mattress not included

55-1/2” L x 31” W x 44” H

1

CONGRATULATIONS on your purchase of quality furniture by Summer®. Your nursery furniture is thoughtfully designed to fit comfortably into your lifestyle and should provide you with years of reliable service if properly assembled and maintained.

Please read these instructions completely before use of this product. Failure to follow these warnings and the assembly instructions could result in serious injury or death. Please save manual for future use as it contains important information.

Please call toll free 1. 888.443.9876, or visit www.summerinfant.comif you have any questions about your Summer ® furniture including missing parts or how to assemble.

Model #: 15210A / 15270A / 15280A

Component Assembly

B

C

Hardware List

1. Place Headboard (A) on a soft, clean surface to prevent scratching.

2. Insert 1pc Wood Dowel (5) into pre-drilled hole on top of Headboard Left Leg (B) then attachHeadboard Left Leg (B) into pre-drilled hole on Top Crown of Headboard (A). SecureHeadboard Left Leg (B) to Headboard (A) using 2pcs Bolts (4). Push the Headboard LeftLeg (B) upward to minimize the gaps on top of leg and Headboard (A). Tighten securely withAllen Key (7).

3. Repeat the same process to attach Headboard Right Leg (C) to Headboard (A).

Step 1

1. Place Side Rails (G1) & (G2) on a soft, clean surface to prevent scratching.

2. Attach Footboard Left Leg (E) to Side Rail (G1) using 2pcs Bolts (3) and 1pc Wood Dowel (5).Tighten securely with Allen Key (7).

3. Repeat the same process to attach Footboard Right Leg (F) to another Side Rail (G2).

1. Attach the assembled parts of Side Rails (G1) and (G2) to Footboard (D) using 4pcs Bolts (2).Tighten securely with Allen Key (7).

G1

1. Attach the assembled parts of Headboard to the assembled parts of Side Rails using 2pcsWood Dowels (5) and 4pcs Bolts (2). Tighten securely with Allen Key (7).

A

G1

1. Set Crib parts upright with feet on the floor.

2. Align Metal Spring Support Platform (H) with top holes on Inside Legs.

3. Insert 1pc Bolt (1) through slot of bracket and thread into hole in leg to tighten.

4. Repeat three times to attach Metal Spring Support Platform (H) to both sides of crib.

1. Disassemble crib parts so that only the assembled Headboard and the assembled Footboardare used.

2. Attach bedrails to the assembled Headboard and the assembled Footboard using 8pcs FlatWashers (6) and 8pcs Bolts (1). Tighten securely with Allen Key (7).

Optional Toddler Bed / Day Bed

1. Place Top Side Rail (J) and Lower Side Rails (K) on a soft, clean surface to preventscratching.

2. Attach 2pcs Top Side Rail (J) and 4pcs Lower Side Rails (K) to Long Rail (I) using 6pcs Bolts(2). Tighten securely with Allen Key (7).

1. Place sub-assembly on a soft, clean surface facing downwards as shown.

2. Slide Top Shelf (L) into the grooves on Top Side Rails (J) and Long Rail (I).

3. Slide Lower Shelves (M) into the grooves on Lower Side Rails (K) and Long Rail (I).

1. Insert the pre-attached wood dowels on Top Shelf Support (N) into the pre-drilled holes onLong Rail (I).

2. Attach another Long Rail (I) to the assembled parts using 6pcs Bolts (2). Tighten securely withAllen Key (7).

1. Set Changing table upright with the feet on the floor.