1982 - 2007
25Y E A R S O FEXCELLENCE
Spromak ltd 11G WILSON ROAD, HUYTON, LIVERPOOL L36 6AN ENGLAND TEL 0151-480 0592 FAX 0151-480 0656
E-MAIL [email protected] WEBSITE www.spromak.co.uk
MANUFACTURERS OFFLANGED BUTTWELD OUTLET®
FLANGED NIPPLE OUTLET®
FLANGED LATERAL OUTLET®
FLANGED ELBOW OUTLET®
FLANGED INSERT OUTLET®
BUTTWELD OUTLETS®
SOCKETWELD OUTLETS®
THREADED OUTLETS®
NIPPLE OUTLETS®
LATERAL OUTLETS®
ELBOW OUTLETS®
INSERT BRANCH OUTLETS®
Spromak ltdMANUFACTURERS OF
FLANGED BUTTWELD OUTLET®
FLANGED NIPPLE OUTLET®
FLANGED LATERAL OUTLET®
FLANGED ELBOW OUTLET®
FLANGED INSERT OUTLET®
BUTTWELD OUTLETS®
SOCKETWELD OUTLETS®
THREADED OUTLETS®
NIPPLE OUTLETS®
LATERAL OUTLETS®
ELBOW OUTLETS®
INSERT BRANCH OUTLETS®
Spromak ltd 11G WILSON ROAD, HUYTON, LIVERPOOL L36 6AN ENGLAND TEL 0151-480 0592 FAX 0151-480 0656
E-MAIL [email protected] WEBSITE www.spromak.co.uk
1982 - 2007
25Y E A R S O FEXCELLENCE
Spromak Ltd® introduce their range of reinforced branch outlet fittings for pipe line pressure vessel applications. BUTTWELDOUTLET, NIPPLE OUTLET, SOCKETWELD OUTLET, LATERAL OUTLET and THREADED OUTLET are designed to give integral reinforcement, added flow characteristics and stress distribution.
The company manufactures its forged steel branch outlet fittings from 1/4in. nominal bore upwards, to make full size and reduced size connections. They are produced as: BUTTWELD OUTLETS, SOCKETWELD OUTLETS, THREADED OUTLETS, NIPPLE OUTLETS and LATERAL OUTLETS. Full test data and proof calculations are available on request. These fittings are designed to meet design requirements of reinforced branch connections to the following soecifications: ASME B31.1 USA Standard Code for power piping.ASME B16.9 USA Standard for steel buttwelding fittings PD.5500 British Standard specification for fusion welded pressure vessels.ASME Boiler and pressure vessel codes section I and section VIII Div. 1 and 2.ASME B31.3 USA Standard Code for process piping, chemical plant and petroleum refinery piping.
BUTTWELD OUTLETS, SOCKETWELD OUTLETS, THREADED OUTLETS are manufactured by SPROMAK LIMITED® in its modern and fully equipped factory at Liverpool. The company offers full design facilities and expert advice on any aspect of reinforced branch connections.Inspection by the quality control department ensures the high standard of manufacture in day to day production is maintained. All fittings are fully certified and identified numerically.
For any additional information, quotations, or advice, contact: SPROMAK LIMITED®, 11G Wilson Road, Huyton, Liverpool L36 6AN, England. Telephone: 0151-480 0592. Fax: 0151-480 0656. E-Mail: [email protected] Website: www.spromak.co.uk
2
Some examples of Proof Burst Tests
CERTIFICATE OF APPROVAL
This is to cer fy that the Quality Management System of:
Spromak Ltd Liverpool
United Kingdomhas been approved by Lloyd’s Register Quality Assurance to the following Quality Management System Standards:
ISO 9001:2008
The Quality Management System is applicable to:
Production of branch outlet pipe fittings using materials in accordance with PED 97/23/EC Annex 1 section 4.3.
Approval Original Approval:3 October 1990
Certificate No: LRQ 0870517
Current Certificate:2 October 2009
Certificate Expiry: 30 September 2011
Issued by: Lloyd’s Register Quality Assurance Limited
This document is subject to the provision on the reverse 71 Fenchurch Street, London EC3M 4BS United Kingdom. Registra on number 1879370
This approval is carried out in accordance with the LRQA assessment and cer fica on procedures and monitored by LRQA. The use ol the UKAS Accredita on Mark indicates Accredita on in respect of those ac vi es covered by the Accredita on Cer ficate Number 001
Macro Revision 13
Issued by:Issued byssued by: Lloyd’s Registeteteteteteteeeteeteeteeeeteeteeeteeteeteetetteetttetettttttetteetetteettettttt r QuLloyd’s Registtttttttttttttttttttttttttloyd’s ReRegistttttttttttttttteeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeer Qeeeeeeeeeeeeeeeeeeeeeeeeeeeeeer Qu
QUALITY ASSURANCE
As a Company ever looking to improve on their Quality Standards, Spromak, were in October 1990 accredited with the Lloyd’s Register Quality Assurance Certificate to BS5750 Part 2 and ISO 9002.In keeping with this philosophy our latest certificate, shown below, is a testament of our commitment to this process.
3
OUTLET SIZE
RUN-PIPE SIZES
1/2
3/4
1
1¼
1½
2
2½
3
3½
4
RUN-PIPE SIZES
4
BUTTWELD-OUTLETS STANDARD AND EXTRA STRONG SOCKET-OUTLETS & THREADED-OUTLETS 3000 LBS.
Outlet over 4” order to specific run-pipe size BUTTWELD-OUTLETS SCH. 160 AND XXS
Outlets over 2” order to specific run-pipe sizeSOCKETWELD-OUTLETS & THREADED-OUTLETS 6000 LBS.
1/2
3/4
1
1¼
1½
2
2½
3
3½
4
3/4
1
1¼
1½
2
2 ½
3
3½
4
5
1
1½ - 1¼
1½
2
2½
3
3½
4
5
6
1½ - 1¼
2½-2
2
2½
3
3½
4
5
6
8
2½-2
5-3
2½
3½-3
4-3½
4
5
6
8
10
8-3
12-6
3½-3
5-4
6-5
5
6
8
10
14-12
36-10
36-14
5-4
8-6
12-8
6
8
10
14-12
20-16
10-6
18-10
24-14
10-8
12-10
14-12
20-16
36-24
36-12
36-20
36-26
18-12
18-14
20-16
36-24
36-20
36-20
36-24
1/2
3/4
1
1¼
1½
2
1/2
1-3/4
1
1½-1¼
1½
2
1¼-3/4
2-1¼
2½-1¼
2½-2
2½-2
2½
36-1½
6-2½
10-3
10-3
3½-3
3½-3
36-8
36-12
36-12
8-4
5-4
20-10
8-6
36-24
18-10 36-20
1/2
3/4
1
1¼
1½
2
1-3/4
1
1¼-1½
1½
2
2½
2-1¼
2½-1¼
2½-2
2½-2
2½
3
6-2½
10-3
10-3
3½-3
3½-3
4
36-8
36-12
36-12
8-4
5-4
5
20-10
8-6
6
36-24
18-10
10-8
36-20
20-12 36-24
OUTLET SIZE
OUTLET SIZE RUN-PIPE SIZES
Dimensions UnificationIn order to reduce warehouse inventory, ouroutlets have been unified to fit on differentrun-pipe sizes with gap maximum of 1/32”between the run-pipe and outlet. This doesnot cause any problems during welding.
OUTLET SIZEREDUCED SIZES
FULL SIZES
FULL SIZES
5
Buttweld Outlets • STANDARD
1/23/41
1¼1½2
2½3
3½456810121416182024263036
19.0022.0027.0032.0033.0038.0041.0044.0048.0051.0057.0078.0099.0094.00103.00100.00106.00111.00119.00140.00165.00181.00212.50
24.0030.0036.5044.5051.0065.0076.1593.50112.60120.50141.30170.00220.00265.00316.00351.00403.00456.00510.00610.00660.00762.00914.00
0.090.140.210.410.500.801.181.902.553.004.7510.5017.0021.0028.0032.0046.5059.0072.00142.00168.00218.00404.00
190022.0027.0030.0032.0038.0041.0044.0051.0051.0057.0078.0099.0089.00100.00105.00113.00119.00127.00140.00165.00181.00212.00
13.9018.9024.3032.8038.1049.3059.0073.7085.4097.20122.30146.30194.00247.50298.00330.00381.00432.00482.50584.20635.00738.00889.00
0.070.110.180.320.410.751.151.902.303.504.326.8014.6021.0028.0034.5052.5059.0085.00146.00182.00255.00446.00
A C ApproxWeight A D Approx
Weight
1/23/41
1¼1½2
2½3
3½456810121416182024263036
19.0022.0027.0032.0033.0038.0041.0044.0048.0051.0057.0060.0070.0078.0086.0089.0094.0097.00102.00116.00156.00175.00206.00
24.0030.0036.5044.5051.0065.0076.1593.50112.60120.50141.30170.00220.50274.00324.00356.00406.00459.00508.00609.00660.00762.00914.00
0.080.110.250.350.450.801.131.822.502.864.656.4510.6618.0027.0030.0034.0044.0054.00101.00120.00190.00310.00
19.0022.0027.0032.0033.0038.0041.0044.0051.0051.0057.0060.0070.0078.0086.0089.0094.00103.00117.00137.00156.00175.00206.00
A C ApproxWeight A
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.50254.00304.50336.50387.00438.00489.00590.00641.00743.00895.00
0.070.110.180.320.360.681.021.702.303.103.906.7013.0016.0027.0032.0042.0057.0080.00114.00138.00230.00336.00
D ApproxWeight
OUTLET SIZEREDUCED SIZES
Buttweld Outlets • EXTRA STRONG
REDUCING SIZE FULL SIZE
FULL SIZES
FULL SIZES
OUTLET SIZE
REDUCED SIZES
1/23/41
1¼1½2
2½3456
Socketweld Outlets • 3000 LBS (SOCKET WELD TO ASME B16.11)
Socketweld Outlets • 6000 LBS (SOCKET WELD TO ASME B16.11)
Buttweld Outlets • SCH. 160 AND XXS
1/23/41
1¼1½2
2½3
3½4
6
25.0027.0033.0033.0035.0038.0041.0046.0049.0049.00
24.0030.0036.5044.5051.0065.0076.1593.50101.50120.50
31.8036.6046.1055.6062.0074.7087.40104.80122.30130.20
10.0013.0013.0013.0013.0016.0016.0016.0019.0019.00
0.1400.1500.3000.4000.4700.7301.2501.7201.9503.300
25.0027.0033.0033.0035.0038.0041.0046.0049.0049.00
16.0021.0026.7035.0040.9052.5062.8077.9090.10102.20
31.8036.6046.1055.6062.0074.7087.40104.80122.30130.20
10.0013.0013.0013.0013.0016.0016.0016.0019.0019.00
0.0600.1100.3000.3000.4000.6301.0301.7001.9503.000
A C F G AApproxWeight D F G Approx
WeightOUTLET SIZE
REDUCED SIZES
1/23/41
1¼1½2
32.0037.0040.0041.0043.0052.00
32.0037.0040.0041.0043.0052.00
19.0025.5033.4038.0049.3070.00
11.8015.6020.729.534.0052.00
40.0046.0057.2065.1076.3092.10
40.0046.0057.2065.1076.3092.10
10.0013.0013.0013.0013.0016.00
10.0013.0013.0013.0013.0016.00
0.2500.3700 6000.7500.9202.350
0.2500.3700 6000.7500.9202.350
A AC DF FG GApproxWeight
ApproxWeight
OUTLET SIZE
FULL SIZES
28.0032.0038.0044.0051.0055.0062.0073.0084.0094.00105.00
14.3019.0025.5033.4038.0042.9053.9073.0098.40122.20146.00
0.1100.3200.3800 5700.8001.001,5502.9004.7706.47012.80
28.0032.0038.0044.0051.0055.0062.0073.0084.0094.00
105.00
14.3019.0025.5033.4038.0042.9053.9073.0098.40122.20146.00
11.8015.6020.7029.5034.0042.9054.0066.6087.30109.50131.80
6.9011.0015.2022.8027.9038.2045.0058.4080.10
103.20124.40
0.1100.3200.3800.5700.8001.00
1.5502.9004.7706.47013.80
A C ApproxWeight A D D 5160 D XXS Approx
Weight
REDUCED SIZES
REDUCING SIZE FULL SIZE
REDUCING SIZE FULL SIZE
31.8036.6046.1055.6062.0074.7087.40104.80122.30130.20
F Approx.Weight
0.0700.1100.2000.3200.4100.6501.1301.9502.0503.090
Approx.Weight
FULL SIZES
OUTLET SIZEREDUCED SIZES
REDUCED SIZES
REDUCED SIZES
1/23/41
1¼1½2
898989898989
2430
36.544.55165
898989898989
14.519.025.533.438.043
A C A C
OUTLET SIZE 6000 Lbs3000 Lbs
1/23/41
1¼1½2
2½3
3½4
Threaded Outlets • 6000 lbs
Nipple Outlets • (PLAIN END • THREADED END & BEVEL END)
Threaded Outlets • 3000 lbs
1/23/41
1¼1½2
32.0037.0040.0041.0043.0052.00
19.0025.5033.4038.0049.3070.00
40.0046.0057.2065.1076.3092.10
32.0037.0040.0041.0043.0052.00
17.5022.8028.7037.4043.4055.50
40.0046.0057.2065.1076.3092.10
0.2000.3500.6000.7100.9002.300
0.2000.3500.6000.7100.9002.300
7
A C F A D F Approx.Weight
Approx.Weight
OUTLET SIZE
A C A
25.0027.0033.0033.0035.0038.0046.0051.0054.0057.00
24.0030.0036.5044.5051.0065.0076.1593.50101.50120.50
0.1100.1600.3000.4100.4500.8001.3702.0002.6103.230
25.0027.0033.0033.0035.0038.0046.0051.0054.0057.00
17.5022.8028.7037.4043.4055.5066.1081.8094.50107.20
31.8036.6046.1055.6062.0074.7087.40104.80117.50130.20
D F
FULL SIZES
REDUCING SIZE FULL SIZE
SPROMAK LTD® are the manufacturers of the INSERT BRANCH OUTLET. A header is weakened when an opening is created to install a branch outlet fitting, it could result in extra reinforcement being required to restore the strength of the opening. This is why the INSERT BRANCHOUTLETS are designed to provide a 100% reinforcement. The reinforcement design of the INSERTBRANCH OUTLET enables shorter installation time and most importantly the benefits of radiograph or ultrasonic examination after fabrication.DESIGN CODESInsert Branch Outlets can be supplied to comply with various piping and pressure vessel codes such asASME B31.1, B31.3, B31.4, B31.8, Stoomwezen, PD5500, ASME Section 1, Section VIII div 1 & 2 andmany more.
Reinforcement design calculations can be supplied on request.
STRESSDetailed calculations for stress intensification factors or stress indices can be supplied on request on all sizes.
PROOF TESTSThe Insert Branch Outlet has undergone proof testing to ASME B16.9 to prove the design integrity.
Custom made Insert Branch Outlets with extended “A” heights suitable for inserting into dished or hemispherical ends, etc, can be produced to suit customer’s requirements.
A variant of this fitting, the FLANGED INSERT OUTLET is also manufactured on a made to order basis with specific dimensional data made available against specific enquiry only at present.
The Insert Branch Outlet has been developed to meet the requirements of industry for a good quality insert type branch fitting that is an economical alternative to:-
a) Welding tees used in piping systems andb) Special nozzles used in pressure vessels.
Here are some of the advantages offered by the Insert Branch Outlet:-
a) Easy to perform and readily interpretable radiography of both attachments welds.b) Branch reinforcements to give 100% strength.c) Available in any Branch size, wall thickness or metallic material.d) Complies with most piping and pressure vessel codes for area replacements.e) The exterior and interior shape provides excellent distribution of stresses and gives good
internal flow characteristicsf) Easy and economical to install, with minimum amount of weld metal required to complete
an effective branch connection.
8
SPROMAK LTD®
INSERT BRANCH OUTLETS
BRANCH OUTLETN.B.
INSERT BRANCH OUTLET DIMENSIONS UP TO AND INCLUDING XS HEADER
The following table gives the range of Header and Branch sizes covered by INSERT BRANCH OUTLETS for use with header wall thicknesses up to an including XS.*
9
1/ 23/ 4
111/ 4
11/ 2
2346810121416182024
11/ 2
222
21/ 2
34681012161820222430
11/ 4
11/ 4
11/ 4
11/ 4
11/ 2
13/ 4
223/ 8
21 1/ 1 6
331/ 8
33/ 8
35/ 8
33/ 4
45/ 8
51/ 8
55/ 8
3232323238445160687679869295117130143
SIZESAVAILABLE
ONREQUEST
.36
.45
.50
.59
.801.503.105.511.020.029.044.655.664.480.094.4142.0
MIN. HEADER**N.B.
DIMENSIONSA B, B1 ETC
APPROXIMATEWEIGHT - Kg
* Dimensions for use with header wall thicknesses heavier than XS are available on request.** There is no limit to the maximum header size for Insert Branch Outlets
21 /2 -
11 /412
- 3
21 /2 -
11 /412
- 3
11 /2 -
11 /45
- 212
- 6
21 /2 -
25
- 312
- 6
2 - 2
5 - 3
12 -
62
- 25
- 312
- 6
5 - 4
8 - 6
12 -
10
1 /4 3 /8 1 /2 3 /4 1 11 /4 11 /4
in 11 /2 11 /2
12 3 /3
2
21 /8 27 /8 31 /8
43 /1 6
mm
36.5
36.5
43.6
54.0
67.5
76.2
104.
8
in 11 /4 11 /4
11 3 /3
2
12 5 /3
2
25 /3
2
21 /2 31 /4
mm
31.8
31.8
35.7
45.2
54.8
63.5
82.6
in 1 1 1 21 /4
23 /1 6
25 /1 6
23 /4
mm
39.7
39.7
47.6
57.2
61.9
66.7
81.0
lb 75 75 85 1.25 2.2
2.9
6.15
kg 34 34 39 57 1.00
1.32
2.80
6000
LB
s TH
REA
DED
AN
D S
OC
KET
WEL
D S
ched
ule
160
and
Dou
ble
Extr
a St
rong
But
t-wel
d
21 /2 -
11 /412
- 3
2½ -
11 /412
- 3
21 /2 -
11 /212
- 3
11 /2 -
11 /45
- 212
- 6
21 /2 -
25
- 312
- 6
21 /2 -
25
- 312
- 6
21 /2 -
25
- 312
- 6
5 - 4
8 - 6
12 -
10
OR
DE
RS
PE
CFI
CR
UN
PIP
E S
IZE
S
1 /4 3 /8 1 /2 3 /4 1 11 /4 11 /2 2 **3
**4
**6
in 17 /1 6
17 /1 6
17 /1 6
12 3/3 2
21 /8
22 1/3 2 3 41 /8
41 5/1 6
67 /1 6
9
mm
36.5
36.5
36.5
43.6
54.0
67.5
76.2
104.
8
125.
416
3.5
228.
6
in 11 /4 11 /4 11 /4
11 3/3 2
12 6/3 2
25 /3 2
21 /2 31 /4 31 /2 41 /2 65 /8
mm
31.8
31.8
31.8
35.7
45.2
54.6
63.5
82.6
88.9
144.
316
8.3
in 19 /1 6
19 /1 6
19 / 1 6
17 /8 21 /4
27 / 1 6
25 /8
33 /1 6
31 /4 41 /2 61 /8
mm
39.7
39.7
39.7
47.6
57.2
61.9
66.7
81.0
95.3
114.
315
5.6
lbs.
0.50
0.50
0.65
0.75
1.15
1.90
2.65
5.25
6.25
11.7
528
.00
Kg.
0.23
0.23
0.30
0.34
0.52
0.86
1.20
2.39
2.84
5.34
12.7
3
Elbo
w O
utle
tsLa
tera
l Out
let
36-1
1 /436
-11 /4
36-1
1 /436
-11 /4
36-2
36-2
36-2
36-3
Ord
erto
Spe
cific
Elb
owS
izes
1 /4 3 /8 1 /2 3 /4 1 11 /4 11 /2 2 3 4 6 8 10 12
in 11 /2 11 /2 11 /222
3 /3 2
21 /8 27 /8 31 /843 /1
6
CC
mm
38.1
38.1
38.1
43.6
54.0
73.0
79.4
106.
4
in 11 /4 11 /4 11 /411
3 /3 2
12 5 /3
2
25 /3 2
21 /2 31 /4
DD
mm
31.8
31.8
31.8
35.7
45.2
54.8
63.5
82.6
in 11 /2 11 /2 11 /212
5 /3 2
21 /1 6
23 /1 6
25 /1 6
23 /4
EE
mm
38.1
38.1
38.1
45.2
52.4
55.6
58.8
69.9
lbs.
0.50
0.50
0.65
0.75
1.15
1.90
2.65
5.25A
ppro
x. W
tA
ppro
x. W
tK
g.
0.23
0.23
0.30
0.34 52 86 1.20
2.39
Nomi
nal
Elbo
w Si
zeInc
hes
Nomi
nal
Elbo
w Si
zeInc
hes
Outle
tSi
ze-
Inche
s
Outle
tSi
ze-
Inche
s
DIM
EN
SIO
NS
DIM
EN
SIO
NS
36-1
1 /436
-11 /4
36-1
1 /436
-2
36-2
36-2
36-3
1 /4 3 /8 1 /2 3 /4 1 11 /4 11 /4
in 11 /2 11 /2
12 3 /3
2
21 /8 27 /8 31 /8
43 /1 6
mm
38.1
38.1
43.6
54.0
73.0
79.4
106.
4
in 11 /4 11 /4
11 3 /3
2
12 5 /3
2
25 /3 2
21 /2 31 /4
mm
31.8
31.8
35.7
45.2
54.8
63.5
82.6
in 11 /2 11 /2
12 5 /3
2
21 /1 6
23 /1 6
25 /1 6
23 /4
mm
38.1
38.1
45.2
54.4
55.6
58.8
69.9
lb 0.75
0.75
0.85
1.25
2.20
3.90
6.15
kg 0.34
0.34
0.39
0.57
1.00
1.77
2.80
6000
LB
s TH
REA
DED
AN
D S
OC
KET
WEL
D S
ched
ule
160
and
Dou
ble
Extr
a St
rong
But
t-wel
d
Dim
ensi
ons
for a
ll th
ree
styl
es a
re th
e sa
me
exce
pt fo
r the
“D” d
imen
sion
s on
the
butt
wel
ding
out
let
whi
ch m
atch
es th
e pr
oper
sch
edul
e on
the
bran
ch p
ipe.
3000
LB
s TH
REA
DED
AN
D S
OC
KET
WEL
D S
tand
ard
and
Extr
a St
rong
But
t-wel
d
Dim
ensi
ons
for a
ll th
ree
styl
es a
re th
e sa
me
exce
pt fo
r the
“D” d
imen
sion
s on
the
butt
wel
ding
out
let
whi
ch m
atch
es th
e pr
oper
sch
edul
e on
the
bran
ch p
ipe.
3000
LB
s TH
REA
DED
AN
D S
OC
KET
WEL
D S
tand
ard
and
Extr
a St
rong
But
t-wel
d
DIM
EN
SIO
NS
ON
AP
PLI
CAT
ION
½
10
There are many types of fittings in this group; they cover an extensive range and compliment the non-flanged range of Outlet fittings manufactured by SPROMAK LTD. Flanged Branch Outlets encompass the following specific types:FLANGED BUTTWELD OUTLET ____ FLANGED BUTTWELD OUTLET LIGHTWEIGHTFLANGED NIPPLE OUTLET ________ FLANGED NIPPLE OUTLET LIGHTWEIGHTFLANGED LATERAL OUTLET ______ FLANGED LATERAL OUTLET LIGHTWEIGHTFLANGED ELBOW OUTLET ________ FLANGED ELBOW OUTLET LIGHTWEIGHTFLANGED INSERT BRANCH OUTLETEach Flanged Branch Outlet is designed to fully compensate the hole cut into the header pipe.The tabulated data is applicable for header and branch pipes of the same wall thickness or schedule i.e. STD/STD or XS/XS etc. Flanged Branch Outlets are also supplied for various other wall thickness and outlet sizes not shown in the published data. These fittings can be supplied to fit any header pipe, pressure vessel, dished end or flat end. Dimensional data is available on request.Custom made items are readily produced to suit specific piping or pressure vessel layout requirements.Flanged Branch Outlets are supplied in most types of forged metals, from carbon and alloy steels, through stainless and super duplex, to aluminium and Cu. Ni. alloys.
The flanged part of the fitting complies with the specified flange standards. The compensation and base part of the fitting complies with our equivalent Buttweld, Nipple, Lateral, Elbow or Insert Outlet which would be used for the same header and branch pipe sizes and wall thicknesses.These fittings have undergone extensive full size Internal Pressure Proof Testing in accordance with ASME B16.9. They can be supplied to comply with any piping or pressure vessel code.Flanged Branch Outlets are available with branch ends suitable for use with various proprietary flanged end type connectors.
ORDERING INFORMATIONData we require to service your enquiry/order.1) HEADER SIZE: Actual Pipe O.D., I.D. or Nominal Pipe Size2) BRANCH SIZE: Actual Pipe O.D., I.D. or Nominal Pipe Size3) HEADER WALL THICKNESS: Schedule, or actual thickness.4) BRANCH WALL THICKNESS: Schedule, or actual thickness.5) TYPE OF FITTING: Flanged Buttweld Outlet, etc.6) FLANGE RATING.7) FLANGE FACING.8) MATERIAL.9) ANY SPECIAL REQUIREMENTS: For example if a special standout height is required.
REINFORCEMENT CALCULATIONSIf reinforcement calculations are required, the following data should be supplied with the enquiry.1) DESIGN CODE: (e.g. ASME B31.3) etc.2) DESIGN TEMPERATURE. 3) DESIGN PRESSURE.4) MATERIAL, FOR HEADER & BRANCH PIPES.5) CORROSION / EROSION ALLOWANCES FOR RUN AND BRANCH PIPES.6) HEADER PIPE MILL TOLERANCE.
11
Flanged Branch Outlets
12
EQUAL AND REDUCING__STD__/__STD__(unless shown thus*)
1/23/41
1¼11/ 2
221/ 2
331/ 2
456810121416
18 R*18 E*20 R*20 E*
24
88.9098.60107.95117.50127.00152.40177.80190.50215.90228.60254.00279.40342.90406.40482.60533.40596.90635.00635.00698.50698.50812.63
11.2012.7014.3015.9017.5019.0522.2523.8223.8223.8223.8225.4028.6030.2031.7534.9336.5239.7039.7042.8742.8747.63
65.0075.0085.0090.0095.00105.00112.00115.00120.00130.00146.00150.00175.00180.00200.00220.00225.00240.00245.00250.00265.00300.00
24.0030.0036.5044.5051.0065.0076.1593.50112.60120.50141.30170.00220.50274.00324.00356.00406.00459.00473.00508.00508.00609.00
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.70254.50304.80336.50387.35
-483.15
-489.00590.50
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.70254.50304.80336.50387.35483.15483.15489.00489.00590.50
0.671.051.652.242.834.31
1111111111111111111111
B E A C D F Weight TypeOUTLET SIZE
EQUAL AND REDUCING__STD__/__STD__(unless shown thus*)
1/23/41
11/ 4
11/ 2
221/ 2
331/ 2
456810121416
18R*18E*20 R*20 E*
24
95.25117.50123.80133.35155.60165.10190.50209.55228.60254.00279.40317.50381.00444.50520.70584.20647.70711.20711.20774.70774.70914.40
14.3015.9017.5019.0020.6022.2025.4028.6030.2031.7534.9336.5241.2847.6350.8053.9857.1560.3360.3363.5063.5069.85
70.0080.0090.0095.00100.0011000120.00125.00130.00140.00155.00160.00180.00195.00215.00230.00240.00255.00260.00265.00280.00310.00
24.0030.0036.5044.5051.0065.0076.1593.50112.60120.50141.30170.00220.50274.00324.00356.00406.00459.00473.00508.00508.00609.00
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.70254.50304.80336.50387.35
-483.15
-489.00590.50
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.70254.50304.80336.50387.35483.15483.15489.00489.00590.50
0.991.722.293.014.125.36
2211111111111112222221
B E A C D F Weight TypeOUTLET SIZE
R* indicates reducing size only. E* indicates equal size only. The unit of weight is kg. Weights given are for carbon steel. Raised Face flangers shown. Other facings are avaible
Flanged Buttweld Outlets • 300 lbsDIMENSIONS FOR HEADER AND BRANCH WALL STD / STD
R* indicates reducing size only. E* indicates equal size only. The unit of weight is kg. Weights given are for carbon steel. Raised Face flangers shown. Other facings are avaible
Flanged Buttweld Outlets • 150 lbsDIMENSIONS FOR HEADER AND BRANCH WALL STD / STD
13
EQUAL AND REDUCING__STD__/__STD__(unless shown thus*)
1/23/41
1¼1½2
2½3
3½456810121416
18 R*18 E*20 R*20 E*
24
95.25117.50123.80133.35155.60165.10190.50209.55228.60273.05330.20355.60419.10508.00558.80603.20685.80724.90724.90812.80812.80939.80
20.6522.2523.8526.9528.5531.7534.9538.1042.2844.4550.8053.9861.9569.8573.0376.2082.5588.9088.9095.2595.25107.95
80.0085.0095.00105.00110.00120.00125.00135.00140.00160.00180.00185.00210.00240.00250.00260.00280.00290.00295.00300.00315.00355.00
24.0030.0036.5044.5051.0065.0076.1593.50112.60120.50141.30170.00220.50274.00324.00356.00406.00459.00473.00508.00508.00609.00
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.70254.50304.80336.50387.35
-483.15
-489.00590.50
15.8021.0026.6035.0040.9052.5062.8078.0090.20102.20128.20154.00202.70254.50304.80336.50387.35483.15483.15489.00489.00590.50
1.131.862.463.434.686.18
2211111111222222222221
B E A C D F Weight TypeOUTLET SIZE
EQUAL AND REDUCING__STD__/__STD__(unless shown thus*)
1/23/41
1¼1½2
2½3456810121416
18 R*18 E*20 R*20 E*
24
120.65130.20149.20158.80177.80215.90244.50241.30292.10349.25381.00469.90546.10609.60641.35704.85787.40787.40857.25857.251041.40
28.5531.7534.9534.9538.0544.4547.6544.4550.8057.1561.9869.8576.2085.6092.2095.25107.95107.95114.30114.30146.05
85.00100.00105.00110.00125.00145.00155.00155.00170.00190.00210.00240.00270.00295.00310.00315.00330.00340.00355.00370.00445.00
24.0030.0036.5044.5051.0065.0076.1593.50120.50141.30170.00220.50274.00324.00356.00406.00459.00473.00508.00508.00609.00
15.8021.0026.6035.0040.9052.5062.8078.00102.20128.20154.00202.70254.50304.80336.50387.35
-483.15
-489.00590.50
15.8021.0026.6035.0040.9052.5062.8078.00102.20128.20154.00202.70254.50304.80336.50387.35483.15483.15489.00489.00590.50
2.112.974.335.237.1913.42
211112222222222222222
B E A C D F Weight TypeOUTLET SIZE
R* indicates reducing size only. E* indicates equal size only. The unit of weight is kg. Weights given are for carbon steel. Raised Face flangers shown. Other facings are avaible
Flanged Buttweld Outlets • 900 lbsDIMENSIONS FOR HEADER AND BRANCH WALL STD / STD
R* indicates reducing size only. E* indicates equal size only. The unit of weight is kg. Weights given are for carbon steel. Raised Face flangers shown. Other facings are avaible
Flanged Buttweld Outlets • 600 lbsDIMENSIONS FOR HEADER AND BRANCH WALL STD / STD
14
EQUAL AND REDUCING__STD__/__STD__(unless shown thus*)
1/23/41
1¼1½2
2½3456810121416
18 R*18 E*20 R*20 E*
24
120.65130.20149.20158 80177.80215.90244.50266.70311.10374.60393.70482.60584.20673.10749.30825.50914.4091440984.20984.201168.40
28.5531.7534.9534.9538.0544.4547.6553.9860.3579.3888.9098.45114.30130.18139.70152.40168.28168.28184.15184.15209.55
85.00100.00105.00110.00125.00145.00155.00170.00180.00220.00240.00290.00340.00375.00395.00410.00430.00435.00465.00480.00555.00
24.0030.0036.5044.5051.0065.0076.1593.50120.50141.30170.00220.50274.00324.00356.00406.00459.00473.00508.00508.00609.00
15.8021.0026.6035.0040 9052 5062.8078.00102.20128.20154.00202.70254.50304.80336.50387.35
-483.15
-489.00590.50
15.8021.0026.6035.0040.9052.5062.8078.00102.20128.20154.00202.70254.50304.80336.50387.35483.15483.15489.00489.00590.50
2.112.974.335.237.191342
211112222222222222222
B E A C D F Weight TypeOUTLET SIZE
EQUAL AND REDUCING__STD__/__STD__(unless shown thus*)
1/23/41
1¼1½2
2½345681012
133.35139.70158.75184.15203.20234.95266.70304.80355.60419.10482.60552.45673.10762.00
36.5138.1041.2844.4550.8057.1563.5073.0382.5598.43114.30133.35171.45190.50
100.00110.00125.00135.00150.00170.00190.00220.00250.00290.00340.00395.00505.00555.00
24.0030.0036.5044.5051.0065.0076.1593.50120.50141.30170.00220.50274.00324.00
15.8021.0026.6035.0040.9052.5062.8078.00102.20128.20154.00202.70254.50304.80
15.8021.0026.6035.0040.9052.5062.8078.00102.20128.20154.00202.70254.50304.80
3.824.646.389.3212.4218.40
22222222222222
B E A C D F Weight TypeOUTLET SIZE
R* indicates reducing size only. E* indicates equal size only. The unit of weight is kg. Weights given are for carbon steel. Raised Face flangers shown. Other facings are avaible
Flanged Buttweld Outlets • 2500 lbsDIMENSIONS FOR HEADER AND BRANCH WALL STD / STD
R* indicates reducing size only. E* indicates equal size only. The unit of weight is kg. Weights given are for carbon steel. Raised Face flangers shown. Other facings are avaible
Flanged Buttweld Outlets • 1500 lbsDIMENSIONS FOR HEADER AND BRANCH WALL STD / STD
15
EQUAL AND REDUCING__STD__/__STD__
1/23/41
1¼1½2
88.9098.60107.95117.50127.00152.40
11.2012.7014.3015.9017.5019.05
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
15.8021.0026.6035.0040.9052.50
15.8021.0026.6035.0040.9052.50
1.101.662.433.253.885.48
111111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 150 lbs
EQUAL AND REDUCING__STD__/__STD__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
14.3015.9017.5019.0020.6022.20
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
15.8021.0026.6035.0040.9052.50
15.8021.0026.6035.0040.9052.50
1.532.433.164.005.186.52
201111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 300 lbs
EQUAL AND REDUCING__STD__/__STD__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
20.6522.2523.8526.9528.5531.75
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
15.8021.0026.6035.0040.9052.50
15.8021.0026.6035.0040.9052.50
1.592.523.304.235.537.05
221111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 600 lbs
EQUAL AND REDUCING__STD__/__STD__
1/23/41
1¼1½2
120.65130.20149.20158.80177.80215.90
28.5531.7534.9534.9538.0544.45
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
15.8021.0026.6035.0040.9052.50
15.8021.0026.6035.0040.9052.50
2.543.504.925.947.7413.62
211112
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 900-1500 lbs
The unit of weight is kg. Weights given are for carbon sheets. Raised Face flanges shown. Other facings are available
LONGITUDINAL SECTION TRANSVERSE SECTION
16
EQUAL AND REDUCING__STD__/__STD__
1/23/41
1¼1½2
133.35139.70158.75184.15203.20234.95
36.5538.0541.2544.4550.7557.15
150.00150.00150.00150.00150.00165.00
24.0030.0036.5044.5051.0065.00
15.8021.0026.6035.0040.9052.50
15.8021.0026.6035.0040.9052.50
3.824.646.389.3212.4218.40
222222
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 2500 lbs
EQUAL AND REDUCING__XS__/__XS__
1/23/41
1¼1½2
88.9098 60107.95117.50127.00152.40
11.2012.7014.3015.9017.5019.05
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
13.9018.9024.3032.5038.1049 30
13.9018.9024.3032.5038.1049 30
1.141.702.543.414.095.79
111111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 150 lbs
EQUAL AND REDUCING__XS__/__XS__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
14.3015.9017.5019.0020.6022.20
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
13.9018.9024.3032.5038.1049.30
13.9018.9024.3032.5038.1049 30
1.582.503.274.165.396.83
221111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 300 lbs
EQUAL AND REDUCING__XS__/__XS__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
20.6522.2523.8526.9528.5531.75
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
13.9018.9024.3032.5038.1049.30
13.9018.9024.3032.5038.1049.30
1.642.603.364.405.737.36
221111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 600 lbs
The unit of weight is kg. Weights given are for carbon sheets. Raised Face flanges shown. Other facings are available
LONGITUDINAL SECTION TRANSVERSE SECTION
17
EQUAL AND REDUCING__XS__/__XS__
1/23/41
1¼1½2
120.65130.20149.20158.80177.80215.90
28.5531.7534.9534.9538.0544.45
150.00150.00150.00150.00150.00150.00
24.0030.0036.5044.5051.0065.00
13.9018.9024.3032.5038.1049.30
13.9018.9024.3032.5038.1049.30
2.593.585.036.107.9413.93
211112
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 900-1500 lbs
EQUAL AND REDUCING__XS__/__XS__
1/23/41
1¼1½2
133.35139.70158.75184.15203.20234.95
36.5538.0541.2544.4550.7557.15
150.00150.00150.00150.00150.00165.00
24.0030 0036.5044.5051.0065.00
13.9018.9024.3032.5038.1049.30
13.9018.9024.3032.5038.1049.30
3.874.716.499.4812.6218.74
222222
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 2500 lbs
EQUAL AND REDUCING__S__160__/__S__160
1/23/41
1¼1½2
88.9098.60107.95117.50127.00152.40
11.2012.7014.3015.9017.5019.05
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
11.8415.6020.7029.4633.9842.90
1.231.832.553.424.195.81
111111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 150 lbs
EQUAL AND REDUCING__S__160__/__S__160__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
14.3015.9017.5019.0020.6022.20
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
11.8415.6020.7029.4633.9842.90
1.622.643.234.175.526.84
222212
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 300 lbs
The unit of weight is kg. Weights given are for carbon sheets. Raised Face flanges shown. Other facings are available
LONGITUDINAL SECTION TRANSVERSE SECTION
18
EQUAL AND REDUCING__S__160__/__S__160
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
20.6522.2523.8526.9528.5531.75
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
11.8415.6020.7029.4633.9842.90
1.692.733.384.415.847.41
222212
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 600 lbs
EQUAL AND REDUCING__S__160__/__S__160
1/23/41
1¼1½2
120.65130.20149.20158.80177.80215.90
28.5531.7534.9534.9538.0544.45
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
11.8415.6020.7029.4633.9842.90
2.643.685.066.138.1613.98
212212
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 900-1500 lbs
EQUAL AND REDUCING__S__160__/__S__160
1/23/41
1¼1½2
133.35139.70158.75184.15203.20234.95
36.5538.0541.2544.4550.7557.15
150.00150.00150.00150.00150.00165.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
11.8415.6020.7029.4633.9842.90
3.924.846.529.5112.7518.86
222222
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 2500 lbs
EQUAL AND REDUCING__XXS__/__XXS__
1/23/41
1¼1½2
88.9098.60107.95117.50127.00152.40
11.2012.7014.3015.9017.5019.05
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
6.4011.0315.2122.7627.9438.18
1.281.912.743.754.536.16
111111
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 150 lbs
The unit of weight is kg. Weights given are for carbon sheets. Raised Face flanges shown. Other facings are available
LONGITUDINAL SECTION TRANSVERSE SECTION
19
EQUAL AND REDUCING__XXS__/__XXS__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
14.3015.9017.5019.0020.6022.20
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042 90
14.3019.0025.5033.4038.0042.90
6.4011.0315.2122.7627.9438.18
1.722.713.424.495.867.20
222212
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 300 lbs
EQUAL AND REDUCING__XXS__/__XXS__
1/23/41
1¼1½2
95.25117.50123.80133.35155.60165.10
20.6522.2523.8526.9528.5531.75
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
6.4011.0315.2122.7627.9438.18
1.722.803.524.746.307.77
222212
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 600 lbs
EQUAL AND REDUCING__XXS__/__XXS__
1/23/41
1¼1½2
120.65130.20149.20158.80177.80215.90
28.5531.7534.9534.9538.0544.45
150.00150.00150.00150.00150.00150.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
6.4011.0315.2122.7627.9438.18
2.733.805.256.458.5114 34
212212
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 900-1500 lbs
EQUAL AND REDUCING__XXS__/__XXS__
1/23/41
1¼1½2
133.35139.70158.75184.15203.20234.95
36.5538.0541.2544.4550.7557.15
150.00150.00150.00150.00150.00165.00
14.3019.0025.5033.4038.0042.90
14.3019.0025.5033.4038.0042.90
6.4011.0315.2122.7627.9438.18
4.015.006.719.8413.1019.25
222222
B E A C D F Weight TypeOUTLET SIZE
Flanged Nipple Outlets • 2500 lbs
The unit of weight is kg. Weights given are for carbon sheets. Raised Face flanges shown. Other facings are available
LONGITUDINAL SECTION TRANSVERSE SECTION
Spromak LTD 11G WILSON ROAD, HUYTON, LIVERPOOL L36 6AN ENGLAND TEL 0151-480 0592 FAX 0151-480 0656E-MAIL [email protected] WEBSITE www.spromak.co.uk
Examples of our previous projects
Project Client CountryScott Field Amerada Hess UKShell Nelson Shell UK Exploration UKPiper Bravo Elf Caledonian UKADCO Abu Dhabi Oil Co Abu DhabiBritish Gas N.Morcambe British Gas UKBritish Gas Rough Enhacement British Gas UKJudy-Joanne Phillips Petroleum UKTroll Onshore Statoil NorwayGoodwyn Platform A Woodside Petroleum AustraliaSaga Snorre Saga Petroleum Norway
Material Specifications(FORGED PRODUCTS)Forged fittings and other products can be supplied to any relevant material specification such as: ASTM, BS, DIN standards etc.Spromak Ltd®, are pleased to be able to supply fittings in any material grade used today by industry.Some of the more common material specifications are listed below. CARBON STEELSASTM: A105N, A350-LF2, A350-LF3, A694-F46, A694-F52, A694-F60, A694-F65. STAINLESS STEELSASTM: A182-F304*, A812-F310*, A182-F316*, A182-F321*, A182-F347*.A182-F348*.ALLOY STEELSASTM: A182-F1*, A182-F5*, A182-F6*, A182-F9*, A182-F11*, A182-F12*, A182-F21*, A182-F22*. SPECIAL ALLOYSASTM: A182-F51 Duplex and, A182 F53, A182 F55 Super Duplex.ASTM: A182-F44 (6 Mo).CUPRO NICKEL 90/10, and 70/30.ALUMINIUM ALLOYS.NICKEL ALLOYS N04400, N06625, N08825NICKEL 200*These materials are also available in various sub-grades as listed in the ASTM Standards
Nominal pipe sizeOutside diameter
Schedule 5SSchedule 10SSchedule 10Schedule 20Schedule 30
Schedule 40SStandard WallSchedule 40Schedule 60
Schedule 80SExtra StrongSchedule 80Schedule 100Schedule 120Schedule 140Schedule 160
Double Extra Strong
0.8400.7100.6740.674
0.6220.6220.622
0.5460.5460.546
0.4660.252
1.0500.9200.8840.884
0.8240.8240.824
0.7420.7420.742
0.6140.434
11.3151.1851.0971.097
1.0491.0491.049
0.9570.9570.957
0.8150.599
1¼1.6601.5301.4421.442
1.3801.3801.380
1.2781.2781.278
1.1600.896
1½1.9001.7701.6821.682
1.6101.6101.610
1.5001.5001.500
1.3381.100
22.3752.2452.1572.157
2.0672.0672.067
1.9391.9391.939
1.6891.503
2½2.8752.7092.6352.635
2.4692.4692.469
2.3232.3233.323
2.1251.771
33.5003.3343.2603.260
3.0683.0683.068
2.9002.9002.900
2.6242.300
3½4.0003.8343.7603.760
3.5483.5483.548
3.3643.3643.364
2.728
44.5004.3344.2604.260
4.0264.0264.026
3.8263.8263.826
3.624
3.4383.152
55.5635.3455.2955.295
5.0475.0475.047
4.8134.8134.813
4.563
4.3134.063
66.6256.4076.3576.357
6 0656.0656065
5.7615.7615.761
5.501
5.1894.897
88.6258.4078.3298.3298.1258.0717.9817.9817.9817.8137.6257.6257.6257.4397.1897.0016.8136.875
1010.75010.48210.42010.42010.25010.13710.02010.02010.0209.7509.7509.7509.5649.3149.0648.7508.5008.750
1212.75012.43812.39012.39012.25012.09012.00012.00011.93811.62611.75011.75011.37611.06410.75010.50010.12610.750
1414.00013.68813.62413.50013.37613.250
13.25013.12412.814
13.00012.50012.12611.81411.50011.188
1616.00015.67015.62415.50015.37615.250
15.25015.00014.688
15.00014.31413.93813.56413.12412.814
1818.00017.67017.62417.50017.37617.124
17.25016.87616.500
17.00016.12615.68815.25014.87614.438
2020.00019.62419.56419.50019.25019.000
19.25018.81418.376
19.00017.93817.43817.00016.50016.064
2222.00021.62421.56421.50021.25021.000
21.25020.75020.250
21.00019.75019.25018.75018.25017.750
2424.00023.56423.50023.50023.25022.876
23.25022.52622.064
23.00021.56420.93820.37619.87619.314
2626.000
25.250
25.000-
BUTTWELD OUTLET BORES and SCHEDULE SIZES (dimensions in inches)1/ 2
3/ 4
2626.000
0.3120.500
0.375
0.500
66.6250.1090.1340.134
0.2800.2800.280
0.4320.4320.432
0.562
0.7180.864
Nominal pipe sizeOutside diameter
Schedule 5SSchedule 10SSchedule 10Schedule 20Schedule 30
Schedule 40SStandard WallSchedule 40Schedule 60
Schedule 80SExtra StrongSchedule 80
Schedule 100Schedule 120 Schedule 140Schedule 160
Double Extra Strong
0.8400.0650.0830.083
0.1090.1090.109
0.1470.1470.147
0.1870.294
1.0500.0650.0830.083
0.1130.1130.113
0.1540.1540.154
0.2180.308
11.3150.0650.1090.109
0.1330.1330133
0.1790.1790.179
0.2500.358
1¼1.6600.0650.1090.109
0.1400.1400.140
0.1910.1910.191
0.2500.382
1½1.9000.0650.1090.109
0.1450.1450.145
0.2000.2000.200
0.2810.400
22.3750.0650.1090.109
0.1540.1540.154
0.2180.2180.218
0.3430.436
2½2.8750.0830.1200.120
0.2030.2030.203
0.2760.2760.276
0.3750.552
33.5000.0830.1200.120
0.2160.2160.216
0.3000.3000.300
0.4380.600
3½4.0000.0830.1200120
0.2260.2260.226
0.3180.3180.318
0.636
44.5000.0830 1200.120
0.2370.2370.237
0.3370.3370.337
0.438
0.5310.674
55.5630.1090.1340.134
0.2580.2580.258
0.3750.3750.375
0.500
0.6250.750
88.6250.1090.1480.1480.2500.2770.3220.3220.3220.4060.5000.5000.5000.5930.7180.8120.9060.875
1010.7500.1340.1650.1650.2500.3070.3650.3650.3650.5000.5000.5000.5930.7180.8441.0001.1251.000
1212.7500.1560.1800.1800.2500.3300.3750.3750.4060.5620.5000.5000.6870.8431.0001.1251.3121.000
1414.0000.1560.1880.2500.3120.375
0.3750.4380.593
0.5000.7500.9371.0931.2501.406
1616.0000.1650.1880.2500.3120.375
0.3750.5000.656
0.5000.8431.0311.2181.4381.593
1818.0000.1650.1880.2500.3120.438
0.3750.5620.750
0.5000.9371.1561.3751.5621.781
2020.0000.1880.2180.2500.3750.500
0.3750.5930.812
0.5001.0311.2811.5001.7501.968
2222.0000.1880.2180.2500.3750.500
0.3750.6250.875
0.5001.1251.3751.6251.8752.125
2424.0000.2180.2500.2500.3750.562
0.3750.6870.968
0.5001.2181.5311.8122.0622.343
3030.0000.2500.3120.3120.5000.625
0.375
0.500
3636.000
0.3120.5000.625
0.3750.750
0.500
DIMENSIONS OF SELECTED SIZES SEAMLESS PIPE TO ASME B36.10and ASME B36.19 Wall Thickness (All dimensions in inches)
1/ 23/ 4