mineral levelling products for substrates products...

UseLevelling correction of irregular and uneven substrates, with rapid setting and drying and compensated shrinkage. Thicknesses from 1 to 25 mm.

Compatible adhesives:- mineral adhesives with SAS technology, single and two-component organic mineral adhesives- reactive-epoxy and polyurethane, single and two-component cement-based adhesives, dispersed in water or solvent solutions

Covering materials:- porcelain tiles, ceramic tiles, klinker and cotto of all types and formats- natural stone, recomposed materials, marble- hardwood flooring, rubber, PVC, linoleum, textiles- varnishes and paints

Substrates:- cement plasters and cement-lime mortar- mineral screeds made with Keracem® Eco Prontoplus, Rekord® Eco and Keracem® Eco as a binder or pre-mixed- cement-based screeds- prefabricated concrete or fresh concrete castings- walls in concrete blocks or cellular concrete- residual traces of cement-based adhesives

Flooring and walls, for internal and external use, in domestic, commercial and industrial applications and on heat-radiant slabs.

Do not useOn high flexible substrates subject to thermal expansion, plasterboard, gypsum; on wet surfaces or substrates subject to moisture rising or which are in continuous contact with water.

AREAS OF USE

0007

3Ker

alev

el®

Eco

LR

Code

: F10

6 20

12/1

0 EN

LAYING RANGE / Mineral Levelling Products for Substrates

Certified, extra-rapid hardening, eco-friendly, mineral levelling product for the high-performance, high-thickness correction of irregular substrates, ideal for use in GreenBuilding. Low CO2 emissions and very low volatile organic compound emissions. Recyclable as an inert material at the end of its life.

Keralevel® Eco LR develops a perfect thixotropic balance which is ideal to correct walls that are out of plumb or irregular, and uneven floors without holding up site schedules and subsequent laying of floor/wall coverings.

Keralevel® Eco LR

PRODUCT STRENGTHS

t� Internal, external

t� Thicknesses from 1 to 25 mm

t� Prolonged workability, also suitable for large surface areas

t� High dimensional stability and long-lasting performance

t� High mechanical resistance

t� Suitable for laying ceramic tiles, porcelain tiles, natural stone, hardwood floors and resilient materials using adhesives

ECO NOTES

- Formulated with locally-sourced minerals meaning lower greenhouse gas emission during transportation

- Can be recycled as mineral inert material, avoiding waste disposal costs and environmental impact

GREENBUILDING RATING®

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

4

®

Regional Mineral ≥

60

% Regional Mineral ≥

30

%

Recycled

≤ 250 g/ kg

IAQVOCIndoor Air Qualit

y

Low Emission

Recyclable

Natural mineral content

61%

CO2/kg emission

217 g

Very low VOC emissions

Can be recycled as

inert material

Keralevel® Eco LR - Category: Inorganic Mineral Products - Class: Mineral Levelling Products - Rating: Eco 4

* ÉMISSION DANS L’AIR INTÉRIEUR Information sur le niveau d’émission de substances volatiles dans l’air intérieur, présentant un risque de toxicité par inhalation, sur une échelle de classe allant de A+ (très faibles émissions) à C (fortes émissions).

EN 13813

NO

RMA EUROPEA

C O N F O R M E

C20-F6EN 13813

CT CO

NTRIBUTES TO

P O I N T S

Preparation of substrates In general, substrates must be free of dust, oil and grease, free from any moisture rising, with no loose, flaky or imperfectly anchored parts such as residues of cement, lime, paint coatings and adhesives, which must be completely removed. The substrate must be stable, non-deformable, without cracks and have already completed the curing period of hygrometric shrinkage. Low-absorption substrates: smooth substrates with very low absorbency level or which are completely non-absorbent, such as ceramic tiles, marble floor tiles, epoxy and wall paints, residual traces of oxidised adhesives and smoothed concrete coatings which are com-pact and properly anchored, must be prepared by means of mechanical abrasion or by application of Keragrip Eco, the water-based, eco-friendly adhesion promoter, following the instructions for use and after having carried out thorough cleaning of the surface. Any substances used for surface treatment, such as wax or parting compounds, must be removed mechanically or using specific chemical products.High-absorbency substrates: on screeds and plasters which are compact but very absorbent, first Primer A Eco, eco-friendly, water-based surface isolation, in order to reduce and regulate the level of absorption. In the case of absorbent substrates with weak consist-ency, apply Keradur Eco eco-friendly, water-based deep consolidant. Respect the indicated waiting time before carrying out correction of the surface with a levelling product.

PreparationPrepare Keralevel® Eco LR in a clean container, first of all pouring in a quantity of water equal to approximately ¾ of the amount required. Gradually add Keralevel® Eco LR to the container, mixing the paste with a low-rev (≈ 400/min.) helicoidal agitator. Add more water until the desired consistency is obtained. The mixture must be of smooth consistency and without any lumps. For best results, and to mix larger quantities of levelling product, a stirring device with vertical blades and slow rotation is recommended. Specific polymers with high-dispersion properties ensure that Keralevel® Eco LR is immediately ready for use. The amount of water to be added, indicated on the packaging, is an approximate guide. It is possible to obtain mixtures with consistency of variable thixotropy according to the application to be made. Adding extra water does not improve the workability of the product, and may cause shrinkage in the plastic phase of drying and result in less effective final performance with a reduction in surface hardness, compressive strength and adhesion to the substrate.

ApplicationKeralevel® Eco LR is generally applied with a smooth trowel. If necessary, the high level of thixotropy of the mixture allows for high levelling thicknesses with just one coating. It is advisable to press down hard with the trowel during application so as to regulate the absorption of water and obtain maximum adhesion to the substrate,. After that, the thickness can be adjusted as required. In the case of high thicknesses and extensive surface areas it is advisable to create levelling layers, using Keralevel® Eco LR, and then proceed to apply with a trowel and flatten for final correction. The appearance of the surface finish may vary depending on whether a smooth steel spreader or a sponge spreader has been used for application. For subsequent laying of ceramic tiles it is always advisable to obtain a roughened, porous surface. If an additional correction layer is required, it must be applied as soon as the previous layer is ready for foot traffic (≈ 2 hrs at 23 °C and 50% R.H.) but after the application of Keragrip Eco eco-friendly adhesion promoter, following the instructions for use. After this time, it is necessary to wait ≈ 5-7 days, depending on the thickness created, then apply Keragrip Eco and overlay.

CleaningResidual traces of Keralevel® Eco LR can be removed from tools using water before the product hardens.

INSTRUCTIONS FOR USE

Deformable substrates: in the case of timber substrates or which in any case are liable to movement, apply Keragrip Eco, the eco-friendly adhesion promoter to a clean supporting surface, following the instructions for use. Attach an anti-alkali mesh with 4x5 mm mesh size and mix Keralevel® Eco LR with Keraplast Eco 337 the eco-friendly, water-based latex instead of water, until the required consistency has been obtained. Large continuous surfaces: continuous, extensive surfaces need to be fractionized with elastic joints so as to create areas of ≈ 50 m2. Before laying, it is advisable to apply Keragrip Eco, the eco-friendly adhesion promoter to improve adhesion to the substrate and insert an anti-alkali mesh with 4x5 mm mesh size.Special substrates: anhydrite screeds must be dry and sanded as specified in the manufacturer’s instructions, then waterproofed with water-based, eco-friendly surface isolation Primer A Eco, following the instructions for use. For subsequent laying of hardwood floors, create a smooth finish with thickness ≥ 3 mm.

SPECIAL NOTES

Certified, high-performance correction of substrates from 1 to 25 mm thickness must be carried out using a fast-acting, high thickness, eco-friendly mineral levelling product, such as Keralevel® Eco LR by Kerakoll Spa, compliant with EN 13813 class CT – C20 – F6, Green-Building Rating® Eco 4, suitable for subsequent laying of tiles after ≈ 2 hrs and for laying of natural stone, hardwood floors and resilient materials ≈ 12 hrs after application, at 23 °C 50% R.H. Apply the product using a smooth spreader on the previously prepared, clean and dimensionally stable substrate and finish with a rigid float. Average coverage: ≈ 1.5 kg/m2 per mm of thickness created.

ABSTRACT

0007

3Ker

alev

el®

Eco

LR

Code

: F10

6 20

12/1

0 EN

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com

The Eco and Bio classifications refer to the GreenBuilding Rating Manual 2012. This information was last updated in September 2012 (ref. GBR Data Report - 10.12); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The techni-cal data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV certified 2951/11.01.02HIGH-TECHAdhesion to concrete after 28 days ≥ 1 N/mm2 EN 13892-8Resistance to:- Compressive strength after 28 days ≥ 20 N/mm2 EN 13892-2- flexural after 28 days ≥ 6 N/mm2 EN 13892-2- abrasion after 28 days ≤ 250 mm3 EN 12808-2Surface hardness after 28 days ≥ 30 N/mm2 EN 13892-6Conformity CT - C20 - F6 EN 13813Values taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Appearance Pre-mixedApparent volumetric mass ≈ 1,45 kg/dm3 UEAtc/CSTB 2435Mineralogical nature of inert material silicate - crystalline carbonateGrading ≈ 0 - 600 µm UNI 10111Shelf life ≈ 6 months in the original packaging in dry environmentPack Bags 25 kgMixing water ≈ 6 l / 1 25 kg bagSpecific weight of the mixture ≈ 1,62 kg/dm3 UNI 7121Pot life ≥ 20 min.Temperature range for application from +5 °C to +30 °CMaximum thickness from 1 mm to 25 mmFoot traffic ≈ 2 hrsWaiting time before laying:- ceramic tiles, terracotta ≈ 2 hrs- hardwood floors, resilient materials and natural stone ≈ 12 hrsCoverage ≈ 1,5 kg/m2 per mm of thicknessValues taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

- Product for professional use- abide by any standards and national regulations- do not use Keralevel® Eco LR for levelling purposes or for the correction of substrate irregularities greater than 25 mm- Do not add other binders or additives to the mixture- low temperatures and high relative humidity lengthen drying times- An excessive quantity of water will reduce strength and the drying time- Before laying hardwood floors and resilient materials, check residual humidity with a calcium carbide hygrometer- Protect from direct sunlight and currents of air for the first 12 hrs- respect the elastic joints present in the substrate- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - [email protected]

WARNING

0007

3Ker

alev

el®

Eco

LR

Code

: F10

6 20

12/1

0 EN


0013

3Ker

alev

el®

Eco

Ultr

a Co

de: F

119

2013

/05

UK

UseLevelling correction of irregular and uneven substrates, with rapid setting and drying and compensated shrinkage. Thicknesses from 1 to 20 mm.


Covering materials:- hardwood floors, PVC, linoleum, rubber in domestic, industrial and sports applications, textiles and cork- porcelain tiles, ceramic tiles, klinker and cotto of all types and formats- natural stone, recomposed materials, marble- varnishes and paints

Substrates:- cement plasters and cement-lime mortar- mineral screeds or screeds made with Keracem® Eco Prontoplus, Rekord® Eco and Keracem® Eco as a binder or pre-mixed- cement-based screeds- prefabricated concrete or fresh concrete castings- walls in concrete blocks or cellular concrete- residual traces of cement-based adhesives

Flooring and walls, for internal and external use, in domestic, commercial and industrial applications and on heat-radiant slabs.Suitable for floors subject to concentrated loads, castors and wheels (EN 12529)

Do not useOn high flexible substrates subject to thermal expansion, plasterboard, gypsum; on wet surfaces or substrates subject to moisture rising or which are in continuous contact with water.

AREAS OF USE

PRODUCT STRENGTHS

• Thicknesses from 1 to 20 mm• Approved for marine use• Suitable for laying ceramic and porcelain tiles, natural

stone, hardwood floors and resilient materials using adhesives



2

®


60


30

%

Recycled

≤ 250 g/ kg


y

Low Emission

Recyclable


Can be recy-cled as inert

material

Keralevel® Eco Ultra - Category: Inorganic Mineral Products - Class: Mineral levelling products for substrates - Rating: Eco 2

Certified, extra-rapid hardening, eco-friendly, mineral levelling product for the high-performance, high-thickness correction of irregular substrates, ideal for use in GreenBuilding. With very low volatile organic compound emissions, recyclable as an inert material at the end of its life.

Keralevel® Eco Ultra develops high levels of mechanical resistance even for low thickness corrections and hardens quickly to allow hardwood and resilient material floors to be laid.

Keralevel® Eco Ultra

EN 13813

CO

MPLIANT WITH

EUROPEAN NORM

C40-F7EN 13813

CT CO

NTRIBUTES TO

P O I N T S

Preparation of substrates In general, substrates must be free of dust, oil and grease, free from any moisture rising, with no loose, flaky or imperfectly anchored parts such as residues of cement, lime, paint coatings and adhesives, which must be completely removed. The substrate must be stable, non-deformable, without cracks and have already completed the curing period of hygrometric shrinkage. Low-absorption substrates: smooth substrates with very low absorbency level or which are completely non-absorbent, such as ceramic tiles, marble floor tiles, epoxy and wall paints, residual traces of oxidised adhesives and smoothed concrete coatings which are compact and properly anchored, must be prepared by means of mechanical abrasion or by application of Keragrip Eco, the eco-friendly adhesion promoter, following the instructions for use and after having carried out thorough cleaning of the surface. Any substances used for sur-face treatment, such as wax or parting compounds, must be removed mechanically or using specific chemical products.High-absorbency substrates: on substrates and plasters which are compact but very absorbent, first apply Primer AD Eco or Primer A Eco to reduce and regulate the level of absorption. In the case of absorbent substrates with weak consistency, apply Primer AD Eco or Keradur Eco. Respect the indicated waiting time before carrying out correction of the surface with a levelling product.

PreparationPrepare Keralevel® Eco Ultra in a clean container, first of all pouring in a quantity of water equal to approximately 3/4 of that which will be required. Gradually add Keralevel® Eco Ultra to the container, mixing the paste with a low-rev (≈ 400/min.) helicoidal agitator. Add more water until the desired consistency is obtained. The mixture must be of smooth consistency and without any lumps. For best results, and to mix larger quantities of levelling product, a stirring device with vertical blades and slow rotation is recommended. Specific polymers with high-dispersion properties ensure that Keralevel® Eco Ultra is immediately ready for use. The amount of water to be added, indi-cated on the packaging, is an approximate guide. It is possible to obtain mixtures with consistency of variable thixotropy according to the application to be made. Adding extra water does not improve the workability of the product, and may cause shrinkage in the plastic phase of drying and result in less effective final performance with a reduction in surface hardness, compressive strength and adhesion to the substrate.

ApplicationKeralevel® Eco Ultra is generally applied using a smooth spreader or a trowel. If necessary, the high level of thixotropy of the mixture allows for high levelling thicknesses with just one coating. It is advisable to press down hard with the trowel during application so as to regulate the absorption of water and obtain maximum adhesion to the substrate,. After that, the thickness can be adjusted as required. In the case of high thicknesses and extensive surface areas it is advisable to create levelling layers, using Keralevel® Eco Ultra, and then proceed to apply with a trowel and smooth for final correction. The appearance of the surface finish may vary depending on whether a smooth steel spreader or a sponge spreader has been used for application. For subsequent laying of ceramic tiles it is always advisable to obtain a roughened, porous surface. If an additional correction layer is required, it must be applied as soon as the previous layer is ready for foot traffic (≈ 2 hrs at +23 °C and 50% R.H.) but after the application of Keragrip Eco eco-friendly adhesion promoter, following the instructions for use. After this time, it is necessary to wait ≈ 5-7 days, depending on the thickness created, then apply Keragrip Eco and overlay.

CleaningResidual traces of Keralevel® Eco Ultra can be removed from tools with water before the product hardens.


Deformable substrates: in the case of substrates such as wood, that are liable to movement, apply Keragrip Eco, the eco-friendly adhe-sion promoter to a clean supporting surface, following the instructions for use. Attach an anti-alkali mesh with 4x5 mm mesh size and mix Keralevel® Eco Ultra with Keraplast Eco 337 the eco-friendly, water-based latex instead of water, until the required consistency has been obtained. Large continuous surfaces: continuous, extensive surfaces need to be fractionized with elastic joints so as to create areas of ≈ 50 m2. Before laying, it is advisable to apply Keragrip Eco, the eco-friendly adhesion promoter to improve adhesion to the substrate and insert an anti-alkali mesh with 4x5 mm mesh size.Special substrates: anhydrite screeds must be dry and sanded as specified in the manufacturer’s instructions, then waterproofed with water-based, eco-friendly surface isolation Primer A Eco, following the instructions for use. Laying hardwood floors: for subsequent laying of hardwood floors, create a smooth finish with thickness ≥ 3 mm.Floors with points of concentrated load: in the case of flooring which has to bear concentrated loads and withstand the strain of furni-ture fitted with castors, apply a coat of Keralevel® Eco Ultra ≥ 1 mm (EN 12529).

SPECIAL NOTES

0013

3Ker

alev

el®

Eco

Ultr

a Co

de: F

119

2013

/05

UK

The Eco and Bio classifications refer to the GreenBuilding Rating Manual® 2013. This information was last updated in April 2013 (ref. GBR Data Report - 05.13); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 [email protected] - www.kerakoll.com

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV certified 964/11.01.02HIGH-TECHAdhesion to concrete after 28 days ≥ 2,5 N/mm2 EN 13892-8Resistance to:- compressive strength after 3 hrs ≥ 20 N/mm2 EN 13892-2- Compressive strength after 28 days ≥ 40 N/mm2 EN 13892-2- flexural after 28 days ≥ 7 N/mm2 EN 13892-2- strain parallel to the laying surface ≥ 3,5 N/mm2 UNI 10827- abrasion after 28 days ≤ 200 mm3 EN 12808-2Surface hardness after 28 days ≥ 65 N/mm2 EN 13892-6Conformity CT - C40 - F7 EN 13813Values taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Appearance Pre-mixedApparent volumetric mass ≈ 1,27 kg/dm3 UEAtc/CSTB 2435Mineralogical nature of inert material silicate - crystallineGrading ≈ 0 – 600 µm UNI 10111Shelf life ≈ 6 months in the original packaging in dry environmentPack Bags 25 kgMixing water ≈ 5.5 l / 1 x 25 kg bagSpecific weight of the mixture ≈ 1,96 kg/dm3 UNI 7121Pot life ≥ 10 min.Temperature range for application from +5 °C to +30 °CMinimum thickness ≥ 1 mmMaximum thickness obtainable ≤ 20 mmFoot traffic ≈ 2 hrsWaiting time before laying ≈ 1 hr with a 5 mm thicknessCoverage ≈ 1,4 kg/m2 per mm of thicknessValues taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate.


- Product for professional use- abide by any standards and national regulations- do not use Keralevel® Eco Ultra for levelling purposes or for the correction of substrate irregularities greater than 20 mm- Do not add other binders or additives to the mixture- low temperatures and high relative humidity lengthen drying times- An excessive quantity of water will reduce strength and the drying time- Before laying hardwood floors and resilient materials, check residual humidity with a calcium carbide hygrometer- protect from direct sunlight and air currents during the drying phase- respect the elastic joints present in the substrate- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - [email protected]

WARNING00

133K

eral

evel

® E

co U

ltra

Code

: F11

9 20

13/0

5 UK


UseLevelling of uneven substrates, with normal setting and drying and compensated shrinkage. Thicknesses up to 10 mm. In domestic, commercial and industrial applications and on heat-radiant slabs.


Before laying:- porcelain and ceramic tiles, klinker, cotto of all types and formats,- natural stones and agglomerate materials, - hardwood floors, textile coverings, rubber, PVC, linoleum, - varnishes and paints

Suitable for use on cement-based plasters or lime and cement mortars, on cement screeds or screeds made using Rekord® Eco or Keracem® Eco as eco-friendlly binder or ready-for-use premixed products, cement-based screeds, concrete and residual traces of cement-based adhesives.

Do not useOn highly flexible substrates subject to thermal expansion, or on wet surfaces or substrates subject to continuous moisture rising.

AREAS OF USE

0007

2Ker

alev

el®

Eco

Cod

e: F

105

2011

/11

UK

PRODUCT STRENGTHS

t� Internal, external

t� Suitable for laying ceramic and porcelain tiles, natural stone, hardwood floors and resilient materials using adhesives



2

®


60


30

%

Recycled

≤ 250 g/ kg


y

Low Emission

Recyclable

Very low VOC emissions< 50 µg/m3

Can be recycled as

inert material

Keralevel® Eco - Category: Inorganic Mineral Products - Class: Mineral levelling products for substrates - Rating: Eco 2

Certified, thixotropic, eco-friendly, normal-setting mineral levelling product for the high-performance correction and extended workability of irregular substrates, ideal for use in GreenBuilding. With very low volatile organic compound emissions, recyclable as an inert material at the end of its life.

Keralevel® Eco develops extended workability times, thereby guaranteeing the correction of large surfaces even in extreme climatic conditions with a smooth finish that is ideal for the subsequent laying of coverings using eco-friendly adhesives.

Keralevel® Eco

EN 13813

CO

MPLIANT WITH

EUROPEAN NORM

C25-F6EN 13813

CT CO

NTRIBUTES TO

P O I N T S

Preparation of substrates Substrates must be free from dust, oil and grease, free from any rising damp, with no loose, flaky material. The substrate must be stable, non-deformable, without cracks and have already completed the curing period of hygrometric shrinkage.On screeds and plasters which are compact but very absorbent apply Primer A Eco, a eco-friendly, water-based, surface insulation product, in order to reduce and regulate the level of absorption.

Instruction for usePrepare Keralevel® Eco in a clean container, first of all pouring in a quantity of water equal to approximately ¾ of the amount required. Gradually add Keralevel® Eco to the water in the container, mixing the paste with a suitable low-rev (≈ 400/min.) electric mixer. Then add more water until a smooth, lump-free mortar is obtained. Keralevel® Eco is immediately ready for use. The amount of water to be added, indicated on the packaging, is an approximate guide. Adding extra water does not improve the workability of the levelling product, and may cause shrinkage during drying and result in less effective final performance with a reduction in surface hardness, compressive strength and adhesion to the substrate.


The Eco and Bio classifications refer to the GreenBuilding Rating Manual 2011. This information was last updated in November 2011 (ref. GBR Data Report - 10.11); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 [email protected] - www.kerakoll.com

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1 GEV-Emicode GEV certified 2954/11.01.02HIGH-TECHAdhesion to concrete after 28 days ≥ 1 N/mm2 EN 13892-8Resistance to- Compressive strength after 28 days ≥ 25 N/mm2 EN 13892-2- flexural after 28 days ≥ 6 N/mm2 EN 13892-2- abrasion after 28 days ≤ 250 mm3 EN 12808-2Surface hardness after 28 days ≥ 40 N/mm2 EN 13892-6Conformity CT - C25 - F6 EN 13813Values taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

- Product for professional use- abide by any standards and national regulations- do not use Keralevel® Eco for levelling purposes or for the correction of substrate irregularities greater than 10 mm- Do not add other binders or additives to the mixture- low temperatures and high relative humidity lengthen drying times- An excessive quantity of water will reduce strength and the drying time- Before laying hardwood floors and resilient materials, check residual humidity with a calcium carbide hygrometer- Protect from direct sunlight and currents of air for the first 12 hrs- respect the elastic joints present in the substrate- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - [email protected]

WARNING

0007

2Ker

alev

el®

Eco

Cod

e: F

105

2011

/11

UK

Appearance Pre-mixedSpecific weight ≈ 1,45 kg/dm3 UEAtc/CSTB 2435Mineralogical nature of inert material crystalline carbonateGrading ≈ 0 - 600 µm UNI 10111Shelf life ≈ 12 months in the original packaging in dry environmentPack Bags 25 kgMixing water ≈ 6,5 l / 1 bag 25 kg Specific weight of the mixture ≈ 1,86 kg/dm3 UNI 7121Pot life ≥ 4 hrsTemperature range for application from +5 °C to +35 °CMaximum thickness from 1 to 10 mmFoot traffic ≈ 24 hrsWaiting time before laying:- ceramic tiles, terracotta ≈ 24 hrs- hardwood floors, resilient materials and natural stone ≈ 3 daysCoverage ≈ 1,5 kg/m2 per mm of thicknessValues taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate.


In the case of wooden substrates that are deformable or subject to movement, apply Keragrip Eco eco-friendly, water-based, single-component adhesion promoter to the clean substrate, following the instructions for use. Fix a suitable anti-alkali fibre mesh and mix Keralevel® Eco with Keraplast Eco P6 eco-friendly, water-based latex in place of the mixing water, until the required consistency is obtained.Continuous, extensive areas need to be fractionized with elastic joints so as to create areas of ≈ 50 m2.Gypsum-based screeds must be dry, sanded and vacuum cleaned according to the manufacturer’s instructions and insulated with Primer A Eco eco-friendly, concentrated, water-based surface insulation.For subsequent laying of hardwood floors, create a smooth finish with thickness ≥ 3 mm.

SPECIAL NOTES

Keralevel® Eco is applied with a smooth trowel. Due to the highly thixotrpic structure of the mixture this allows for high levelling thicknes-ses with just one coat. It is advisable to press down hard with the trowel during application so as to regulate the absorption of water and obtain maximum adhesion to the substrate,. For subsequent laying of ceramic tiles it is always advisable to obtain a roughened surface.

ToolsElectrical mixer, spreader and trowel. Wash tools with water before the product hardens.


• Internal, external

• Prolonged workability, also suitable for large surface areas

• High mechanical resistance

Keralevel® Eco Finish - Category: Inorganic Mineral Products - Class: Mineral levelling products for substrates - Rating: Eco 2



PRODUCT STRENGTHS

LAYING RANGE / Mineral levelling products for substrates

0013

9Ker

alev

el®

Eco

Fin

ish

Code

: F12

0 20

16/0

7

2

®


60


30

%

Recycled

≤ 250 g/ kg


y

Low Emission

Recyclable


Can be recycled as

inert material

Certified, thixotropic, normal-setting, eco-friendly mineral levelling product to smooth rough or rustic substrates, ideal for use in GreenBuilding. With very low volatile organic compound emissions, recyclable as an inert material at the end of its life.

Keralevel® Eco Finish develops extended workability times thereby guaranteeing perfectly smooth finishes even with very low thicknesses with no surface tacking, which is ideal for the subsequent laying of resilient material and carpeted floors and coverings.

Keralevel® Eco Finish

EN 13813

CO

NTRIBUTES TO

P O I N T S

UseSmoothing of irregular substrates with normal setting and compensated shrinkage. Thicknesses up to 2 mm.

Compatible adhesives:- single-component and two-component organic mineral- reactive-epoxy and polyurethane, single and two-components, dispersed in water and in solvent solutions

Covering materials:- textiles, rubber, PVC, linoleum- varnishes and paints- wallpaper

Substrates:- cement-based plasters and cement-lime mortar, levelling and self-levelling cement-based mortars- mineral screeds or screeds made with Keracem® Eco Prontoplus, Rekord® Eco and Keracem® Eco as a binder or pre-mixed- cement-based screeds

Flooring and walls, for internal and external use, in domestic, commercial and industrial applications and on heat-radiant slabs. Suita-ble for floors subject to concentrated loads, castors and wheels (EN 12529).

Do not useOn gypsum-based plasters/renders and anhydrite screeds without the use of Primer A Eco water-based, eco-friendly, surface insulation; on highly flexible substrates and thermal expansion, and on plasterboard; on wet substrates or subject to continuous moisture rising.

AREAS OF USE

Preparation of substratesSubstrates must be stable, dry, free from any rising damp, without cracks, free from dust, oil, grease and loose, flaky parts. On substrates which are compact but very absorbent, apply Primer A Eco or Primer AD Eco to reduce and regulate the level of absorption. In the case of absorbent substrates with weak consistency apply Keradur Eco.



EN 13813 STANDARD

C3 0 -F6 CTCLASS CHARACTERISTICS

0013

9Ker

alev

el®

Eco

Fin

ish

Code

: F12

0 20

16/0

7

PreparationPrepare Keralevel® Eco Finish in a clean container by pouring in ≈ ¾ of the water required. Gradually add Keralevel® Eco Finish to the water, mixing the paste with a low-rev (≈ 400/min.) helicoidal agitator. Add water until a homogeneous, lump-free mortar is obtained. The amount of water to be added, indicated on the packaging, is an approximate guide.

ApplicationApply Keralevel® Eco Finish with a smooth spreader. The high level of thixotropy of the mixture allows for high finishing thicknesses with just one coating. It is generally advisable to apply an initial fine layer, pressing the product down to obtain maximum adhesion to the substrate and to adjust water absorption of subsequent layers. The appearance of the finish will vary depending on whether a smooth steel spreader or a sponge spreader has been used for application.

CleaningResidual traces of Keralevel® Eco Finish can be removed from tools with water before the product hardens.


Anhydrite screeds: must be dry and sanded according to the manufacturer’s instructions and prepared with Primer A Eco following the instructions for use.Substrates subject to flexure: apply Primer A Eco to the substrate, mix Keralevel® Eco Finish with 50% Keraplast Eco 337 and 50% water.Fine smoothing layers: applications from 0 to 1 mm of thickness refer to smooth finishes which fill the porosity of a substrate without increasing thicknesses. It is advisable to reduce and uniform the absorption of substrates by applying Primer AD Eco or Primer A Eco.Floors with points of concentrated load: in the case of flooring which has to bear concentrated loads and withstand the strain of furniture fitted with castors, apply a coat of Keralevel® Eco Finish ≥ 1 mm (EN 12529).

SPECIAL NOTES

Certified, high-performance levelling of substrates of 2 mm thickness must be carried out using a thixotropic eco-friendly mineral levelling product, with normal setting and smooth finishing, such as Keralevel® Eco Finish by Kerakoll Spa, compliant with EN 13813 class CT - C30 - F6, GreenBuilding Rating® Eco 2, suitable for subsequent laying of textile coverings, resilient materials and wallpaper ≈ 12 hrs after application, at +23 °C 50% R.H. Apply the product using a smooth spreader on the previously prepared, clean and dimensionally stable substrate and finish with a rigid float. Average coverage: ≈ 1.4 kg/m2 per mm of thickness created.

ABSTRACT

Appearance Pre-mixedSpecific weight ≈ 0,99 kg/dm3 UEAtc/CSTB 2435Mineralogical nature of inert material silicate - crystalline carbonateGrading ≈ 0 – 125 µm UNI 10111Shelf life ≈ 12 months in the original packaging in dry environmentPack 25 kg bagsMixing water ≈ 7,6 ℓ / 1 25 kg bagSpecific weight of the mixture ≈ 1,89 kg/dm3 UNI 7121Pot life ≥ 2 hrsTemperature range for application from +5 °C to +35 °CMaximum thickness up to 2 mmFoot traffic ≈ 8 hrsWaiting time before laying:- resilient materials, wallpaper, paints ≈ 12 hrsCoverage ≈ 1.4 kg/m2 per mm of thicknessValues taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate.


The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in June 2016 (ref. GBR Data Report - 07.16); please note that additions and/or amendments to this information may be made over time by KERAKOLL Spa; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) ItalyTel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com

ISO 9001CERTIFIEDIT10/0327

ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

0013

9Ker

alev

el®

Eco

Fin

ish

Code

: F12

0 20

16/0

7

- Product for professional use- abide by any standards and national regulations- do not use Keralevel® Eco Finish for levelling purposes or for the correction of substrate irregularities greater than 2 mm- do not add other binders or additives to the mixture- low temperatures and high relative humidity lengthen drying times- an excessive quantity of water will reduce strength and the drying time- protect from direct sunlight and air currents during the drying phase- respect the elastic joints present in the substrate- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - [email protected]

WARNING

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV certified 2953/11.01.02HIGH-TECHAdhesion to concrete after 28 days ≥ 1,5 N/mm2 EN 13892-8Resistance to:- compressive strength after 28 days ≥ 30 N/mm2 EN 13892-2- flexural after 28 days ≥ 6 N/mm2 EN 13892-2- abrasion after 28 days ≤ 400 mm3 EN 12808-2Conformity CT – C30 – F6 EN 13813Values taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE


Kera

leve

l® E

co R

P Co

de: F

121

2016

/07

EN

Organic, eco-friendly mineral finishing product for compact, absorbent and non-absorbent substrates, ideal for use in GreenBuilding. Single-component, solvent-free, safeguards the health of both operators and the environment. Contains locally-sourced recycled raw materials.

Keralevel® Eco RP allows the high-adhesion smoothing of surfaces and grouting joints for the subsequent application of mineral finishing coatings before overlaying resilient material and carpet coverings.

Keralevel® Eco RP

• For internal use

• Ready-to-use

• Ideal in renovation work

• Easy to sand

PRODUCT STRENGTHS



4

®


30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care


76%Solvent-free

No environmental hazard rating

Non-toxic and non-hazardous

UseLevelling and smoothing of irregular absorbent or non-absorbent substrates. Preparation of non-absorbent substrates before application of cement-based levelling or self-levelling products. Thickness from 0 to 1 mm.

Products suitable for overlaying:- mineral levelling and self-levelling products, organic mineral adhesives in dispersing medium- cement-based levelling and self-levelling products- water-dispersed adhesives for PVC, rubber, linoleum

Substrates:- cement-based screeds- anhydrite screeds- panelling and structures in wood- ceramic floors, porcelain tiles, marble floor tiles and natural stone

For internal use, domestic, commercial and industrial floors; underfloor heating systems.

Do not useFor external use, on substrates with high thermal expansion; in environments which are subject to moisture rising or in continuous contact with water. For levelling work before installing hardwood floors, before direct bonding with solvent-based adhesives or two-component and single-component reactive adhesives.

AREAS OF USE

Preparation of substratesThe substrates must be compact, permanently dry, free from dust, parting compounds, oil and grease, with no loose, flaky or imperfectly anchored parts such as residual traces of cement and adhesive, which must be totally removed. The substrate must be stable, without cracks and have already completed the curing period of hygrometric shrinkage. The correction must be desolidarised from all vertical elements and walls by means of a band in non-deformable material with a thickness of 8/10 mm. On highly absorbent substrates and heated substrates apply Primer AD Eco. Prepare anhydrite screeds according to the manufacturer’s instructions and apply Primer A Eco.

PreparationThe product is ready-to-use. mix before use.

ApplicationKeralevel® Eco RP should be applied with a smooth spreader or trowel to a maximum thickness of 1 mm, using the coverage indicated.

CleaningResidual traces of Keralevel® Eco RP can be removed with water before the product hardens.


CO

NTRIBUTES TO

P O I N T S


The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in June 2016 (ref. GBR Data Report - 07.16); please note that additions and/or amendments to this information may be made over time by KERAKOLL Spa; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) ItalyTel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com

ISO 9001CERTIFIEDIT10/0327

ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

Kera

leve

l® E

co R

P Co

de: F

121

2016

/07

EN

For laying covering materials directly on Keralevel® Eco RP, keep in mind that this creates non-absorbent surfaces. All breathable textile covering materials can be bonded with the usual adhesives dispersed in water.When laying all other floors that are poorly breathable or non-breathable, on Keralevel® Eco RP, we recommend that a levelling of at least 2 mm be performed, and that bonding be done with water-dispersed adhesives that have extended tack.in addition to the above information, installation instructions provided by the manufacturer of the floorcoverings used must also be followed, along with the technical sheets applicable to other products mentioned.

SPECIAL NOTES

Levelling and smoothing of the 1 mm base coat will be carried out using eco-friendly, organic mineral finishing product, GreenBuilding Rating® Eco 4, such as Keralevel® Eco RP, by Kerakoll Spa, suitable for subsequent application of mineral levelling and self-levelling products and dispersed organic mineral adhesives for the laying of resilient materials and carpet. Prepare, clean and make the substrate dimensionally stable first, then apply the product with a smooth spreader. Average coverage: ≈ 1.3 kg/m2 per 1 mm.

ABSTRACT

- Product for professional use- abide by any standards and national regulations- do not add binders, inert materials, additives or water during the setting phase- low temperatures and high relative humidity lengthen drying times- protect from direct sunlight and air currents during the drying phase- respect the structural joints present in the substrate- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - [email protected]

WARNING

Appearance beige pastePack 15 kg bucketsShelf life ≈ 12 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatTemperature range for application from +10 °C to +30 °CMaximum thickness ≤ 1 mm with just one coatingFoot traffic ≈ 1 hWaiting time before laying from 2 to 3 hrsCoverage ≈ 1.3 kg/m2 per mm of thicknessValues taken at a temperature of +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate.


UseHigh-resistance adjustment and finishing of irregular and uneven substrates, whether absorbent or non-absorbent. Thicknesses from 1 to 5 mm.

Compatible adhesives:- reactive, single-component and two-component

Covering materials:- porcelain tiles, ceramic tiles, klinker and cotto of all types and formats- natural stone, recomposed materials, marble- hardwood flooring, rubber, PVC, linoleum, textiles- epoxy and polyurethane resin coatings

Substrates:- mineral screeds made with Keracem® Eco Prontoplus, Rekord® Eco, Rekord® Eco Pronto, Keracem® Eco and Keracem® Eco Pronto- cement-based screeds- anhydrite screeds- prefabricated concrete or fresh concrete castings- timber, plywood, hardwood floors

Flooring for internal use in residential, commercial and industrial applications and on heat-radiant slabs.

Do not useIn external applications, on substrates that are not dry or subject to moisture rising.

AREAS OF USE

0073

9Ker

alev

el®

Eco

Flo

or C

ode:

F80

8 20

13/0

6 EN


Elastic, eco-friendly, organic mineral finishing product for the high-resistance and high-adhesion correction of irregular substrates, whether absorbent or non-absorbent, ideal for use in GreenBuilding. Two-component with reduced solvent content.

Keralevel® Eco Floor can be used to level and repair cracks in flooring, guaranteeing an ideal surface for subsequent application of resilient materials, hardwood floors and resin coatings.

Keralevel® Eco Floor

PRODUCT STRENGTHS

• Ideal in Factory systems

• For internal use

• Thicknesses from 1 to 5 mm

• Suitable for overlaying on stable, non-absorbent substrates

• Ideal in renovation work

ECO NOTES

- Formulated with locally-sourced minerals meaning lower greenhouse gas emission during transportation



2

®


30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecological Im

pact

Health Care


40%

Reduced solvent content4,8 g/kg

Keralevel® Eco Floor - Category: Organic Mineral Products - Class: Mineral Levelling Products - Rating: Eco 2

EN 13813

CO

MPLIANT WITH

B2 ,0-E1EN 13813

SR

EUROPEAN NORM

CO

NTRIBUTES TO

P O I N T S

Preparation of substrates Substrates must be free of dust, oil and grease, with no loose, flaky or imperfectly anchored parts such as residues of cement, lime, paint coatings and adhesives, which must be completely removed. The substrates must be stable, non-deformable and have already completed the curing period of hygrometric shrinkage. The substrates must be permanently dry and free from moisture rising. In the event of subsequent laying of coatings in resin, PVC, rubber, linoleum, cement-based substrates must have a residual moisture at a maximum of 3% (2.5% in the case of heated substrate); anhydrite substrates must have a moisture at a maximum of 0.5% (0.2% in the case of heated substrate). In the event of subsequent laying of wood-en floors, cement-based substrates must have a residual moisture at a maximum of 2% (1.7% in the case of heated substrate); anhydrite substrates must have moisture at a maximum of 0.5% (0.2% in the case of heated substrate. In the event of subsequent laying of resin coatings the substrates must have a surface tear strength > 1.5 MPa according to ASTM D 4541 and a compressive strength > 25 N/mm².Absorbent substrates: substrates consisting of smoothed concrete floors, cement-based screeds, anhydrite screeds, with dusty surface, flaky or weak parts or in general in the event of subsequent laying of resin coatings, must be treated with Slc® Eco EP 21 diluted with Keragrip Eco Pulep up to 30% depending on the degree of absorption of the substrate.Non-absorbent substrates: substrates made of porcelain floors, ceramic, natural stone must be properly cleaned or surface abraded, in the event of subsequent laying of resin coatings.

PreparationKeralevel® Eco Floor is prepared by mixing together parts A and B from the bottom upwards, using a low-rev (400/min.) helicoidal agitator, respecting the preset ratio of the packs (Part A 9.25 kg : Part B 0.75 kg). Pour part B into the bucket containing part A, being careful to mix the two parts uniformly until a smooth, even coloured mixture is obtained. It is necessary to mix an amount of product that can be used within 30 minutes.

ApplicationApply Keralevel® Eco Floor with smooth spreader. In case of subsequent application of resin coatings, or applying a second coat of Keralevel® Eco Floor, sprinkle wet-on-wet Quartz 1.3 until saturated. Once hardened, remove any excess quartz.In case of subsequent laying of resin coatings on cracked, uneven substrates, with chases on the floor containing water/heating sys-tems, In case of substrates consisting of ceramic floors, porcelain tiles or natural stone, during the application of Keralevel® Eco Floor it is required enter Net 90 suitable reinforcing mesh in the layer of levelling coat and sprinkle wet-on-wet Quartz 1.3 until saturated. Once hardened, remove any excess quartz.

CleaningResidual traces of Keralevel® Eco Floor can be removed from tools with alcohol before the product has hardened.


If the substrate contains joints that are subject to shrinkage or movement in general, they must be brought to the surface and treated with suitable elastic sealing agents.Before the application of resin-based film, high-thickness or self-levelling coverings, sand the surfaces levelled with Keralevel® Eco Floor.

SPECIAL NOTES

The high-resistance correction of substrate in thickness from 1 to 5 mm will be provided by using eco-friendly elastic organic mineral finishing product compliant with EN13813 class SR-B2,0-E1, GreenBuilding Rating® Eco 2, such as Keralevel® Eco Floor, by Kerakoll Spa. Apply with a smooth spreader on the previously prepared substrate, dimensionally stable and permanently dry. Coverage ≈ 1.5 kg/m²/m2 per mm of thickness created.

ABSTRACT

0073

9Ker

alev

el®

Eco

Flo

or C

ode:

F80

8 20

13/0

6 EN

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 [email protected] - www.kerakoll.com

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in January 2013 (ref. GBR Data Report - 02.13); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

HIGH-TECHTensile adhesion to concrete after 28 days ≥ 2,5 MPa EN 1323Elastic modulus after 7 days ≥ 0,035 Kn/mm2 EN ISO 178Elastic modulus after 28 days ≥ 0,037 Kn/mm2 EN ISO 178Foot traffic / Overlaying +10 °C 16 hrsFoot traffic / Overlaying +15 °C 12 hrsFoot traffic / Overlaying +20 °C 6 hrsUltimate elongation after 28 days ≥ 4,5% ISO 527-2Shore A hardness at +23 °C 70Conformity SR–B2,0–E1 EN13813Values taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Appearance:- Part A beige paste- Part B straw-coloured liquidSpecific weight:- Part A ≈ 1,6 kg/dm3

- Part B ≈ 1,05 kg/dm3

Shelf life ≈ 12 months in the original packaging in dry environmentWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack part A 9.25 kg bucket- part B 0.75 kg bottleMixing ratio part A : part B = 9.25 : 0.75 Pot life ≈ 30 min. Temperature range for application from +10 °C Viscosity ≈ 120,000 mPa · s, rotor 93 RPM 50 Brookfield methodCoverage ≈ 1,5 kg/m2 per mm of thicknessValues taken at +20 °C, 65% R.H.and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate.


- Product for professional use- abide by any standards and national regulations- apply the product at substrate temperatures from +10°C- apply on permanently dry substrates- protect from direct sunlight and currents of air for the first 6 hours- do not apply on dirty or loose surfaces- dispose of as indicated in applicable legislation- the properties of products exposed to sharp changes in temperature (due to transport, storage, building site use, etc.) may be altered

(e.g. crystallisation, partial hardening, fluidization, accelerated or delayed catalysis). In most cases, when products are restored to optimal conditions, the original properties will also be restored

- protect any surfaces and objects in the application area from accidental contact with the product- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - [email protected]

WARNING00

739K

eral

evel

® E

co F

loor

Cod

e: F

808

2013

/06

EN

Date post:	22-May-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

mineral levelling products for substrates products...

Documents