micron PUR LCGear pumpThis particular version of ‘micron gear series’ has been designed to be used with 2kg PUR blocks adhesive. The gear pump allows an equal and precise glue application by a control of the glue quantity through the gear speed.

Multifunctional electronic controlThis new development combines the electronic ‘meler’ control that

allows a very userfriendly handling and very effective and intuitive motor control.

Easy AccessThe easy access to all the components of the ‘micron PUR LC’ is a big advantage in reference to others models. It allows a fast access to all internal components of the system (motor, controls,…) by the use of a double side-opening door, which provides total accessibility.

ConnectionsThe hose connections of the ‘micron PUR LC’ can be installed at the rear side of the system, close to the main machine. Two hoses per pump

and manifold can be installed with a maximum of two pumps per unit.

TankAs the other ‘micron gear’ units the ‘micron PUR LC’ version has a large

tank loading zone, as well as a tank drain valve, making its filling and emptying easier. In addition, it includes a large contact zones, providing an optimal fusion rate.

In this particular version the lid is completely air-tight (with double closing system) and includes the installation to guarantee a non moisture atmosphere inside the tank to prevent adhesive’s reaction. As an option you can order the air-dryer assembly or not.

Motor-pumpThe assembly of motor-gearbox-pump guarantees an equal hot-melt supply, which is controlled by the motor rotation speed.

CompatibilityThe ‘micron PUR LC’ can be equipped with Pt100 as well as with Ni120 sensor technology. Therefore it is compatible with most of the commom hot-melt systems in the market.

SafetyThe by-pass valve ensures, that excess pressure situations are avoided in the system. It also allows to maintain a constant system pressure even in intermittent applications with closed, non applying guns.

Likewise air-dryer control guarantees a completely safety operation due to the detection of opening lid to remove the internal pressure in the tank.

MELER GROUPCorporate HeadquartersE-mail: info@meler.es

w w w . m e l e r . e uP.I. Los Agustinos, Calle-G, Nave-D-43E-31160 ORCOYEN. Navarra (Spain)Tel.: +34 948 351 110 - Fax.: +34 948 351 130

TECHNICAL CHARACTERISTICSTank volume 4 liters for 2 kg PUR blocks (air-tight lid)Pumping rate 4 cc/rev single pump (*)Melting rate 6 kg/h (*)Number of pumps 1Number of outputs 2 Motor power 250 WPump speed 0-100 rpm (10-80 rpm recommended)Temperature range 40 to 200ºCTemperature control RTD ±0,5ºCMax. working pressure 90 bar (1.305 psi)Pressure relief valve pneumatic (standard)Max. input power 5.750 W (230V 1~ 50/60 Hz) 2.900 W per phase (400V 3~ 50/60 Hz + N)External functions Temperatures ok output Low level output (with external ligth beacon) External standby activation Outputs enabled external control Motor ON/OFF external contact Motor speed external controlElectrical connection 230V 1~ 50/60 Hz + N + PE 230V 3~ 50/60 Hz + N + PE 400V 3~ 50/60 Hz + N + PEDimensions see drawingOptions temperature control technology (Pt100 or Ni120) air-dryer assembly (pre-installation included as standard)

* Depending on adhesive type

C 03

0 - E

NG -

V311

- M

ELER

rese

rves

the

right

to m

odify

the

cont

ents

of th

is ca

talog

ue w

ithou

t not

ice

724

709 83

9

608

30843

070

9