fold and tape here fold and tape here fold and tape here fold and tape here fold and tape here fold and tape here 1 5 1 7 1. Cut a circle through the stem end or bottom of the pumpkin for candle access. 2. Use a large spoon to scoop out the seeds and pulp from inside the pumpkin. 3. Cut out pattern along the dotted line, Crease lines and tape onto the part of the pumpkin you want to carve. 4. Trace design by poking holes with a sharp awl or needle tool then remove the pattern. 5. Cut along the dotted lines of your pattern to cut out he black areas of the pattern. 6. Push the cut-out pieces gently form the inside of the pumpkin and discard. 7. Scrape pumpkin skin in sections that are grey. Start with the outside of the design and work inward. Scrape in the same direction in each section to keep the lines uniform. 8. Place a candle or LED light inside the pumpkin to create an eerie glow! LEVEL OF DIFFICULTY MARTIN LUTHER
Transcript
fold and tape here
fold a
nd ta
pe he
re
fold
and
tape
her
efo
ld a
nd ta
pe h
ere
fold a
nd ta
pe he
re
fold and tape here
1 5 1 7
1. Cut a circle through the stem end or bottom of the pumpkin for candle access.2. Use a large spoon to scoop out the seeds and pulp from inside the pumpkin.3. Cut out pattern along the dotted line, Crease lines and tape onto the part of the pumpkin you want to carve.4. Trace design by poking holes with a sharp awl or needle tool then remove the pattern.5. Cut along the dotted lines of your pattern to cut out he black areas of the pattern.6. Push the cut-out pieces gently form the inside of the pumpkin and discard.7. Scrape pumpkin skin in sections that are grey. Start with the outside of the design and work inward. Scrape in
the same direction in each section to keep the lines uniform.8. Place a candle or LED light inside the pumpkin to create an eerie glow!
LEVEL OF DIFFICULTY
MARTIN LUTHER
fold and tape here
fold a
nd ta
pe he
re
fold
and
tape
her
efo
ld a
nd ta
pe h
ere
fold a
nd ta
pe he
re
fold and tape here
1. Cut a circle through the stem end or bottom of the pumpkin for candle access.2. Use a large spoon to scoop out the seeds and pulp from inside the pumpkin.3. Cut out pattern along the dotted line, Crease lines and tape onto the part of the pumpkin you want to carve.4. Trace design by poking holes with a sharp awl or needle tool then remove the pattern.5. Cut along the dotted lines of your pattern to cut out the black areas of the pattern.6. Push the cut-out pieces gently from the inside of the pumpkin and discard.7. Scrape pumpkin skin in sections that are grey. Start with the outside of the design and work inward. Scrape in
the same direction in each section to keep the lines uniform.8. Place a candle or LED light inside the pumpkin to create an eerie glow!
LEVEL OF DIFFICULTY
KATIE LUTHER
fold and tape here
fold a
nd ta
pe he
re
fold
and
tape
her
efo
ld a
nd ta
pe h
ere
fold a
nd ta
pe he
re
fold and tape here
1. Cut a circle through the stem end or bottom of the pumpkin for candle access.2. Use a large spoon to scoop out the seeds and pulp from inside the pumpkin.3. Cut out pattern along the dotted line, Crease lines and tape onto the part of the pumpkin you want to carve.4. Trace design by poking holes with a sharp awl or needle tool then remove the pattern.5. Cut along the dotted lines of your pattern to cut out he dark gray areas of the pattern.6. Push the cut-out pieces gently form the inside of the pumpkin and discard.7. Place a candle or LED light inside the pumpkin to create an eerie glow!
