of 12
7/30/2019 material handling machine
1/12
MATERIAL HANDLINGMACHINE
State-o-the-art technologies and unsurpassed
quality achieve a signicant increase in eciency
Higher engine output, combined with Stage IIIB/Tier 4i
emission standards compliance results in considerably
lower emissions and uel consumption
Intelligent cockpit design and a user-riendly
operator inormation system
Closed swing circuit
Hose rupture valves with regeneration on the lit and stick
cylinders or uel-ecient work
Operating weight 43.5 t 48.8 t
Engine output 190 kW
Reach Up to 18 m
Technical specifcations
Unique eatures
MHL360 E
7/30/2019 material handling machine
2/1202
More power, lower uel consumption and that is
just the beginning: The new MHL360 E raises the bar
in the eld o cutting-edge scrap handling technology
with an even more sophisticated hydraulic system,
energy recovery, and a highly comortable cockpit
than previous models.
With its combination o power and reduced
emissions, as well as a hydraulic system that is both
powerul and sensitive at the same time,
the machine makes it possible to complete
even the most challenging material
handling tasks smoothly and
eciently.
SETTING NEW STANDARDSIN PERFORMANCEThe new MHL360 E
With an operating weight o 43.5 48.8 tonnes and a reach
o up to 18 m, the MHL360 E is a veritable scrap handling
powerhouse
Ideal or use at ports
A new hydraulic system design provides improved handling
capacity and eciency
Excellent stability thanks to a wide undercarriage base and
reinorced steel structure
BlueEVOLUTION technology means the MHL360 E is
ready or todays strict emission standards
7/30/2019 material handling machine
3/12
YOUR HIGH-SPECWORK STATION
The MHL360 E operator control environment sets new standards in ergonomics
and comort. Even on the toughest jobs, our exclusive new generation oair-cushioned driver seats make this a good place to work. Intuitive joystick
control, a multi-unction button and keys or direct access to individual machine
unctions all make machine operation simple. All the relevant inormation
is clearly presented to the driver on a high-resolution, high-contrast display
screen. Structural saety has also been improved by strengthening the
protective steel cab structure to meet the latest EU Machinery Directive. The
driver is assisted by a rear-view camera (tted as standard), which provides an
excellent overview o the region behind the machine.
Reducing the workload. Relieving the stress.
Comortable interior equipment drivers seat design based
on latest ergonomics research
Intuitive machine controls simple-to-operate joystick,direct access to key unctions
Everything in view job-relevant inormation clearly
displayed on the central highres, highcontrast WVGA colour
display screen, with anti-glare shield tted as standard
Simple start/stop button (operates when ignition
switched on)
Improved eld o view and an even better view to the rear
when reversing or perorming complex manoeuvres thanks
to the integral rear-view camera, tted as standard
The whole cab concept is designed to support the driver and
lighten his load, and promote a comortable and productive
environment
Ergonomically designed, well
planned interior. Aided by the colour
display and the operator console, the
driver can easily control every majorunction rom the quiet comort o
his seat in the centre o the sound-
prooed cab
Standard equipment: the rear-view
camera provides a wide-angle view
o the area behind the machine
03
7/30/2019 material handling machine
4/12
FASTER AND MORE
PRECISE THAN BEFORE
The machines sophisticatedhydraulic system is yet anotherTerex Fuchs highlight
The new hydraulic system design o the MHL360 E
provides even greater power and handling eciency
than beore. The use o separate circuit systems
means that the swiveling unit can be orceully started
and stopped without this having an impact on the
rest o the hydraulic system. In addition, it makes it
possible to perorm simultaneous swiveling and liting
maneuvers at high speeds with utmost precision even when handling large loads. The energy
recovery system in the hydraulic system is also an
innovation worth mentioning: When the superstructure
retards, the braking energy is ed back into the main
pump. Moreover, standard hose rupture valves with
regeneration helps ensure that the system requires
lower pump delivery rates, saving additional energy
in the process. These eatures not only reduce the
load on the engine, but also increase the machines
handling capacity up to 20% compared to the D-series
while maintaining the same levels o uel consumption.
The new MHL360 E eatures a highly ecient cooling system:
Advanced fow design, sel-regulating an drive, and thermally
insulated cooling systems provide outstanding cooling
perormance even under adverse conditions. Maintenance is
easier by design: Special access steps, large standing platorms
improve accessibility to all components, and a clearly-arranged
electrical system all help reduce service complexity04
7/30/2019 material handling machine
5/12
PERFORMANCE UP,
EMISSIONS DOWNBlueEVOLUTION: The future generation stronger, quieter and cleaner than everEvolution means a continuous development o thegood to the even better. Terex has employed this
philosophy on our Terex Fuchs material handlers
rom the beginning, making us the innovation leader
in this market. The driving orce o these eorts is
our aim to provide the most modern technologies
and the best quality to you, our customer.
BlueEVOLUTION represents our latest step orward,
an all-embracing intelligent set o energy-related
measures harmonizing, perormance, resourcesaving, and operating costs.
Eciency and innovation are at the heart o
BlueEVOLUTION. The new MHL360 E has been
equipped with a more powerul turbo-diesel engine,
which not only boasts an impressive increase
in output, but also uses signicantly less uel
protecting the environment and reducing your costs
at the same time. The engines high-perormance
cooling unit keeps the engine at the ideal
temperature level, and thus increases its eciency.
The engine works in harmony with our load sensinghydraulic system, which provides the power you
need on demand, but doesnt waste uel generating
excess hydraulic fow. The complete package oers
a uture-oriented solution or perormance-oriented
material handling businesses with a strong sense o
responsibility who are already thinking o tomorrow
today.
Burner Fuel supply
Diesel
particle lter
air
pump
A powerul new heart beats
quietly inside the
Terex Fuchs MHL360 E:
a 6-cylinder engine at the
cutting edge o technology
a great platorm or
ecient energy use. Through
BlueEVOLUTION, were not
just helping your business,
but also this blue planet weall live on
The Terex Fuchs MHL360 E machine with BlueEVOLUTION
technology meets strict TIER4i/II IB emission limits
Despite systematically reducing emission levels, engine power
has been increased to 190 kW
Low uel consumption puts the brakes on operating costs
caused by todays high oil prices
Intelligent engine management and a high-perormance cooling
system protects against overloading and deliver real benets in
eciency
05
7/30/2019 material handling machine
6/1206
TECHNICAL DATAOPERATING WEIGHTWITHOUT ATTACHMENTS
MHL360 Series E 43.5 t - 48.8 t
Manuacturer and model Deut z 7.8 L6 4V
Design 6-cylinder inline
Engine control EMR IV
Type 4-stroke diesel, common rail direct injection, turbocharger,
controlled exhaust gas recirculation, diesel particulate flter with
automatic regeneration
Engine output 190 kW
Nominal speed 2000 min-1
Displacement 7.8 l
Cooling system Combi-cool er (coolant/charge air) with an speed control
system; optional reversing unction
Emission standard Stage I II B / EPA Tier 4 interim
Air f lter des ign Two-stage flter with saety cartr idge and pre-separator with
discharge valve
Usable tank capacity 653 l
DIESEL ENGINE
ELECTRICAL SYSTEMGenerator 28 V / 100 A
Operating voltage 24 V
Battery 2 x 12 V / 110 Ah / 750 A (in accordance with EN)
Lighting set 2 x H3 headlamps, turn indicators and tail lights
Option20 kW or 30 kW DC generator with controls and insulationmonitoring, driven by V-belt direct rom diesel engine
TRAVEL DRIVEHydrostatic travel drive via infnitely variable axial piston motor
with directly mounted travel brake valve, two-speed manual
gearshit, 4-wheel drive
Maximum speed, 1st gear max. 5 km/h
Maximum speed, 2nd gear max. 15 km/h
Gradeability max. 30 %
Turning radius 8.0 m
SWING DRIVESwing gear Internally toothed double-row ball ring gear
Drive 3-stage planetary gear with integrated multi-disc brake
Upper carriage swing speed 0 - 6 min-1 infnitely variable
Swing brake Electrically operated
Max. pivot torque 91 kNm
UNDERCARRIAGEFront axle Planetary drive axle with integrated drum brake, rigidly mounted,
max. steering angle 27
Rear axle Oscillating planetary drive rear axle with integrated drum brake
and selectable oscillating axle lock
Stabilizers 4-point stabilizersTires Solid rubber, 8-ply 12.00 - 24
BRAKE SYSTEMService brake Hydraulic single-cir cuit braking system acti ng on al l our wheel
pairs
Parking brake Electrically operated disc brake on transmi ssion, acting on both
ront and rear axles
REXROTH mobile hydraulic system with load limit control and
uel-saving power demand control; closed swing circuit; hose
rupture valves with regeneration on the lit and stick cylindersor uel-efcient work
Hydraulic oil flter Integral return flter in oil tank or work hydraulics, with 3000
operating hrs service interval; oil fltration on closed swing
circuit
Max. Pump capaci ty 2 x 280 l/min & 1 x 140 l/min (or swing operat ion)
Max. Operating pressure 320/360 bar
Hydraulic oil tank 520 l usable tank capacity
HYDRAULIC SYSTEM
Liting gear Elasti cal ly suppor ted, infni tely variable hydraul ically elevat able
with max. eye level o 6.10m; independent orward movement
o up to 2.20 m; Sound-deadened; heat-insulated windows or
optimum view; Sound-insulated; heat-insulating glass windows
or optimum view feld; windshield with pull-down sunblind that
slides under the cab roo; viewing window on cab roo; sliding
window in cab door; height and tilt-adjustable steering column
Heating Infnitely variable heating with 3-speed an, 6 adjustable
deroster nozzles (hot water system)
Operator s seat A ir-cush ioned comort-seat wi th in tegra ted headrest, sa ety bel t
and lumbar support, seat heating with integrated A/C unction
optional. Comortable operation with multi-purpose adjustment
options or seat position, seat inclination, and seat cushion
placement in relation to armrests and pilot control units
Monitoring Ergonomic layout; anti-glare instrumentation. Multiunctiondisplay, automatic monitoring and recording o abnormal
operating conditions (including all hydraulic oil flters, hydraulic
oil temperature (cold/hot) - coolant temperature and charge
air temperature - condition o cooling system, diesel particulate
flter load), visual and audible warning indication with shutdown
o pilot controls/engine power reduction. Diagnosis o individual
sensors possible via the multi-unction display. Rear view camera
Air conditioning Automatic
Acoustic power level LW(A)
= 104 dB(A) (guaranteed) in accordance
with directive 2000/14 EC
OPERATOR CAB
OFFICIAL HOMOLOGATIONCertifed in accordance with CE regulations
7/30/2019 material handling machine
7/1207
STANDARD OPTION
Exhaust gas turbocharger Charge air cooling Direct electronic uel injection/common rail Automatic idle Engine preheating Engine diagnostics interace System-controlled an drive with an speed monitoring
MHL360 EEQUIPMENTENGINE STANDARD OPTION
All-wheel drive with dierential Drum brakes Rear axle oscillating lock 2-speed powershit transmission 4-point stabilizers Stabilizer cylinders with integrated two-way check valves Piston rod protection on stabilizer cylinders Stabilizer plates 510 x 665 4-point stabilizers, individually controllable Dozer blade with plastic or Hardox edge (in addition to 4-point stabilizers) Tool box Special paint (customer paint work)
UNDERCARRIAGE
STANDARD OPTION
Separate cooling systems (combi-cooler or engine and hydraulic oil
cooler)
Cooling system an speeds controlled by operating parameters Fan drive reversing unction Lockable maintenance hatches, with gas struts Automatic central lubrication system Rear view camera Reversing alarm Electric reuelling pump Lighting protection Special paint (customer paint work)
UPPER CARRIAGE
STANDARD OPTION
Cab system horizontally and vertically adjustable Saety glass Hinged windscreen Sliding window in cab door Glazed roo panel
Hinged roo opening Reinorced glass (windscreen and roo panel) Windscreen washer system Windshield washer system (lower portion o windshield) Air-cushioned operator seat with headrest, seatbelt, and lumbar support Seat heating with integrated A/C unction Steering column, height and tilt adjustable Automatic air conditioning system Independent heating system Multi-unction display Document clip
Protective grilles to ront and roo 12V transormer Radio CD player 12V power outlet Fire extinguisher, dry powder Rotating beacon
CAB
STANDARD OPTION
20 kW DC generator with controls and insulation monitoring 30 kW DC generator with controls and insulation monitoring Close proximity range limiter or dipperstick Coolant and hydraulic oil level monitoring system Filter system or attachments Hose rupture protection or lit cylinder Hose rupture protection or dipperstick cylinder Overload warning device Quick coupling on dipperstick Cut-o ball valve on dipperstick Dipperstick impact protection Cyclonic pre-separator or air-flter Hydraulic oil preheating Float switch Joystick steering Lubrication o the grab suspension by central lubrication system H3 headlamps H3 worklights on boom and dipperstick (up to 4) Xenon worklights on boom and dipperstick (up to 4) Front-mounted Xenon worklights (up to 2) Xenon worklights on cab roo (up to 4)
EQUIPMENT
Further optional equipment on request
7/30/2019 material handling machine
8/12
MHL360 E 195 3315
540
3200
5980
1935 3000
1595
2900
3555
290
615
1700
2940
3000
4520
5030
A
B C
D
E
2010
195
1900
08
DIMENSIONS
TRANSPORT DIMENSIONS MHL360 E
Dimensions Reach 16.5 m Reach 18.0 m Reach 18.0 m cranked
A 13,830 mm 14,615 mm 14,610 mm
B 6,375 mm 6,400 mm 5,915 mm
C 1,715 mm 1,715 mm 1,715 mm
D 3,555 mm/3,750 mm* 3,555 mm/3,750 mm* 3,555 mm/3,750 mm*
E 3,400 mm 3,700 mm 3,750 mm
* with a protective mesh or the cab roo
LOADING SYSTEM WITH DIPPERSTICK MHL360 E
Components 16.5 m 18.0 m 18.0 m cranked
Straight boom 8.9 m Straight boom 9.7 m Cranked boom 9.7 m Dipperstick 7.0 m Dipperstick 7.8 m
Loading system 18 m cranked: Undercarriage equipped with dozer blade, rotated by 180
1900Avg. center of gravi tyin transport position
7/30/2019 material handling machine
9/1209
WORKING RANGES/LIFTING CAPACITIESREACH 18 M WITH DIPPERSTICK
The lit capacity values are stated in metric tons (t). The pump pressure is 360 bar. In accordance with
ISO 10567 the lit capacity values represents 75% o the static tipping loads or 87% o the hydraulic
liting orce (marked ). On solid and l evel ground the values apply to a swing range o 360. The (...)
values apply in the longitudinal direction o the undercarriage. The values or not supported only applyvia the steering axle or the locked oscillating axle. The weights o the attached load hoisting equipment
(grab, load hook, etc.) must be deducted rom the lit capacity values. The working load o the liting
devise must be observed. In accordance with the EN 474-5 or object handling application hose rupture
valves on the boom and stick cylinders, an overload warning device and the lit capacity table in the cab
are required. For object handling application the machine has to be supported on a level ground.
Loading system Boom 9.7 m,
Dipperstick 7.8 m,
Cactus grab 0,8 m3 open
RECOMMENDED ATTACHMENTSTerex Fuchs cactus grab 0.6 m3 Open or hal-closed shells
Terex Fuchs cactus grab 0.8 m3 Open or hal-closed shells
Terex Fuchs MAGNETIC PLATE MP 1350 dia. = 1350 mm with magnet system 30 kW
Clamshell grab 1.4 m3 Loose goods density up to 1,600 kg/m3
Clamshell grab 2.0 m3 Loose goods density up to 800 kg/m3
Lit hooks 20 t
MHL360 E20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 3Reach in m
Height
m
Undercarriage
stabilisation 6 7.5
9 10.5 12 13.5 15 16.5 18
15Without stabilizers (8.8) (6.8) (5.3)
With 4-pt stabilizers 8.8 (8.8) 7.9 (7.9) 6.3 (6.3)
13.5Without stabilizers (7.0) (5.5) (4.3)
With 4-pt stabilizers 7.7 (7.7) 7.0 (7.0) 5.9 (5.9)
12Without stabilizers (7.0) (5.5) (4.4) (3.5)
With 4-pt stabilizers 7.7 (7.7) 6.9 (6.9) 6.3 (6.3) 5.1 (5.1)
10.5Without stabilizers (6.9) (5.4) (4.4) (3.5)
With 4-pt stabilizers 7.7 (7.7) 6.9 (6.9) 6.3 (6.3) 5.4 (5.7)
9Without stabilizers (8.8) (6.7) (5.3) (4.3) (3.5) (2.8)
With 4-pt stabilizers 9.0 (9.0) 7.9 (7.9) 7.0 (7.0) 6.3 (6.3) 5.4 (5.7) 4.5 (5.1)
7.5Without stabilizers (8.4) (6.5) (5.2) (4.2) (3.4) (2.8)
With 4-pt stabilizers 9.3 (9.3) 8.1 (8.1) 7.2 (7.2) 6.4 (6.4) 5.3 (5.7) 4.5 (5.1)
6Without stabilizers (10.7) (8.0) (6.2) (4.9) (4.0) (3.3) (2.7)
With 4-pt stabilizers 11.8 (11.8) 9.8 (9.8) 8.4 (8.4) 7.3 (7.3) 6.2 (6.5) 5.2 (5.7) 4.4 (5.1)
4.5Without stabilizers (13.7) (9.8) (7.4) (5.8) (4.7) (3.9) (3.2) (2.7) (2.2)
With 4-pt stabilizers 16.5 (16.5) 12.6 (12.6) 10.3 (10.3) 8.6 (8.6) 7.3 (7.4) 6.0 (6.5) 5.2 (5.7) 4.4 (5.0) 3.7 (4.2)
3Without stabilizers (12.0) (8.8) (6.8) (5.4) (4.4) (3.7) (3.1) (2.6) (2.2)
With 4-pt stabilizers 17.8 (17.8) 13.3 (13.3) 10.6 (10.6) 8.6 (8.8) 7.0 (7.5) 5.9 (6.5) 5.0 (5.7) 4.3 (4.9) 3.7 (4.0)
1 .5Without stabilizers (9.1) (8.0) (6.3) (5.1) (4.2) (3.5) (3.0) (2.5) (2.2)
With 4-pt stabilizers 9.1 (9.1) 13.2 (13.5) 10.2 (10.7) 8.2 (8.8) 6.7 (7.5) 5.7 (6.4) 4.8 (5.5) 4.2 (4.7) 3.7 (3.7)
0Without stabilizers (6.9) (7.4) (5.9) (4.8) (4.0) (3.5) (2.9) (2.5) (2.1)
With 4-pt stabilizers 6.9 (6.9) 12.6 (13.1) 9.7 (10.5) 7.9 (8.7) 6.5 (7.3) 5.5 (6.2) 4.7 (5.3) 4.1 (4.4) 3.3 (3.3)
- 1 .5Without stabilizers (6.9) (7.1) (5.6) (4.6) (3.8) (3.2) (2.8) (2.4)
With 4-pt stabilizers 6.9 (6.9) 12.1 (12.1) 9.4 (9.9) 7.6 (8.2) 6.4 (6.9) 5.4 (5.8) 4.7 (4.9) 3.9 (3.9)
- 3Without stabilizers (7.5) (6.9) (5.4) (4.4) (3.7) (3.2) (2.7) (2.4)
With 4-pt stabilizers 7.5 (7.5) 10.7 (10.7) 8.9 (8.9) 7.5 (7.5) 6.2 (6.2) 5.3 (5.3) 4.3 (4.3) 3.2 (3.2)
- 4 .5Without stabilizers (6.9) (5.4) (4.4) (3.7) (3.1) (2.7)
With 4-pt stabilizers 8.8 (8.8) 7.6 (7.6) 6.4 (6.4) 5.4 (5.4) 4.4 (4.4) 3.4 (3.4)
- 6Without stabilizers (4.4) (3.7)
With 4-pt stabilizers 5.0 (5.0) 4.1 (4.1)
Reach m
2,7Without stabilizers (2.1)
With 4-pt stabilizers 3.6 (3.8)
max. reach 18.2 m
7/30/2019 material handling machine
10/1210
WORKING RANGES/LIFTING CAPACITIESREACH 16.5 M WITH DIPPERSTICK
Loading system Boom 8.9 m,
Dipperstick 7.0 m,
Cactus grab 0,8 m3 open
RECOMMENDED ATTACHMENTSTerex Fuchs cactus grab 0.6 m3 Open or hal-closed shells
Terex Fuchs cactus grab 0.8 m3 Open or hal-closed shells
Terex Fuchs cactus grab 1.0 m3 Open or hal-closed shells
Terex Fuchs MAGNETIC PLATE MP 1350 dia. = 1350 mm with magnet system 30 kW
Clamshell grab 1.4 m3 Loose goods density up to 1,600 kg/m3
Clamshell grab 2.0 m3 Loose goods density up to 800 kg/m3
Lit hooks 20 t
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 3Reach in m
The lit capacity values are stated in metric tons (t). The pump pressure is 360 bar. In accordance with
ISO 10567 the lit capacity values represents 75% o the static tipping loads or 87% o the hydraulic
liting orce (marked ). On solid and level ground the values apply to a swing range o 360. The (...)
values apply in the longitudinal direction o the undercarriage. The values or not supported only apply
via the steering axle or the locked oscillating axle. The weights o the attached load hoisting equipment
(grab, load hook, etc.) must be deducted rom the lit capacity values. The working load o the liting
devise must be observed. In accordance with the EN 474-5 or object handling application hose rupture
valves on the boom and stick cylinders, an overload warning device and the lit capacity table in the cab
are required. For object handling application the machine has to be supported on a level ground.
Height
m
Undercarriage
stabilisation 6 7.5
9 10.5 12 13.5 15 16.5
15Without stabilizers (8.4) (5.8)
With 4-pt stabilizers 8.4 (8.4) 5.8 (5.8)
13.5Without stabilizers (8.7) (6.7) (5.2)
With 4-pt stabilizers 9.3 (9.3) 8.3 (8.3) 5.8 (5.8)
12Without stabilizers (8.8) (6.8) (5.3) (4.2)
With 4-pt stabilizers 9.2 (9.2) 8.2 (8.2) 7.5 (7.5) 5.0 (5.0)
10.5Without stabilizers (8.8) (6.8) (5.3) (4.3)
With 4-pt stabilizers 9.2 (9.2) 8.2 (8.2) 7.4 (7.4) 6.5 (6.7)
9Without stabilizers (8.6) (6.7) (5.3) (4.3) (3.4)
With 4-pt stabilizers 9.4 (9.4) 8.3 (8.3) 7.5 (7.5) 6.4 (6.7) 5.3 (5.6)
7.5Without stabilizers (11.2) (8.4) (6.5) (5.2) (4.2) (3.4)
With 4-pt stabilizers 11.2 (11.2) 9.7 (9.7) 8.5 (8.5) 7.6 (7.6) 6.4 (6.8) 5.3 (6.0)
6Without stabilizers (14.8) (10.6) (8.0) (6.2) (5.0) (4.1) (3.4)
With 4-pt stabilizers 14.8 (14.8) 12.2 (12.2) 10.2 (10.2) 8.8 (8.8) 7.6 (7.7) 6.3 (6.8) 5.2 (6.0)
4.5Without stabilizers (13.8) (9.9) (7.5) (5.9) (4.8) (3.9) (3.3) (2.7)
With 4-pt stabilizers 17.0 (17.0) 13.1 (13.1) 10.7 (10.7) 9.0 (9.0) 7.4 (7.8) 6.1 (6.8) 5.2 (6.0) 4.4 (4.8)
3Without stabilizers (12.3) (9.0) (7.0) (5.6) (4.6) (3.8) (3.2) (2.7)
With 4-pt stabilizers 18.4 (18.4) 13.8 (13.8) 10.9 (10.9) 8.7 (9.2) 7.1 (7.9) 6.0 (6.8) 5.1 (5.8) 4.4 (4.8)
1 .5Without stabilizers (11.1) (8.3) (6.5) (5.3) (4.4) (3.7) (3.1) (2.7)
With 4-pt stabilizers 12.2 (12.2) 13.6 (14.0) 10.4 (11.2) 8.4 (9.2) 6.9 (7.8) 5.8 (6.7) 5.0 (5.6) 4.3 (4.4)
0Without stabilizers (9.1) (7.8) (6.2) (5.0) (4.2) (3.5) (3.0) (2.7)
With 4-pt stabilizers 9.1 (9.1) 13.0 (13.6) 10.0 (10.9) 8.1 (9.0) 6.7 (7.5) 5.7 (6.4) 4.9 (5.2) 3.8 (3.8)
- 1 .5Without stabilizers (8.9) (7.5) (6.0) (4.9) (4.1) (3.5) (3.0)
With 4-pt stabilizers 8.9 (8.9) 12.6 (12.6) 9.8 (10.2) 7.9 (8.5) 6.6 (7.0) 5.6 (5.8) 4.6 (4.6)
- 3Without stabilizers (9.6) (7.4) (5.8) (4.8) (4.0) (3.4) (3.0)
With 4-pt stabilizers 9.6 (9.6) 10.9 (10.9) 9.1 (9.1) 7.5 (7.5) 6.2 (6.2) 5.0 (5.0) 3.6 (3.6)
- 4 .5Without stabilizers (7.5) (5.8) (4.8) (4.0)
With 4-pt stabilizers 8.7 (8.7) 7.4 (7.4) 6.2 (6.2) 5.0 (5.0)
Reach m
2.7Without stabilizers (2 .6 )
With 4-pt stabilizers 4 .0 (4 . 0)
max. reach 16.7 m
7/30/2019 material handling machine
11/1211
MHL360 E
REACH 18 M CRANKEDLoading system Cranked Boom 9.7 m,
Dipperstick 7.8 m,
Cactus grab 0,8 m3 open
RECOMMENDED ATTACHMENTSTerex Fuchs cactus grab 0.6 m3 Open or hal-closed shells
Terex Fuchs cactus grab 0.8 m3 Open or hal-closed shells
Terex Fuchs MAGNETIC PLATE MP 1250 dia. = 1250 mm with magnet system 30 kW
Clamshell grab 1.4 m3 Loose goods density up to 1,600 kg/m3
Clamshell grab 2.0 m3 Loose goods density up to 800 kg/m3
Lit hooks 20 t
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 3Reach in m
The lit capacity values are stated in metric tons (t). The pump pressure is 360 bar. In accordance with
ISO 10567 the lit capacity values represents 75% o the static tipping loads or 87% o the hydraulic
liting orce (marked ). On solid and l evel ground the values apply to a swing range o 360. The (...)
values apply in the longitudinal direction o the undercarriage. The values or not supported only apply
via the steering axle or the locked oscillating axle. The weights o the attached load hoisting equipment
(grab, load hook, etc.) must be deducted rom the lit capacity values. The working load o the liting
devise must be observed. In accordance with the EN 474-5 or object handling application hose rupture
valves on the boom and stick cylinders, an overload warning device and the lit capacity table in the cab
are required. For object handling application the machine has to be supported on a level ground.
Height
m
Undercarriage
stabilisation 6 7.5
9 10.5 12 13.5 15 16.5 18
15Without stabilizers (6.5) (5.3)
With 4-pt stabilizers 6.5 (6.5) 5.5 (5.5)
13.5Without stabilizers (5.4) (4.2)
With 4-pt stabilizers 5.9 (5.9) 5.2 (5.2)
12Without stabilizers (5.5) (4.3) (3.4)
With 4-pt stabilizers 5.8 (5.8) 5.4 (5.4) 4.4 (4.4)
10.5Without stabilizers (5.4) (4.3) (3.4)
With 4-pt stabilizers 5.9 (5.9) 5.4 (5.4) 5.0 (5.0)
9Without stabilizers (6.6) (5.3) (4.2) (3.4) (2.7)
With 4-pt stabilizers 6.6 (6.6) 6.0 (6.0) 5.5 (5.5) 5.1 (5.1) 4.4 (4.4)
7.5Without stabilizers (6.5) (5.1) (4.1) (3.3) (2.7)
With 4-pt stabilizers 6.8 (6.8) 6.1 (6.1) 5.6 (5.6) 5.1 (5.1) 4.4 (4.7)
6Without stabilizers (7.9) (6.1) (4.9) (3.9) (3.2) (2.7)
With 4-pt stabilizers 8.3 (8.3) 7.2 (7.2) 6.4 (6.4) 5.7 (5.7) 5.1 (5.1) 4.3 (4.7)
4.5Without stabilizers (13.7) (9.7) (7.3) (5.7) (4.6) (3.8) (3.1) (2.6) (2.1)
With 4-pt stabilizers 14.0 (14.0) 10.8 (10.8) 8.9 (8.9) 7.6 (7.6) 6.6 (6.6) 5.9 (5.9) 5.0 (5.2) 4.3 (4.7) 3.6 (3.6)
3Without stabilizers (11.8) (8.7) (6.7) (5.3) (4.3) (3.6) (3.0) (2.5) (2.1)
With 4-pt stabilizers 15.7 (15.7) 11.7 (11.7) 9.4 (9.4) 7.9 (7.9) 6.8 (6.8) 5.8 (6.0) 4.9 (5.3) 4.2 (4.7) 3.6 (4.0)
1 .5Without stabilizers (10.4) (7.8) (6.1) (4.9) (4.1) (3.4) (2.8) (2.4) (2.1)
With 4-pt stabilizers 10.6 (10.6) 12.4 (12.4) 9.8 (9.8) 8.0 (8.0) 6.6 (6.9) 5.6 (6.0) 4.7 (5.3) 4.1 (4.7) 3.6 (4.0)
0Without stabilizers (7.8) (7.2) (5.7) (4.6) (3.8) (3.2) (2.7) (2.3)
With 4-pt stabilizers 7.8 (7.8) 12.3 (12.6) 9.6 (10.0) 7.7 (8.2) 6.4 (7.0) 5.4 (6.0) 4.6 (5.2) 4.0 (4.5)
- 1 .5Without stabilizers (7.6) (6.8) (5.4) (4.4) (3.7) (3.1) (2.7) (2.3)
With 4-pt stabilizers 7.6 (7.6) 11.9 (12.3) 9.2 (9.9) 7.5 (8.1) 6.2 (6.9) 5.3 (5.9) 4.5 (5.1) 4.0 (4.3)
- 3Without stabilizers (7.9) (6.6) (5.2) (4.2) (3.6) (3.0) (2.6) (2.3)
With 4-pt stabilizers 7.9 (7.9) 11.6 (11.6) 9.0 (9.4) 7.3 (7.8) 6.1 (6.6) 5.2 (5.6) 4.5 (4.7) 3.9 (3.9)
- 4 .5Without stabilizers (8.6) (6.6) (5.1) (4.2) (3.5) (3.0) (2.6)
With 4-pt stabilizers 8.6 (8.6) 10.4 (10.4) 8.6 (8.6) 7.2 (7.2) 6.0 (6.0) 5.1 (5.1) 4.2 (4.2)
- 6Without stabilizers (9.3) (6.7) (5.2) (4.2) (3.5) (3.0) (2.7)
With 4-pt stabilizers 9.3 (9.3) 8.9 (8.9) 7.5 (7.5) 6.3 (6.3) 5.3 (5.3) 4.4 (4.4) 3.3 (3.3)
Reach m
2,7Without stabilizers (2.0)
With 4-pt stabilizers 3.5 (5.5)
max. reach 18.1 m
7/30/2019 material handling machine
12/12
www.terex-uchs.com
Product range/Standard machines
Powerul perormance with low uel consumption
levels, extreme loading capacities, high speeds:
These characteristics make the Terex
FuchsMHL360 E mobile material handling machine stand
out among the competition and show how the units
new generation has been ne-tuned even urther
in order to perectly meet our customers needs.
The ully reengineered hydraulic system design
in particular provides previously inconceivable
perormance levels in terms o eciency and speed,
perorming day ater day o demanding work. And
it goes without saying that operators will be able
to control this powerhouse with utmost saety and
precision rom the units high-comort cab, which
has numerous eatures designed to provide a
comortable and ergonomic working environment.
MHL360 E
Valid rom: Juli 2012. Product specifcations and prices are subject to change without notice or obligation. The photographs and/or drawings containedin this document are or illustrative purposes only. Please reer to the appropriate Operators Manual or instructions on the proper use o this equipment.Failure to ollow the appropriate Operators Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. Theonly warranty applicable to our equipment is the standard written warranty applicable to the particular product. Terex makes no other warranty, expressed orimplied. Products and services listed may be trademarks, service marks or trading names o Terex Corporation and/or its subsidiaries in the USA and other
countries. All rights reserved. Terex is a registered trademark o Terex Corporation in the United States o America and in many other countries. 2012Terex Corporation.
A history of great ideas since 1888
Ever since the business was ounded in 1888, the
Fuchs name has signied a wealth o ideas and
innovation. Whether developing the legendary
Fuchs 301 cable excavator in 1957 or patenting theelevatable cab in 1975, pioneering technical advances
have shaped the brands history right up to the
present day, and helped Terex Fuchs machines to
win their reputation or top quality workmanship and
endurance. Terex Fuchs ocuses its resources on
clearly dened areas o application, oering high-
perormance materials handlers to the recycling,
scrap handling, port and timber industries. This
concentration on core sectors delivers important user
benets: instead o standard o-the-shel products,
we provide tailored, highly customisable machine
solutions, which can be adapted to the precise needs
o our customers.
MHL320 MHL331 MHL335 MHL340 MHL340 FQC MHL350 MHL350 FQC MHL360 MHL380
85 kW 114 kW 114 kW 128 kW 128 kW 160 kW 160 kW 190 kW 273 kW
8.2-10.4 m 10.7-12.0 m 10.7-12.0 m 12.2-13.7 m 11.0-11.2 m 14.0-16.0 m 12.5-13.0 m 16.5-18.0 m 18.5-21.0 m
17.8-19.0 t 22.0-23.5 t 23.5-25.0 t 27.5-29.0 t 28.5-31.3 t 32.0-35.5 t 32.0-37.5 t 43.5-48.8 t 66.0-67.0 t
0.4-0.6 m3 0.4-0.6 m3 0.4-0.8 m3 0.4-0.8 m3Attachmentson request
0.6-0.8 m3Attachmentson request
0.6-1.0 m3 1.0-1.4 m3
MHL454 MHL474
176 kW 213 kW
9.8-10.85 m 11.15 m
31.0-32.5 t 41.5-44.0 t
1.7-2.5 m2 2.0-4.0 m2