Mechanical Integration Tools / Attachments / Accessories / Units · 2019. 10. 16. · Page 1 of 22...

Page 1 of 22

Mechanical Integration Tools / Attachments / Accessories / Units

Annexure-I Technical Specifications

1. Solid carbide centre drill

1.1 Ground from solid carbide bar.

1.2 Spiral fluted. For material up to 62 HRC.

1.3 Standard : DIN333

1.4 Type : A

1.5 Countersink angle : 600

1.6 Coating : TiAlN

1.7 Cutting Direction : Right-hand

1.8 Shaft : Parallel shank to h6

1.9 Required Qty. : 05 nos. (Point Nominal Ø 2.5 mm)

05 nos. (Point Nominal Ø 4.0 mm)

2. Modular Vices

2.1 Simple mechanical actuation (up to 3.5 t)

2.2 Easy adjustment of jaw opening.

2.3 Machine vice with pull-down jaws.

2.4 Case- hardened HRC 60.

2.5 Parallelism : 0.02 mm

2.6 Jaw Width : 150 mm

2.7 Jaw Opening : 200 mm

2.8 Weight : 35 kg – 38 Kg

2.9 Maximum clamping force at 80 Nm : 30kN

2.10 Supplied with pull-down jaws, 1-work-piece backstop, 2-T-nuts, 1-clamping wrench, 1-cross-

bar wrench.

2.11 Required Qty. : 01 no.

3. Sets of parallels

3.1 Application: In high precision work for parallel mounting of components in machine vices or

jigs.

3.2 Precision version, extremely precise flatness and rectangularity.

3.3 Hardness : 60 HRC.

3.4 Pairing tolerance : ≤0.004 mm

3.5 Width / height tolerance : ≤0.007 mm

3.6 Number of strips : 24 pair

3.7 Length : 125mm

3.8 Content : 8x11; 8x16; 8x21; 8x26; 8x31; 8x36; 10x13;m10x18; 10x23; 10x28; 10x33; 10x38;

12x15; 12x20; 12x25; 12x30; 12x35; 12x40; 14x17; 14x22; 14x27; 14x32; 14x37; 14x42


4. Compact clamps

4.1 Body and pressure arm of hardened stainless steel, with high load capacity.

4.2 The pressure piece swings on a sprung ball and can quickly be exchanged without using any

tools.

4.3 Special nylon seal provides protection against the ingress of dirt

4.4 Component design, approx.30% smaller than comparable models.

4.5 Time saving automatic clamping and releasing.

4.6 Clamping height : 8 mm – 100 mm

4.7 Pressure arm : 94 mm

4.8 Maximum clamping force : 12kN

4.9 Maximum torque : 105 N-m

4.10 Tapped hole for socket-head screws DIN 912: M10/M12.

4.11 Required Qty. : 04 nos.

Page 2 of 22

5. Special accessories for above 4.0 , compact clamps

5.1 Clamping wrench 11 AF for Monobloc, Duo, and chain clamping tool.

Required Qty. : 02 nos.

5.2 T-slot nominal size : 18 mm for M12 T-nut


6. T-bolts (clamping bolts)

6.1 T-bolt, forged and rolled thread.

6.2 Standard design, strength class : 10.9

6.3 Standard : DIN 787

6.4 Supplied with compatible extra-thick washer and compatible tall nut

6.5 T-slot nominal size : 12mm

6.6 Thread : M12

6.7 Length : 80mm


7. Sets of assorted clamping elements for T-slot nominal size / thread M12

7.1 Consisting of various clamping elements, which are required for quick clamping of tools, jigs

or components to T-slot tables.

7.2 All parts are made of quenched and tempered steel.

7.3 Supplied with : universal serrated clamp block, Plain clamps, T-bolts, Tall nuts, Studs, Collard

washer form G, Extension nuts, Low height clamping jaws, Spring clamp holder, Tool for

clearing T-slots, Combination spanner, Anti seize compound and Wooden box.

7.4 Required Qty. : 02 sets

8. Digital callipers with absolute electronics

8.1 Absolute scale, no zeroing necessary, resulting in faster, more reliable measuring.

8.2 Low power consumption (20,000hours continuous use) battery charge indicator.

8.3 With mm/inch selection and thumb roller

8.4 Measured result is displayed in easy-to-read digital characters (height 9mm).

8.5 The AOS (Advanced Onsite Sensor) electromagnetic measurement system offers enhanced

protection against water and dust.


8.7 Measuring range : 0 mm - 150 mm

8.8 Material : Stainless steel, Inox

8.9 Jaw length : 40 mm

8.10 Scale divisions : 0.01 mm

8.11 Error limit : 0.03 mm

8.12 Depth gauge : Flat


9. Digital callipers with AOS system and data output

9.1 Absolute scale, no zeroing necessary, resulting in faster, more reliable measuring

9.2 Low power consumption (20,000hours continuous use) battery charge indicator.

9.3 Measured results is displayed in easy-to-read characters (height 9mm).

9.4 The capacitive measuring system is protected against dust and against water damage to the

measuring beam, absolute system.

9.5 Supplied with compatible battery and data cable

9.6 Measuring range : 0 mm - 300 mm

9.7 Material : Stainless steel, Inox

9.8 Jaw length : 64 mm

9.9 Error limit : 0.04 mm


Page 3 of 22

10. Precision bevel squares stainless, hardened

10.1 Very high accuracy. With two bevelled straight edges on the long blade.

10.2 Through hardened and stress-relieved. Test faces ground and lapped, other faces ground.

With sturdy stock.

10.3 Used for inspection work using the light gap principle.

10.4 Accuracy class : 00

10.5 Angular tolerance : 0.004mm

10.6 Stock length : 200 x 130

10.7 Cross section of long arm : 26 x 5mm

10.8 Cross – section of short arm : 26 x 14mm


11. Precision bevel squares stainless, hardened

11.1 Very high accuracy. With two bevelled straight edges on the long blade.

11.2 Through hardened and stress-relieved. Test faces ground and lapped, other faces ground.

With sturdy stock.

11.3 Used for inspection work using the light gap principle.

11.4 Accuracy class : 00

11.5 Angular tolerance : 0.003 mm

11.6 Stock length : 100 x 70

11.7 Cross section of long arm : 20 x 3.5mm

11.8 Cross – section of short arm : 18 x 12mm


12. Precision scale

12.1 Robust metal casing.

12.2 Simple self-explanatory user guide.

12.3 Selectable mains and battery operation

12.4 Units of weight (e.g. screw weight) can be freely programmed.

12.5 Calibration programme CAL : For accuracy adjustment

12.6 Quantity counting : Reference quantities selectable 1, 5, 10, 20 pieces display

selectable between pieces and weight.

12.7 Formulating weighing : Separate memory for weight of the tare vessel and of the

formulation ingredients (net totals)

12.8 Supplied with: Mains adapter 230 V/ 50Hz and protective hood.

12.9 Scale division : 0.01g

12.10 Reproducibility : 0.02g

12.11 Linearity : ±0.05g

12.12 Settling time : 3s

12.13 Minimum unit weight : 0.01g

12.14 Dimension of weighing plate : Φ 150mm

12.15 Net weight : 2 kg to 3 kg


13. Pliers set 4-piece

13.1 Jaws chrome-plated, handles with ergonomically optimised multi-component covering, with

non-slip surface.

13.2 High cutting and gripping performance.

13.3 Water pump pliers, manganese phosphate, polished jaws, plastic coated handles.

13.4 No. of pliers : 04

13.5 Included : Water pump pliers with stepped fine adjustment, black 250 mm ;

Combination pliers, chrome-plated, with 2-component grips 180 mm;

Diagonal side cutter chrome-plated, with grips 160 mm;

Page 4 of 22

Snipe nose pliers, straight, chrome-plated, with grips 200mm.


14. Heavy duty combination pliers ergo

14.1 Chrome vanadium steel, chrome-plated head and joint.

14.2 Slim, rounded jaws; serrated inside.

14.3 Heavy duty grips with opening spring that can be engaged/disengaged.

14.4 Cutting edges additionally induction hardened (approx. 64 HRC); also suitable for piano

wire.

14.5 Standard : DIN ISO 5746

14.6 Overall length : 180 mm

14.7 Cutting capacity hard wire up to Φ : 2.5 mm

14.8 Cutting capacity piano wire up to Φ : 2 mm


15. Heavy-duty combination pliers, offset VDE insulated

15.1 Considerable cutting performance with little effort. Serrated jaws.

15.2 Cutting edges additionally induction hardened (approx. 64 HRC), also suitable piano wire.

15.3 Insulated to DIN EN 60900/VDE 0682-201.

15.4 Offset design for improved ergonomics and a clear view of the working area.

15.5 Electrical insulation : VDE 1000 V

15.6 Standard : DIN ISO 5743

15.7 Material : special tool steel, drop-forged, and oil-hardened.


15.9 Cutting capacity hard wire up to Φ : 2.5 mm

15.10 Cutting capacity piano wire up to Φ : 2 mm


16. Automatic grip wrench, self-adjusting

16.1 Automatically sets the appropriate clamping range for the jaws, allowing easy one-hand

working.

16.2 Setting the clamping force once ensures consistent clamping pressure over the entire

clamping range.

16.3 Application: for quick and secure dripping of profiled and flat materials.

16.4 Clamping force adjustable up to 10,000 N.

16.5 Overall length : 230mm

16.6 Jaw length : 30mm

16.7 Jaw capacity : 44mm


17. Angled grip wrench

17.1 Long slim jaws, angled 70.

17.2 Serrated on the inside; at the rear of the jaws a non-serrated area for clamping hoses.

17.3 The special head shape ensures that in the clamped condition the handles do not obstruct

the working area.

17.4 Application: for clamping and gripping in restricted and inaccessible places, where it is

essential that the handles do not obstruct the working area.

17.5 Material : Jaws of high – quality steel, hardened and tempered.

17.6 Head height : 120mm

17.7 Jaw length (serrated area) : 60mm


17.9 Jaw capacity : 60mm


Page 5 of 22

18. Carbide masonry drills

18.1 Drill with hard and tough carbide inserts and brazed at high temperature.

18.2 Asymmetrical flute profile for good transport of drill dust.

18.3 Hammer and rotary bits with strong carbide cutter tip.

18.4 Application: Primarily for drilling dowel holes with hammer drills in concrete, masonry

natural and synthetic stone. Also for rotary drilling in hard and soft wood, plastic, acrylic and

ceramic. Also suitable for drilling hardened steel due to corrected cutting edge.

18.5 Drill Φ : 5mm; flute length : 50mm; overall length : 85mm; shank Φ : 5 mm

18.6 Drill Φ : 6mm; flute length : 60mm; overall length : 100mm; shank Φ: 6 mm




18.10 Drill Φ : 14mm; flute length : 90mm; overall length : 150mm; shank Φ: 10mm



18.13 Drill Φ : 20mm; flute length : 100mm; overall length : 160mm; shank Φ: 12.5 mm

18.14 Required Qty. : 05 nos. each (Total Qty: 45 nos.)

19. Torque screwdriver with setting scale

19.1 Torque screwdrivers with over-torque protection for different applications from series

production to maintenance work.

19.2 With a locking mechanism that prevents adjustment of the torque when in use.

19.3 The hexagon lock shape prevents rolling away.

19.4 Setting by using micrometer scale.

19.5 Profiled light alloy handle.

19.6 Standard : Tested to DIN EN ISO 6789.

19.7 Function : When the set torque is reached the screwdriver triggers

and signals clearly (audibly and perceptibly). It is then again immediately ready for use. The

trigger mechanism is unavailable for tightening left-handed threads.

19.8 Torque range : 100 – 500 cN-m

19.9 Torque range : 1 – 5 Nm

19.10 Torque measuring accuracy : ±3 %


19.12 Φ : 33mm


20. Universal deburrer sets in a plastic box

20.1 Supplied with : Deburrer blade S100 ; Deburrer blade S150 ; Hole deburring head HSS 900

with shank 16.5 mm ; HSS external deburring head for Φ 4-18 mm ; Mini scraper blade,

straight ; Deburrer blade S20.


21. Upright cabinet perforated panel with plain sheet metal swing doors for slings storage

21.1 Outstandingly suitable for space-saving storage of lifting tackle and slings.

21.2 Swing doors reinforced on the inside and can be locked by 2-component push handle using a

cylinder lock.

21.3 Perforated panels adjustable on a 50-mm grid.

21.4 The perforated panel s are arranged as telescopic sections, each equipped with a lock so that

only one perforated panel can ever be open at a time.

21.5 Usable area for each side of the pull-out frame is 2.1 m2

21.6 Supplied with : 3 pc. Storage trays for slings; 4 pc. Universal holders 450 ;

4 pc. Universal holder 900

21.7 Material thickness : 0.9 mm

Page 6 of 22

21.8 Door opening angle : 250 degrees

21.9 Cylinder lock : Modular barrel

21.10 Drawer runner extension : Anti-tile lock

21.11 Cabinet housing internal load capacity : 1000 kg

21.12 Height : 2000mm

21.13 Width : 1000mm

21.14 Depth : 700mm

21.15 Vertical pull-out frame load capacity : 80 kg

21.16 Weight : 240 – 250 kg


22. Garment Locker with cylinder lock

22.1 Feet of 2 mm thick aluminium sheet. Back walls with ventilation slots, doors with towel

holder and name plate. The door can easily be converted from right to left hinged.

22.2 With high quality cylinder lock in the slide handle.


22.4 Material thickness : 0.9 mm

22.5 Door opening angle : 225 degrees

22.6 Cylinder lock : Modular barrel

22.7 No. of compartments : 08 nos.

22.8 Height : 1850mm

22.9 Width : 800mm

22.10 Depth : 520mm

22.11 Weight : 75 kg to 80 kg


23. Self-tightening high-performance drill chocks with MT shank (single-piece)

23.1 Drill chuck and MT shank are a single unit.

23.2 High concentricity, optimum stability

23.3 Easy and quick change due to short design, advantageous for confined working areas.

23.4 The self-tightening effect works only for clockwise rotation.

23.5 MT Shank : 2

23.6 Clamping range : 1 – 13mm

23.7 External Dia. : 50mm


24. Morse tapper reducing drill sleeves

24.1 Through hardened, internal and external tapers ground.

24.2 MT external / internal : 4/3 and 4/2


24.4 Overall length : 140 mm and 124 mm

24.5 Required Qty. : 01 no. each (Total 02 nos.)

25. Electro Mechanical pop riveters

25.1 Cordless tool for flexible use.

25.2 LED illumination of the working area. Integral belt clip.

25.3 Supplied with Li-ion battery and charger in a plastic case, mouthpieces 2.4, 3.2, 4.0, 4.8 mm.

25.4 Output voltage : 12V

25.5 Tool stroke : 20.32mm

25.6 For pop rivets in all materials up to : 4.8mm

25.7 Setting force : 9000N

25.8 Weight with rechargeable battery : 1kg – 2 kg


Page 7 of 22

26. Workshop compressor

26.1 Corrosion-free valves, highly efficient cooling, maintenance-free transmission components,

corrosion-protected reservoir.

26.2 Minimum 10 year spare parts availability guarantee. High efficiency for low operating coasts.

26.3 Portable and wheeled workshop compressor, oil-free and water-free.

26.4 Supplied with: filter pressure regulator with manometer, quick-release connection.

26.5 Note: other workman compressors available on request.

26.6 Power consumption : 1.5 kW

26.7 Maximum pressure (air) : 11bar

26.8 Maximum suction rate : 265 I/min

26.9 Pressure vessel volume : 117 Litres

26.10 Weight : 28 kg – 30 kg

26.11 Length : 400 mm – 500 mm

26.12 Width : 500 mm – 600 mm

26.13 Height : 1000 mm – 1100 mm

26.14 AC supply voltage : 240V


27. ESD proof safety protection

27.1 ESD outer sole

27.2 Aluminium protective toecap

27.3 All-round safety shoe with resilient heel.

27.4 Breathable functional lining.

27.5 Safety reflectors.

27.6 Real leather inner sole.

27.7 ERGO and SOFT, ESD comfort mid-sole inlay.

27.8 Protection against electrostatic discharge (ESD).

27.9 Sandals with hook and loop fastening. Uppers of open-cell functional textile. TPU Dynamics

ESD sole tread, white.

27.10 Standard : EN ISO 20345:2011 S1 SRC

27.11 Size : EU 41, 42, 44

27.12 Required Qty. : 04 nos. each (Total Qty. 12 nos.)

28. Leather work gloves

28.1 High-quality nappa palm leather gloves for use with mechanical risks.

28.2 With strong double seam and rubberised cuff.

28.3 Complete inner lining of light cotton fabric for more wearing comfort.

28.4 Glove size : 11

28.5 Material : Full-grain leather

28.6 Standard : EN 388:2016

28.7 Colour : blue / white


29. Banded earplugs

29.1 Headband earplugs are characterised particularly by ease of use and comfortable positioning.

29.2 This means they are particularly suitable for intermittent noise situations where they must

be frequently put on and taken off.

29.3 When not in use the headband earplugs can be worn under the chin or round the neck as

required.

29.4 Spare earplugs are available for all models.

29.5 With conical ear plugs.

29.6 Noise attenuation (SNR value) : 26 dB(A)


Page 8 of 22

30. Spare Earplugs compatible with above banded earplug

30.1 The conical earplugs are suitable for all sizes of auditory canal and can easily be exchanged

using the practical handle.

30.2 SNR value (noise attenuation) : 26 dB(A)

30.3 Each set contains pair : 25 nos.


31. Dividers for mobile workbenches

31.1 Small parts storage bin, made of plastic.

31.2 With 2 fixed dividers, for 4 compartments in the box.

31.3 Height : 25 mm

31.4 Width : 100 mm

31.5 Depth : 100 mm

31.6 Colour : anthracite


32. Coiled ¼ inch nylon hose with coupling

32.1 Usable hose length : 7.5 m

32.2 Hose external Ø : 8mm

32.3 Hose internal Ø : 6mm

32.4 Hose Ø 8 x 6 mm; nylon, giving extremely high retracting force and low pressure losses.

32.5 Supplied with 1 each quick-release coupling G1/4 inch internal thread and ¼ inch male

coupling.


33. Compressed air guns and Extension tube, compatible with above workshop compressor

33.1 Universally applicable, up to 10 bar operating pressure

33.2 With 1.5 mm standard nozzle.

33.3 Flow rate at 6bar : 250 l/min

33.4 Extension tube length : 300 mm

33.5 Supplied with: threaded coupling adapter size ¼”, hose adapter 9mm.

33.6 Required Qty. : 04 nos. each (Total: 08 nos.)

34. Spring loaded cable ring

34.1 Cable reel with guided automatic draw-in and roll-up, with multiple stop points per

revolution.

34.2 High-impact enclosed plastic housing.

34.3 Thermal overload cut-out, sturdy H07RN-F neoprene cable with connection point.

34.4 Easy to mount on the wall or ceiling with 150° pivoting range.

34.5 Application: Improved ergonomics by relieving cable tension, and for ensuring tidiness and

avoiding the risk of accidents and injuries due to cables lying on the ground.

34.6 08 1197 – cable reel 400V/ 16A : 20N

34.7 Rated power unrolled : 3000 W (16 A)

34.8 Length : 350 mm – 400 mm

34.9 Width : 200 mm – 250 mm

34.10 Height : 400 mm – 450 mm

34.11 Cable class : H07RN-F

34.12 Cable structure : 5G1.5

34.13 Material cable : neoprene

34.14 Cable length : 20m


35. Hand taps

35.1 HSS one-pass hand tap for through holes.

Page 9 of 22

35.2 Class : 6H

35.3 Required Sizes : M2, M2.5, M3, M4, M5, M6 and M8


36. Insertion spindle

36.1 Insertion tool for wire thread inserts.

36.2 Required Sizes : M2, M2.5, M3, M4, M5, M6 and M8


37. Rust remover spray

37.1 This rust remover penetrates into the smallest gaps in a flash; the powerful penetrating

capillary action loosens bolts and mechanisms.

37.2 Further improved sliding properties, avoiding recurrence of seizing through the action of the

MoS2 additive.


38. Manual Dispenser

38.1 Manual dispenser for precise application and processing of adhesive tape and Automatic

removal of the protective paper.

38.2 Suitable for adhesive film without backing : Width 19 mm x Length 33 m


39. Double-sided adhesive tapes

39.1 Double sided high performance adhesive tape of pure acrylate adhesive (VHB) for

permanently strong bonds.

39.2 High instant tack, high resistance to temperature, weather, UV and solvents.

39.3 Excellent sealing function, vibration-damping.

39.4 For metals, high temperatures and prior to powder-coating.

39.5 Length : 3m

39.6 Width : 19mm

39.7 Colour : grey

39.8 Short-term temperature-resistant to : 230 °C

39.9 Long-term temperature – resistant to : 150 °C


40. Double-sided adhesive tapes

40.1 Double sided high performance adhesive tape of pure acrylate adhesive (VHB) for

permanently strong bonds.

40.2 High instant tack, high resistance to temperature, weather, UV and solvents.

40.3 Excellent sealing function, vibration-damping.

40.4 Ideal for transparent joints and materials such as glass

40.5 Length : 11mm

40.6 Width : 19mm

40.7 Colour : transparent

40.8 Short-term temperature-resistant to : 150 °C

40.9 Long-term temperature-resistant to : 90 °C


41. Aluminium adhesive tapes

41.1 Soft pure aluminium adhesive tape with transparent acrylate adhesive.

41.2 Easy to unroll thanks to special surface coating.

41.3 Resistant to ageing and chemicals, low flammability.

41.4 Temperature-resistant from – 55 °C to + 155 °C.

Page 10 of 22

41.5 For masking, sealing, for reflecting heat and light and for providing moisture barriers.

Outstandingly suitable for long life application under very high stresses.

41.6 Length : 55 m

41.7 Width : 50 m


42. Professional manual dispenser

42.1 Robust and professional manual dispenser with manually adjustable roller braking.

42.2 Covered knife (protects against injury) and soft rubber ergonomic handle.

42.3 Application: For dispensing adhesive tapes.

42.4 Maximum width of the adhesive tape : 50mm

42.5 Maximum roll Ø of the adhesive tape : 140mm


43. Section – pad lifter

43.1 Suction lifter of sturdy aluminium, with rubber vacuum cups for a long working life.

43.2 With proven toggle lever technology.

43.3 Application: for lifting materials with smooth, grease-free and air-tight surface finishes.

43.4 Suction head Ø : 120mm

43.5 Maximum load capacity : 100 kg


44. Chain hooks

44.1 Chain hooks with quality stamp.

44.2 High – strength chain hooks with fork-head hooks GS.

44.3 Usable length : 4 m

44.4 Chain Ø : 13mm

44.5 Safe working load WLL β = 0° - 45° : 11200kg

44.6 Safe working load WLL β = 45° - 60° : 8000kg


45. Hexagon key L- wrench sets long, with ball point

45.1 L-form shaft; ball point can be applied up to an angle of 30°

45.2 Maximum hardness with special toughness due to special alloy.

45.3 Chrome-plated, ends chamfered.

45.4 Hexagon key L-wrench, long chrome-plated : 1.5 mm

Stock length : 82x16 mm


45.5 Hexagon key L-wrench, long chrome-plated : 2 mm



45.6 Hexagon key L-wrench, long chrome-plated : 2.5 mm












45.10 Total Qty. of above all sizes : 285 nos.

Page 11 of 22

46. Hexagon key L- wrenches in inch sizes

46.1 Maximum hardness with special toughness due to special alloy. Chrome-plated (size 1/20

burnished), edges slightly bevelled.

46.2 Hexagon key L-wrench, long chrome-plated : 3/32 inch

Stock length : 99 x 19 mm


46.3 Hexagon key L-wrench, long chrome-plated : 7/64 inch

Stock length : 108 x 21 mm


46.4 Total required qty. : 100 nos.

47. Hexagon sockets, ¼”, long

47.1 Forged from high quality steel, internally bevelled for easy fitting to bolt heads. Square drive

socket with bore to DIN 3120-D 6.3

47.2 Optimum grain orientation due to special forging process. Close tolerance width across flats.

No rounding of bolt corners, nuts and bolt heads are protected. Hardened in an oil bath,

stress-relieved and distortion-free for a precision fit. Rounded surface with AS drive profile.

47.3 Standard : DIN 3124-L

47.4 Material : High performance steel, non-flaking chrome plated over nickel.

47.5 Hexagon socket ¼” long

47.6 Width across flats : 6 mm

47.7 Ø drive output end : 9.2 mm

47.8 Length : 50 mm


48. Open – ended / ratchet ring spanners

48.1 Drop forged. Ring end with smooth – running sturdy precision ring ratchet (80 teeth) with a

particularly small working arc of 4.5°.

48.2 The open end has a bi-hexagon profile and a replaceable hardened metal plate, which fulfils a

stop function, preventing slippage and allowing a small working arc.

48.3 Ring end 15° offset, reversible.

48.4 Handy stop function for secure engagement on nuts and bolts.

48.5 The end stop prevents irritating slipping from the bolt head.

48.6 Small working arc, no need to turn the spanner over due to the bi-hex profile.

48.7 Material : Chrome molybdenum steel, matt chrome-plated.

48.8 Number of keys : 04

48.9 Set Content : One each spanner size 10;13;17;19

48.10 Required Qty. : 05 nos. set

49. Socket sets ¼”, large

49.1 Socket set with long sockets and bits ¼” square drive

49.2 Set content : 35 pieces

49.3 Hexagon sockets, long : Size 4; 4.5; 5; 5.5; 6; 7; 8; 9; 10; 11; 12; 13

49.4 Socket single hexagon : Size 4; 4.5; 5; 5.5; 6; 7; 8; 9; 10; 11; 12; 13

49.5 Hexagon screwdriver bits : Size 2.5; 3; 4; 5; 6; 8

49.6 T-handle : 1 pc.

49.7 Spinner handle : 1 pc.

49.8 Extension : 1 pc.

49.9 Universal joint : 1 pc.

49.10 Ratchet : 1 pc.

49.11 Presented in : Sheet metal case.

49.12 Required Qty. :10 nos. set

Page 12 of 22

50. Safety knives with 1 blade

50.1 Safety knife with 21mm depth of cut and fully automatic blade retraction. Ergonomic pliers

grip of aluminium (incl. soft-grip for optimum grip), with an easy – action lever to release the

blade.

50.2 Application: Ideal for cardboard up to 3 layers, goods on rolls, rubber, PVC, carpeting and

much more.

50.3 Length : 154 mm


51. Engineer’s level

51.1 Sturdy housing of high quality special casting; vee base with ground contact surface in the

angle (important for marking out, aligning, etc.)

51.2 All measuring faces are exactly parallel to the axis of the vial.

51.3 One longitudinal and one transverse vial each of glass.

51.4 With insulated handles on the housing and protective glass over the vials.

51.5 Adjustable of the longitudinal vial: an adjustment screw allows the longitudinal vial to be

reset to the 0 position easily and without play, with no need for disassembly.

51.6 Standard : DIN 877 – class 1a

51.7 Accuracy : 1 = DIN 877 class 1a

With very high sensitivity longitudinal vial 0.02 mm/m

51.8 Application: For aligning surfaces, shafts, machines etc.

51.9 Base length x Accuracy : 200/1 mm

51.10 Scale divisions : 0.02 mm

51.11 Sole width : 40 mm

51.12 Required qty. : 01 no.

52. Electronics screw drivers for hexagon socket head screw

52.1 Ergonomically configured multi-component handle with smooth-running rotating cap (for

fingertip pressure during precision work.).

52.2 Optimally shaped quick turning zone for fast, efficient screw driving and power zone for

transferring higher torques.

52.3 Blades of high-quality tool steel, surface matt chrome –plated black tip. Hex-plus profile

prevents deformation of the screw head and transmits more torque.

52.4 Application: For precise, efficient screw driving operations for electronics applications. Also

ideal for all sensitive setting and adjustment work.

52.5 Blade length : 60 mm


52.7 Hexagon Sizes : 2 mm ; 2.5 mm ; 3 mm

52.8 Required qty. : 10 nos. each (Total: 30 nos.)

53. Acrylic vials

53.1 Sturdy plastic body with 3 fastening holes. Round vial with ring markings for horizontal

alignment in two axes.

53.2 Diameter Ø : 30 mm

53.3 Height : 11 mm


54. Tool cases with pockets

54.1 Tool caddy of innovative high-tech material and ABS. Made of an extremely tough and light

plastic fabric with the performance characteristics of fibre-reinforced composite materials.

54.2 Tool case with a magnetic catch for easy operation, and shoulder strap. Transparent

securing pocket in the cover. Front, back and centre boards with 17 shaft pockets.

54.3 Application: Extremely sturdy and impact resistant tool cases with very low weight, ideal for

use in all maintenance, customer service and installation work.

Page 13 of 22

54.4 Internal dimension length : 200 – 250 mm

54.5 Internal dimension width : 100 – 150 mm

54.6 Internal dimension height : 300 – 350 mm

54.7 Weight : 1 – 1.5 kg


55. Assembly screwdriver set with voltage tester

55.1 Power grip with easy-to-hold, secure grip surface and a particularly tough impact resistant

polypropylene core.

55.2 Due to its special surface structure, the grip non-slip even with oily or wet hands.

55.3 Chrome-plated blades of chrome vanadium special alloy combine

55.4 Maximum hardness and exceptional toughness.

55.5 Black tips, accurately dimensioned.

55.6 Voltage tester 110 – 250 V to VDE 0680/6.

55.7 Supplied with: textile roll-up wallet.

55.8 Slot – head blade sizes : 4; 5.5; 6.5; 8

55.9 Philips blade sizes : 1 and 2

55.10 Pozidriv blade size : 2

55.11 Torx blade sizes : TX10; TX15; TX20; TX25

55.12 Reamer blade : 1 pc.

55.13 Voltage tester size : 2.5

55.14 2 – Component plastic handle : 1 PC.

55.15 Required Qty. : 05 nos. set

56. Flexible assembly gloves

56.1 Breathable assembly glove with innovative, water-based PU-nitrile coating for the highest

level of precision, flexibility and dexterity in dry and slightly oily working environments.

56.2 Particularly finely structured surface due to intensive finishing process. Long life through very

high abrasion resistance. DMF-free.

56.3 Additional raised nitrile dots for improved security of grip

56.4 Backing material : Lycra, polyamide

56.5 Coating : PU, nitrile foam

56.6 Application range : Precision

56.7 Colour : Black/Grey

56.8 Glove size : 8 and 10

56.9 Required Qty. : 03 nos. of each Pair (Total Pair: 06 nos.)

57. Scriber with replaceable points

57.1 Hollow steel shaft (5mm) with clutch and plastic covering.

57.2 Points hardened and replaceable.

57.3 Supplied with: 12 spare points stored in the shank.



58. Scribers

58.1 One Straight and one angle point, chrome-plated, point hardness 59 HRC, nylon handle.

58.2 Suitable even for high-tensile steel/materials.



59. Induction hand-held magnifying glass

59.1 Hand-held illuminated magnifying glass with innovative induction charging for

continuous and sustained charging when in continuous use.

59.2 Charging time approx. 3 hours, working time approx. 7 hours

Page 14 of 22

59.3 Scratch resistant silica glass lens with very large depth of focus and distortion-free image.

59.4 Sharp contrast and homogeneous light thanks to dual-stage adjustment of the light intensity.

Pleasant haptics thanks to ergonomic design with soft touch gripping zone.

59.5 Long-life SMD-LEDs with light Colour 4500K (neutral white).

59.6 Aplanatic silica glass lens

59.7 Supplied with induction charging pad, power supply unit, micro-fibre bag for storage and

cleaning.

59.8 Magnification (x-times) : 15

59.9 Lens Ø : 16.3mm

59.10 Colour temperature : 4500K

59.11 Required qty. : 03 nos.

60. Pin punch set with guide sleeves

60.1 Pin punch set with guide sleeve in a metal case

60.2 No. of pin punches : 09

60.3 Content : 0.9; 1.4; 1.8; 2.4; 2.8; 3.4; 3.9; 4.9; 5.9 mm

60.4 Required qty. : 05 nos. set

61. Easy pocket illuminating magnifying glasses

61.1 The illuminating magnifying glass has an aspherical diffracting lens and a CMD-LED.

61.2 The light comes on when the magnifying glass is pulled out of the glass fiber-reinforced

plastic case.

61.3 Compact credit card format.

61.4 Lens length : 50 mm

61.5 Lens width : 45 mm

61.6 Lens height : 3 mm

61.7 Magnification (x-times) : 4

61.8 Required qty. : 02 nos.

62. Cordless hammer drill / driver

62.1 Powerful cordless 2-speed hammer drill/screwdriver with multi-stage torque setting.

62.2 With overload protection for long working life of the battery, motor, and gearbox.

62.3 Red Li-ion batteries with single-cell monitoring and charge display.

62.4 Sturdy metal gearbox for long working life.

62.5 Metal quick-change chuck with spindle lock.

62.6 Handle with soft-grip coating for comfortable use.

62.7 LED illumination of the working area.

62.8 Brushless motor for very high efficiency. Very low wear and up to 10 times the working life

of standard DC motors.

62.9 Compact cordless hammer drill/driver with only 168 mm tool length. 16-stage electronic

torque adjustment plus drill step plus hammer drill mode.

62.10 Supplied with 2× 12 V / 6.0 Ah Red Li-ion batteries, C12 C charger, HD box

62.11 Battery voltage : 12V

62.12 Battery capacity : 6A-h

62.13 Maximum speed 1st speed : 0-450 rpm

62.14 Maximum speed 2nd speed : 1700 rpm


62.16 Quick clamping chuck range : 1.5 – 13 mm

62.17 Maximum twist drill size Ø in steel : 13 mm

62.18 Maximum twist drill size Ø in wood : 35 mm

62.19 Maximum twist drill size Ø in concrete : 13 mm

62.20 Weight : 1.3 – 1.8 kg

62.21 Maximum vibration to EN with hammer drill function : 30.8 m/s2

62.22 Maximum vibration to EN without hammer drill function : <2.5 m/s2

Page 15 of 22


63. Transport chassis elements

63.1 Three point heavy load chassis elements for transporting medium-weight loads.

63.2 With a towbar and a rear chassis element.

63.3 The two identical rear chassis elements have adjustment connecting roads.

63.4 Overall load capacity is distributed 50:50 between the front and rear chassis elements.

63.5 Supplied with: three chassis elements, two connecting bars, one towbar.

63.6 Safe working load : 12 t

63.7 Front loading area height : 115 mm

63.8 Front loading area length : 400 mm

63.9 Width front loading area : 220 mm

63.10 Rear adjustment range from – to : 500 – 1400 mm

63.11 Weight : 80kg


64. Professional clogs

64.1 Upper material of microfiber.

64.2 Adjustable fixed heel straps.

64.3 Exchangeable Air Comfort insole.

64.4 TPU outer sole, non-slip.

64.5 Satisfy HACCP.

64.6 Standard : Certified to EN ISO 20347:2012 OB A E FO SRC;

ATEX in accordance with EN 61340-4-3, climatic class1

64.7 Size : EU : - 41, 42, 44


65. Fabric scissors

65.1 Fabric shears with micro toothing and ergonomic 2-component handles.

65.2 Blades of stainless steel.

65.3 Application: glass fibre, aramids, and many more


65.5 Length blade : 85


66. Precision shears

66.1 Made of quenched and tempered steel. Comfortable plastic handles with opening spring.

66.2 Application: for clean, precise cutting of a very wide range of materials and fibers.

66.3 Cuts soft metal up to 0.12mm thickness.


66.5 Length cutter : 14.5mm


67. Fastener Storage system

67.1 Doors reinforced on the inside and can be locked by 2 – component push handle using a

cylinder lock.

67.2 Transparent boxes of ABS plastic for dust-free storage.

67.3 Tilt the transparent box to remove stored goods.

67.4 Bins can be removed and stacked for assembly purposes.

67.5 Colour: Body - RAL 7035 light grey and Doors - RAL 7016 anthracite power-coated.

67.6 Supplied with: cabinet with transparent boxes.

67.7 Storage cabinet with viewing window swing doors

67.8 Height : 2000mm

67.9 Width : 750mm

Page 16 of 22

67.10 Depth : 275mm

67.11 Weight : 70 – 72 kg

67.12 Components – number of transparent boxes: 36pcs.

67.13 Height : 46mm

67.14 Width : 50mm

67.15 Depth : 42mm

67.16 No. of transparent boxes: 36pcs. of 50x42x46 mm

36pcs. of 80x63x70 mm

25pcs. of 100x97x108 mm


68. Lubricant sprays

68.1 Non-greasy smooth and dry lubricant with excellent anti-adhesion properties due to the

formation of a PTFE coating. Free of oil and silicone.

68.2 PTFE dry lubricant, dry lube : 500ml spray


69. Deflecting torque wrenches with scale automatic triggering

69.1 One – arm torque wrench, adjustable by a scale, self-triggering.

69.2 The trigger mechanism makes unintentional overtightening extremely unlikely.

69.3 Anti-clockwise tightening by reversing the plug-in head.

69.4 Standard : Tested to DIN EN ISO 6789.

69.5 Accuracy : ±4% of the set value.

69.6 Function: on reaching the present torque value the wrench triggers a clearly detectable

deflection and is then immediately ready for use again. The long-travel indication gives the

user an unmistakable signal that the set torque has been reached.


69.8 Overall length L : 345mm

69.9 Torque range : 5-25 N-m

69.10 Scale graduation, 1 graduation : 0.1N-m

69.11 Weight : 1000g - 1200g

69.12 Square drive : 1/4 inch


70. Increaser piece / reducer piece

70.1 External and internal square drives to DIN 3120.

70.2 Forged external square drives with spring-mounted balls or pins.

70.3 Internal square drives with hole or snap grooves.

70.4 Standard : DIN 3123-A

70.5 Material : Chrome alloy steel, non-flaking, chrome-plated over nickel.

70.6 Internal drive square : 3/8 inch

70.7 External drive square : 1/4 inch


71. Increaser piece / reducer piece

71.1 External and internal square drives to DIN 3120.

71.2 Forged external square drives with spring-mounted balls or pins.

71.3 Internal square drives with hole or snap grooves.

71.4 Standard : DIN 3123-A

71.5 Material : Chrome alloy steel, non-flaking, chrome-plated over nickel.

71.6 Internal drive square : 1/2 inch

71.7 External drive square : 3/8 inch


Page 17 of 22

72. Straight die grinder

72.1 Powerful 18V /5.0 Ah cordless straight die grinder with brushless power state motor.

72.2 Electronics with digital overload protection for better performance.

72.3 Lithium – ion battery with single cell monitoring.

72.4 Universal arbour for all the usual 6 and 8 mm accessories.

72.5 Very slim design for increased user comfort.

72.6 Exchangeable dust-protection grille protects the motor and prolongs its working life.

72.7 Spindle neck with rubber face for extra user comfort.

72.8 Restart inhibit.

72.9 Supplied with: 2 X 18V / 0.5 Ah red Li-ion batteries; charger; 6mm collet; 8 mm collet; open

ended spanners AF 15 / 17 AF ; 2 x dust protection grilles, HD box.

72.10 Straight die grinder cordless

72.11 Battery voltage :18V

72.12 Battery capacity : 5 A-h

72.13 Maximum collet : 6-8mm

72.14 Weight : 2 – 2.5 kg

72.15 Maximum vibration to EN : 3.4m/s2

72.16 Required Qty. : 01no.

73. Extensions for taps and hand reamers

73.1 Hardened and nickel-plated. Square drive and square socket the same size.

73.2 Application: For extending short taps (e.g. DIN 351 / 352 / 2181 / 5157), hand reamers and

other tools with square shanks.

73.3 Internal and External Square size : 2.1 mm

For metric taps : M1 to M2.6

Maximum Ø : 6 mm

Overall length : 60 mm


For metric taps : M3

Maximum Ø : 7 mm



For metric taps : M4

Maximum Ø : 8 mm



For metric taps : M4.5 – M8

Maximum Ø : 11 mm



74. Tap extract set

74.1 Number of drilling-out tools : 05

74.2 Solid carbide drilling-out tool set in cartridge

74.3 One each carbide drilling-out tool sizes : M3; M4; M5; M6; M8

74.4 Required Qty. : 03 nos. of set

75. Countersink 120°

75.1 Easy and chatter-free deburring and countersinking.

75.2 Flutes ground from solid.

75.3 External Ø : 8 mm

Number of cutting edges Z : 3

Smallest countersink for holes from : 2 mm

Total Length L : 49 mm

Page 18 of 22

Feed F : 0.09 mm/rev.

75.4 External Ø : 12.5 mm


Smallest countersink for holes from : 2.8 mm



75.5 External Ø :16 mm





75.6 External Ø : 20 mm






Annexure- II Terms and Conditions

1. The quoted prices should have consideration of all the aspects, Basic Technical Specifications,

Scope of Supply and Salient Features, as mentioned in Annexure-I.

2. Quotation should be along with the detailed technical catalogue of the units and write up, highlighting

special features, specific applications, safety provisions, attachments etc.

3. Delivery period for the machine should be less than 10 weeks.

4. Order may be split among eligible vendors.

5. Quoted prices should also have consideration and inclusion of the following:

All electrical and electronic cables, mechanical fittings and other safety provisions if any.

Testing & Calibration Certification.

6. Offered products shall be compatible for working in Indian electrical supply conditions, whenever

applicable.

7. 12 months warranty for trouble free operation of the supplied products from the date of receipt

and free services will be provided for any trouble during the first year of operations. During the

period of warranty, if any part is to be replaced, supplier may replace it free of cost.

8. The Bidder shall demonstrate all type of operations / performance /specifications, after supply of

the above all products, at SAC Ahmedabad. This should include the Demonstration of all parameters,

including periodic preventive maintenance practice.

9. The Supplier should recommend and quote separately, if required, for any accessories or

attachments they find suitable, other than mentioned under, that are essential for smooth

functioning, accurate and reliable performance of the quoted items.

10. Bidder should quote bundled price for each of the different 75 items. For example, for sr. no. 75,

single price should be quoted for total 20 nos., instead of four different prices for four varieties.

11. Bidder shall provide Compliance Statement, Annexure-II, with sign and seal on all pages of tender

document, confirming that offered products, shall comply all the indent specifications. This is

mandatory requirement.

Page 19 of 22

Annexure- III Compliance Statement

(To be Filled and submitted by Bidder/Supplier while quoting tender inquiry)

Sr.

No. Description

Comply /

Not Comply Remarks

1 Solid carbide centre drill,

Annexure-I, Para 1.1 to 1.9

2 Modular Vices


3 Sets of parallels


4 Compact clamps


5 Special accessories for above 4.0, compact clamps


6 T-bolts (clamping bolts)


7 Sets of assorted clamping elements for T-slot nominal size / thread M12


8 Digital callipers with absolute electronics


9 Digital callipers with AOS system and data output


10 Precision bevel squares stainless, hardened


11 Precision bevel squares stainless, hardened


12 Precision scale


13 Pliers set 4-piece


14 Heavy duty combination pliers ergo


15 Heavy-duty combination pliers, offset VDE insulated


16 Automatic grip wrench, self-adjusting


17 Angled grip wrench


18 Carbide masonry drills


19 Torque screwdriver with setting scale


20 Universal deburrer sets in a plastic box


21

Upright cabinet perforated panel with plain sheet metal swing doors for

slings storage


Page 20 of 22

22 Garment Locker with cylinder lock


23 Self-tightening high-performance drill chocks with MT shank (single-piece)


24 Morse tapper reducing drill sleeves


25 Electro Mechanical pop riveters


26 Workshop compressor


27 ESD proof safety protection


28 Leather work gloves


29 Banded earplugs


30 Spare Earplugs compatible with above banded earplug


31 Dividers for mobile workbenches


32 Coiled ¼ inch nylon hose with coupling


33

Compressed air guns and Extension tube, compatible with above workshop

compressor


34 Spring loaded cable ring


35 Hand taps


36 Insertion spindle


37 Rust remover spray


38 Manual Dispenser


39 Double-sided adhesive tapes


40 Double-sided adhesive tapes


41 Aluminium adhesive tapes


42 Professional manual dispenser


43 Section – pad lifter


44 Chain hooks


Page 21 of 22

45 Hexagon key L- wrench sets long, with ball point


46 Hexagon key L- wrenches in inch sizes


47 Hexagon sockets, ¼”, long


48 Open – ended / ratchet ring spanners


49 Socket sets ¼”, large


50 Safety knives with 1 blade


51 Engineer’s level


52 Electronics screw drivers for hexagon socket head screw


53 Acrylic vials


54 Tool cases with pockets


55 Assembly screwdriver set with voltage tester


56 Flexible assembly gloves


57 Scriber with replaceable points


58 Scribers


59 Induction hand-held magnifying glass


60 Pin punch set with guide sleeves


61 Easy pocket illuminating magnifying glasses


62 Cordless hammer drill / driver


63 Transport chassis elements


64 Professional clogs


65 Fabric scissors


66 Precision shears


67 Fastener Storage system


68 Lubricant sprays


Page 22 of 22

69 Deflecting torque wrenches with scale automatic triggering


70 Increaser piece / reducer piece


71 Increaser piece / reducer piece


72 Straight die grinder


73 Extensions for taps and hand reamers


74 Tap extract set


75 Countersink 120°


76 Terms and Conditions

Annexure-II, Para 1 to 11

__________________

Sign and Seal of Bidder (on all pages of Tender Documents)

Date post:	03-Sep-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times