MASTERBATCHES AND COMPOUNDS

1

SECURITY FORM:

2. Composition / information on ingredients

3. Identification of hazards

Use of the product

Product code

Product name PE Filler Master Batch

F 35

use as filler for plastic processes such as extrusion, blow molding, film, yarn, stamping, injection, tubes, plates, etc.

1. Chemical identification of the product

Composition of the material Ingredients Composition(% w/w)

CaCO3 80

LLDPE

Additive

Percentage of hazardous ingredients This product contains no hazardous ingredients

18

2

Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - info@polyfiller.eu - tel.+ 39 0382766373

Product hazard This product contains no hazardous ingredientsIt is not classified as dangerous.

health risk

environmental risk

Not risk

Not risk

MASTERBATCHES AND COMPOUNDS

2

SECURITY FORM:

4. First aid measures

5. Fire-fighting measures

6. Measures in the event of accidental spillage

7. Manipulation/Storage

Accidental exposure

Inhalation

contact with the skin

Contact with eyes

Ingestion

Rinse immediately with water, seek medical advice.

No effect after use, but wash your hands with soap and water

Solutions

Move to fresh air if discomfort persists, consult a doctor

Sciacquare la bocca. Consultare il medico

Recommended extinguishing media Avoid areas of high temperature and sparks Electric

Special precautions Do not release contaminated water into drains or surface waters

Special protective equipment Respiratory drive recommended

Procedures for the issuance or pour out Take up mechanically and collect in a suitable container. Dispose of according to local regulations.Do not release contaminated water into drains or surface waters

Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - info@polyfiller.eu - tel.+ 39 0382766373

Manipulation managed according to good industry practiceprevent the formation of dust and spillage of the product.

Storage Store in tight containers in a dry, cool and windy. Keep away from strong oxidizing agents and sources of heat.

MASTERBATCHES AND COMPOUNDS

3

SECURITY FORM:

9. Chemical and physical properties

Cleaning the workplace

Personal protection:

Eyes protection

Hand Protection

Follow the good practice of good industrial hygien

Utilize gloves approved

Wear glasses

8. Personal protection / exposure control

Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - info@polyfiller.eu - tel.+ 39 0382766373

Appearance look

Odor

Physical state

Steam pressure / temperature

Boiling Point

Melting point

Degree of liquefaction (190°C/5Kg)

Evaporation rate

Viscosity

Solubility in water

Flammability

Explosive properties

White granule

Odorless

Solid

Not evaluable

Not evaluable

105 - 115 deg.C

23g/10 mins

Not evaluable

Not evaluable

Insoluble

Fuel

Not explosive

MASTERBATCHES AND COMPOUNDS

4

SECURITY FORM:

10. Stability and reactivity

11. Toxicological information

Conditions to avoid

Material to avoid

Hazardous decomposition products

Hazardous polymerization

Avoid exposure to open flame or high temperature

Avoid contact with strong oxidizing agents

Thermal decomposition puàò release carbon dioxide, mono oxides or nitrogen oxides.

Not polymerize

Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - info@polyfiller.eu - tel.+ 39 0382766373

Effects of exposure Short-term

Oral toxicity

Acute oral toxicity

Toxicity by inhalation

Effects exposure long-term

Irritation

Sensitization

Carcinogenic characteristics

Reproductive toxicity

Teratogenic

Mutagenesis

Toxicologically synergistic product name

Data not available

Data not available

Data not available

not irritable

Data not available

Data not available

Data not available

Data not available

Data not available

Data not available

MASTERBATCHES AND COMPOUNDS

5

SECURITY FORM:

13. Ecological considerations

14. Transportation information

12. Ecological considerations

Ecological information

Eco toxicity data

The release into the environment should be avoided. The product is not soluble in water.

No data are available on the toxicity to aquatic life or other microorganisms.

Waste / unused product

Icontaminated packaging Contaminated packaging contaminated packaging should betreated as the product

Incinerate or dispose of in accordance with local regulations

transportation information

Rail transport Free unrestricted

Air transport

Maritime transport Free unrestricted

Free unrestricted

Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - info@polyfiller.eu - tel.+ 39 0382766373

MASTERBATCHES AND COMPOUNDS

6

SECURITY FORM:

15. Regulatory information

16. More Information

Regulatory information This product is suitable for food contact

reference for this document Technical details F35

Original

Date of preparation / revision

Revision number

Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - info@polyfiller.eu - tel.+ 39 0382766373