Matlab Communication

September 23, 2010

NIT DGP Student Branch

Simulating Communication Systems Simulating Communication Systems with MATLAB : An Introductionwith MATLAB : An Introduction

Aniruddha ChandraECE Department, NIT Durgapur, WB, India.

[email protected]

A. Chandra, ECE Deptt., NITD Simulating Communication Systems with MATLAB 2

Sep. 23, 2010Presentation OutlinePresentation Outline

Objective of the Lecture

Expected Background

Simulating Analog Communication Systems Amplitude Modulation (AM)

Simulating Digital Communication SystemsBinary Phase Shift Keying (BPSK)




Expected Background




Sep. 23, 2010Objective of the LectureObjective of the Lecture

After the Lecture … You’ll be able to

Write your own Matlab Script

Make a Analog/ Digital Communication Link

Compare your Results with Theoretical Values




Expected Background




Sep. 23, 2010Expected BackgroundExpected Background

I assume that …You understand

Basic MATLAB Operations (function, matrix)

Basics of Communication (modulation)

Performance Metrics (BER)




Expected Background




Sep. 23, 2010Analog Communication SystemsAnalog Communication Systems

Source

Channel

Destination Demodulator

Modulator


Sep. 23, 2010Simulate a SourceSimulate a Source

Source

Channel


Modulator

Produces message signal … e.g. a simple Sine wave



Generate message signal (simple sine wave)( ) ( )tfVtm mm π= 2sin

Define time instants (1000 sample points)tmin = 0; tmax = 10^(-3); step = (tmax-tmin)/1000;t = tmin:step:tmax;

Define amplitude and frequency (initial phase is zero)Vm = 1; % Amplitudefm = 2*10^3; % Frequency

Construct the Signalm = Vm*sin(2*pi*fm*t);

View the Signalplot(t,m,'r');



Complete MATLAB Script [Prog1.m]

tmin = 0; tmax = 10^(-3); step = (tmax-tmin)/1000;t = tmin:step:tmax; fm = 2*10^3; Vm = 1; m = Vm*sin(2*pi*fm*t); plot(t,m,'r');





Assignment #1 [Prog2.m], [Prog3.m]

What happens if there is an initial phase?phi_deg = 45;phi_rad = phi_deg*pi/180;m = Vm*sin(2*pi*fm*t+phi_rad);

What happens if the message is not sinusoidal?tmin = 0; tmax = 1; step = (tmax-tmin)/1000;t = tmin:step:tmax;f = 2; m = sawtooth(2*pi*f*t);plot(t,m,'r');


Sep. 23, 2010Simulate ModulationSimulate Modulation

Source

Channel


Modulator

Built-in functions are available (ammod, amdemod etc.)

WYSIWYG?? No


Sep. 23, 2010Amplitude ModulationAmplitude Modulation

Simulate with built-in functions [Prog4.m]

fs = 8000; % Sampling rate is 8000 samples per secondfc = 300; % Carrier frequency in Hzt = [0:0.1*fs]'/fs; % Sampling times for 0.1 secondm = sin(20*pi*t); % Representation of the signalv = ammod(m,fc,fs); % Modulate m to produce v

figure(1)subplot(2,1,1); plot(t,m); % Plot m on topsubplot(2,1,2); plot(t,v); % Plot v below

mr = amdemod(v,fc,fs); % Demodulate v to produce m

figure(2);subplot(2,1,1); plot(t,m); % Plot m on topsubplot(2,1,2); plot(t,mr); % Plot mr below

Source: Introduction to Communications Toolbox in MATLAB 7.6.0 (R2008) by Amit DegadaAvailable: http://amitdegada.weebly.com/download.html

http://amitdegada.weebly.com/download.html







Don’t have the feel??? …. Try this

Define message signal, (as done earlier)

tmin = 0; tmax = 10^(-3); step = (tmax-tmin)/1000;t = tmin:step:tmax;Vm = 1;fm = 2*10^3;m = Vm*sin(2*pi*fm*t);

Define carrier,

Vc = 2; % Amplitudefc = 10^4; % Frequencyc = Vc*sin(2*pi*fc*t); % Carrier signal

( ) ( )tfVtm mm π= 2sin

( ) ( )tfVtc cc π= 2sin



Continued ….

Modulate the Signal,

v = (1+m/Vc).*c; % DSB-FC modulation

View Modulated Wave

plot(t,v); % Modulated Wavehold on; plot(t,Vc*(1+m/Vc),'r:'); % Upper Envelopehold on; plot(t,-Vc*(1+m/Vc),'r:'); % Lower Envelopehold off ;

( ) ( ) ( )tftfVVVtv cm

c

mc π⎥

⎦

⎤⎢⎣

⎡π+= 2sin2sin1



Complete MATLAB Script [Prog5.m]

clear all; close all; clc;tmin = 0; tmax = 10^(-3); step = (tmax-tmin)/1000;t = tmin:step:tmax; % TimeVm = 1; Vc = 2; % Amplitude fm = 2*10^3; fc = 10^4; % Frequency

m = Vm*sin(2*pi*fm*t); % Messagec = Vc*sin(2*pi*fc*t); % Carrierv = (1+m/Vc).*c; % Modulated Wave

plot(t,v); hold on; plot(t,Vc*(1+m/Vc),'r:'); hold on; % Upper Envelopeplot(t,-Vc*(1+m/Vc),'r:'); hold off % Lower Envelope





Assignment #2 [Prog6.m]

How to view effect of changing modulation index? tmin = 0; tmax = 10^(-3); step = (tmax-tmin)/1000;t = tmin:step:tmax; Vm = 1; mu = 1.5; Vc = Vm/mu; fm = 2*10^3; fc = 10^4;

m = Vm*sin(2*pi*fm*t); c = Vc*sin(2*pi*fc*t); v = (1+m/Vc).*c;

plot(t,v); hold on; plot(t,Vc*(1+m/Vc),'r:'); hold on; plot(t,-Vc*(1+m/Vc),'r:'); hold off



Assignment #2 (Contd…) [Prog7.m]

How to simulate DSB-SC modulation?tmin = 0; tmax = 10^(-3); step = (tmax-tmin)/1000;t = tmin:step:tmax; Vm = 2; Vc = 1; fm = 2*10^3; fc = 10^4;

m = Vm*sin(2*pi*fm*t); c = Vc*sin(2*pi*fc*t); v = m.*c;

plot(t,v); hold on; plot(t,m,'r:'); hold on; plot(t,-m,'r:'); hold off


Sep. 23, 2010DemodulationDemodulation

Demodulate DSB-SC with filter [Prog8.m]

clear all; close all; clc;tmin = 0; tmax = 1; step = (tmax-tmin)/(10^3);t = tmin:step:tmax; Vm = 2; Vc = 1; fm = 2; fc = 10^2;

m = Vm*sin(2*pi*fm*t); c = Vc*sin(2*pi*fc*t); v = m.*c;

r = v.*c;

[b a] = butter(1,0.01);mr = filter(b,a,r);

figure(1)subplot(2,1,1); plot(t,m);subplot(2,1,2); plot(t,mr);





Ideal Demodulation of DSB-SC [Prog9.m]

clear all; close all; clc;fs = 10^5; N = 10^5; t = 1/fs:1/fs:N/fs; fm = 2; fc = 10^3; m = sin(2*pi*fm*t); c = sin(2*pi*fc*t); v = m.*c;

r = zeros(1,N); n =f s/fc;for k = 1:fc

mr((k-1)*n+1:k*n) = 2*v((k-1)*n+1:k*n)*c((k-1)*n+1:k*n)'/n;end

figure(1)subplot(2,1,1); plot(t,m);subplot(2,1,2); plot(t,mr);




Sep. 23, 2010Analog Communication SystemsAnalog Communication Systems

Source

Channel


Modulator

Introduces noise … Additive White Gaussian Noise


Sep. 23, 2010Simulate ChannelSimulate Channel

Introducing AWGN [Prog10.m]fs = 10^5; N = 10^5; t = 1/fs:1/fs:N/fs; fm = 2; fc = 10^3; m = sin(2*pi*fm*t); c = sin(2*pi*fc*t); v = m.*c;

SNRdB = 10; SNR = 10^(SNRdB/10);vn = var(v)/SNR;n = sqrt(vn)*randn(1,N);v = v + n;

r=zeros(1,N); n=fs/fc;for k=1:fc

mr((k-1)*n+1:k*n)=2*v((k-1)*n+1:k*n)*c((k-1)*n+1:k*n)'/n;end

figure(1)subplot(2,1,1); plot(t,m);subplot(2,1,2); plot(t,mr); axis([0 1 -1 1])


Sep. 23, 2010Simulate ChannelSimulate Channel




Expected Background




Sep. 23, 2010Digital Communication SystemsDigital Communication Systems

Source

Channel


Modulator


Sep. 23, 2010Simulate BPSKSimulate BPSK

Simulation [Prog11.m]

%This program simulates BER of BPSK in AWGN channel%clear all; close all; clc;num_bit=100000; %Signal length max_run=20; %Maximum number of iterations for a single SNREb=1; %Bit energySNRdB=0:1:9; %Signal to Noise Ratio (in dB)SNR=10.^(SNRdB/10);

hand=waitbar(0,'Please Wait....');for count=1:length(SNR) %Beginning of loop for different SNR

avgError=0;No=Eb/SNR(count); %Calculate noise power from SNR



Simulation (Contd.) [Prog11.m]for run_time=1:max_run %Beginning of loop for different runs

waitbar((((count-1)*max_run)+run_time-1)/(length(SNRdB)*max_run));Error=0;

data=randint(1,num_bit); %Generate binary data sources=2*data-1; %Baseband BPSK modulation

N=sqrt(No/2)*randn(1,num_bit); %Generate AWGN

Y=s+N; %Received Signal

for k=1:num_bit %Decision device taking hard decision and deciding errorif ((Y(k)>0 && data(k)==0)||(Y(k)<0 && data(k)==1))

Error=Error+1;end

end

Error=Error/num_bit; %Calculate error/bitavgError=avgError+Error; %Calculate error/bit for different runs

end %Termination of loop for different runs



Simulation (Contd.) [Prog11.m]BER_sim(count)=avgError/max_run; %Calculate BER for a particular SNR end %Termination of loop for different SNR BER_th=(1/2)*erfc(sqrt(SNR)); %Calculate analytical BERclose(hand);

semilogy(SNRdB,BER_th,'k'); %Plot BERhold onsemilogy(SNRdB,BER_sim,'k*');legend('Theoretical','Simulation',3);axis([min(SNRdB) max(SNRdB) 10^(-5) 1]);hold off




Sep. 23, 2010ReferencesReferences

[1] http://www.mathworks.com/matlabcentral/

[2] http://www.freewebs.com/acwebpage/teaching.htm

[3] B.P. Lathi and Z. Ding, Modern Digital and Analog Communication Systems, Oxford University Press, International 4th edition, 2010.

[4] J.G. Proakis, M. Salehi, and G. Bauch, Contemporary Communication Systems using MATLAB, Thomson/ CL-Engineering, 2nd edition, 2003.

http://www.mathworks.com/matlabcentral/

http://www.freewebs.com/acwebpage/teaching.htm


Sep. 23, 2010

Thank You!

[email protected]

Date post:	04-Oct-2014
Category:	Documents
Upload:	harini-vemu
View:	111 times
Download:	6 times

Matlab Communication

Documents