Date post: | 21-Jul-2016 |
Category: |
Documents |
Upload: | all-aboard-design-co |
View: | 214 times |
Download: | 1 times |
Section 1 — Brochure/Flier Marketing
1
C46400 Alloy from Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. has been successfully satisfying a broad range of applications and industries with our wrought products. Specifically, C46400, naval brass, is widely used in marine construction where a strong, corrosion resistant and hard material is required.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
Standard Stocked | Low Lead
Builder HardwareLock Pins
ElectricalPrecision Shipboard Equipment
FastenersNuts | Bolts | Rivets
IndustrialAircraft Turnbuckle Barrels | Balls | Bearings
Valve Stems | Condensor Plates | Hub ConesPressure Vessels | Bushings | Heat Exchanger Tubes
MarineShafting | Turnbuckles | Hardware | Propeller Shafts
OrdnanceMissile Components
PlumbingFittings
C46400 Alloy Chemical Composition
Chemical Composition according to ASTM B21/B21M-12. Note: Single values represent maximums.
Alloy
C46400
Sb% As% Cr% Co% S%Al% Ni%Mn% Sn%P%Fe% Zn%Si%Pb%Cu%
59.0-62.0
0.50-1.00 Remainder0.200.10
C46400 Alloy Similar or Equivalent SpecificationCDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER
C46400 B21 J461, J463 QQ-B-639
C46400 Alloy Physical PropertiesUS Customary Metric
Melting Point - Liquidus 1650˚ F 899˚ C
Melting Point - Solidus 1630˚ F 888˚ C
Density 0.304 lb/in3 at 68˚ F 8.4 gm/cm3 at 20˚ C
8.41 8.41
Electrical Resistivity 39.9 ohms-cmil/ft at 68˚ F 4.32 microhm-cm at 20˚ C
Electrical Conductivity 26% IACS at 68˚ F 0.151 MegaSiemens/cm at 20˚ C
Thermal Conductivity 67 Btu · ft/(hr · ft2 · ˚F) at 68˚ F 116.0 W/m at 20˚ C
11.8 · 10-6 per ˚F (68˚-572˚ F) 20.4 ·10-6 per ˚C (20˚-300˚ C)
0.09 Btu/lb/˚F at 68˚ F 377.1 J/kg at 293˚ K
Modulas of Elasticity in Tension 15000 ksi 103422 MPa
Modulus of Rigidity 56000 ksi 38611 MPa
Physical Properties provided by CDA.
Specific Gravity
Coefficient of Thermal Expansion
Specific Heat Capacity
C46400 Alloy Mechanical Properties
Mechanical Properties according to ASTM B21/B21M-12H02 HALF-HARD TEMPER
SIZE RANGE: OVER 2" TO 3" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa
54 372 25 172 25 55-80
SIZE RANGE: ½" TO 1" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa
60 414 27 186 25 60-80
SIZE RANGE: ½" AND UNDER
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa % HRB
HRB
HRB
HRB
%
%
%
60 414 27 186 22
SIZE RANGE: OVER 1" TO 2" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa
58 400 26 179 25 55-80
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected] All Concast plants are ISO 9001:2008 certified
Section 1 — Brochure/Flier Marketing
2
C64200 Alloy from Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. has been successfully satisfying a broad range of applications and industries with our wrought products. Specifically, our C64200 aluminum bronze alloy is used in the power generation/energy, aerospace, automotive markets and industrial applications.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
C64200 is a Concast Standard-Stocked Alloy
AutomotiveValve Guides | Automobile Engines
ElectricalPole Line Hardware
FastenersNuts | Bolts
IndustrialValve Bodies | Valve Stems | Gears
Cams | Valve Components
MarineHardware
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected] All Concast plants are ISO 9001:2008 certified
C64200 Alloy Chemical Composition
C64200 Remainder
Alloy Cu%
0.20
Sn%
0.05
Pb%
0.50
Zn%
0.30
Fe%
0.25
Ni%
6.30-7.60
Al%
0.10
Mn%
1.50-2.20
Si%
0.15
As%
Chemical Composition according to ASTM B150/B150M-12.
Note: Single values represent maximums.
C64200 Alloy Similar or Equivalent SpecificationCDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER
C64200 ASTM B150 SAE J461, SAE J463 AMS 4634B QQ-C-465B AMD1
C64200 Alloy Physical PropertiesUS Customary Metric
Melting Point - Liquidus 1840˚ F 1004˚ C
Melting Point - Solidus 1800˚ F 982˚ C
Density 0.278 lb/in3 at 68˚ F 7.7 gm/cm3 at 20˚ C
7.690 7.69
Electrical Resistivity 113 ohms-cmil/ft at 68˚ F 18.79 microhm-cm at 20˚ C
Electrical Conductivity 8% IACS at 68˚ F 0.047 MegaSiemens/cm at 20˚ C
Thermal Conductivity 26 Btu · ft/(hr · ft2 · ˚F) at 68˚ F 45.0 W/m at 20˚ C
10 · 10-6 per ˚F (68˚-572˚ F) 18.0 ·10-6 per ˚C (20˚-300˚ C)
0.090 Btu/lb/˚F at 68˚ F 377.1 J/kg at 293˚ K
Modulas of Elasticity in Tension 16000 ksi 110000 MPa
Modulus of Rigidity 6000 ksi 41370 MPa
Physical Properties provided by CDA.
Specific Gravity
Coefficient of Thermal Expansion
Specific Heat Capacity
C64200 Alloy Mechanical Properties
Mechanical Properties according to ASTM B150/B150M-12
HR50 DRAWN AND STRESS RELIEVED TEMPER
SIZE RANGE: OVER 2" TO 3" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa
75 575 35 240 15 70-95
SIZE RANGE: ½" TO 1" ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa
85 585 45 310 12 80-100
SIZE RANGE: ½" AND UNDER
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa HRB%
HRB%
90 620 45 310 9
SIZE RANGE: OVER 1" TO 2" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Rockwell “B”Hardness
ksi MPa ksi MPa
80 550 42 290 12 80-100
HRB%
HRB%
Section 1 — Brochure/Flier Marketing
3
C63000 Alloy from Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. has been
successfully satisfying a broad range of
applications and industries with our wrought
products. Specifically, our C63000 nickel
aluminum bronze alloy is used in the power
generation/energy, power transmission and
control, marine and aerospace markets.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
C63000 is a Concast Standard-Stocked Alloy
Industrial Applications
Valve Seats | Plunger Tips | Shafting | Pump Parts
Condenser Tube for Power Stations and Desalting Units
Cams | Gears | Valve Guides | Aircraft Parts
Pump Shafts | Structural Members | Valve Balls
Corrosion-Resistant Articles | Bushings | Bearings
Hydraulic Bushings for Earth-Moving Equipment
Tanks | Heat Exchanger Flanges
Heat Exchangers | Headers
Marine Applications
Nuts | Propellers | Pump Parts | Bolts
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected] All Concast plants are ISO 9001:2008 certified
C63000 Alloy Chemical Composition
C63000 Remainder 0.20 0.30 1.50 0.254.00-5.50
9.00-11.00
Alloy Cu% Sn% Zn%
2.00-4.00
Fe% Ni% Al% Mn% Si%
Chemical Composition according to ASTM B150/B150M-12.
Note: Single values represent maximums.
C63000 Alloy Similar or Equivalent SpecificationCDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER
C63000 B150 SAE J461, SAE J463 4640H QQ-C-465B AMD1
C63000 Alloy Physical PropertiesUS Customary Metric
Melting Point - Liquidus 1930˚ F 1054˚ C
Melting Point - Solidus 1895˚ F 1035˚ C
Density 0.274 lb/in3 at 68˚ F 7.58 gm/cm3 at 20˚ C
7.58 7.58
Electrical Resistivity 116 ohms-cmil/ft at 68˚ F 19.28 microhm-cm at 20˚ C
Electrical Conductivity 70% IACS at 68˚ F 0.041 MegaSiemens/cm at 20˚ C
Thermal Conductivity 22.60 Btu · ft/(hr · ft2 · ˚F) at 68˚ F 39.1 W/m · ˚K at 20˚ C
90 · 10-6 per ˚F (68˚-572˚ F) 16.2 · 10-6 per ˚C (20˚-300˚ C)
0.090 Btu/lb/˚F at 68˚ F 377.1 J/kg at 293˚ K
Modulas of Elasticity in Tension 17500 ksi 121000 MPa
Modulus of Rigidity 6400 ksi 44130 MPa
Physical Properties provided by CDA.
Specific Gravity
Coefficient of Thermal Expansion
Specific Heat Capacity
C63000 Alloy Mechanical Properties
Mechanical Properties according to ASTM B150/B150M-12
HR50 DRAWN AND STRESS RELIEVED TEMPER
SIZE RANGE: OVER 2" TO 3" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Brinell Hardness
ksi MPa ksi MPa
105 725 55 380 10 187 to 241
SIZE RANGE: ½" TO 1" ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Brinell Hardness
110 760 68 470 10 201 to 248
SIZE RANGE: OVER 1" TO 2" INCLUSIVE ROD
Tensile Strength, min RemarksYield Strength, at .5% extension under load, min
Elongation, 4x diameteror specimen thickness
Brinell Hardness
ksi MPa ksi MPa
110 760 60 415 10 201 to 248
ksi MPa ksi MPa min to max BHN%
min to max BHN%
min to max BHN%
Section 1 — Brochure/Flier Marketing
4
Wrought Products from Concast
Improved Size and ConsistencyReduces machining losses
Dimensional consistency within each bar
Dimensional consistency from bar to bar
Tighter size and section tolerances
Increased Mechanical PropertiesYield and tensile strength
Hardness (may reduce the need for hardening)
Improved Machinability and Productivity
Allows for higher feeds and speeds and improved machined finish
Increased machining rates
Longer tool life
Improved yield
w w w . c o n c a s t . c o m
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
Standard-stocked alloysC31400 | C46400 | C51000 | C54400 | C63000 | C64200 | C67300
Other available alloysC31600 | C52100 | C53400 | C65100
Concast Metal Products Co. has been successfully satisfying a broad range of applications and industries with our wrought drawn alloys. Our wrought products are brought to final dimensions by one or more cold drawing operations with suitable intermediate anneals when necessary. After the final draw, the rods are straightened mechanically and cut to the desired length.
Copper AlloyUNS No
C31400
C31600
C51000
C53400
C54400
C63000
C64200
C65100
C67300
Sb% As% Cr% Co% S%Al% Ni%Mn% Sn%P%Fe% Zn%Si%Pb%Cu%
87.50-90.50
87.50-90.50
87.50-90.50
0.70-1.20
0.04-0.10
0.03-0.35
0.03-0.10
2.00-4.00
4.00-5.50
1.30-2.50
0.80-1.20
3.00-4.00
0.40-3.00
2.00-3.50
0.03-0.35
0.01-0.50
C52100
3.50-4.50
3.50-5.80
7.00-9.00
4.20-5.80
0.50-1.00
1.50-4.50
Remainder
Remainder
Remainder
Remainder
Remainder
Remainder
Remainder
Remainder
Remainder
0.005
0.005
0.25
0.10
0.10
0.70
0.10
0.10
0.10
0.10
0.30
0.80
0.50
1.50
0.10 0.25
0.25
1.50-2.20
0.80-2.00
0.50-1.50
0.25
0.05
1.90
C4640059.00-62.00
0.04-0.10 Remainder
Remainder
0.10 0.20
0.05
0.05
0.05
0.20
0.20
0.30
0.20
0.30
3.00
0.50
0.30
1.500.70
Wrought Products Chemical Composition
Wrought Products Typical UsesArchitecture Automotive Building Consumer Electrical Fasteners Industrial Marine Ordnance Plumbing
grillwork
bridge bearing plates
tanks
heater cores
thermostats
electrical connectors
locks
door knobs
hinges
kick plates
finish hardware
watch parts
costume jewelry
coinage
symbols
lamps
connectors
motors
wire
conduit
wire connectors
screwsnutscotter pinswashersnailsrivets
springschainswelding rodsgearsclipsclutch discs
nuts
propellers
propeller shafts
pump parts
hardware
ammunition cartridge cases
shells
ammunition
mechanical housings
faucets
Wrought Products
*standard-stocked alloys
Copper AlloyUNS No
ASTMSpec
C31400*
C31600
C46400*
C51000*
C52100
C53400
C54400*
C63000*
C64200*
C65100
C67300*
B140
B140
B21
B139
B139
B139
B139
B150
B150
B98
Leaded Commercial Bronze
Leaded Commercial Bronze (nickel-bearing)
Naval Brass
Phosphorous Bronze Rod
Phosphorous Bronze Rod
Phosphor Bronze
Phosphor Bronze
Aluminum Bronze
Aluminum Bronze
Low-Silicon Bronze
Manganese Bronze
Product DescriptionTemper/sRound
Size Range
0.375 to 2.5
0.375 to 2.5
0.500 to 2.75
0.375 to 2.5
0.375 to 2.5
0.375 to 2.5
0.375 to 2.5
0.375 to 10.0
0.1875 to 6.0
0.375 to 2.5
0.75 to 2.0
Hex/OctSize Range
0.375 to 2.0
0.375 to 2.0
0.500 to 2.75
0.375 to 2.0
0.375 to 2.0
0.375 to 2.0
0.375 to 2.0
consult mill
consult mill
0.375 to 2.0
0.75 to 2.0
HR50
HR50
H02
H02
H02
H02
H02
H04
H04
H04
H04
H04
H04
H04 H06
H08
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected] All Concast plants are ISO 9001:2008 certified
Section 1 — Brochure/Flier Marketing
5
Aerospace and Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. is a manufacturer of specialty continuous cast copper alloys. Our primary focus is the production of copper alloys in bars, rods, tubes and rectangles, as well as custom alloys. All products are produced with state-of-the-art horizontal and vertical continuous-casting technology.
We offer our customers a wide range of wrought drawn alloys, including C510 phosphor bronze, C630 nickel-aluminum bronze and C642 aluminum bronze.
Benefits of Continuous Cast:
Uniform structures (eliminates hard spots)
Favorable mechanical properties
Greater friction and wear properties
Excellent machinability and fabrication ability
Reasonable cost
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certifi ed
Standard-stocked alloysC51000 | C64200 | C63000 | C86300 | C90300 | C95400 | C95500
Other available alloysC86500 | C90500 | C93700 | C94100 | C94300 | C95510
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected] All Concast plants are ISO 9001:2008 certifi ed
Aerospace-Related ProductsCopper Alloy
UNS No. ASTMspec AMS spec
C51000*
C63000*
C64200*
C86300*
C86500
C90300*
C90500
C90700
C93700
C94100
C94300
C95400*
C95500*
C95510
B139
B150
B150
B505
B505
B505
B505
B505
B505B144, 3A
B505
B505
B505
B505
4625
4640
4631
4860
4845
4845
4880
Phosphor Bronze
Nickel Aluminum Bronze
Aluminum Bronze
Manganese Bronze
High-Strength Yellow Brass
Tin Bronze
Tin Bronze
Tin Bronze
High-Leaded Tin Bronze
High-Leaded Tin Bronze
High-Leaded Tin Bronze
Aluminum Bronze
Nickel Aluminum Bronze
Nickel Aluminum Bronze
Material Description
Requires low coefficent of friction, moderate strength and good electrical conductivity
Hardness, good corrosion resistance, high wear resistance
Hardness, good corrosion resistance, high wear resistance
Hardness, good corrosion resistance, high wear resistance
Good corrosion resistance to sea water, high wear resistance
Excellent self-lubricating characteristics
Excellent self-lubricating characteristics
High strength, tarnish resistant, good anti-frictional characteristics
Benefits
aircraft bushings, bearings
aircraft parts, pump shafts, structural members,corrosion resistant articles, landing gear parts
high load gear, bearing applications
high load gear, bearing applications
aircraft landing gear bushings
aircraft bushings and bearings
aircraft accessory drives
aircraft control bushings
aircraft carburetor bearings
aircraft carburetor bearings
bearing brushes, landing gear componentson aircrafts, engine components
aircraft components, landing gear parts
aircraft components, landing gear parts
Applications
*standard stocked alloys
Copper AlloyUNS No
C51000
C63000
C64200
C86300
C86500
C90300
C90500
C90700
C93700
C94100
C94300
C95400
C95500
C95510
Sb% As% Cr% Co% S%Al% Ni%Mn% Sn%P%
0.05
0.05
0.05
0.08
0.08
0.08
0.09
0.20
0.20
0.20
0.50
0.80
0.80
Fe% Zn%Si%Pb%Cu%
60.00-66.0055.00-60.0086.00-89.0086.00-89.0088.00-90.0078.00-82.0072.00-79.0067.00-72.00
8.00-11.0018.00-22.00
7.50-9.009.00-11.0010.00-12.00
3.00-5.001.00-3.00
Rem
Rem
Rem
83.00
78.00
78.00
9.00-11.00
10.00-11.5010.00-11.509.70-10.90
3.00-5.003.00-5.002.00-3.50
3.00-5.504.50-5.50
6.30-7.60
0.50-1.50
5.00-7.50
0.005
0.005
0.005
0.005
0.005
0.005
2.00-4.00
2.00-4.00
4.00-5.50
0.40-2.00
0.10
0.30
0.20
0.20
0.15
0.70
0.25
0.15
0.05
0.05
0.20
0.40
0.30
0.30
0.50
23.00-27.00
2.50-5.000.10-1.50
1.50
0.10
0.50
3.50
1.50
0.25
1.00
1.00
1.00
1.00
0.50
0.50
1.00
1.00
1.50
0.03-0.35
0.05
0.05
0.30
0.10
0.50
0.08
1.50-2.20
0.25
0.005
0.005
0.005
0.005
0.005
0.005
4.20-5.80
0.20
0.20
0.20
1.00
0.20
9.00-11.004.50-6.504.50-6.00
22.00-28.0036.00-42.00
0.30
0.30
0.50
0.50
0.80
1.00
0.80
0.30
Aerospace-Related Products Chemical Composition
Section 1 — Brochure/Flier Marketing
6
Oil & Gas Alloys from Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. manufactures a wide range of copper alloys specifi cally engineered for the oil and gas industry. These alloys support the market requirements for oil and gas market applications.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certifi ed
Oil & Gas ApplicationsBearings
Bushings
Hydraulic seals
Seals
Torque plugs
Pump parts
PDC matrix binder
Standard-stocked alloysC63000 | C64200 | C86300 | C93200 | C95400 | C95500
Other available alloysC95400HT | C95410 | C95500HT | C95520HT | C95800
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected] All Concast plants are ISO 9001:2008 certifi ed
Oil & Gas Industry-Related Products
AMS specCopper Alloy UNS No. ASTM spec
C63000*
C64200*
C86300*
C93200*
C95400*, C95400HT, C95410
C95500*, C95500HT, C95520HT, C95800
B150
B150
B505
B505
B505
B505
AMS4640
AMS4634B
AMS4862
Nickel Aluminum Bronze
Aluminum Bronze
Manganese Bronze
Leaded Tin Bronze
Aluminum Bronze
Nickel-Aluminum Bronze
Material Description
Hardness, good corrosion resistance,
high wear resistance
High strength, tarnish resistant,
good anti-frictional characteristics
Benefits Applications
*standard stocked alloys
valve seats, plunger tips, condenser desalting units, shafting,
pump parts, gears, valve guides, pump shafts, structural
members, corrosion resistant articles, hydraulic bushings for
earth moving equipment, valve balls, bushings, bearings,
welded piping systems
valve bodies, valve stems, gears, cams, valve components,
nuts, bolts, marine hardware
bushings, high strength machine parts, hooks, gears,
propellers, hydraulic cylinder parts, large valve stems, slow
speed, heavy load bearings, hydraulic cylinder part
thrust washers, pumps, bushings, machine parts, main spindle
bearings, machine tool bearings, bearings for cranes, trunion
bearings, roll neck bearings, fuel pump bushings, water pump
bushings, diesel engine wrist pin bushings, pump impellers,
general purpose bushings, fittings, pump fixtures, insert
bearings, bearings
bushings, high strength clamps, gears, valves, bearings, valve
bodies, machine parts, valve seats, valve guides, spur gears,
heavily loaded worm gears, pump parts
bushings, high strength clamps, gears, valves, bearings, valve
bodies, machine parts, valve seats, valve guides, spur gears,
heavily loaded worm gears, pump parts
Copper AlloyUNS No
C63000
C64200
C86300
C93200
C95400
C95400HT
C95410
C95500
C95500HT
C95520HT
C95800
Sb% As% Cr% Co% S%Al%
10.00-11.50
9.00-11.00
10.00-11.5010.00-11.50
10.50-11.508.50-9.50
6.30-7.60
10.00-11.50
11.00-11.50
5.00-7.50
0.005
Ni%
3.00-5.503.00-5.504.20-6.004.00-5.00
1.50-2.50
4.00-5.50
0.25
1.00
1.00
1.50
1.50
Mn%
2.50-5.00
0.80-1.50
1.50
0.10
0.50
0.50
0.50
3.50
3.50
1.50
Sn%
6.30-7.50
0.20
0.20
0.20
0.25
P%
0.15
0.20
0.05
0.08
0.09
0.35
Fe%
3.00-5.003.00-5.004.00-5.503.50-4.50
3.00-5.00
2.00-4.00
3.00-5.00
3.00-5.00
2.00-4.00
0.30
0.20
Zn%
1.00-4.00
22.00-28.00
0.30
0.50
0.30
Si%
1.50-2.20
0.25
0.005
0.15
0.10
Pb%
6.00-8.00
0.05
0.20
0.03
0.03
Cu%
81.00-85.00
60.00-66.00
Rem
Rem
83.00
83.00
83.00
78.00
78.00
74.50
79.00
Oil & Gas Industry-Related Products Chemical Composition
Section 1 — Brochure/Flier Marketing
7
Hydraulics Alloys from Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. manufactures a wide range of copper alloys specifically engineered for the hydraulics industry. These alloys support the market requirements for hydraulics market applications.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
Hydraulics ApplicationsPiston pumps
Gear pumpsThrust plates
Seal ringsPiston seals
Available alloysC93200* | C92900 | C93700 | C93800
*Standard stocked alloy
PDC Matrix Binder Alloys from Concast
w w w . c o n c a s t . c o m
As the largest producer of continuous cast copper alloys in North America, Concast Metal Products Co. offers unparalleled value for specifically engineered PDC matrix binder alloys.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
PDC Matrix Binder Alloys are Standard-Stocked Items
Polycrystalline Diamond Compact (PDC)
Binder for Drill Bits
Metallurgically blended
Third-party test confirmation
Continuous cast
Packaged to your needs
Shipped from inventory
Cu53-MBCu
Remainder
Zn
7.0 to 9.0%
Ni
14.0 to 16.0%
Mn Total otherelements
23.0 to 25.0% 0.35% Maximum
Section 1 — Brochure/Flier Marketing
8
PTC Alloys from Concast
w w w . c o n c a s t . c o m
Concast Metal Products Co. manufactures a wide range of copper alloys specifically engineered for the power transmission and control industry. These alloys support the market requirements for power transmission and control end-use applications.
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certified
Power Transmission and Control Applications
Linear Drives and Gears
Production Equipment
Bearings
Hydraulics
Compressed Air
Standard-stocked alloysC86300 | C90300 | C93200 | C95400 | C95500
Other available alloysC90700 | C91100 | C92900 | C93700 | C93800
Section 2 — Brochure/Flier Marketing: Updated
9
Call us today at 800.626.7071 or email us
at [email protected] to find out how we
can improve the reliability and profitability
of your wrought alloy supply chain.
500 Series Wrought-Drawn Alloys
At Concast Metal Products Co., we provide our customers a high-quality, reliable supply of 500 series wrought-drawn alloys (including 510, 521, 534 and 544) and an on-demand inventory of finished goods.
• Concast stocks 510 and 544 alloys as standard-stocked products.
• Concast offers you a “Made in the U.S.A.” source of supply.
• Concast works to continually improve consistency, increase yields and extend tool life.
Concast Is the Only Domestic Producer of Phosphor Bronze
P.O. Box 816 | Mars, PA 16046
800.626.7071 | 724.538.3956 fax
All Concast plants are ISO 9001:2008 certified�
500 Series Wrought-Drawn Alloys
CDA ASTM PRODUCT DESCRIPTION
*standard-stocked alloys
C51000*
C52100
C53400
C54400*
B139
B139
B139
B139
Phosphor Bronze
Phosphor Bronze
Phosphor Bronze
Phosphor Bronze
Call us today at 800.626.7071 or email us
at [email protected] to find out how we
can improve the reliability and profitability
of your wrought alloy supply chain.
C67300 Wrought-Drawn Alloy
At Concast Metal Products Co., we provide our customers a high-quality, reliable supply of C67300 and an on-demand inventory of finished goods.
• Concast stocks 673 alloy as a standard- stocked product.
• Concast works to continually improve consistency, increase yields and extend tool life.
P.O. Box 816 | Mars, PA 16046
800.626.7071 | 724.538.3956 fax
All Concast plants are ISO 9001:2008 certified�
Typical Uses
CATEGORY PRODUCT
Fasteners
Industrial
Marine
Other
fasteners, lead screw nuts
bearings, bushings, drive shafts, gears/cams, idler pins, piston heads, propeller shafts, pump parts, seal rings, shaft bushings, sleeve bearings, spindles, thrust bearings, wear plates, clutch bearings
hardware, valve seats
connecting rods
C673 Manganese Bronze Offers Exceptional Strength, Wear and Corrosion Resistance
Section 2 — Brochure/Flier Marketing: Updated
10
Alloy Cu% Sn% Pb% Zn% Fe% Ni% Sb% P% S% Al% Mn% Si% Bi%
85.00- 6.00- 2.00- 1.75-C89835 89.00 7.50 0.05 4.00 0.20 1.002 0.35 0.10 0.08 0.005 0.005 2.75
86.00- 7.50- 3.00- C90300 89.001 9.00 0.30 5.00 0.20 1.002 0.20 0.053 0.05 0.005 0.005
3.00- 10.00- C95400 83.00 5.00 1.502 11.50 0.50
3.00- 10.00- C95400HT 83.00 5.00 1.502 11.50 0.50
3.00- 3.00- 10.00- C95500 78.00 5.00 5.501 11.50 3.50
3.00- 3.00- 10.00- C95500HT 78.00 5.00 5.501 11.50 3.50
3.00- 12.00- C95900 Rem. 5.00 0.501 13.50 1.50
Lead-Free Replacement Product LineChemical Composition (Standard-Stocked Lead-Free Replacement Alloys)
1In determining Cu min., Cu may be calculated as Cu + Ni. 2Ni value includes Co. 3For continuous castings, P shall be 1.5%, max. 4Also, Se value of 0.8-1.1%Note: Single values represent maximums.
Chemical Composition (Other Lead-Free Replacement Alloys)
Alloy Cu% Sn% Pb% Zn% Fe% Ni% Sb% P% S% Al% Mn% Si% Bi%
87.00- 5.0- 4.0-C89320 91.00 7.0 0.09 1.00 0.10 1.002 0.35 0.30 0.08 0.005 0.005 6.0
84.00- 9.0- 2.70-C89325 88.00 11.0 0.10 1.00 0.15 1.002 0.50 0.10 0.08 0.005 0.005 3.70
85.00- 5.0- 4.00- 2.70-C895204 87.00 6.0 0.25 6.00 0.20 1.00 0.25 0.05 0.08 0.005 0.005 3.70
87.00- 2.70- 2.00- 2.70-C89831 91.00 3.70 0.10 4.00 0.30 1.002 0.25 0.05 0.08 0.005 0.005 3.70
86.00- 4.00- 2.00- 1.70-C89833 91.00 6.00 0.09 4.00 0.03 1.002 0.25 0.05 0.08 0.005 0.005 2.70
84.00- 3.00- 6.00- 0.70-C89837 88.001 4.00 0.10 10.00 0.30 1.002 0.25 0.05 0.08 0.005 0.005 1.20
83.00- 3.00- 7.00- 2.0-C89844 86.00 5.00 0.20 10.00 0.30 1.002 0.25 0.05 0.08 0.005 0.005 4.0
86.00- 9.00- 1.00- C90500 89.001 11.00 0.30 3.00 0.20 1.002 0.20 0.303 0.05 0.005 0.005
88.00- 10.00- C90700 90.001 12.00 0.50 0.50 0.15 0.502 0.20 0.303 0.05 0.005 0.005
85.00- 11.00- C90800 89.001 13.00 0.25 0.25 0.15 0.502 0.20 0.303 0.05 0.005 0.005 0.005
11.00- 0.15- C90810 Rem.1 13.00 0.25 0.30 0.15 0.502 0.20 0.803 0.05 0.005 0.005
84.00- 14.00- C91000 86.001 16.00 0.20 1.50 0.10 0.802 0.20 0.053 0.05 0.005 0.005
79.00- 18.00- C91300 82.001 20.00 0.25 0.25 0.25 0.502 0.20 1.03 0.05 0.005 0.005
Call us today at 800.626.7071 or email us at
[email protected] to find out how we can
improve the reliability and profitability of your
lead-free replacement alloy supply chain.
Lead-Free Replacement Alloys
Concast Metal Products Co. manufacturers a broad selection of lead-free replacement alloys for pipes, fittings, faucets and other plumbing components.
Lead-Free Replacementas Alloys Have Extremely Low-Lead Content, Some as Low as .05%
P.O. Box 816 | Mars, PA 16046
800.626.7071 | 724.538.3956 fax
All Concast plants are ISO 9001:2008 certified�
Lead-Free Replacement Alloys
STANDARD-STOCKED ALLOYS
C89835 C90300 C95400 C95500 C95900
C89320 C89325 C89520 C89831 C89833
C89837 C89844 C90500 C90700 C90800
C90810 C91000 C91300
OTHER AVAILABLE ALLOYS
Concast Metal Products Co.:
• offers you a “Made in the U.S.A.” source of supply.
• works to continually improve consistency, increase yields and extend tool life.
Section 2 — Brochure/Flier Marketing: Updated
11
Call us today at 800.626.7071 or email us at
[email protected] to find out how we can
improve the reliability and profitability of your
lead-free replacement alloy supply chain.
C89835 Lead-Free Replacement Alloy
Concast Metal Products Co. is now offering more than 100 sizes of C89835, a lead-free C932 replacement, as a standard-stocked inventory item. This alloy is also a suitable replacement for C836 and C844.
Concast Metal Products Co.:
• stocks C89835 as a standard-stocked product.
• supports the market demand for lead-free material.
• provides C89835 as an alloy compliant with the 3874 Reduction of Lead in Drinking Water Act.
• offers you a “Made in the U.S.A.” source of supply.
• works to continually improve consistency, increase yields and extend tool life.
C89835 has a maximum lead content of 0.05%
P.O. Box 816 | Mars, PA 16046
800.626.7071 | 724.538.3956 fax
All Concast plants are ISO 9001:2008 certified�
In Stock Now
Tubes and Solids
Sizes 1.0" to 4.0" OD
Call Mill for Other Sizes
C89835 Lead-Free Replacement Alloy
Section 3 — Email Marketing
12
Start 2015 with improved reliability, accessibility and profitability in your wrought alloy supply chain.
500 SeriesWrought-Drawn Alloys
What will you do differently in 2015? At Concast Metal Products Co., we believe the best plan begins with a reliable, consistent and on-demand supply base. Consider how our high-quality supply of 500 series wrought-drawn alloys and standard-stocked inventory of 510 and 544 finished goods can change the game for your business this year. Then give us a call.
Concast Is the Only Domestic Producer of Phosphor Bronze.
C51000 | C52100 | C53400 | C54400500 Series Alloys From Concast
w w w . c o n c a s t . c o m
Do you have the resources you
need to meet your goals in 2015?
or email us at
Call us today at
800.626.7071or email us at
Call us today at
800.626.7071
C89835 has a maximum lead content of 0.05% and is a suitable
replacement for C932, C836 and C844
Alloy C89835
Tubes | SolidsSizes 1.0″ to 5.0″
w w w . c o n c a s t . c o m
There’s no LEAD in leader! Concast is the industry leader for LEAD-FREE replacement alloys.
Compliant with the 3874 Reduction of Lead in Drinking Water Act
We provide more than 100 sizes of C89835as standard-stocked items
Concast fully supports the market demand for lead-free material
Find out how we can improve the reliability and profitability of your lead-free replacement alloy supply chain.
Lead-FreeReplacement Alloys
Concast Metal Products Co. manufactures a broad selection of lead-free replacement alloys for pipes, fittings, faucets and other plumbing components.
These products have extremely low-lead content,
some as low as .05%.
Concast is the industry leader for lead-free replacement alloys.
Standard-Stocked Lead-Free Replacement Alloys
w w w . c o n c a s t . c o m
C89835 | C90300 | C95400 | C95500 | C95900
or email us at
Call us today at
800.626.7071or email us at
Call us today at
800.626.7071
Let Concast provide you with improved reliability, accessibility and profitability
in your wrought alloy supply chain.
Wrought Products
C31400 | C51000 | C54400 | C63000 | C64200Standard-Stocked Wrought Alloys
C31600 | C52100 | C53400 | C65100Other Wrought Alloys
w w w . c o n c a s t . c o m
Improved Size and ConsistencyIncreased Mechanical PropertiesImproved Machinability and Productivity
Concast Metal Products Co. means:
At Concast Metal Products Co., we believe the best plan begins with a reliable, consistent and on-demand supply base.
Section 4 — Postcard Marketing
13
Concast Metal Products Co.14315 State Route 113Birmingham, OH 44816
Alloy C630 is a Concast Standard-Stocked Alloy
www.concast .com800.626.7071 | 724.538.3956 fax
P.O. Box 816 | Mars, PA 16046
[email protected] All Concast plants are ISO 9001 certified
C63000 Alloy Chemical Composition
C63000 Remainder0.20 0.30
4.00- 9.00- 0.00-0.255.50 11.00 1.50
Alloy Cu% Sn% Pb% Zn%
2.00-4.00
Fe% Ni% AL% Mn% Si%
C63000 Alloy Similar or Equivalent SpecificationCDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER
C63000 B150 J461 4640 QQ-C-465B AMD1J463
Alloy C630 from Concast
Alloy C630 is a Concast Standard-Stocked Alloy
www.concast .com800.626.7071 | 724.538.3956 fax
P.O. Box 816 | Mars, PA 16046
[email protected] All Concast plants are ISO 9001 certified
SpecificationsCDA
C63000
ASTM
B150
AMS
4640
Concast is the only domestic producer of alloy C63000. This nickel-aluminum bronze alloy combines corrosion resistance, excellent bearing properties at considerable loads and extremely high strength at a wide range of temperatures.
Industrial Applications
Valve Seats | Plunger Tips | Shafting
Pump Parts | Cams | Gears
Condenser Tube for Power Stations and Desalting Units
Pump Shafts | Structural Members
Aircraft Parts | Valve Balls | Headers
Corrosion-Resistant Articles | Bushings
Hydraulic Bushings for Earth-Moving Equipment
Heat Exchanger Flanges | Heat Exchanger
Bearings | Tanks | Valve Guides
Marine Applications
Nuts | Ship Propellers | Pump Parts
Bolts | Propellers
Plumbing Applications
Faucets | Water-Handling Equipment
Section 4 — Postcard Marketing
14
Concast Metal Products Co.14315 State Route 113Birmingham, OH 44816
Alloy C642 is a Concast Standard-Stocked Alloy
www.concast .com800.626.7071 | 724.538.3956 fax
P.O. Box 816 | Mars, PA 16046
[email protected] All Concast plants are ISO 9001:2008 certified
C64200 Alloy Chemical Composition
C64200 Remainder
Alloy Cu% Al%
0.09
As%
0.30
Fe%
0.05
Pb%
0.10
Mn%
0.25
Ni% Si%
0.20
Sn%
0.50
Zn%
C64200 Alloy Similar or Equivalent Specification
6.30-7.60
1.50-2.20
CDA ASTM ASARCON SAE AMS FEDERAL MILITARY OTHER
C63000 B150 J461 4631 QQ-C-465B AMD1J463
Alloy C642 from Concast
Alloy C642 is a Concast Standard-Stocked Alloy
www.concast .com800.626.7071 | 724.538.3956 fax
P.O. Box 816 | Mars, PA 16046
[email protected] All Concast plants are ISO 9001:2008 certified
SpecificationsCDA
C64200
ASTM
B150
AMS
4631
Our C64200 aluminum bronze
alloy is used in the power
generation & energy, aerospace
and automotive markets and
industrial applications.
Automotive
Valve Guides | Automobile Engines
Electrical
Pole Line Hardware
Fasteners
Nuts | Bolts
Industrial
Valve Bodies | Valve Stems | GearsCams | Valve Components
Marine
Hardware
Section 4 — Postcard Marketing
15
Concast Metal Products Co.14315 State Route 113Birmingham, OH 44816
www.concast .com800.626.7071 | 724.538.3956 fax
P.O. Box 816 | Mars, PA 16046
[email protected] All Concast plants are ISO 9001 certified
Aerospace-Related Products
CDAC51000*
C63000*
C64200*
C86300*
C86500
C90300*
C90500
C90700*
C93700
C94100
C94300
C95400*
C95500*
C95510
ASTMB139
B150
B150
B505
B505
B505
B505
B505
B505
B505
B505
B505
B505
—
AMS4625
4640
4634B
4862
4860
—
4845
—
4842
—
—
—
—
4880
*standard stocked alloys
Aerospace and Concast
Concast is a manufacturer of specialty continuous cast copper alloys. Our primary focus is the production of copper alloys in bars, rods, tubes and rectangles, as well as custom alloys and wrought drawn products. All products are produced with state-of-the-art horizontal and vertical continuous- casting technology.
We offer our customers a wide range of wrought drawn alloys, including C510 phosphor bronze, C630 nickel-aluminum bronze and C642 aluminum bronze.
www.concast .com800.626.7071 | 724.538.3956 fax
P.O. Box 816 | Mars, PA 16046
[email protected] All Concast plants are ISO 9001:2008 certified
Benefits of Continuous Cast:
Uniform structures(eliminates hard spots)
Favorable mechanical properties
Greater friction and wear properties
Excellent machinability and fabrication ability
Reasonable cost
Section 4 — Postcard Marketing
16
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 faxwww.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certifi ed
Concast offers a complete line of stocked and custom-made products. When Concast
customers request special alloys and special sizes, we respond with products designed
to meet their exacting specifications.
Special Alloys Available Upon Request
� Continuous Cast Products
C86300 Manganese Bronze
C89835 Bismuth Tin Bronze
C90300 High Tin Bronze
C93200 Leaded Tin Bronze
C95400 Aluminum Bronze
C95500 Nickel Aluminum Bronze
C95900 Aluminum Bronze
(All above alloys are standard-stocked items)
� Wrought Drawn Products
C31400 Leaded Commercial Bronze
C46400 Naval Brass
C51000 Phosphor Bronze
C54400 Phosphor Bronze
C63000 Nickel Aluminum Bronze
C64200 Aluminum Bronze
C67300 Manganese Bronze
(All above alloys are standard-stocked items)
Cast Products Wrought Products
AlloyProduct
Description
*standard-stocked alloys
C31400*
C31600
C51000* C52100 C53400 C54400* C63000*
C64200*
C65100
Leaded Commercial Bronze
Leaded Commercial Bronze (Nickel-Bearing)
Phosphor Bronze 5% A
Phosphor Bronze 8% C
Phosphor Bronze B-1
Phosphor Bronze B-2
Nickel Aluminum Bronze(AMS 4640)
Aluminum Bronze(AMS 4634B)
Low-Silicon Bronze B
AlloyProduct
Description
C83600 Leaded Red Brass
C86300* Manganese Bronze
C86500 Manganese Bronze
C89835* Bismuth Tin Bronze
C90300* High Tin Bronze
C90500 Tin Bronze
C90700 Tin Bronze
C91100 Tin Bronze
C92900 Leaded Nickel Tin Bronze
C93200* Leaded Tin Bronze
C93700 High-Leaded Tin Bronze
C93800 High-Leaded Tin Bronze
C94100 High-Leaded Tin Bronze
C94300 High-Leaded Tin Bronze
C95400* Aluminum Bronze
C95500* Nickel Aluminum Bronze
C95900* Aluminum Bronze
*standard-stocked alloys
Concast Metal Products Co.14315 State Route 113Wakeman, OH 44889
P.O. Box 816 | Mars, PA 16046800.626.7071 | 724.538.3956 fax
www.concast.com | [email protected]
All Concast plants are ISO 9001:2008 certifi ed
Contact Us for Other Alloys
Section 5 — Postcard Marketing: Updated
17
Concast Metal Products Co.14315 State Route 113Wakeman, OH 44889
w w w . c o n c a s t . c o m
P.O. Box 816 | Mars, PA 16046 | 800.626.7071
CDA
C51000*
C52100
C53400
C54400*
ASTM
B139
B139
B139
B139
Product Description
Phosphor Bronze
Phosphor Bronze
Phosphor Bronze
Phosphor Bronze
*standard stocked alloys
500 SERIES Wrought-Drawn Alloys
w w w . c o n c a s t . c o m
500 SeriesWrought-Drawn Alloys
� All Concast plants are ISO 9001:2008 certifiedP.O. Box 816 | Mars, PA 16046
Concast Is the Only Domestic Producer of Phosphor Bronze
� Concast produces 510, 521, 534 and 544 alloys.
� Concast stocks 510 and 544 alloys as standard-stocked products.
� Concast offers you a “Made in the U.S.A.” reliable source of supply.
Section 5 — Postcard Marketing: Updated
18
w w w . c o n c a s t . c o m
P.O. Box 816 | Mars, PA 16046 | 800.626.7071
Concast Metal Products Co.14315 State Route 113Wakeman, OH 44889
WROUGHT PRODUCTSCDA
C31400*
C31600
C46400*
C51000*
C52100
C53400
C54400*
C63000*
C64200*
C65100
C67300*
ASTM
B140
B140
B21
B139
B139
B139
B139
B150
B150
B98
—
Product Description
Leaded Commercial Bronze
Leaded Commercial Bronze (nickel-bearing)
Naval Brass
Phosphor Bronze
Phosphor Bronze
Phosphor Bronze
Phosphor Bronze
Nickel Aluminum Bronze
Aluminum Bronze
Low-Silicon Bronze
Manganese Bronze
*standard stocked alloys
w w w . c o n c a s t . c o m
Wrought Productsfrom Concast
Improved Size and ConsistencyIncreased Mechanical Properties
Improved Machinability and Productivity
Our wrought products are brought to final dimensions by one or more cold drawing
operations with suitable intermediate anneals when
necessary. After the final draw, the rods are
straightened mechanically and
cut to the desired length.
P.O. Box 816 | Mars, PA 16046 � All Concast plants are ISO 9001:2008 certified
Section 6 — Trade Show Banners
19
Oil & Gas Applications
Oil & Gas Industry and Concast
The demanding applications of the oil & gas industry are supported with alloys manufactured by
Concast Metal Products Co.
� Bearings
� Bushings
� Hydraulic seals
� Seals
� Torque plugs
� Pump parts
All Concast plants are ISO 9001:2008 certified
Oil & gas industry alloys
Oil & Gas Alloys from Concast
All Concast plants are ISO 9001:2008 certified
C63000 | C86300 | C93200 | C95400
C95400HT | C95410 | C95500 | C95500HT
C95520HT | C95800
Concast Metal Products Co.manufactures a wide range of copper alloys specifically engineered for oil & gas applications.
Aerospace and Concast
All Concast plants are ISO 9001:2008 certified
Standard-stocked alloys
C51000 | C63000 | C86300 | C90300 | C90700C95400 | C95500
Other available alloys
C86500 | C90500 | C93700 | C94100C94300 | C95510
Benefits of Continuous Cast:
Material Description:
• Uniform structures (eliminates hard spots)
• Favorable mechanical properties
• Greater friction and wear properties
• Excellent machinability andfabrication ability
• Reasonable cost
• Aluminum bronze• Manganese bronze• High tin bronze
• High-leaded tin bronze• Phosphor bronze rods• Nickel-aluminum bronze
Section 7 — Trade Show Banners: Updated
20
Applications
Faucets | Pump Components | Pipe Fittings
Plumbing Components | Water Pump Impellers
C89835 Alloy from Concast
� Standard-Stocked Alloy
� 90 Available Sizes
� Lead-Free Replacement for C932, C836 and C844
C89835 is compliant with key legislation including (1) Federal Safe Drinking Water Act 1974 – SDWA, (2) Federal Reduction of Lead in Drinking Water Act 2011 and (3) California AF1953.
All Concast plants are ISO 9001:2008 certified
Lead-Free Replacement Alloys
All Concast plants are ISO 9001:2008 certified
Concast manufacturers a broad selection of lead-free replacement alloys for pipes, fittings, faucets and other plumbing components. These products have extremely low-lead content, some as low as .05%.
Standard-Stocked Alloys
Other Available Alloys
C89835 | C90300 | C95400 | C95500 | C95900
C87850 | C89320 | C89325 | C89520 | C89831 | C89833
C89837 | C89844 | C90500 | C90700 | C90800 | C90810
C91000 | C91300
Fire Protection Industry and Concast
All Concast plants are ISO 9001:2008 certified
Concast Metal Products Co. manufactures a wide range of alloys exhibiting the qualities of economy and versatility necessary for the construction of dependable fire sprinkler systems.
Fire Protection Industry Alloys
C31400 | C31600
� Sprinkler Components
� Tubing
� Joining Systems
� Pressure Fittings
Fire Protection Applications
Section 7 — Trade Show Banners: Updated
21
C63000 Alloy from Concast
� Satisfies a Broad Range of Applications
� Standard-Stocked Alloy
All Concast plants are ISO 9001:2008 certified
Industrial ApplicationsValve Seats | Plunger Tips | Valve Guides | Bearings
Aircraft Components | Shafting | Pump Parts
Cams | Gears | Valve Balls | Pump Shafts
Structural Members | Corrosion-Resistant Articles
Hydraulic Bushings for Earth-Moving Equipment
Bushings | Heat Exchanger Flanges | Headers
Heat Exchangers | Tanks | Welding Piping Systems
Condenser Tube for Power Stations and Desalting Units
Marine ApplicationsNuts | Propellers | Pump Parts | Bolts
C46400 Alloy from Concast
� Standard-Stocked Alloy
All Concast plants are ISO 9001:2008 certified
C46400, naval brass, is widely used in plumbing components where a strong, corrosion-resistantand hard material is required.
� Low Lead
Marine Applications
Decorative Fittings | Hardware | Propeller ShaftsShafting | Turnbuckles
Electrical Applications
Precision Shipboard Equipment
Plumbing Applications
Fittings
All Concast plants are ISO 9001:2008 certified
C64200 Alloy from Concast
� Standard-Stocked Alloy
C64200, aluminum bronze, is used in the power generation/energy, industrial applications, aerospace and automotive markets.
Industrial ApplicationsValve Bodies | Valve Stems | Gears | CamsValve Components | Aircraft Components
Automotive ApplicationsValve Guides | Automobile Engines
Electrical ApplicationsPole Line Hardware
Fastener ApplicationsNuts | Bolts
Marine ApplicationsHardware
Section 7 — Trade Show Banners: Updated
22
C67300 Alloy from Concast
� Standard-Stocked Alloy
All Concast plants are ISO 9001:2008 certified
C67300, manganese bronze, offers exceptional strength, wear and corrosion resistance.
Fastener ApplicationsFasteners | Lead Screw Nuts
Industrial ApplicationsBearings | Bushings | Drive Shafts | Gears/Cams
Idler Pins | Piston Heads | Propeller Shafts
Pump Parts | Seal Rings | Shaft Bushings
Sleeve Bearings | Spindles | Thrust Bearings
Wear Plates | Clutch Bearings
Marine ApplicationsHardware | Valve Seats
OtherConnecting Rods
Wrought Products from Concast
Standard-Stocked Alloys
Other Available Alloys
Concast Metal Products has been successfully satisfying a broad range of applications and industries with our wrought drawn alloys.
Reduces machining losses | Dimensional consistency within each bar
Improved Size and Consistency
Dimensional consistency from bar to bar | Tighter size/section tolerances
Increased Mechanical PropertiesYield and Tensile strength | Hardness (may reduce the need for hardening)
Improved Machinability and ProductivityAllows for higher feeds and speeds and improved machined finishIncreased machining rates | Longer tool life | Improved yield
C31400 | C46400 | C51000 | C54400 | C63000 | C64200
C31600 | C52100 | C53400 | C65100
All Concast plants are ISO 9001:2008 certified
Section 8 — Print Advertising: New Concepts
23
Your alloys supply chain should impress you … and your customers
www.concast.com | [email protected]
P.O. Box 816 | Mars, PA 16046 | 800.626.7071 | 724.538.3956 fax
Is the performance of your alloys supply chain something you are excited to share with your customers? If not, it is time to consider Concast Metal Products Co.
Established in 1891, Concast has earned a reputation for meeting customer requirements for reliability, availability and value across cast and wrought product lines.
We provide a wide range of high-quality and standard-stocked options that give our customers what they need … when they need it.
At Concast, we constantly challenge ourselves to understand our customers’ requirements and quickly respond with solutions to ensure that we remain their supplier of choice.
Your alloys supply chain should impress you … and your customers
Is the performance of your alloys supply chain something you are excited to share with your customers? If not, it is time to consider Concast Metal Products Co.
Established in 1891, Concast has earned a reputation for meeting customer requirements for reliability, availability and value across cast and wrought product lines.
We provide a wide range of high-quality and standard-stocked options that give our customers what they need … when they need it.
At Concast, we constantly challenge ourselves to understand our customers’ requirements and quickly respond with solutions to ensure that we remain their supplier of choice.
P.O. Box 816 | Mars, PA 16046 | 800.626.7071 | 724.538.3956 fax
www.concast.com | [email protected]
Section 8 — Print Advertising: New Concepts
24
Concast provides reliability, accessibility andprofitability in your wrought alloy supply chain.
� Improved Size and Consistency
� Enhanced Surface Finish
� Increased Mechanical Properties
� Improved Machinability and Productivity
www.concast.com | [email protected]
P.O. Box 816 | Mars, PA 16046 | 800.626.7071 | 724.538.3956 fax
Standard-Stocked Wrought Drawn Alloys
C31400 | C46400 | C51000 | C54400C63000 | C64200 | C67300
Our wrought products are cast and cold drawn. Rods are brought to final dimensions by one or more cold drawing operations with suitable intermediate anneals when necessary.
Concast provides reliability, accessibility andprofitability in your wrought alloy supply chain.
� Improved Size and Consistency
� Enhanced Surface Finish
� Increased Mechanical Properties
� Improved Machinability and Productivity
www.concast.com | [email protected]
P.O. Box 816 | Mars, PA 16046 | 800.626.7071 | 724.538.3956 fax
Standard-Stocked Wrought Drawn Alloys
C31400 | C46400 | C51000 | C54400C63000 | C64200 | C67300
Our wrought products are cast and cold drawn. Rods are brought to final dimensions by one or more cold drawing operations with suitable intermediate anneals when necessary.
Section 8 — Print Advertising: New Concepts
25
Concast is the industry leader for lead-free replacement alloys.
Concast Metal Products Co. manufactures a broad selection of lead-free replacement alloys for pipes, fittings, faucets and other plumbing components.
These products have extremely low-lead content, some as low as .05%.
www.concast.com | [email protected]
Standard-Stocked Lead-Free Replacement Alloys
C89835 | C90300 | C95400 | C95500 | C95900
P.O. Box 816 | Mars, PA 16046 | 800.626.7071 | 724.538.3956 fax
Concast is the industry leader for lead-free replacement alloys.
Concast Metal Products Co. manufactures a broad selection of lead-free replacement alloys for pipes, fittings, faucets and other plumbing components.
These products have extremely low-lead content, some as low as .05%.
www.concast.com | [email protected]
Standard-Stocked Lead-Free Replacement Alloys
C89835 | C90300 | C95400 | C95500 | C95900
P.O. Box 816 | Mars, PA 16046 | 800.626.7071 | 724.538.3956 fax