1
MEMBER OF CMB GROUP
IT’S WHAT’S UNDERNEATH THAT COUNTS.
MARMOX Board PRO / ULTRA – Tile Backer Boards
ContentsMARMOX
1. Introduction
2. MARMOX Board PRO
3. MARMOX Board ULTRA
4. Installation
5. MARMOX Board PRO / ULTRA - Pipe Boxing
6. MARMOX Board PRO / ULTRA - Flex
7. MARMOX Board PRO / ULTRA - Bath- and Shower Basin Panel
8. MARMOX Board PRO / ULTRA - Toiletbox / Installation Panel
9. MARMOX Board PRO - Underfloor Heating
10. Accessories
MARMOX Board – Tile Backer Boards
4
8
12
16
20
22
24
26
28
30
3
We serve globallyWhen building or renovating your home, the use of tiles, marble or
mosaic provides it with a personal touch. Much attention is paid to
a careful choice of colours, dimensions, and the installation itself.
However, all those efforts could prove in vain if stress from outside
(such as temperature changes, sun, frost, moisture or mechanical
stress) cause the delamination of the adhesive, destroying the sub-
construction.
In fact: “It’s what’s underneath that counts”
MARMOX Board is the all-in-one solution for waterproofing,
insulating and dry-lining. It is lightweight, easy to cut, and can be
applied to floors, walls and ceilings as a ready-to-use surface for
tiles or plaster.
Using MARMOX Board - solutions will give you the reassurance that
your finishing will be durably protected and stable.
Sustainability
Our factory operates a zero waste policy where all waste material
from MARMOX Board PRO / ULTRA production is recycled into other
less formulation critical products. MARMOX Board PRO / ULTRA
does not contain any VOC or emit any dangerous substances.
ODP (ozone depletion potential) = zero
GWP (global warming potential) = 0,29
PREAMBLE
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
4
MARMOX Board – Tile Backer Boards
5
1. IntroductionMARMOX Board – Tile Backer Boards are made of XPS-foam with glass fibre
reinforced cement coating. The special XPS-benefit is that its thermal insulation
properties are not affected whatsoever by wet or damp conditions. So the boards are
resistant against water, moisture and humidity and they are non-capillary, light weight
and easy to cut - ideal prerequisites for multi-purpose application, especially in wet
room areas.
MARMOX Board – Tile Backer Boards are recommended for use on walls, floors, and to
build or insert wash tables, shelves, claddings, insulations under electric heating wires or
partition walls. The options to use the boards are wide and creative.
The surface of MARMOX Board– Tile Backer Boards is suitable for the application
of tiles, mosaic, natural stone, plasters or putties. The boards allow a quick, easy, and
creative construction without or reduced drying time.
MARMOX BOARD – TILE BACKER BOARDS
Applications:
· on walls and floors
· partition walls
· bath and shower base panels
· pipe box
· toilet box and installation panel
· wash table, shelf
· bench, lounger, Hamam (bath room)
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
6
1.1. Composition
Composition of MARMOX Board - Tile Backer Boards
MARMOX Board - Tile Backer Boards are made from CFC- and HCFC-free extruded
polystyrene foam (XPS). The closed cell structure of XPS-foam is water-resistant with
good insulation properties.
MARMOX Board PRO
The surfaces of MARMOX Board PRO are covered from both sides with an alkali-
resistant glass fibre mesh embedded in polymerised cement mortar. A newly developed
production technology ensures an excellent embedding of the reinforcing glass fibre
mesh in the special cement mortar. The characteristic honey comb finishing is the
outstanding feature of the very strong and professional MARMOX Board PRO. The
mechanical properties of MARMOX Board PRO, such as compressive strength, improved
bonding strength and shear strength, are some of the best in the market.
MARMOX Board ULTRA
MARMOX Board ULTRA are made of extruded polystyrene foam boards, covered on
both sides with special polymeric cement mortar, reinforced with alkali resistance glass
fiber mesh providing a very special surface texture which ensures a good adhesion to
tile adhesive. The extruded polystyrene foam boards are CFC, HCFC and HBCD free. The
boards are tough, extra light weight and water resistant. The surface is ready for tiling.
The main advantage of MARMOX Board ULTRA is the extraordinary light weight and
water vapor proofing properties. The boards are suitable for use as a substrate for tiles
in dry as well as wet areas and very humid rooms. The boards are water impermeable
and heat insulating. They are very easy to cut and to use and simple to install.
7
Product Thickness Length Width
mm mm mm
MARMOX Board 4 4 1.250 / 1.300 600
MARMOX Board 6 6 1.250 / 1.300 600
MARMOX Board 10 10 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 12,5 12,5 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 20 20 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 30 30 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 40 40 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 50 50 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 60 60 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 80 80 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
MARMOX Board 100 100 1.250 / 1.300 / 2.500 / 2.600 600 / 900 / 1.200
Other dimensions are also available upon request.
1.2. Dimensions
Dimensions of MARMOX Board PRO and MARMOX Board ULTRA
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
8
MARMOX Board PRO are characterised by their honey comb surface finishing. This new innovative
finishing provides significant enhanced properties:
2. MARMOX Board PROMARMOX BOARD – TILE BACKER BOARDS
honey comb surface finishing
9
The glass fibre mesh is fully embedded in special cement mortar, covering the mesh
completely, in order to optimise the absorption of mechanical strengths. Due to that
MARMOX Board PRO are characterized by excellent mechanical properties.
Improved bonding strength of tile adhesive.
Increased maximum shear force bond of MARMOX Board PRO. The working load
of the MARMOX Board PRO reached more than 60 kg/m2 in vertical position,
if a polymer glue will be used.
Increased bending tensile bond strength.
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
cement mortar
cement mortar
alkali-resistant glass fibre mesh
alkali-resistant glass fibre mesh
XPS-foam
10
2.1. Technical Properties
of MARMOX Board PRO
Grammage of MARMOX Board PRO:
Property Standard / Norm Result
grammage (tol.: +/- 10%):
MARMOX Board PRO 4 3.60 kg/m²
MARMOX Board PRO 6 3,70 kg/m²
MARMOX Board PRO 10 3,90 kg/m²
MARMOX Board PRO 12,5 4,00 kg/m²
MARMOX Board PRO 20 4,25 kg/m²
MARMOX Board PRO 30 4,60 kg/m²
MARMOX Board PRO 40 4,95 kg/m²
MARMOX Board PRO 50 5,30 kg/m²
MARMOX Board PRO 80 6,40 kg/m²
compressive strength with 10% deflection: DIN EN 826
MARMOX Board PRO 50 4,4 kN/m²
water absorption after long term immersion: DIN EN 12087
MARMOX Board PRO 12,5 <4,4 Vol%
MARMOX Board PRO 20 <3,7 Vol%
MARMOX Board PRO 30 <2,7 Vol%
MARMOX Board PRO 40 <1,9 Vol%
fire property DIN EN 13501-1 E*
range of temperature - 50°C - +75°C
tolerances length ± 2 mm
width ± 2 mm
thickness ± 1 mm
*tested on MARMOX Board PRO with 50 mm thickness
11
Property Standard / Norm Result
raw density DIN EN 1602 >30 kg/m³
heat conductivity after 5 years DIN EN 13164 0,034 W/mK
compressive strength with 10% deflection DIN EN 826 300 kN/m²
water absorption after long term immersion DIN EN 12087 <1,0 Vol%
capillarity zero
Thermal transmission coefficient / thermal resistance
of MARMOX Board PRO:
Product U-Value [W/(m²K)] R-Value [(m²K)/W]
MARMOX Board PRO 4 4,25 0,24
MARMOX Board PRO 6 3,42 0,29
MARMOX Board PRO 10 2,46 0,41
MARMOX Board PRO 12,5 2,09 0,48
MARMOX Board PRO 20 1,44 0,69
MARMOX Board PRO 30 1,02 0,98
MARMOX Board PRO 40 0,79 1,26
MARMOX Board PRO 50 0,65 1,55
MARMOX Board PRO 60 0,54 1,84
MARMOX Board PRO 80 0,42 2,41
MARMOX Board PRO 100 0,34 2,98
declaration of performance (CE):
XPS – EN13164 – T1 – CS(10\Y)400 – CC(2/1/10)115 – WL(T)3)
Technical properties XPS-Polystyrene-foam:
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
12
A special feature of MARMOX Board ULTRA is the new coating structure, based on a
polymer-cement composition with fibreglass mesh. The new feature makes the board lighter
and more stiff than the MARMOX Board PRO.
3. MARMOX Board ULTRAMARMOX BOARD – TILE BACKER BOARDS
13
polymeric cement mortar
polymeric cement mortar
alkali-resistant glass fibre mesh
alkali-resistant glass fibre mesh
XPS-foam
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
The surfaces of MARMOX Board ULTRA are using a specially modified polymer - cement
mortar reinforced with an alkali-resistant fiberglass mesh, coated.
The specially modified coating and the selected materials result in a direct comparison
with MARMOX Board PRO advantages that greatly simplify the handling and processing of
MARMOX Board ULTRA:
significant weight reduction
MARMOX Board ULTRA is noticeably stiffer
easier cutting
again reduced water absorption
14
3.1. Technical Properties
of MARMOX Board ULTRA
Grammage of MARMOX Board ULTRA
Property Test / Norm Result
grammage (tol.: +/- 10%):
MARMOX Board ULTRA 4 1,30 kg/m²
MARMOX Board ULTRA 6 1,35 kg/m²
MARMOX Board ULTRA 10 1,50 kg/m²
MARMOX Board ULTRA 12,5 1,55 kg/m²
MARMOX Board ULTRA 20 1,80 kg/m²
MARMOX Board ULTRA 30 2,10 kg/m²
MARMOX Board ULTRA 40 2,40 kg/m²
MARMOX Board ULTRA 50 2,70 kg/m²
MARMOX Board ULTRA 80 2,75 kg/m²
15
Property Test / Norm Result
raw density DIN EN 1602 >30 kg/m³
heat conductivity after 5 years DIN EN 13164 0,034 W/mK
compressive strength with 10% deflection DIN EN 826 300 kN/m²
water absorption after long term immersion DIN EN 12087 <1,0 Vol%
capillarity zero
fire property DIN EN 13501-1 E
Technical properties XPS-Polystyrene-foam:
Thermal transmission coefficient / thermal resistance
of MARMOX Board ULTRA:
Product U-Value [W/(m²K)] R-Value [(m²K)/W]
MARMOX Board ULTRA 4 3,73 0,27
MARMOX Board ULTRA 6 3,07 0,33
MARMOX Board ULTRA 10 2,27 0,44
MARMOX Board ULTRA 12,5 1,96 0,51
MARMOX Board ULTRA 20 1,38 0,73
MARMOX Board ULTRA 30 0,99 1,01
MARMOX Board ULTRA 40 0,77 1,30
MARMOX Board ULTRA 50 0,63 1,58
MARMOX Board ULTRA 60 0,54 1,87
MARMOX Board ULTRA 80 0,41 2,44
MARMOX Board ULTRA 100 0,33 3,01
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
16
MARMOX Board PRO / ULTRA is very easy to install on floors provided that the
underground is prepared to be flat, rigid and clean. A complete embedding of the boards
without hollow spaces is required if the boards are used on floors. The boards should be
installed in a staggered pattern. An additional mechanical fixing of the boards is possible
and we recommend use of 5 nails/screws per m².
MARMOX Board PRO / ULTRA is suitable for installation on metal and timber frame walls
as well as on brick and concrete walls. It is preferable to install the long side of the board
vertically in a staggered pattern. The fastening can be done using screws and/or glue,
either applied complete or partial. All available thicknesses of MARMOX Board PRO /
ULTRA are suitable for wall application. Boards of 4 mm and 6 mm thickness need to be
glued completely without hollows on a stable substrate.
MARMOX Board PRO / ULTRA
MARMOX Board PRO / ULTRA
MARMOX Board PRO / ULTRA
reinforcing mortar
filling mortar
sub-structure
flexible cement mortar with glass fibre mesh reinforcement
nailed dowel
hollow wall anchor
4.1. Installation of accessories
Exemplary installation of dowels:
Installation for light weight with hollow wall anchor (e.g. soap dish)
Installation for more heavy loads (e.g. towel rail)
Light installations Installation for more heavy loads
4. InstallationMARMOX BOARD – TILE BACKER BOARDS
MARMOX Board PRO / ULTRA is suitable for installation on walls and floors.
17
4.2. Installation on floors
General steps for the installation of MARMOX Board PRO / ULTRA
on concrete floors
01. The substrate should be levelled, oil and dust free, dry and stable. If necessary, a
primer can be applied.
02. We recommend using a flexible cement-based tile adhesive, combed out with a
10 mm trowel, creating a ribbed adhesive bed. The boards have to be fully bedded
to ensure no void under them.
03. Align the boards vertically and horizontally in a staggered pattern.
04. When the adhesive is cured, apply the glass fibre mesh to the joints, embedded into
flexible tile adhesive.
General steps for the installation of MARMOX Board PRO / ULTRA
on timber floors
01. All MARMOX Board PRO / ULTRA with a minimum thickness of 10 mm is suitable to
be used on timber floors.
02. Timber floors must be dry, rigid, checked for flatness, oil and dust free.
03. The floor must be primed according to the manufacturers’ instructions before the
flexible cement adhesive can be applied with a notched trowel. The boards have to
be laid in a staggered pattern, fully bedded to ensure no voids under the boards.
04. When the adhesive is cured, apply fibre glass tape to the joints, embedded into
flexible tile adhesive.
05. After the flexible tile adhesive has dried, secure the boards with screws or nails and
washers at the rate of 5 fixings per sqm, close to the sides and in the middle of the
boards.
06. The floor is now prepared for the intended use.
tiles
timber floor
tile adhesive
tile adhesive
MARMOX Board PRO / ULTRA
Remark:
Please consider the official regulations
regarding waterproofing systems, if
required. An additional sealing system
might be required.
tiles
concrete floor
tile adhesive
tile adhesive
MARMOX Board PRO / ULTRA
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
18
MARMOX Board PRO / ULTRA on metal and timber frame walls
All MARMOX Board PRO / ULTRA with a minimum thickness of 10 mm is suitable for the
installation of frame walls. We recommend considering a studs distance of 300 mm
if MARMOX Board PRO / ULTRA with 10 mm or 12.5 mm will be used. A studs distance
of 600 mm is recommended if boards with 20 mm thickness or more are used.
Use galvanised or stainless steel or self-cutting screws with washers. The screws should
be at least 20 mm longer than the boards’ thickness.
Working steps:
01. Frame walls
02. Fixing with screws and covering of joints with glass fibre mesh or sealing tape,
embedded in a layer of flexible tile adhesive.
03. Once the adhesive has cured, tiles can be fixed and grouted.
04. Ready to use.
Remark:
Please consider official regulations
regarding waterproofing systems, if
required. An additional sealing system
might be required.
03 04
01 02
4.3. Installation on walls
19
01 02
03
MARMOX Board PRO / ULTRA on brick or concrete walls
For even, clean and sound walls, use flexible tile adhesive combed out with a notched
trowel. Then the boards are thoroughly bedded in a staggered pattern and aligned
vertically and horizontally.
An additional mechanical fixing with a rate of 5 screws per sqm is recommended if the
wall surface bonding capacity is weak and does not allow strong bonding. Cover all
joints with glass fibre mesh or sealing tape, embedded in a layer of flexible tile adhesive.
For uneven walls use Boards with 20 mm thickness or more. Drill the boards at the place
of dowels at the rate of 5 dowels per sqm. Place dabs of tile adhesive on the holes. The
boards have to be laid in a staggered pattern, aligned vertically and horizontally. Once
the tile adhesive has cured, drill the board through the holes into the wall and insert
dowels, washers and screws/nails. Cover all joints with glass fibre mesh or sealing tape,
embedded in a layer of flexible tile adhesive.
Installation steps:
01. Drill 5 holes per m² at the fixing points of boards, place dabs at the position of the
holes on the back side of the boards.
02. Align the boards vertically and horizontally in the right place.
03. Drill through the holes in the boards into the wall, insert dowels and arrange the
fixing with screws/nails.
04. Cover all joints with glass fibre mesh or sealing tape, embedded in a layer of flexible
tile adhesive.
04
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
20
21
MARMOX Board PRO / ULTRA - Pipe Boxing
5. MARMOX Board PRO / ULTRA - Pipe BoxingMARMOX Board - Pipe Boxing are ideal to cover pipes or for decoration such as trays
and shelves.
MARMOX BOARD – TILE BACKER BOARDS
Pre-fabricated pipe boxing saves considerable time at the job site.
Product Thickness Angle Length Length
mm mm mm
MARMOX Board PRO / ULTRA - pipe boxing 150/150 20 150 x 150 1.250 / 2.500
MARMOX Board PRO / ULTRA - pipe boxing 200/200 20 200 x 200 1.250 / 2.500
MARMOX Board PRO / ULTRA - pipe boxing 300/300 20 300 x 300 1.250 / 2.500
MARMOX Board PRO / ULTRA - pipe boxing 200/400 20 200 x 400 1.250 / 2.500
Other dimensions are available upon request.
Dimensions
Standard dimensions:
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
22
23
6. MARMOX Board PRO / ULTRA - FlexMARMOX Board - Flex are flexible boards designed to bend to the required curve ready for
mosaic tiling. The boards are created to make curved designs more achievable in a fast and
price competitive way.
MARMOX BOARD – TILE BACKER BOARDS
The flex boards are designed for curved coverings or partition walls, e.g. coverings of
whirlpools, round shower areas, and columns.
MARMOX Board - Flex are available with longitudinal and transversal cuts.
Product Cut Length Thickness Width Length
mm mm mm mm
MARMOX Board PRO / ULTRA - 20 – transversal 600 20 600 1.250/2.500
MARMOX Board PRO / ULTRA - 20 – longitudinal 1.250/2.500 20 600 1.250/2.500
MARMOX Board PRO / ULTRA - 30 – transversal 600 30 600 1.250/2.500
MARMOX Board PRO / ULTRA - 30 – longitudinal 1.250/2.500 30 600 1.250/2.500
Other dimensions are available upon request.
Dimensions
Standard dimensions:
MARMOX Board PRO / ULTRA - Flex
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
24
01. Measure the dimensions.
02. Adaption of the board, cutting upon request and installation of adjustable legs (ACC 013).
03. Fastening of wall bracket ACC 005 and installation of the board with glue (MS-Polymer-Glue)
fastening of perpendicular bracket ACC 006 and installation of the board with glue (MS-
Polymer-Glue).
04. Reinforcing of all joints with reinforcing fibre mesh tape, embedded into flexible cement tile
adhesive.
01 02 03
04
25
7. MARMOX Board PRO / ULTRA - Cover Panel for bath- and shower tubMARMOX Board - Cover panels are pre-cut MARMOX Board PRO or ULTRA
Tile Backer Boards, for quick installation at the job site.
MARMOX BOARD – TILE BACKER BOARDS
Usually the boards have a thickness of 30 mm, characterised by the excellent product
properties of MARMOX Board. The defined dimensions fit the most
standard applications, otherwise it is very easy the cut the element to size upon request.
The set contains the following positions:
MARMOX Board - construction boards
wall bracket / ACC 005
perpendicular bracket / ACC 006
adjustable leg / ACC 013
reinforcing fibre mesh tape
Product Qty. Thickness Length Height
mm mm mm
MARMOX Board PRO / ULTRA - 1 30 1.850 600
Bathtub Cover Panel incl. accessories 1 30 730 600
MARMOX Board PRO / ULTRA - 2 30 900 300
Showertub Cover Panel incl. accessories
Other dimensions are available upon request.
Dimensions
Standard sets:
MARMOX Board PRO / ULTRA - Cover Panel for bath- and shower tub
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
26
27
8. MARMOX Board PRO / ULTRA - Toilet Box / Front Wall InstallationMARMOX Board - Toilet Box and Front Wall Installation are pre-fabricated coverings,
made of MARMOX Board PRO or ULTRA Tile Backer Boards with 20 mm thickness.
MARMOX BOARD – TILE BACKER BOARDS
The use of MARMOX Board - Toilet Box and Front Wall Installation affect:
reduced time spent on installation
avoid or reduce any waste accured by cutting of standard boards to size
MARMOX Board - Toilet Box and Front Wall Installation are available in different stan-
dard dimensions.
Product Thickness Width Height Depth
mm mm mm mm
MARMOX Board PRO / ULTRA - Toilet-Box 425 - 1.240 20 425 1.240 240
MARMOX Board PRO / ULTRA - Toilet-Box 500 - 1.240 20 500 1.240 240
MARMOX Board PRO / ULTRA - Toilet-Box 1.000 - 1.200 20 1.000 1.200 320
MARMOX Board PRO / ULTRA - Toilet-Box 1.200 - 1.240 20 1.200 1.240 240
MARMOX Board PRO / ULTRA - Front Wall Installation 20 1.200 1.250 -
Other dimensions are available upon request.
Dimensions
Standard sets:
MARMOX Board PRO / ULTRA - Toilet Box / Front Wall Installation
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
28
29
9. MARMOX Board PRO - Insulation under electric underfloor heating systemMARMOX Board PRO is designed for application under electric underfloor heating systems.
The boards are heat insulating, compressive resistant, and ready for tiling. The boards are
available in a wide range of different thicknesses from 6 mm - 100 mm, which affect the reaction
time and the energy consumption accordingly.
MARMOX BOARD – TILE BACKER BOARDS
Electric underfloor heating is particularly popular in kitchens and bathrooms. Heating
cables are mainly embedded in self-levelling compounds or flexible tile adhesive, directly
installed on concrete floors. In cases where no insulation under the heating wires is ins-
talled, the energy loss can reach 40% of the total energy consumption for the heating of
the basement and not for the tiles.
That effect is a considerable disadvantage for the comfort and effectiveness of electric
underfloor heating systems.
The installation of MARMOX Board PRO for insulation under the electric underfloor
heating system, either on concrete, screed or wood construction provides two main
advantages:
reduced reaction time to heat up the surface temperature
reduction of energy consumption
MARMOX Board PRO is recommended by well-known producers of electric underfloor
heating systems thanks to the excellent product properties.
tiles
tiles
tile adhesive
tile adhesive
tile adhesive
heating wire
heating wire
MARMOX Board PRO
concrete floor
concrete floor
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS
30
10. AccessoriesMARMOX BOARD – TILE BACKER BOARDS
ACC001 - reinforcing fibre mesh tape 25 m x 100 mm
The tape is used to reinforce the joints between the boards and should be embedded into
flexible tiles adhesive.
packing unit = 2 rolls/bag
ACC002 - sealing tape 10 m x 125 mm
Sealing tapes are used to seal joints and feedthroughs.
packing unit = 2 rolls/bag
ACC003 - preformed sealing tape for inside-/outside
corner
Preformed sealing corners will allow easily sealing of corners.
packing unit = 2 corner/bag
ACC004 - washer
Available made of zinc coated metal or plastic for strong and save mechanical fixing with
screws or nails.
packing unit = 20 pcs./bag
ACC005 - wall bracket
Wall brackets are used for connection boards on wall or floor.
packing unit = 2 pcs./bag
31
ACC006 - perpendicular bracket
Perpendicular brackets are used to set two perpendicular boards in the right positon until
the glue dries.
packing unit = 2 pcs./bag
ACC007 - joint brackets
Joint brackets are used to connect two boards together on-line.
packing unit = 2 pcs./bag
ACC008 - water proof mortar
This waterproof cement mortar is suitable to glue sealing tape and reinforcing mesh.
packing unit = 5 kg/bag
ACC010 - 1 K - PU Adhesive Sealant Cartridge
The 1 K - PU mastic adhesive bonding and sealant will guarantee a solid, fast, and perfect
sealing for boards and accessories.
packing unit = 12 cartridges/carton
ACC012 - sealing fleece
The waterproof MARMOX sealing fleece is designed from a polyester layer and a layer
of thermoplastic elastomer. The fleece is suitable for application on walls and floors and
ready to tile. It achieves a perfect waterproof underlay. Dimensions: 2.500 x 950 mm.
packing unit = 1 pcs./unit
ACC013 - adjustable leg
The adjustable legs are recommended to adjust vertically installed boards (e.g. bath tub
covering) in their height.
packing unit = 2 pcs./bag
MARMOX BOARD PRO / ULTRA – TILE BACKER BOARDS