Date post: | 28-Jul-2015 |
Category: |
Engineering |
Upload: | mohammed-enab |
View: | 588 times |
Download: | 12 times |
Shaft Seals
Description-:Centrifugal and rotary positive displacement pumps require controlling of the pumped fluids desire to exit through the stuffing box, the area where the pump shaft enters the pump fluid end. When operating the pumped fluid within The stuffing box sees a pressure higher than the surrounding atmospheric pressure, the fluid coming from this side (stuffing box ), So we
need shaft seal to prevent the leakage or reduce it.
ال حتى المضخة السائل كمية فى التحكم يتطلب المضخات استعمال حالة فىمن )) stuffing boxتتسرب
اعلى يكون المعدة دخل الضغط أن الجوى ) ( حيث الضغط الخارجى الضغط منالمنطقة تلك فى تسريب مانع لعمل نحتاج لذلك خاللها من تهريب يحدث لذلك
نهائيا . منعه او التسريب لتقليل
Purpose of use shaft seals
To prevent leakageالتسريب لمنع
To reduce vibrationاالهتزازات لتقليل
To reduce rotating friction and corrosion of the pump shaft
التاكل وتقليل الدورانى االحتكاك لتقليل
Type of shaft seals
1) - Packing ring.2) - Mechanical Seal.1.A)-Packing ring (for Centrifugal pump)1.1)-Stuffing box.The stuffing box is a chamber or a housing that serves to seal the shaft where it passesthrough the pump casing.
1.2 -)How to reduce leakage .In a stuffing box, suitable packing rings are placed and a gland (end plate) for tighteningand pressing them down the shaft.The narrow passage, between the shaft and the packing housed in the stuffing boxProvides a restrictive path to the liquid, which is at a high pressure within the pumpcasing. The restrictive path causes a pressure drop, prevents leakage resulting inConsiderable friction between the shaft and the packing, and causes the former toHeat Up , It is thus good practice to tighten the gland just enough to allow for a minimalleak through the packing. This slight leakage of the liquid acts as a lubricant as well as acoolant .Obviously, this cannot be allowed for hazardous and toxic liquids.
ال من stuffing boxيحتوى مناسبة كمية طريق packing ringعلى عن وربطها تركيبها يتمgland .يتكون
بين بسيط من packing ringمسار السوائل لمرور العائق المسار هو هذا ويعتبر والعمودالمسار هذا فيعمل خالله
) ( و العمود بين االحتكاك نتيجة الضغط تقليل تكسير العمود packing ringعلى دوران عندمنع على فيعمل
ال تبريد على تعمل السائل من بسيطه تسريب بكمية والسماح ألرتفاع packingالتسريبحتكاك اال نتيجة حرارته
When the liquid being handled is at a higher temperature (above 120 °C), the stuffingbox has an integrally cast water jacket housing. This allows for water circulation andkeeps the pickings at a lower temperature
من االعلى المرتفعة الحرارة درجات لل c °120عند تبريد عمل يتم الداخلى للسائلpacking. التبريد لمياه دائرة طريق عند
Packing ring without cooling Packing ring with cooling
Packing ring Packing
ring
Shaft Shaft
Gland Gland
Cooling water inlet Water jacket
housing
1.3 )Packing Material
In a properly operating stuffing box, the friction losses are usually of the order of 1%of the total pump power. This is independent of the size and kind of pump.The present day packing used in pumps are predominantly made of PTFE
(Teflon/) Graphite filaments.و العمود بين الوقع االحتكاك عن ويعتمد packingينتج للطلمبة الكلية الطاقة فى فقد
ال منها المصنع المادة ونوع المقاس على االيام packingذلك تلك فى يستخدم لذلكPTFE عمل على قدرته بسبب االحتكاك تقليل على يعمل انه .self lubricationحيث
type PTFE packing
1.B) -Packed Plunger Pumps and Piston Pumps
In these pumps, a reciprocating piston (plunger) moves fluid through a chamber bycreating alternate suction and pressure conditions. One-way check valves on theinlet and outlet ports of the pump operate 180° out of phase in order to control fillingof the displacement chamber during suction and to prevent backflow during thedischarge stroke , we used packing to prevent leakage from high pressure side to atmosphere.
بحركة بالسائل الخاصه الحجرة ملىء على تعتمد المضخات من النوع هذا pistonفىالسحب محبس ويغلق الحجرة فتمتلىء السائل بسحب يقوم انه حيث االفقية
ال اخرى مره وغلق pistonويتحركة الطرد محبس فتح فيتم الضغط اتجاة فىلوجود . حاجة فى نكون والطرد السحب عملية اثناء فى السحب packingمحبس
العالى . الضغط منطقة من السائل تسريب لمنع
1.4 )advantage of used packing1 -)This is a simple
التكوين بسيط2 - )low cost, and easy to maintain
الصيانة فى وسهل تكلفة أقل
3 - )Controlled leakage ال ربط طريق عن التسريب فى التحكم packingيمكن
1.5 )Disadvantage of used packing1 -)A persistent leakage and loss of product if the shaft surface is not smooth
المنتج من جزء ويقفد التسريب يزيد العمود خدوشفى وجود حالة .فى 2-)If the gland is too tightened, the shaft/sleeve gets hot and there can be rapid
Wear of the surfaceال ربط حالة او glandفى العمود فى تاكل ويحدث الحرارة درجة ترتفع الرباط وزيادة
الجلبة3-)They require constant supervision..
مستمرة متابعة يلزم
2 - )Mechanical Seal
Mechanical Seal A device used to help prevent leakage and reduce vibration, rotating friction and corrosion of the pump shaft.
Mechanical seal
Cartridge mechanical seal
These mechanical seals are used successfully in noxious and abrasive fluids sealingالتسريب MECHANICAL SEALيستخدم نسبة الن والسامة الضارة السوائل تسريب لمنع
. تنعدم تكاد The mechanical seal is a device that forms a barrier between rotary and stationary
parts in the pump. The seal must block leakage at three pointفى التسريب لمنع واالجزاء 3يستخدم المتحركة االجزاء بين مانع يكون انه حيث نقاط
الثابتة 1)- Between the faces (rotary and stationary) of the seal. 2)- Between the stationary element and the seal chamber housing of the pump. 3)- Between the rotary element and the shaft or sleeve of the pump.
Basic Parts of mechanical seal
431256
Rotating Sealface (1)
Stationary sealface (3)
Secondary sealing elements (2+4)
Spring element (5)
Torque transmission (6)
SINGLE MECHANICAL SEAL (Basic parts )
Rotating Face Stationary Face
Secondary Face(O-Ring )
Spring Element
Heat developement of a sealفى الثابت والجزء المتحرك الجزء بين النسبية الحركة درجة mechanical sealنتيجة ينتج
التسريب وزيادة الجزء ذلك اتالف فى تسبب قد مما المنطقة تلك فى مرتفعة حرارة.
Heat dissipation Face friction
بعمل نقوم المنطقه تلك ولتبريد الحرارة درجة فى ارتفاع حدوث لتفادىflushing
Internal Flushing Recirculation from Discharge to seal chamber
Bypass Flush from Pump Discharge
Orifice (when specified)
Single inside sealAPI Plan 11