1

Medium Voltage Capacitors

Type MSCE and MSCD

Features that matter:

Single and Three-Phase Power Capacitors

Up to 22 kV (50 / 60 Hz)

Up to 1000 kvar

For indoor and outdoor installation

2

Medium Voltage Capacitors

Type MSCE and MSCD

Application

The capacitors are designed for power factor correction

and Harmonic filtration in power network. They are all-

film dielectric and impregnated with an environmen-

tally friendly, Non-PCB biodegradable insulating oil. In

addition each capacitor is provided with an internal

discharge resistor. All FRAKO capacitors comply with

most national and international capacitor standards.

Capacitor benefits to - Improve Power Factor

- Reduce Line Losses

- Decrease Voltage Drop

Through that it helps greater Energy Efficiency.

Product Scope

Power Range: Single Phase 25kvar to 1000kvar

Three Phase 50kvar to 500kvar

Voltage Range: Single Phase 1000V to 22000V

Three Phase 1000V to 11000V

Frequency: 50Hz / 60Hz

Standards: IEC, ANSI / IEEE, NEMA

Technical Specification

Capacitor Losses 0.2 W / kVAr or less with internal fuse

0.15 W / kVAr or less without internal fuse

Ambient Temperature -40°C / A (+40°C) / B (+45°C) / C (+50°C) / D (+55°C)

Over-voltage capability Umax

UN + 10% (up to 8 hours daily)

UN + 15% (up to 30 minutes daily)

UN + 20% (up to 5 minutes)

UN + 30% (up to 1 minute)

Over-current capability Imax IN x 1.3

Painting Color Munsell No. 5Y 7/1

Reference Standard IEC 60871

Bushing Characteristics

BIL

in kV

Creepage

Distance

in mm

Strike

Distance

in mm

Total Height

in mm

60 Hz Withstand Weight

in kg Dry Test Wet Test

60 191 109.2 188.1 60 45 0.87

75 191 109.2 188.1 60 45 0.87

95 318 162.6 235.6 70 55 1.23

150 438 193.0 266.8 80 60 1.75

175 635 223.5 287.9 90 70 2.14

200 720 302.4 388.9 100 80 2.79

The standard terminal size is M12, but M16 could be applied according to rated voltage. Same Bushing is used on 60 and 75kV BIL of capacitor

units. Bird Cap and Parallel-groove connector with all bushings are supplied, and it is applicable to Copper or Aluminum conductor [14~100mm²

2line]. Applied bushing could be changed by special requirements.

3

Medium Voltage Capacitors

Type MSCE

Single Phase Capacitor - Insulation Level 36 kV [50/150]

Capacitor without Internal Fuse

System Rated Voltage: 33000, 30000 V

Capacitor Rated Voltage: 19050/9530, 17320/8660 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 260 530 430 145 27

200 130 430 700 430 145 42

300 180 580 850 430 145 55

400 220 630 900 430 175 69

500 220 760 1030 430 175 82

600 220 880 1150 430 175 94

700 220 1030 1300 430 175 109

800 220 1180 1450 430 175 123

900 220 1200 1470 430 175 126

1000 220 1280 1550 430 175 134

Capacitor with Internal Fuse

System Rated Voltage: 33000, 30000 V

Capacitor Rated Voltage: 9530, 8660 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

300 220 630 900 430 145 59

400 220 830 1100 430 145 76

500 220 830 1100 430 175 89

600 220 980 1250 430 175 104

700 220 1130 1400 430 175 120

800 220 1160 1430 430 175 123

900 220 1300 1570 430 175 138

1000 220 1430 1700 430 175 151

Single-Bushing Capacitor also could be provided. Applied bushing could be changed by special requirements [See table under Bushing Charac-

teristics]. Approximate dimensions and weights are given above. Please contact to factory for exact dimensions of a particular unit before order.

4

Medium Voltage Capacitors

Type MSCE

Single Phase Capacitor - Insulation Level 24 kV [50/125]

Capacitor without Internal Fuse

System Rated Voltage: 24000 V

Capacitor Rated Voltage: 13860/6930 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 260 530 430 145 28

200 130 430 700 430 145 42

300 180 600 870 430 145 57

400 220 660 930 430 175 72

500 220 800 1070 430 175 87

600 220 960 1230 430 175 102

700 220 1080 1350 430 175 115

800 220 1130 1400 430 175 120

900 220 1160 1430 430 175 123

1000 220 1260 1530 430 175 134

Capacitor with Internal Fuse

System Rated Voltage: 24000 V

Capacitor Rated Voltage: 13860/6930 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

200 180 600 870 430 115 47

300 220 660 930 430 145 62

400 220 860 1130 430 145 79

500 220 860 1130 430 175 93

600 220 1030 1300 430 175 111

700 220 1180 1450 430 175 126

800 220 1200 1470 430 175 130

900 220 1260 1530 430 175 135

1000 220 1400 1670 430 175 149

Single-Bushing Capacitor also could be provided. Applied bushing could be changed by special requirements [See table under Bushing Charac-

teristics]. Approximate dimensions and weights are given above. Please contact to factory for exact dimensions of a particular unit before order.

5

Medium Voltage Capacitors

Type MSCE

Single Phase Capacitor - Insulation Level 17.5 kV [38/95]

Capacitor without Internal Fuse

System Rated Voltage: 15000 V

Capacitor Rated Voltage: 8660 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 260 530 430 145 28

200 130 430 700 430 145 42

300 180 600 870 430 145 57

400 220 660 930 430 175 72

500 220 800 1070 430 175 87

600 220 960 1230 430 175 102

700 220 1080 1350 430 175 115

800 220 1130 1400 430 175 120

900 220 1160 1430 430 175 123

1000 220 1260 1530 430 175 134

Capacitor with Internal Fuse

System Rated Voltage: 15000, 13800 V

Capacitor Rated Voltage: 8660, 7970 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

300 220 660 890 430 145 61

400 220 830 1060 430 145 75

500 220 830 1060 430 175 88

600 220 1000 1230 430 175 106

700 220 1160 1390 430 175 122

800 220 1200 1430 430 175 127

900 220 1300 1530 430 175 140

1000 220 1460 1690 430 175 153

Single-Bushing Capacitor also could be provided. Applied bushing could be changed by special requirements [See table under Bushing Charac-

teristics]. Approximate dimensions and weights are given above. Please contact to factory for exact dimensions of a particular unit before order.

6

Medium Voltage Capacitors

Type MSCE

Single Phase Capacitor - Insulation Level 12 kV [28/75]

Capacitor without Internal Fuse

System Rated Voltage: 12000, 11000 V

Capacitor Rated Voltage: 6930, 6350 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 260 445 430 145 27

200 130 430 615 430 145 42

300 180 580 765 430 145 55

400 180 630 815 430 175 69

500 220 780 965 430 175 84

600 220 930 1115 430 175 99

700 220 1060 1245 430 175 113

800 220 1180 1365 430 175 125

900 220 1200 1385 430 175 127

1000 220 1300 1485 430 175 134

Capacitor with Internal Fuse

System Rated Voltage: 12000, 11000 V

Capacitor Rated Voltage: 6930, 6350 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

200 180 580 765 430 115 45

300 220 630 815 430 145 59

400 220 830 1015 430 145 76

500 220 830 1015 430 175 90

600 220 980 1165 430 175 105

700 220 1160 1345 430 175 123

800 220 1180 1365 430 175 126

900 220 1300 1485 430 175 135

1000 220 1430 1615 430 175 148

Single-Bushing Capacitor also could be provided. Applied bushing could be changed by special requirements [See table under Bushing Charac-

teristics]. Approximate dimensions and weights are given above. Please contact to factory for exact dimensions of a particular unit before order.

7

Medium Voltage Capacitors

Type MSCE

Single Phase Capacitor - Insulation Level 7.2 kV [20/60]

Capacitor without Internal Fuse

System Rated Voltage: 7200, 6600, 6300, 6000 V

Capacitor Rated Voltage: 4160, 3800, 3640, 3460 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 260 445 430 145 27

200 130 430 615 430 145 41

300 180 560 745 430 145 52

400 220 630 815 430 175 68

500 220 760 945 430 175 81

Capacitor with Internal Fuse

System Rated Voltage: 7200, 6600, 6300, 6000 V

Capacitor Rated Voltage: 4160, 3800, 3640, 3460 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

200 180 580 745 430 115 43

300 220 630 815 430 145 57

400 220 800 985 430 145 72

500 220 800 985 430 175 85

Applied bushing could be changed by special requirements [See table under Bushing Characteristics]. Approximate dimensions and weights are

given above. Please contact to factory for exact dimensions of a particular unit before order.

8

Medium Voltage Capacitors

Type MSCD

Three Phase Capacitor - Insulation Level 12 kV [28/75]

Capacitor

System Rated Voltage: 11000 V

Capacitor Rated Voltage: 11000 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 280 465 430 145 30

200 130 450 635 430 145 44

300 180 620 805 430 145 59

400 220 680 865 430 175 74

500 220 810 995 430 175 87

Capacitor

System Rated Voltage: 7200, 6600, 6300, 6000 V

Capacitor Rated Voltage: 7200, 6600, 6300, 6000 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

100 130 280 465 430 145 29

200 130 420 605 430 145 41

300 180 600 785 430 145 56

400 220 620 805 430 175 67

500 220 790 975 430 175 83

Applied bushing could be changed by special requirements [See table under Bushing Characteristics] Approximate dimensions and weights are

given above. Please contact to factory for exact dimensions of a particular unit before order. Brackets are optional.

Three Phase Capacitor - Insulation Level 7.2 kV [20/60]

9

Medium Voltage Capacitors

Type MSCD

Three Phase Capacitor - Insulation Level 7.2 kV [20/60]

Capacitor with Unbalanced Protection

System Rated Voltage: 7200, 6600, 6300, 6000 V

Capacitor Rated Voltage: 7200, 6600, 6300, 6000 V

Power

in kvar

Dimensions in mm Weight

in kg A B C D E

150 220 380 565 430 145 37

200 220 480 665 430 145 43

300 220 620 805 430 145 56

400 220 700 885 430 175 69

500 220 830 1015 430 175 82

Applied bushing could be changed by special requirements [See table

under Bushing Characteristics]. Approximate dimensions and weights are

given above. Please contact to factory for exact dimensions of a particu-

lar unit before order. Brackets are optional.

10

Capacitor innovation, development

and production since 1928

Check out other FRAKO Products

AC Power Capacitors

Dry type design

240 V to 800 V, up to 40 kvar

High current capability up to 2.7

nominal capacitor current (50 Hz)

Ambient temperature up to 68°C

Altitude up to 4,000 meters

Patented terminals offer fast, anti-

vibration and maintanance free wiring

Capacitor Switching Contactors

Patented design with significant

damping of inrush current

Long life, tested for up to 100,000

switchings

High reliability and low power losses

Available for use in systems with or

without reactors

Also available with

following agency

approvals:

FRAKO Kondensatoren- und Anlagenbau GmbH

Tscheulinstr. 21a ● 79331 Teningen ● Germany

Phone: +49 7641 453-0 ● Fax: +49 7641 453-545

E-Mail: info@frako.com ● Internet: www.frako.com