8
MiniSKiiP ® IPM Evaluation Board 1 / 8 © by SEMIKRON MiniSKiiP ® IPM 600V Evaluation Board Technical Handbook Preliminary Version 1.0 / August 2010 Andreas Winterholler
MiniSKiiP ® IPM Evaluation Board
1 / 8 © by SEMIKRON
MiniSKiiP ® IPM 600V Evaluation Board
Technical Handbook
Preliminary
Version 1.0 / August 2010 Andreas Winterholler
MiniSKiiP ® IPM Evaluation Board
2 / 8 © by SEMIKRON
Revision History
Revision Date Name Changes
00 23. July 2010 A. Winterholler Target
01 09. August 2010 A. Winterholler Preliminary
Table of Contents 1 Introduction ....................................................................................................................................................................3 2 Evaluation board ............................................................................................................................................................3 3 Connector specification..................................................................................................................................................5 4 Shunt resistors ...............................................................................................................................................................5 5 Appendix ........................................................................................................................................................................5
Please note: Unless otherwise specified, all values in this technical handbook are typical values. Typical values are the average values expected in large quantities and are provided for information purposes only. These values can and do vary in different applications. All operating parameters should be validated by user’s technical experts for each application.
MiniSKiiP ® IPM Evaluation Board
3 / 8 © by SEMIKRON
1 Introduction
The MiniSKiiP IPM 600V series evaluation board provides an easy assembly to test the features and the performance of the MiniSKiiP IPM 600V series. The MiniSKiiP IPM evaluation board can be used for the “SKiiP 26NABI066V3” and for the “SKiiP 25NABI066V3”. All calculations and circuit information are explained in the “Technical Explanation MiniSKiiP IPM”.
2 Evaluation board
• Single 15V voltage source requiered • Including bootsrap circuit • Including 5V voltage regulator • ITRIP Circuit including shunts • Including T-Sense Circuit • Including input filters
Bootstrap circuit Connectors for external high side supply
Error LED
Auxillary emitter
15V / 5V LED
ITRIP Jumper 1
ITRIP Jumper 2
Fig. 1: EVA board top side
GND 15V T-Sense
Auxillary contacts
MiniSKiiP ® IPM Evaluation Board
4 / 8 © by SEMIKRON
Landing pads MiniSKiiP IPM
Contact springs
Shunts “Not assambled“
Input filters
Fig. 2: EVA board ITRIP circuit Note: If Jumper 1 is closed the function of Jumper 2 is disabled
Fig. 3: EVA board temperature sensor circuit
Fig. 4: Power connectors evaluation board
Fig. 5: EVA board bottom side
MiniSKiiP ® IPM Evaluation Board
5 / 8 © by SEMIKRON
3 Connector specification
Connector male DIN 41651 Multipoint connector male (Contact spacing 2,54 mm) Power connector on PCB diameter 6,2 mm
4 Shunt resistors
The evaluation board is designed to use SMD2817 resistors, e.g. Isabellenhütte SMT Series. For further information see “Technical Explanation MiniSKiiP IPM”. DISCLAIMER SEMIKRON reserves the right to make changes without further notice herein to improve reliability, function or design. Information furnished in this document is believed to be accurate and reliable. However, no representation or warranty is given and no liability is assumed with respect to the accuracy or use of such information. SEMIKRON does not assume any liability arising out of the application or use of any product or circuit described herein. Furthermore, this technical information may not be considered as an assurance of component characteristics. No warranty or guarantee expressed or implied is made regarding delivery, performance or suitability. This document supersedes and replaces all information previously supplied and may be superseded by updates without further notice. SEMIKRON products are not authorized for use in life support appliances and systems without the express written approval by SEMIKRON. The specification of our components may not be considered as an assurance of component characteristics. Components have to be tested for the respective application. Adjustments may be necessary. The use of SEMIKRON products in life support appliances and systems is subject to prior specification and written approval by SEMIKRON. We therefore strongly recommend prior consultation of our personal.
5 Appendix
MiniSKiiP ® IPM Evaluation Board
6 / 8 © by SEMIKRON
MiniSKiiP ® IPM Evaluation Board
7 / 8 © by SEMIKRON
MiniSKiiP ® IPM Evaluation Board
8 / 8 © by SEMIKRON
