of 16
8/9/2019 MIST Maxsurf Training Day-4
1/16
Training on
MaxsurfDay-4
S.M. RashidulHasan
Naval Architect
8/9/2019 MIST Maxsurf Training Day-4
2/16
Edit si!le sha!es.
"se of tri in di#erent $ays.
Ma%e a transverse !artition.
Ma%e a circular hole.
Ma%e a rectangular o!ening.
Agenda
8/9/2019 MIST Maxsurf Training Day-4
3/16
"se of axsurf in details
Di#erent ethods to odify and u!dateodels
&earning 'utcoe
8/9/2019 MIST Maxsurf Training Day-4
4/16
Tri si!le sha!e
8/9/2019 MIST Maxsurf Training Day-4
5/16
Tri si!le sha!e
'!en last saved odel after co!leting the tas%.
(o to surfaces)add surface)transverse !lane*
nae it TS-+ Move TS-, longitudinally to -+
(o to dis!lay)triing. Select triing invisile
(o to surface)start triing and select the
surface you $ant to e tried o# /here it is TS-+0
Select the !art to e tried o# fro the ne$lyshaded area y a si!le clic%.
(o to surface)tri TS-+ or ctrl1t
8/9/2019 MIST Maxsurf Training Day-4
6/16
Tri si!le sha!e
The transverse !lane is tried o#. 2ou canchec% $hether it is !ro!erly tried or not.
(o to surface)delete surface* select HS-+2ou can see the after tried surface. "ndo
the last coand to restore HS-+.
3hat can this ne$ly tried surface in
shi!
8/9/2019 MIST Maxsurf Training Day-4
7/16
Tri si!le sha!e
8/9/2019 MIST Maxsurf Training Day-4
8/16
Tri si!le sha!e
(o to surface)add sha!e)cylinder
Select transverse orientation* change r, 5 r+ to 6.
Move cylinder /to! 5 otto0 to longitudinally ,7and vertically -,
Rotate the !ers!ective vie$ a suitale !osition totri.
Dis!lay)triing* select triing o# if not selected
Surface)start triing)&S-+
8lic% the &S-+ inside the cylinder.
Surface)tri &S-+ or ctrl1t
8/9/2019 MIST Maxsurf Training Day-4
9/16
Tri si!le sha!e
No$ $e have to tri the cylinder against theain ody.
(o to surface)start triing)cylinder otto.8lic% cylinder otto fro the shaded !art.8trl1t
(o to surface)start triing)cylinder to!.
8lic% cylinder to! fro the shaded !art. 8trl1t. See the hole you ade9 3hat it can e in shi!
8/9/2019 MIST Maxsurf Training Day-4
10/16
Tri si!le sha!e
(o to edit)select)select all. :ress ctrl1u toungrou! any grou!ed 8:.
(o to !ro;le vie$. Select all !oints at the otto left corner. :ress
ctrl1g
Doule clic% the grou! and change the height to
-, (o to !ers!ective vie$. 3hat can you see and
$hy
Do the triing of TS-+ again.
8/9/2019 MIST Maxsurf Training Day-4
11/16
Tri si!le sha!e
8/9/2019 MIST Maxsurf Training Day-4
12/16
Tri si!le sha!e
Add a transverse !lane* nae it TS-7
Siisuali
8/9/2019 MIST Maxsurf Training Day-4
13/16
Tri si!le sha!e
(o to !ro;le* select all ne$ly fored surface8:s. :ress ctrl1g
Doule clic% any otto 8: of the ne$ grou!*give height to +.
"ngrou! all.
Tri the surface inside the rectangle.
Tri the rectangle as $ell /if you don?t seeyour desired surface clic% on ore surface tosee all0
8/9/2019 MIST Maxsurf Training Day-4
14/16
Add a!!endage
8/9/2019 MIST Maxsurf Training Day-4
15/16
Add a!!endage
Surfaces)add surface)NA8A,
Move NA8A, to -, nuerically
8hange the si
8/9/2019 MIST Maxsurf Training Day-4
16/16
Add a!!endage
Tas%B Ma%e rectangle hole at the side shell