Your gain.
Non-water-miscible coolantsIproducts
Copper corrosion Short description
Honing oils
r.rhenus GP 5 M 4.8 1 All-purpose honing oil for the machining of steel and non-ferrous metals. Also suitable for very fine machining operations.
r.rhenus GP 6 5.5 1 Low-emission honing oil based on ester, also suitable for very fine machining operations.
Grinding oils
r.rhenus GP 4 4.8 1 Low-viscosity grinding oil, free from aromats, also for hard metal grinding.
r.rhenus Rotanor CXS
10 1 Grinding oil for the grinding of gear and profile parts with CBN grinding wheels. The product has been approved by Kapp (grinding oil e.g. for Reishauer, KAPP and Gleason machines).
r.rhenus R-OiL G 10
10 1 Low-viscosity, low-emission grinding oil, free from aromats, for high performance grinding, e.g. for crankshafts.
r.rhenus R-OiL HM 7
7.5 1 Low-viscosity and low-emission carbide grinding oil, free from aromats.
r.rhenus GP 20 M 20 1 Low-emission universal grinding oil for operations on steel, aluminium and non-ferrous metals.
Cutting oils
10 1 Low-viscosity, low-emission universal neat oil, free from aromats.
r.rhenus UP 21 M 21 1 Low-emission universal neat oil.
r.rhenus EP 10 M 10 1 Low-emission EP neat oil for steel, cast iron, non-ferrous metals and aluminium, grinding of cam shafts.
r.rhenus EA 19 S 19 4 Low-emission EP neat oil for heavy machining operations such as drilling, thread-cutting, milling and tapping.
Th e
pr od
uc ts
li st
ed h
er e
re pr
es en
t ju
st a
s el
ec tio
n fr
om o
ur p
ro du
ct r
an ge
Copper corrosion Short description
r.rhenus R-OiL DD 10
10 4 Low-viscosity, low-emission deep drilling oil, free from aromats especially suitable for drilling with single lip drills of diameters of 1 to 15 mm.
r.rhenus EP 15 S 15 1 Low-emission deep drilling oil for all current drilling operations. Multi-purpose neat oil with high performance.
r.rhenus UA 19 S 19 4 For deep drilling in BTA operations in tungsten carbides, also suitable for heavy duty machining.
Broaching oils
r.rhenus UA 28 S 28 4 Broaching, milling and deep drilling of difficult to machine materials, high performance neat oil.
r.rhenus UA 17 S 17 4 EP broaching oil for intricate and slow internal broaching on high- alloyed steels.
r.rhenus EA 25 S 25 4 EP broaching oil for intricate operations when high adhesion is required.
Thread cutting oils
r.rhenus UA 24 S 23 4 For thread-cutting and drilling on high-alloyed materials and cast steel, also suitable for broaching and shocking.
r.rhenus UA 42 S 43 4 Like r.rhenus UA 24 S, but with higher viscosity.
Spray lubricants for minimum quantity lubrication
r.rhenus Rotanor CBR
25 1 Thin-film spray lubricant for sawing of steel and aluminium.
r.rhenus Nor SSL 47 1 Spraying lubricant for machining of non-ferrous metal, steel, tungsten carbides and aluminium, usable also for tube drawing of copper and nickel tubes.
r.rhenus Nor SSU 39 3 EP spray lubricant for highest demands in machining performance (washable).
r.rhenus Nor SSC 6 1 Sawing and machining of steel, aluminium and non-ferrous metals with marginal residues.
Water-miscible coolantsIproducts
The all-purpose coolants
r.rhenus R-COOL-S 1)
41 Polar 5 X XX X XX X All-purpose coolant optimum use on machining centres. WGK 1
r.rhenus R-COOL-S niron 1)
34 Polar 5 X X X XX XX Specifically for non-ferrous metals and very sensitive aluminium alloys.
r.rhenus R-COOL-S plus 1)
29 Polar/EP 5 XX XX Specially for most difficult- to-machine high-alloy steel. WGK 1
r.rhenus FU 50 TD 1)
50 Polar 5 X X XX X Universal coolant, good long-term stability, preferable for aluminium operations.
r.rhenus FU 52 TD 1)
44 Polar 4 X XX X XX X
All-purpose coolant for plants severely contaminated with microbacteria.
r.rhenus TU 30
17 Polar 4 XX XX X X X Universal coolant with excellent cooling and rinsing effect.
r.rhenus TY 100 S
0 3 XX XX XX X X Clear abrasive, very low-foaming and almost scentless. WGK 1
r.rhenus FY 121 L 1)
0 Polar 3 X XX XX X X Clear coolant for machining and forming. WGK 1
r.rhenus TS 30
21 4 XX XX X X Grinding and light machining, low foaming and good rinsing.
r.rhenus TU 34
36 Polar 4 XX XX X XX All-purpose coolant, low foaming and good rinsing.
xx = particularly suitable x = suitable WKG 1 = German water hazard classification
1) amine-free G cast iron, grey cast iron, nodular graphite iron, malleable cast iron S steel/cast steel (not rust-proof/austenic) X rust-proof steel/cast steel with austenic structure H hardened steel or cast Z difficult-to-machine alloys with Ni, Co, Fe or Ti basis N non-ferrous materials and non-metals
Water-miscible coolantsIproducts
Th e
pr od
uc ts
li st
ed h
er e
re pr
es en
t ju
st a
s el
ec tio
n fr
om o
ur p
ro du
ct r
an ge
Material Notes on use
r.rhenus SLA 68 Viscosity 68 mm2/s as 40 °C
Rhenus slideway oils are optimally adjusted to Rhenus coolants. With a demulsifying setting they guarantee highest safety for the machine – no stick-slip – and can easily be separated from the emulsion. They achieve highest grades in the SKC test.
r.rhenus SLB 220 Viscosity 220 mm2/s as 40 °C
Service products
r.rhenus ZC 948 For all mineral-oil containing and ester-based coolants
The use of system cleaners before a fresh filling of coolant systems allows longer lifetimes and better hygiene. Therefore, the performance of the coolant can be fully utilized.r.rhenus ZC 944
For water-soluble, mineral-oil free coolant
r.rhenus ZU 900 Universal additive For elimination of reciprocal influencing inter- ferences during long-term application of cool- ants – life time extension.
r.rhenus ZW 977 Anti-foam for all mineral-oil con- taining and mineral-oil free cool- ants
Is effective in very small dosages against foam which interferes in the operation process.
The special lubricants
r.rhenus R-SEVEN 1)
39 Polar 5 Aluminium, steel
Universal coolant, optimum use on machin- ing centres and transfer lines, e.g. for com- plex aluminium operations incl. thread-cut- ting and Mapal reaming.
r.rhenus R-COOL-S micron 1)
Grinding and light machining. WGK 1
r.rhenus R-FLEX
0 Polar/EP 2/2 Difficult to machine steel, aluminium and special alloys. G, X, N, Z
The two-component coolant: r.rhenus R-Flex lub – the ester coolant r.rhenus R-Flex em – the emulsifier package Flexibly adjustable cutting performance, minimal foam development.
r.rhenus FU 60 1)
0 Polar 4 Difficult to machine steel, aluminium and special alloys.
Ester coolant for intricate machining and forming. WGK 1
r.rhenus XT 40 MG
35 Polar 5 Magnesium Special coolant for magnesium operations, minimises the hydrogen generation.
r.rhenus FS 71 1)
White emulsifying universal coolant with high mineral-oil content.
r.rhenus XY 120 HM
0 3 Hard metal Grinding product for production of hard metal tools.
Products Viscosity (40 °C) [mm2/s]
Copper corrosion Materials Short description
Evaporating punching oils
r.rhenus SE 5 2.9/20 °C 1 Steel, alumin- ium, brass, copper
Evaporating punching oil VbF A III for, for example, the manu facture of transformer plates, clips and similar punch/bend parts.
r.rhenus SE 16 2.9/20 °C 1 Steel, alumin- ium, brass, copper
Evaporating punching oil VbF A III for, for example, the manu- facture of perforated plates with thickness of up to 2 mm and punch/bend parts of comparable thickness range.
Chlorine-free fine blanking oils
r.rhenus SF 125 A 125 4 Steel such as QStE 420 C 10 etc.
Chlorine-free fine blanking oil for fine blanking of all normal steel grades suitable for fine blanking up to 8 mm (fine-grained con- structional steels, case-hardened steels / hot strip GKZ grade).
r.rhenus SF 150 A 150 4
Steel such as: 20 MnCr5; C 35; C 40; 100 Cr 6
Chlorine-free fine blanking oil specifically for high levels of severity also for less demanding steel grades and for abrasive materials (tempering steels, spring steels / hot and cold strip in GKZ grade).
r.rhenus SF 260 A 260 4 Steel such as: 20 MnCr5; C 35; 100 Cr 6
High-viscosity chlorine-free fine blanking oil specifically for difficult materials of thicknesses up to 12 mm (tempering steels, spring steels / hot and cold strip in GKZ grade).
Drawing oils
r.rhenus SW 35 P 40 1 Steel, aluminium
Mineral oil-free, water-miscible drawing oil for drawing of steel and aluminium profiles and for deep drawing of steel and aluminium. Used both neat and mixed with water for emulsions of up to 10%. Suitable for circular lubrication.
r.rhenus Rotanor SCM
Steel, aluminium, non-ferrous metals
Water-miscible drawing oil for heavy forming of all materials, e.g. for deep-drawing of motor car wheel rims of steel or aluminium. Stable emulsion up to 30%. Suitable for circular lubrication.
r.rhenus Rotanor CXI
Steel, alumin- ium, stainless steel, non- ferrous metals
Drawing oil, water-miscible for heavy forming of large-surface parts such as catalytic converter shells, etc. Used both neat and mixed with water up to 30% emulsion. Suitable only for total loss lubrication.
r.rhenus SU 125 P 120 1 Aluminium, brass and copper
Drawing oil for deep drawing and ironing of aluminium, e.g. for the manufacture of thin-wall sleeves.
r.rhenus SU 190 A 180 4 Steel, stainless steel
Drawing and punching oil for difficult forming operations such as bending of steel and stainless steel.
r.rhenus SU 120 A 125 4 Steel, stainless steel
Drawing and punching oil for raised requirements on fine and medium plate of up to 4 mm.
Special oils for metal-forming operationsIproducts
Th e
pr od
uc ts
li st
ed h
er e
re pr
es en
t ju
st a
s el
ec tio
n fr
om o
ur p
ro du
ct r
an ge
Copper corrosion Short description
Oils for tube, profile and bar drawing
r.rhenus DU 42 P 42 1 For pulling profiles and wires made from copper, bronze and aluminium. Can be applied as a spray, but also as a wash.
r.rhenus DU 2700 P
2,700 1 Is used for drawing brass and copper tubes, rods and profiles. It can also be used for drawing aluminium and nickel-silver. It is suitable for internal and external lubrication.
r.rhenus DU 700 P 700 1 For drawing of bars, profiles and tubes of non-ferrous metals. Used both for gauge plate lubrication and plug lubrication. No washing needed before annealing under glass. Product leaves no residue or discolouration.
r.rhenus DU 601 P 600 1 Suitable for the drawing of non-ferrous semi-finished products as well as for calibrating aluminium engine casings. Good residue behaviour after annealing under glass.
r.rhenus DE 12 P 12 1 Evaporating drawing oil. Used in particular for drawing of soft and semi- hard copper tubes in the last draw (plug drawing).
Products for High Pressure Forming
r.rhenus FE 80 80 4 For pre-forming, folding and outer lubrication of tubes and profiles of steel and stainless-steel for IHU-presses.
r.rhenus FSC-IHU 12 /20 °C 1 Water-soluble pressure medium for inner high pressure forming. Approved by Schuler-Hydroforming.
Products Viscosity (40 °C) [mm2/s]
Copper corrosion Materials Short description
Cold extrusion oils
r.rhenus PU 60 A 60 4 Alloyed, phos- phated or soap coated
Clear, neutral-odoured, thin-bodied cold extrusion oil for the manufacture of screws and joining elements with high deformation strain.
r.rhenus PU 115 A 120 4 Rust and acid-proofed steels
Bright extrusion oil for very difficult forming operations for the manufacture of solid, hollow and dished parts.
r.rhenus PU 135 P 135 1
Alloyed, phos- phated or soap coated steels, alumin- ium, copper and brass
Clear, mild-odoured cold extrusion oil, which is suitable for both forming and machine lubrication. Used for the manufacture of all common joining elements of up to 6 mm diameter.
Special oils for metal-forming operationsIproducts
Rhenus Lub GmbH & Co KG Erkelenzer Strasse 36 41179 Mönchengladbach Germany Phone +49 21 61 58 69-0 Fax +49 21 61 58 69-93 eMail vertrieb@rhenusweb.de www.rhenuslub.com
1. 00
0/ 08
08 G
B
Safety connects. Rhenus lubricants. Our brand with your products and services stands for a safer and economical process in metalworking operations, forming and industrial lubrication.
Lubricants by Rhenus. Worldwide. With our head office and production site in Mönchengladbach, affiliates in the whole of Europe and distributors in selected markets in Asia and South America we are always close to our customers.
Seeing the whole picture. Our way to your goal. rhenus lubrineering. Concentrating on the core business, raising quality standards and im- proving cost efficiency are the order of the day for all companies and therefore for all of our customers. The philosophy of rhenus lubrineering, therefore, stands for first-class advice and support; concerning all aspects of our products and in conjunction with ongoing cost transparency and control. To safeguard production processes and to achieve company targets.