129
MISCELLANEOUS
130
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
BAM 972 • PANEL • 1 1/2” Projection• 9” w. x 72” h.
• ROUNDBAM 153 • 1 1/2” w. x 3’0” h.BAM 203 • 2” w. x 3’0” h.BAM 205 • 2” w. x 5’0” h.BAM 255 • 2 1/2” w. x 5’0” h.
ACORN 29• 25” Height • 29” Diameter
AC 1416• 12 3/8” Height• 15 3/4” Width
BA 12GB• 11 7/8” Diameter
BAM 3636• PANEL • 1 9/16” Projection• 36” w. x 36” h.
DM1000• 7 13/16” Projection• 40 1/8” Diameter
SPM 5119• 3” Projection• 19 1/2” Height • 55 1/2” WidthLARGE GOLF BALL
BAMBOOBamboo shipped unpainted
BF 200• 1 1/4” Projection
• 44 3/4” Height • 4” Width
• BRICK TEXTURE
SPECTIS RESERVES THE RIGHT TO HOLLOW OUT THE BACK OF ANY PRODUCT WITHOUT NOTICE. SOME PRODUCTS MAY BE MADE AS ASSEMBLIES.
DOME
131
w w w . s p e c t i s . c o m
MISCELLANEOUS
FT 3401• 1” Projection• 4 15/16” Width • 9 3/4” Height
FT 3400• 1” Projection• 6 15/16” Height • 26” Width
FT 3402• 1 1/8” Projection• 7 3/4” Height • 30 1/2” Width
FT 3400 FT 3402
• 26” Width • 30 1/2” Width
FT 3405• 1 1/2” Projection• 11 1/4” Height • 4 7/16” Width
FT 3407• 2” Projection• 22 1/2” Height• 7” Width
FT 3410 FT 3411 • 2” Projection • 18 1/2” Height • 4” Width
FT 3412• 4” Projection• 48” Height• 12” Width
FT 3414• 3” Projection• 38” Height • 108” Width
FT 3413• 4” Projection• 72” Height• 12” Width
FT 3414
FT 3403• 1 1/4” Projection• 9 1/4” Height • 28 5/8” Width
FT 3406• 1 7/16” Projection• 10 9/16” Height • 42 1/16” Width
FESTOONS & TASSELS
FT 3409• 1 7/16” Projection• 8 11/16” Height • 24 1/16” Width
FT 3408• 2” Projection• 22 1/2” Height• 7” Width
FT 3404• 1 3/4” Projection• 7 3/8” Height • 26 7/8” Width
132
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
FIN 48• 6” Square Base • 12/12 Pitch• 1/2” Threaded Rod• 50 1/2” Height
FIN 34• 2 7/8” Base Diam. • 34” Height
FIN 24• 2 3/8” Base Diam. • 24 1/2” Height
FIN 7• 3” Width • 7 1/8” Height• 2 1/4” Base Diam. • PVC Pipe• PVC Pipe
FIN 21• 3 1/2” Base Diam.• 6 1/2” Overall Width • 21 1/4” Height • PVC Pipe
FIN 8• 3 3/4” Width • 8” Height• 3” Base Diam. • PVC Pipe
Photo above illustrates the use of the following Spectis products: fluted box columns, balusters BAL 2047, rails RAL 2106T & RAL 2103B and finial FIN 48.
FIN 60• 9” Base Diam. • 60” Height • 1/2” Threaded RodFIN 105• 6 3/4” Base Diam.• 7 1/2” Overall Width • 45” Height • 1/2" Threaded PipeFIN 120
• 8” Base Diam.• 8” Height • 24" Round
FIN 102• 6” Base Diam.• 8 7/16” Overall Width • 32 1/4” Height • PVC Pipe
FIN 110• 4 3/4” Square Base• 79” Height
FIN 119• 3/4” Base Diam.• 17 3/4” Height
FIN 106• 3 1/2” Square Base• 43” Height
FINIALS
133
w w w . s p e c t i s . c o m
MISCELLANEOUS
FIN 32• 8” Square Base • 32” Height • PVC Pipe
FIN 13• 6” Base Diam. • 13 5/8” Height• PVC Pipe
FIN 23• 6” Square Base • 22 5/8” Height • PVC Pipe
FIN 3110• 9 1/2” Base Diam.• 31” Height • PVC Pipe
FIN 103• 2 3/16” Base Diam.• 7 1/4” Height • PVC Pipe
FIN 104• 3 7/8” Square Base• 9” Height • PVC Pipe
FIN 107• 7 1/4” Base Diam.• 13” Height
FIN 108• 1 3/4” Base Diam.• 5 1/2” Height
FIN 109• 2 1/2” Base Diam.• 5 1/4” Height • Round FIN 111
• 4” Square Base• 8 1/4” Height • PVC Pipe
FIN 112• 12” Base Diam.• 30 1/2” Height • PVC Pipe
FIN 113• 8 1/2” Base Diam.• 18 1/2” Height • 1/2" Threaded Pipe
FIN 114• 7 1/2” Base Diam.• 25 1/2” Height
FIN 115• 19 1/4” Base Diam.• 48” Height
FIN 116• 9 1/4” Base Diam.• 41 1/4” Height • 1/2" Threaded Pipe
FIN 117• 15” Square Base• 32 1/2” Height • PVC Pipe
FIN 118• 5” Square Base• 10 3/8” Height • PVC Pipe
FINIALS
134
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
VG 101• 7/16” Projection
• 6 1/4” Height• 11 7/8” Width
VG 106• 7/16” Projection
• 8” Height• 12” Width
VG 104 • 7/16” Projection • 6 1/4” Height • 77” Width • 10 7/8” Repeat
VG 100• 5/16” Projection • 10” Height• 20” Width
VG 102• 5/16” Projection
• 10” Height• 10” Width
VG 102• 5/16” Projection
• 10” Height• 10” Width
CUPOLA 2125• 21” w. x 25 1/4” h.
• Available with painted copper roof
• Venting with screen• Shipped Unassembled
• CAN BE MITEREDQN 102• 1 1/2” Projection• 84” w. x 13” h.QN 103• 1 1/2” Projection• 16” w. x 16” h.
QN 104• 1 1/2” Projection• 38” w. x 18” h.QN 105• 1 1/2” Projection• 34” w. x 16” h.
QN 106• 1 1/2” Projection• 32” w. x 10” h.
CUPOLA 2125• 21” w. x 25 1/4” h.
• Available with painted copper roof
• Venting with screen• Shipped Unassembled
SB 3100R• 12” Projection• 7 1/2” Height • 3/4” Width
SB 3100R• 12” Projection• 7 1/2” Height • 3/4” Width
SB 3100L• 12” Projection• 7 1/2” Height
• 3/4” Width
VG 105• 3/4” Projection • 6” Height• 10” WidthVG 103• 3/4” Projection • 14” Height• 30” Width
VG 109• 1 3/4” Projection • 22 3/4” Height• 30 3/4” Width
STAIR BRACKETS
GRILLE COVERS
QUOIN
135
w w w. s p e c t i s . c o m
MISCELLANEOUS
OVAL 2032 SGwith Starburst Grille
• R.O. 20 1/2” w. x 32 1/2” h. • Also Available Round Starburst Grille
OVAL 2032 DGwith Diamond Grille
• R.O. 20 1/2” w. x 32 1/2” h.
RW 24 LGwith 9 Lite Grille• R.O. 24 1/2” d.
RW 24 DGwith Diamond Grille
• R.O. 24 1/2” d.
LB 88• 2” Projection• 8” Height • 8” Width
LB 1414• 3 1/4” Projection• 14” Height • 14” Width
• GLASS NOT INCLUDED• 4 9/16” Jamb• Sold with/without Grilles• Inside Casing Included
ARCH 2031 QGwith Queen Anne Grille
• R.O. 20” w. x 31 3/8” h.
4 9/16”
3/4”
2 1/4”
LB 68• 1 3/4” Projection• 6 1/2” Height • 8” Width
ARB 3232• 4 5/8” Projection• 31 1/2” Height • 31 1/2” Width
• Can be ordered as a planton or for window glazing
DECORATIVEARABESQUE
LIGHTBLOCKS
SPECIALTYWINDOWS
Photo above illustrates the use of the decorative arabesque ARB 3232 and ceiling rosette CR 7.
136
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
PN 3600 • 1” Projection• 30 3/4” Height • 30 3/4” Width
PN 3600 • 1” Projection• 30 3/4” Height • 30 3/4” Width
PQ 3500• 2” Projection• 14 1/2” Height • 12” Width
PQ 3502• 5 1/4” Projection• 14” Height • 16 1/2” WidthPQ 3503• 5 1/4” Projection• 17 7/8” Height • 23” Width
PQ 3504• 1/2” Projection• 5 1/2” Height • 15 1/2” Width
RP 1612• 3” Projection• 12” Height • 16” Width
RP 1536• 9/16” Projection• 15” Height • 36” Width
RECESSED PANELS
CUSTOM SIZES AVAILABLE
PQ 3501• 3 1/4” Projection• 20 1/4” Height • 20 1/4” Width
Photo above illustrates the use of the following Spectis products: railings RAL 2100T & B, balusters BAL 2034, newel posts NP 2201 and newel caps NC 2311.
137
w w w . s p e c t i s . c o m
MISCELLANEOUS
RP 3906• 1 1/2” Projection • 24” Square
• Decorative Only• 2” Projection RP 3900• 28” SquareRP 3907• 22” Square
RP 3903 • 1 1/2” Projection • 32” Height• 10 1/2” WidthRP 3904 • 1 1/2” Projection • 21 1/2” SquareRP 3905• 1 1/2” Projection • 35 1/2” Height• 21 1/2” Width
WP 2432S• 24 1/2” Width • 32 1/2” Height WP 2832S • 28 1/2” Width • 32 3/4” Height WP 3229S • 32 5/8” Width • 29” Height
WP3729S • 37 1/2” Width • 29” HeightWP 3732S • 37 1/2” Width • 32 3/4” HeightWP 4432S • 44 1/2” Width • 32 3/4” Height
WP 1825 • 17 7/8” Width • 24 7/8” HeightWP 2730 • 27” Width • 30” Height
WP 4630• 46” Width • 30” HeightWP 6024• 60” Width • 24” Height
• With Sill
• With No Sill • 1” Projection
CUSTOM SIZES AVAILABLE
RP 3910• 2” Projection• 22 1/2” Height • 38” Width
WINDOW PANELS
RP 3909• 1” Projection • 38 3/4” Square
RECESSED PANELS
Photo above illustrates the use of the following Spectis products: custom window panel, balusters BAL 2059-18, and custom mantle.
138
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
FP 7248P• 1 1/4” Projection• 48” Height• Shaft • 5 1/4” Width• Plinth • 6 5/8” WidthFP 7254• 1 1/2” Projection• 54” Height
FP 7248M• 4 3/8” Projection• 76 7/8” Length
FP 7248C• 4 3/8” Projection
• Set of Three Pieces
FAC 13826L• 12/12 Pitch
FAC 13826R• 12/12 Pitch
11’ –
6 1
/4”
8’ – 4
3/4
”
2’ – 2 1/2”
11 3
/8”
7 13/18”
8”
FAC 18126L• 12/12 Pitch
FAC 18126R• 12/12 Pitch
11 5/16”
1’ – 6”
10’ –
6 7
/16”
9’ – 1
”
8”
FINISHINGAll Spectis’ products are shipped “double primed” with an exterior grade latex paint and are ready for use. We recommend final finishing after installation is complete for the most consistent appearance possible. Please see “finishing” recommendations (on page 233) for more information.
RAKE TRIM
FIREPLACE SURROUND
Photo above illustrates the use of the following Spectis products: fireplace plinths FP 7248P and custom header CSH 1015.
139
w w w . s p e c t i s . c o m
MISCELLANEOUS
Photo above illustrates the use of the following Spectis products: custom corner pilaster, custom size header CSH 1006, and oval trim OTK 3801-1624.
OT 3800 - 1824• 18” w. x 24” h.OT 3800 - 2030• 20” w. x 30” h. OT 3800 - 2335• 23 1/4” w. x 35 1/4” h.OT 3800 - 3346• 33 3/4” w. x 46” h.OT 3800 - 4052• 40” w. x 52” h.• 1 3/4” Projection• Inside Dimensions • Matches MD 1377
OTK 3801 - 1624• 16” w. x 24 1/2” h.OTK 3801 - 2948• 29 5/8” w. x 48” h. OTK 3801 - 3046• 30” w. x 46” h.OTK 3801 - 3656• 36” w. x 56 1/2” h.• 1 3/4” Projection• Inside Dimensions • Matches MD 1144• With Keystones
OTK 3800 - 1928• 19 3/4” w. x 28 1/2” h.OTK 3800 - 2436• 24” w. x 36” h. • 1 3/4” Projection• Inside Dimensions • Matches MD 1377• With Keystones
140
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
Beams are reinforced with an aluminum truss embedded in the polyurethane
Spectis’ trellis design incorporates the latest maintenance free technology with the traditional look of early 20th century architecture. Our trellis features a 100% maintenance free polyurethane exterior shell wrapping an internal aluminum structural truss, providing a 5-lb./ft2 safe loading. Our trellis is modular in design, but can be ordered as a 12' x 12' kit (TR 1212B). Each trellis comes with pre-notched beams and crosses for easy assembly.
Contact your Spectis Customer Service Representative for more information and custom sizes.
TRB103C 3” x 6” x 12’, no Aluminum Coped both endsTRB103A 3” x 6” x 12’, no Aluminum Coped one endTRB103B 3” x 6” x 12’, no Aluminum No coped ends (square ends)TRB101C 3” x 9” x 12’, with Aluminum Coped both endsTRB101A 3” x 9” x 12’, with Aluminum Coped one endTRB101B 3” x 9” x 12’, with Aluminum No coped ends (square ends)TRB100C 4” x 10” x 12’, with Aluminum Coped both endsTRB100A 4” x 10” x 12’, with Aluminum Coped one endTRB100B 4” x 10” x 12’, with Aluminum No coped ends (square ends)KIT100 Splice kit to join 9" and 10" beams together
TR1212A – Complete Trellis Kit contains9 – TRB103 3” x 6” Beams4 – TRB101 3” x 9” Beams4 – CLM100-106 with mounting flanges4 – CB100-144 Tuscan Cap4 – CB100-145 Tuscan Base4 – KIT101 Hardware to fasten Columns to both Trellis and Concrete Deck and flashing for Column Caps
TR1212B – Complete Trellis Kit contains9 – TRB101 3” x 9” Beams4 – TRB100 4” x 10” Beams4 – CLM100-106 with mounting flanges4 – CB100-144 Tuscan Cap4 – CB100-145 Tuscan Base4 – KIT101 Hardware to fasten Columns to both Trellis and Concrete Deck and flashing for Column Caps
CUSTOM SIZES AVAILABLECall for Quotation
See page 234 for trellis installation instructions.
NOTE : TRELLIS/ARBOR/PERGOLA
TR1212A
141
w w w . s p e c t i s . c o m
MISCELLANEOUS
Trellis parts can be used in a modular fashion so the trellis footprint can grow in either direction in multiples of 12’. Eg. 2 – TRB100As and 1 – TRB100B can be put together with splice kits to create a run of 36’, sup-ported by 4 columns.
TRELLIS/ARBOR/PERGOLA
Photo right and below illustrate the use of different custom Spectis trellis installations.
142
1 • 8 0 0 • 6 8 5 • 9 9 8 1
MISCELLANEOUS NOTICE :
PL PREMIUM ADHESIVE MUST BE USED ON ALL BEDDING/BUTT JOINTS.
Closed Louvre • 1 1/4” Projection SHL-1-1872 • 18” Width • 72” Height SHL-1-3696 • 36” Width • 96” Height
SHL-2 1449 • 14” w. x 49” h. SHL-2 1459 • 14” w. x 59” h. SHL-2 1645.5 • 16” w. x 45 1/2” h. SHL-2 1647 • 16” w. x 47 1/2” h. SHL-2 1648 • 16” w. x 48” h. SHL-2 1769 • 17” w. x 69” h. SHL-2 1837 • 18” w. x 37” h. SHL-2 1842 • 18” w. x 42” h. SHL-2 1848 • 18” w. x 48” h. SHL-2 1855 • 18” w. x 55” h. SHL-2 1860 • 18” w. x 60” h. SHL-2 1864 • 18” w. x 64” h. SHL-2 1867 • 18” w. x 67” h. SHL-2 1872 • 18” w. x 72” h. SHL-2 1876 • 18” w. x 76” h. SHL-2 1878 • 18” w. x 78” h. SHL-2 1881 • 18” w. x 81” h. SHL-2 1896 • 18” w. x 96” h. SHL-2 2062 • 20” w. x 62” h. SHL-2 2448 • 24” w. x 48” h. SHL-2 2460 • 24” w. x 60” h.
• 1 1/4” Projection • 1 Raised Panel
SHP-1 1624• 16” w. x 24” h.
• 1 1/8” Projection • Arched Raised Panel
SHA 1890R • 18” w. x 90” h.SHA 1890L • 18” w. x 90” h.
SHP-2 928 • 9” w. x 28” h. SHP-2 1371 • 13” w. x 71” h. SHP-2 1457 • 14” w. x 57 1/2” h. SHP-2 1460 • 14” w. x 60” h. SHP-2 1472 • 14” w. x 72” h. SHP-2 1635 • 16” w. x 35” h. SHP-2 1639 • 16” w. x 39” h. SHP-2 1647 • 16” w. x 47” h. SHP-2 1647.5 • 16” w. x 47 1/2” h. SHP-2 1651 • 16” w. x 51” h. SHP-2 1655 • 16” w. x 55” h. SHP-2 1659 • 16” w. x 59” h. SHP-2 1663 • 16” w. x 63” h. SHP-2 1667 • 16” w. x 67” h. SHP-2 1671 • 16” w. x 71” h. SHP-2 1675 • 16” w. x 75” h. SHP-2 1677 • 16” w. x 77” h. SHP-2 1681 • 16” w. x 81” h. SHP-2 1686 • 16” w. x 86” h. SHP-2 1872 • 18” w. x 72” h. SHP-2 2056 • 20” w. x 56” h. SHP-2 2454 • 24” w. x 54” h. SHP-2 2472 • 24” w. x 72” h. SHP-2 2492 • 24” w. x 92” h. SHP-2 2472-4 • 24” w. x 72 3/8” h. • 4" rail
CUSTOM SIZES AVAILABLERaised panel PVC shutters
can be custom ordered
SHP-3 1472 • 14” w. x 72 1/4” h. SHP-3 1635 • 16” w. x 35” h. SHP-3 1639 • 16” w. x 39” h. SHP-3 1647 • 16” w. x 47” h. SHP-3 1651 • 16” w. x 51” h. SHP-3 1655 • 16” w. x 55” h. SHP-3 1659 • 16” w. x 59” h. SHP-3 1663 • 16” w. x 63” h. SHP-3 1667 • 16” w. x 67” h. SHP-3 1671 • 16” w. x 71” h. SHP-3 1675 • 16” w. x 75” h. SHP-3 1677 • 16” w. x 77” h. SHP-3 1681 • 16” w. x 81” h. SHP-3 1686 • 16” w. x 86” h. SHP-3 1839 • 18” w. x 39” h. SHP-3 1842 • 18” w. x 42” h. SHP-3 1848 • 18” w. x 48” h. SHP-3 1852 • 18” w. x 52” h. SHP-3 1855 • 18” w. x 55” h. SHP-3 1862 • 18” w. x 62” h. SHP-3 1864 • 18” w. x 64” h. SHP-3 1865 • 18” w. x 65” h. SHP-3 1867 • 18” w. x 67” h. SHP-3 1877 • 18” w. x 77” h. SHP-3 1896 • 18” w. x 96” h.
• 1 1/4” Projection • 3 Raised Panels
• 1 1/4” Projection • Closed Louvre
• 1 1/4” Projection • 2 Raised Panels
SHL-1-3696
SHUTTERS