MATERIALS FOR WIREBOND PACKAGING€¦ · leadframe packaging materials With more than three decades...

MATERIALS FOR WIREBOND PACKAGINGLAMINATE AND LEADFRAME SOLUTIONS

INTRODUCTIONSemiconductor packaging continues to evolve, with semiconductor devices becoming more functional, powerful and integrated. Die sizes are shrinking, wafers are thinner than ever, and the lines between traditional semiconductor packaging and advanced form factors like system-in-package and system-in-module are increasingly blurred. Varying device configurations are addressing the new era of semiconductor manufacturing, with flip-chip and wirebond interconnection methodologies as the most prevalent. And, while flip-chip packaging technology is often preferred for small form factors, wirebond ICs still rule the industry in terms of volume and reliability. According to market research reports, wirebond IC packaging accounted for the majority of all advanced packaging integrated circuit technology, dominating the number of die in units shipped.

For packaging specialists and device designers, the flexibility, cost and existing infrastructure of wirebonding remain among the technology’s primary advantages and fuel its stronghold status. Future growth for the wirebond sector will be largely driven by increased semiconductor use in the automotive electronics sector.

CONTENTS

2 | Contents Introduction | 3

Introduction .............................................................................................................................................................. 3

Product Portfolio ..................................................................................................................................................... 4

Laminate Packaging Materials ............................................................................................................................ 5

Die Attach Pastes .................................................................................................................................................. 6

Die Attach Films ................................................................................................................................................... 8

Wafer Backside Coatings ...................................................................................................................................... 9

Printable BOC Die Attach Materials .................................................................................................................. 10

Encapsulants ........................................................................................................................................................ 12

Solder Pastes ........................................................................................................................................................14

Leadframe Packaging Materials ......................................................................................................................... 15

Die Attach Pastes .................................................................................................................................................16

Die Attach Films ................................................................................................................................................. 20

Wafer Backside Coatings .................................................................................................................................... 22

Solder Pastes ....................................................................................................................................................... 24

Laminate and Leadframe Packaging Materials ............................................................................................. 25

Package Level EMI Shielding ............................................................................................................................. 26

Appendix ..................................................................................................................................................................27

LAMINATE PACKAGING MATERIALSHenkel’s range of BMI-based adhesives enabled the proliferation of array type packaging when it was first introduced. Continuing this tradition, Henkel is facilitating advances in IC packaging with new materials systems designed for high performance and reliability in small formats, such as LGA devices, to very large format system-in-package and system-in-module technology. Whether paste, liquid or film, Henkel’s materials are engineered for maximum efficiency and are developed in conjunction with leading-edge applications, giving semiconductor specialists the peace of mind to confidently integrate our materials for the most demanding processes and requirements. For challenging applications such as sensor technology, innovative materials with tightly-controlled physical characteristics like modulus of elasticity help avoid any compromise of parametric performance of packaged devices.

SolderPaste

EMI ShieldingMaterial

Encapsulant

Die AttachFilm

WaferBacksideCoating

Die AttachPaste

4 | Product Portfolio Die Attach Paste Adhesives | 5 Laminate Packaging Materials | 5

PRODUCT PORTFOLIO

MATERIALSFOR

WIREBONDPACKAGING

LAMINATEPACKAGING

LEADFRAMEPACKAGING

DIE ATTACH PASTES

ENCAPSULANTS

SOLDER PASTES

WAFER BACKSIDE COATINGS

DIE ATTACH PASTES

DIE ATTACH FILMS


SOLDER PASTES

DIE ATTACH FILMS

EMI SHIELDING MATERIALS

PRINTABLE BOC DIE ATTACH MATERIALS

LAMINATE ANDLEADFRAMEPACKAGING

Addressing the requirements for both laminate and leadframe wirebond packages, Henkel has developed a comprehensive portfolio of advanced materials for various wirebond requirements – from smaller die-to-pad ratios to thinner bond lines to low stress to high temperature capability and robust adhesion. A wide range of die attach pastes and films, encapsulants, solder pastes, package-level EMI shielding materials, and alternative wafer backside coating (WBC) die attach solutions deliver the process adaptability, cost-effectiveness and in-field reliability necessary for today’s advanced wirebond ICs.

Die Attach Pastes | 7

DIE ATTACH PASTES

6 | Die Attach Pastes

A broad selection of electrically non-conductive and conductive LOCTITE® ABLESTIK die attach paste formulations provide the reliability and performance today’s high-density laminate packages demand. Each package type – from BGAs to LGAs to SmartCards – has different requirements, which is why Henkel has developed a suite of products that cater to the unique needs of laminate-based devices. Henkel die attach pastes offer a low modulus for stress reduction and warpage elimination, as well as bismaleimide (BMI) formulations for low moisture absorption to avoid package cracking during high temperature processing.

Die AttachPastesLGA

D I E AT TAC H PA S T E S ( DA P ) FO R W I R E B O N D L AM I N AT E PAC K AG I N G

BGA, PBGA, FBGA and CBGA

ElectricallyConductive

LOCTITEABLESTIK

2000

LOCTITEABLESTIK

2100A

LOCTITEABLESTIK

2300

LOCTITEABLESTIK2700HT


LOCTITEABLESTIK

2025D

LOCTITEABLESTIK

2053S

LOCTITEABLESTIK

2025D

LOCTITEABLESTIK

2053S

LOCTITEABLESTIK

ABP 2030SCR

LOCTITEABLESTIK

ABP 2032S

LOCTITEABLESTIK2033SC

LOCTITEABLESTIK

ABP 2035SCR

LOCTITEABLESTIK

2100A

LOCTITEABLESTIK

2300


ElectricallyNon-conductive




SmartCard (COB)

ELECTRICALLY CONDUCTIVE DIE ATTACH PASTES (DAP)

PRODUCT DESCRIPTION KEY ATTRIBUTESDIE SIZE (mm)

SUBSTRATE FINISH

MOISTURE SENSITIVITY LEVEL, MSL

VOLUME RESISTIVITY (Ohm ·cm)

THERMAL CONDUCTIVITY

(W/m ·K)

RECOMMENDED CURE

LOCTITEABLESTIK2000

Ag-filled die attach adhesive

• Low bleed• Low stress• Ultra-low moisture absorption• Fast oven cure with no voids

≤ 12 x 12Solder mask

or AuL2 260°Ccapable

5.0 x 10-4 1.230 min. ramp and

15 min. hold at 175°C

LOCTITEABLESTIK2100A


• Low bleed• Low stress• Oven cure



5.0 x 10-2 1.230 min. ramp and


LOCTITEABLESTIK2300


• Low bleed• Low stress• Excellent dispensability• Low voiding• Oven cure



5.0 x 10-2 0.630 min. ramp and




• Excellent bleed performance• Long work life• Strong hot/wet adhesion

to Au• Ideal for small needle

dispensing• Oven cure

≤ 3 x 3Solder mask,

Ag or AuL3 260°Ccapable

3.0 x 10-5 11.030 min. ramp and

30 min. hold at 175°C in nitrogen

LOCTITEABLESTIKABP 2030SCR


• Low stress• Compatible with dam & fill

encapsulants• Excellent dispensing

performance for high throughput application

• Snap cure


Ag, Au or plastics

L3 260°Ccapable

2.0 x 10-4 2.0 120 sec. at 120°C

LOCTITEABLESTIKABP 2032S

Ag-filled, epoxy die attach adhesive

• Good adhesion to a variety of substrates

• Good dispensing characteristics

• Low temperature oven cure


Ag, Au, steel or plastics

L3 260°Ccapable

2.0 x 10-4 1.0 60 min. at 80°C

ELECTRICALLY NON-CONDUCTIVE DIE ATTACH PASTES (DAP)


SUBSTRATE FINISH


MODULUSAT 25°C (MPa)


(W/m ·K)

RECOMMENDED CURE

LOCTITEABLESTIK2025D

Silica-filled die attach adhesive

• Low bleed• Very low stress• Red color for vision

recognition• Good adhesion to a variety of

substrates• Oven cure

≤ 8 x 8Solder mask, Cu, Ag or Au

L3 260°Ccapable

407 0.430 min. ramp and


LOCTITEABLESTIK2033SC


• Long work life• Low bleed• Optimized rheology• Snap cure


Ni, Cu, Ag or Au

L3 260°Ccapable

2,100 0.35 90 sec. at 110°C

LOCTITEABLESTIKABP 2035SCR


• Low stress• Compatible with dam & fill

encapsulants• Excellent dispensing

performance for high throughput application

• Snap cure or low temperature oven cure



1,500 1.0 2 min. at 120°C (snap)

LOCTITEABLESTIK2053S

Polymer-filled, epoxy die attach adhesive

• Non-conductive• Low stress• Red color

5 x 5Solder mask


87 0.1930 min. at 175°C + 15 minutes at 175°C

Die Attach Films | 9

DIE ATTACH FILMS

8 | Die Attach Films

Henkel is the established leader in die attach film technology for laminate-based devices. Electrically non-conductive die attach films provide stability and support for thinner wafer handling and facilitate thin bond lines within multi-die stacks for greater functionality. Compatibility with both copper and gold wire and various wafer grinding methods lend process versatility to these high performance products. Henkel’s formulation expertise led to the development of the market’s first viable electrically conductive die attach film, which is an ideal solution for devices such as Logic ICs, MOSFETs and RF, where low stress, high adhesion, tight die-to-pad clearance and high reliability are required.

D I E AT TAC H F I L M S FO R W I R E B O N D L AM I N AT E PAC K AG I N G

LOCTITE®

ABLESTIKCDF 600P Series

Memory, Logic, MEMS and Sensors

LOCTITEABLESTIK

ATB F100E Series

LOCTITEABLESTIK

ATB 100 Series

LOCTITEABLESTIK

ATB 100HA Series

LOCTITEABLESTIK

ATB 100U Series

LOCTITEABLESTIK

ATB 100US Series

Electrically Non-conductiveElectricallyConductive

Logic IC,MOSFET and RF

ELECTRICALLY CONDUCTIVE DIE ATTACH FILMS (CDAF)

PRODUCT DESCRIPTION KEY ATTRIBUTESFILM

THICKNESS (μm)



(W/m ·K)

IN-PACKAGE THERMAL

RESISTANCE (K/W)

LOCTITEABLESTIKCDF 600P Series


• Low stress and excellent wetting for large die• Compatible with various metal surfaces, including solder• Recommended for thin wafer handling applications• Oven cure

25L2 260°Ccapable

1 2.1

PRODUCT DESCRIPTION KEY ATTRIBUTESDICING TAPE

FILM THICKNESS

(μm)

WAFER THICKNESS

(μm)



LOCTITEABLESTIKATB 100 Series

Silica-filled, rubberized epoxy die attach adhesive

• Compatible with Cu wire or Au wire packages• Good adhesion onto low density fiberboard (LDF)• Compatible with Stealth Dicing Before Grind (SDBG)

process • Oven cure

Non-UV 15, 20, 25 or 30 ≥ 75L2 260°Ccapable

1,170

LOCTITEABLESTIKATB 100HA Series

Silica-filled, epoxy die attach adhesive

• Consistent dicing and die pickup for large die applications

• Compatible with Stealth Dicing Before Grind (SDBG)process

• SkipCure

UV/Non-UV

5, 10, 15, 20, 25 or 30

≥ 50L1 260°Ccapable

2,299

LOCTITEABLESTIKATB 100U Series


• Compatible with Cu wire or Au wire packages • Compatible with Stealth Dicing Before Grind (SDBG)

process• Fast oven cure

Non-UV5, 10, 15, 20, 25

or 30≥ 75

L2 260°Ccapable

875

LOCTITEABLESTIKATB 100US Series


• Long thermal budget (4 hr. at 175°C)• Consistent dicing and die pickup for large die

applications• SkipCure during molding process

UV/Non-UV

5, 10, 15, 20, 25 or 30


1,277

ELECTRICALLY NON-CONDUCTIVE DICING DIE ATTACH FILMS (DDF)

10 | Wafer Backside Coatings Printable BOC Die Attach Materials | 11

WAFER BACKSIDE COATINGS PRINTABLE BOC DIE ATTACH MATERIALS

Print BOC Material

Wirebond Material

Die

ELECTRICALLY NON-CONDUCTIVE WAFER BACKSIDE COATINGS (WBC)


SUBSTRATE FINISH


MODULUS AT 25°C (MPa)

CTE (ppm/°C) RECOMMENDED CUREBelow T

gAbove T

g

LOCTITEABLESTIKWBC 8901UV

Die attach wafer backside coating adhesive

• Wide process windows• 5 to 60 µm bondline control• Low viscosity before B-stage• Can be spray coated on Dicing

Before Grinding (DBG) wafers• UV B-stage and oven cure

≤ 1 x 1Solder mask, Cu, Ag or Au

L2 260°C capable

3,585 45 142

15 min. ramp and 30 min. hold at 90°C + 4 min. ramp and 45 min. hold at 120°C

WA F E R B AC K S I D E COAT I N G SFO R W I R E B O N D L AM I N AT E PAC K AG I N G

Stacked Memory, Logic CSP and MEMS

Electrically Non-conductive

LOCTITE®

ABLESTIKWBC 8901UV

Wafer Backside Coating is a unique process that facilitates automated application of die attach adhesive at the wafer-level followed by B-staging to form a die attach film. Applied by spray coating, Henkel’s Wafer Backside Coatings enable process speed, thickness control and material uniformity. Following thermal or UV B-staging and wafer dicing, die attach is achieved via heat and pressure to produce a consistent bond line and small, controlled fillets. Wafer Backside Coating adhesives are ideal for die attach applications where fillet control is critical.

PRINTABLE BOC DIE ATTACH MATERIALS

PRODUCT DESCRIPTION KEY ATTRIBUTES

VISCOSITY, BROOKFIELD CP51 AT 25°C AND 5 RPM

(cP)

GLASS TRANSITION

TEMPERATURE, T

g, BY TMA (°C)

CTE (ppm/°C) RECOMMENDED B-STAGE

CONDITION

CURE SCHEDULEBelow

Tg

Above Tg

LOCTITE ABLESTIK 6200

B-stageable die attach adhesive

• Stencil printing• Low moisture uptake• Low bleed• Ideal for chip scale packages

where tolerance and bleed need to be minimized

• Oven cure• Designed for flex or laminate

based substrates

21,000 -10 94 237 60 min. at 120°C30 min. ramp + 60 min. soak at

175°C

LOCTITE ABLESTIK 6202C


• Stencil printing• Low warpage• Ideal for chip scale packages


• Oven cure• Recommended for large die sizes• Designed for laminate based substrates

28,000 40 70 350 1 hr. at 125°C30 min. ramp + 60 min. soak at

175°C

LOCTITE ABLESTIK 6202C-X


• Small particle size• Stencil printing• Low warpage• Ideal for chip scale packages


• Oven cure• Recommended for large die sizes• Designed for laminate based

substrates

30,000 40 70 232

30 min. ramp + 90 min. soak at 125°C + 30 min.

ramp down to 25°C in vented magazine in oven with good

air flow

30 min. ramp + 90 min. soak at 90°C + 30 min.

ramp and 60 min. soak at 175°C in

vented magazine in oven with good air flow

P R I N TA B L E B O C D I E AT TAC H A D H E S I V E S FO R W I R E B O N D L AM I N AT E PAC K AG I N G

Memory

B-Stage Die Attach Material

LOCTITE ABLESTIK 6202C

LOCTITE ABLESTIK 6202C-X

LOCTITE ABLESTIK 6200

As board-on-chip (BOC) – also known as substrate-on-chip – packaging emerges as the dominant chip-scale packaging configuration for DRAM devices, die attach materials must deliver with precise control of bondline thickness and die tilt, minimal fillet formation and no contamination of wire bond pads. Henkel’s B-stage printable adhesives offer a more cost-effective solution than conventional adhesive films, providing the robust performance of film at a paste price point. The portfolio of LOCTITE ABLESTIK materials for BOC applications offers high UPH, printable formulations with low flow, controlled bondlines, minimized tolerance and bleed, as well as long storage and work lives.

12 | Encapsulants Package Level EMI Shielding | 13

ENCAPSULANTSENCAPSULANTS

PRODUCT DESCRIPTION KEY ATTRIBUTES APPLICATIONVISCOSITY

AT 25°C (cP)

GLASS TRANSITION

TEMPERATURE, T

g (°C)

CTE,BELOW

Tg

(ppm/°C)

RECOMMENDED CURE

Dam

LOCTITE ECCOBOND FP4451

Epoxy dam encapsulant

• Stable and consistent thixotropy with minimal slumping

• Excellent pressure pot performance on live devices up to 500 hr.

• Designed for use with fill encapsulant LOCTITE ECCOBOND FP4450

• Oven cure

BGA and memory 860,000 at 4 rpm

155 2230 min. at 125°C + 90

min. at 165°C

LOCTITE ECCOBOND FP4451TD

Epoxy dam encapsulant

• Ionically clean• High thixotropy with high height to width

aspect ratio (0.7)• Excellent chemical resistance and thermal

stability• Designed for use with fill encapsulant LOCTITE ECCOBOND FP4450• Oven cure

BGA and memory 300,000 at 20 rpm

150 2130 min. at 125°C + 90

min. at 165°C

Fill


Epoxy fill encapsulant

• Low stress and high flow with reduced warpage and cracking

• Low CTE• Excellent thermal shock and moisture

resistance• Halogen-free• Oven cure

Stress-sensitive devices and

severe automotive environments

20,000 at 20 rpm

175 181 hr. at 125°C

+ 1 hr. at 180°C



• Low stress and relatively high flow• Good moisture resistance and excellent

chemical resistance• Excellent pressure pot performance on live

devices up to 500 hr. • Oven cure

Automotive, BGA, memory, COB, SiP

and SmartCard

43,900 at 20 rpm

155 2230 min. at 125°C

+ 90 min. at 165°C

LOCTITE ECCOBOND FP4450HF


• Excellent chemical, corrosion and moisture resistance

• High thermal stability• Very high flow and fine filler (max. particle

size 25 μm)• Oven cure

Automotive, BGA, memory, COB, SiP

and SmartCard

32,000 at 20 rpm

164 2130 min. at 125°C

+ 90 min. at 165°C



• MSL3 260°C capable• High reliability• Excellent flow good for fine pitch wires and

deep cavities• 260°C reflow capability for Pb-free

applications• Oven cure

BGA, CSP and full array on low

temperature co-fired ceramic

(LTCC)

42,000 at 10 rpm

148 1830 min. at 125°C

+ 90 min. at 165°C



• Low stress• Low CTE• Easy to dispense• Excellent chemical resistance and thermal

stability• Oven cure

Automotive, BGA, memory, COB, SiP,

SmartCard and chip array ceramic

packages

130,000at 20 rpm

150 111 hr. at 125°C

+ 90 min. at 165°C



• Fine filler• Low stress and low CTE• Excellent chemical resistance and thermal

stability• Jettable• Oven cure

MEMS and chip array ceramic

packages

32,000 at 20 rpm

146 1330 min. at 125°C

+ 90 min. at 165°C



• MSL2 260°C capable• Low warpage• Excellent flow good for fine pitch wires and

deep cavities• Oven cure

BGA, CSP and full array on low

temperature co-fired ceramic

(LTCC)

80,000 at 10 rpm

50 2060 min. at 120°C

+ 120 min. at 165°C

Glob Top


Epoxy glob top encapsulant

• Low CTE for improved thermal cycling• Thixotropic• Excellent moisture and chemical resistance• Oven cure

COB and plastic PGA

220,000 at 2 rpm

174 28 4 hr. at 150°C

Die AttachPastes

Fill

E N C A P S U L A N T S FO R W I R E B O N D L AM I N AT E PAC K AG I N G

Dam

LOCTITE®

ECCOBONDFP4451

LOCTITEECCOBOND

FP4651

LOCTITEECCOBOND

FP4654

LOCTITEECCOBOND

FP4660

LOCTITEECCOBONDUV8800M

LOCTITEECCOBONDFP4450HF

LOCTITEECCOBOND

FP4470

LOCTITEECCOBONDFP4451TD

LOCTITEEO7021

LOCTITEECCOBOND

FP4323

LOCTITEECCOBOND

FP4460

LOCTITEECCOBOND

FP0087

LOCTITEECCOBOND

FP4450

LOCTITEECCOBOND

FP4802

Glob Top

Protection from the effects of mechanical damage and corrosion is essential for the long-term reliability of semiconductor devices. With a range of products to tackle growing application demands, Henkel’s advanced encapsulant materials in both dam/fill and glob top systems meet the most stringent JEDEC-level testing, offering outstanding performance in formulations that simplify processing through robust dispensing characteristics and flexible cure mechanisms. Henkel’s high-purity epoxy encapsulant solutions provide device safeguarding and manufacturing confidence.

14 | Solder Paste Leadframe Packaging Materials | 15

S O L D E R PA S T E S FO RW I R E B O N D L AM I N AT E PAC K AG I N G

LOCTITEHF 212

LOCTITE®

HF 250DPLOCTITEGC 10

PrintableDispensable

SiP

SOLDER PASTES

Proper solder alloy formulation is vital for laminate-based packages, as the melting point must be tightly controlled to maintain the integrity of the organic substrate. Award-winning halogen-free, lead-free solder paste materials offer low-voiding performance and can be processed at lower reflow temperatures to align with the requirements of wirebond laminate package processing.

LEADFRAME PACKAGING MATERIALS

With more than three decades of semiconductor materials development leadership, Henkel has formulated a comprehensive line of products that satisfy the requirements of all forms of leadframe-based packaging. Novel material systems are focused on providing the highest levels of JEDEC MSL performance, the ability to accommodate increasingly demanding requirements for form factor and bond line control, and optimize electrical and thermal performance. Innovations include tighter particle size control, B-stage and controlled flow adhesives, and conductive die attach films that enable multi-chip placement of high power die on a single die pad without increasing package dimensions – all of which are delivering new capability for next-generation devices. For higher power applications, materials with improved in-package thermal performance and electrical conductivity approaching that of pure silver have been introduced. And, as copper wirebonds become the standard across the industry, Henkel’s non-conductive and conductive die attach paste and film formulations meet these new demands.

Die Attach Paste

Die Attach Film

SOLDER PASTES

PRODUCT DESCRIPTION KEY ATTRIBUTES ALLOYPARTICLE SIZE DISTRIBUTION

VISCOSITY AT 25°C

(cP)

REFLOW ATMOSPHERE

IPC J-STD 004B CLASSIFICATION

SHELF LIFE

Dispensable

LOCTITEHF 250DP

Halogen-free, Pb-free, no-clean solder paste

• Low voiding • Exceptional dot-to-dot consistency• High-speed dispense capability with zero slump• Colorless residues

SAC387 Type 5160,000at 5 rpm

Nitrogen ROL012 months up to -18°C

Printable

LOCTITEGC 10

Temperature-stable, halogen-free, Pb-free, no-clean solder paste

• Low voiding• Exceptionally long stencil life and abandon time• Outstanding paste transfer efficiency• Excellent wetting and coalescence in air• Suitable for high density, small to large boards

SAC305Type 3, 4, 4.5 (4A)

and 5

900,000 – 933,000 at 5 rpm

Designed for air; suitable with

nitrogenROL0

12 months up to 26.5°C

LOCTITEHF 212

Halogen-free, Pb-free, no-clean solder paste

• Low voiding• Extended stencil life and abandon time• Printing, pin-in-paste and enclosed head print capability• Excellent wetting and fine pitch coalescence• Suitable for medium to large boards

90iSC96S

SAC0307SAC305SAC387

Type 3, 4, 4.5 (4A) and 5

750,000 – 900,000at 5 rpm

Air and nitrogen ROL06 months

at 0°C – 10°C

16 | Die Attach Pastes Die Attach Pastes | 17

Process flexibility and superior performance underscore Henkel’s complete portfolio of die attach pastes for leadframe devices. Incorporated into applications such as automotive electronics, where temperature control and unfailing function are critical, LOCTITE ABLESTIK die attach pastes deliver high thermal conductivity and high reliability. Robust adhesion to various metal surfaces including palladium, copper, silver, gold and PPF along with proven low-bleed formulas make Henkel’s die attach materials the products of choice for leadframe packaging specialists.

Die AttachPastes

QFN QFPDie Attach

PastesSOIC, TSOP and TSSOP

D I E AT TAC H PA S T E S ( DA P ) FO R W I R E B O N D L E A D F R AM E PAC K AG I N G

Discrete and DIP


LOCTITE®

ABLESTIK8200TI

LOCTITEABLESTIK8200TI

LOCTITEABLESTIK

8352L

LOCTITEABLESTIK

8900NCM

LOCTITEABLESTIK

8900NCM

LOCTITEABLESTIK

ABP 8910T

LOCTITEABLESTIK

84-1LMISR4

LOCTITEABLESTIK

8600

LOCTITEABLESTIK

ABP 8060T

LOCTITEABLESTIK

QMI529HT-LV

LOCTITEABLESTIK

3230

LOCTITEABLESTIK

3230

LOCTITEABLESTIK

3290P

LOCTITEABLESTIK

2025D

LOCTITEABLESTIK

2025D

LOCTITEABLESTIK

2025D

LOCTITEABLESTIKABP 8611

LOCTITEABLESTIK

8390

LOCTITEABLESTIK

8302

LOCTITEABLESTIK

8302

LOCTITEABLESTIK

8302

LOCTITEABLESTIK

8290

LOCTITEABLESTIK

8290

LOCTITEABLESTIK

8390

LOCTITEABLESTIK

8290

LOCTITEABLESTIKFS 849-TI





LOCTITEABLESTIK

QMI529HT-LV

LOCTITEABLESTIKQMI519


LOCTITEABLESTIK

ABP 8064T

LOCTITEABLESTIK

ABP 8062T/ABP 8064T

LOCTITEABLESTIK

ABP 8065T/ABP 8066T

LOCTITEABLESTIK

ABP 8068TA/ABP 8068TB

LOCTITEABLESTIK


LOCTITEABLESTIK


LOCTITEABLESTIK

QMI529HT-LV

LOCTITEABLESTIK

2053S

LOCTITEABLESTIK

ABP 84-3JT

LOCTITEABLESTIK

2053S

LOCTITEABLESTIKSSP 2020










LOCTITEABLESTIK

ABP 8065T/ABP 8066T

DIE ATTACH PASTES

ELECTRICALLY CONDUCTIVE DIE ATTACH PASTES (DAP)


SUBSTRATE FINISH




(W/m ·K)

RECOMMENDED CURE

LOCTITEABLESTIK3230


• Low stress• Excellent adhesion to Cu• Oven cure

≤ 8 x 8 Cu or AgL3 260°Ccapable

5.0 x 10-2 0.630 min. ramp and


LOCTITEABLESTIK3290P


• Medium modulus• Low outgassing• High reliability• Snap or oven cure

≤ 5 x 5 Cu, Ag or PPFL2 260°Ccapable

2.0 x 10-2 0.8180 sec. to peak

240°C (snap)



• No bleed• Excellent adhesion to pre-

plated finishes (PPF)• Oven or snap cure

≤ 5 x 5Cu, Ag, PPF


5.0 x 10-5 3.5180 sec. to peak

220°C (snap)

LOCTITEABLESTIK8290


• Low stress • Low bleed• Excellent adhesion to Cu• Oven cure



8.0 x 10-3 1.630 min. ramp and


LOCTITEABLESTIK8302


• Low stress• Excellent hot/wet adhesion• Excellent peel strength• Low moisture absorption• Oven cure


1.0 x 10-4 0.830 min. ramp and


LOCTITEABLESTIK8352L


• Low stress• Minimal voiding• Good bleed performance• Good adhesion to multiple

metal surfaces• Oven or snap cure

≤ 8 x 8 Cu, Ag, PPF


5.0 x 10-5 5.5120 sec. to peak

220°C (snap)

LOCTITEABLESTIK8390


• Low bleed• Low condensable volatiles• Moderately stress absorbing• Excellent dispensability• In-line oven snap cure or oven

cure

≤ 5 x 5 Pd or AgL3 260°Ccapable

8.0 x 10-4 1.880 sec. to peak 220°C

(snap)

LOCTITEABLESTIK84-1LMISR4


• Excellent dispense capability• Long work life• High throughput• Box oven cure

≤ 3 x 3 Ag, PPF or AuL1 260°Ccapable

≥ 2.0 x 10-4 2.5 1 hr. at 175°C

LOCTITEABLESTIK8600

Ag-filled, acrylate die attach adhesive

• Low bleed• Excellent in-package thermal performance• Oven or snap cure



1.0 x 10-3 > 460 sec. to peak 220°C

(snap)

18 | Die Attach Pastes Die Attach Pastes | 19

ELECTRICALLY CONDUCTIVE DIE ATTACH PASTES (DAP) (CONTINUED)

PRODUCT DESCRIPTION KEY ATTRIBUTESDIE SIZE

(mm)SUBSTRATE

FINISH




(W/m ·K)

RECOMMENDED CURE

LOCTITEABLESTIKABP 8060T

Ag-filled, BMI hybrid die attach adhesive

• High modulus• High die shear

strength• Hydrophobic• Oven cure



2.5 x 10-5 2045 min. ramp and 60 min. hold at

200°C



• Hydrophobic• Electrically conductive• Thermally conductive• Stable at high

temperatures

3 x 3 Ag or PPF L3 260°Ccapable

5 x 10-5 24

45 min. ramp from 25°C to 200°C +

30 min. at 200°C in N

2 or air oven



• Medium modulus• Low outgassing• Oven cure

3 x 3 – 8 x 8Cu, Ag, PPF


2.0 x 10-5 2260 min. ramp and



Ag-filled, epoxy hybrid die attach adhesive

• No channel void issue• High die shear

strength• Dispensable silver

paste• Oven or snap cure

≤ 2 x 2 Ag or AuL3 260°Ccapable

3.0 x 10-5 10

30 min. ramp and 60 min. hold at

185°C in nitrogen (oven)



• Long open time• High die shear

strength• Hydrophobic• Low outgassing• Oven cure




175°C

LOCTITEABLESTIKABP 8068TA

Ag-filled, semi-sintering die attach adhesive

• One component• Low temperature

sintering• Best in-class

electrical and thermal performance

• Excellent workability• High reliability



9.0 x 10-6 110

20 min. to 130C, hold 30 min.,

15 min. to 200°C, hold 1 hr.

LOCTITEABLESTIKABP 8068TB

Ag-filled, semi-sintering die attach adhesive with resin bleed control

• No resin bleed out• Low temperature

sintering• Best in-class

electrical and thermal performance

• Excellent workability• High reliability



7.0 x 10-6 100

20 min. to 130C, hold 30 min.,

15 min. to 200°C, hold 1 – 2 hr.



• Excellent in-package thermal performance

• Low bleed• Medium modulus• Low outgassing• Oven cure


2.0 x 10-5 7.815 min. ramp and


LOCTITEABLESTIKQMI519

Ag-filled, BMI/acrylate die attach adhesive

• Excellent dispense capability

• Long work life• High throughput• Hydrophobic• Fast oven cure or

SkipCure



1.0 x 10-4 3.8≥ 10 sec. at 200°C

(SkipCure)

LOCTITEABLESTIKQMI529HT-LV


• Good dispensing characteristics

• Stable at high temperatures

• Hydrophobic• Excellent adhesive

strength• Oven cure

≤ 8 x 8 Ag or PPFL2 260°Ccapable


175°C


Ag sintering die attach adhesive

• High die shear strength• Robust dispense

and stencil print performance

• Good workability• High-temperature

sinter with or without pressure


4.8 x 10-5 > 100

10 min. ramp and 60 min. hold at

250°C (pressureless

sintering)

ELECTRICALLY NON-CONDUCTIVE DIE ATTACH PASTES (DAP)


SUBSTRATE FINISH




(W/m ·K)

RECOMMENDED CURE

LOCTITEABLESTIK2025D


• Low bleed• Very low stress• Red color for vision recognition• Oven cure

≤ 8 x 8 Cu, Ag or AuL3 260°Ccapable



LOCTITEABLESTIK8900NCM

PTFE-filled, epoxy die attach adhesive

• Low bleed• Low voiding• Moderately stress absorbing• Excellent dispense capability• Contains no category 3

carcinogenic, mutagenic, or reprotoxic (CMR) substances

• Oven cure

≤ 8 x 8Pd, Cu, Ag or

PPFL3 260°Ccapable




BMI hybrid die attach adhesive

• Excellent dielectric properties• Suitable for Cu wire or Au wire

bonding• High modulus at high

temperatures• Oven cure


5,000 0.730 min. ramp and



Alumina-filled, BMI hybrid die attach adhesive

• Medium modulus• High reliability• Oven cure


8,870 1.330 min. ramp and


LOCTITE ABLESTIK ABP 84-3JT

Non-conductive, BMI hybrid die attach adhesive

• Non-conductive• Insulating• Good adhesion to Cu and Ag• No resin bleed-out• Snap curable• Contains 1 mil spacers for better

bond line and stress control

≤ 5 x 5 Ag or CuL3 260°Ccapable

2,950 0.630 min. ramp to

175°C + 60 min. at 175°C in N

2 oven

LOCTITEABLESTIK2053S

Polymer-filled, epoxy die attach adhesive

• Non-Conductive• Low stress• Red color

5 X 5Solder mask


87 0.1930 min. at 175°C +

15 min. at 175°C

20 | Die Attach Films Die Attach Films | 21

DIE ATTACH FILMS

D I E AT TAC H F I L M S FO R W I R E B O N D L E A D F R AM E PAC K AG I N G

Logic IC, MOSFET and RF SOIC, TSOP and TSSOP

LOCTITEABLESTIK

ATB 100 Series

LOCTITEABLESTIK

CDF 200P Series

LOCTITEABLESTIK

CDF 500P Series

LOCTITEABLESTIK

CDF 700P Series

LOCTITEABLESTIK

CDF 300P Series

LOCTITEABLESTIK

CDF 600P Series

LOCTITEABLESTIK

CDF 800P Series

LOCTITEABLESTIK

ATB 100U Series

LOCTITEABLESTIK

ATB 100HA Series

LOCTITEABLESTIK

ATB 100US Series

LOCTITEABLESTIK

ATB 100HA Series

LOCTITEABLESTIK

ATB F100E Series

LOCTITEABLESTIK

ATB F100E Series

LOCTITEABLESTIK

ATB 100 Series

LOCTITEABLESTIK

ATB 100 Series

Electrically Conductive Electrically Non-conductiveElectrically

Non-conductiveElectrically

Non-conductive

QFN QFP

LOCTITEABLESTIK

ATB 100HA Series

Henkel’s die attach film solutions for leaded devices integrate the unique properties required for a variety of leadframe packages – from QFNs to Logic ICs to TSOPs. Available in both non-conductive and conductive formulations, Henkel’s broad die attach film product line has been engineered to account for numerous application-specific requirements such as wire type compatibility, die size capability, wafer grinding techniques, challenging die-to-pad ratios, higher density packaging, wafer thickness limitations and cure mechanisms.

ELECTRICALLY NON-CONDUCTIVE DICING DIE ATTACH FILMS (DDF)

PRODUCT DESCRIPTION KEY ATTRIBUTESDICING TAPE

FILM THICKNESS

(μm)

WAFER THICKNESS

(μm)



LOCTITEABLESTIKATB 100 Series


• Compatible with Cu wire or Au wire packages• Excellent wetting• Compatible with Stealth Dicing Before Grind (SDBG) process• Oven cure

Non-UV15, 20, 25

or 30≥ 75

L2 260°Ccapable

1,170

LOCTITEABLESTIKATB 100HA Series


• Consistent dicing and die pickup for large die applications• No passivation damage• Compatible with Stealth Dicing Before Grind (SDBG) process• SkipCure

UV/Non-UV5, 10, 15, 20,

25 or 30≥ 50

L1 260°Ccapable

2,299

LOCTITEABLESTIKATB 100U Series


• Compatible with Cu wire or Au wire packages • No passivation damage • Compatible with Stealth Dicing Before Grind (SDBG) process• Fast oven cure

Non-UV5, 10, 15, 20,

25 or 30≥ 75

L2 260°Ccapable

875

LOCTITEABLESTIKATB 100US Series


• Consistent dicing and die pickup for large die applications• No passivation damage• Long thermal budget (4 hr. at 175°C)• SkipCure during molding process

UV/Non-UV5, 10, 15, 20,

25 or 30≥ 50

L2 260°Ccapable

1,277

LOCTITEABLESTIKATB F100E Series


• Suitable for small to large die• Excellent workability for below 3 mm x 3 mm die• Long work life (4 months before and after lamination)• Compatible with Stealth Dicing Before Grind (SDBG) process• Film over wire (FoW) and film over die (FoD) applications• Oven cure

UV/Non-UV25

FoW: 35 – 80FoD: 90 – 150


5,256

ELECTRICALLY CONDUCTIVE DIE ATTACH FILMS (CDAF)

PRODUCT DESCRIPTION KEY ATTRIBUTESFILM

THICKNESS (μm)



(W/m ·K)

IN-PACKAGE THERMAL

RESISTANCE (K/W)



• Suitable for small die• Recommended for thin wafer handling applications• Oven cure

15 or 30L1 260°Ccapable

2.3 1.5



• Suitable for small die• High adhesion• Good wetting• Oven cure


1.0 2.1



• Suitable for medium to large dies• Good wetting and low warpage • Recommended for thin wafer handling applications• Oven cure


1.5 1.4



• Low stress and excellent wetting for large die• Compatible with various metal surfaces, including

solder• Recommended for thin wafer handling applications• Oven cure

25L2 260°Ccapable

1.0 2.1



• Suitable for small and medium die• High adhesion• Oven cure


5.5 0.7

22 | Wafer Backside Coatings Wafer Backside Coating | 23


WA F E R B AC K S I D E COAT I N G S ( W B C ) FO R W I R E B O N D L E A D F R AM E PAC K AG I N G

Discrete



QFN and SOIC/SOP



LOCTITEABLESTIK

8008

LOCTITE®

ABLESTIK8008HT

LOCTITEABLESTIK8008MD

LOCTITEABLESTIK8006NS

LOCTITEABLESTIK

WBC 8901UV


LOCTITEABLESTIK

WBC 8901UV

Henkel’s novel Wafer Backside Coating materials allow for screen or stencil printing of the paste across the entire wafer in a single stroke, increasing throughput by eliminating the need to individually dispense dots of adhesive. After B-staging to create a film, Wafer Backside Coating provides consistent bond lines and small, controlled fillets, which are particularly effective for attaching small die in miniaturized packages and challenging structures like chip-on-lead, where the die pad is smaller than the die.

ELECTRICALLY CONDUCTIVE WAFER BACKSIDE COATINGS (WBC)


SUBSTRATE FINISH




(W/m ·K)

RECOMMENDED CURE

LOCTITEABLESTIK8008

Ag-filled, die attach wafer backside coating adhesive

• Excellent stencil printing and low surface roughness

• Void-free bondline without bleed

• Oven B-stage and snap or oven cure


1.0 x 10-4 2.260 sec. at 230°C

(snap)



• Applied by stencil printing• Void-free bondline without

bleed• Oven B-stage and snap or

oven cure


6.0 x 10-5 11.020 sec. at 170°C

(snap)

LOCTITEABLESTIK8008MD


• Applied by stencil printing• Low stress• Good substrate wetting• Oven B-stage and oven cure


5.0 x 10-4 6.010 min. ramp and


ELECTRICALLY NON-CONDUCTIVE WAFER BACKSIDE COATINGS (WBC)


SUBSTRATE FINISH


MODULUS AT 25°C (MPa)

CTE (ppm/°C) RECOMMENDED CUREBelow T

gAbove T

g

LOCTITEABLESTIK8006NS

Alumina/silica-filled, epoxy die attach wafer backside coating adhesive

• Applied by stencil or screen printing

• Consistent bondline down to 25 μm with minimal die tilt

• Oven B-stage and oven cure


4,376 33 136 2 hr. at 160°C

LOCTITEABLESTIKWBC 8901UV

Die attach wafer backside coating adhesive

• Wide process windows• 5 to 60 µm bondline control• Low viscosity before B-stage• Can be spray coated on

Dicing Before Grinding (DBG) wafers

• UV B-stage and oven cure

≤ 1 x 1 Cu, Ag or PPF L2 260°C capable 3,585 45 142

15 min. ramp and 30 min. hold at 90°C + 4 min. ramp and 45 min. hold at 120°C

S O L D E R PA S T E S FO RW I R E B O N D L E A D R AM E PAC K AG I N G

SOIC, TSOP and TSSOP

Dispensable

LOCTITE®

DA 100LOCTITEDA 101

Printable

SOLDER PASTES PACKAGE LEVEL EMI SHIELDING

24 | Solder Pastes Package Level EMI Shielding | 25

SOLDER PASTES

PRODUCT DESCRIPTION KEY ATTRIBUTES ALLOYPARTICLE SIZE DISTRIBUTION

VISCOSITY AT 25°C

REFLOW ATMOSPHERE

IPC J-STD 004B CLASSIFICATION

SHELF LIFE

Dispensable

LOCTITEDA 100

Halide-free, no-clean solder paste with Pb-free andhigh-Pb options

• Low color residues resistant to charring in reflow

• Very low voiding• Vacuum-mixed for reliable dispensing

performance• Excellent dispense and pause time

capability• Robust flux effective over a wide

range of reflow profiles

2.5S92A

Type 3, 4300,000 –

310,000at 5 rpm

Forming gas ROL012 months

up to -18°C

Printable

LOCTITEDA 101

Halide-free, no-clean solder paste with Pb-free andhigh-Pb options

• Low color residues resistant to charring in reflow

• Very low voiding• Robust flux effective over a wide

range of reflow profiles

2.5S92A95A

Type 3600,000at 5 rpm

Forming gas ROL0

6 monthsat

0°C – 10°C

Solder is frequently used as an alternative to conventional die attach paste when the application calls for high thermal and electrical performance. As leadframe-based devices such as SOICs, TSOPs and TSSOPs are often exposed to high temperatures during subsequent board assembly processing, high melt point alloys are important. Optimized rheology allows for printing or dispensing depending on process preferences and advanced flux technology is compatible with a wide range of reflow profiles to enable alloy adaptation when required.

The growth of higher-frequency communication standards, alongside the drive toward thinner profile packages, increased functionality and higher-density PCBs, has underscored the need for more effective, adaptable package-level EMI solutions. Henkel’s novel conformal coating metal inks are designed for modern packaging practices, facilitating an ultra-thin, cost-effective spray coating of highly-conductive EMI shielding material on the package exterior. Use of these LOCTITE ABLESTIK EMI solutions provides the shielding effectiveness of pure metal, while delivering an automated and scalable process with high UPH capability. Coatings as thin as 3 µm to 5 µm offer shielding for wide frequency range in formulations that have proven to be more than 80% more effective

than traditional organic-based conductive inks.

E M I S H I E L D I N G MAT E R I A L FO RW I R E B O N D L AM I N AT E

A N D L E A D F R AM E PAC K AG I N G

LOCTITEABLESTIK

EMI 8660S

LOCTITEABLESTIK

EMI 8880S

Conformal EMI Shielding

IsolatedCompartment

Substrate with Ground

Conformal Shielding MaterialExternal package-to-package shielding with outer coating layer

Component/Silicon

Appendix | 27

Board Level Shielding

CONFORMAL EMI SHIELDING MATERIAL

PRODUCT DESCRIPTION KEY ATTRIBUTESAPPLICATION

METHOD

VOLUME RESISTIVITY

(Ω∙cm)

OPTIMALCOATING

THICKNESS (µm)

ADHESION TO EMC (ASTM

D3359)

SHIELDED FREQUENCY

RANGE

LOCTITEABLESTIK EMI 8660S

Package-level, conformal EMI shielding coating

• Thinly spray-coated material provides uniform coverage on top and sidewalls of package

• Excellent adhesion to mold compound

Spray 1.5 x 10-5 3 ~ 5 5B (0% peel)500 MHz ~ 10

GHz

LOCTITEABLESTIK EMI 8880S

Package-level, conformal EMI shielding coating

• Thinly spray-coated material provides uniform coverage on top and sidewalls of package

• Excellent adhesion to mold compound• Excellent EMI performance at a wider

frequency range

Spray 7.9 x 10-4 3 ~ 5 5B (0% peel) 10 MHz ~ 10 GHz

Package Level Shielding

PACKAGE LEVEL EMI SHIELDING ENABLES SMALLER PACKAGES CURE TYPES

CURE TYPE DESCRIPTION

B-stagePartial cure until the material is in a solid state and relatively tack-free at

room temperature, but will soften and flow when heated

Oven cureStandard thermal cure in a traditional box oven, usually between 15 min. and

1 hr.

Snap cureFast thermal cure via in-line oven, with or without contact heat, usually under

2 min.

SkipCureVery fast thermal cure that can be partially cured during the wirebonding

process and fully cured during the molding process

UV cure Cure by exposure to ultraviolet light

INDEX OF TERMS

TERM DESCRIPTION

BGA Ball Grid Array

BMI Bismaleimide Resin

CBGA Ceramic Ball Grid Array

COB Chip On Board

CSP Chip Scale Package

CTE Coefficient of Thermal Expansion

DIP Dual In-line Package

EMI Electromagnetic Interference

FBGA Fine Ball Grid Array

IC Integrated Circuit

LGA Land Grid Array

MEMS Micro-Electro Mechanical Systems

MOSFET Metal-Oxide Semiconductor Field-Effect Transistor

MSL Moisture Sensitivity Level

PBGA Plastic Ball Grid Array

PGA Pin Grid Array

PPFPre-Plated Finishes consisting of layers of Ni, Pd and a Au finish

PTFE PolyTetraFluoroEthylene

QFN Quad Flat No-leads Package

QFP Quad Flat Package

RF Radio Frequency

SiP System-in-Package

SOIC Small Outline Integrated Circuit

TSOP Thin Small Outline Package

APPENDIX

SOLDER FLUX CLASSIFICATIONFLUX

INGREDIENTFLUX

ACTIVITY

HALIDE CONTENT (% BY WEIGHT)

CLASSIFICATIONFLUX

DESIGNATOR

Rosin (RO)

Low0 L0 ROL0

< 0.5 L1 ROL1

Moderate0 M0 ROM0

0.5 – 2.0 M1 ROH0

High0 H0 ROH0

> 2.0 H1 ROH1

SOLDER ALLOY PROPERTIESHENKEL CODE ALLOY

MELTING POINT (°C)

DENSITY (g/cm3)

ELECTRICAL RESISTIVITY (μΩ·m)

THERMAL CONDUCTIVITY (W/m·K)

2.5S Pb92.5/Sn05/Ag2.5 287 – 296 11.02 0.2 44

90iSC (High-Reliability) SAC387/Bi3/Sb1.5/Ni0.02 209 – 217 7.38 0.132 58

92A Sn91.5/Sb8.5 235 – 243 7.25 0.145 28

95A Sn95/Sb5 236 - 240 7.25 0.145 28

96S Sn96.5/Ag3.5 221 7.37 0.123 55

SAC0307 Sn99/0.7Cu/0.3Ag 217 – 228 7.33 0.15 64

SAC305* SAC305 or Sn96.5/Ag3.0/Cu0.5 217 7.38 0.132 58

SAC387** SAC387 or Sn95.5/Ag3.8/Cu0.7 217 7.44 0.132 60

* Formerly known as 97SC** Formerly known as 96SC

SOLDER POWDER PARTICLE SIZES POWDER

DESCRIPTIONHENKEL DESCRIPTION PARTICLE SIZE (μm)

Type 3 AGS 20 – 45

Type 4 DAP 25 – 38

Type 4.5 (4A) DAP+ 20 – 32

Type 5 KBP 10 – 25

Appendix | 27 26 | Package Level EMI Shielding

AMERICASHEADQUARTERS: UNITED STATES Henkel Corporation14000 Jamboree Road Irvine, CA 92606 USA Tel: +1.888.943.6535 Fax: +1.714.368.2265

Henkel Corporation20021 Susana Road Rancho Dominguez, CA 90221 USA Tel: +1.310.764.4600Fax: +1.310.605.2274

Henkel Corporation18930 W. 78th StreetChanhassen, MN 55317USATel: +1.952.835.2322Tel: +1.800.347.4572Fax: +1.952.835.0430

BRAZILHenkel BrazilAv. Prof. Vernon Krieble, 9106690-070 Itapevi,Sao Paulo, BrazilTel: +55.11.3205.7001Fax: +55.11.3205.7100

ASIA-PACIFICCHINA Henkel Management CenterBuilding 7, No. 99 Jiang Wan Cheng RoadShanghai 200438, ChinaTel: +86.21.2891.8000Fax: +86.21.2891.8952

ABLESTIK (Shanghai) LIMITEDNo. 332 Meigui South RoadWaiGaoQiao Free Trade Zone, Pu DongShanghai 200131, ChinaTel: +86.21.2702.5888Fax: +86.21.5048.4169

JAPANHenkel Japan Ltd.27-7, Shin Isogo-choIsogo-ku Yokohama, 235-0017JapanTel: +81.45.286.0161Email: [email protected]

KOREAHenkel Korea Co., Ltd.18th floor of tower B, BYC High City BldgGasan Digital 1-ro, Geumcheon-gu, Seoul,08506, South KoreaTel: +82.2.6150.3000Fax: +82.2.6947.5203 SINGAPORE Henkel Singapore Pte Ltd.401, Commonwealth Drive#03-01/02 Haw Par Technocentre,Singapore 149598Tel: +65.6266.0100Fax: +65.6472.8738 / +65.6266.1161

TAIWANHenkel Taiwan Ltd.10F., No.866, Zhongzheng Road, Zhonghe Dist., New Taipei City,23586, TaiwanTel: +886.2.22271988Fax: +886.2.22268699

EUROPEBELGIUMHenkel Belgium N.V. Nijverheidsstraat 7 B-2260 WesterloBelgiumTel: +32.1457.5611Fax: +32.1458.5530

UNITED KINGDOMHenkel Ltd.Adhesives Limited Technologies HouseWood Lane EndHemel HempsteadHertfordshire HP2 4RQTel: +44.1442.278000Fax: +44.1442.278071

henkel-adhesives.com/electronics

Across the Board,Around the Globe.

Except as otherwise noted, all marks used are trademarks and/or registered trademarks of Henkel and/or its affiliates in the U.S. and elsewhere. © 2020 Henkel Corporation. All rights reserved. LT-8270 (1/20) A4

Date post:	17-Jul-2020
Category:	Documents
Upload:	others
View:	12 times
Download:	0 times

MATERIALS FOR WIREBOND PACKAGING€¦ · leadframe packaging materials With more than three decades...

Documents