Net
APRIL2012
Freight Prepaid
on $10,000
Invoice
Manufacturer of Heavy Conveyor Belt
www.pricerubber.com
Price Rubber
WHOLESALE
Practical trucking limit is 13' diameter x 50,000 lbs. Pricecan manufacture one-piece rolls to 18' diameter x 100,000 lbs.
-
Belts made to a minimum length must be made slightly long. This overage will be shipped, but invoice will not exceed 2%.
Tailor made Belt
Going to Work!
from any compound on anyfabric, made to width and lengthto capacity of hauling equipment. Exact specifications yieldmaximum service in the mostdemanding applications. Long,one-piece rolls eliminate fieldsplicing. Because belts are made towidth, they run true from thestart. Our special nylon impression bottom gives extradrive traction and helps freefrozen idlers for better tracking and smoother, morecare-free operation. It doesn’t get anybetter than this!
Our Specialty is
WarrantyAll merchandise is guaranteed against defective materials and workmanship for the life of the product.
Terms of SaleNet 30 days, or cash with order. No COD shipments.
PriceWill drop ship any product from any shipping point.
Price Rubber Corp.©Copyright 2012 * Prices are subject to change without notice. Please call for current pricing and availability.
Belt Plant (334) 277-5470 2733 Gunter Park Dr. W. (800) 633-1470 Montgomery, AL 36109 Fax: (334) 271-3194 Email: [email protected] Email: [email protected] Email: [email protected] Email: [email protected]
Email: [email protected] Plant (256) 582-3134 3805 Morrow St. (800) 633-2284 Guntersville, AL 35976 Fax: (256) 582-0847 Email: [email protected] Email: [email protected]
Warehouses 2953 Fleetbrook Dr. (901) 332-9360 Memphis, TN 38116 (800) 331-9360 Fax: (901) 332-9366 Email: [email protected] Email: [email protected]
901 E. Kennedale Pkwy (817) 572-0253 Kennedale, TX 76060 (800) 821-0668 Fax: (817) 478-0360 Email: [email protected] Email: [email protected]
2556 South 2570 West (801) 956-0077 West Valley City, UT 84119 (888) 597-7423 Fax: (801) 956-0117 Email: [email protected] Email: [email protected]
Email: [email protected]
1
Freight Prepaid on $10,000 invoice within lower 48 states, or to port of exit.
2
Rubbers Sp. Gr Butyl .92 EPDM .86 Hypalon 1.10 Mineral 1.04 Natural .92 Neoprene 1.23 Nitrile 1.00 Polybutadiene .94 Syn. Natural .92 SBR .94 Silicone .98 Thiokol 1.27
Fillers Sp. Gr. AI. Hydrate 2.42 Barytes 4.45 Ca. Carbonate 2.70 C. Black 1.80 Clays 2.60 Graphite 2.25 Kaolin 2.60 Lime 2.20 Mg. Carbonate 2.22 Mica 2.95 Soapstone 2.72 Talc 2.72 Titanium Di. 3.93
Processing Sp.Gr. Aids Carnauba Wax .99 DOP Oil .98 Factice 1.06 Mineral Oil .84 Pine Oil .93 Tall Oil .98 Parafin Wax .90 Petrolatum .84 Pine Tar 1.08 Rosin 1.08
Vulcanizers Sp.Gr. Mg. Oxide 3.32 Sulfur 2.07 Zn Oxide 5.57
Miscellaneous Sp.Gr. Am. Bicarbonate 1.58 Asbestos 2.47 Coal Tar 1.18 Cork .80 Cotton Flock 1.25 Gelatin 1.27 Rubber Dust 1.20 Iron Oxide 5.14 Lead 11.34 Lignin 1.30 Mg. Carbonate 2.22 Castor Oil .96 Cotton Seed Oil .92 Palm Oil .88 Pumice 2.35 Shellac 1.10 Sodium Bicarbonate 2.20 Stearic Acid .85 Urea 1.34 Whiting 2.62 Wood Flour 1.25 Zinc Stearate. 1.05
AirOperatedRam
Like a bakery, thousands of recipes are written around hundreds of ingredients, each intended to contribute some-thing to the finished product.
Rubber can be made soft orhard, flexible or rigid, elas-tic or tough, alive or dead- liquid, sponge, almost any color and resistant to sunlight, electrical current, sub-zero temperature, heat, and many chemicals and oils. Rubber serves everywhere man goes!
DropDischarge Door
MixingRotors
LoadingHopper
Price RubberCompounding We supply many other
manufacturers with precisecompounds for their products 3Dependable quality 3Repeatabil i ty 3Prompt del ivery 3Reasonable cost
Guntersvi l le Mixing Plant(256) 582-3134(800) 633-2284
Fax: (256) 582-0847
3
Tensile is a measure of force required to break a material. In rubber, generally a dumbbell sample with a 1/4” x 1/4” cross section (neck) is broken and pounds per square inch are calculated.
Elongation is the “stretch” of a material at break, expressed as a percent of the relaxed original. Modulus is a measure of force required to stretch a materiala particular amount. In rubber, generally a sample is stretched 300% and the necessary force (pounds per square inch) is calculated. Durometer is a measure of hardness, measured with a plunger and read on a gauge. A rubber band might read 35, a tire tread about 60 and a shoe heel about 70 durometer.
Specific Gravity (mass) is weight, compared withan equal volume of water (taken as 1.0).
Belt Compounds Stk. Compound Ten. Elon. Mod. Duro. Sp.Gr.
16 400º Chlorobutyl 1900 650 950 65 1.14
20 Tan natural 2400 775 400 46 1.22
21 PRC #1 SBR 3050 580 1500 64 1.14
22 PRC #2 SBR 2400 640 1100 60 1.14
23 300º F SBR 2700 580 1300 63 1.14
24 PRC #2 MOR 2400 600 1100 62 1.15
26 70 duro. SBR 2800 550 1100 70 1.16
29 Hyflex abrasion 3000 630 1300 65 1.14
31 Polar Bear - 80º F 2590 560 1300 63 1.14
32 MSHA abrasion 2100 525 1000 65 1.25
33 MSHA SBR 1800 540 1000 66 1.38
34 MSHA flameout 1500 500 850 63 1.54
35 MSHA Nitrile 2000 500 1100 65 1.35 36 MSHA weather 1600 450 1150 70 1.37
37 An./Veg. waste 2200 510 1100 62 1.16
38 Alumina 3000 550 1300 65 1.17
44 EPDM 350º F 1500 500 1100 65 1.17
61 Nitrile 1600 500 1150 62 1.25
96 Non-marking SBR 1200 400 500 55 1.32
99 Hard SBR 1700 210 zero 80 1.17
Rubber Carefully formulatedcompounds give maxi-mum service in theintended application. These recipes handlethe products conveyedby the belts shown inthe following pages.
We have no minimums on invoicing
or shipping . . . you get what you need
without penalty.
We slit, lace, punch, vulcanize, and
add cleats or V-guides at reasonable
cost. We couple all hoses.
We drop ship to anywhere, using
standard forms, blank forms, or your
forms, as you instruct.
We manufacture most special
products in modest minimums at
regular prices.
Pricing is for shipments from any
warehouse to any destination, any product
mix, in any quantity.
Price
4
5
Allowable Working Tension
(AWT) @ 1⁄10 fabric break American Lab rating
No. Fiber Warp Weft Ga.''
Plain weave Lbs. per inch
75 Polyester 84 60 100 .023
90 '' 110 68 125 .031
110 '' 128 80 145 .033
Atlas multiwarp 200 Polyester 243 97 238 .047
250 '' 290 94 275 .064
300 '' 358 94 316 .066
Allowable Working Tension (AWT) @ 1⁄10 fabric break
Euro-Asian Lab rating
No. Fiber Warp Weft Ga.''
Plain weave Lbs. per inch
100 Poly/Nylon 73 34 75 .024
125 '' 86 35 85 .024
75 160 '' 105 40 102 .028
90 200 '' 131 43 122 .034
110 250 '' 165 43 146 .040
Atlas multiwarp fabrics yield More Tons per Dollar!
American fabrics are numbered at AWT (Allowable Working Tension) of 1/10 of warp break in lbs. per inch of width (PIW). Euro-Asian fabrics are numbered at AWT of 1/10 break of warp plus weft in Newtons per millimeter (N/mm). One N/mm = .571 lbs. /in. Thus Euro-Asian fabrics are numbered more than twice as high as American.
Fabrics for Belts 70%Warp
+ Weft
70%Warp
+ Weft
6
110 lb. Polyester is used more than any other fabric in general industry. From hay to quarry stone, this fabric is strong, flex-ible and plain-woven for straight tracking, support of materials between idlers, and uniform toughing.
* Price Rubber Corp. The industry leaderin setting productstandards.
2# Trucking limit is 13' dia. x 50,000 lbs.
Stk. 22 on 110 lb. Polyester Carcass Covers PIW 36'' 48'' Gauge'' 2 Ply 1/32 x bare .2394 8.62 11.49 .137 220 1/32 x 1/32 .2869 10.33 13.78 .169 1/16 x bare .2869 10.33 13.78 .169 1/8 x bare .3825 13.77 18.35 .231 1/8 x 1/16 .4778 17.20 22.93 .294 3/16 x bare .4778 17.20 22.93 .294 3/16 x 1/16 .5731 20.63 27.50 .356 1/4 x 1/16 .6683 24.06 32.08 .419 3 Ply 1/8 x bare .4783 17.22 22.96 .284 330 1/8 x 1/16 .5736 20.65 27.53 .347 3/16 x bare .5736 20.65 27.53 .347 3/16 x 1/16 .6689 24.08 32.10 .409 1/4 x bare .6689 24.08 32.10 .409 1/4 x 1/16 .7642 27.51 36.68 .472 4 Ply 3/16 x 1/16 .7342 26.43 35.24 .442 440 1/4 x bare .7342 26.43 35.24 .442 1/4 x 1/16 .8242 29.86 39.82 .505 3/8 x 1/8 1.1150 40.16 53.54 .692 Any width to 72 ' ' Any Quantity Per Foot
Æ
$ $ $
*PRC
Conveyor Belt
7
NET prices on heavy bel t (pages 6-20)are for any quant i ty f rom warehouse inventor ies , prepared any way you instruct . Large and ta i lor-made bel ts of ten gain economy of manufacture . Cal l the factory for current costs on these heavy bel ts . They are pr iced from the commodity market a t that t ime, of ten at a savings.
200 lb. Atlas multiwarpgives extra strength withfewer plies. In heavyservice, this means moretons per dollar. In under-ground work, this fabric is popular because of the light weight and flexibility. This is the choice of those seeking maximum value.
There are millions of feet of these belts running right now!Still the American Standard.
2 Ply
3 Ply
4 Ply
5 Ply
Stk. 22 on 200 lb. Atlas Carcass Covers PIW 36'' 48'' Gauge'' $ $ $ 1/8 x 1/16 .5358 19.29 25.72 .322 400 3/16 x 1/16 .6311 22.72 30.30 .384 1/4 x 1/16 .7264 26.15 34.87 .447 1/4 x 1/16 .8514 30.65 40.87 .514 600 5/16 x 1/16 .9469 34.09 45.45 .576 3/8 x 1/8 1.1370 40.95 54.60 .701
1/4 x 1/16 .9461 34.06 45.41 .561 5/16 x 1/8 1.1360 40.92 54.56 .686 800 3/8 x 1/8 1.1230 44.35 59.13 .748
3/8 x 1/8 1.3260 47.75 63.67 .795 1000 1/2 x 1/8 1.5170 54.61 72.82 .920 1/2 x 3/16 1.6120 58.04 77.39 .983
Any width to 72 ' ' Any Quantity Per Foot
Belts made to a minimum length must be made slightly long. This overage will be shipped, but invoice will not exceed 2%.
2# Conveyor Belt
Æ
Pacific Conv ey o r Be l t
8
2#
Widely used in moderate service handling sand, gravel, and readymix. Made from American
materials to American standards, with PRC #2 Stk. in skims and covers, to standard gauge. The
all-Polyester fabric is 20% stronger than foreignfabrics of the same grade. With smooth topand Nylon impression bottom, for greater
traction, in a belt made to width, Pacific always runs true from the start. Economy is achieved by volume production with people of experience and skill, and in expert American craftsmanship. We slit, punch, or lace to suit!
Special 3% discount for random production length rolls (approx. 1,000 �.) or for any warehouse rolls “as is” in any length.
Prepaid
Freight on
$10,000
Invoice!
Made inUSA
PIW is Per Inch of Width, per foot.
Stk. 95 on #75 Polyester fabr ic
.274
.336
.379
.442
Carcass Covers PIW 24'' 30'' 36'' 42'' 48'' 60'' Gauge'' 2 Ply 1/8 x 1/16 3/16 x 1/16
3 Ply 3/16 x 1/16 1/4 x 1/16
Any width to 72'' Per Foot - Any Quantity From Stock.
Æ
PIW is Per Inch of Width, per foot.
Made by the Mile!
24.9530.19
.5803
.667517.4120.03
20.8924.03
24.3728.04
27.8532.04
34.8240.05
13.9316.02
.4158
.5031 9.9812.07
12.4715.09
14.9718.11
17.4621.13
19.9624.15
9
Stk. 24 on 110 lb. Polyester Carcass Covers PIW 24'' 30'' 36'' Gauge'' 2 Ply 1/8 x 1/16 .4828 11.59 14.48 17.38 .294 220 3/16 x bare .4828 11.59 14.48 17.38 .294 3/16 x 1/16 .5794 13.91 17.38 20.86 .356
3 Ply 1/8 x 1/16 .5792 13.90 17.37 20.85 .347 330 3/16 x bare .5792 13.90 17.37 20.85 .347 3/16 x 1/16 .6758 16.22 20.27 24.33 .409 4 Ply 3/16 x 1/16 .7411 17.79 22.23 26.68 .442 440 1/4 x 1/16 .8378 20.11 25.13 30.16 .505
Stk. 24 on 200 lb. Atlas 3/16 x 1/16 .6378 15.30 19.13 22.96 .384 1/4 x 1/16 .7342 17.62 22.03 26.44 .447 3/16 x 1/16 .7631 18.31 22.89 27.47 .451 1/4 x 1/16 .8597 20.64 25.79 30.95 .514
Cut edge to 72'' Any Quantity Per Foot
Atlas
2 Ply 400
3 Ply 600
Log Trough Bel ts - Stk. 24 on 200 lb . Atlas Atlas Covers PIW 24'' 30'' 36'' 42'' 48'' 60'' Gauge''
2/400 3/16 x bare .5408 12.98 16.23 19.47 22.72 25.97 32.46 .322 3/600 1/4 x bare .7631 18.31 22.89 27.47 32.04 36.63 45.79 .451 4/800 5/16 x bare .9544 22.90 28.63 34.36 40.08 45.81 57.26 .561 5/1000 3/8 x bare 1.1450 27.49 34.37 41.24 48.11 54.98 68.73 .670
Cut edge to 72 ' ' Any Quantity Per Foot
$ $ $ $
$ $ $ $ $ $ $
PRC #2 MORTurpene Resistant
Makes i t PRC #2 MOR Bet ter!
Industry Standard
From sawmill to finished paper, this beltserves the timber industry.
Wood Yard
Æ
Æ
10
PriceCleat
PriceCleat
. . . a product of Pride!
We will skive the cleats from both edges of this belt for up to 12'' deep for $2 per foot net.
A very popular and hard working design for incline conveyors handling gravel, sand, fertilizer, or sawdust. Full 1/4'' x 1/4'' V-cleats on 6'' centers are molded with the covers for extra long life.
Stk. 24 on 110 lb. Polyester Carcass Covers PIW 24'' 30'' 36'' Gauge''
2 Ply 3/16 x bare .6206 15.07 18.83 22.60 .544 220 3/16 x 1/16 .7244 17.39 21.73 26.08 .606 3 Ply 3/16 x bare .7242 17.38 21.72 26.07 .597 330 3/16 x 1/16 .8208 19.70 24.62 29.55 .659
4 Ply 3/16 x bare .7894 18.95 23.68 28.42 .630 440 3/16 x 1/16 .8861 21.27 26.59 31.90 .692 Cut edge to 60 ' ' Any Quantity Per Foot
$ $ $ $
Æ
PRC #2 MOR Turpene resistant widely used in handling pine chips,soybeans, corn, wheat or sorghum in agriculture harvesting and processing.
Warehouse inventories are in#2 MOR Turpene resistant #24
stock, but the PriceCleat pattern is available on almost
any tailor-made belt with3/16'' covers, in any
compound (see page 3).
11
Many crusher superintendents have used this belt for decades where service is hard. Before Hyflex was developed, it was the best the rubber industry had to offer. It still does an excellent job on primary crushers in handling the heavy, jagged quarry stone.
This compound resists cutting, tearing, gouging, and on Atlas multi warp fabrics, these belts yield more Tons per Dollar than ever before!
Still an Industry Standard!
Value that Lasts!
1 Belt Stk. 21 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.'' $ $ $ 2 Ply 1/8 x 1/16 .4903 17.65 23.53 .294 220 3/16 x 1/16 .5889 21.20 28.27 .356
3 Ply 3/16 x 1/16 .6861 24.70 32.93 .409 330 1/4 x 1/16 .7847 28.25 37.67 .472 4 Ply 1/4 x 1/16 .8503 30.61 40.81 .505 440 3/8 x 1/8 1.1460 41.27 55.03 .692 5 Ply 1/4 x 1/16 .9156 32.96 43.95 .538 550 3/8 x 1/8 1.2120 43.63 58.17 .725 1/2 x 1/8 1.4090 50.74 67.65 .850 Cut edge to 72'' Any Quantity Per Foot
Stk. 21 on 200 lb. Atlas Carcass Covers PIW 36'' 48'' Ga.'' $ $ $ 2 Ply 1/8 x 1/16 .5486 19.75 26.33 .322 400 3/16 x 1/16 .6472 23.30 31.07 .384
3 Ply 3/16 x 1/16 .7733 27.84 37.12 .451 600 1/4 x 1/16 .8722 31.40 41.86 .514 3/8 x 1/8 1.1680 42.06 56.08 .701 4 Ply 1/4 x 1/16 .9667 34.80 46.40 .561 800 3/8 x 1/8 1.6230 45.46 60.62 .748
5 Ply 1/4 x 1/16 1.0610 38.20 50.93 .608 1000 1/2 x 1/8 1.5550 55.98 74.64 .920 Cut edge to 72'' Any Quantity Per Foot
Material WeightsMaterial Lbs./Cu. Ft.
Wood Chips 20Coke 30Corn 45Rice 45Soybeans 45Wheat 50Coal 50Clay 75Bauxite 80Salt 95Limestone 95Cement 100Sand 100Granite 100Gravel 110Phosphate 110Slag 110Copper Ore 140Iron Ore 150
Belts made to a minimum length must be made slightly long. This overage will be shipped, but invoice will not exceed 2%.
PRC #
Æ
Æ
12
20 Tons
Going to Work!
Practical trucking limit is 13' diameter x 50,000 lbs. Pricecan manufacture one-piece rolls to 18' diameter x 100,000 lbs.
In abrasion, these belts out wear any other by up to 25%. This longer life in handling iron ore, bauxite, slag, rock and in gold mining truly is impressive. Special fabric treatment for acids. Our very best!
Tailor - made for you!
Stk. 29 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.'' $ $ $ 2 Ply 1/8 x 1/16 .5072 18.26 24.34 .294 220 3/16 x 1/16 .6106 21.98 29.30 .356 1/4 x 1/16 .7139 25.70 34.27 .419
3 Ply 3/16 x 1/16 .7089 25.52 34.03 .409 330 1/4 x 1/16 .8122 29.24 38.99 .472 3/8 x 1/8 1.1230 40.41 53.88 .659 4 Ply 1/4 x 1/16 .8778 31.60 42.13 .505 440 3/8 x 1/8 1.1880 42.76 57.02 .692 1/2 x 1/8 1.3950 50.21 66.94 .817 5 Ply 3/8 x 1/8 1.2530 45.12 60.16 .725 550 1/2 x 1/8 1.4600 52.56 70.08 .850 Cut edge to 72'' Any Quantity Per Foot
Stk. 29 on 200 lb. Atlas Carcass Covers PIW 36'' 48'' Ga.'' $ $ $ 2 Ply 1/8 x 1/16 .5653 20.35 27.14 .322 400 3/16 x 1/16 .6686 24.07 32.10 .384 1/4 x 1/16 .7722 27.80 37.06 .447 3 Ply 3/16 x 1/16 .7964 28.67 38.22 .451 600 1/4 x 1/16 .8997 32.39 43.18 .514
4 Ply 1/4 x 1/16 .9942 35.79 47.72 .561 800 3/8 x 1/8 1.3040 46.96 62.61 .748 1/2 x 1/8 1.5110 54.40 72.53 .873
5 Ply 1/4 x 1/16 1.0890 39.19 52.26 .608 1000 3/8 x 1/8 1.3990 50.36 67.14 .795
Cut edge to 72'' Any Quantity Per Foot
The Top! Hyflex
Æ
Æ
PriceFlex Belt
13
Stk. 21 PRC # 1 on Straight-Warp Polyester Carcass Covers 36'' 42'' 48'' 60'' Gauge''
440 31/4 x 1/8 40.79 47.59 54.39 67.98 .523 5/16 x 5/32 46.12 53.81 61.50 76.87 .617 3/8 x 3/16 51.46 60.03 68.61 85.76 .711
3 warehouse inventory
$ $ $ $
Our best PRC #1 stock on Straight-Warp Polyester Cord. Lashed together like a log raft, this fabric is almost impossible to separate from the belt covers. Strong length-wise polyester cords have no crimp, giving great strength with very little stretch. Cover stocks are pressed through the carcass for a unique bond far beyond plied belt. High flexibility with rip and impact resistance make this belt hard to hurt. Lacings seat with exceptional grip. Preferred in hard applications, this belt gives very long, trouble-free service with little concern for early failure.
Stk. 37 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.'' $ $ $ 2 Ply 1/16 x 1/16 .4078 14.68 19.57 .231 220 1/8 x 1/16 .5125 18.45 24.60 .294 3 Ply 1/8 x 1/16 .6114 22.01 29.35 .347 330 3/16 x 1/16 .7164 25.79 34.38 .409
Widths 24'' to 72'' Any Quantity Per Foot
Waste Treatment Designed to handle humanwaste in municipal disposalsystems. This compound does a good job in a terrible business.. . . a belt that lasts!
Æ
14
MSHANitrile
Coal and Grain Utilities often spray coal with fuel oil to control dust, while elevators handle a wide variety of vegetable oils. This Nitrile compound serves well in both industries, and meets MSHA specs, for above ground service. Carcass has exceptional strength for lacings.
All Price Coal Belts meet ASTM D257 conductivity tests of OSHA
Plies Covers PIW 36'' 42'' 48'' 54'' 60'' 72'' Gauge''
2 Ply 1/16 x 1/16 .4689 16.88 19.70 22.51 25.32 28.14 33.76 .231 220 1/8 x 1/16 .5969 21.49 25.08 28.66 32.24 35.82 42.99 .294 3/16 x 1/16 .7253 26.11 30.46 34.81 39.16 43.51 52.21 .356 3 Ply 1/16 x 1/16 .5753 20.71 24.16 27.62 31.07 34.52 41.42 .284 330 1/8 x 1/16 .7033 25.32 29.54 33.76 37.99 42.21 50.65 .347 3/16 x 1/16 .8317 29.94 34.92 39.91 44.90 49.89 59.89 .409
2 Ply 1/16 x 1/16 .5272 18.98 22.14 25.31 28.47 31.63 37.69 .259 400 1/8 x 1/16 .6553 23.59 27.52 31.45 35.39 39.32 47.18 .322 3/16 x 1/16 .7833 28.20 32.90 37.60 42.30 47.00 56.40 .384
3 ply 1/8 x 1/16 .7908 28.47 33.21 37.96 42.70 47.45 56.94 .389 600 3/16 x 1/16 .9189 33.08 38.59 44.11 49.62 55.13 66.16 .451 1/4 x 1/16 1.0470 37.69 43.97 50.26 56.54 62.82 75.38 .514
4 Ply 1/8 x 1/16 .8853 31.87 37.18 42.49 47.87 53.12 63.74 .436 800 3/16 x 1/16 1.0130 36.48 42.56 48.64 54.72 60.80 72.96 .498 1/4 x 1/16 1.1410 41.09 47.94 54.79 61.64 68.49 82.19 .561
Any width to 72'' Any Quantity Per Foot
$ $ $ $ $ $ $
Æ
Stk. 35 on 110 lb. Polyester
Stk. 35 on 200 lb. Atlas Multiwarp
15
Stk. 34 on 200 lb. Atlas Multiwarp Plies Covers PIW 36'' 42'' 48'' 54'' 60'' 72'' Gauge'' 2 Ply
400 1/8 x 1/16 .5800 20.88 24.36 27.84 31.31 34.79 41.75 .322
3/16 x 1/16 .6794 24.46 28.53 32.61 36.69 40.76 48.91 .384
3 ply 1/8 x 1/16 .7206 25.94 30.27 34.59 38.92 43.24 51.89 .389 600 3/16 x 1/16 .8200 29.52 34.45 39.37 44.29 49.21 59.05 .451 1/4 x 1/16 .9197 33.11 38.62 44.14 49.66 55.18 66.21 .514
4 Ply 1/8 x 1/16 .8294 29.86 34.84 39.82 44.80 49.77 59.73 .436 800 3/16 x 1/16 .9292 33.45 39.02 44.59 50.17 55.74 66.89 .498 1/4 x 1/16 1.0290 37.03 43.20 49.37 55.54 61.71 74.05 .561
Any width to 72'' Any Quantity Per Foot
This new specification for underground coal belt is intended to make mining safer. After five minutes exposure to flame, this flameout compound will self-extinguish producing far less smoke and fumes than earlier specs. Strong, highly flexible and tough, this belt will serve well at the lowest possible cost per ton.
New 2010 Specs!
MSHA Underground
$ $ $ $ $ $$
Coal Belt
MSHA Approved Under 30 C.F.R. Part 14
Mine Star
Æ
16
Belts made to a minimum length must be made slightly long. This overage will be shipped, but invoice will not exceed 2%.
Above Ground
Coal Belt
$ $ $
Stk. 36 on 110 lb. Polyester Carcass Covers PIW 36'' 42'' Gauge'' 2 Ply 1/8 x 1/16 .6550 23.58 27.51 .294 3/16 x 1/16 .7989 28.76 33.55 .356
3 Ply 1/8 x 1/16 .7664 27.59 32.19 .347 3/16 x 1/16 .9103 32.77 38.24 .409
Stk. 36 on 200 lb. mult iwarp 1/8 x 1/16 .7131 25.67 29.95 .322 3/16 x 1/16 .8572 30.86 36.00 .384 1/8 x 1/16 .8536 30.73 35.86 .389 3/16 x 1/16 .9978 35.92 41.90 .451
Any width to 72'' Any Quantity Per Foot
2 Ply
3 Ply
Æ
For above ground service, stock 36resists oxiation of high altitudes, strongsunlight, ultraviolet radiation, and aridclimate. Resists high, dry climate
$ $ $Some coal seams are
full of highly abrasive grit, rock, slag and dirt. This special compound extends the life of the belt to save money and to avoid the costly time and expense of replacement.
Quality – Economy
Stk. 32 on 110 lb. Polyester Carcass Covers PIW 36'' 42'' Gauge'' 2 Ply 1/8 x 1/16 .5900 21.24 24.78 .294 3/16 x 1/16 .7161 25.78 30.08 .357 3 Ply 1/8 x 1/16 .6958 25.05 29.22 .347 3/16 x 1/16 .8219 29.59 34.52 .409
and on Atlas 200 lb. multi warp 1/8 x 1/16 .6483 23.34 27.22 .322 3/16 x 1/16 .7744 27.88 32.52 .384 1/8 x 1/16 .7831 28.19 32.89 .389 3/16 x 1/16 .9092 32.73 38.19 .451
Any width to 72'' Any Quantity Per Foot
2 Ply
3 Ply
AbrasionUnderground
This compound will notcrack, flake, or brittleanywhere in America!
Æ
17
Several of our large belt presses are equipped with nylon carrier belts, which leave a fine, gauzie texture on the bottom of the belt at manufac-ture. This texture isn’t just pretty…it serves a purpose. It will grip steel drive pulleys better, often making lag-ging unnecessary. And, it will cause reluctant idlers to turn rather than drag. This decreases drag on the con-veyor, and allows the belt to track more accurately.
Best yet! It doesn’t cost anything! We do it all the time. All you have to do is ask!
Ny l on Impression
for Extra Traction
Operating belt temperatures are established by laboratory heat aging for one week at the stated temperature, without significant degrading of compound physicals. Belts may serve well above these temperatures if they are operated intermittently, allowed to cool on the return side, or “hosed” to reduce heat. No elastomer will endure more than our #16 Chlorobutyl at 400º F continuous operation. Nylon and polyester fabrics will melt at 500º F.
HEAT
18
300 º F SBR
Not oil resistant
A high-grade SBR compound with lots of anti- oxidants to boost the heat range this belt will handle. Popular for hot sand, cement, and iron ores.
Stk. 23 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.'' 2 Ply 1/8 x 1/16 .4828 17.38 23.17 .294 220 3/16 x 1/16 .5794 20.86 27.81 .356 3 Ply 3/16 x 1/16 .6758 24.33 32.44 .409 330 1/4 x 1/16 .7725 27.81 37.08 .472 4 Ply 1/4 x 1/16 .8378 30.16 40.22 .505 440 3/8 x 1/8 1.1280 40.60 54.14 .692 5 Ply 3/8 x 1/8 1.1930 42.96 57.28 .725 550 1/2 x 1/8 1.3860 49.92 66.57 .850
Stk. 23 on 200 lb. Atlas 2 Ply 3/16 x 1/16 .6378 22.96 30.61 .384 400 1/4 x 1/16 .7344 26.44 35.25 .447
3 Ply 1/4 x 1/16 .8597 30.95 41.27 .514 600 3/8 x 1/8 1.1500 41.40 55.19 .701 4 Ply 1/4 x 1/16 .9544 34.36 45.81 .561 800 3/8 x 1/8 1.2440 44.88 59.73 .748
5 Ply 3/8 x 1/8 1.3390 48.20 64.27 .795 1000 1/2 x 1/8 1.5320 55.16 73.55 .920
Cut edge to 72'' Any Quantity Per Foot
$ $ $
Æ
350 º F EPDM
Stk. 44 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.'' 2 Ply 1/8 x 1/16 .6222 22.40 29.87 .294 220 3/16 x 1/16 .7572 27.26 36.35 .356 3 Ply 3/16 x 1/16 .8658 31.17 41.56 .409 330 1/4 x 1/16 1.0000 36.03 48.04 .472
4 Ply 1/4 x 1/16 1.0660 38.38 51.18 .505 440 3/8 x 1/8 1.4710 52.97 61.79 .692
$ $ $
Often used in foundry and ore service where oil is not a factor. Very flexible, with top adhesions, and highly weather resistant.
Not oilresistant
Stk. 44 on 200 lb. Atlas 2 Ply 3/16 x 1/16 .8156 29.36 39.14 .384 400 1/4 x 1/16 .9506 34.22 45.62 .447
3 Ply 1/4 x 1/16 1.0880 39.18 52.23 .514 600 3/8 x 1/8 1.4930 53.76 71.68 .701
4 Ply 1/4 x 1/16 1.1830 42.58 56.77 .561 800 3/8 x 1/8 1.5870 57.16 76.21 .748
Widths 24'' to 72'' Any Quantity Per Foot
Æ
19
OurBest!
These two bel ts are a t the Top and the Bottom of what e las tomers can do!
For hot sandand foundry use.We’ve tried manyother compoundsbut always comeback to this. Nothing elsetakes the heatas well. ThisChlorobutyldoes thejob!
Stk. 16 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.''
$ $ $ 2 Ply 1/8 x 1/16 .8092 29.13 38.84 .294 220 3/16 x 1/16 .9956 35.84 47.78 .356 3 Ply 1/8 x 1/16 .9356 33.63 44.84 .347 330 3/16 x 1/16 1.1200 40.34 53.78 .409
Stk. 16 on 200 lb. Atlas 2 Ply 1/8 x 1/16 .8672 31.22 41.63 .322 400 3/16 x 1/16 1.0530 37.93 50.58 .384
3 Ply 3/16 x 1/16 1.2080 43.48 57.97 .451 600 1/4 x 1/16 1.3940 50.19 66.92 .514
Cut edge to 72'' Any Quantity Per Foot
Cold to 80˚ below Zero!
Polar Bear Stk. 31 on 110 lb. PolyesterCarcass Covers PIW 36'' 48'' Ga.'' $ $ $ 2 Ply 1/8 x 1/16 .5106 18.38 24.51 .294 220 3/16 x 1/16 .6150 22.14 29.52 .356 3 Ply 3/16 x 1/16 .7136 25.69 34.26 .409 330 1/4 x 1/16 .8181 29.45 39.27 .472 4 Ply 3/16 x 1/16 .7792 28.05 37.40 .442 440 1/4 x 1/16 .8833 31.80 42.41 .505
Stk. 31 on 200 lb. Atlas 2 Ply 3/16 x 1/16 .6731 24.23 32.31 .384 400 1/4 x 1/16 .7775 27.99 37.32 .447
3 Ply 3/16 x 1/16 .8011 28.84 38.45 .451 600 1/4 x 1/16 .9053 32.59 43.46 .514 Cut edge to 72'' Any Quantity Per Foot
Special compounds remain flexible below freezing. Will not crack and break. This belt will work below what most operators can stand.
Æ
Æ
Æ
Æ
400 º F CHLOROBUTYL
20
Non-drying
350 º F
Alumina Belt
A 100% Nitrile compound will handle hot asphalt and petroleum based products to 350º F. This belt will serve well in a highly destructive chore.
Heat and Oil to 350º F.
Made to handle the drying action of Alumina, this belt remains flexible and alive. Covers do not crack, flake, or become brittle.
Stk. 61 on 110 lb. PolyesterCarcass Covers PIW 24'' 36'' Ga.'' $ $ $ 2 Ply 1/16 x 1/16 .5339 12.81 19.22 .231 1/8 x 1/16 .6867 16.48 24.72 .294 220 3/16 x 1/16 .8394 20.14 30.22 .356
3 Ply 1/8 x 1/16 .8008 19.22 28.83 .347 330 3/16 x 1/16 .9536 22.89 34.33 .409 1/4 x 1/16 1.1060 26.55 39.83 .472
Cut edge to 72'' Any Quantity Per Foot
Stk. 38 on 110 lb. PolyesterCarcass Covers PIW 24'' 36'' Ga.''
$ $ $ 2 Ply 1/8 x 1/16 .5667 13.60 20.40 .294 220 3/16 x 1/16 .6864 16.48 24.71 .356 3 Ply 3/16 x 1/16 .7903 18.97 28.45 .409 330 1/4 x 1/16 .9100 21.84 32.76 .472
Stk. 38 on 200 lb. Atlas 2 Ply 1/8 x 1/16 .6250 15.00 22.50 .322 400 3/16 x 1/16 .7447 17.87 26.81 .384
3 Ply 3/16 x 1/16 .8775 21.06 31.59 .451 600 1/4 x 1/16 .9972 23.94 35.90 .514 4 Ply 1/4 x 1/16 1.0920 26.20 39.31 .561 800 3/8 x 1/8 1.4510 34.83 52.24 .748
Cut edge to 72'' Any Quantity Per Foot
Nitrile – Asphalt
Æ
Æ
21
ServicePunching elevator bolt holes, per hole Heavy conveyor and 350 PVC Lightweight belt and PVC
Punching belt for lacing, per inch Including lacing customer’s belt Plus new belt lacing
Vulcanizing belts endless, in shop Per inch of belt width No charge for belt used in splice
Slitting customer’s belt, per foot Two cuts per pass Belt must be clean
$ .25 .20
1.00 Catalog
25.00
Manufacturer of Heavy Conveyor Belt
22
Standard Elevator Bucket Punching
5 x 4 P-1 2 3-3/16 9/32 1/4 6 x 4 P-1 2 4-3/8 9/32 1/4 6 x 5 P-1 2 4-3/8 9/32 1/4 7 x 4 P-2 3 2-11/16 9/32 1/4 8 x 4 P-2 3 3-1/16 9/32 1/4 9 x 4 P-2 3 3-5/8 9/32 1/4 7 x 4-1/2 P-2 3 2-11/16 9/32 1/4 7 x 5 P-2 3 2-11/16 9/32 1/4 8 x 5 P-2 3 3-1/16 9/32 1/4 9 x 5 P-2 3 3-5/8 9/32 1/410 x 5 P-2 3 4-1/8 9/32 1/4 10 x 5-1/2 P-2 3 4-1/8 9/32 1/4 8 x 6 P-2 3 3-1/16 9/32 1/4 9 x 6 P-2 3 3-5/8 9/32 1/410 x 6 P-2 3 4-1/8 9/32 1/410 x 7 P-2 3 4-1/8 9/32 1/411 x 5 P-3 4 3 9/32 1/412 x 5 P-3 4 3-3/8 9/32 1/411 x 6 P-3 4 3 9/32 1/412 x 6 P-3 4 3-3/8 9/32 1/411 x 7 P-3 4 3 11/32 5/1612 x 7 P-3 4 3-3/8 11/32 5/1614 x 5 P-4 5 3 9/32 1/414 x 6 P-4 5 3 9/32 1/415 x 6 P-4 5 3-1/4 9/32 1/414 x 7 P-4 5 3 11/32 5/16 15 x 7 P-4 5 3-1/4 11/32 5/1616 x 5 P-5 6 2-7/8 9/32 1/416 x 6 P-5 6 2-7/8 9/32 1/418 x 6 P-5 6 3-1/8 9/32 1/420 x 6 P-5 6 3-1/2 9/32 1/416 x 7 P-5 6 2-7/8 11/32 5/1618 x 7 P-5 6 3-1/8 11/32 5/1620 x 7 P-5 6 3-1/2 11/32 5/16 8 P-7 5 3 9/32 1/4 9 P-7 5 3 9/32 1/4 10 P-7 5 3-1/2 11/32 5/16 11 P-7 5 4 11/32 5/16 12 P-7 5 4-1/2 11/32 5/16 13 P-8 7 3-1/2 11/32 5/16 14 P-8 7 4 11/32 5/16 15 P-8 7 4 11/32 5/16 16 P-8 7 4-1/2 11/32 5/16 18 P-8 7 5 11/32 5/16 20 P-9 9 4 11/32 5/16
Bucket size is bucket opening
Bucket Size
Punch Style
No. of Holes
HoleCenters
Hole Bolt Size Size
0 0
P - 1 0 0 0
P - 2
0 0 0 0 0
P - 4 0 0 0 0 0 0
P - 5 0
0 0
0
0
P - 7 0
0 0
0
0
0
0
P - 8 0
0
0
0 0
0 0
0 0
P - 9
0 0 0 0
P - 3
1''
1''
1''
Material WeightsMaterial Lbs./Cu. Ft.
Wood Chips 20Coke 30Corn 45Rice 45Soybeans 45Wheat 50Coal 50Clay 75Bauxite 80Salt 95Limestone 95Cement 100Sand 100Granite 100Gravel 110Phosphate 110Slag 110Copper Ore 140Iron Ore 150
Any punching by customer pattern.
Punching�
�
Elevator Belt
Up chargeMultiplier
23
Bucket projection and the tug of bolts on the belt carcass are limiting factors in elevator belt service. Choose a carcass strong enough to hold the bolts, not tear the belt and drop the load.
Buckets handling large, lumpy materials are spaced close together and filled from a chute. Belt speeds are slower than with digging buckets.
Digging buckets are spaced apart, usually travel faster and throw the load at the top. Grain and light, free flowing material are handled in this way.
Special Belts Price will produce any elevator belt specification.If a belt under 24'' wide must be manufactured, an up-charge must be made because of trim. Many elevator belts may be supplied from stock belts shown in previous pages.
22'' 1.01520'' 1.03318'' 1.05616'' 1.08315'' 1.10114'' 1.11913'' 1.14112'' 1.16711'' 1.19710'' 1.233
Brushes .65 each
Good shelf life
¢
For easyvulcanizing and field repair work. No heavy equipment necessary.
Cold Bond
Splice Kits
24
ToolsPorcupineRoller2'' x 2''$ 126.30
SmoothRoller2'' x 2'' $ 34.09
“V” HookPly Knife $ 17.64
CleatSkiver$ 17.05
of thetrade
CorrugatedStitcher1/4'' x 2'' $ 22.73
for field vulcanizing
•Cement •Solvent•Tiegum •Fabricdip•Splinestrips •Allfreshfromfactoryproduction
Splice Kits are made to order from factory production lines Call (800) 633-1470 for price.
Coverage SC2000 Cement 30 sq. ft. 1 kg. (Quart) $ 64.97 Hardener (Qt.) 40 gr. $ 12.08
25
Examples: A 350 ft. C:C Conveyor on a 17-1/2 degree incline would have a total lift of 105.25 feet (3.5 x 30.07).
A 203 ft. C:C Conveyor on a 20 degree incline would have a total lift of 69.43 feet (2.03 x 34.20). or, a 69.43 lift on a C:C Conveyor 203 feet long would indicate an incline of 20 degrees (69.43/2.03), read from chart.
Calculating Lift from Degrees of Incline Calculating Belt Weight .375 lbs. per sq. ft. per 1/16'' thickness. Calculating Feet per Roll Feet = D2 - d2 15.3T D is outside diameter of roll (in inches). d is core diameter (in inches). T is belt thickness (in inches). Calculating Belt Thickness Cover Thickness + Carcass Gauge Belt Thickness Calculating Roll Diameter .325 √ T x L T is Belt Thickness (in inches) L is Belt Lengths (in feet)
Engineering
Conveyor Lift (feet) per 100' of Incline Conveyor length (C:C) 5 8.71 7-1/2 13.05 10 17.36 12-1/2 21.64 15 25.88 17-1/2 30.07 20 34.20 22-1/2 38.27 25 42.26 27-1/2 46.17 30 50.00 32-1/2 53.73 35 57.36
Something New!
26
• Windups
Price
Standard andCustom Designs
Engineered for a lifetime of service!
27
•
Standard and Custom Designs
Quality•Service•Durability
Made by the people who make the belt.
Slitters
Belt Master Equipment
Roll widths 60'' to 96'' Roll weights 20,000 to 30,000 lbs.
Price
28
Impact and Abrasion
The greatest wear on a belt usually occurs at the point of loading. The impact of large, heavy, jagged and sharp materials can cut and gouge the belt covers, particularly if covers are thin.
Limit the fall of material at loading. Load in direction of belt travel, and cush-ion the fall with baffle plates and cushion idlers to avoid scuffing. Use skirt board at point of loading to avoid spillage, trapping of material, and overloading. Continue the skirt board down the sides of the conveyor to limit spillage.
Lift gobbles horsepower
Typical Conveyor 500 ft. longwith 36'' belt 3 ply 330
Nothing moves materials like
Conveyor Belt
Over 45º AngleFree fall is top ofchute to top of belt
Under 45º AngleFree fall is bottom of chute to top of belt
45º
Baffle Plate –
Cushion Idlers
Return Rollers
100 lbs.Cuft
Lift Tons / hr. HP
20' 1321 55
40' 1321 81
60' 1321 107
80' 1321 134
100' 1321 160
35º Idlers a t 400 f t / min.
29
In the transition, the belt edge distance from troughing idlers to the face of the pulley is greater than the belt center distance. The edge must stretch slightly not to tear, while the belt center must compress slightly but not pucker or buckle. These differences are compromised by the length of the transition and by proper location of the troughed belt on the center line tangent.
Several adjustable troughing idlers are recommended between the last regular idler and the face of the pulley, to support the load and to limit spillage.
Rubber can outwear steel many times over. An extra 1/16'' of rubber in the belt cover can yield up to 25% longer belt life. More tons per Dollar!
The transition distances shown will accommodate virtually all rubber belt constructions, including steel cable belts. Most belts, properly installed, will give many years of –
Trouble – Free Service!
Trans i t i o n
30
Minimum pul ley diameters
Minimum width for t roughing (empty)
Maximum width for load support
Maximum bucket project ion
Fabric Carcass 80% 35º 100 lb. elevatorTension Idlers Material
AWT 10:1 Inches Inches Inches Inches
75 2/150 14 18 30 4 75 3/225 16 30 42 6
90 2/180 15 24 36 5
90 3/270 17 30 42 6
90 4/360 19 33 54 7
110 2/220 16 30 36 5
110 3/330 18 30 48 7
110 4/440 20 36 60
110 5/550 26 42 72
At las 10:1m200 2m 400 18 24 42m200 3m 600 30 36 60m200 4m 800 30 42 72 m200 5m 1000 48 48 72m250 2m 500 24 36 42
m250 3m 750 30 42 60
m250 4m 1000 36 48 72
m250 5m 1250 48 54 72
Æ
All figures consider belt car-cass only. Heavy covers may increase pulley diameters and load support widths.
Empty belts must ride the bot-tom rollers of troughing idlers to run true.
Loaded belts can be steered by canting one or more sets of idlers. The belt will move in the direction they are turned like bicycle handle bars.
Recommended take up travel is 2% of conveyor belt length.
Belts made to a minimum length must be made slightly long. This overage will be shipped, but invoice will not exceed 2%.
Price belts are made to width.They run true from the start!
Belt Carcass
31
1. The belt splice moves sideways on the system as it makes complete rounds, generally moving a constant distance off center, sometimes several inches up the troughing idlers. The belt was not squared when spliced, causing the splice section to move sideways. Re-splice the belt to make it straight. 2. The belt rides to one side of the conveyor, climbing the idlers and staying there. The conveyor idlers or pulleys are not properly installed... pulleys are not perpendicular to the system. Align the pulleys and idlers, one or more of which are askew or crooked to the belt centerline. 3. The belt spins on the drive pulley. Tighten the belt, lag the drive pulley or lighten the load. 4. The belt edges curl inward, forming a “pipe” on the top side of the conveyor. The belt is too tight, the load too heavy, or the transition not long enough. Loosen the belt. 5. The belt stretches more than 2%, and tends to become more narrow or “necked down”. Usually caused by tightening the belt to stop it from slipping on the drive pulley. Lag the pulley and loosen the belt... it is telling you that the load is too great, and you are straining the carcass. Or, use a belt with a stronger carcass. 6. The belt breaks. The load is too great for the carcass... lighten the load or use a heavier belt. 7. Belt fasteners pull out. The belt carcass is too light for the load or the fasteners were not properly installed. Re-lace carefully and/or use a heavier carcass belt. 8. The vulcanized splice peels apart. Improper vulcanizing job, due to incompatible raw materials, cured compounds, poor cements, or improper cooking time/temperature. 9. The belt settles into the bottom troughing idler junction, soon wearing a sag strip in the belt. The carcass is too light, the load is too heavy, and maybe the belt is pulled too tight and forced into the idler junction. Loosen the belt, use a heavier carcass, or use idlers with staggered or offset rollers that have no crevices between the rollers. 10. The belt drifts around on the conveyor system when empty or lightly loaded. The belt carcass is too heavy (stiff). The conveyor belt must trough completely against the idler rollers, or it cannot be controlled.
...know your Stuff! A conveyor belt does exactly what you make it do, no more and no less. It has no mind of its own. It is not wayward and it does not hate you! It is sympathetic and will tell you exactly what is wrong with your conveyor system. Pay attention!
31B
Hey ! Bookworm ! !Not all our people spend their time selling rubber.Here are 3 novels and a textbook written byJ. Gideon, available on Amazon to purchase for your kindle at 99¢ each.
Several evenings of entertainment here at a price any poor rubber peddler can afford !
(“Rags” is available in hard copy at $12.95 plus postage. Call Price Rubber sales (800) 633-1470 or (334) 277-5470.)
ASIN # ASIN # ASIN # ASIN # B007FH6L2C B007VU3216 B007JNJ9XK B007BSNJ16
32
Made from PRC 2 SBR stock for the severe service of clearing ice and snow from streets, highways, airport runways, taxi strips and parking lots. Tough, flexible and very wear resistant. Supplied in any width or length. It takes a scrubbing!
Stk. 22 (22SB) Standard 50' rolls. Works with authority !
60 duro2400 lb. tensile
Thick'' PIW 4'' 6'' 8'' 10'' 12'' 48''
$ $ $ $ $ $ $
Any Quant i ty Per Foot
Press cured
This tough, hard rubber blade will clean a belt while it runs. Gives long life without damage to the belt when used on either side.
Wiper Blades
Snow Plow Blades
Thick'' PIW 4'' 6'' 8'' 10'' 12'' 48''
3/4 1.166 4.67 7.00 9.33 11.67 14.00 55.99 1 1.555 6.22 9.33 12.44 15.55 18.66 74.66
1 1/2 2.333 9.33 14.00 18.66 23.33 28.00 111.98
Any width Any Quantity Per Foot
Stk. 80 50' rolls or cut to length.
1700 lb. tensile80 duro
#
$ $ $ $ $ $ $
1/4 .3881 1.55 2.33 3.11 3.88 4.66 18.63
3/8 .5822 2.33 3.49 4.66 5.82 6.99 27.95
1/2 .7764 3.11 4.66 6.21 7.76 9.32 37.26
3/4 1.1640 4.66 6.99 9.32 11.65 13.97 55.90
1 1.5530 6.21 9.32 12.42 15.53 18.63 74.53
Æ
33
Chute Lining Skirt Board
Thick'' PIW 4'' 6'' 8'' 10'' 12'' 48''
1/4 $ .3889 $ 1.56 $ 2.33 $ 3.11 $ 3.89 $ 4.67 $ 18.66
3/8 .5833 2.33 3.50 4.67 5.83 7.00 28.00
1/2 .7778 3.11 4.67 6.22 7.78 9.33 37.33
3/4 1.1660 4.67 7.00 9.33 11.67 14.00 55.99
1 1.5550 6.22 9.33 12.44 15.55 18.66 74.66
1 1/2 2.3330 9.33 14.00 18.66 23.33 28.00 111.98
Any width Any Quantity Per Foot
Nylonimpression
PRC #2 Grade belt cover stocks make this the finestproduct on the market, Press cured for uniform gauge and square corners. Produced in 48'' widths x continuous lengths, slit and cut to length.
(22SB) in constant production! 50' Rolls Std.
60 Duro 2400 lb. tensile
45ºBeveled if desired
PRC #2
MSHA Skirt Board Thick'' PIW 4'' 6'' 8'' 10'' 12'' 48''
1/4 .4872 1.95 2.92 3.90 4.87 5.85 23.39
3/8 .7311 2.92 4.39 5.85 7.31 8.77 35.09
1/2 .9747 3.90 5.85 7.80 9.75 11.70 46.78
3/4 1.4620 5.85 8.77 11.70 14.62 17.54 70.18 1 1.9490 7.80 11.70 15.59 19.49 23.39 93.57
Any width Any Quantity Per Foot
Our standard 33 SBR underground coal stock molded into skirt board, Nylon impression.
(33SB) 50' rolls or cut as specified
66 Duro1800 lb. tensile
$ $ $ $ $ $ $
Æ
Æ
34
400 º F Chlorobutyl
Skirt Board
Thick'' PIW 4'' 6'' 8'' 10'' 12'' 48''
$ $ $ $ $ $ $ 1/4 .7603 3.04 4.56 6.08 7.60 9.12 36.49 3/8 1.1410 4.56 6.84 9.12 11.40 13.69 54.74 1/2 1.5210 6.08 9.12 12.16 15.21 18.25 72.99 3/4 2.2810 9.12 13.69 18.25 22.81 27.37 109.48 1 3.0410 12.16 18.25 24.33 30.41 36.49 145.98 Any width Any Quant i ty Per Foot
No elastomer stands heat so well as stock 16, used on our most heat resistant conveyor belt. We mold that 16 stock into 48'' slabs, Nylon impression both sides, then slit to width and cut to length. Steel mills, sintering plants, taconite processors, and foundries all have a need for this premium product. Square edges every time.
Stk 16 (16SB) 50' rolls standard.65 duro.
1900 lb. tensile
Thick'' PIW 4'' 6'' 8'' 10'' 12'' 48''
$ $ $ $ $ $ $ 1/4 .4822 1.81 2.71 3.62 4.52 5.43 21.70 3/8 .6486 2.59 3.89 5.19 6.48 7.78 31.13 1/2 .8447 3.38 5.07 6.76 8.45 10.14 40.55 3/4 1.2340 4.95 7.42 9.90 12.37 14.85 59.40 1 1.6300 6.52 9.78 13.04 16.30 19.56 78.25 Any width Any Quant i ty Per Foot
60 Duro 2400 lb. tensile
Duck Back(22DB) Stk. 22 on 75 lb. Polyester
Chute Lining A ply of fabric with our standard chute lining makes mounting easier in hoppers and slope sheets. Greatly extends equipment life.
Æ
Æ
35
Economy Skir t Board
Sheet Rubber
(N60) Black Neoprene Sheet Plate finish 60 duro. Per Foot – Any quant i ty 1000 lb. tensile 350% elongation Oil resistant, for general gasket work. Temp. from –20º to 170º F
Thick'' 36'' 48''1/16 $ 2.59 3.52 1/8 5.20 6.89 3/16 8.63 11.39 1/4 10.43 13.93 3/8 16.75 22.37 1/2 22.42 30.25
Thick'' 36'' 48''
1/8 10.38 13.70
1/4 20.63 27.48
3/8 31.30 –– 1/2 37.42 ––
40 duro3400 lb. tensile600% elongationA pure gumfloating stock.
$ $
(R40) Tan Pure Gum Sheet Plate finish
Per Foot – Any quant i ty
(R75) Red Sheet Packing Fabric or Plate finish
75 duro. Per Foot – Any quant i ty600 lb. tensile
200% elongation
For cold water gasketing– –20º to 170º F
Thick'' 36'' 48'' 1/16 $ 2.84 $ 5.78
1/8 5.62 7.21 3/16 8.44 11.27 1/4 10.96 14.38
Thick'' 36'' 48'' 1/16 $ 4.07 $ 5.12 1/8 5.62 10.00 3/16 11.64 15.66 1/4 14.92 20.11
(E60) Black EPDM60 duro. Plate f inish.Resis ts chemicals , ozoneand aging. 900 lb . tensi le350% elongat ion.Per Foot – Any quant i ty
(R46) Black Corrugated Matting – 1/8'' std. rib max. roll – 35 yards Any quantity
For high traffic aisles in schools. churches and public buildings.
Width'' Per Ft. 24 $ 3.11 36 4.61 48 6.25
(R60E) A thrifty skirting for less abrasive applications. Helps control the load and limit spillage.
50' rolls only
50' Rolls only – Per Foot Thk.'' 4'' 6'' 8'' 10'' 12'' $ $ $ $ $ 3/8 1.01 1.48 1.97 2.47 2.96
1/2 1.32 1.97 2.63 3.28 3.95
3/4 1.97 2.96 3.95 4.95 5.92 60 Duro.
1 3.95 4.44 5.25 6.57 7.88 1000 lb. tensile
36
3'' Pin Loc US Pat. #4,477,202 With pin and clip.
Cast nodular iron journal will turn a square shaft with real authority. Shaft has keyway. Used throughout Price factories.
Size Capacity WT. Shaft (lbs.) (lbs.)
3'' 10,000 160 3'' x 29''
$ 859.00
To extend the life of sizing screens.
Size'' Foot 1/4 $
.87
3/8 1.10 1/2 1.56 50' / 100' coils
ROUND
FLAT HEX
65 duro
(R53)
CustomMade
Any size and shape to 60'' dia x 15' long Tan pure gum, SBR, EPDM, Neoprene, Viton, Nitrile. Prompt delivery from Memphis Call (800) 331-9360
Sleeves and Rollers
Channel
Epoxy / Wood Chip Cut with a saw 4'', 6'', or 8'' dia. with sq. holes Length
Hole 3'' 72'' 2 1/4'' $ 1.08 25.92 3 1/4'' 1.44 34.56 4 1/4'' 1.89 45.36
Belt Cores
Vulcanize
Cleat
37
6.50 9.75 12.99 19.49 .140
D103
FoodBelt
D102
FDA and USDA approved
-20º to 212º F
Odorless and Tasteless
Polyester Fabric Fabric Impression Top Carcass Covers PIW 12'' 18'' 24'' 36'' Ga.'' $ $ $ $ $ 3/105 3/64 x FS .5415 Any Width to 72'' Any Quantity Per Foot
White Mini – Rough Top
Nitrile
*Not FDA/USDA Approved.
Polyester Fabric Smooth Top Carcass Covers PIW 12'' 18'' 24'' 36'' Ga.'' $ $ $ $ $ 2/70 3/64 x FS .3147 3.78 5.66 7.55 11.33 .094 3/105 3/64 x FS .4613 5.54 8.30 11.07 16.61 .125 Any Width to 72'' Any Quantity Per Foot
Æ
Æ
Lightweight and P VC 4
4
4
4
4
4
Cut
Slit
Punch
LaceWe do it all
38
PRC grade #2 gives a lively, rubbery grip topackages on inclines to 37º. All-Polyesterfabrics slide easily on steel surfaces.
D240
Carcass Covers PIW 12'' 18'' 24'' 36'' Ga.'' 2/150 3/32 x FS $ $ $ $ $
Any width to 72'' Any Quantity Per Foot
This soft tan rubber top grips packages and cartons for incline conveying. Clean, non-marking and slides easily on tables and metal chutes.
Black or Tan Rubber
Carcass Covers PIW 12'' 18'' 24'' 36'' Ga.'' 120 3/32xSB .2157 2.59 3.88 5.18 7.77 .150 Any width to 72'' Any Quantity Per Foot
Especially useful if grease is present. The bare bottom slides easily on steel. Woven Polyester
Rough Top
.3951 4.74 7.11 9.48 14.22 .180
Stk. 95 on all Polyester Fabric. Carcass Covers PIW 12'' 18'' 24'' 36'' Ga'' $ $ $ $ $ 2/150 1/8xbare .2687 3.22 4.84 6.45 9.67 .211 1/8x1/32 – – – – – – 3/225 1/8xbare .4212 5.05 7.58 10.11 15.16 .254 1/8x1/32 – – – – – – Any width to 48'' Any Quantity Per Foot
$ $ $ $$
D106
D105
Æ
Æ
Æ
39
Carcass 3/32xFS PIW 12'' 18'' 24'' 36'' Ga.'' $ $ $ $ $ 2/150 Tan .4987 5.98 8.98 11.97 17.95 .188 2/150 Black .4827 5.79 8.69 11.58 17.38 .188
Any Width to 72'' Any Quantity Per Foot
Has asoft touch!
Made in USA
D104
Black or Tan Rubber
Cresceut TopEasy cleaning, long lasting.
D107
P o p u l a r a s a t u b e b e l t i n h a n d l i n g f e r t i l i z e r . C l e a n a n d n o n - c o r r o d i n g .
Incl ine Conveyor Bel t– most popular for handl ing fragi le products up incl ines to 37º . Polyester , bare back s l ides wel l .
Wedge Grip
Covers
Carcass 1 side PIW 12'' 18'' 24'' 36'' Ga''
120 Black .1543 1.85 2,78 3.70 5.55 .140
125 White .1968 2.36 3.54 4.72 7.08 .150
200 Black .2744 3.29 4.94 6.59 9.88 .170
Any Width to 72'' Any Quantity Per Foot
$ $ $ $ $
Æ
Æ
40
C115
C235
Transmission
Hot StockSaw Mill
Polyester carcass Carcass Covers PIW 12'' 18'' 24'' 36'' Ga.'' $ . $ $ $ $ 3/105 FS x FS .3150 3.78 5.66 7.55 11.33 .141 4/140 FS x FS .4307 5.17 7.75 10.34 15.50 .188 Any Width to 72'' Any Quantity Per Foot
Originally designed to replace leather belts for farm tractors and in general machine shops, this belt still serves in light conveying of saw dust, wood scraps, furniture and feed.
Suitable for handling raw rubber on the mill in processing. The 35 oz Silver Hard duck topgives tack free operation.
Still used on old saw mill drives where the carriage must reverse at the end of each stroke.
Carcass Covers PIW 12'' 18'' 24'' 36'' Ga.'' $ $ $ $ $ 3 ply bare x FS .3653 4.38 6.58 8.77 13.15 .141 4 ply bare x FS .4573 5.49 8.23 10.98 16.46 .188
Any Width to 72'' Any Quantity Per Foot
and Water Belt
Æ
Æ
Not FDA Approved
Black P VC Belting Polyvinylchloride on all-Polyester carcass.
D110
Popular where oil and grease are present such as auto assembly plants, machine shops, and steel rolling mills. The tough, woven Polyester carcass is fully impregnated with PVC for flex, strength and durability. Slider bed, too.
For light applications and slider bed service.
For heavy duty service, sharp and greasy products.
$ $ $ $ $
Carcass Covers PIW 12'' 18'' 24'' 30'' Ga.'' 120 Bare .1533 1.84 2.76 3.68 4.60 .125 150 Bare .1853 2.22 3.34 4.45 5.56 .156
120 Covers .1543 1.85 2.78 3.70 4.63 .141 150 One .2043 2.45 3.68 4.90 6.13 .172 200 Side .2744 3.29 4.94 6.59 8.23 .219
120 Covers .2044 2.45 3.68 4.91 6.13 .156 150 Both .2847 3.42 5.12 6.83 8.54 .203 200 Sides .3363 4.04 6.05 8.07 10.09 .250 350 .4449 5.34 8.01 10.68 13.35 .317 450 .5379 6.45 9.68 12.91 16.14 .354 Any width to 72'' Any Quantity Per Foot
PVC Cleats and V-guides. . . .bonded to your belt to suit your application.Call (800) 331-9360 (Memphis) for designhelp and quotation.
White or Black
1/2'' to 3'' high
O thru D
41
Æ
42
Wherever materials move
Flexco is hard at work!
Fastener Metals
Steel fasteners are made from Carbon Steel, suitable for most applications.Stainless Steel fasteners are made from type 316, providing extra resistance to abrasion, corrosion, acids and magnetic fields.MegAlloy (trademark of Flexible Steel Lacing Co.) fasteners are several times more resistant to wear and abrasion than steel. Not recommended for corrosive situations.Everdur (trademark of American Brass Co.) fasteners are made from an alloy of Copper and Silicon. They are spark-proof and non-magnetic; widely recommended for grain elevators, flour mills, and coal mines, where explosion is a constant hazard.
43
Heavy duty – not hinged.Universally acceptedfor all applications.Available in metals shown on page 49 90˚Templets
“E” box of 25 “C” bucket 100 sets 1, 140 1 1/4 2 1/4
Size Range’’
1 .188/.438 140 .188/.438 190 .313/.563 1 1/2 .438/.688 2 .563/.813 2 1/4 .563/1.188
2 1/2 .750/1.000 3 .934
$ $ $ $ $ $ $ Top + Bot 48 61
53 67
49 63
63 79 145 179
$ Top + Bot 196 250 218 274
203 257
257 326
595 –
$
E box of 10
(2) Bolt Hand Tools Cracking Power Tools Quick Break Punch Bore Bit Wrench Chisel Punch Bore Bit Wrench Socket �
24.94 17.13 26.33 18.17 87.44 16.41 26.33 25.27 24.94 17.13 26.33 18.17 87.44 16.11 26.33 24.81
28.10 20.75 27.09 24.28 87.44 23.13 26.84 29.87
Size For 1 1 140 190 1 1/2 2 2 2 1/4 2 1/2 3 3
$ $ $ $ $ $ $ $ $
� for Steel Nuts, 375x/550
Rip Repair Fasteners Box of 25 Size Range'' Steel SSRP1 .250/.500 71.83 261.01RP2 .375/.813 97.23 425.48
$ $
Tools
Rubber - Covered Five 6 plate panels per box Size Range'' Steel MegAlloy 140 .188/.438 94.49 113.37 190 .313/.563 95.84 115.01 2 .563/.813 117.51 ––
$ $ Skiver
$13.42
Plate Lacing
61.40
Steel Stainless� MegAlloy� Everdur� Steel MegAlloy� Lgth 190 1 1/2, 2 2 1/2, 3
25.85 –– –– 106.50 12 23.02 26.45 –– 30.87 199.85 128.18 127.23 18 23.02 26.45 –– 35.44 232.69 150.80 146.01 24 23.02 26.45 46.75 32.26 199.33 167.99 132.91 30 28.78 33.04 58.46 40.98 248.91 204.24 168.77 36 34.57 39.66 70.13 94.91 471.69 355.45 391.03 42 40.32 47.12 81.82 48 46.08 52.90 93.53 51.23 –– –– –– –– –– 60 63.35 66.13 116.90 53.83 –– –– –– –– –– 72 –– 79.36 140.28
�
44
Nylon Covered Steel Cable same as R5
Popular on equipment with small pulleys, the beveled plate edges and recessednuts avoid hangups. The 375 X is used with belts up to190 PIW carcass while 550 serves to 400 PIW. Thespark-free Everdur serves coal and grain applications.
Hinged Plate
Size 375 X 550 375 X 550 100' Range .250 – .406 .250 – .625 Curved coilLength Steel Stainless� Everdur� Steel Stainless� MegAlloy� Templet 1⁄4 dia.
12 25.92 –– –– –– –– –– 35.47 31.54 18 39.94 145.03 168.94 30.29 114.52 73.53 35.47 31.54 24 49.80 180.02 210.13 38.82 146.26 94.14 35.47 31.54 30 63.82 231.04 269.46 49.70 187.65 120.60 44.31 39.44 36 77.81 282.08 328.80 60.58 228.99 147.04 53.17 47.33 42 91.82 333.09 388.14 71.41 270.40 173.49 62.04 55.18 48 105.84 384.12 –– 82.29 311.78 199.95 70.90 63.09 60 147.24 –– –– 104.02 414.21 –– 88.65 78.85
$ $ $ $ $ $ $ $
$
$ $ $ $
$
$
Me t a
l s
� MegAlloy has steel nuts and bolts. MegAlloy top and bottom plates and bare stainless cable hinge pin. � Everdur is all spark-free copper and silicon alloy. Hinge pin is bronze cable, nylon covered. � Stainless is all stainless with nylon covered stainless cable hinge pins.
Flex-Loc A nylon strip that helps eliminateripple from distortion of metal lacing; helps seal belt ends from dirt and moisture.FL7C for 140 32.82 FL11C for 190 up
45.01 and 375 x / 550
100' boxes
100 / Box 375 X 550 375 X 550
Steel 28.38 31.32 21.81 21.81 Stainless 94.42 94.42 165.98 165.98 Everdur 104.26 104.26 70.24 70.24
Extra Bolts Nuts
Lacing Tools for 375 x / 550hinged lacing are the same asSize 1 Plate Lacing..
Tape
Per set with hinge pins
135.79
45
Widely used throughout industry, particularly in underground mining where high flexibility over small pulleys is essential.
R5S Rivet Set
67.84 $
18 14.56 74.46 75.03 21.37 –– 4.43 7.15 19.28 48.22 24 18.91 92.18 75.03 27.80 36.66 5.95 9.54 20.08 50.22 30 23.27 113.47 75.03 34.21 45.14 7.42 11.89 20.88 52.23 36 29.09 141.79 75.03 42.76 56.44 8.90 14.28 –– 54.23 42 33.44 163.07 150.06 49.18 64.86 10.37 16.68 –– 56.23 48 39.26 300.00 150.06 57.70 72.53 11.86 19.07 –– 58.21 54 43.62 –– 150.06 64.12 84.59 13.36 21.45 –– 60.21 60 49.45 253.11 150.06 72.66 95.91 14.83 23.83 –– –– 72 59.64 –– 150.06 87.63 115.65 17.79 28.59 –– ––
R5 R51⁄2 R6 Nylon Covered Self-setting Range .219'' - .438'' .313-.594 .406-.688 Hinge Pins Steel Rivets Strip Per set (2 strips) Set Set Steel Armored Belt Box Lgth.'' Steel Stainless MegAlloy Steel Steel Cable Cab le Thk.'' 100 250
$ $ $ $ $ $ $
$ $
$ $
For thin beltsover small pul-leys, R2 does afine job on foodand agriculturalapplications.
Uses R5 hinge pins and r ivets Size Pulley
2 5'' b e l t s t o 3 3 0 P I W
5 9'' b e l t s t o 4 5 0 P I W
51/2 12'' b e l t s t o 6 5 0 P I W
6 18'' b e l t s t o 8 0 0 P I W
.25''
Hinge pin retaining-washers - 50 pkg $ 5.00
.313
.375
.438
.531
.563
.656
.688
ThinRivetMin. Rivet
Applications
Rivet Hinged
R2 Range .125''-.375'' Strip Per set (2 strips)Lgth.'' Steel Stainless
12 6.60 18.20 18 10.03 30.37 24 13.03 39.47 30 16.04 48.59 36 20.07 60.74 42 23.07 69.82 48 27.08 81.98 60 34.10 103.22
46
FLEXCOBR6 A rivet lacing designed to butt-join belt ends and eliminate punching. The 6-Rivet design will hold belts to 400 lb. tensions over pulleys as small as 14'' diameter. Suitable for belts to 35º troughing, offered especially as an alternate to field vulcanizing. Supplied in strips which may be joined for wider belts.
$ 24'' strip 59.12 30'' strip 77.38 36'' strip 97.37
42'' strip 120.85
A mechanical splicethat will roll over anypulley 20'' diameter orlarger, 5/16'' to 1 1/4'' thk. belt. Special tip and tail platesare used with regular Flexcoplate fasteners. Steel SS
Tip and Tail Kit $111.06 $ 231.36 Templet set (3) $190.94
Wedlock! . . . easier than vulcanizing.
Aluminum applicationtool, complete as shown.
$1711.19 – 48''
Rivet Plate
47
Size Range S SS S SS S SS S SS S SS S S
00 .050-.063 19.94 37.57 29.89 56.36 39.87 75.15 49.79 93.95 59.77 112.72 69.73 79.71 1 .063-.094 19.52 39.30 29.27 58.94 39.03 78.61 48.78 98.25 58.53 117.90 68.28 78.04 7 .094-.141 18.68 44.60 28.01 66.91 37.38 89.22 46.71 111.50 56.05 133.79 65.39 74.74 15 .125-.156 19.52 50.06 29.27 75.07 39.03 100.11 48.78 125.12 58.53 150.18 68.28 78.04 20 .156-.188 22.86 67.95 34.27 101.92 45.69 135.90 57.12 169.87 68.54 203.84 79.96 91.39 25 .188-.250 22.86 70.50 34.27 105.76 45.69 141.01 57.12 176.26 68.54 211.51 79.96 91.39 27 .250-.281 22.02 79.28 33.04 118.93 44.05 158.54 55.05 198.19 66.05 237.83 77.06 88.07 35 .281-.313 28.22 123.88 42.34 185.85 56.46 247.81 70.57 309.74 68.28 354.90 98.80 112.90 45 .313-.378 27.41 142.24 41.11 213.33 54.84 284.45 68.52 355.57 82.23 426.68 95.94 109.65 55 .378-.438 36.98 –– 55.45 276.54 73.91 368.70 92.40 460.89 110.87 553.07 129.36 147.84
4 sets per box with hinge and guide pins 12'' 18'' 24'' 30'' 36'' 42'' 48''
$ $ $$ $ $ $$ $ $$
Alligator For medium duty non-troughing service. Install with a hammer. Plain steel or Stainless. See page 39 for extra hinge pins.
$ Size'' Each RSC-187-4 145.52 RSC-187-6 218.27
RSC187-12 436.53 RSC187-24 873.04
Designed for light-weight, high-strength belt over small pulleys. They operate smoothly over steel slider-beds or on troughed conveyors. All lacings have stainless steel staples.(4 sets / box with nylon covered steel cable pins) Size'' RS125 RS187 Range .125 - .188 .188 - .250 Min Pulley 3'' 4'' Box Steel SS Steel SS
12” 49.11 89.24 55.08 121.51 18” 73.69 133.86 82.65 182.26 24” 98.23 178.47 110.18 243.02 30” 122.82 223.11 137.74 303.79 36” 147.34 267.71 165.29 364.52 48’’ 199.90 363.38 224.14 494.91
$$$$
$
Stap l e The RSC-187-6 Tool installs 6'' of lacing per move across the belt. Handles both 125 and 187 lacing. Lacing Tool
48
Size Range Steel SS Steel SS 1D .063 - .094 22.50 30.63 –– –– 1 .125 - .156 22.88 31.97 –– –– 2 .156 - .188 21.92 39.69 22.65 33.99 3 .188 - .219 23.30 41.82 23.79 36.08 4 .219 - .250 24.18 43.44 24.69 37.11 4 1/2 .250 - .281 25.41 43.44 –– –– 5 .281 - .344 28.18 54.23 29.48 45.36 6 .344 - .375 32.01 60.87 33.74 51.61 7 .375 - .406 33.69 64.57 –– 53.17
Size'' Steel SS
.0534 35.57 48.06 .0650 44.24 49.95 .0790 44.49 58.74 .0930 49.95 64.22 .1090 55.63 69.92 .1250 61.37 75.63 .1560 75.63 88.47
$ $
Belt Cleaner An assembly made for easy installation.Urethane blade cleans the sticky off the belt, easy tension adjustment.
Extra Blades Lgth Each Lgth Each $ $ 16'' 156.59 46'' 491.37 22'' 221.39 52'' 566.64 28'' 286.18 58'' 642.56 34'' 350.99 64'' 712.76 40'' 415.78 70'' 782.96 Clipper
12/12'' sets per box
$ $ $ $
Carded Unibar pins pins no pins
For lightweightfood and trans-mission belts.Easy on and off.
Vise Lacer
4'' 54.47 7'' 78.98 10'' 110.84
$
Nylon Covered
Hinge Pins for Staple or Clipper 100' Box
V - belt fasteners V-belt 10 Sets Nails Fasteners Rocker Size per box 100 pkg. holder pin tool $ $ $ $ A312 166.46 –– 19.92 –– B437 221.48 13.48 45.72 25.54 C531 233.50 14.73 90.71 31.50 D750 415.32 14.44 –– –– 25 staples
Blade Length Belt 2'' Short 8'' Short $ $ 24’’ 22'' 614.93 16'' 534.74 30’’ 28'' 695.15 22'' 614.93 36'' 34'' 775.35 28'' 695.15 42'' 40'' 855.57 34'' 775.35 48'' 46'' 935.79 40'' 855.57 60'' 58'' 1096.20 52'' 1015.99 72'' 70'' 1256.61 64'' 1176.39
X
X
* PRICED AT TIME OF INQUIRY.EZPI
49
Fuel and Steam (H61) Tank Truck (H13) Fuel Oil
(H67) Hot Tar and Asphalt
(H71) Hot Air Blower (H82) Cement Discharge
For suction and discharge service with petroleum fuels. Nitrile tube and Neoprene cover give long life.
150 psi
Oil resistant tube and cover for suction and discharge 150 psi 350º F
For heating tank Used in dry truck and RR cement tanker cargoes. service to unload. 150 psi 75 psi 330º F 3/16'' tube
– Chlorobutyltube, spiral wire carcass.Where safety matters!
250 psi 450º F
Widely used for homedelivery. Nitrile tube and cover handle petroleum easily.
150 psi
ID'' Ft. 1 1/2 5.02 2 5.64 2 1/2 7.18 3 8.88 4 11.86
ID'' Ft. 2 16.15 3 20.22 4 31.33
Red or Black
$
$
$
$
ID'' Ft. 1/4 .88 3/8 1.02 1/2 1.42 3/4 2.22 1 2.97 1 1/4 4.57 1 1/2 3.40
ID'' Ft. 1/2 3.04 3/4 3.42 1 4.34 1 1/4 5.84 1 1/2 6.48 2 9.73
ID'' Ft. $ 2 6.10 3 8.37 4 12.57
ID'' Ft. $ 4 8.19
(P4) Steam Hose
50
Dredge Sleeves and
150 PSIworking pressure
Made fromthe same toughrubbers and fabrics as our big conveyor belts – built for severe service in handling abrasive materials. These sleeves provide flexibility between discharge pipes but resist collapse from pinching shut. Top grade adhesions deny ply separation while all-Polyester fabrics provide flexibility and strength.
Made or cut to length
(P7) Dredge Sleeves Stk. 22 on 110 lb . Polyester (D3) Chain Clamp
for large hoses, 6' chain $ 90.00 ea.$ $ $ $
As tough as they come!
Per Foot ID'' Ply 3/8'' tube 1/2'' tube 3/4'' tube 1'' tube
4.50 3 17.55 21.05 28.06 35.06 6.625 4 27.60 32.76 43.07 53.39 8.625 4 35.93 42.65 56.08 69.51 10.75 5 47.66 56.03 72.76 89.50 12.75 6 61.12 71.05 90.90 110.75 14 7 72.16 83.06 104.85 126.65 16 8 88.24 100.69 125.60 150.51 18 9 105.75 119.77 147.79 175.81 20 10 124.71 140.28 171.42 202.56
51
Stk. 22 on 110 lb. Polyester Per Foot ID’’ Ply 3/8'' tube 1/2'' tube 3/4'' tube 1'' tube
4.500 3 18.90 22.67 30.21 37.76 6.625 4 29.73 35.28 46.39 57.49 8.625 4 38.70 45.93 60.39 74.85 10.75 5 51.33 60.34 78.36 96.39 12.75 6 65.82 76.51 97.89 119.27 14 7 77.71 89.45 112.92 136.39 16 8 95.02 108.44 135.26 162.09 18 9 113.89 128.98 159.16 189.34 20 10 134.31 151.07 184.61 218.14
The spring steel wire in the carcass allows this hose to stand the severe suction service of constant dredging operations. Tough as a boot and made to last!
Made inUSA
$ $ $ $
(P72) Sand Suction Hose
150 lb. Standard Built-in Nipple Welded Flange
Subject to change in unstable steel market.
Bui l t - in Nipples and Flanges$ $
Nipple OD'' Each OD'' Each
4 4.5 386 9 310 5 5.5 411 10 354 6 6.625 471 11 364 8 8.625 576 13.5 479 10 10.75 768 16 773 12 12.75 864 19 869 14 14 1004 21 962 16 16 1166 23.5 1622 18 18 1275 25.125 1863
Standard 10' or 20' lengths,or made to order.
Sand Suction Hoses
52
(H28) Contractor’s Good
(H-89) Green PVC
Economy
Utility
A general purpose hose, popular in moderate to medium service. Two - ply carcass is reinforced with spring steel wire.
A very popular hose forgeneral industrial and contracting service. Entirely weather proof and easy to clean. Smooth boreand cover.
ID'' Ft. $ 1 1/4 2.94 1 1/2 3.24 2 3.32 2 1/2 5.27 3 5.45 4 7.51 5 14.63 6 16.43 8 27.36
Max. 100' coils
$
Water Suction and
We couple all hoses to suit the application. Choose couplings, foot- valves and strainers from coupling section.
A real workhorse of a hose for heavy service where the going is hard and steady.
Max ID'' Lgth.' Ft. $ 4 32' 10.09 5 30' 12.61 6 32' 15.14 8 30' 22.48 10 31' 30.98 12 30' 41.83 14 20' 54.24
(S110) Heavy Duty
The two-ply carcass is madefrom 110 lb. belt fabric over a hightensile spring steel wire. The SBR tube and cover give excellentresistance to abrasion andweather.
1/8'' tube1/16'' cover
ID'' Ft. 1 .85 1 1/4 .96 1 1/2 1.28 2 1.85 2 1/2 2.77 3 3.32 4 5.50 6 11.66 8 19.71
53
Discharge PVC
(H78) Blue contractors
Nitrile /PVC (H77) Black oil resistant
Rot andmildew proof.
PSI Ft. 70 .32 70 .36 65 .43 60 .79 60 .77 60 1.02 40 3.98 45 1.92 45 3.64 35 12.71 30 17.41 30 25.06 30 32.84
Tough rubber tubeand cover over a synthetic carcass.
Ready-mix plantsuse this hose to dropfrom scale houseto cement truck.
$ PSI Ft. ––– ––– 150 .86 150 1.01 150 1.33 150 2.17 125 2.76 ––– ––– 115 5.29 70 9.94
$ ID'' PSI Ft. 1 ––– ––– 1 1/2 200 2.12 2 200 2.35 2 1/2 175 3.45 3 175 3.72 4 150 4.89 5 ––– ––– 6 150 8.29 8 150 13.44 10 ––– ––– 12 ––– ––– 14 ––– ––– 16 ––– –––
$
DropHose
(R-35T)
Tan Gum Rubber Boots ID'' Foot 6 23.80
8 31.79 10 40.72 12 48.26 24 97.75 Any Quantity * 1/4'' wall Seamless construction
$
(H19) Heavy Duty
With a woven Polyester carcass, these “Lay flat” hoses serve well in general industry, construction, and agricultural applications. Weather proof.
Rolls up flat for easystorage.
Flexible and tear-resistant.
150 psi
PVC (H79) Red
higher pressure
ID'' Ft. $ 1 1/2 2.34 2 2.96 2 1/2 3.69 3 4.67 4 6.29 5 14.03 6 10.99 6 5/8 11.64 8 15.22 10 25.72 *12 48.19 * 150 max. psi
54
Air Hoses
(P21) PVC Air and Water
(H25) Blue Push-on Air Hose
Temp. -30º to 185ºF
Spiral-lay carcass grabs the fittings! 200 psi
Needs no clamps
Blended compounds, flexible and weather resistant – feels Red, Blue, like rubber. or Yellow 70º F
Toughyellow SBRpin-prickedcover resistsabrasion andweather. BlackSBR/Nitrile tubehandles oil mistfrom compressors. Long thestandard forheavy duty rockdrilling, this isindustry’s best.
ID'' Ft. PSI $ 1/2 2.42 600 3/4 2.53 600 1 3.05 600 1 1/4 3.85 600 1 1/2 4.50 600 2 5.48 600 2 1/2 9.51 450 3 10.54 450
ID'' Ft. PSI $ 1/4 .36 300 5/16 .48 300 3/8 .44 300 1/2 .55 300 5/8 .67 250 3/4 1.01 250 1 1.26 250
ID'' Ft. $ 1/4 .89 3/8 1.09 1/2 1.11
Max. 100' lgths.
We couple all hosesat a modest charge.
Under 1'' ID, $2 per end.
Over 1'' ID, $2 per inch of ID.
We supply the bands.
You pick the couplings.
3
3
3
3
(H35) Yellow Spiral Air Hose
(H36) Red Pneumatic Tool (from P23) These 3/4'' x 50' x 200 psilengths are coupled with 3/4'' Universal Quick Acting fittings and bands each end. $ 34.27 each
55
(P22) Black
(P23) Red
(H31) Sand Blast Highly abrasion resistant static conducting pure gum tube. 50' or 100' lengths. (D6)
150 psi
SpecialAir and Water
In a widerange of ID’sand workingpressures, thesehoses serveindustry every-where. Special EPDMcompoundsgive maximumweather re-sistance andlong life. Flexible andeasy handling,these hosesare availablein lengths to700 feet long. We chopand couplefor any job.
•Alsoavailable in black.
(H6) White Creamery
For dairy and creamery wash- down with plenty of hot water. 150 psi
(H3) White molded nozzle has 3/4'' metal mender molded in.
ID'' Ft. $ 3/4 1.60 nozzle ––
ID'' Ft. Cplg. $ $ 1/2 2.76 6.16 3/4 3.52 4.84 1 4.41 5.90 1 1/4 4.71 8.96 1 1/2 5.68 10.02
ID'' PSI Ft. $ 1/4 150 .29 • 1/4 200 .26 1/4 250 .39 1/4 300 .40 5/16 200 –– 5/16 300 .39 3/8 150 .41 • 3/8 200 .37 3/8 250 .41 3/8 300 .43 1/2 150 .67 • 1/2 200 .47 1/2 250 .54 1/2 300 .55 5/8 150 .72 5/8 200 .59 5/8 300 .69 • 3/4 150 .59 3/4 200 .68 3/4 250 .68 3/4 300 .80 • 1 150 .82 1 200 .85 •11/4 200 1.74•11/2 200 2.01 2 200 2.47
Each 1/4'' male $ 5.07 3/8'' male 5.45
1/4'' female 5.07 3/8'' female 5.45
1/4'' barb 5.57 3/8'' barb 5.57
1/4'' male 1.34 3/8'' male 2.23
1/4'' female 1.49 3/8'' female 2.46
1/4'' barb 1.75 3/8'' barb 1.75
Quick Disconnect
COUPLERS
PLUGS
56
(D30) Mill Hose NST or IPS Coupled Single Jacket
A woven Polyester jacket and flexible rubber tube make this a popular in- Cpld Aluminum Rocker Lug. plant hose for fire protection (D52P) Fog Nozzle and general wash down Polycarbonate with brass stem. service.
Common ThreadsNPT (National Pipe Tapered) same as IPT (Iron Pipe Thread), seal by cold flow of tapered threads. No washer is required.NST (National Standard Thread) same as NH (National Hose) are straight threads and use a washer to seal.NPSH (National Pipe Straight Hose) same as IPS (Iron Pipe Straight) are straight threads and use a washer to seal.These threads are not interchangeable and anadapter must be used for connecting threads.
250 psi test
(D59) Spanner(D59HW) Hydrant Wrench, ZincWrench, Adjustable plated. Handles (D51P) Polycarbonatemalleable iron head Pin-lug. cplgs. Nozzle NST or IPS.with 18'' steel handle. 1-1/2'' x 10'' x 1/2'' orifice.Fits all hydrant and $ 9.45hose couplings. $ 20.32
(D51) Polished Brass Nozzle
$ Size'' Lgth.'' Orifice Each 3/4 GHT 6 1/4 21.92 3/4 IPS 6 1/4 21.92 1 IPS 8 5/16 25.41 1 1/4 IPS 10 3/8 38.33 1 1/2 IPS 10 1/2 31.19 2 IPS 12 9/16 55.86 2 1/2 IPS 12 1 80.38 1 1/2 NST 10 1/2 31.19 2 1/2 NST 12 1 80.38
$ $ $ Size'' Foot 50' 100' 1 1/2 .89 71.29 116.04 2 1.16 65.40 123.40 2 1/2 1.61 132.74 213.24 3 1.91 110.76 206.26
Size'' x Thread Each 3/4 x GHT 16.67 3/4 x IPS or NST 25.80 1 x IPS or NST 24.73 1 1/2 x IPS or NST 14.31 2 1/2 x NST 92.66
$
*Cpld Short Shank D40 IPS
*
*
Fire Hoses
Size'' Each $ 2.84 1 1/2 2 2.97 2 1/2 3.54 3 4.95
57
and CouplingsMildew Proof
Size'' Jacket Per Ft. 50' Cpld. 1 1/2 Single 1.05 79.54 300 lb. 2 1/2 test 1.91 147.74 1 1/2 Single 1.10 82.04 500 lb. 2 1/2 test 1.98 151.24
1 1/2 Double 1.49 97.13 400 lb. 2 1/2 test 2.42 161.13 1 1/2 Double 1.61 105.63 600 lb. 2 1/2 test 2.70 175.13
$ $
(D56)Pin LugAdaptersCast Brass Female x Male Each 1 1/2 NST 1 1/2 IPS 21.39 1 1/2 IPS 1 1/2 NST 17.06 2 1/2 NST 1 1/2 IPS 15.59 2 1/2 NST 1 1/2 NST 15.59 2 1/2 NST 2 1/2 IPS 36.67 2 1/2 IPS 2 1/2 NST 38.25 3 IPS 2 1/2 NST 38.93
$
(D67) HexAdaptersTurned Brass
$
$ $
(D54) Fire Hose CouplingsAluminumRocker Lug
Specify threadNST or IPS
Size'' Set Washer1 1/2 27.04 1.052 1/2 52.24 1.65
(D64) Hydrant Adapter Brass Pin Lug 2 1/2'' NST x 3/4'' x GHT or IPT $ 15.41
$
(D66) HexAdapters Turned Brass
Male x Male Each 1 1/2 IPT 1 1/2 IPS 10.551 1/2 IPT 1 1/2 NST 9.66 1 1/2 IPT 2 1/2 NST 33.08 2 IPT 1 1/2 IPS 24.15 2 IPT 1 1/2 NST 18.77 2 IPT 2 1/2 IPS 33.21 2 IPT 2 1/2 NST 25.78 2 1/2 IPT 2 1/2 IPS 27.33 2 1/2 IPT 2 1/2 NST 27.33 3 IPT 2 1/2 NST 51.98
ColorsRedOrangeBlueTanYellowGreenBlack
For industrial fire protection.Long-life rubber tube and syntheticyarns. Coupled with AluminumRocker Lug, NST. UL label availablefor .35 per ft. May be color coded (dyed) for plant identification.
1 1/2'' .282 1/2'' .40per foot.
Female x Male Each1 1/2 IPT 1 1/2 NST 10.50 1 1/2 NST 1 1/2 IPT 8.93 2 1/2 NST 3/4 IPT 73.66 2 1/2 NST 1 IPT 70.35 2 1/2 NST 1 1/2 IPT 40.79 2 1/2 NST 2 IPT 26.51 2 1/2 NST 2 1/2 IPT 25.86 2 1/2 NST 3 IPT 45.75 3 IPT 2 1/2 NST 43.84
(D85) UL Grade Fire Hose - Gold
58
Food Hoses ID'' PSI Ft. $ 1 150 –– 2 150 4.65 3 150 13.73 4 150 17.99 5 75 27.00 6 75 31.81
Green (H42) FDA Food Hose EPDM cover Meets allFDA require- Whitements for odorless andfood service tasteless natural-30º to 185º F rubber tube. For suction and discharge.
Clear PVC food hoses for handling all food. They meet all sanitary standards.
Temp 4º to 150º F
For vacuum or discharge (H8) (H9) (H10) Smooth cover static wire These see-through hoses Used forhandle all Poultryfoods in Meataccordance with Milkall regulations Wineof Beer 3-A general FDA Canning USDA Clear Clean and PVC Clear Hoses
and bore H8 ID'' PSI Ft. $ 3/4 115 1.76 1 100 1.76 1 1/4 90 2.21 1 1/2 85 2.46 2 85 4.06 2 1/4 –– –– 2 1/2 65 5.32 3 55 7.13 3 1/2 55 –– 4 50 12.19 5 40 15.57 6 30 23.30 8 25 38.58
Smooth bore H9 H10 ID'' PSI Ft. Ft. $ $ 3/4 –– –– –– 1 55 1.56 –– 1 1/4 50 1.85 3.92 1 1/2 50 2.19 4.08 2 40 2.97 5.62 2 1/4 40 4.30 6.33 2 1/2 40 4.58 6.80 3 40 5.89 9.05 3 1/2 35 9.97 13.72 4 35 10.24 14.80 5 30 17.21 23.29 6 30 19.60 25.81 8 20 30.02 ––
59
Vacuum
ID'' H53 H57 H58 H58Y 1 1/2 2.05 1.37 –– 3.64 2 2.16 1.84 4.96 4.14 2 1/4 2.37 2.52 –– –– 2 1/2 2.58 2.59 5.50 4.72 3 2.81 2.78 5.72 5.30 3 1/2 3.33 3.09 –– –– 4 3.74 3.16 6.55 6.19 4 1/2 3.73 3.61 –– –– 5 3.74 3.64 7.64 8.50 6 4.29 3.71 8.20 8.74 7 4.80 4.70 10.07 11.39 8 5.33 5.18 10.62 12.64 10 6.82 7.37 15.23 –– 12 8.06 8.08 16.79 –– 14 10.63 9.41 21.14 ––
Heavy Duty - Yellow Urethane coated
Heavy Duty - Black Urethane coated
Industrial - Blue PVC coated
Lightweight - Black Neoprene coated
Per Foot
(clear with yellow helix)
Used for blowing and venting air, dust, fumes and vapors. Hoses have a spring steel wire, covered with fabric or coated for different uses.
(H60) Grey Utility Vacuum for portable machines
Max 25' lgth. -60º to 180º F
(H16) Clear NSF beverage tubing for all potable services.
(H16R) Reinforced NSF beverage tubing for low pressure.
$ $$$
ID'' Wall'' H16 H16R 1/8 1/16 .09 –– 1/4 1/16 .15 –– 1/4 1/8 .36 .34 3/8 1/16 .20 –– 3/8 1/8 .51 .50 1/2 1/16 .26 –– 1/2 1/8 .56 .64 5/8 1/8 .67 .89 3/4 1/8 .78 1.08 1 1/8 1.01 1.64 1 1/4 1/8 1.24 2.78 1 1/2 1/4 3.06 3.48 2 1/4 4.06 5.20
$$
F o o t
ID'' Ft. Cuff $ 1.36 $ 2.39 1 1/2 2 2.28 3.48
25'coils
Vacuum and Vent Hoses
60
Chemical
Spray
(H44) UHMW Blue EPDM (H65) XLPE Green EPDM Chemical hose has high Chemical hose with cross- molecular weight cross- linked polyethylene tube linked polyethylene tube. will handle 90% of corrosive chemicals.
Thishose will 240 psihandle 98%of industrial chemicals. 240 psi
(H41) Paint Spray (M18) PVC Spray Hose
Excellent Yellow ribbed pin-prickedfor lacquers, Static cover vents vapors ofpaints and Conducting agricultural chemicals. solvents. Not Not for petroleumfor hot paints. based 600 Max. temp. 125º F chemicals psiworking pressure 175 psi at 70º F (D41L) Steel Long Shank
(D43) Male IPT Spray Brass Inserts Hose (D41S) GHT Short Shank Cast Brass
ID'' Ft. $ 1 1/2 2 2 1/2 3 4
ID'' Ft. $ 1/4 .87 3/8 1.28 1/2 1.87
ID'' Ft. $ 3/8 .62 1/2 .86
Hose'' x Thd.'' Each Hose'' x Thd.'' Each $ $ 1/4 x 1/8 .99 1/2 x 1/2 2.49 1/4 x 1/4 1.07 1/2 x 3/4 3.77 1/4 x 3/8 1.62 5/8 x 1/2 2.74 5/16 x 1/4 1.25 3/4 x 1/2 3.22 3/8 x 3/8 1.64 3/4 x 3/4 3.45 1/2 x 3/8 1.66 1 x 3/4 4.69
Size Set $ 3/8 x 3/4 6.19 1/2 x 3/4 6.94 5/8 x 3/4 6.32 3/4 x 3/4 7.37
Size GHT $ 3/8 x 3/4 15.67 1/2 x 3/4 13.55 5/8 x 3/4 12.29
Size IPT $ 1 20.90 1 1/4 27.56 1 1/2 28.04 2 39.72
8.81 9.7716.4619.0327.86
ID'' Ft. 1 $ 6.60 1 1/2 8.17 2 8.86 3 15.47
61
Water
Strainers and Foot Valves Plated Steel IPT Red iron IPT
$ $ $
$
(D31) Double Bolt ClampsMalleable ironCadmium Plated
Nipples(D89) Spiral andClamp Menders Plated Steel (D41) (D45) IPT Plated
for left hand convolutions
We couple all hoses
(D40) Short Shank Heavy aluminum casting with Brass nuts - IPS Size'' Set Washer $ $ 1 1/2 4.91 .27 2 7.39 .31 2 1/2 13.68 .57 3 15.26 .48 4 26.34 .75 5 –– –– 6 65.26 2.14 8 –– –– 10 –– ––
(D11) Strainer
(D14) Foot Valve
Leather
8'' Rubber Only
ID'' Each $ 1 1/2 2.54 2 2.89 2 1/4 3.15 2 1/2 3.34 3 3.65 3 1/2 4.13 4 4.52 5 5.68 6 7.51 8 10.18 10 11.45 12 16.06
Size'' Nip. Mend. $ $ 1/2 1.40 1.18 3/4 1.44 1.40 1 1.71 1.57 1 1/4 2.23 2.26 1 1/2 2.19 3.00 2 3.38 3.71 2 1/2 6.33 5.89 3 7.87 8.20 4 11.95 12.75 5 28.66 68.25 6 35.52 36.73 8 71.04 77.50 10 125.13 176.88
No. Range'' Each
400 3.50-4.00 6.94 463 4.06-4.63 7.10 525 4.69-5.25 9.36 550 5.00-5.50 9.36 600 5.31-6.06 10.57 675 6.13-6.88 11.71 769 6.94-7.63 14.21 818 7.69-8.19 20.11 875 8.25-8.88 20.99 988 8.94-9.88 22.45 1125 9.94-11.38 38.59 1275 11.44-13.00 44.40 1450 13.06-15.00 62.35 1700 15.06-17.25 77.91
Size'' Dia. Strainer Lbs. Ft. Valve Leather 1 1/2 5 9.61 2.75 17.09 3.49 2 6 11.14 5.25 25.12 5.57 2 1/2 6 11.95 7.50 32.08 6.83 3 7 16.31 11.25 40.71 10.32 4 7 18.33 11.25 67.54 16.14 6 9 53.68 47.00 161.62 34.52 8 11 1/4 92.03 100.00 370.73 65.13
62
Female Ground Male Size'' Joint Stem Bolts Range'' Each
1/2 10.09 2.42 2 1.06 - 1.19 1.783/4 14.45 4.52 2 1.31 - 1.50 2.81 1 15.26 6.38 4 1.69 - 1.94 5.73
1 1/4 23.98 6.62 4 1.78 - 2.09 8.15 1 1/2 24.86 8.40 4 2.25 - 2.56 8.40
2 34.31 12.19 4 2.50 - 2.78 11.10 2 1/2 72.23 21.64 4 3.06 - 3.50 26.64 3 85.98 27.05 4 3.81 - 4.06 29.87 Malleable iron, Cadmium plated
$ $ $
For high pressure service with air, water or steam, Boss isthe standard.
Handles Steam to 450º F.
3/4'' Triple Connector $ 4.94 ea.
These Malleable Iron, Cadmium plated air tool couplings are standard in the industry.
(D16) Universal Quick Acting Couplings
$ $ $ $ $
The Industry Standard
High PressureBoss Couplings
(D34) (D36)
(D37) Boss Clamps
NitrileSize'' Hose End Fem. Adapt. Male Adapt. Clamp Gasket
3/8 1.76 2.17 2.17 1.78 .24 1/2 1.76 2.17 2.17 1.78 .24 3/4 2.02 2.17 2.17 2.81 .24 1 2.55 2.48 2.54 5.73 .24 1 1/4 7.10 6.66 –– 8.15 .73 1 1/2 7.91 6.66 –– 8.40 .73 2 9.25 7.91 –– 11.10 .73
(D1) QC – For Agriculture, Petroleum, Chemical, and General Industry.
Aluminu
m
Aluminu
m
Aluminu
m30
4
Stainle
ss30
4
Stainle
ss30
4
Stainle
ss
Polypro
pylen
e
Polypro
pylen
e
Polypro
pylen
e
Aluminu
m30
4
Stainle
ss
Polypro
pylen
e
Nitrile
Gasket
Size''3/4 2.13 5.30 1.29 4.79 10.29 4.27 3.54 8.26 4.27 4.99 9.27 4.42 .39
1 2.63 6.85 1.59 5.61 14.34 4.57 4.80 11.29 4.67 5.61 12.17 4.94 .39 1 1/4 3.54 9.93 2.33 6.80 20.67 6.49 11.57 16.36 6.41 7.67 17.90 6.85 .43 1 1/2 2.67 12.32 2.43 6.55 24.39 7.00 6.49 19.68 7.00 7.04 21.17 7.59 .43 2 3.23 13.49 2.92 8.26 23.76 8.40 8.10 26.03 8.48 8.88 25.83 8.69 .43 2 1/2 6.09 24.02 –– 12.18 32.82 –– 11.24 36.46 –– 12.97 36.46 –– .56 3 5.78 26.54 5.17 13.10 46.41 12.90 13.60 50.54 13.05 13.10 49.09 13.65 .57 4 9.83 49.09 11.44 16.75 67.39 22.11 20.28 75.82 22.88 19.52 73.71 23.94 1.06 6 22.80 101.79 –– 40.30 145.43 –– 50.32 164.97 –– 44.81 148.82 –– 2.02
Size'' 3/4 2.25 4.81 1.50 2.79 6.18 1.50 4.25 7.20 4.27 2.56 2.85 1.40 1.90 1 2.63 7.41 1.76 3.32 8.46 1.65 5.15 9.93 4.37 2.50 4.28 1.51 2.12 1 1/4 4.08 1 0.88 2.52 4.08 12.85 2.35 7.79 13.69 6.12 3.22 7.44 1.73 2.90 1 1/2 3.15 13.69 2.50 3.42 15.65 2.50 5.85 16.25 6.34 2.25 8.09 1.84 2.90 2 4.05 21.24 2.71 4.46 20.39 2.70 7.07 18.95 8.18 2.84 13.16 2.47 2.90 2 1/2 6.84 29.84 –– 8.10 30.97 –– 9.51 29.18 –– 5.82 19.76 –– 2.90 3 8.57 41.63 5.25 8.57 41.42 5.76 11.01 37.27 12.02 4.75 23.73 4.50 4.35 4 12.74 65.29 10.40 13.21 72.12 10.40 15.33 51.25 19.68 8.01 38.61 7.80 4.35 6 37.74 147.42 –– 33.39 156.55 –– 36.17 119.34 –– 19.49 107.41 –– 16.85
Aluminu
m
Aluminu
m
Aluminu
m30
4
Stainle
ss30
4
Stainle
ss30
4
Stainle
ss
Polypro
pylen
e
Polypro
pylen
e
Polypro
pylen
e
Aluminu
m30
4
Stainle
ss
Polypro
pylen
eHan
dle
$ $ $ $ $ $ $ $ $ $ $ $
$ $ $ $ $ $ $ $ $ $ $ $ $
A B C D
E F DC DP
$
63
Quick Cam
Banding
64
(D29) Worm Gear Clamps
No. Range'' Box .10 6 .44-.78 .77 8 .50-.91 .77 10 .56-1.06 .77 12 .69-1.25 .79 16 .81-1.50 .79 20 .81-1.75 .79 24 1.06-2.00 .79 28 1.31-2.25 .82 32 1.56-2.50 .82 36 1.81-2.75 .84 40 2.06-3.00 1.02 44 2.31-3.25 1.13 48 2.56-3.50 1.13 52 2.81-3.75 1.21 56 3.06-4.00 1.21 60 3.31-4.25 1.26 64 3.56-4.50 1.26 72 1.88-5.00 1.37 80 2.50-5.50 1.58 88 3.12-6.00 1.64 96 3.62-6.50 1.66 104 4.12-7.00 1.68 128 5.62-8.50 2.50 152 7.12-10.00 2.68 188 9.37-12.25 2.94 200 10.13-13.0 –– 212 10.88-13.75 3.00 224 11.62-14.50 –– 236 12.38-15.25 –– 248 13.13-16.0 3.78 312 17.13-20.0 4.62
$
$ $ $ $
$ $
Width'' SS Galv. SS Galv. 3/8 36.75 16.80 51.98 26.33 1/2 49.88 25.20 71.77 33.08 5/8 68.25 27.83 97.34 39.90 3/4 86.63 19.70 122.38 47.25
No. ID'' Width'' SS Galv. Box of 100
Widely used to secure couplings, either crimp or punch lock, galvanized or stainless. Punch-loc Tool
(D22) Buckles (D23) Bands Box of 100 Box of 100'
(P20) $ 107.94
(D24) Preformed Bands
Preformed
Bands
(D20) Banding Tool
$ 81.86
(D21) Adapter $ 72.98
$ $
$ $
*3/4'' Galvanized Buckles are 50 to Box!
3 13/16 3/8 81.00 49.88
311 1 3/8 3/8 92.00 52.50 4 1 5/8 107.63 55.13 5 1 1/4 5/8 115.50 57.75 6 1 1/2 5/8 123.38 63.00 7 1 3/4 5/8 133.88 68.25 8 2 5/8 141.75 70.88 9 2 1/4 5/8 149.63 73.50
Box of 50 10 2 1/2 5/8 81.38 43.31 11 2 3/4 5/8 85.31 44.63 12 3 5/8 40.56 47.25 14 3 1/2 5/8 99.75 51.19
Box of 25
16 4 5/8 55.78 28.88 18 4 1/2 5/8 60.38 31.50 20 5 5/8 64.97 32.16 24 6 5/8 74.16 38.06
www.pricerubber.com
Warehouse2556 South 2570 West
West Valley City, UT 84119Watts (888) 597-7423 FAX (801) 956-0117
Mixing Plant3805 Morrow St.
Guntersville, AL 35976Watts (800) 633-2284FAX (256) 582-0847
Warehouse901 E. Kennedale PkwyKennedale, TX 76060Watts (800) 821-0668 FAX (817) 478-0360
Warehouse2953 Fleetbrook Dr.Memphis, TN 38116
Watts (800) 331-9360 FAX (901) 332-9366
Home Office / Factory2733 Gunter Park Dr. W.Montgomery, AL 36109Watts (800) 633-1470 FAX (334) 271-3194
•
••
•
•
Manufacturing Distributors of Industrial Rubber ProductsPrice