+ All Categories
Home > Documents > MDS Monitoring Software. Page 2 Contents Introduction User Interface Service Personnel Interface ...

MDS Monitoring Software. Page 2 Contents Introduction User Interface Service Personnel Interface ...

Date post: 30-Dec-2015
Category:
Upload: mabel-peters
View: 221 times
Download: 0 times
Share this document with a friend
27
MDS Monitoring Software MDS Monitoring Software
Transcript

MDS Monitoring SoftwareMDS Monitoring Software

Page 2

Contents

Introduction User Interface Service Personnel Interface System Requirement Demonstration

Page 3

Introduction

Page 4

Introduction

Smart Commander Human to MDS system interface

- 32 Outdoors

- 48 indoors per indoors

- Total1536 indoors

Monitor and control the MDS system both indoors and outdoors

User and Service Personnel Interface

Page 5

Smart Commander Layout

Gateway

Computer

Indoor unitsOutdoor unitsCentralize Control

RS485

RS232

Introduction

Page 6

User Interface

Page 7

User Interface

Indoor Monitoring and Control Interface

Page 8

User Interface

System Monitoring and Control Interface

Page 9

Type of Control

Features

Single Control: Select a indoor unit only

Multiple Control: Select many indoor units

Group Control: All the indoor units in the system

Page 10

Area of Control

• ON/OFF

• Temperature Setting

Click “ ” or “ ”, can adjust the set temperature

Select “ ” or “ ”, can turn on or close the units

Features

Page 11

Area of Control (…continue…)

• Operating Model (Cool, Heat, Dry or Fan)

• Air Swing (Not applicable for MCC model)

• Fan Speed

• Sleep Mode

• Handset Lock Function

Select fan speed:(must select)

Select mode (must select)

Select assistant functions:

Features

Page 12

Icon for indoor/outdoor unit Basic control in “Indoor Monitor” page

Features

Page 13

Group Setting with 7 days programmable timer

Features

Page 14

Customize grouping with 7 days programmable timer

Features

Page 15

Error Code

Features

Page 16

Service Personnel Interface

Page 17

Service Personnel Interface

Page 18

Single, Master, SlaveCooling, Heating, Defrost, Stop

Display OD programOD output capacity (Include Slave)OD output capacity (Include Slave)

TTsh_outsh_out: OD superheat: OD superheat

Digital compressor output %Digital compressor output % OD Fan: Stop, Low, HighOD Fan: Stop, Low, High

HS: High Pressure (bar)HS: High Pressure (bar) LS: Low Pressure (bar)LS: Low Pressure (bar)

Heating electronic expansion valve

Subcool electronic expansion valve

Bypass way vale4-way valve (Heatpump model)

Available Data - OD

Page 19

TH1: Discharge air temp

TH2: The 1st condenser entering temp

TH3: The 1st condenser middle temp

TH4: The 2nd condenser entering temp

TH5: The 2nd condenser middle temp

TH6: Entering water temp

TH7: Heating water temp

TH8: Outdoor temp

TH9: Temp before subcool

TH10: Temp after subcool

TH11: Subcool loop exit temp

TH12: Suction temp

Sensor is Sensor is unavailableunavailable

Available Data - OD

Page 20

Outdoor AddressOutdoor Address

Red Line: HeatingRed Line: HeatingGreen Line: Cooling / DryGreen Line: Cooling / DryBlack Line: StopBlack Line: Stop

Sensor locationSensor location

Refrigerant Diagram & Sensor Location

Outdoor ModelOutdoor Model

Page 21

Indoor addressIndoor address

Indoor Control and Sensor Reading

Indoor Data:Indoor Data:Type of indoor and modelType of indoor and modelTr: Return Air TemperatureTr: Return Air TemperatureTo: Coil Outlet TemperatureTo: Coil Outlet TemperatureTm: Coil Middle TemperatureTm: Coil Middle TemperatureTi: Coil Inlet TemperatureTi: Coil Inlet TemperatureTs: Set TemperatureTs: Set TemperatureEXV: Indoor EXV OpeningEXV: Indoor EXV Opening

Page 22

Click “Up” or “Down”, Click “Up” or “Down”, ID address number will ID address number will move up or downmove up or down

Click “Back Page” Click “Back Page” or “Next or “Next Page”, the page will Page”, the page will turn up or downturn up or down

Indoor Control and Sensor Reading

Page 23

Click “Ctrl” to change indoor settingClick “Ctrl” to change indoor setting• Choose optional parameters to control Choose optional parameters to control

single unit single unit • Optional mode: Stop, Cooling, Heating, Optional mode: Stop, Cooling, Heating,

Dry, FanDry, Fan• Fan Speed: Low, Medium, High & AutoFan Speed: Low, Medium, High & Auto• Assistant function: Aux heater, Swing & Assistant function: Aux heater, Swing &

LockLock

Indoor Control and Sensor Reading

Page 24

System Requirement

Page 25

System Requirements

CPU : 800MHz and above Memory : 256MB RAM or Higher Hard Drive : 4G or higher for hard disk space OS : Windows 2000/XP Resolution : 1024 x 768 Monitor : Larger than 15 inch, & 17 inch is

recommended Serial port & USB port available

Page 26

Demonstration

Page 27

The End The End


Recommended