar and ⑧

click [Load Data. SmartDVR Formula™ Remote Search Main Screen 114 Remote Search Main Screen Remote Search screen is just about the same for both LAN mode and modem mode (except that only 1 channel search & playback is supported in modem mode) □1 Control Panel □2 Playback Control Panel □3 Screen Partition Panel □4 Search Data Process Panel SmartDVR Formula™ Remote Search Main Screen 115 □1 Control Panel Surveillance Mode: Switch to NetClient surveillance mode. Local Search: Search the recorded data saved in the NetClient system. Remote Search: Search the recorded data saved in the DVR System Save Button: Save an image from the selected channel as a BMP file. Watermarking function is not supported. □2 Playback control Panel Pause/Playback Button: Pause or play the video. Ref In remote search, 2X playback, frame by frame playback are not supported. Playback speed control: Controls the playback speed. □3 Screen partition panel Various screen partition modes are supported. Ref In remote search, only 1ch & 4ch screen partition mode is supported. SmartDVR Formula™ Remote Search Main Screen 116 □4 Data search process Panel Hour button: Hours that have recorded data are indicated in red. Minute Bar: Displays the data of the selected hour in minutes(0 to 59 min). Recorded data is indicated in red. Search Mark Icon: Points to the current time position on the recorded

data. Remote configuration Click [Remote configuration] button in NetClient main screen to open the [Remote setting] window.Enter the information about the server you are going to connect to. Click [Connect]. SmartDVR Formula™ Remote Search Main Screen 117 Remote configuration>General

Start Section ①Autostart : DVR program is automatically executed when the system is switched on.

Max size at starting ②You can configure the DVR program to start maximized in full screen to hide the other running programs.

Exit ③When exiting NetClient, it can be configured to close the NetClient program only, or shut down or reboot the DVR system.

Video / Audio setup ④Setup camera input type (NTSC/PAL) NTSC: Korea, USA, Japan, Australia (some region), North America (some region), etc. PAL: Regions outside of NTSC regions(China, Europe, South America etc.) SmartDVR Formula™ Remote Search Main Screen 118 Channel selection Select a channel to monitor. It is generally better to turn off the channels that are not connected to cameras. Resolution setup Choose image resolution. Choose from low resolution and high resolution. Ref NTSC – 320X240, 640X480 PAL – 360X288, 720X576 Remote configuration>Store

Store disk ①Displays hard disk drives installed on the system. (Removable disks not included.) (Check(√) the hard disk drive to be used for storage.) Note If the surveillance images are being stored in a disk drive which has an operating system installed, the system may stop or repeat rebooting when the disk drive is full. SmartDVR Formula™ Remote Search Main Screen 119

Disk information ②Displays information about the disk drive that was selected from

the list of storage devices. Overwrite ③

The oldest image data will be erased and new image data will be recorded when free disk space is less than the minimum free disk space (Default: 1024 MB). Notice You can use the HDD with disk space shortage errors with the overwrite function enabled. However this means that the oldest data will be automatically erased. Therefore it is recommended to backup important data in advance by using the Backup Manager.

Record setup ④You can start or stop recording each channel. Remote configuration>Network SmartDVR Formula™ Remote Search Main Screen 120 Displays the network configuration settings of the server system. Ref You cannot change the settings. Remote configuration> Maintenance

Windows information ①Displays Windows and system information of the DVR system

DVR version information ②Displays the board model and version of the DVR system.

System maintain ③At SmartDVR Formula™ startup, it checks the system files and stored data errors. Normal Check Mode: Checks the video data index and program files. Full Check Mode: Additional checks on data integrity are done. It takes longer to complete the checks. SmartDVR Formula™ Remote Search Main Screen 121

System auto reboot ④Setup to reboot the DVR System regularly. This is recommended for stable Windows operation and data verification. Remote configuration>Event

Sensor input ①Check [Enable the sensors] and configure the channel of camera and sensor input channel. Ref Sensor type NO (Normally Open) NO type sensors are normally open. The sensors close when something has been detected. No additional setup is required for NO types. NC (Normally Closed) NC type sensors are normally closed. The sensors open when something has been detected. You need to activate the NC mode

by clicking the [NC] button below each sensor number. SmartDVR Formula™ Remote Search Main Screen 122

Action ②You can select which action the DVR system will take when a sensor has been triggered. Enable event recording When sensor is triggered, the corresponding channel will start being recorded for some duration. Enable the warning sound When sensor is triggered, a warning sound (a wave file) will be played. Send e-mail at detection A still image taken at the time of the detection will be sent to an email address. The e-mail address is configured in [Configuration>E-mail].

Enable the digital output ③Various output devices (warning light, siren, warning speaker, etc.) will be activated when a sensor has been triggered. Select the channels for the digital output, and select NC/NO type for each channel. SmartDVR Formula™ Remote Search Main Screen 123 Remote configuration>E-mail

Mail server ①Enter the mail server address of the sender. Ref The e-mail function supports most mailing services, but some mailing services are not supported by the e-mail function.

Sender ②Enter the name and e-mail address of the sender.

Message recipients ③To: E-mail address of the recipient. CC: E-mail addresses of other recipients. BCC: E-mail addresses for blind carbon copy.

E-mail time setup ④Setup the e-mail response time after a sensor has been triggered.SmartDVR Formula™ WebClient Mode 124 SmartDVR Formula™ WebClient Mode WebClient allows you to receive surveillance images from a remote site, and monitor them without the need for installing any other programs. □1 Display mode In display mode, you can choose whether to use overlay or not. Use Overlay functionCheck to use the overlay function of the video card. Use the overlay function to remove incidental images. Note Overlay function may not work

properly with some video cards. Disable the overlay function in such a case. SmartDVR Formula™ WebClient Mode 125 □2 Screen Mode (Ch Split) Up to 7 different screen partitioning modes are supported depending on the number of channels. □3 P/T/Z Control panel When a P/T/Z camera is connected to the DVR Server, select the channel you wish to control, and click the control buttons in P/T/Z Control Panel to control the camera. Also, use the drag panel on the bottom to control the playback speed of the surveillance video. □4 Connection All connect: Connects to all available channels. If you wish to view a specific channel, click the channel you wish to view. SmartDVR Formula™ WebClient Mode 126 Connection to DVR systems (Static IP) Enter the IP address of the DVR server in your web browser E.g. Enter -http://61.107.32.82:26540 if the IP address of the server is 61.107.32.182. if this is your first time connecting through a web browser, the above message will pop up. Click [Yes] and it will take a few seconds to load the WebClient program. When the log-in window pops up, enter your ID and password registered in the DVR server. Click [Connect]. SmartDVR Formula™ WebClient Mode 127 Connecting to a DVR system registered to DHS Service Enter http://mybangsong.com/ in your web browser. Enter your DHS ID and click [Login]. The DHS ID has to be the same as the one used at DHS service registration. Ref If this is your first time connecting on a web browser, a message shown in the previous page will pop up to ask your permission to install the program. Click [Yes] to install. It will take a few seconds to load WebClient. After the program has been installed, the IP address and port number will be entered automatically. Enter your ID and password registered in the DVR system and click

[Connect]. SmartDVR Formula™ PDA NetClient Mode 128 SmartDVR Formula™ PDA NetClient Mode PDA NetClient S/W Manual 1) Description of Function Button explanation Power ON/ OFF client software. Screen PartitionSelect display mode between 1ch and 4ch(Quad). Full screen Support full screen, click the screen again, get back to previous screen. SmartDVR Formula™ PDA NetClient Mode 129 Connection Try to connect Dvr server and Disconnect remote connection. Configuration Set Remote access Information for Dvr Server. 2) 환경설정설명i. Input the access IP address of server. ii. CH: Input the channel number that want to access. iii. ID: Input access ID of server. iv. PW: Input access Password of server. v. To apply Network configuration, please click the “OK” button.SmartDVR Formula™ PDA NetClient Mode 130 3) PTZ Function Select the channel that want to control and then operate the PTZ camera by function button at 1ch full screen mode. Note To control PTZ camera by PDA Net program, installed PTZ camera and set up the PTZ configuration at DVR server in advance.

Direction Button: operate camera’s direction in left, right, ①up and down.

Zoom Button: Operate Camera Zoom In/Out manually. ② Focus Button: Operate Camera Focus manually. ③ Speed control Button: Control Pan/Tilt Speed. Compatible / Incompatible ④

131 Compatible / Incompatible SmartDVR Formula™ System RequirementDVR board Minimum Requirement Recommended CPU RAM CPU RAM S(30fps)

1.7Ghz or higher 128 MB or higher 1.7Ghz or higher 256 MB or higher SP(60fps) CEL 1.7 Ghz256 MB or higher CEL 2.4 Ghz256 MB or higher H(120fps) 1.7Ghz or higher 256 MB or higher 2.4Ghz or higher 512 MB or higher HP(240fps) 2.4Ghz or higher 512 MB or higher 2.4Ghz or higher 512 MB or higher Live120 (480/120fps) CEL 2.4 Ghz512 MB or higher P4 2.4 Ghz 512 MB or higher Live480 (480/480fps) P4 2.8 Ghz512 MB or higher P4 2.8 Ghz

512 MB or higher SmartDVR Formula™ Compatible Incompatible CPU Intel Pentium Process (x86, 1.7Ghz Over) - Intel Celeron 1.7Ghz or Higher - Intel Pentium IV - AMD Athlon XP Lower than Intel Pentium 1.7Ghz Process - Other than x86 Motherboard With one or more PCI slot, supporting Intel Pentium processor - Intel 81x Chipset - Intel 84x Chipset - Intel 85x Chipset - Intel 86x Chipset - VIA KM400 Intel CPU/ Via Chipset (694x & 694tx Series…etc) Intel CPU/ SIS Chipset - Gigabyte 81845GVM-RZ (Intel 845 Chipset) - Cyrix C3 Motherboard Compatible / Incompatible 132 <Mother board name> - Chaintech CT-9LIF3 - Chaintech CT-9LIF7 - Chaintech CT-9EJL2 SE - Chaintech M845GV - Unitech i865GV-RED - GigaByte 865GME - GigaByte 8IG 1000MK - ASUS P4P800-VM - ASUS P5P800-MX - Intel D915GEV - Intel D945GCZ - Intel D945GNT - Asrock P4i45GV - Asrock P4i65GV

- MSI Neo2 (Intel 865 Chipset) - Via Chipset - Sis Chipset - ATI Chipset - Nvidia Chipset - Uri Chipset VGA (Graphic Card) With 16MB or higher memory, Supporting 32Bit Color and YUY2 DirectX Mode - ATI Expert 2000 32MB SDRAM - ATI Radeon Series - nVidia Riva TNT2 Series - nVidia Geforce Series - Intel 845G/GL Graphics controller(OnBoard) - Intel 865G Graphics controller(Onboard) - Intel 81x Graphics Controller (On Board) or Intel i740 - VIA Chipset Onboard Graphic Controller - SIS Chipset Onboard Graphic Controoler - GeForce 4 MX440 AGP8X- ATI Radeon 7000, 9600 Sound Card Intel CPU/ Via Chipset Board - Gigabyte 81845GVM-RZ (Intel 845 Chipset) HDD HDD 5400RPM or higher Compatible / Incompatible 133 OS Windows XP(Professional, Home) Windows 2000 Series=(Real Display DVR driver must be installed

manually) Windows 98 Series Windows ME Mac OS OS/2 Compatible / Incompatible 134 NetClientCompatible Incompatible CPU Compatible with all CPU’s Motherboard Same as SmartDVR Formula™SiS, Via chipset motherboard VGA (Graphic Card) Same as SmartDVR Formula™-When use of Onboard SiS or Via chipset motherboard- SiS, Via chipset motherboard Sound Card All PCI and Onboard typeHDD All 5400RPM or higher HDD OS Windows XP recommend(Professional, Home) Windows 2000 Series Windows 98 Series Windows ME * Direct x8.0 or higher is necessary Mac OS, OS/2 RMA 135 Digital Security System Leader CCTV – Digital Recording System CCTV - Surveillance SECURITY – Network Security Products Intotech Inc. 13F, DMC R&D Center Bldg., Building Land Development District E3-2, Sangam-Dong Mapo-Gu Seoul

(121-270) Korea / TEL. +82 2 380 3704 / FAX.+82 2 380 3720 / http://intotech.co.krReturned Merchandise Authorization (RMA) Procedures and Policy1. RMA Policy• The warranty period of INTOTECH Inc. product is 12 months from onboarding date. • All RMA products to INTOTECH Inc. for service MUST have an RMA number. Failure on attaching an RMA number when product sent in will result in return of product to original sender without repair. • RMA number is valid for a period of 14 days from date of issue. RMA number will void thereafter. • RMA request must be fax at number: +82-2-380-3720 (Fax).2. RMA application procedures • User MUST obtain a RMA number from our Technical Support Department. • Request the RMA request form to sales@intotech.co.kr or request a fax copy by calling at phone number: +82-2-380-3704 . ☎

• Fill out the all field on the request form. • Must include product serial number. (Without serial number is refused to issue RMA number.) RMA 136 • Request form must be fax in at number: +82-2-380-3720 (Fax). • Upon received of the RMA product sent from you, send in the RMA product within the next 14 days. • During the request, you may call in for the status at phone number: +82-2-380-3704 or the status of the sent in RMA at fax number: +82-2-☎

380-3720 (Fax). 3. Packing Guideline• Returned items must be packed properly and safely, preferably in the original packaging. • The RMA number should be marked clearly on the outside of the package. • RMA request form as a written description of the unit's problem should be included. • Any item shipped to INTOTECH Inc. without RMA number listed on the package will be returned to the original sender. 4. Shipping Guideline• Shipment of returned items for all repairs should be prepaid and insured by customers via a carrier of their choice. • Products sent without prepaid freight will be returned to original sender immediately. • Any damages during transit are not covered under warranty. • INTOTECH Inc. is not liable for any delays or error on the part of any carrier. • We do not accept any C.O.D. shipments. • INTOTECH Inc. will pay for return freight. RMA 137 • All repaired products are to be shipped via standard EMS service. 5. Shipping Address INTOTECH Inc. 13F, DMC R&D Center Bldg., Building Land Development District E3-

2, Sangam-Dong Mapo-Gu Seoul(121-270) Korea Attn: Technical Support Department Tel: +82-2-380-37046. RMA received error• If any error is found in defective items received, INTOTECH Inc. representatives will inform customers to make an update in RMA status. Otherwise, the unapplied items will be returned to original sender without repair • All non-INTOTECH Inc. products will be sent back to customer without repair and prior notice at the cost of the sender • Any product that are out of warranty and, or have a broken seal will be return without repair unless repair is being charged to customer. Authorized by INTOTECH Inc. RMA 138 Digital Security System Leader CCTV – Digital Recording System CCTV - Surveillance SECURITY – Network Security Products Intotech Inc. 13F, DMC R&D Center Bldg., Building Land Development District E3-2, Sangam-Dong Mapo-Gu Seoul (121-270) Korea / TEL. +82 2 380 3704 / FAX.+82 2 380 3720 / http://intotech.co.krR M A (Returned Merchandise Authorization) Company Attention TEL Address No Model Serial No Problem Description Analysis of Factor Remarks