10
Installation Manual www.commbox.com.br IP Automation Modules EN
Installation Manual
www.commbox.com.br
IP Automation Modules EN
Installation Manual - Rev. 1.3 EN
Table of Contents
Multi I/O Series Modules ............................................................................. 3
Technical specifications ............................................................................. 3
Connection examples ................................................................................. 4 Example 1 - Typical application ....................................................................... 4 Example 2 - Inductive loads ............................................................................. 5
IP configuration ........................................................................................... 7
Example 3 - MIO2408 Isolated Inputs .............................................................. 6
IP Automation Modules
02
InputsOutputsMax consumption (mA)
Dimensions (WxHxL-mm)
Weight(g)
MIO40242
25085x35x70
250
MIO40044
250130x32x82
400
MIO80088
550192x32x82
500
MIO2408248
600205x32x102
650
Installation Manual - Rev. 1.3 EN
MIO2408MIO800
MIO400MIO402
Multi I/O series Modules
Tecnhical specifications
03
IP Automation Modules
InputsVoltage range: 0~30VDCCurrent: 2mALogic levels: <5VDC=0, >5VDC=1
OutputsMax voltage: 240VACMax current: 2AForm C relays: NO, NC and C contacts available
Communication10/100Mbps Ethernet interface
LED indicatorsPowerInputsOutputsNetwork (Link/Activity)
Physical characteristicsEnclosure: steel, black paintingDimensions/weight: see table above
PowerVoltage: 12VDCConsumption: see table above
Installation Manual - Rev. 1.3 EN
PWR12VDC
220VAC
Ethernet
Example 1 - Typical application
24VDC
12VDC
PIRSensor
MagneticSensor
Bell/SounderIllumination
04
IP Automation Modules
Connection examples
Installation Manual - Rev. 1.3 EN
CONTACTORWARNING!
THIS FILTER MUSTBE INSTALLED CLOSETO THE CONTACTOR!
SNB100Snubber
220VAC
24VDC
Inductive DC Load
Inductive AC Load
1N4007 diode
Anode
Catode
05
Example 2 - Inductive loads
Connection examples
IP Automation Modules
Both "SNB100 Snubber" and "1N4007 diode", connected in parallel with the loads, aims to eliminate electrical noise caused by the switching of inductive loads, such as contactors, motors, relays and door locks, thus avoiding the generation of electromagnetic interference ( EMI).
Installation Manual - Rev. 1.3 EN
Case 1: H ctuationThe switch/actuator will connect the INPUT pin to the "+" wire of sensor PSU
igh logic level a
Case 2: Low logic level actuationThe switch/actuator will connect the GND pin to the "-" wire of sensor PSU
Sensor PSU12 VDC~30
MIO2408
MIO2408
12VDC PSU
12VDC PSU
06
Example 3 - MIO2408 isolated inputs
IP Automation Modules
Connection examples
Sensor PSU12 VDC~30
Installation Manual - Rev. 1.3 EN 07
IP configuration
MIO Configuration SoftwareAccess the site www.commbox.com.br > Downloads, then in “Automação” download the file “Software de Configuração (Device Manager)”;Run the installer.
IP ConfigurationPower up the MIO module (12VDC);Using a ethernet cable, connect the module directly to your computer (point-to-point connection);Configure your computer so it is on the same IP range of the MIO module. Example: MIO default IP = 192.168.0.100 Computer IP = 192.168.0.101Run the "Commbox 32bit Device Manager". The screen below will open:
The connected MIO module will appear in “Device List”;Select the MIO module on the list, the fields in "Connection Properties" will fill automatically;Click "Next";
IP Automation Modules
Installation Manual - Rev. 1.3 EN 08
The screen below will be opened:
Select Configurations > TCP/IP;In “TCP/IP Setings” setup the necessary fields and click "Save";Your MIO is ready to go!
IP configuration
IP Automation Modules
Installation Manual - Rev. 1.3 EN
Revision DescriptionBased on file: "MIO Series - Manual de Instalação - Rev 1.3"- English translation1.3 EN
Version Notes
09
IP Automation Modules
www.commbox.com.br
Headquarters | Porto Alegre/RS260 Goethe Av. - 90430-100
+55 (51) 3026.2300
Branch office | São Caetano do Sul/SP926 Baraldi St., rm 31 - 09510-005+55 (11) 4063.4300
