Instruction ManualMP011

Mobile Hydraulic Scissor Lift Table2200 lbs. (1000 kg)

WARNING!Read this operation manual carefully and understand fully the operating instructions. Improper use of this unit could result in injury.

• DO NOT put foot or hand in scissor mechanism.• Keep neighbouring persons away from the unit when in use.• DO NOT stand in front or behind of lift table when it is in use.• DO NOT crawl under the table.• DO NOT put foot in front of rolling wheels.• DO NOT use lift table on slope or inclined surfaces. • DO NOT lift or ride people on this unit.

CAUTION!• DO NOT move this unit when lifting or lowering the bed or when the bed is in an elevated position. (Bed must be lowered when the unit is running)• DO NOT use this table for any purpose other than it’s intended use and do not load with more than the rated capacity.• DO NOT allow persons to operate this table without complete understanding of its operation.• DO NOT lower the bed too quickly.• During loading/unloading operation, do not release the parking brake.• Load should be distributed on at least 80% of the table area. Stop operation of lift table if load becomes too unstable, do not place objects protruding off edge of the bed.• DO NOT modify lift table without manufacturers written consent.

Daily InspectionDaily inspection of this unit is critical in order to locate any malfunction or fault. Check the following daily before operating your lift table.

1. Check for bending or cracking of the lift table.2. Check for any oil leakage from the cylinder.3. Check for vertical creep of the table.4. Check for smooth movement of the wheels.5. Ensure that brakes are fully functional.6. Ensure that all nuts and bolts are firmly tightened.

Assembly methodThe lift table is packed in a cardboard box. Assembling of the jack up pedal is required.WARNING: Assembly work must be done on a flat surface; wheels must be choked to prevent accidental rolling of the unit.

1. Insert the jack pedal into the pedal pipe and position the tapered side pedal end to right. Tighten the jack pedal using the removed nut and washer with the smallest hex key supplied in the box.

OPERATING THE LIFT TABLE

How to use the brakeThe brake is located next to the swivel caster on right hand side.1. To brake the lift table, press the brake pedal.

2. To release the brake, lift up the brake pedal.

CAUTION: Put lift table in brake mode when stationary in order to prevent sudden movement.

Lifting the TableTo lift the table, press the lifting pedal several times until the table reaches the desired height. The table

lowers slightly after reaching the highest position. Maximum Capacity of this table is 2200 lbs. (1000 kg).WARNING: Do not overload lift table, stay within the rated capacity.Do not load the table on sides or ends only. Load must be distributed on at least 80% of table area.

Lowering the TableWARNING: DO NOT put foot or hand in scissor mechanism. The rotating knob lowers the table.NOTE: The hydraulic cylinder is designed to hold table. As is the nature of the hydraulic system, table lowers very slowly over an extended period of time. Please note that the table does not stay at the same height indefinitely.

Specifications

Model Capacity TableTable

HeightFoot Pedal

Strokes to ElevateWheel Weight

MP0111000 kg.2200 lbs.

515 x 1016 mm20.2" x 40"

380-1000 mm14.9" x 39.3"

≤55150 mm

5.9"115 kg.253 lbs.

Service InstructionsChange hydraulic oil every 12 monthsLubricate the following areas every month: Fitting of Cylinder/oil, Roller Friction Surface/grease, Link Pin/oil, Pedal Fitting Point/oil, Grease Nipple/grease

TroubleshootingIf the table does not lift when pressing the lift pedal several times:The pull rod is too loose and needs to be tightened.• Using a wrench, loosen the nut holding the pull rod in place.• With pliers, pull the end of the pull rod to tighten it, and then use a wrench to tighten the nut.

If the table does not lower:The pull rod is too tight and needs to be loosened.• Using a wrench, loosen the nut holding the pull rod in place. • With pliers, push the pull rod from the end back to loosen it, then a wrench to tighten the nut.

LIFT TABLE PARTS LIST

PartNo.

ModelNo. Description Qty.

2 SPB90.1.01 Handle bar 1

3 SP70.0-15 Rod 1

4 SP70.0-14 Cam 2

5 SP70.0-13 Retaining ring 1

6 SPB90.0-02 Pedal 1

7 GB77-85 Screw 3

8 GB41-86 Nut 4

9 SP70.0-11 Nut 4

10 SPA.0-02 Washer 2

11 GB93-1986 Washer 2

12 GB5781-2000 Bolt 2

13 GB/T276-94 Bearing 2

14 SP70.0-10 Bush 2

15 GB297-64 Bearing 2

16 GB5781-2000 Bolt 2

17 GB41-86 Nut 2

18 GB95-1985 Washer 1

19 SP70.7-01 Spring 1

20 SPB90.7.02 Rack wheel 1

21 SP70.7.02 Brake piece 1

22 GB894.1-86 Retaining ring 8

23 SP70.0-05 Shaft 4

24 SP70.0-04 Washer 4

25 GB/T276-94 Bearing 8

26 SP70.0-03 Wheel 4

27 GB5781-2000 Bolt 1

28 SPB90.0.01 L-pin 1

29 SPB90.3-00 Frame 1

30 SPB90.6-00 Pump 1

31 SP.0-11 Shaft 1

32 SP.0-12 Bush 1

33 GB894.1-86 Retaining ring 1

34 GB70-85 Screw 1

35 GB93-1986 Washer 3

36 GB894.1-86 Retaining ring 4

37 YQ-7-700 Retaining ring 1

38 SP70.0-07 Shaft 1

39 SPB90.2.1 Pedal rod 1

40 SP.3-03 Cushion 1

41 GB894.1-86 Retaining ring 4

A

B

PartNo.

ModelNo. Description Qty.

42 SPC70.4-13 Roller 4

43 GB5781-2000 Bolt 1

45 SP70.0-01 Shaft 1

46 SPB90.4-00 Arm 1

48 SPB90.5-00 Table 1

49 SP.3-02/-01 Pedal bar 1

51 GB95-1985 Washer 1

58 YQ-8-700 Retaining ring 1

59 SPA70.7-02 Washer 4

A MP026 Rigid wheel assembly 2

B MP023 Swivel wheel assembly 2

PUMP PARTS LIST

PartNo.

ModelNo. Description Qty.

PartNo.

ModelNo. Description Qty.

PartNo.

ModelNo. Description Qty.

1 GB3452.1-86 O-ring 1 19 SP.8-17 Spring 1 37 SP70.6-07 Washer 1

2 SP.8-11 Pump cylinder 1 20 SP.8-16 Adjusting screw 1 38 GB3452.1-82 O-ring 1

3 UHS18 YX-seal ring 1 21 GB3452.1-86 O-ring 2 39 SP70.6-08 Cup packing 1

4 DH18 Dust seal 1 22 SP.8-15 Cover ring 1 40 SP70.6-09 Bush 1

5 SP.8-10 Pump plunger 1 23 GB308-77 Steel ball 1 41 GB3452.1-82 O-ring 1

6 SP.8-09 Spring 1 24 SP.8-07 Spring 1 42 SPB90.6-02 Piston rod 1

7 SP.8-08 Spring seat 1 25 GB308-77 Steel ball 1 43 S70.6-01 Cylinder cap 1

8 GB894.1-86 Retaining ring 1 26 GB77-85 Screw 1 44 GB3452.1-82 O-ring 1

9 SP70.0-09 Joint plate 2 27 YQ-01A Strike pin 1 45 HG4-692-67 J shaped steel frame rubber sealing 1

10 SP.0-14 Pin 1 28 GB3452.1-82 O-ring 2 46 YQ.6-700 Base 1

11 JF.1-17 Plug 1 29 DF1.2-08 Shaft 1 47 YQ-04 Lever plate 1

12 JB982-77 Copper washer 1 30 Filter 1 48 GB894.1-86 Retaining ring 1

13 6W804.1-12 Damp valve 1 31 GB3452.1-82 O-ring 2

14 YQ-03A Spring 1 32 SP70.6-06 Rectangular section ring 1

15 YQ-02 Spring seat 1 33 SPB90.6-01 Cylinder 1

16 GB308-77 Steel ball 2 34 SP70.6-02 Housing 1

17 GB308-77 Steel ball 1 35 SP.8-02 Screw 1

18 SP.8-18 Spring seat 1 36 GB894.1-86 Retaining ring 1

HANDLE PARTS LIST

PartNo.

ModelNo. Description Qty.

1 GB879-86 Spring pin 1

2 SPB90.1.01 Handle bar 1

3 MP015 Knob 1

4 GB6172-86 Nut 1

5 SPIII.0-01 Screw 1

6 MP019 Pull rod 1