+ All Categories
Home > Documents > MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... ·...

MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... ·...

Date post: 29-May-2020
Category:
Upload: others
View: 143 times
Download: 17 times
Share this document with a friend
33
MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION Product Name: Calcigel - Calcium Hydroixde Paste with Barium Sulphate INTENDED USE: Pulp Capping on vital pulp. Company Name: Prevest Denpro Limited Address: 38, Industrial Estate, Digiana, Jammu-180010 (India) Tel: + 91-191-2430442 Fax No. +91-191-2430442 Email: [email protected] Web: www.prevestdenpro.com Emergency Contact No:- +91-191-2432548 SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS Chemical Name CAS EINECS Classification Content Calcium Hydroxide 001305-62-0 215-137-3 C; R36/38 35 Barium Sulfate 007727-43-7 231-784-4 C; R36/38 2 SECTION 3: HAZARDS IDENTIFICATION HAZARD DESIGNATION “C” – Corrosive R36/38: Irritating to eyes and skin. EMERGENCY OVERVIEW PHYSICAL APPEARANCE: White Paste IMMEDIATE CONCERNS: R36/38:Irritating to eyes and skin. POTENTIAL HEALTH EFFECTS EYES: Causes eye burns SKIN: Causes skin burns INGESTION: Harmfull if swallowed INHALATION: Irritating to the nose, throat and respiratory tract. SECTION 4: FIRST AID MEASURES Eyes : Immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. Have eyes examined and tested by medical personnel. Skin : Immediately flush skin with plenty of water. Remove clothing. Get medical
Transcript
Page 1: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 1 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Calcigel - Calcium Hydroixde Paste with Barium Sulphate

INTENDED USE: Pulp Capping on vital pulp.

Company Name: Prevest Denpro Limited Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442

Email: [email protected]

Web: www.prevestdenpro.com Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name CAS EINECS Classification Content

Calcium Hydroxide 001305-62-0 215-137-3 C; R36/38 35

Barium Sulfate 007727-43-7 231-784-4 C; R36/38 2

SECTION 3: HAZARDS IDENTIFICATION

HAZARD DESIGNATION

“C” – Corrosive

R36/38: Irritating to eyes and skin.

EMERGENCY OVERVIEW

PHYSICAL APPEARANCE: White Paste

IMMEDIATE CONCERNS: R36/38:Irritating to eyes and skin.

POTENTIAL HEALTH EFFECTS

EYES: Causes eye burns

SKIN: Causes skin burns

INGESTION: Harmfull if swallowed

INHALATION: Irritating to the nose, throat and respiratory tract.

SECTION 4: FIRST AID MEASURES

Eyes : Immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. Have eyes examined and

tested by medical personnel.

Skin : Immediately flush skin with plenty of water. Remove clothing. Get medical

Page 2: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 2 OF 33

attention immediately. Wash clothing separately before reuse.

Ingestion : if swallowed, do not induce vomiting. Give victim a glass of water or milk. Call a physician or poison control center immediately. Never give anything by mouth to

an unconscious person.

Inhalation : Remove to fresh air, if not breathing , give artificial respiration or give oxygen by

trained personnel. Seek immediate medical attention.

SECTION 5: FIRE-FIGHTING MEASURES

Fire Fighting Procedures : General: Evacuate all personnel; use protective equipment for fire-fighting . use self –contained breathing apparatus when the

product is involved in fire.

Fire-Fighting Equipment : Non combustible

SECTION 6: ACCIDENTAL RELEASE MEASURES

Small Spill : Clean up spills immediately, observing precautions in Protective

Equipment section. Large Spill : Collect in tightly closed containers

Environmental Precautions

Water Spill : Do not allow to enter sewers or drains that many lead to waterways.

SECTION 7: HANDLING AND STORAGE

Handling : Use suitable protective equipment

Storage : Room Temperature

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Personal Protective Equipment

Eyes And Face : Wear safety glasses with side shields(or goggles) and a face shield.

Skin: S36/37 : Wear suitable protective clothing and gloves

Respiratory : S51 : Use only in well-ventilated areas.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Physical State : Paste

Odor : Odorless or no characteristic odor Colour : White

SECTION 10: STABILITY AND REACTIVITY

Stability : Stable when stored and handled under recommended conditions.

Conditions To Avoid : Acidic conditions

Incompatible Meterials : Strong acids, metals

Page 3: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 3 OF 33

SECTION 11: TOXICOLOGICAL INFORMATION

N/A

SECTION 12: ECOLOGICAL INFORMATION

Environmental Data : Biodegradability-Non established

Ecotoxicological Information : Not yet determined

SECTION 13: DISPOSAL CONSIDERATIONS

Disposal Method : Dispose of in compliance with governmental requlation (EC-1975l0442-20/11

SECTION 14: TRANSPORT INFORMATION

Road And Rail(ADR/RID)

Proper Shipping Name : Corrosive liquid, basic inorganic, N.O.S.( Calcium hydroxide mixture)

Packing Group : III

Air(ICAO/IATA) Shipping Name : Corrosive liquid, basic inorganic, N.O.S.( Calcium hydroxide mixture)

Packing Group : III

Vessel(IMO/IMDG)

Proper Shipping Name : Corrosive liquid, basic inorganic, N.O.S.( Calcium hydroxide mixture)

Packing Group : III Limited Quantity : I L

SECTION 15: REGULATORY INFORMATION

European Community

EEC Label Symbol And Classification

“C” – Corrosive

R 36/38: Irritating to eyes and skin.

SECTION 16: OTHER INFORMATION

FOR DENTAL USE ONLY: Use as directed. The information and recommended are taken from sources(

raw material MSDS(s) and manufacture’ s knowledge) believed to be accurate; however, Oratech

Products, LLC , makes no warrenty with respect to the accuracy of the information or the suitability of

the recommendation and assumes no liability to any use thereof. Each user should review these recommendation in the specific context of the intended use and determine whether they are

appropriate.

Page 4: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 4 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Calplus - Calcium Hydroxide Paste with Iodoform

INTENDED USE: Direct & indirect pulp capping, apexification, temporary & permanent filling of infected root canal

Company Name: Prevest Denpro Limited

Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442

Email: [email protected] Web: www.prevestdenpro.com

Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

Full text of risk phrases appearing in section 3: see section 16.

Hazardous substances present on their own:

(present in the preparation at a sufficient concentration to give it the toxicological characteristics it

would have in a 100% pure state) Hazardous Ingredients CAS# PEL TLV %

Iodoform 75-47-8 N/A N/A 30-40

Other Ingredients

Calcium hydroxide, Silicon oil

Other substances representing a hazard: No known substance in this category present.

Substances present at a concentration below the minimum danger threshold:

No known substance in this category present.

Other substances with occupational exposure limits:

No known substance in this category present.

SECTION 3: HAZARDS IDENTIFICATION

This product is not classed as flammable. Refer to the recommendations regarding the other products present on the site

Possibility of serious lesions to the eyes.

Preparation classification:

Irritant

R 41 Risk of serious damage to eyes.

Other data: Packaging < 125 ml.

Page 5: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 5 OF 33

SECTION 4: FIRST AID MEASURES

As a general rule, in case of doubt or if symptoms persist, always call a doctor.

NEVER induce swallowing in an unconscious person.

In the event of splashes or contact with eyes: Wash thoroughly with soft, clean water for 15 minutes holding the eyelids open.

If there is any redness, pain or visual impairment, consult an ophthalmologist.

SECTION 5: FIRE-FIGHTING MEASURES

Not relevant.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal precautions : Consult the safety measures listed under headings 7 and 8.

Environmental precautions : Prevent any material from entering drains or waterways.

Use drums to dispose of waste recovered in accordance with applicable regulations (see heading 13).

If the product contaminates waterways, rivers or drains, alert the

relevant authorities in accordance with statutory procedures

Methods for cleaning up : Clean preferably with a detergent, do not use solvents.

SECTION 7: HANDLING AND STORAGE

The regulations relating to storage premises apply to workshops where the product is handled.

Fire prevention : Prevent access by unauthorised personnel. Recommended equipment and procedures : For personal safety, see §8.

Observe precautions stated on label and also industrial safety regulations

Product must not come into contact with the eyes

Prohibited equipment and procedures : Smoking, eating and drinking are prohibited in

premises where the preparation is used Never open the packages under pressure

Storage : Keep the container tightly closed in a dry place.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Use personal protection equipment as per Directive 89/686/EEC.

Exposure limit values per INRS ED 984:

France VME-ppm: VME-mg/m3: VLE-ppm: VLE-mg/m3: Notes: TMP N°:

1305-62-0 - 5 - - - Exposure limit values (2003-2006):

UK/WELs TWA: STEL: Ceiling: Definition: Criterion:

1305-62-0 5 mg/m3 - - - -

UK/OES TWA: STEL: Ceiling: Definition: Criterion:

1305-62-0 5 mg/m3 - - - -

ACGIH/TLV TWA: STEL: Ceiling: Definition: Criterion: 1305-62-0 5 mg/m3 - - - -

Page 6: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 6 OF 33

Eye and face protection:

Avoid contact with eyes. Wear safety goggles.

Provide eye washes in workshops where the product is constantly handled

Skin protection:

For further information, see § 11 of S.D.S. - Toxicological information.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

General information:

Physical state: paste

Important health, safety and environmental information:

pH of the substance or preparation: not relevant.

The pH is impossible to measure or its value is not relevant. Boiling point/boiling range: not specified.

Flash point interval: not relevant.

Vapour pressure: not relevant.

Density: not stated.

Water solubility: Dilutable.

Other information: melting point/melting range: not specified.

Self-ignition temperature: not specified.

Decomposition point/decomposition range : not specified.

SECTION 10: STABILITY AND REACTIVITY

The preparation is stable at the handling and storage conditions recommended per § 7 of the safety

data sheet,

SECTION 11: TOXICOLOGICAL INFORMATION

No data is available regarding the preparation itself.

It is generally agreed that substances contained are likely to cause, when applied to the eye of an

animal, serious eye damage which persists

for at least twenty-four hours.

SECTION 12: ECOLOGICAL INFORMATION

No ecological data on the product itself is available.

The product must not be allowed to run into drains or waterways.

SECTION 13: DISPOSAL CONSIDERATIONS

Do not pour into drains or waterways.

Waste : Recycle or dispose of waste in compliance with current legislation,

preferably via a certified collector or company.

Do not contaminate the ground or water with waste, do not dispose of waste into the environment.

Soiled packaging : Empty container completely. Keep label(s) on container.

Page 7: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 7 OF 33

Give to a certified disposal contractor.

SECTION 14: TRANSPORT INFORMATION

Exempt from transport classification and labelling. Transport product in compliance with provisions of the ADR for road, RID for rail, IMDG for sea and

ICAO/IATA for air transport (ADR 2009 - IMDG 2008 - ICAO/IATA 2009).

SECTION 15 : REGULATORY INFORMATION

This preparation was classified in compliance with the directive known as <All preparations>

1999/45/EC and its adaptations. In addition directive 2008/58/EC with the 30° adaptation of

directive 67/548/EEC (Hazardous substances) have been taken into account.

In addition directive 2009/2/EC with the 31° adaptation of directive 67/548/EEC (Hazardous

substances) have been taken into account. In addition Regulation (EC) No 1272/2008 have been taken into account.

This product is not classed as flammable.

Packaging < 125 ml.

Preparation classification:

Contains:

215-137-3 CALCIUM HYDROXIDE

Particular hazards associated with the preparation and safety recommendations:

R 41 Risk of serious damage to eyes. S 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

S 36/39 Wear suitable protective clothing and eye/face protection.

S 45 In case of accident or if you feel unwell, seek medical advice immediately (show the label

where possible).

S 60 This material and its container must be disposed of as hazardous waste.

SECTION 16: OTHER INFORMATION

Since the user's working conditions are not known by us, the information supplied on this safety data

sheet is based on our current level of knowledge and on national and community regulations.

The product must not be used for any purposes other than those specified under heading 1 without

first obtaining written handling instructions. It is at all times the responsibility of the user to take all necessary measures to comply with legal

requirements and local regulations.

The information given on this safety data sheet must be regarded as a description of the safety

requirements relating to our product and not a guarantee of its properties

Full text of risk phrases appearing in section 3: R 38 Irritating to skin.

R 41 Risk of serious damage to eyes.

Page 8: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 8 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Dolo EDTA Gel - EDTA Gel Carbamode Peroxide in water soluble base INTENDED USE: EDTA Lubricant

Company Name: Prevest Denpro Limited

Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442 Email: [email protected]

Web: www.prevestdenpro.com

Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

· Chemical characterization

· Description : Mixture of substances listed below with nonhazardous additions.

·

Dangerous components:

CAS: 124-43-6 EINECS: 204-701-4

hydrogen peroxide--urea

C, O; R 8-34

2.5-10%

· Additional information For the wording of the listed risk phrases refer to section 16.

SECTION 3: HAZARDS IDENTIFICATION

· Hazard description : not applicable · Information concerning to particular hazards to man and environment

The product does not have to be labelled due to the calculation procedure of the "General

Classification

guideline for preparations of the EU" in the latest valid version.

· Classification system

The classification is according to the latest editions of the EU-lists, and extended by company and literature data.

SECTION 4: FIRST AID MEASURES

· General information No special measures required.

· After inhalationSupply fresh air; consult doctor in case of complaints.

· After skin contactImmediately wash with water and soap and rinse thoroughly.

· After eye contactRinse opened eye for several minutes under running water.

Page 9: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 9 OF 33

· After swallowingInduce vomiting, if person is conscious. Seek medical help.

SECTION 5: FIRE-FIGHTING MEASURES

· Suitable extinguishing agents CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.

· Protective equipment: Wear self-contained respiratory protective device

SECTION 6: ACCIDENTAL RELEASE MEASURES

Person-related safety precautions : Not required.

Measures for environmental protection : Do not allow product to reach sewage system or

any water course.

Measures for cleaning/collecting : Pick up mechanically. Additional information : No dangerous substances are released.

SECTION 7: HANDLING AND STORAGE

HandlingProduct is intended for dental use only.

Information for safe handling : No special measures required. Observe normal care for

working with chemicals.

Information about fire - and explosion protection: No special measures required.

Storage Requirements to be met by storerooms and receptacles: Store only in the original receptacle.

Information about storage in one common storage facility : Not required.

Further information about storage conditions : Protect from heat and direct sunlight.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

· Additional information about design of technical facilities: No further data; see item 7.

· Ingredients with limit values that require monitoring at the workplace:

57-55-6 propane-1,2-diol

OES

Long-term value: 474* 10** mg/m³, 150* ppm

total (vapour and particulates) **particulates

Additional information: The lists valid during the making were used as basis.

Personal protective equipment

General protective and hygienic measures The usual precautionary measures are to be adhered to when handling chemicals. Keep away from

foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash hands

before breaks and at the end of work.

Respiratory protection: Not required.

Page 10: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 10 OF 33

Protection of hands:

The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the

product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of

the penetration times, rates of diffusion and thedegradation

Material of gloves

The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several

substances, the resistance of the glove material can not be calculated in advance and has therefore to

be checked prior to the application.

Penetration time of glove material

The exact break trough time has to be found out by the manufacturer of the protective gloves and has

to be observed.

Eye protection : Safety glasses

Body protection : Protective work clothing.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

General Information

Form: paste

Colour: Whitish

Odour: Weak, characteristic

Change in condition

Melting point/Melting range: undetermined

Boiling point/Boiling range: undetermined

Ignition temperature: 400°C

Flash point: Not applicable

Self-igniting: Product is not selfigniting.

Danger of explosion: Product does not present an explosion hazard.

Density: Not determined

Solubility in / Miscibility with Water: Soluble

SECTION 10: STABILITY AND REACTIVITY

Thermal decomposition / conditions to be avoided : No decomposition if used according

to specifications. Dangerous reactions No : Dangerous reactions known

Dangerous decomposition products : No dangerous decomposition

products known

SECTION 11: TOXICOLOGICAL INFORMATION

Acute toxicity : Nil

Primary irritant effect : Nil

on the skin : May cause skin irritation

Page 11: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 11 OF 33

on the eye : Irritating effect.

Sensitization : No sensitizing effects known. Additional toxicological information:

The product is not subject to classification according to the calculation method of the General EU

Classification Guidelines for Preparations as issued in the latest version.

When used and handled according to specifications, the product does not have any harmful effects to

our experience and the information provided to us.

SECTION 12: ECOLOGICAL INFORMATION

General notes : Water hazard class 1 (German Regulation) (Self-assessment):

slightly

hazardous for water.

SECTION 13: DISPOSAL CONSIDERATIONS

Product

· Recommendation

Must not be disposed together with household garbage. Do not allow product to reach

sewage system.

· Uncleaned packaging:

· Recommendation: Disposal must be made according to official regulations.

SECTION 14: TRANSPORT INFORMATION

Land transport ADR/RID (cross-border)

ADR/RID class: - Not Known

Maritime transport IMDG:

IMDG Class: -

Marine pollutant: No

Air transport ICAO-TI and IATA-DGR:

ICAO/IATA Class:- Non Dangerous

SECTION 15: REGULATORY CONSIDERATIONS

Labelling according to EU guidelines : Observe the general safety regulations when handling chemicals. The product is not subject to

identification regulations under EU Directives and

the Ordinance on Hazardous Materials (German

GefStoffV).

National regulations Technical instructions (air):

Page 12: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 12 OF 33

Class

Share in %

III 9.0

SECTION 16: OTHER INFORMATION

This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.

Relevant R-phrases

34 Causes burns.

8 Contact with combustible material may cause fire.

Page 13: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 13 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Pulp X- Pulp Devitalizer

INTENDED USE: Dental

Company Name: Prevest Denpro Limited

Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442

Email: [email protected] Web: www.prevestdenpro.com

Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

Hazardous substances present:

INDEX CAS EC Name Symb. R: %

10808033 137-58-6 2053028 LIGNOCAINE Xn 22 30 - 60 10808305 0525-89-4 POLYOXY

METHYLENE Xn 36/37/38 43

40.C3 20/22 10 - < 30

10808026 8022-77-3 244-350-4 CAMPHOR

(RACEMIC) Xn 11 36/37/38 22 10 - < 30

604-008-00-0 106-48-9 203-402-6 PARACHLORO- PHENOL Xn, N 20/21/22 51/53 < 10

SECTION 3: HAZARDS IDENTIFICATION

Hazard Classification: NON-DANGEROUS GOODS

Harmful (Xn) Dangerous for the Environment (N) Risk Phrases:

R 20/22 - Harmful by inhalation and if swallowed.

R 36/37/38 - Irritating to eyes, respiratory system and skin.

R 43 - May cause sensitisation by skin contact.

R 40 - Limited evidence of a carcinogenic effect.

R 52/53 - Harmful to aquatic organisms; may cause long-term adverse effects in the aquatic environment.

Safety Phrases :

S 36/37 Wear suitable protective clothing and gloves.

S 26 In case of contact with eyes, rinse immediately with plenty of

water and seek medical advice.

Page 14: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 14 OF 33

S 9 Keep container in a well-ventilated place.

S 60 This material and its container must be disposed of as hazardous waste.

SECTION 4: FIRST AID MEASURES

For advice, contact a Poisons Information Centre (Australia: 13 1126, New Zealand: 0800 764 766) or

a doctor (at once). If swallowed, do NOT induce vomiting. Avoid giving milk or oils. Urgent hospital treatment is likely to

be needed at once.

As a general rule, in case of doubt or if symptoms persist, always call a doctor. NEVER induce

swallowing in an unconscious person.

In the event of exposure by inhalation:

In the event of inhalation, move the patient into the fresh air and keep him/her warm and still. If breathing is irregular or has stopped, effect mouth-to-mouth resuscitation and call a doctor. Do not

give the patient anything orally. If the person is unconscious, place in the recovery position and call an

ambulance.

In the event of splashes or contact with eyes:

If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes.

In the event of skin or hair contact:

If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running

water.

SECTION 5: FIRE-FIGHTING MEASURES

Not relevant.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal precautions : Avoid any contact with the skin and eyes. Avoid

inhaling dust. Consult the safety measures listed under headings 7 and 8. If a large quantity has been spilt,

evacuate all personnel and only allow intervention by trained

operators equipped with safety apparatus.

Environmental precautions : Prevent any material from entering drains or

waterways. Use drums to dispose of waste recovered in accordance with applicable regulations (see heading 13). If the

product contaminates waterways, rivers or drains, alert the

relevant authorities in accordance with statutory procedures

Methods for cleaning up : Clean preferably with a detergent, do not use

solvents

SECTION 7: HANDLING AND STORAGE

The regulations relating to storage premises apply to workshops where the product is handled. Anyone with a history of skin sensitisation must on no account handle such products

Handling : Handle in well-ventilated areas.

Page 15: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 15 OF 33

Fire prevention : Prevent access by unauthorised personnel.

Recommended equipment and

procedures : For personal safety, see §8. Observe precautions stated on

label and also industrial safety regulations Avoid inhaling vapors. Carry

out any industrial operation which may give rise to this in a sealed

apparatus. In all cases, recover emissions at source Provide vapor extraction at the emission

source and also general ventilation of the

premises Also provide breathing apparatus for certain

short tasks of an exceptional nature and for emergency

interventions Avoid contact of product with the skin and eyes.

Prohibited equipment and procedures : Smoking, eating and drinking are prohibited in premises

where the preparation is used Never open the packages

under pressure

Storage : Keep the container tightly closed in a dry place. Keep away

from food and drink, including those for animals.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Use personal protection equipment. Anyone with a history of skin sensitisation must on no account

handle such products.

Technical measures : Ensure adequate ventilation, if possible with

extractor fans at work posts and appropriate

general extraction. Check the atmosphere periodically. If this

ventilation is insufficient to maintain the concentration of vapors below the exposure limits, wear breathing apparatus

Respiratory protection : With this preparation, avoid in particular any

inhalation of vapors.

Hand protection : Protective creams may be used for exposed skin,

but they should not be applied after contact with

the product. In the event of prolonged or repeated contact with the hands, use appropriate gloves.

Eye and face protection : Avoid contact with eyes. Wear safety goggles.

Provide eye washes in workshops where the product is constantly

handled.

Skin protection : For further information, see § 11 of S.D.S. – Toxicological information.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

General information : Physical state: paste

Important health, safety

and environmental information : pH of the substance or preparation: not

relevant.

The pH is impossible to measure or its value is not relevant.

Boiling point/boiling range : not specified.

Page 16: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 16 OF 33

Flash point interval : not relevant.

Vapour pressure : not relevant. Density : not stated.

Water solubility : Insoluble.

Other information : Melting point/melting range: not specified.

Self-ignition temperature: not specified.

Decomposition point/ decomposition range : not specified.

SECTION 10: STABILITY AND REACTIVITY

The preparation is stable at the handling and storage conditions recommended per § 7 of the safety

data sheet.

SECTION 11: TOXICOLOGICAL INFORMATION

No data is available regarding the preparation itself.

It is generally agreed that substances contained are likely to cause tissue damage in less than four

hours after application to the healthy, unbroken skin of an animal.

It is generally agreed that substances contained are likely to cause serious irritation of the respiratory

system It is generally agreed that substances contained are likely to cause, among certain predisposed subjects, a sensitisation reaction by cutaneous route. It is generally agreed that substances contained are

likely to cause category 3 mutagenic effects

SECTION 12: ECOLOGICAL INFORMATION

No ecological data on the product itself is available. The product must not be allowed to run into

drains or waterways.

Ecotoxicity : Harmful to aquatic organisms, may cause long-term adverse

effects in the aquatic environment.

SECTION 13: DISPOSAL CONSIDERATIONS

Do not pour into drains or waterways.

Waste : Recycle or dispose of waste in compliance with current

legislation, preferably via a certified collector or company. Do not

contaminate the ground or water with waste, do not dispose of waste into

the environment. Soiled packaging : Empty container completely. Keep label(s) on container.

Give to a certified disposal contractor.

SECTION 14: TRANSPORT INFORMATION

Exempt from transport classification and labelling. Transport product in compliance with provisions of

the ADR for road, RID for rail, IMDG for sea and ICAO/IATA for air transport (ADR 2007 - IMDG 2006

- ICAO/IATA 2007).

SECTION 15: REGULATORY INFORMATION

Page 17: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 17 OF 33

Hazard classification according to Approved Criteria for Classifying Hazardous Substances [NOHSC:1008(2004)] 3rd Edition and the Australian Code for the Transport of Dangerous Goods by

Road and Rail (6th Edition) M.S.D.S prepared in accordance with the National Code of Practice for the

Preparation of Material Safety Data Sheets, 2nd Edition [NOHSC:2011(2003)]

SECTION 16: OTHER INFORMATION

Since the user's working conditions are not known by us, the information supplied on this safety data sheet is based on our current level of knowledge and on national and community regulations. The

product must not be used for any purposes other than those specified under heading 1 without first

obtaining written handling instructions. It is at all times the responsibility of the user to take all

necessary measures to comply with legal requirements and local regulations. The information given on

this safety data sheet must be regarded as a description of the safety requirements relating to our product and not a guarantee of its properties

Full text of risk phrases appearing in section 3:

R 20/21/22 Harmful by inhalation, in contact with skin and if swallowed.

R 20/22 Harmful by inhalation and if swallowed.

R 22 Harmful if swallowed.

R 36/37/38 Irritating to eyes, respiratory system and skin. R 43 May cause sensitisation by skin contact.

R 51/53 Toxic to aquatic organisms, may cause long-term adverse effects

in the aquatic environment

Page 18: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 18 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Orafil LC - Light Cured Temporary Filling Material

INTENDED USE: - Temporary fillings, temporary protection in inlay and onlay technique

Company Name: Prevest Denpro Limited

Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442

Email: [email protected] Web: www.prevestdenpro.com

Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

Chemical characterization: Mixtures

Description: Mixture of the substances listed below with nonhazardous additions.

Dangerous components:

868-77-9 2-hydroxyethyl methacrylate 5-10%

Skin Irrit. 2, H315; Eye Irrit. 2, H319; Skin Sens. 1, H317; STOT SE 3, H335

SECTION 3: HAZARDS IDENTIFICATION

Health effects are based on the unmixed/uncured material.

Under FDA regulations this product is classified as a medical device. Medical devices are exempt from the labelling provisions of GHS according to the Hazard

Communication Standard (HCS).

Classification of the substance or mixture

Skin Sens. 1H317May cause an allergic skin reaction.

Label elements

Hazard pictograms GHS07 Signal word Warning

Hazard statements

May cause an allergic skin reaction.

Precautionary statements

Wear protective gloves / protective clothing. If skin irritation or rash occurs: Get medical advice/attention.

Dispose of contents/container in accordance with local/regional/national/international regulations.

Other hazards Use only for intended scope of application

Page 19: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 19 OF 33

Results of PBT and vPvB assessment

PBT: Not applicable. vPvB: Not applicable.

SECTION 4: FIRST AID MEASURES

Description of first aid measures

After inhalation : Seek medical treatment in case of complaints.

After skin contact : Immediately wash with water and soap and rinse thoroughly.

After eye contact : Rinse opened eye for several minutes under running water. Then consult a doctor.

After swallowing : If symptoms persist consult doctor.

Information for doctor:

Most important symptoms and effects, both acute and delayed : No further relevant information

available.

Indication of any immediate medical attention and special treatment needed : No further

relevant information available.

SECTION 5: FIRE-FIGHTING MEASURES

Extinguishing media

Suitable extinguishing agents:

CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant

foam.

Special hazards arising from the substance or mixture :No further relevant information available.

Advice for firefighters Protective equipment : No special measures required.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures : Not required.

Environmental precautions : No special measures required.

Methods and material for containment and cleaning up : Pick up mechanically.

SECTION 7: HANDLING AND STORAGE

Handling:

Precautions for safe handling : For dental use only.

Information about protection against explosions and fires : No special measures required.

Conditions for safe storage, including any incompatibilities Storage:

Requirements to be met by storerooms and receptacles : See storage instructions on

package Information about storage in one common storage facility : Not required.

Further information about storage conditions : None.

Page 20: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 20 OF 33

Specific end use(s) No further relevant information available.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Additional information about design of technical systems : No further data; see item 7. Control parameters

Components with limit values that require monitoring at the workplace :

The product does not contain any relevant quantities of materials with critical values that have to be

monitored at the workplace.

Additional information : The lists that were valid during the creation were used as basis. Exposure controls

Personal protective equipment:

General protective and hygienic measures : The usual precautionary measures for

handling chemicals should be followed. ·

Breathing equipment : Not required.

Protection of hands: Protective gloves

Material of gloves The selection of the suitable gloves does not only depend on the material, but also

on further marks of quality and varies from manufacturer to manufacturer. As the product is a

preparation of several substances, the resistance of the glove material can not be calculated in

advance and has therefore to be checked prior to the application. Eye protection : Not required

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties

General Information

Appearance:

Form : Pasty

Color : Whitish Odor : Characteristic

pH-value : Not determined.

Change in condition

Melting point/Melting range : Undetermined

Boiling point/Boiling range : Undetermined

Flash point : Not applicable. Auto igniting : Product is not selfigniting.

Danger of explosion : Product does not present an explosion hazard.

Density : Not determined.

Solubility in / Miscibility with Water : Not miscible or difficult to mix.

Viscosity: Dynamic : Not determined

Kinematic : Not determined.

Other information : No further relevant information available.

SECTION 10: STABILITY AND REACTIVITY

Reactivity : No further relevant information available.

Chemical stability

Page 21: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 21 OF 33

Thermal decomposition / conditions

to be avoided : No decomposition if used according to specifications. Possibility of hazardous reactions : No dangerous reactions known.

Conditions to avoid : No further relevant information available.

Incompatible materials : No further relevant information available.

Hazardous decomposition products : No dangerous decomposition products known.

SECTION 11: TOXICOLOGICAL INFORMATION

Information on toxicological effects

Acute toxicity:

Primary irritant effect:

on the skin : No irritant effect on the eye : No irritating effect

Sensitization : Sensitization possible through skin contact.

Additional toxicological information:

The product shows the following dangers according to internally approved calculation methods for

preparations

SECTION 12: ECOLOGICAL INFORMATION

Toxicity

Aquatic toxicity : No further relevant information available.

Persistence and degradability : No further relevant information available.

Behavior in environmental systems

Bioaccumulative potential : No further relevant information available.

Mobility in soil : No further relevant information available. Additional ecological information:

General notes : Water hazard class 1 (Self-assessment): slightly hazardous for

water

Results of PBT and vPvB assessment

PBT : Not applicable. vPvB : Not applicable.

Other adverse effects : No further relevant information available.

SECTION 13: DISPOSAL CONSIDERATIONS

Waste treatment methods

Recommendation : Smaller quantities can be disposed of with household waste. Uncleaned packagings

Recommendation : Disposal must be made according to official regulations

SECTION 14: TRANSPORT INFORMATION

UN-Number

DOT, ADR, ADN, IMDG, IATA : Void

Page 22: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 22 OF 33

UN proper shipping name DOT, ADR, ADN, IMDG, IATA : Void

Transport hazard class(es)

DOT, ADR, ADN, IMDG, IATA Class : Void

Packing group

DOT, ADR, IMDG, IATA : Void

Environmental hazards:

Marine pollutant : No Special precautions for user : Not applicable.

Transport in bulk according to

Annex II of MARPOL73/78 and

the IBC Code : Not applicable

UN "Model Regulation" : Void

SECTION 15: REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or mixture

Sara

Section 355 (extremely hazardous substances) : None of the ingredients are listed. Section 313 (Specific toxic chemical listings) : None of the ingredients are listed.

TSCA (Toxic Substances Control Act):

One or more substances contained in this material are not listed on the TSCA Inventory. Contact

VOCO for more information.

Proposition 65 Chemicals known to cause cancer:

None of the ingredients are listed.

Chemicals known to cause reproductive toxicity for females:

None of the ingredients are listed

Chemicals known to cause reproductive toxicity for males:

None of the ingredients are listed Chemicals known to cause developmental toxicity:

None of the ingredients are listed

Cancerogenity categories

EPA (Environmental Protection Agency)

None of the ingredients are listed TLV (Threshold Limit Value established by ACGIH)

Contact VOCO for more information.

NIOSH-Ca (National Institute for Occupational Safety and Health)

None of the ingredients are listed

GHS label elements

The product is classified and labeled according to the Globally Harmonized System (GHS). Hazard pictograms GHS07

Signal word Warning

Page 23: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 23 OF 33

Hazard statements

May cause an allergic skin reaction. Precautionary statements

Wear protective gloves / protective clothing.

If skin irritation or rash occurs : Get medical advice/attention.

Dispose of contents/container in accordance with local/regional/national/international regulations.

SECTION 16: OTHER INFORMATION

The information contained herein is based on our present knowledge and is believed to be correct at

the date issued. The information is subject to change without notice. However, all information, statements, recommendations or suggestions shall not constitute any guarantee, representation or

warranty, expressed or implied. Final determination whether the product is fit and suitable for a

particular purpose and the user's method of use or application is the sole responsibility of the user.

Page 24: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 24 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Chlor X - Chlorhexidine Gluconate Solution

INTENDED USE: Dental Company Name: Prevest Denpro Limited

Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442

Email: [email protected] Web: www.prevestdenpro.com

Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

Name CAS no Einecs-no Content (%) Classification

Chlorhexidine

digluconate

18472-51-0 242-354-0 2 -

SECTION 3: HAZARDS IDENTIFICATION

Classification: Not harmful.

Classification according

to EU Regulation 1272/2008: The composition is not classified as hazardous.

Label information: The product does not need to be labelled in accordance with

EU directives.

SECTION 4: FIRST AID MEASURES

Inhalation: Fresh air Skin contact: Rinse immediately with plenty of water. If the symptoms remain, seek medical

advice.

Eye contact: Keep the eyelids open and rinse immediately with plenty of water. Call hospital

and continue with the treatment to the ophthalmologist is reached.

Ingestion: Rinse with water. Drink water in small sips.

Further information: Never give any food and/or drink to an unconscious person. Please show this safety data sheet to the doctor on duty. Get medical attention

in case of uncertainty.

Page 25: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 25 OF 33

SECTION 5: FIRE-FIGHTING MEASURES The product is not combustible:

Suitable extinguishing media: Use carbon dioxide, foam, powder or water spray. Containers close to fire should be removed or cooled with water.

Extinguishing media which

must not be used: Use extinguishing media based on other products and chemicals

stored in the vicinity of this product.

Specific risks related to the product itself, combustion products or resulting gases:

known. Hazardous Decomposition Products: Carbon dioxide.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal precautions: Avoid contact with eyes and skin.

Environmental precautions: Do not discharge into drains, contain with sand, kiselgur or

other suitable medium and collect.

SECTION 7: HANDLING AND STORAGE Handling: The product must be handled carefully in accordance with a

healthy practice in the workplace. Avoid inflicting damage on the

packing.

Storage: Store cold, not >25 ºC. Protect from light.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure limit values: -

Exposure controls: All work should be carried out in accordance with strict hygiene practices. All work should take place in suitable premises, in

accordance with the existing legislation and regulations. Avoid

substance contact. See also heading 7. Handling and storage.

Limitation of exposure in the workplace:

· respiratory protection: Not required if treated properly.

· hand protection: In case of direct contact with the substance use gloves of rubber or PVC.

· eye protection: In case of direct contact with the substance, eye protection

should be used. Make eye wash possible.

· skin protection: In case of direct contact with the substance use protective

clothing. Environmental exposures: Avoid release to the environment.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

General information:

Page 26: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 26 OF 33

· Appearance: Colourless to pale yellow liquid.

· Odour: Odourless. Important health, safety and environmental information:

· pH: 5,5 - 7 · Boiling point/interval: 100⁰C

· Flash point : -- · Flammability (solid, gas): --

· Explosive properties: -- · Oxidizing properties: --

· Vapour pressure: -- · Density, kg/m³: 1060 – 1070 · Solubility in water: Mixable. · Solubility in organic

solvents: and ethanol acetone

· Vapour density: -- · Evaporation rate: --

· Partition coefficient:

noctanol/water: -- · Viscosity: --

SECTION 10: STABILITY AND REACTIVITY

Conditions to avoid: Stable under normal conditions.

When heated to decomposition produces toxic fumes of chlorine and nitrogen oxides.

SECTION 11: TOXICOLOGICAL INFORMATION

Human health effects and symptoms: · inhalation: Under normal use, no danger

· ingestion: May be irritating to the lining of the esophagus and the

stomach. For concentrated chlorhexidinedigluconat :LD50oral

rat, 2000 mg/kg.

· Skin contact: Under normal use, no danger. May cause skin irritation in

sensitive individuals after repeated and/or prolonged contact · eye contact: Eye contact may cause transient mild stinging

· Further information: Carcinogenicity and teratogenicity: No indications.

SECTION 12: ECOLOGICAL INFORMATION

Toxicity: No data available.

Biodegradation: Biodegradable

Bioaccumulation: No bioaccumulation potential

SECTION 13: DISPOSAL CONSIDERATIONS

Product: Disposed of in compliance with local and national regulations. Contaminated packaging: Should be dispose of as normal waste, incineration.

SECTION 14: TRANSPORT INFORMATION

The product is not dangerous goods. No special transport conditions are required.

ADR/RID Not dangerous goods

ICAO/IATA

Page 27: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 27 OF 33

Not dangerous goods

IMO/IMDG Not dangerous goods

SECTION 15: REGULATORY INFORMATION

Health, safety and environmental information shown on the label: The product is not labelled. It must be used according to manufacturer’s recommendations and

managed by medically qualified person.

Precautions:

P102; Keep out of reach of children + P405; Store locked up.

P305; IF IN EYES + P351; Rinse cautiously with water for several minutes + P314; Get medical Advice /attention if you feel unwell.

Further information:

Safety Data Sheet according to REACH 1907/2006/EC. Classification

and Labelling (CLP) EU Regulation 1272/2008. This product meets the demands of MDD

93/42/EEC. The product is CE marked.

SECTION 16: OTHER INFORMATION

References: Not Available

Other Special Considerations: Not Available

Created: 27.04.2013

The information contained herein is based on data considered accurate. However , No warranty is

expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. In no event will the manufacture of the distributor be responsible for damages of any nature

whatsoever resulting from the use of or reliance upon this information. General properties

are to be regarded as guidelines and are not guaranteed for all samples

Page 28: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 28 OF 33

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

Product Name: Zical - Root Canal Sealer

INTENDED USE: Antibacterial ZOE Root Canal Sealant

Company Name: Prevest Denpro Limited

Address: 38, Industrial Estate, Digiana, Jammu-180010 (India)

Tel: + 91-191-2430442

Fax No. +91-191-2430442

Email: [email protected] Web: www.prevestdenpro.com

Emergency Contact No:- +91-191-2432548

SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

Full text of risk phrases appearing in section 3: see section 16. Hazardous substances present on their own: (present in the preparation at a sufficient concentration to give it the toxicological characteristics it would have in a 100% pure state)

INDEX CAS EC Name Symb R: %

10808019 1314-13-2 ZINC OXIDE N 50/53 50 <= x % < 100

10808048 552-22-7 IODOFORM C 34 25 <= x % < 50

Other substances representing a hazard:

No known substance in this category present.

Substances present at a concentration below the minimum danger threshold:

No known substance in this category present.

Other substances with occupational exposure limits: No known substance in this category present.

SECTION 3: HAZARDS IDENTIFICATION

This product is not classed as flammable. Refer to the recommendations regarding the other products

present on the site Possibility of corrosive effects. Very toxic to aquatic organisms, may cause long-

term adverse effects in the aquatic environment.

Other data : Packaging < 125 ml.

SECTION 4: FIRST AID MEASURES

As a general rule, in case of doubt or if symptoms persist, always call a doctor. NEVER induce swallowing in an unconscious person.

Page 29: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 29 OF 33

In the event of splashes or contact with eyes:

Wash thoroughly with soft, clean water for 15 minutes holding the eyelids open. If there is any redness, pain or visual impairment, consult an ophthalmologist.

In the event of splashes or contact with skin:

Remove all contaminated or stained clothing immediately. Do not use them again until they have been

decontamined.

Wash the skin thoroughly with soap and water or a recognised cleaner. DO NOT use solvents or thinners.

If the contaminated area is widespread and/or there is damage to the skin, a doctor must be consulted

or the patient transferred to hospital

In the event of swallowing:

If swallowed accidentally, do not allow to drink, do not induce vomiting and transfer to hospital

immediately by ambulance. Show the label to the doctor.

SECTION 5: FIRE-FIGHTING MEASURES

Not relevant.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Personal precautions : Avoid any contact with the skin and eyes.

Consult the safety measures listed under headings 7 and 8.

Environmental precautions: Prevent any material from entering drains or waterways.

Use drums to dispose of waste recovered in accordance with

applicable regulations (see heading 13). If the product contaminates waterways, rivers or drains, alert the relevant

authorities in accordance with statutory procedures

Methods for cleaning up : Clean preferably with a detergent, do not use solvents.

SECTION 7: HANDLING AND STORAGE

The regulations relating to storage premises apply to workshops where the product is handled.

Fire prevention : Prevent access by unauthorised personnel.

Recommended equipment and procedures : For personal safety, see §8. Observe precautions stated on label and also industrial safety regulations

Product must not come into contact with the skin and eyes

Provide safety showers and eye washes in workshops where the product is handled constantly

Prohibited equipment and procedures:

Smoking, eating and drinking are prohibited in premises where the preparation is used. Never open the packages under pressure

Storage : Keep the container tightly closed in a dry place.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Use personal protection equipment as per Directive 89/686/EEC.

Exposure limit values per INRS ED 984:

France VME-ppm: VME-mg/m3: VLE-ppm: VLE-mg/m3: Notes: TMP N°:

Page 30: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 30 OF 33

1314-13-2 - 5 - - - -

Exposure limit values (2003-2006):

UK/OES TWA: STEL: Ceiling: Definition: Criterion:

1314-13-2 5 mg/m3 10 mg/m3 - - -

ACGIH/TLV TWA: STEL: Ceiling: Definition: Criterion:

1314-13-2 2 mg/m3 10 mg/m3 - - R

Hand protection : Protective creams may be used for exposed skin, but they should

not be applied after contact with the product. Where there is a

risk of contact with the hands, suitable gloves must be used

Eye and face protection : Avoid contact with the skin and eyes

Provide personnel with gloves, face masks and safety goggles. Provide eye washes in workshops where the product is constantly

handled

Skin protection : Wear suitable protective clothing, in particular an apron and

boots. These items must be kept in good condition and cleaned

after use. For further information, see § 11 of S.D.S. - Toxicological information.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

General information:

Physical state : powder or dust

Important health, safety and environmental information:

pH of the substance

or preparation : not relevant. The pH is impossible to measure or its value is not

relevant.

Boiling point/boiling range: not specified.

Flash point interval : not relevant.

Vapour pressure : not relevant.

Density : not stated Water solubility : Insoluble.

Other information:

melting point/melting range: not specified.

Self-ignition temperature : not specified.

Decomposition point/ decomposition range : not specified.

SECTION 10: STABILITY AND REACTIVITY

The preparation is stable at the handling and storage conditions recommended per § 7 of the safety

data sheet,

SECTION 11: TOXICOLOGICAL INFORMATION

Page 31: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 31 OF 33

No data is available regarding the preparation itself. It is generally agreed that substances contained

are likely to cause tissue damage in less than four hours after application to the healthy, unbroken skin of an animal.

SECTION 12: ECOLOGICAL INFORMATION

No ecological data on the product itself is available.

The product must not be allowed to run into drains or waterways.

Ecotoxicity:

Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. In accordance with Directive 2006/8/EC:

CAS EC

1314-13-2

ZINC OXIDE

SECTION 13: DISPOSAL CONSIDERATIONS

Do not pour into drains or waterways.

Waste : Recycle or dispose of waste in compliance with current legislation,

preferably via a certified collector or company.

Do not contaminate the ground or water with waste, do not dispose of

waste into the environment. Soiled packaging : Empty container completely. Keep label(s) on container.

Give to a certified disposal contractor.

SECTION 14: TRANSPORT INFORMATION

Transport product in compliance with provisions of the ADR for road, RID for rail, IMDG for sea and

ICAO/IATA for air transport (ADR

2007 - IMDG 2006 - ICAO/IATA 2007). UN1759=CORROSIVE SOLID, N.O.S.

ADR/RID Class Code Pack gr. Label Ident. LQ Provis.

8 C10 III 8 80 LQ24 274

IMDG Class 2°Label Pack gr. LQ EMS Provis.

8 - III 5kg F-A, S-B 223 274 944

IATA Class 2°Label Pack gr. Passager Passager Cargo Cargo note

8 - III 822 25Kg 823 100KG -

8 - III 822 5Kg - - -

Page 32: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 32 OF 33

SECTION 15 : REGULATORY INFORMATION

This preparation was classified in compliance with the directive known as <All preparations>

1999/45/EC and its adaptations. In addition directive 2004/73/EC with the 29° adaptation of

directive 67/548/EEC (Hazardous substances) have been taken into account. This product is not

classed as flammable.

Packaging < 125 ml.

Preparation classification:

Corrosive Dangerous for the environment

Contains: IODOFORM

Particular hazards associated with the preparation and safety recommendations: R 50/53 Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic

environment.

R 34 Causes burns.

S 26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

S 36/37/39 Wear suitable protective clothing, gloves and eye/face protection. S 45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where

possible).

S 61 Avoid release to the environment. Refer to special instructions/Safety data sheets.

S 60 This material and its container must be disposed of as hazardous waste.

S 57 Use appropriate container to avoid environmental contamination.

SECTION 16: OTHER INFORMATION

Since the user's working conditions are not known by us, the information supplied on this safety data

sheet is based on our current level of knowledge and on national and community regulations.

The product must not be used for any purposes other than those specified under heading 1 without

first obtaining written handling instructions. It is at all times the responsibility of the user to take all necessary measures to comply with legal

requirements and local regulations.

The information given on this safety data sheet must be regarded as a description of the safety

requirements relating to our product and not a guarantee of its properties

Full text of risk phrases appearing in section 3:

R 34 Causes burns.

Page 33: MATERIAL SAFETY DATA SHEET - Prevest Denpro Limited › prevestadmin › files › ... · 2019-08-29 · MATERIAL SAFETY DATA SHEET PAGE 1 OF 33 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET

PAGE 33 OF 33

R 50/53 Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic

environment.


Recommended