Rugged
Pre-Calibrated Ranges
Monitoring and Control Solutions
microBlox® Series Brochure
High-Density Analog I/OSignal Conditioners
Wireless Configuration
Tel: 877-214-6267 ■ [email protected] ■ www.acromag.com ■ 30765 Wixom Rd, Wixom, MI 48393 USA
Bulletin #8400-890b
Acromag Inc877-214-6267 ■ [email protected] ■ www.acromag.com
MicroBlox® Series Featuring Bluetooth® Wireless Technology
IntroductionAcromag’s microBlox® uB Series I/O modules offer a com-pact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measure-ment, and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
microBlox I/O Modules Advantages
■ Selection of 175 I/O modules with Bluetooth® wireless technology capability, fixed-range, and cost-saving commercial grade versions.
■ User-configurable I/O ranges with smartphone or tablet.
■ Input polling with trend charts in Android® or iOS® app.
■ Alarm output function with setpoint and deadband.
■ 1500V AC isolation field-to-host and channel-to-channel.
■ Up to 0.05% accuracy and 130db CMR.
■ Shock and vibration-resistant without screws.
– 2 –
Innovative Signal Conditioning
User-configurable & Fixed I/O Range Models Available
Input Modules
uB30/uB40 ±10mV to ±100mV input, 0-5V or ±5V output
uB31/uB41 ±1V to ±60V input, 0-5V or ±5V output
uB32 0-20mA or 4-20mA DC input, 0-5V or ±5V output
uB34/uB35 RTD input, 0-5V or ±5V output
uB37/47 Thermocouple input, 0-5V or ±5V output
uB422-wire transmitter (0-20mA) input, 0-5V or ±5V output
uB45 0-50KHz input, 0-5V or ±5V output
Output Modules
uB390-20mA or 4-20mA DC field output, ±5V host input
uB49 0-10V or ±10V field output, ±10V host input
Backpanels
uB04/uB04D 4 channel uB backpanel, surface or DIN-rail mount
uB08/uB08D 8 channel uB backpanel, panel or DIN-rail mount
uB16/uB16D 16 channel uB backpanel, panel or DIN-rail mount
Power Options
uBDC1 5V DC power module, 10-32V DC supply input
Signal Conditioners: microBlox® SeriesKey Features
DB25 cable simplifies connection to DAQ systems
Analog Bus Port
95 modules support a wide variety of input and output signal types
5V power modules enables use of 10-32V supplies
Flexible Power
User-Programmable I/O Ranges
Models with Bluetooth wireless technology allow custom input and output ranges
Wireless Configuration
Easily set I/O scaling and alarms or poll inputs using Bluetooth wireless technology with a smartphone or tablet using Android or iOS app.
Wireless (-B) models support alarm setpoint/deadband control to drive 0 or 5V output
Alarm Function
Superior shock, vibration, moisture, and dust protection
Rugged, Over-molded Circuit
High-accuracy / high noise immunity
High-performance
-40 to 80 C̊-40 to 80 C̊
Easy, Secure Mounting
Clip holds module tighly without screws for fast insertion/removal
Mix-and-Match Modules
High-Density Analog I/O
Up to 16 channels in a compact footprint
Tel 248-295-0880 ■ [email protected] ■ www.acromag.com ■ 30765 Wixom Rd, Wixom, MI 48393 USA
– 3 –
IP Description
– 4 –
Tel 248-295-0880 ■ [email protected] ■ www.acromag.com ■ 30765 Wixom Rd, Wixom, MI 48393 USA
microBlox® Transmitting AlarmsThe uBTA carriers are used with Acromag’s microBlox® signal conditioning modules to create powerful alarms that also pro-vide a voltage/current transmitter output. The plug-in modules offer the convenience of wireless field programming on a smartphone or tablet.
The microBlox uB modules offer a space saving solution for isolating, monitoring, and converting sensor signals to interface with your data acquisition or control system. By inserting a uB input module into a single or dual channel carrier, you get a device with both alarm and transmitter capabilities. With a broad selection of uB input modules, you can monitor many different signal types by simply interchanging modules on the carrier.
microBlox® Transmitting Alarms Advantages
■ Single/dual alarms with two independent mechanical or solid-state relays, up to 5A switching.
■ Transmitter output with 4-20mA and 0-5V signal ranges.
■ Interchangeable input modules for measuring a wide variety of signal types.
■ Easy configuration using Bluetooth® wireless technology.
Innovative Signal Conditioning
MicroBlox® Series Splitter and Combination Transmitter/Alarms
microBlox® Transmitting Alarms Selection Guide
Carriers
uBTA-H-1MR uBTA-H-1SR
Single transmitter/alarm in housing; mechanical or solid-state relays.
uBTX-H-1 Single transmitter in housing.
uBTA-P-1MR uBTA-P-1SR
Single transmitter/alarm, panel mount; mechanical or solid-state relays.
uBTA-P-2MR uBTA-P-2SR
Dual transmitter/alarm, panel mount; mechanical or solid-state relays.
uBSP-P-1Dual tandem analog current and voltage outputs signal splitter
Modules: Plug-In Analog Field Input Modules
uB30-B uB40-B
DC millivolt input, 5Hz bandwidth (uB30-B) or 1kHz bandwidth (uB40-B); Configurable ±100mV.
uB31-B uB41-B
DC voltage input, 4Hz bandwidth (uB31-B) or 1kHz bandwidth (uB41-B); Configurable ±1- ±60V.
uB32-B uB42-B
DC current input (uB32-B); optional 2-wire loop excitation (uB42-B) ; Configurable 0-20mA.
uB34-B uB35-B
Pt RTD input; 2 or 3-wire (uB34-B) or 4-wire (uB35-B); Configurable 0-600°C.
uB37-B uB47-B
Thermocouple input, non-linearized (uB37-B) or linearized (uB47B); Configurable Type J,K,T,R,S.
Input High-Alarm
Time
Deadband
Time
Input Low-Alarm
Deadband
Deadband
Deadband
Time
Input
Tel 248-295-0880 ■ [email protected] ■ www.acromag.com ■ 30765 Wixom Rd, Wixom, MI 48393 USA
Signal Conditioners: microBlox®Series
Bulletin #8400-894c
The Agility™ Config Tool is a mobile applica-tion that allows easy setup and configuration of Acromag microBlox® Series signal conditioners and alarms.
You can download the Agility application free of charge from the Google PlayTM store at play.google.com (Android), or the Apple® App Store® at itunes.apple.com (Apple iOS).
Demo the software, no need for a module. To enter demo mode simply tap the icon in the upper left corner 8 times.
Acromag Agility™ Config Tool Mobile Application
Key Features & Benefits■ Connects to microBlox signal conditioners via
Bluetooth wireless technology
■ Requires the use of a smart device
■ Configures and calibrates microBlox UB Series products via phone or tablet running Android 4.3 or later or iOS 8.1 or later.
■ View wiring diagrams, even without an inter-net connection
■ Perform quick and easy field diagnostics and troubleshooting
■ Ideal for field technicians
■ Trend and share field dataWith a couple of taps, quickly configure input, output, unit and scaling options.
Quick and easy access to the wiring diagram, even offline without internet access.
– 5 –– 5 –
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Acromag is under license other trademarks are property of their respective owners. Copyright © Acromag, Inc. 2019. Data subject to change without notice. Printed in USA 10/2019
Tel 248-295-0880 ■ [email protected] ■ www.acromag.com ■ 30765 Wixom Rd, Wixom, MI 48393 USA
Acromag Agility™ Config Tool Mobile Application
Signal Conditioners: microBlox®Series
SETPOINT (sp)
SETPOINT (sp)
DEADBAND (DB)
HIGH-ALARM WITH DEADBAND(REVERSE ACTING ALARM OUTPUT OFF)
LOW-ALARM WITH DEADBAND(REVERSE ACTING ALARM OUTPUT OFF)
DEADBAND (DB)
TIME TIME
INPUT
INPUT SIGNAL
INPUT SIGNALSP
SP-DB
t1 t2
INPUT
NORMAL STATE ALARM STATE NORMAL STATE(OUT ZERO)
t1 IS TIME INPUT SIGNAL INCREASES TO SPt1 IS TIME INPUT DECREASES TO SP MINUS DB
t1 IS TIME INPUT SIGNAL DECREASES TO SPt1 IS TIME INPUT INCREASES TO SP PLUS DB
(OUT FULL-SCALE) (OUT ZERO)
NORMAL STATE ALARM STATE NORMAL STATE(OUT ZERO) (OUT FULL-SCALE) (OUT ZERO)
SP
SP-DB
t1 t2
Alarm Function
Calibration Data Logging Diagnostics
Tel 248-295-0880 ■ [email protected] ■ www.acromag.com ■ 30765 Wixom Rd, Wixom, MI 48393 USA
The microBlox® I/O FamilyMODEL FIELD I/O, Min Bandwidth HOST I/OuB30-B IN: Config ±10 to ±100mV, 5Hz Config ±5V
uB30-01 IN: ±10mV, 5Hz OUT: ±5V
uB30-02 IN: ±50mV, 5Hz OUT: ±5V
uB30-03 IN: ±100mV, 5Hz OUT: ±5V
uB30-04 IN: ±10mV, 5Hz OUT: 0-5V
uB30-05 IN: ±50mV, 5Hz OUT: 0-5V
uB30-06 IN: ±100mV, 5Hz OUT: 0-5V
uB40-B IN: Config ±10 to ±100mV, 1KHz Config ±5V
uB40-01 IN: ±10mV, 1KHz OUT: ±5V
uB40-02 IN: ±50mV, 1KHz OUT: ±5V
uB40-03 IN: ±100mV, 1KHz OUT: ±5V
uB40-04 IN: ±10mV, 1KHz OUT: 0-5V
uB40-05 IN: ±50mV, 1KHz OUT: 0-5V
uB40-06 IN: ±100mV, 1KHz OUT: 0-5V
uB31-B IN: Config ±1 to ±60V, 4Hz Config ±5V
uB31-01 IN: ±1V, 4Hz OUT: ±5V
uB31-02 IN: ±5V, 4Hz OUT: ±5V
uB31-03 IN: ±10V Input, 4Hz OUT: ±5V
uB31-04 IN: ±1V Input, 4Hz OUT: 0-5V
uB31-05 IN: ±5V Input, 4Hz OUT: 0-5V
uB31-06 IN: ±10V Input, 4Hz OUT: 0-5V
uB31-07 IN: ±20V Input, 4Hz OUT: ±5V
uB31-08 IN: ±20V Input, 4Hz OUT: 0-5V
uB31-09 IN: ±40V Input, 4Hz OUT: ±5V
uB31-10 IN: ±40V Input, 4Hz OUT: 0-5V
uB31-12 IN: ±60V Input, 4Hz OUT: ±5V
uB31-13 IN: ±60V Input, 4Hz OUT: 0-5V
uB41-B IN: Config ±1 to ±60V, 1KHz Config ±5V
uB41-01 IN: ±1V, 1KHz OUT: ±5V
uB41-02 IN: ±5V, 1KHz OUT: ±5V
uB41-03 IN: ±10V, 1KHz OUT: ±5V
uB41-04 IN: ±1V, 1KHz OUT: 0-5V
uB41-05 IN: ±5V, 1KHz OUT: 0-5V
uB41-06 IN: ±10V, 1KHz OUT: 0-5V
uB41-07 IN: ±20V, 1KHz OUT: ±5V
uB41-08 IN: ±20V, 1KHz OUT: 0-5V
uB41-09 IN: ±40V, 1KHz OUT: ±5V
uB41-10 IN: ±40V, 1KHz OUT: 0-5V
uB41-12 IN: ±60V, 1KHz OUT: ±5V
uB41-13 IN: ±60V, 1KHz OUT: 0-5V
uB32-B IN: Config 0-20mA, 7Hz Config ±5V
uB32-01 IN: 4-20mA, 7Hz OUT: 0-5V
uB32-02 IN: 0-20mA, 7Hz OUT: 0-5V
uB32-03 IN: 0-11.17mA, 7Hz OUT: 0-5V
uB34-B IN: Pt RTD, Config 0-600C Config ±5V
uB34-01 IN: Pt RTD, ±100C, 3Hz OUT: 0-5V
uB34-02 IN: Pt RTD, 0-100C, 3Hz OUT: 0-5V
uB34-03 IN: Pt RTD,0-200C, 3Hz OUT: 0-5V
uB34-04 IN: Pt RTD, 0-600C, 3Hz OUT: 0-5V
uB35-B IN: 4W Pt RTD, Config 0-600C Config ±5V
uB35-01 IN: 4W Pt RTD, ±100C, 3Hz OUT: 0-5V
uB35-02 IN: 4W Pt RTD, 0-100C, 3Hz OUT: 0-5V
uB35-03 IN: 4W Pt RTD,0-200C, 3Hz OUT: 0-5V
uB35-04 IN: 4W Pt RTD, 0- OUT: 0-5V
MODEL FIELD I/O, Min Bandwidth HOST I/OuB37-B IN: Config J/K/T/R/S Non-Lin, 5Hz Config ±5V
uB37J IN: J TC -100-760C, Non-Lin, 5Hz OUT: 0-5V
uB37K IN: K TC -100-1350C, Non-Lin, 5Hz OUT: 0-5V
uB37T IN: T TC -100-400C, Non-Lin, 5Hz OUT: 0-5V
uB37R IN: R TC 0-1750C, Non-Lin, 5Hz OUT: 0-5V
uB37S IN: S TC 0-1750C, Non-Lin, 5Hz OUT: 0-5V
uB47-B IN: Config TC J/K/T Lin, 5Hz Config ±5V
uB47J-01 IN: J TC 0-760C, Lin, 5Hz OUT: 0-5V
uB47J-02 IN: J TC -100-300C, Lin, 5Hz OUT: 0-5V
uB47J-03 IN: J TC 0-500C, Lin, 5Hz OUT: 0-5V
uB47J-12 IN: J TC -100-760C, Lin, 5Hz OUT: 0-5V
uB47K-04 IN: K TC 0-1000C, Lin, 5Hz OUT: 0-5V
uB47K-05 IN: K TC 0-500C, Lin, 5Hz OUT: 0-5V
uB47K-13 IN: K TC -100-1350C, Lin, 5Hz OUT: 0-5V
uB47K-14 IN: K TC 0-1200C, Lin, 5Hz OUT: 0-5V
uB47T-06 IN: T TC -100-400C, Lin, 5Hz OUT: 0-5V
uB47T-07 IN: T TC 0-200C, Lin, 5Hz OUT: 0-5V
uB39-B OUT: Config 0-20mADC, 100Hz Config: ±5V
uB39-01 OUT: 4-20mA, 100Hz IN: 0-5V
uB39-02 OUT: 4-20mA, 100Hz IN: ±5V
uB39-03 OUT: 0-20mA, 100Hz IN: 0-5V
uB39-04 OUT: 0-20mA, 100Hz IN: ±5V
uB42-B IN: Config 0-20mA w/EXC, 100Hz Config ±5V
uB42-01 IN: 4-20mA w/ 2-W EXC, 100Hz OUT: 0-5V
uB42-02 IN: 4-20mA w/ 2-W EXC, 100Hz OUT: 1-5V
uB45-B IN: Config 0-50KHz Frequency Config: ±5V
uB45-01 IN: 0-500Hz Frequency OUT: 0-5V
uB45-02 IN: 0-1K0Hz Frequency OUT: 0-5V
uB45-03 IN: 0-2.5KHz Frequency OUT: 0-5V
uB45-04 IN: 0-5KHz Frequency OUT: 0-5V
uB45-05 IN: 0-10KHz Frequency OUT: 0-5V
uB45-06 IN: 0-25KHz Frequency OUT: 0-5V
uB45-07 IN: 0-50KHz Frequency OUT: 0-5V
uB49-B OUT: Config to ±10V, 100Hz Config ±5V
uB49-01 OUT: 0-5V, 100Hz IN: ±5V
uB49-02 OUT: ±5V, 100Hz IN: ±5V
uB49-03 OUT: ±5V, 100Hz IN: 0-5V
uB49-04 OUT: 0-10V, 100Hz IN: ±10V
uB49-05 OUT: ±10V, 100Hz IN: ±10V
uB49-06 OUT: ±10V, 100Hz IN: 0-10V
uB49-07 OUT: ±5V, 100Hz IN: ±10V
ACCESSORIESuBDC1 Non-Isolated, 10-32V: 5V/1A Power Supply
uB04 4 Channel Panel, Surface Mount Only
uB04D 4 Channel Panel, Surface or DIN Rail Mount
uB08 8 Channel Panel, Surface Mount Only
uB08D 8 Channel Panel, Surface or DIN Rail Mount
uB016 16 Channel Panel, Surface Mount Only
uB016D 16 Channel Panel, Surface or DIN Rail Mount
uBDN4/8/16 uB04/8/16 Surface to DIN Rail Mount Conversion Kits
5020-350 AC Current Sensor, 0-11.17mA
Bulletin #8401-038b 2019 Acromag, Incorporated
