©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
MANUAL: Hand Held AutomaticDual Pressure Nozzles
Mid-Force, CAFS-Force and Dual-ForceINSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE
WARNINGUnderstand manual before use. Operation of this device without understanding the manual and receiving proper training is a misuse of this equipment. Obtain safety information at www.tft.com/serial-number
TASK FORCE TIPS, INC.MADE IN USA • www.tft.com
3701 Innovation Way, Valparaiso, IN 46383-9327 USA800-348-2686 • 219- 462-6161 • Fax 219-464-7155
DANGERPERSONAL RESPONSIBILITY CODE
The member companies of FEMSA that provide emergency response equipment and services want responders to know and understand the following:1. Firefi ghting and Emergency Response are inherently dangerous activities
requiring proper training in their hazards and the use of extreme caution at all times.
2. It is your responsibility to read and understand any user’s instructions, including purpose and limitations, provided with any piece of equipment you may be called upon to use.
3. It is your responsibility to know that you have been properly trained in Firefi ghting and /or Emergency Response and in the use, precautions, and care of any equipment you may be called upon to use.
4. It is your responsibility to be in proper physical condition and to maintain the personal skill level required to operate any equipment you may be called upon to use.
5. It is your responsibility to know that your equipment is in operable condition and has been maintained in accordance with the manufacturer’s instructions.
6. Failure to follow these guidelines may result in death, burns or other severe injury.
FEMSA Fire and Emergency Manufacturers and Service AssociationP.O. Box 147, Lynnfi eld, MA 01940 • www.FEMSA.org
MID-FORCE with IMPULSE
Trigger Valve System
MID-FORCE with BailValve Handle
DUAL-FORCE with BailValve Handle
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev162
Table Of Contents1.0 MEANING OF SAFETY SIGNAL WORDS2.0 SAFETY3.0 GENERAL INFORMATION 3.1 VARIOUS MODELS AND TERMS 3.2 SPECIFICATIONS 3.2.1 MECHANICAL 3.3 NOZZLE COUPLINGS 3.4 USE WITH SALT WATER4.0 FLOW CHARACTERISTICS 4.1 FLOW GRAPHS 4.2 FLOW AND REACTION CHARTS 4.3 REACH AND TRAJECTORY5.0 NOZZLE CONTROLS 5.1 FLOW CONTROL 5.1.1 LEVER TYPE FLOW CONTROL 5.1.2 TIP ONLY 5.1.3 BALL SHUT-OFF 5.1.4 TWIST SHUT-OFF 5.1.5 IMPULSE TRIGGER FLOW CONTROL 5.1.5.1 IMPULSE TRIGGER LOCK 5.1.5.2 TRIGGER FLOW CONTROL SPEED ADJUSTMENT 5.1.5.3 NORMAL OPERATING POSITION 5.2 PATTERN CONTROL ADJUSTMENT 5.2.1 PATTERN CONTROL 5.2.2 FLUSH CONTROL 5.3 STANDARD/LOW PRESSURE KNOB MID-FORCE & DUAL-FORCE6.0 USE WITH FOAM 6.1 FOAM ASPIRATING ATTACHMENTS7.0 USE OF NOZZLES 7.1 MID-FORCE AND DUAL-FORCE NOZZLES 7.2 CAFS-FORCE 1 AND CAFS-FORCE 2 NOZZLES8.0 APPROVALS9.0 COLOR CODED VALVE HANDLE AND PISTOL GRIP 9.1 IMPULSE TRIGGER VALVE SYSTEM NOZZLE COLORED PISTOL GRIPS10.0 WARRANTY11.0 MAINTENANCE 11.1 FIELD LUBRICATION 11.2 IMPULSE TRIGGER VALVE LUBRICATION 11.3 SERVICE TESTING 11.3.1 HYDROSTATIC TESTING 11.3.2 FLOW TESTING 11.3.3 RECORDS 11.4 REPAIR12.0 OPERATION and INSPECTION CHECKLIST
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev163
1.0 MEANING OF SAFETY SIGNAL WORDSA safety related message is identifi ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular hazard. Per ANSI standard Z535.6-2011, the defi nitions of the four signal words are as follows:
DANGERDANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNINGWARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTIONCAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICENOTICE is used to address practices not related to physical injury.
2.0 SAFETY
DANGER An inadequate supply of nozzle pressure and/or fl ow will cause an ineff ective stream and can result in injury, death, or loss of property. See fl ow graphs or call 800-348-2686 for assistance.
WARNINGThe nozzle may be damaged if frozen while containing signifi cant amounts of water. Such damage may be diffi cult to detect visually and can lead to possible injury or death. Any time the nozzle is subject to possible damage due to freezing, it must be tested by qualifi ed personnel before being considered safe for use.
WARNINGThis equipment is intended for use by trained personnel for fi refi ghting. Their use for other purposes may involve hazards not addressed by this manual. Seek appropriate guidance and training to reduce risk of injury.
WARNINGFailure to restrain nozzle reaction can cause fi refi ghter injury from loss of footing and/or stream protection. Nozzle reaction will vary as supply conditions change: such as opening or closing other nozzles, hose line kinks, changes in pump settings, etc. Changes in spray pattern or fl ushing will also aff ect nozzle reaction. The nozzle operator must always be prepared in the event of these changes.
WARNINGIf nozzle gets out of control or away from operator, retreat from nozzle immediately. Do not attempt to regain control of nozzle while fl owing water. Injury from whipping can occur.
WARNINGWater is a conductor of electricity. Application of water on high voltage equipment can cause injury or death by electrocution. The amount of current that may be carried back to the nozzle will depend on the following factors:
• Voltage of the line or equipment• Distance from the nozzle to the line or equipment• Size of the stream• Whether the stream is solid or broken• Purity of the water1
1 The Fire Fighter and Electrical Equipment, The University of Michigan Extension Service, Fourth Printing 1983. Page 47
CAUTIONFire streams are capable of injury and damage. Do not direct water stream to cause injury or damage to persons or property.
3.0 GENERAL INFORMATIONThe Task Force Tips nozzles are designed to provide excellent performance under most fi refi ghting conditions. Their rugged construction is compatible with the use of fresh water as well as fi refi ghting foam solutions. Other important operating features are:
• Switchable from standard operation to low pressure• Automatic pressure regulation (meets NFPA 1964 automatic nozzle pressure requirements)• Slide valve for excellent stream quality at all valve positions• Quick-acting pattern control from straight stream to wide fog• “Power fog teeth” for full-fi ll fog• “Gasket grabber” inlet screen to keep large debris from entering nozzle• Easily fl ushable while fl owing to clear trapped debris• TFT’s fi ve-year warranty and unsurpassed customer service
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev164
3.1 VARIOUS MODELS AND TERMSThe nozzle is available in several diff erent models and inlet connections. Basic body styles are shown in fi gure 3.1A
SERIES FLOW RANGE NOMINAL PRESSURE STANDARD COUPLING*GPM L/min PSI BAR
MID-FORCE 70-200 265-760 100 7 1-1/2 NHMID-FORCE 70-200 265-760 75 5 1-1/2 NH
DUAL-FORCE 95-300 360-1150 100 7 1-1/2 NHDUAL-FORCE 95-300 360-1150 75 5 1-1/2 NHCAFS-FORCE1 70-200 265-760 75 5 1-1/2 NHCAFS-FORCE2 95-250 360-950 75 5 1-1/2 NH
* Other threads, coupling sizes, or connector styles can be specifi ed at time of order.
COUPLING
RUBBERGASKET
PISTOLGRIP
STREAMSHAPER
NOZZLE WITH VALVEnd INTEGRAL PISTOL GRIPa
FLOW
CONTROL
ON OFF
TIP ONLY NOZZLE
BARREL LABEL
NAME LABEL
PRESSURECONTROLKNOB
VALVE HANDLE
NOZZLE WITH VALVE
GASKETGRABBERINLETSCREEN
DETENTS
MID-FORCE andDUAL-FORCE only
TIP ONLY NOZZLE WITH TWIST SHUTOFF
VALVE POSITIONLABEL
VALVE RING
NOZZLE WITH IMPULSE TRIGGER VALVE SYSTEM
OFFON
TRIGGER
4 POSITION LOCK
3.1A COMMON MODELS AND TERMS
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev165
3.2 SPECIFICATIONS3.2.1 MECHANICAL
Maximum nozzle inlet pressure with valve shutoff
300 psi 21 bar
Operating temperature range of fl uid 33 to 120º F 1 to 50º CStorage temperature range -40 to 150º F -40 to 65º CMaterials used Aluminum 6000 series hard anodized MIL8625 class 3 type 2,
stainless steel 300 series, nylon 6-6, nitrile rubber
3.3 NOZZLE COUPLINGSMany inlet couplings such as NH (National Hose) or NPSH (National Pipe Straight Hose) can be specifi ed at time of order.
CAUTIONNozzle must be mated to a hose line with matched threads. Mismatched or damaged threads may cause nozzle to leak or uncouple under pressure and could cause injury.
CAUTIONDissimilar metals coupled together can cause galvanic corrosion that can result in the inability to unscrew the threads or complete loss of thread engagement over time. Per NFPA 1962, if dissimilar metals are left coupled together an anti-corrosive lubricant should be applied to the threads. Also the coupling should be disconnected and inspected at least quarterly.
3.4 USE WITH SALT WATERUse with saltwater is permissible provided nozzle is thoroughly cleaned with fresh water after each use. The service life of the nozzle may be shortened due to the eff ects of corrosion and is not covered under warranty.
4.0 FLOW CHARACTERISTICSThe following graphs show the typical performance of MID-FORCE, CAFS-FORCE and DUAL-FORCE nozzles.
SPECIAL CONFIGURATIONS - If nozzles are made according to the special marking or performance requirements of the fi re department then the operating characteristics may diff er from the published data in this manual. Repair parts specifi c to each serial number may diff er from those shown in the service procedure. The required parts for each serial number are available on-line by entering www.tft.123456 with the numbers corresponding to the serial number engraved on the product.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev166
4.1 FLOW GRAPHSmeets NFPA flow requirements.
115 PSI
200 GPM
85 PSI
0
10
20
30
40
50
60
70
80
90
100
110
120
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320
Pre
ssur
e (P
SI)
Flow (GPM)
MID-FORCE 100/55 PSI (7/4 BAR)STANDARD 100 PSI LOW 55 PSI NFPA 100 PSI NFPA 55 PSI
70 GPM
STANDARD PRESSURE MODE70 - 200 GPM (265 - 760 L/min)FLOW RANGE
LOW PRESSURE MODE
90 PSI
200 GPM
60 PSI
0
10
20
30
40
50
60
70
80
90
100
110
120
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320
Pre
ssur
e (P
SI)
Flow (GPM)
MID-FORCE 75/45 PSI (5/3 BAR)STANDARD 75PSI LOW 45PSI NFPA 75 PSI NFPA 45 PSI
70 GPM
STANDARD PRESSURE MODE70 - 200 GPM (265 - 760 L/min)FLOW RANGE
LOW PRESSURE MODE
CAFS-Force 1CAFS-FORCE 1 75/45 PSI (5/3 BAR)
0
10
20
30
40
50
60
70
80
90
100
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320
FLOW (GPM)
WATER MODE CAF MODE NFPA 75 PSI
PR
ES
SU
RE
(PS
I)
CAF MODE
WATER MODE
90 PSI
60 PSI
75 GPM
200 GPM
The charts in section 4.2 of this document give specifi c examples of maximum fl ow rates for particular situations. Friction losses may vary due to diff erences in hose construction resulting in fl ows diff erent than those shown. For situations or lengths of hose not listed on the chart, approximate fl ows can be calculated using conventional hydraulics. NOTE: Within the fl ow range, the nozzle inlet pressure may be approximated to be 100 or 75 PSI, when used in the standard pressure mode, and 55 or 45 PSI in low pressure mode.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev167
meets NFPA flow requirements.For Nozzles ManufacturedAfter December 1, 2003
115 PSI
300 GPM
85 PSI
70 PSI
225 GPM
40 PSI
0
10
20
30
40
50
60
70
80
90
100
110
120
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320
Pre
ssur
e (P
SI)
Flow (GPM)
New DUAL-FORCE 100/55 PSI (7/4 BAR) meets NFPA - For Nozzles Manufactured After December 1, 2003
STANDRAD 100 PSI LOW 55 PSI NFPA 100 PSI NFPA 55 PSI
95 GPM
STANDARD PRESSURE MODE95 - 300 GPM (360 - 1150 L/min)FLOW RANGE
LOW PRESSURE MODE95 - 225 GPM (360 - 850 L/min)FLOW RANGE
90 PSI
250 GPM
60 PSI
225 GPM
30 PSI
0
10
20
30
40
50
60
70
80
90
100
110
120
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320
Pre
ssur
e (P
SI)
Flow (GPM)
New DUAL-FORCE 75/45 PSI (5/3 BAR) meets NFPA - For Nozzles Manufactured after December 1, 2003
STANDRAD 75PSI LOW 45PSI NFPA 75 PSI NFPA 45 PSI
95 GPM
STANDARD PRESSURE MODE95 - 250 GPM (360 - 950 L/min)FLOW RANGE
LOW PRESSURE MODE95 - 225 GPM (360 - 850 L/min)FLOW RANGE
CAFS-Force 2
0
10
20
30
40
50
60
70
80
90
100
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320FLOW (GPM)
WATER MODE CAF MODE NFPA 75 PSI
PR
ES
SU
RE
(PS
I)
CAFS-FORCE 2 75/45 PSI (5/3 BAR)
90 PSI
60 PSI
95 GPM
250 GPM
WATER MODE
CAF MODE
FIGURE 3 - NOZZLE PERFORMANCE(on pages 6 - 7)
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev168
4.2 FLOW AND REACTION CHARTS
Flo
w A
nd
No
zzle
Rea
ctio
n C
har
t
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
150
ft.
150
ft.
150
ft.
200
ft.
200
ft.
200
ft.
250
ft.
250
ft.
50 225
200
175
150
125
100
75
21 31 65 93 117
140
162
1838 13 30 45 59 72 84 94
55 93 121
143
163
180
196
209
17 31 42 52 61 69 78 87
21 29 59 84 105
124
141
1587 12 27 40 52 63 73 82
50 83 107
126
143
159
173
186
16 27 36 44 52 59 66 72
21 28 55 77 96 112
128
142
7 12 25 37 47 57 65 73
46 75 97 114
130
143
156
168
14 24 32 39 46 52 58 63
21 32 72 108
141
174
204
---8 14 34 54 72 90 105
---
65 111
143
172
195
213
228
---
21 38 52 65 77 90 102
---
21 32 67 97 125
151
175
1988 14 32 48 63 78 91 102
60 100
129
152
174
192
207
221
19 33 45 56 66 76 86 96
21 31 63 91 114
136
157
1767 13 29 44 57 70 81 91
54 91 117
138
158
175
189
203
17 30 40 50 58 66 75 83
22 36 84 135
196
---
---
---8 15 41 69 101
---
---
---
82 141
184
213
---
---
---
---
27 51 72 90 ---
---
---
---
22 35 79 122
168
212
---
---8 15 38 62 87 109
---
---
75 128
167
198
220
---
---
---
24 45 63 79 95 ---
---
---
113
151
187
222
113
PUMP DISCHARGE PRESSURE (PSI)
1 1/
2" H
OS
E1
3/4"
HO
SE
2" H
OS
E
STD
STD
STD
STD
STD
STD
STD
STD
STD
LPLP
LPLP
LPLP
LPLP
(1) N
umbe
r on
top
in e
ach
box
indi
cate
s flo
w (G
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (L
BS)
. (2)
In S
tand
ard
mod
e, th
e av
erag
e no
zzle
pre
ssur
e is
100
PSI
. (3)
Flo
ws
may
var
y w
ith b
rand
or c
ondi
tion
of h
ose.
(4)
Flow
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W (
GP
M)
RE
AC
TIO
N(L
BS
)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
STD LP
100/
55 P
SI
250
ft.
22 34 75 ---8 15 36 57 78 97 ---
68 119
153
182
205
223
---
---
22 41 56 70 84 98 ---
---
LP
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev169
Flo
w A
nd
No
zzle
Rea
ctio
n C
har
t
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
45M
45M
45M
60M
60M
60M
75M
75M
75M
3.5
15.5
14.0
12.0
10.0
8.6
7.0
5.2
80 115
245
350
445
530
615
695
4 6 14 20 27 33 38 43
210
350
460
540
615
680
740
790
8 14 19 24 28 31 35 40
80 110
225
320
395
470
535
6003 5 12 18 24 29 33 37
190
315
405
475
540
600
655
705
7 12 16 20 24 27 30 33
80 105
210
290
365
425
485
5353 5 11 17 21 26 30 33
175
285
365
430
490
540
590
635
6 11 15 18 21 24 26 29
80 85 275
410
535
660
770
---4 6 15 25 33 41 48 ---
245
420
540
650
740
805
---
---
10 17 24 30 35 41 ---
---
80 120
255
365
475
570
660
7504 6 15 22 29 35 41 46
225
380
490
575
660
725
785
835
9 15 20 25 30 35 39 44
80 115
240
345
430
515
595
665
3 6 13 20 26 32 37 41
205
345
445
520
600
660
715
7708 14 18 23 26 30 34 38
85 135
320
510
740
---
---
---4 175
19 31 46 ---
---
---
310
535
695
805
---
---
---
---
12 23 33 41 ---
---
---
---
85 130
300
460
635
800
---
---4 7 17 28 40 50 ---
---
285
485
630
750
---
---
---
---
11 20 29 36 -- ---
---
---
85 130
285
430
570
710
840
---4 7 16 26 35 44 51 ---
38m
m H
OS
E45
mm
HO
SE
50m
m H
OS
E
7 ba
rLP
LPLP
LPLP
LPLP
LP
(1) N
umbe
r on
top
in e
ach
box
indi
cate
s flo
w (L
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (K
G).
(2) I
n St
anda
rd m
ode,
the
aver
age
nozz
le p
ress
ure
is 7
bar
. (3)
Flo
ws
may
var
y w
ith b
rand
or c
ondi
tion
of h
ose.
(4) F
low
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W (
LPM
)R
EA
CTI
ON
(KG
)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
7 ba
r
LP
7 ba
r7
bar
7 ba
r7
bar
7 ba
r7
bar
7 ba
r7
bar
7/4
BAR
225
450
580
690
775
845
---
---
10 19 25 32 38 45 ---
---
PUMP DISCHARGE PRESSURE (BAR)
LP
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
Flo
w A
nd
No
zzle
Rea
ctio
n C
har
t
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
150
ft.
150
ft.
150
ft.
200
ft.
200
ft.
200
ft.
250
ft.
250
ft.
50 225
200
175
150
125
100
75
PUMP DISCHARGE PRESSURE (PSI)
1 1/
2" H
OS
E1
3/4"
HO
SE
2" H
OS
E
STD
STD
STD
STD
STD
STD
STD
STD
STD
LPLP
LPLP
LPLP
LPLP
(1) N
umbe
r on
top
in e
ach
box
indi
cate
s flo
w (G
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (L
BS)
. (2)
In S
tand
ard
mod
e, th
e av
erag
e no
zzle
pre
ssur
e is
100
PSI
. (3)
Flo
ws
may
var
y w
ith b
rand
or c
ondi
tion
of h
ose.
(4)
FLO
W (
GP
M)
RE
AC
TIO
N(L
BS
)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
STD LP
75/4
5 PS
I
250
ft.
43 55 78 108
136
162
183
204
14 22 35 50 63 73 82 90
69 104
127
149
166
180
192
204
20 32 42 50 60 70 79 89
43 53 72 96 119
138
157
174
14 21 32 43 54 64 72 79
62 92 113
131
148
163
174
184
18 27 35 43 50 57 65 73
42 51 68 86 106
124
140
155
16 24 31 38 44 50 55 62
13 20 29 39 49 57 64 71
45 59 91 134
173
206
220
---
84 121
153
174
191
206
220
---
15 24 41 62 78 91 104
---
25 39 52 65 78 91 104
---
44 57 82 118
148
175
201
214
74 110
136
159
174
189
202
214
15 23 37 54 68 79 88 98
21 34 45 55 66 77 87 98
43 55 77 105
132
155
176
196
67 101
123
145
162
175
188
199
14 22 34 48 60 71 80 86
19 30 40 48 57 66 76 85
45 64 122
203
ó ó ó ó
84 155
182
204
ó ó ó ---
97 140
171
192
210
ó ó ó
45 62 105
166
210
ó ó ó
45 60 97 146
189
215
ó ó
25 53 71 89 ó ó ó ---
15 27 56 89 ó ó ó ---
29 47 63 79 95 ó ó ---
16 26 48 75 95 ó ó ---
15 25 44 67 85 99 ó ---
57 83 103
119
134
147
160
170
LP 89 128
162
181
199
214
ó ó26 42 56 70 85 99 ó ---
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
Flo
w A
nd
No
zzle
Rea
ctio
n C
har
t
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
45M
45M
45M
60M
60M
60M
75M
75M
75M
3.5
15.5
14.0
12.0
10.0
8.6
7.0
5.2
38m
m H
OS
E45
mm
HO
SE
50m
m H
OS
E
5 ba
rLP
LPLP
LPLP
LPLP
LP
(1) N
umbe
r on
top
in e
ach
box
indi
cate
s flo
w (L
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (K
G).
(2) I
n St
anda
rd m
ode,
the
aver
age
nozz
le p
ress
ure
is 7
bar
. (3)
Flo
ws
may
var
y w
ith b
rand
or c
ondi
tion
of h
ose.
(4) F
low
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W (
LPM
)R
EA
CTI
ON
(KG
)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
7 ba
r
LP
5 ba
r5
bar
5 ba
r5
bar
5 ba
r5
bar
5 ba
r5
bar
5/3
BAR
PUMP DISCHARGE PRESSURE (BAR)
LP
261
394
481
564
628
681
727
772
163
208
295
409
515
613
693
7726 10 16 23 29 33 37 41
9 15 19 23 27 32 36 40
163
201
273
363
450
522
594
659
235
348
428
496
560
617
659
696
8 12 16 20 23 26 29 33
6 10 15 20 24 29 33 36
216
314
390
450
507
556
606
643
159
193
257
326
401
469
530
587
7 11 14 17 20 23 25 28
6 9 13 18 22 26 29 32
318
458
579
659
723
780
833
---
170
223
344
507
655
780
833
---
11 18 24 29 35 41 47 ---
7 11 19 28 35 41 47 ---
280
416
515
602
659
715
765
810
167
216
310
447
560
662
761
810
10 15 20 25 30 35 39 44
9 14 18 22 26 30 34 39254
382
466
549
613
662
712
753
163
208
291
397
500
587
666
742
6 10 15 22 27 32 36 39
318
587
689
772
ó ó ó ó
170
242
462
768
ó ó ó ó
11 24 32 40 ó ó ó ---
7 12 25 40 ó ó ó ---
367
530
647
727
795
ó ó ó
170
235
397
628
795
ó ó ó
13 21 29 36 43 ó ó ---
7 12 22 34 43 ó ó ---
337
484
613
685
753
810
ó ó
170
227
367
553
715
814
ó ó
12 19 25 32 39 45 ó ó
7 11 20 30 39 45 ó ---
7 12 19 25 31 36 40 44
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
Flo
w A
nd
No
zzle
Rea
ctio
n C
har
t
150
ft.
150
ft.
150
ft.
200
ft20
0 ft
200
ft25
0 ft
.25
0 ft
.25
0 ft
.
1 1/
2" H
OS
E1
3/4"
HO
SE
2" H
OS
E
50 250
225
200
175
150
125
100
75
PUMP DISCHARGE PRESSURE (PSI)
16 23 33 47 60 72 83 93 102
STD
STD
STD
STD
STD
STD
STD
STD
STD
LPLP
LPLP
LPLP
LPLP
LP
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
(1) N
umbe
r on
top
of e
ach
box
indi
cate
s flo
w (G
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (L
BS)
. (2)
In S
tand
ard
mod
e, th
e av
erag
e no
zzle
pre
ssur
e is
100
P
SI. (
3) F
low
s m
ay v
ary
with
bra
nd o
r con
ditio
n of
hos
e. (
4) F
low
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W(G
PM
)REACTION
(LBS)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
STD LP
48 59 74 100
124
146
165
183
199
54 91 118
141
160
178
194
209
223
47 57 69 89 110
128
145
160
174
50 80 104
124
141
157
171
184
196
45 56 65 82 100
116
131
144
157
47 72 94 112
128
142
154
166
177
17 31 41 51 60 68 76 84 91
15 22 30 42 53 63 72 80 88
15 27 36 44 51 58 64 71 77
14 21 28 38 47 56 64 71 81
15 23 33 46 59 71 81 91 100
50 61 83 119
151
179
204
227
248
62 110
144
172
196
217
237
255
269
49 60 77 107
134
158
179
199
216
56 98 128
152
174
193
210
226
241
48 59 73 98 122
143
162
179
195
50 61 86 126
160
190
217
242
264
17 25 38 58 75 91 105
117
129
14 24 32 39 45 51 57 62 67
20 38 52 65 77 88 99 110
122
16 24 35 51 66 79 91 101
112
18 33 45 56 66 75 84 93 102
17 25 40 61 80 97 112
126
139
53 89 116
138
157
175
190
205
218
51 63 99 152
198
238
273
307
329
76 141
185
221
252
274
294
311
328
51 62 91 136
176
210
240
268
293
70 127
166
199
227
251
270
287
303
65 116
152
182
208
230
250
268
283
17 30 40 50 58 66 74 81 89
18 27 47 76 101
124
144
163
181
25 51 71 90 108
126
144
163
181
17 26 43 67 89 108
125
141
155
23 45 62 78 93 108
123
138
154
21 40 56 70 80 95 108
121
134
150
ft.
200
ft25
0 ft
.2
1/2"
HO
SE
STD
STD
STD
LPLP
LP
53 65 122
207
283
331
---
---
---
19 28 59 106
149
183
---
---
---
53 65 135
245
328
---
---
---
---
107
206
265
299
326
---
---
---
---
53 65 128
223
312
340
---
---
---
102
194
254
288
315
340
---
---
---
97 184
242
279
306
329
---
---
---
19 28 66 128
179
---
---
---
---
37 82 119
149
179
---
---
---
---
19 28 62 115
166
195
---
---
---
35 76 110
139
167
195
---
---
---
33 71 103
130
156
182
---
---
---
100/
55 P
SI
For
No
zzle
s w
ith:
Ser
ial #
TF
T-H
4651
01 a
nd o
ver
or
Man
ufac
ture
d a
fter
12/
01/2
003
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
For
No
zzle
s w
ith:
Ser
ial #
TF
T-H
4651
01 a
nd o
ver
or
Man
ufac
ture
d a
fter
12/
01/2
003
45M
45M
45M
60M
60M
60M
75M
75M
75M
38m
m H
OS
E45
mm
HO
SE
50m
m H
OS
E
3.5
17.0
15.5
14.0
12.0
10.0
8.6
7.0
5.2
PUMP DISCHARGE PRESSURE (bar)
7 10 15 21 27 33 38 42 46
7 ba
rLP
LPLP
LPLP
LPLP
LPLP
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
(1) N
umbe
r on
top
of e
ach
box
indi
cate
s flo
w (G
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (L
BS)
. (2)
In S
tand
ard
mod
e, th
e av
erag
e no
zzle
pre
ssur
e is
100
P
SI. (
3) F
low
s m
ay v
ary
with
bra
nd o
r con
ditio
n of
hos
e. (
4) F
low
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W(l
/min
)R
EA
CTI
ON
(KG
)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
7 ba
r
LP
182
223
280
379
469
553
625
693
753
204
344
447
534
606
674
734
791
844
178
216
261
337
416
484
549
606
659
189
303
394
469
534
594
647
696
742
170
212
246
310
379
439
496
545
594
178
273
356
424
484
537
583
628
670
8 14 19 23 27 31 34 38 41
7 10 14 19 24 29 33 36 40
7 12 16 20 23 26 29 32 35
6 10 13 17 21 25 29 32 35
7 10 15 21 27 32 37 41 45
189
231
314
450
572
678
772
859
939
235
416
545
651
742
821
897
965
1018
185
227
291
405
507
598
678
753
818
212
371
484
575
659
731
795
855
912
182
223
276
371
462
541
613
678
738
189
231
326
477
606
719
821
916
999
8 11 17 26 34 41 48 53 59
6 11 15 18 20 23 26 28 30
9 17 24 29 35 40 45 50 55
7 11 16 23 30 36 41 46 51
8 15 20 25 30 34 38 42 46
8 11 18 28 36 44 51 57 63
201
337
439
522
594
662
719
776
825
193
238
375
575
749
901
1033
1162
1245
288
534
700
836
954
1037
1113
1177
1241
193
235
344
515
666
795
908
1014
1109
265
481
628
753
859
950
1022
1086
1147
246
439
575
689
787
871
946
1014
1071
8 14 18 23 26 30 34 37 40
8 12 21 34 46 56 65 74 82
11 23 32 41 49 57 65 74 82
8 12 20 30 40 49 57 64 70
10 20 28 35 42 49 56 63 70
10 18 25 32 38 43 49 55 61
45M
60M
75M
64m
m H
OS
E
LPLP
LP
201
246
462
783
1071
1253 ó ó ---9 13 27 48 68 83 ó ó ---
201
246
511
927
1241 ó ó ó ó
405
780
1003
1132
1234 ó ó ó ---
201
246
484
844
1181
1287 ---
ó ---
386
734
961
1090
1192
1287 ó ó ó
367
696
916
1056
1158
1245 ó ó ---
9 13 30 58 81 ó ó ó ---
17 37 54 68 81 ó ó ó ---
9 13 28 52 75 88 ó ó ---
16 34 50 63 76 88 ó ó ---
15 32 47 59 71 83 ó ó ---
7 ba
r7
bar
7 ba
r7
bar
7 ba
r7
bar
7 ba
r7
bar
7 ba
r7
bar
7 ba
r
7/4
BA
RFl
ow
An
d N
ozz
le R
eact
ion
Ch
art
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
Flo
w A
nd
No
zzle
Rea
ctio
n C
har
t
150
ft.
150
ft.
150
ft.
200
ft20
0 ft
200
ft25
0 ft
.25
0 ft
.25
0 ft
.
1 1/
2" H
OS
E1
3/4"
HO
SE
2" H
OS
E
50 250
225
200
175
150
125
100
75
PUMP DISCHARGE PRESSURE (PSI)
16 25 39 52 63 72 81 89 97STD
STD
STD
STD
STD
STD
STD
STD
STD
LPLP
LPLP
LPLP
LPLP
LP
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
(1) N
umbe
r on
top
of e
ach
box
indi
cate
s flo
w (G
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (L
BS)
. (2)
In S
tand
ard
mod
e, th
e av
erag
e no
zzle
pre
ssur
e is
100
P
SI. (
3) F
low
s m
ay v
ary
with
bra
nd o
r con
ditio
n of
hos
e. (
4) F
low
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W(G
PM
)R
EA
CTI
ON
(LB
S)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
STD LP
48 64 96 122
145
165
183
200
216
71 104
130
151
170
187
202
216
229
47 60 85 108
124
144
160
174
188
65 91 114
133
149
164
178
190
202
45 58 77 98 115
130
144
157
169
60 82 103
120
135
148
160
172
182
20 31 41 49 57 65 72 80 88
15 23 34 45 54 62 70 77 83
18 27 35 42 48 55 61 66 72
14 22 31 40 48 56 62 68 74
15 25 38 50 61 70 79 87 94
50 73 115
149
177
203
227
249
269
84 126
157
183
206
225
241
257
271
49 67 103
131
156
178
198
216
234
75 112
139
162
182
201
217
231
244
48 63 93 119
141
160
178
195
210
50 76 121
158
189
217
243
266
284
17 29 48 64 78 91 102
113
123
16 24 31 37 43 48 53 58 63
25 39 52 63 74 86 98 109
122
16 26 42 56 68 79 88 97 106
22 34 44 54 63 71 80 90 99
17 31 51 69 84 98 110
121
133
70 101
126
147
165
182
197
211
223
51 88 148
197
239
276
295
312
329
107
162
203
232
256
276
295
313
336
51 81 132
173
210
242
270
289
304
96 145
182
212
234
255
272
288
304
88 133
166
194
218
236
254
269
284
20 30 39 48 55 63 70 77 85
18 36 64 88 108
127
145
163
181
33 54 72 90 108
127
145
163
180
17 33 57 76 94 109
123
138
154
29 47 63 77 92 108
123
138
154
26 42 56 68 81 94 107
120
134
150
ft.
200
ft25
0 ft
.2
1/2"
HO
SE
STD
STD
STD
LPLP
LP
53 111
206
282
307
343
356
368
380
18 46 92 131
157
186
210
232
255
53 123
252
300
343
356
369
ó ---
157
230
269
300
341
355
368
ó ---
53 116
224
290
317
349
362
375
ó
148
221
260
290
335
348
361
373
ó
140
212
251
281
307
342
354
367
378
19 52 114
150
185
210
235
ó ---
52 89 120
150
185
209
234
ó ---
19 49 101
140
167
198
222
245
---
48 83 112
140
173
197
221
245
---
45 77 105
131
157
186
209
232
255
75/4
5 P
SI
For
No
zzle
s w
ith:
Ser
ial #
TF
T-H
4651
01 a
nd o
ver
or
Man
ufac
ture
d a
fter
12/
01/2
003
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
For
No
zzle
s w
ith:
Ser
ial #
TF
T-H
4651
01 a
nd o
ver
or
Man
ufac
ture
d a
fter
12/
01/2
003
45M
45M
45M
60M
60M
60M
75M
75M
75M
38m
m H
OS
E45
mm
HO
SE
50m
m H
OS
E
3.5
17.0
15.5
14.0
12.0
10.0
8.6
7.0
5.2
PUMP DISCHARGE PRESSURE (bar)
7 11 18 24 29 33 37 40 44
5 ba
rLP
LPLP
LPLP
LPLP
LPLP
CA
UT
ION
: C
ha
ng
ing
to
Lo
w P
ress
ure
mo
de
wil
l ty
pic
all
y in
cre
ase
no
zzle
re
ac
tio
n.
(1) N
umbe
r on
top
of e
ach
box
indi
cate
s flo
w (G
PM
), a
nd n
umbe
r on
botto
m in
dica
tes
nozz
le re
actio
n (L
BS)
. (2)
In S
tand
ard
mod
e, th
e av
erag
e no
zzle
pre
ssur
e is
100
P
SI. (
3) F
low
s m
ay v
ary
with
bra
nd o
r con
ditio
n of
hos
e. (
4) F
low
s ar
e ap
prox
imat
e an
d do
not
refle
ct lo
sses
in p
reco
nnec
t pip
ing.
FLO
W(l
/min
)R
EA
CTI
ON
(KG
)
= S
TAN
DA
RD
PR
ES
SU
RE
MO
DE
= L
OW
PR
ES
SU
RE
MO
DE
7 ba
r
LP
182
242
363
462
549
625
693
757
818
269
394
492
572
643
708
765
818
867
178
227
322
409
481
545
606
659
712
246
344
431
503
564
621
674
719
765
170
220
291
371
435
492
545
594
640
227
310
390
454
511
560
606
651
689
8 14 19 23 27 31 34 38 41
7 10 15 20 24 28 32 35 38
8 12 16 19 22 25 28 30 33
6 10 14 18 22 25 28 31 34
7 11 17 23 28 32 36 39 43
189
276
435
564
670
768
859
942
1018
318
477
594
693
780
852
912
973
1026
185
254
390
496
590
674
749
818
886
284
424
526
613
689
761
821
874
924
182
238
352
450
534
606
674
738
795
189
288
458
598
715
821
920
1007
1075
8 13 22 29 35 41 46 51 56
7 11 14 17 20 22 24 26 29
11 18 24 29 34 39 44 49 55
7 12 19 25 31 36 40 44 48
10 15 20 24 29 32 36 41 45
8 14 23 31 38 44 50 55 60
265
382
477
556
625
689
746
799
844
193
333
560
746
905
1045
1117
1181
1245
405
613
768
878
969
1045
1117
1185
1272
193
307
500
655
795
916
1022
1094
1151
363
549
689
802
886
965
1030
1090
1151
333
503
628
734
825
893
961
1018
1075
9 14 18 22 25 29 32 35 39
8 16 29 40 49 58 66 74 82
15 24 33 41 49 58 66 74 82
8 15 26 34 43 49 56 63 70
13 21 29 35 42 49 56 63 70
45M
60M
75M
64m
m H
OS
E
LPLP
LP
201
420
780
1067
1162
1298
1347
1393
14388 21 42 59 71 84 95 105
116
201
466
954
1136
1298
1347
1397 ó ó
594
871
1018
1136
1291
1344
1393 ó ---
201
439
848
1098
1200
1321
1370
1419 ---
560
836
984
1098
1268
1317
1366
1412 ó
530
802
950
1064
1162
1294
1340
1389
1431
9 24 52 68 84 95 107
ó ---
24 40 54 68 84 95 106
ó ---
9 22 46 64 76 90 101
111
---
22 38 51 64 78 89 100
111
---
20 35 48 59 71 84 95 105
116
5 ba
r5
bar
5 ba
r5
bar
5 ba
r5
bar
5 ba
r5
bar
5 ba
r7
bar
5 ba
r
5/3
BA
RFl
ow
An
d N
ozz
le R
eact
ion
Ch
art
12 19 25 31 37 43 49 54 61
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1616
4.3 REACH AND TRAJECTORYCare must be taken to avoid dents or nicks in the nozzle tip because they can seriously aff ect the stream reach.The following are specifi c examples of maximum fl ow rates for particular situations. Friction losses may vary due to diff erences in hose construction resulting in fl ows diff erent than those shown. For situations or lengths of hose not listed on the chart, approximate fl ows can be calculated using conventional hydraulics.All reach testing was taken in still air conditions at an elevation of 30 degrees.
MID-FORCEFlow range 70-200 GPM, automatic pressure control at emergency low pressure mode.
NOZZLE TESTEDMid-Force
Model: HM-VPGISerial #: TFTH-145249
MODELHD-VPGISHOWN
DUAL-FORCEFlow range 70-250 GPM, automatic pressure control with 100 PSI and emergency low pressure mode.
NOZZLE TESTEDDUAL-FORCE
Model: HD-VPGISerial #: TFTH-041501
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1617
5.0 NOZZLE CONTROLSNozzle control valves must be opened slowly to eliminate unnecessary strain on the hose and couplings and reduce pressure surges.
5.1 FLOW CONTROL5.1.1 LEVER TYPE FLOW CONTROLOn models that use a lever type valve handle, the nozzle is shut off when the handle is fully forward. The valve handle has detented fl ow positions. These detent positions allow the nozzle operator to regulate the fl ow of the nozzle depending on the need or what can be safely and eff ectively handled. TFT recommends the use of a pistol grip for easier handling. For additional stress reduction, a hose rope or strap may also be used. This permits more eff ective use and ease of advancement, while minimizing strain and fatigue.Nozzles attached to an in-service hose shall be stored in the off position.
5.1.2 TIP ONLYTip only nozzles have NO shut-off valve within the nozzle and MUST be used with a separate ball valve attached to the nozzle. Using a nozzle without a shutoff is an unsafe practice and should never be done.
5.1.3 BALL SHUT-OFFA separate ball valve for use with Tip Only nozzles is shut off when the valve handle is fully forward. Pulling back on the handle opens the valve. Open valve slowly to avoid sudden changes in nozzle reaction. Close valve slowly to prevent water hammer. Note: In partially open positions a ball valve will cause turbulence and adversely aff ect stream quality. Nozzles attached to an in-service hose shall be stored in the off position.
5.1.4 TWIST SHUT-OFFOn models that use a twist fl ow control, the valve is opened or closed by rotating the valve ring. Rotating the ring clockwise (as seen from the operating position behind the nozzle) closes the valve, while counterclockwise rotation opens it. Detents are provided at four intermediate positions and the position of the valve is shown by the exposed valve position label. Nozzles attached to an in-service hose shall be stored in the off position.
5.1.5 IMPULSE TRIGGER FLOW CONTROL
NOTE: THE TRIGGER RETURNS TO OFF IF NOT HELD OR LOCKED
OFFON
TRIGGER
LOCK
WARNINGDo not intentionally release the nozzle while fl owing and trust the valve to shut off automatically. The trigger nozzle’s ability to shut off by itself represents an extra level of safety when following normal nozzle handling procedures. To rely on it as the sole means of safety increases the risk of injury from an out of control nozzle. Release nozzle when fl ow has stopped.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1618
5.1.5.2 TRIGGER FLOW CONTROL SPEED ADJUSTMENTThe IMPULSE valve contains a slow close mechanism to prevent the nozzle from slamming off if the trigger is suddenly released. The closing speed is set at the factory to be slow enough to reduce water hammer, (“water hammer” is always present in any valve when it is shut off . The slow close mechanism will reduce this but cannot eliminate it completely) but fast enough to reduce the potential danger of hose whipping from a dropped nozzle. The closing speed may be adjusted as shown in the fi gure.5.1.5.2.
SlowerClose
FasterClose
Do not unscrew the adjuster past the end of the hand grip (to unscrew it too far could result in the loss of dampening fl uid.)
WARNINGAs the closing time is increased so does the risk of injury from an out of control nozzle. A fl owing nozzle can cause injury within the fi rst second of lost control. Use caution when adjusting the closing speed and always verify performance after adjustment.
5.1.5.1 IMPULSE TRIGGER LOCK
Use an 1/8” (3mm) punch to push out pin and remove lock if the lock is not desired.
LOCK
TRIGGER
LOCK PIVOT PIN
To Lock: Push on the lock while pulling back the trigger to engage one of the four locked positions.
To Release: Pull back slightly on trigger without any pressure on the lock. The spring loaded lock will automatically move to the unlocked position.
WARNINGWhen the trigger lock is engaged, the nozzle will not shut off if dropped. Always shut off nozzle before releasing the pistol grip to avoid injury from an out of control nozzle.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1619
5.2 PATTERN AND FLUSH CONTROL5.2.1 PATTERN CONTROLTFT’s nozzles have full pattern control from straight stream to wide fog. Turning the stream shaper clockwise (as seen from the operating position behind the nozzle) moves the shaper to the straight stream position. Turning the shaper counterclockwise will result in an increasingly wider pattern.Since the stream trim point varies with fl ow, the stream should be “trimmed” after changing the fl ow to obtain the straightest and farthest reaching stream. To properly trim the stream, fi rst open the pattern to narrow fog. Then close the stream to parallel to give maximum reach. Note: Turning the shaper further forward will cause stream crossover and reduce the eff ective reach of the nozzle.The nozzle reaction is greatest when the shaper is in the straight stream position. The nozzle operator must be prepared for a change in reaction as the pattern is changed.
5.1.5.3 NORMAL OPERATING POSITION
45°
15°
90°
45°
Horizontal
Slow Closer Operating Range
Slow Closer Operating Range
WARNINGThe Slow Close Feature relies on a fl uid and air combination in the pistol grip. For proper function, the pistol grip should be within its normal operating position. The normal operating position is with the nozzle horizontal or pointing up with the pistol grip within 45 degrees of vertical. Releasing the trigger suddenly outside of the normal orientation will likely result in faster shut-off causing a higher pressure spike and increasing the risk of a burst hose. Do not suddenly release the trigger when operating outside of the nozzle’s normal orientation.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1620
5.2.2 FLUSH CONTROLSmall debris passes through the debris screen (if equipped) and may get caught inside the nozzle. This trapped material will cause poor stream quality, shortened reach, and reduced fl ow. To remove small debris, the nozzle may be fl ushed as follows:
• While still fl owing water, rotate the SHAPER counterclockwise (as viewed from behind the nozzle) to the fl ush position. (increased resistance will be felt on the SHAPER or RING as the nozzle goes into fl ush) This will open the nozzle allowing debris to pass through.
• During fl ush the nozzle reaction will decrease as the pattern becomes wider and the pressure drops. The nozzle operator must be prepared for an increase of nozzle reaction when returning the nozzle from the fl ush position to retain control of the nozzle.
• Rotate the SHAPER out of fl ush to continue normal operations.
WARNINGLarge amounts or pieces of debris may be unfl ushable and can reduce the fl ow of the nozzle resulting in an ineff ective fl ow. In the event of a blockage, it may be necessary to retreat to a safe area, uncouple the nozzle and remove debris.
5.3 STANDARD/LOW PRESSURE KNOB MID-FORCE & DUAL-FORCEFor situations where the standard pressure setting at the nozzle is impractical, the MID-FORCE or DUAL-FORCE may be switched to a low pressure mode. In the low pressure mode the nozzle pressure is reduced by about 50% while maintaining a usable stream and increasing the fl ow. The nozzle operator must be prepared for a change in reaction when changing modes. See the fl ow chart in section 4.2 for actual performance.To switch to the low pressure mode, shut off water fl ow with valve and turn knob at front of nozzle (see fi gure 4) counterclockwise (when viewed from front). Reopen valve to fl ow water at reduced pressure. Repeat the process, except turn knob clockwise, to return to standard pressure operation
Knob InLow Pressure Mode
Knob InStandard Operating Mode
Mid-ForceDual-Force
Mid-ForceDual-Force
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1621
6.0 USE WITH FOAMThe nozzle may be used with foam solutions. Refer to fi re service training for the proper use of foam.
WARNINGFor Class B fi res, lack of foam or interruption in the foam stream can cause a break in the foam blanket and greatly increase the risk of injury or death. Assure that:
• Application rate is suffi cient (see NFPA 11 or foam manufacturer’s recommendations)• Enough concentrate is on hand to complete task (see NFPA for minimum duration time
requirements)• Foam logistics have been carefully planned. Allow for such things as:• Storage of foam in a location not exposed to the hazard it protects• Personnel, equipment and technique to deliver foam at a rapid enough rate• Removal of empty foam containers • Clear path to deliver foam, as hoses and other equipment and vehicles are deployed
WARNINGImproper use of foam can result in injury or damage to the environment. Follow foam manufacturer’s instructions and fi re service training to avoid:
• Using wrong type of foam on a fi re, i.e. Class A foam on a Class B fi re• Plunging foam into pools of burning liquid fuels• Causing environmental damage• Directing stream at personnel
WARNINGThere are a wide variety of foam concentrates. Each user is responsible for verifying that any foam concentrate chosen to be used with this unit has been tested to assure that the foam obtained is suitable for the purpose intended.
WARNINGUse of compressed air foam (CAF) with hand held nozzles can cause sudden surges in nozzle reaction force resulting in risk of injury or death from loss of footing or hose whipping. Be prepared for sudden changes in nozzle reaction caused by:
• Slug loading (Loss of foam concentrate sends slugs of air and water into the nozzle)• Sudden release of built-up pressure in the hose when opening a nozzle
6.1 FOAM ASPIRATING ATTACHMENTSMulti-expansion or low expansion aspirating attachments may be used with nozzles to increase the expansion ratio. These foam tubes attach and detach quickly from the nozzle. As expansion ratio is increased, the reach of the nozzle will be decreased due to the greater amount of bubbles in the stream and their ability to penetrate the air. Generally the straight stream reach with foam is approximately 10% less than with water only. Actual results will vary based on brand of foam, hardness of water, temperature, etc. For specifi c information, see LIA-025 (MANUAL: Foam Attachments for TFT Nozzles).
7.0 USE OF NOZZLES7.1 MID-FORCE AND DUAL-FORCE NOZZLESMany factors contribute to the extinguishment of a fi re. Among the most important is delivering water at a fl ow rate suffi cient to absorb heat faster than it is being generated. The fl ow rate depends largely on the pump discharge pressure and hose friction loss. It can be calculated using a hydraulic equation such as:
PDP = NP + FL + DL + EL
PDP = Pump discharge pressure in PSINP = Nozzle pressure in PSIFL = Hose friction loss in PSIDL = Device loss in PSIEL = Elevation loss in PSI
This manual is not intended to act as a training guide for safe fi reground tactics and operations. For additional information visit www/tft.com or contact customer service at 800-348-2686.IT IS THE RESPONSIBILITY OF THE INDIVIDUAL FIRE DEPARTMENT OR AGENCY TO DETERMINE PHYSICAL CAPABILITIES AND SUITABILITY FOR AN INDIVIDUAL’S USE OF THIS EQUIPMENT.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1622
7.2 CAFS-FORCE 1 AND CAFS-FORCE 2 NOZZLESThe CAFS-FORCE 1 and CAFS-FORCE 2 nozzles are optimized for use with compressed air foam systems, CAFS. They have a streamlined fl ow path with no gasket grabber. The CAFS-FORCE nozzles have two settings: Standard pressure/Water and Low Pressure/CAFS. The CAFS-FORCE tip can be removed to use the valve as a smoothbore. See Section 4.0 Flow Characteristics for CAFS-FORCE Nozzle fl ow characteristics.Hose handling techniques with compressed air foam (CAF) diff er considerably from liquid fi lled hoses as a result of the added energy stored by pressurized air. The authority having jurisdiction must establish safe CAF operational procedures and insure appropriate training.
Knob In Low Pressure CAFS Mode
Knob In Standard Pressure Water Mode
CAFS-Force1CAFS-Force2
CAFS-Force1CAFS-Force2
WARNINGUse of compressed air foam (CAF) with hand held nozzles can cause sudden surges in nozzle reaction force resulting in risk of injury or death from loss of footing or hose whipping. Be prepared for sudden changes in nozzle reaction caused by:Slug loading (Loss of foam concentrate sends slugs of air and water into the nozzle) Sudden release of built-up pressure in the hose when opening a nozzle
8.0 APPROVALS Many nozzle confi gurations carry the FM Approval rating, NFPA certifi cation, or EN certifi cation.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1623
9.0 COLOR CODED VALVE HANDLE AND PISTOL GRIPThe TFT nozzle with lever type valve handles are supplied with black valve handle covers and pistol grips. The handle covers and pistol grips are available from TFT in various colors for those departments wishing to color code the nozzle to the discharge controls. A colored handle cover set will be sent upon receipt of the warranty card by TFT. Your department’s name can also be engraved on the covers (see warranty card for more information).Handle covers are replaceable by removing the four screws that hold the handle covers in place. Use a 3/32” Allen wrench when replacing screws. Pistol grip is replaceable by following TFT instruction sheet LTT-108 for standard grips or LTT-115 for Trigger Controlled Valves.For standardization NFPA 1901 (A-4-9.3) recommends the following color code scheme:
Preconnect #1 or Bumper Jump LinePreconnect or discharge #2 Preconnect or discharge #3 Preconnect or discharge #4 Preconnect or discharge #5 Preconnect or discharge #6 Preconnect or discharge #7 Foam Lines
OrangeRedYellowWhiteBlueBlackGreenRed w/ White border (Red/White)
Other Colors Available:
• Gray• Pink• Purple• Tan
9.1 IMPULSE TRIGGER VALVE SYSTEM NOZZLE COLORED PISTOL GRIPSThe TFT Impulse Trigger Valve System nozzles are supplied with black pistol grip covers. The pistol grip covers are available from TFT in various colors for those departments wishing to color code the nozzle to the discharge controls. Follow the steps below to change the pistol grip cover.
Pistol Grip Cover(TN691-BLK)
Cap (TN103)(1/2 in square drive)
Adjusting Screw (TN102)(3/16 in Allen Wrench)
1) Orient nozzle vertically. This keeps the dampening fl uid in the pistol grip from spilling out.
2) Remove the Cap. (1/2 in square drive) The Adjusting Screw (3/16 in Allen Wrench) may need to be turned in or removed to be able to engage the square pocket in the cap. Note the position of the Adjusting Screw before moving it.
3) Slide off the Pistol Grip Cover and install a new one. Be sure the Pistol Grip Cover’s internal rib is toward the back of the nozzle.
4) Reinstall the Cap until it bottoms out on its shoulder.5) Reinstall or reposition the Adjusting Screw if it has been
moved from its original location.6) Flow nozzle to check performance of slow closer. Adjust as
needed (see section 5.1.5.2).
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1624
10.0 WARRANTYTask Force Tips, Inc., 3701 Innovation Way, Valparaiso, Indiana 46383-9327 (“TFT”) warrants to the original purchaser of its nozzles and other equipment (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects in material and workmanship during the fi ve (5) year period from the date of purchase.TFT’s obligation under this warranty is specifi cally limited to replacing or repairing the equipment (or its parts) which are shown by TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327, within a reasonable time after discovery of the defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will correct the problem within a reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is an intended or unintended benefi ciary of the equipment, shall not be entitled to recover from TFT any consequential or incidental damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone else.THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE. THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.This limited warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1625
11.0 MAINTENANCETFT nozzles are designed and manufactured to be damage resistant and require minimal maintenance. However, as the primary fi refi ghting tool upon which your life depends, it should be treated accordingly. Do not drop or throw equipment.
11.1 FIELD LUBRICATIONAll Task Force Tip nozzles are factory lubricated with high quality silicone grease. This lubricant has excellent washout resistance and long term performance. If your department has unusually hard or sandy water, the moving parts may be aff ected. Foam agents and water additives contain soaps and chemicals that may break down the factory lubrication. The moving parts of the nozzle should be checked on a regular basis for smooth and free operation, and signs of damage. IF THE NOZZLE IS OPERATING CORRECTLY, THEN NO ADDITIONAL LUBRICATION IS NEEDED. Any nozzle that is not operating correctly should be immediately removed from service. The fi eld use of Break Free CLP (spray or liquid) lubricant will help to restore the smooth and free operation of the nozzle. However, these lubricants do not have the washout resistance and long-term performance of the silicone grease. Therefore, re-application of Break Free CLP will be needed on a regular basis. CAUTION: Aerosol lubricants contain solvents that can swell O-Rings if applied in excess. The swelling can inhibit smooth operation of the moving parts. When used in moderation, as directed, the solvents quickly evaporate without adversely swelling the O-Rings. The nozzle can be returned to the factory for a complete checkup and re-lubrication with silicone grease
PART ONE — COUPLING DOWNPosition the nozzle at a 45-degree angle with the COUPLING end down. CLOSE the valve handle and set the pattern to STRAIGHT STREAM. Then spray a short burst into these areas: #1 FRONT PATTERN CONTROL SEAL Spray in between the pattern control and the barrel.#2 PRESSURE CONTROL UNITPlace check sticks behind baffl e while shaper is in fl ush. Cycle baffl e in and out using check sticks several times to work lubrication into o-rings. #3 FRONT SLIDER SEALa) Rotate shaper into FLUSH position.b) Spray down the front end of the nozzle to dribble lubricant into the clearances between the shaper and the valve body.
While holding nozzle at the angle, wait 30 seconds for the lubricant to penetrate into the clearances. Cycle the valve handle and rotate the shaper from straight stream to full fl ush several times, and then proceed to the next section.
PART TWO — COUPLING UPPosition the nozzle at a 45-degree angle with the BUMPER end down. OPEN the valve handle and set the pattern to FLUSH. Spray a short burst in these areas: #4 REAR SHAPER SEAL Spray down the clearance between the label and the shaper guide.#5 REAR SLIDER SEAL Spray into the clearance between the slider and the valve body.#6 FLUSH MECHANISM SEALa) With the handle on the top, spray down into the nozzle. The aerosol extension tip will help direct the spray into clearances leading to the O-Ring.b) Rotate nozzle so the valve is on the bottom and spray another short burst.#7 DETENTS IN THE HANDLE Spray a small amount on the detent followers located in the handle.
While holding nozzle at the angle, wait 30 seconds, then cycle the valve handle several times. Rotate the pattern control from straight stream to full fl ush several times. The pattern control should move freely and easily. The barrel cone should move forward to within 1/16” of the baffl e before the shaper reaches straight stream position. Wipe off excess lubricant.IF THIS PROCEDURE DOES NOT RESTORE SMOOTH AND FREE OPERATION OF ALL THE MOVING PARTS,
THEN FACTORY SERVICE IS NEEDED. • 24-HOUR HOT LINE — 800-348-2686 • www.tft.com
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1626
11.2 IMPULSE TRIGGER VALVE LUBRICATION1) Insert tube from BreakFree into drain
hole in pistol grip.
2) With nozzle upside down spray a 2 second burst into the pistol grip.Holding a rag around the tube here can help keep excess BreakFree from the outside of the nozzle.
3) Keep nozzle upside down for at least 10 seconds to allow the BreakFree to fl ow into the valve area.
4) Check for smooth and free operation of the trigger. Repeat a second time if needed.
Holding a rag around the tube herecan help keep excess BreakFreefrom the outside of the nozzle.
If this procedure does not restore trigger operation then factory service is needed. 24 hour Technical Service and Support - 800-348-2686 - www.tft.com
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev1627
11.3 SERVICE TESTINGIn accordance with NFPA 1962 (2013), nozzles must be tested a minimum of annually. Nozzles failing any part of this test must be removed from service, repaired and retested upon completion of the repair.
11.3.1 HYDROSTATIC TESTINGEach nozzle with a shut off mechanism shall be tested in the following manner.
1. The nozzle shall be placed in a device capable of holding it and the shut off shall be closed.2. A device capable of exerting a hydrostatic pressure of 300 psi (2070 kPa) or 1.5 times the maximum operating pressure,
whichever is higher, shall be attached to the nozzle.3. All air shall be bled from the system.4. The gage pressure shall be increased by 50 psi (3.5 bar or 345 kPa) increments, held for 30 seconds at each pressure up to
the maximum pressure for which the nozzle is being tested, and then held for one minute without leakage.5. There shall be no sign of leakage through the valve or shut off .
11.3.2 FLOW TESTINGFlow testing must be conducted in the following manner.
1. The nozzle shall be mounted so that the fl ow rate and pressure through the nozzle and the pressure at the inlet can be accurately measured.
2. With the shut off fully open, the inlet pressure shall be adjusted to the rated pressure ±2 percent.3. The valve or shut off and pattern controls shall be operated through their full range of motion at 100 psi (6.9 bar or 690 kPa)
with no signs of leaking, binding or other problems.4. Evaluate the fl ow of nozzles as defi ned by NFPA 1964 in the following manner:
Automatic (Constant Pressure) Spray Nozzles1. The fl ow rate shall slowly be increased to the maximum rated fl ow, and the minimum and maximum pressures through
the fl ow range recorded.2. Nozzles shall maintain their rated pressure ±15 psi (±1 bar or ±100 kPa) throughout the rated fl ow range.
11.3.3 RECORDSA record of testing and repairs must be maintained from the time the nozzle is purchased until it is discarded. Each TFT nozzle is engraved with a unique serial number which, if so desired, can be used to identify nozzle for documentation purposes.The following information, if applicable, must be included on the test record for each nozzle:
1. Assigned identifi cation number2. Manufacturer3. Product or model designation4. Vendor5. Warranty6. Hose connection size7. Maximum operating pressure8. Flow rate or range9. Date received and date put in service10. Date of each service test and service test results11. Damage and repairs, including who made the repairs and the cost of repair parts12. Reason removed from service
NFPA 1962: Standard for the care, use, inspection, service testing, and replacement of fi re hose, couplings, nozzles and fi re hose appliances. (2013 ed., Section 5.5.4). Quincy, MA: National Fire Protection Agency.
©Copyright Task Force Tips, Inc. 2002 - 2015 LIN-035 July 16, 2015 Rev16
TASK FORCE TIPS, INC.MADE IN USA • www.tft.com
3701 Innovation Way, Valparaiso, IN 46383-9327 USA800-348-2686 • 219- 462-6161 • Fax 219-464-7155
12.0 OPERATION AND INSPECTION CHECKLISTBEFORE EACH USE the nozzle must be inspected to this checklist:
1) There is no obvious damage such as missing, broken or loose parts, damaged labels etc.2) Debris screen is free of debris3) Coupling is tight and leak free4) Valve operates freely through full range and regulates fl ow5) “OFF” position does fully shut off and fl ow is stopped6) Nozzle fl ow is adequate as indicated by pump pressure and nozzle reaction7) Shaper turns freely and adjusts pattern through full range8) Shaper turns into full fl ush and out of fl ush with normal fl ow and pressure restored9) Shaper detent (if so equipped) operates smoothly and positively.
BEFORE BEING PLACED BACK IN SERVICE, nozzles must be inspected to this checklist;1) All controls and adjustments are operational2) Shut off valve (if so equipped) closes off the fl ow completely3) There are no broken or missing parts4) There is no damage to the nozzle that could impair safe operation (e.g. dents, cracks, corrosion or other defects)5) The thread gasket is in good condition6) The waterway is clear of obstructions7) Nozzle is clean and markings are legible8) Coupling is retightened properly9) Shaper is set to desired pattern10) Shutoff handle is stored in the OFF position
NFPA 1962: Standard for the care, use, inspection, service testing, and replacement of fi re hose, couplings, nozzles and fi re hose appliances. (2013 ed., Section 5.2.2). Quincy, MA: National Fire Protection Agency.
WARNINGAny nozzle failing any part of the checklist is unsafe for use and must have the problem corrected before use or being placed back into service. Operating a nozzle that has failed the checklist is a misuse of this equipment.
11.4 REPAIRFactory service is available with repair time seldom exceeding one day in our facility. Factory-serviced nozzles are repaired by experienced technicians, wet tested to original specifi cations, and promptly returned. Repair charges for non-warranty items are minimal. Any returns should include a note as to the nature of the problem and whom to reach in case of questions.Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability for damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at www.tft.com for parts lists, exploded views, test procedures and troubleshooting guides.Performance tests shall be conducted on the nozzle after a repair, or anytime a problem is reported to verify operation in accordance with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the nozzle. Any equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides are available with each test procedure or equipment can be returned to the factory for service and testing.
CAUTIONAny alterations to the nozzle and its markings could diminish safety and constitutes a misuse of this product.