Mobile Soft Switch Solution in BC

Mobile Softswitch Solution (MSS) R6.1 Training Programs

Catalog of Course Descriptions

Page 2

Catalog of Course Descriptions

AXE EMERGENCY HANDLING ..........................................................................................6

MSS VOIP INTERWORKING ...............................................................................................9

SIGNALING IN THE CORE NETWORK - CLASSICAL ARCHITECTURE ......................11

SIGNALING IN THE CORE NETWORK - MOBILE SOFTSWITCH SOLUTION ............15

MSC-S R 14.1 BLADE CLUSTER OVERVIEW – WBL ....................................................18

SIP/SIP-I IN MSS R6 ..........................................................................................................20

MSS PERFORMANCE MANAGEMENT ...........................................................................22

BLADE CLUSTER DATA TRANSCRIPT WORKSHOP ...................................................25

A-INTERFACE OVER IP IN MSS .....................................................................................27

MSC-S R14.0 TO R14.1 BLADE CLUSTER CONFIGURATION DELTA ........................31

MSS R6.1 NETWORK PLANNING AND HARDWARE DIMENSIONING ........................33

MSS TROUBLESHOOTING ..............................................................................................36

MSC-S R14.1 BLADE CLUSTER OVERVIEW .................................................................39

MSS R6.1 SURVEY ...........................................................................................................41

BLADE CLUSTER PLATFORM OPERATION AND MAINTENANCE .............................43

MSC/MSC-S R14.1 DATA TRANSCRIPT ........................................................................46

MSC–S R14.1 CONFIGURATION DELTA ........................................................................50

MSC/MSC-S R14.1 CONFIGURATION .............................................................................53

218/038 19-FAP 130 506 Rev: A

Commercial in Confidence 2

Ericsson ABGlobal Services

SE-164 80 StockholmTelephone: +46 8 757 0000

Email: [email protected] www.ericsson.com/globalservices

© Ericsson AB 2010

http://www.ericsson.com/globalservices

Page 3

MSC/MSC-S R14.1 FEATURES DELTA ..........................................................................57

MSC-S R13.2 TO R14.1 BLADE CLUSTER CONFIGURATION DELTA .......................59

M-MGW R6.1 DELTA ........................................................................................................62

M-MGW R6.1 OPERATION AND CONFIGURATION .....................................................64

M-MGW OPERATION WITH AMOS .................................................................................67

SIGTRAN WORKSHOP ....................................................................................................70

GSM/WCDMA MSC IN POOL INTRODUCTION ..............................................................73

APZ 212 55 OPERATION AND MAINTENANCE..............................................................76

APZ 212 60 OPERATION AND MAINTENANCE..............................................................79

AXE 810 DATA TRANSCRIPT ..........................................................................................82

AXE810 MAINTENANCE ...................................................................................................86

GSM AXE OPERATION .....................................................................................................89

GSM MAINTENANCE MSC/BSC EXTENDED..................................................................92

WCDMA AXE OPERATION ...............................................................................................96

WCDMA MAINTENANCE MSC EXTENDED.....................................................................99

IS 3.1 OVERVIEW.............................................................................................................103

IS 3.1 OPERATION AND CONFIGURATION .................................................................105

IU OVER IP IN MSS .........................................................................................................109

M-PBN 2010A CONCEPTS - CIRCUIT SWITCHED - SMARTEDGE TRACK ..............111

M-PBN 2010A CONCEPTS - CIRCUIT SWITCHED - JUNIPER TRACK ......................114

218/038 19-FAP 130 506 Rev: A





© Ericsson AB 2010


Page 4

IP NETWORKING ............................................................................................................118

IP QUALITY OF SERVICE AND MPLS............................................................................121

IP SECURITY ...................................................................................................................123

IPV6 NETWORKING ........................................................................................................127

IPV6 QUALITY OF SERVICE .........................................................................................130

IPV6 ROUTING ................................................................................................................132

IPV6 SECURITY ...............................................................................................................134

CPP NODE FEATURES AND FUNCTIONS ...................................................................136

TFO/TRFO INTERWORKING INTRODUCTION ...........................................................139

APG43 DELTA .................................................................................................................141

APG43 OPERATION AND MAINTENANCE ...................................................................143

APG43 RECOVERY PROCEDURES ..............................................................................147

APG43 INSTALLATION AND CONFIGURATION ..........................................................150

218/038 19-FAP 130 506 Rev: A





© Ericsson AB 2010


Page 5

IntroductionEricsson has developed a comprehensive Training Programs service to satisfy the competence needs of our customers, from exploring new business opportunities to expertise required for operating a network. The Training Programs service is delineated into packages that have been developed to offer clearly defined, yet flexible training to target system and technology areas. Each package is divided into flows, to target specific functional areas within your organization for optimal benefits.

Service delivery is supported using various delivery methods including:

Icon Delivery Method

Instructor Led Training (ILT)

Seminar (SEM)

Workshop (WS)

Virtual Classroom Training (VCT)

Web Based Learning (WBL)

Short Article (SA)

Streaming Video (SV)

CD-ROM (CD)

Structured Knowledge Transfer (SKT)

Delivery Enablers

Remote Training Lab (RTL)

Web Portal (WP)

Ericsson Education E-Learning

EEOnline @ http://learning.ericsson.net/eeonline/

218/038 19-FAP 130 506 Rev: A





© Ericsson AB 2010


http://learning.ericsson.net/eeonline/

AXE Emergency Handling

LZU 108 094 R3A

Description

Are you prepared for an emergency situation?

This course provides the students with the knowledge required to recover the AXE from fault situations in critical parts, including stoppages in the Central Processor.

Learning objectives

On completion of this course the participants will be able to:

1 Handle a CP stoppage1.1 Restart / Reload the CP with normal commands1.2 Restart / Reload the CP with CPT commands1.3 Reload the CP without using commands1.4 Test and repair the CP using CPT commands1.5 Give 2 examples of a cause for a stoppage1.6 Interpret an Error Interrupt Printout

2 Handle RPB-S and RPB-E faults2.1 Find an RP using branch, magazine and slot number2.2 Find the equipment controlled by an RP2.3 Repair an RPB-S fault2.4 Disconnect the RPB-S from an APT magazine without causing disturbances for other

magazines2.5 Repair an RPB-E fault2.6 Disconnect the RPB-E from an APT magazine without causing disturbances for other

magazines

3 Handle GS faults for AXE 103.1 Find the TSM, SPM, CLM boards3.2 Distinguish between DL3, RP and EM Bus cables3.3 Calculate the number of traffic channels in a TSM3.4 Repair a GS fault without disturbing the traffic

4 Handle GS faults for AXE 8104.1 Find the XDB, DLEB and DLHB boards4.2 Locate the DL2, DL3,DL34, and DL5 links4.3 Calculate the number of traffic channels in XM-0-04.4 Repair a GS fault without disturbing the traffic

5 Handle problems in the APG 40

6

5.1 Perform a backup of the APG software5.2 Follow the OPI to make a trouble report5.3 Perform a Restore on the APG

Target audience

The target audience for this course is: System Engineer.

Prerequisites

The participants should be familiar with Operation and Maintenance of nodes based on AXE.

Successful completion of the following courses:

• AXE 810 Maintenance – LZU 108 6750

• WCDMA AXE Operation – LZU 108 5024/1 or GSM AXE Operation – LZU 108 5024/2

• WCDMA Maintenance MSC Extended – LZU 108 5031/1 or GSM Maintenance MSC/BSC Extended – LZU 108 5031/2

• APG40 Operation and Maintenance – LZU 108 6567

Duration and class size

The length of the course is 5 days and the maximum number of participants is 8.

Learning situation

The course is intructor led Training (ILT). The main time is spent on practical group work exercises, using AXE exchanges and tools.

218/038 19-FAP 130 506 Rev: ACommercial in Confidence




© Ericsson AB 2010


Time schedule

The time required always depends on the knowledge of the attending participants and the hours stated below can be used as estimate.

Day Topics in the course Estimated time1 Lesson: CP HW units and buses

Lesson: Manual recovery proceduresLesson: RPB-S & RPB-EExercise: Serial RP Bus

3 hours1 hour1 hour1 hour

2 Lesson: CP HW fault handlingExercise: Error Interrupt printoutExercise: CP stoppage

1 hour1 hour4 hours

3 Lesson: CP SW fault handlingExercise: CP stoppageExercise: Ethernet RP Bus

1 hour3 hours2 hours

4 Exercise: CP stoppageExercise: GS HW layout & fault handling

2 hours4 hours

5 Exercise: AP Backup 2 hoursExercise: AP Trouble Report 1 hourExercise: AP Restore 3 hours





© Ericsson AB 2010


MSS VoIP Interworking

LZU 108 6815 R4A

Description

This course is designed to provide competence on VoIP Interworking in MSS (MSS to IMS via SIP and MSS to other Softswitch via SIP-I). The course outlines the VoIP implementation in MSS as well as connection scenarios with IMS and other Softswitch networks. It does not only cover concepts but also guides on implementation. Configuration parameters and Data Transcript, physical connections and statistics related to VoIP transport / signaling are presented. SIP and SIP-I signaling knowledge is a prerequisite for this course and those new to SIP is expected to attend the “SIP/SIP-I in MSS R6” course beforehand.

Learning objectives


1 Explain the IP Connectivity support in MSC-S R141.1 Illustrate the BC platform and the BC internal signaling interface for SIP.1.2 List the main steps in setting up L2 infrastructure for SIP1.3 Describe the IP stack on CP implementation1.4 Explain the supervision and failover mechanisms for the IP layer1.5 Explore important issues related to the Packet Backbone Network

configuration for SIP

2 Explain the VoIP Interworking principles in MSS R62.1 Describe the MediaGateway Control Function (MGCF) capabilities of the MSC-S2.2 Describe the routing for VoIP calls and telephone number handling 2.3 Explain the usage and configuration options of DNS in MSC-S2.4 State two solutions for handling failover of VoIP calls in the system2.5 Understand Codec handling for VoIP calls2.6 Describe handling of Interlink Connections2.7 Name two alternatives for transport of DTMF/Tones in VoIP calls2.8 Relate the main steps in the setup of a VoIP call

3 Explain the steps in Configuration of VoIP3.1 Describe the SIP/SIP-I route concept as implemented in MSC-S3.2 Make clear the meaning of the RSI, SCI and EIVP parameters3.3 List the 3 main steps in the MGCF configuration for SIP/SIP-I3.4 List and explain the DT for SIP/SIP-I 3.5 List and explain the DT for SIP-I Screening

9

Target audience

The target audience for this course is: Network Design Engineer, Service Design Engineer, System Technician, System Engineer and Network Deployment Engineer.

This audience includes personnel in charge of the operation or engineering of these nodes, who require specific knowledge of the operation of Ericsson's Core Network.

Prerequisites

Successful completion of the following course:

SIP/SIP-I in MSS R6 LZU 108 7688 R1A



Learning situation

This course is based on theoretical instructor-led lessons given in a classroom environment.

Time schedule


Day Topics in the course Estimated time

1 IP Connectivity 1,5 hour

VoIP Interworking 2.5 hours

Configuration of VoIP 2 hour




www.ericsson.com/globalservices© Ericsson AB 2010


Signaling in the Core Network - Classical Architecture

LZU 108 7518 R2A

Description

Do you want to extend your understanding of Signaling Number 7?

This course provides a great opportunity to explore the mains protocols used in GSM and WCDMA networks.

The participants will analyze technologies and protocols used to manage and control voice calls in the Core Networks for WCDMA systems and GSM up to the release MSC R14.1 / MSS R6.1. The theoretical background will provide a better understanding for the Core Network in general and signaling specifically.

Learning objectives


1 Explain the basic structure and terminology of the Signaling System No. 7 1.1 Explain the terms Subscriber Loop Signaling, Inter-Exchange Signaling, Channel

Associated Signaling, and Common Channel Signaling1.2 Explain the basic functions of OSI reference model layers and the relationship

between the model and Signaling System No.71.3 Draw and explain the basic structure of Signaling System No.7 and list at least three

application-layer protocols1.4 List and explain common network terminology used to describe network elements and

the links between them

2 Describe the role of MTP in the Core Network2.1 List the major functions of the Message Transfer Part (MTP)2.2 Explain the structure and functions of all MTP signal units (MSU, LSSU & FISU) and

explain the function of all fields in the signal units2.3 Explain the error control and signaling link supervision mechanisms2.4 Explain the routing and load sharing of MTP signal units2.5 Explain the network management functions and their influence on signaling traffic

handling2.6 List at least two different types of Ericsson signaling terminals and explain their

connection in the AXE switch

3 Describe how signaling transport is handled in ATM networks3.1 Detail the broadband signaling transport architecture for ATM connectivity layers3.2 Describe how MTP-3B messages differ from MTP3 messages

4 SIGTRAN (New Chapter)4.1 Present the role and function of SIGTRAN in the Classical Solution

11

4.2 Describe the concepts behind SS7 Signaling transport over IP4.3 Explain terminology, related to SIGTRAN, relevant for the Ericsson implementation4.4 Describe the function of the Stream Control Transmission Protocol (SCTP) in

SIGTRAN 4.5 Describe the function of MTP3 User Adaption Layer (M3UA) in SIGTRAN 4.6 Describe the function of SCCP User Adaption Layer (SUA) in SIGTRAN

5 Describe ISUP signaling capabilities in good level, and list the messages of a typical call setup

5.1 List the major functions of the ISDN User Part (ISUP)5.2 List at least five messages used in typical call set-up cases and describe their

functions

6 Explain SCCP services and routing alternatives used by RANAP, BSSAP and MAP6.1 List the major functions of the Signaling Connection Control Part (SCCP)6.2 Describe the general structure of SCCP messages and explain the meaning of typical

fields in SCCP messages6.3 Explain the principles of routing of SCCP messages6.4 List which SCCP address information can be used for routing6.5 Describe briefly the SCCP management procedures

7 Describe signaling for a call setup towards a GSM radio access network7.1 List the major functions of the Base Station System Application Part (BSSAP)7.2 Identify and describe BSSAP specific terminology7.3 List at least five BSSAP operations used in typical call set-up and location updating

cases, and describe their functions and contents

8 Describe signaling for a call setup towards a WCDMA radio access network8.1 List the major functions of the Radio Access Network Application Part (RANAP)8.2 Identify and describe RANAP specific terminology8.3 List at least five RANAP operations used in typical call set-up and location update

traffic cases and describe their functions

9 Describe TCAP signaling principles on high level9.1 List the major functions of the Transaction Capabilities Application Part (TCAP)9.2 Explain the structure and coding principles of TCAP messages

10 Describe MAP signaling principles on high level10.1 List the major functions of the Mobile Application Part (MAP)10.2 List at least three MAP operations (messages)used in typical call set-up and location

updating cases, and describe their functions and contents10.3 Show the changes of MAP operations (messages) in successful Mobile-terminate

short message transfer (SMS)10.4 Show the changes of MAP operations messages in successful Mobile-originated SMS10.5 Describe how MAP v2 and v3 can be extended without losing compatibility10.6 Describe the principles used for the MAP version selection






11 CAMEL (New chapter)11.1 The purpose of this chapter is provides an overview of the different phases of CAMEL

with the main focus in CAMEL phase 2.11.2 Show the call set-up of a pre-paid subscriber making a call.

Target audience

System Technician, System Engineer, Network Design Engineer and Network Deployment Engineer

This audience will derive advantage from a deep insight about protocols and signaling techniques in the Mobile Core Network.

Prerequisites

Successful completion the following course:

GSM/WCDMA MSC/MSC-S R13.2 Configuration, LZU 108 7513

or equivalent competence.



Learning situation

This course is based on theoretical instructor-led lessons and theoretical exercises.






Time schedule


Day Topics in the course Estimated time1 SS7 Intro

MTPSAALSIGTRAN

1 hour2 hours2 hours1 hour

2 ISUPSCCPBSSAPRANAP

1 hours2 hours2 hours1 hour

3 TCAPMAPCAMEL

1 hour2 hours

2 hours






Signaling in the Core Network - Mobile Softswitch Solution

LZU 108 7519 R3A

Description

The complexity of the Core Network and the call control signaling has increased with the introduction of Softswitch Solutions, Bearer Independent Call Control and options for IP-based transmission. This course explains the general principles of call and bearer control in the Mobile Softswitch Solution (MSS) for WCDMA systems and GSM up to the release MSC R14.1 / MSS R6.0 The participants will get insight about related protocols, such as SS7 over IP,SUA, BICC, Q.2630, GCP, IPBCP and SIP. It is assumed that the students are already familiar with signaling in core networks with classical architecture before attending this course.

Learning objectives

1 Describe signaling handled by MSC server for setting up and releasing calls and bearers in the Mobile Softswitch Solution

1.1 Explain the horizontally integrated network model for the next generation Mobile Core Networks, the so called Mobile Softswitch Solution (MSS)

1.2 Explain what is meant by “Monolithic architecture” and “Layered architecture”1.3 List the protocols used in the Mobile Core Network and briefly describe their function1.4 List the user plane protocol stacks in the Core Network 1.5 List the possible transport layer technologies and discuss their use in the Mobile Core

Network

2 Present the role and function of SIGTRAN in the Mobile Softswitch Solution2.1 Describe the concepts behind SS7 Signaling transport over IP2.2 Explain terminology, related to SIGTRAN, relevant for the Ericsson implementation2.3 Describe the function of the Stream Control Transmission Protocol (SCTP) in

SIGTRAN 2.4 Describe the function of MTP3 User Adaption Layer (M3UA) in SIGTRAN 2.5 Describe the function of SCCP User Adaption Layer (SUA) in SIGTRAN

3 Explain BICC signaling principles and concepts3.1 Explain the role of BICC in a Multi-Service Network3.2 Explain how BICC relates to the ISDN User Part (ISUP)3.3 List and describe new terminology pertaining to BICC3.4 Diagrammatically represent the BICC Network model3.5 Explain the structure of BICC and its support protocols3.6 Describe the purpose and structure of Signaling Transport Converters (STCs)3.7 Explain a typical call set-up procedure using BICC3.8 Explain the difference between the BICC and the ISUP Message Signaling Unit

15

4 Explain Q2630 signaling principles and concepts4.1 Explain the purpose and significance of ATM Adaptation Layer 2 (AAL2)4.2 Describe the AAL2 network architecture4.3 List the capabilities and limitations of Q.2630 signaling4.4 Describe the interworking between BICC and Q.2630 in the Mobile Core Network

5 Explain GCP signaling principles and concepts5.1 Explain the Connection Model encompassing Contexts, Terminations and streams5.2 List H.248 Commands and Descriptors5.3 Explain the use of transactions and how commands are carried5.4 Explain how packages are used to expand the Termination Capabilities5.5

6 Explain IPBCP signaling principles and concepts6.1 Explain the establishment of IP bearers to transport speech6.2 Explain the tunneling principles used to establish an IP bearer

7 Describe the steps in a typical Circuit Mode call set up and explain how the involved signaling protocols interact

7.1 List some parameters that are transported between nodes during the call set-up7.2 Describe the interworking between BICC, GCP, Q.2630, RANAP/NAS and ISUP in a

typical call set-up

8 Present how SIP and related support protocols for VoIP are applied in the Mobile Softswitch Solution

8.1 Describe the basic functions and capabilities of SIP8.2 Name major IETF protocols related to SIP, IMS and VoIP8.3 List the SIP methods used in MSS and state their function8.4 Explain the routing and addressing principles for SIP signaling8.5 Explain the offer / answer model for SDP usage in SIP8.6 Describe how SIP-I relates to BICC/ISUP and SIP8.7 Explain the steps in a basic session establishment between MSS and an external

VoIP network

Target audience

System Technician, System Engineer, Network Design Engineer and Network Deployment Engineer

This audience benefits from a deep insight about protocols and signaling techniques in the Mobile Core Network.






Prerequisites


Signaling in the Core Network – Classical Architecture, LZU 108 7518

and

GSM/WCDMA MSC/MSC-S R13.2 Configuration, LZU1087513

or equivalent competence.



Learning situation


Time schedule


Day Topics in the course Estimated time11

1/2

Core Network signaling introductionSIGTRANBICC

1.5 hours2.5 hours3 hours

22/3

Q2630 GCP

2 hours4 hours

3 traffic case Interworking, (BICC, GCP, Q2630)IPBCPSIP

0.5 hours1.5 hours3 hours






MSC-S R 14.1 Blade Cluster Overview – WBL

LZU 108 7682 R2A

Description

What is an MSC Server Blade Cluster? What benefits does it bring to the operator?

The MSC Server Blade Cluster Overview answers these questions. The course provides an introduction to the MSC Server Blade Cluster, its features, and describes the benefits for the operator.

Learning objectives

1 Recognize the MSC Server Blade Cluster Components

2 Explain the MSC Server Blade Cluster Concepts

3 Identify benefits and added value for the operators

Target audience

The target audience for this course is anyone that wishes to get a basic introduction to the MSC Server Blade Cluster.

Prerequisites

There are no prerequisites to this web based learning course.


The length of the course is 50 minutes.

Learning situation

The web based learning course is aimed for selfstudy.

18

Time schedule

The time estimation is approximately.

Hour Topics in the course Estimated time

1 Components 15 min

Concepts 15 min

Benefits 15 min

Questions 5 min






SIP/SIP-I in MSS R6

LZU 108 7688 R2A

Description

For those who wish to know how VoIP interworking is handled in MSS R6this course provides an introduction to SIP / SIP-I signaling in MSS by presenting the protocol principles and different interworking traffic cases.

The SIP core protocol and the most important VoIP related extensions to SIP and SDP are presented as well as SIP-I and ISDN interworking basics.

Learning objectives


1 Describe the main nodes and interfaces for VoIP connections in MSS R6.01.1 Name the main logical nodes in the IMS System and describe their functionality1.2 Explore the possible interfacing networks for SIP/SIP-I

2 Explain the functions and capabilities of SIP protocol and its use in MSS networks2.1 Describe the basic functions and capabilities of SIP2.2 Name the major IETF protocols related to SIP, IMS and VoIP2.3 List the SIP methods used in MSS and state their function2.4 Explain the routing and addressing principles of SIP signaling2.5 Understand the SIP protocol header fields that are most important to basic SIP and

MSS 2.6 Appreciate the offer / answer model for SDP usage in SIP2.7 Describe how SIP-I relates to BICC/ISUP and SIP2.8 Relate the steps in a basic session establishment between MSS and

an external VoIP network

3 Make clear the protocol interworking at different traffic cases within MSS3.1 Explore the basic interworking between ISUP and SIP/SIP-I3.2 Explore the basic interworking between BICC and SIP/SIP-I.

Target audience

The target audience for this course are: System Technician, System Engineer, Network Design Engineer and Network Deployment Engineer.

20

Prerequisites

Students should have working experience of MSC-S and M-MGw up to at least MSS R6.0 level.

Attendance on the MSC-S R14.1 Configuration Delta LZU 108 8007 and M-MGw R6.1 Delta LZU 108 8011 courses is recommended.

Furthermore, the students should have a basic understanding of datacom in general and, more specifically, a good knowledge of IP networking and the TCP/IP protocol family.


The length of the course is 1 day and the maximum number of participants is 16.

Learning situation


Time schedule



1 Introduction. Nodes & interfaces 0.5 hours

The SIP protocol 5 hours

Protocol interworking 0.5 hours






MSS Performance Management

LZU 108 7691 R2A

Description

Do you have the competence to initiate, collect and analyze the statistics collected from your MSS network? Performance data collected from the network is used to analyze how well the network is performing and is a basis to plan for network and configuration changes.

The “MSS R6 Performance Management” training demonstrates how statistics is initiated, collected and processed in/from the MSC-S (APG43 / Blade Cluster based) and the M-MGw network elements. After the training, the participants will also understand the role of the OSS-RC in the performance management process, and the use of the ENIQ and Business Objects (BOs) for collecting and post-processing of the statistics data. Examples of how performance data could be used to identify potential problem areas in the current network configuration/dimensioning will also be covered.

Learning objectives


1 Explain the statistics handling procedure in the MSS 1.1 Identify the general concepts associated with traffic theory in the context of MSS,

such as traffic demand, offered traffic, carried traffic, call congestion and time congestion

1.2 Distinguish between the types of performance data collected in the MSC-S and the M-MGw

1.3 Explain how the MSC-S (APG43 / Blade Cluster based) collects and stores the statistics

1.4 Explain how M-MGw collects and store the statistics 1.5 Explain how the OSS-RC initiates, collects and post-processes the statistics1.6 Explain the role of ENIQ in collecting and post processing of the statistics collected

from the MSC-S and the M-MGw nodes

2 Understand the statistics handling process in the MSC-S (STS on APG43)2.1 List and explain the different types of counters in STS on APG43 and the Blade

Cluster2.2 Recognize the STS collection, accumulation and translation process2.3 Print and set the Basic Recording Period (BRP)2.4 Manage Object Types, Measurement Reports and Measurement Programs2.5 Understand the Key performance Indicators (KPIs) used in the MSC-S for different

areas, including Paging, Location Update

3 Understand the statistics handling procedure in the M-MGw3.1 Identify M-MGw counter types and counter groups3.2 Explain and find the counters using Managed Object Model in the system

documentation

22

3.3 View the counter and counter values using Node Manager3.4 Understand the grouping and formulae for Key Performance Indicators (KPI) and

Performance Indicators (PI) based on the counter values

4 Use the Performance Management applications in the OSS-RC to work with the M-MGw and MSC-S nodes

4.1 Initiate the statistics and collect them in the OSS-RC4.2 Differentiate between the Statistical Data Mart (SDM) in OSS-RC and the Ericsson

Network IQ (ENIQ) based solution for performance management4.3 Use the Business Object (BO) Report Generator to create traffic measurement report

examples4.4 Analyze performance data (provided to the participants) from the MSS network to

identify problems in the network

Target audience

The target audience for this course is: Network Design Engineers, Network Deployment Engineers, System Technicians and System Engineers.

This audience is expected to work with monitoring of the performance of the MSS network

Prerequisites

The participants should be familiar with:

M-MGw R6.1 Operation & Configuration

MSC-S R14.1 Blade Cluster Configuration

Basic OSS-RC knowledge


The length of the course is 3 days and the maximum number of participants is 8

Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using equipment and tools.






Time schedule



1 Chapter 1: Statistics handling procedure in MSS 3 hours

1,2 Chapter 2: Statistics Handling in the MSC-S and exercise 6 hours

2 Chapter 3: Statistics Handling in the M-MGw and exercise 3 hours

3 Chapter 4: Performance Management Applications in OSS and exercises

6 hours






Blade Cluster Data Transcript Workshop

LZU 108 7695 R2A

Description

Do you want to extent your understanding of Blade Cluster configuration skills?

This course provides a great opportunity to explore more specific details in exchange data to connect MGW, BSC, RNC nodes and other PSTN/PLMN/IMS interconnections to an MSC-S BC.

Learning objectives


1 Introduction of data transcript process 1.1 Briefly describe the data transcript process.1.2 Understand how the data transcript files are organized.

2 Verify and setup the signaling in the MSC-S BC2.1 Check the defined IP stack on CP.2.2 Define the signaling transport (SIGTRAN) in an MSC-S BC.2.3 Set SUA signaling between MSC Blades and SPX.2.4 Compare associated and quasi-associated signaling modes configuration in MSC-S

BC.

3 Detail the MGW, BSC and RNC nodes connection in the MSC-S R14.1 Blade Cluster3.1 Provide the data transcript necessary to add MGW in the MSC-S BC.3.2 Explore the MGW selection process in the MSC-S BC.3.3 Add BSC nodes in the MSC-S BC.3.4 Define the A-interface over IP.3.5 Configure RNC node in the MSC-S BC.3.6 Write the exchange data for Iu over IP connection.

4 Interworking route trunks setup in MSC-S BC4.1 Create new remote ISUP route to the PSTN network in the MSC-S BC.4.2 Write the exchange data for traffic connections to a MSC-S non-BC node.4.3 Define SIP/SIP-I route to an IMS network.

5 Configure Mobile Originating and Terminating calls in the MSC-S BC5.1 Perform b-number analysis table updates in the MSC-S BC.5.2 Enter exchange data for the signaling connections towards HLR.5.3 Define the roaming and handover number series (MSRNS) in the MSC-S BC.

6 Configure the MSC-S Blade Cluster IO system (optional)6.1 Check the current cp groups defined in the APG43.6.2 List the main difference between Expert and Normal modes6.3 Set up a new channel in WinFiol using multiple CP system options.

25

Target audience

The target audience for this course is: Service Planning Engineers, Network Deployment Engineers, Service Deployment Engineers, System Engineers, Service Engineers.

This audience is responsible for the data transcript of MSC-S BC nodes.

Prerequisites

The participants should successfully complete the following courses or equivalent knowlegde:

MSC-S R13.2 to R14.1 Blade Cluster Operation & Configuration Delta, LZU 108 8010 R1A

or

MSC-S R14.0 to R14.1 Blade Cluster Configuration Delta, LZU 108 8000 R1A



Learning situation

This is a task-oriented learning course based on tasks in the work process given in a technical environment using equipment and tools, which can also be accessed remotely.

Time schedule



1 Course Introduction & Pre-test 0.5 hours

Verify and setup the signaling in the MSC-S BC 4.0 hours

1 / 2 Detail MGW, BSC and RNC nodes in the MSC-S BC 2.0 hours

Interworking Route Trunks in MSC-S BC 3.0 hours

Mobile Originating and Terminating calls in the MSC-S BC 2.0 hours

Conclusion & Post-test 0.5 hours






A-Interface over IP in MSS

LZU 108 7999 R1A

Description

Do you want to know how to configure the A-Interface over IP (AoIP) for the nodes MSC-S, BSC and M-MGW? How this new architecture can provide new feature such as: Transcoder Free Operation with AoIP and 2G&3G M-MGW pool enabled by AoIP.

This course is a must for those who want to know how to configure the A-Interface for the nodes MSC-S, BSC and M-MGW using a Data Transcript example.

Learning objectives


1 Describe the A-interface1.1 Introduce A-Interface over IP (AoIP) 1.2 List the Operator Benefits

2 Describe the protocols used for A-Interface user plane traffic2.1 Examine the protocols used for A-Interface control plane traffic (BSSAP)

3 Establish the steps to configure A-Interface over IP (AoIP)3.1 Explain how the A-Interface over IP interface is configured on the MSC-S3.2 Explain how the A-Interface over IP interface is configured on the BSC3.3 Explain how the A-Interface over IP interface is configured on the M-MGw

4 Explain Transcoder Free Operation with A-Interface over IP (AoIP).

5 Describe MSC Pool with AoIP5.1

Target audience

The target audience for this course is: Service Planning Engineers, Service Design Engineers, Network Design Engineers, Network Deployment Engineers, Service Deployment Engineers, System Technicians, Service Technicians, System Engineers, Service Engineers, Field Technicians, System Administrators, Application Developers, Business Developers, Customer Care Administrators.

An example of both the mandatory Target Audience and a “free text” are; The target audience for this course is: System Engineers, Service Engineers.This audience is responsible for configuration of the MMC.

Prerequisites

Successful completion of the following courses:• GSM System Survey LZU108 852

27

• SIGTRAN Workshop LZU 108 6809

The participants should have competence on IP Networking and working experience of MSC-S R 13.2


The length of the course is 1 day and the maximum number of participants is 16

Learning situation

This course is based on theoretical instructor-led lessons given in a classroom environment






Time schedule



1 Describe the A-interface

Introduce A-Interface over IP (AoIP)

List the Operator Benefits

Describe the protocols used for A-Interface user plane traffic

Examine the protocols used for A-Interface control plane traffic (BSSAP)

Establish the steps to configure A-Interface over IP (AoIP)

Explain how the A-Interface over IP interface is configured on the MSC-S

Explain how the A-Interface over IP interface is configured on the BSC

Explain how the A-Interface over IP interface is configured on the M-MGw

Explain Transcoder Free Operation with A-Interface over IP (AoIP).

Describe MSC Pool with AoIP

0.5 hours

0.3 hours

0.2 hours

0.5 hours

0.5 hours

0.5 hours

1.0 hours

1.0 hours

0.5 hours

0.5 hours

0.5 hours











MSC-S R14.0 to R14.1 Blade Cluster Configuration Delta

LZU 108 8000 R1A

Description

Do you need know how configuration in MSC-S Blade Cluster (BC) R14.0 differs from R14.1? What benefits will these changes bring? How will these changes affect the operation of the network and which new options are introduced?

This course provides just that; by explaining the new concepts to this release. This knowledge will provide a solid foundation for taking benefit of the new options in conjunction with significant MSS features such as A-interface over IP, Call Completion to Busy Subscriber (CCBS), HPLMN Controlled ORLCF and others.

Learning objectives


1 List the different hardware and configuration in MSC-S R14.1 according to customer product information

1.1 Identify the new IS hardware base for MSC-S R14.1 BC.1.2 Describe the new cluster objects in the Cluster Circuit Sharing (CCS) feature.1.3 Understand how configuration differs from the previous MSC-S R14.0 BC.1.4 Express the performance management impact due to the new MSC-S R14.1 BC.

2 Discuss the new and enhanced features in MSC-S R14.1 BC 2.1 List and explain the changes to functionality, the new concepts and the related

benefits of the new features: A-Interface user plane over IP, Call Completion to Busy Subscriber (CCBS), HPLMN Controlled ORLCF, Support of SIP-I Screening and others.

2.2 View how features are improved in MSC-S R14.1 BC such as MSC in Pool, SIGTRAN, Media Gateway Selection and others.

3 Recognize the upgrade main steps due to MSC-S R14.1 BC introduction 3.1 Explore how external nodes see MSC-S R14.1 BC in terms of signaling.3.2 State the payload load routes migration to MSC blades on high level3.3 Describe common signaling flows on a high level (internal flows in MSC-S BC).

Target audience

The target audience for this course is: System Technician, System Engineer, Network Deployment Engineer.

31

Prerequisites

Those attending need to have competence in MSC-S Blade Cluster R14.0 and should have either successfully completed the following course or otherwise acquired the relevant pre-knowledge:

MSC-S R14.0 Blade Cluster Overview LZU 108 7681 R1A

MSC-S R14.0 Blade Cluster Delta LZU 108 7683 R1A



Learning situation


Time schedule



1 Course Introduction & Pre-Test 0.5 hour

Configuration Delta R14.1 from R14.0 1.5 hours

New and Enhanced Features in MSC-S BC R14.1 2.5 hours

Upgrade from MSC-S R14.0 1.0 hour

Conclusion & Final Test 0.5 hour






MSS R6.1 Network Planning and Hardware Dimensioning

LZU 108 8001 R1A

Description

Do you need to understand the process and calculations involved in Network Planning and Hardware Dimensioning for MSS? This course covers those steps in the Circuit Switched Core Network for MSS R6.1 (MSC-S R14.1 and MGw R6) and HLR/AUC. The course focus is on high level design of the circuit switched core network, which includes Traffic, Interconnection and Signaling Network Planning.

Learning objectives


1 Acknowledge the solutions for Product Packages available.1.1 Describe the network architecture and its main nodes1.2 Recognize the Product Packages for MSC Server1.3 Recognize the Product Packages for M-MGw.1.4 Recognize the Product Packages for the Signaling/Database nodes.

2 Explain and apply the methodology used for planning a Core Network.2.1 Explain the process of traffic planning2.2 Explain briefly traffic modeling2.3 Based on hypothetical examples, describe subscriber distribution in the network in

terms of CS traffic for both GSM and WCDMA systems2.4 Describe the traffic model used in given hypothetical examples and define CS traffic

cases in connection with the traffic model2.5 Based on defined traffic cases, calculate CS traffic distribution and dispersion

3 Describe the processor capacity and list the factors that impact processor capacity.3.1 List different types of processor load3.2 List different ways of expressing processor capacity3.3 List factors that impact processor capacity3.4 Identify central processors in AXE and their capacity relations3.5 Debate the considerations for Blade Cluster dimensioning

4 Explain on an overview level, the M-MGw and the Connectivity Packet Platform 4.1 Distinguish between call control and bearer control4.2 Describe the logical network design4.3 Explain the dimensioning process of the nodes in the CS domain4.4 Describe the preliminary determination of product packages

5 On an overview level, explain the process of planning the transport plane and be able to apply it to a simple network.

5.1 Describe TDM user plane design considerations.5.2 Describe ATM user plane design considerations.5.3 Describe IP user plane design considerations.

33

6 Explain the signaling network design process.6.1 List some of the signaling interfaces for CS domain6.2 Describe SS7 protocol stacks6.3 Explain signaling volumes calculation6.4 Explain signaling links calculation

Target audience

The target audiences for this course are: Network Design Engineer and Network Deployment Engineer.

Prerequisites

Successful completion of the following flows:

Mobile Softswitch Solution Fundamentals

GSM Fundamentals area

WCDMA Fundamentals area

MSC-S R14.1 Blade Cluster Fundamentals



Learning situation







Time schedule



1 Course Introduction and Pre-test 1 hour

Overview of Product Packages 1 hour

Traffic Planning 2 hours

Exercises Chapter 2 2 hours

2 Processor Dimensioning 2 hours

Exercise Chapter 3 2 hours

Circuit Switched Network 2 hours

3 Exercises Chapter 4 2 hours

CS User Plane Design 4 hours

4 Exercises Chapter 5 3 hours

Signaling Network Design 2 hours

Exercises Chapter 6 1 hour

5 (optional) Blade Cluster Dimensioning considerations 4 hours

BC Dimensioning exercises 1 hour

Post-test 1 hour






MSS Troubleshooting

LZU 108 8002 R1A

Description

Is there a need to improve the overall network performance? Are you able to discover the problems and correct them in an MSS network? Do you need to know how to troubleshoot?

The MSS Troubleshooting course is designed for MSS professionals that need to enhance there troubleshooting skills. The course provides a generic troubleshooting theory, applicable in both Datacom and Telecom networks. The students will practice the theory through exercises, solving problems in MSS networks, including MSC Classic, MSC Server, MSC Server Blade Cluster and Mobile Media Gateway (MGw). This course adds value to the operators, since they will easier find the problems and correct them in the MSS networks.

Learning objectives


1 Identify ways how to solve the problem1.1 Identify and solve the problem – Introduction1.2 List different general troubleshooting techniques1.3 Describe some white-box information sources

2 Investigate Theory & Strategy2.1 Apply the 4 troubleshooting techniques2.2 Describe how to reproduce a problem2.3 Explain the troubleshooting strategy

3 Explore nodes and interfaces in MSS3.1 List nodes in MSS3.2 Describe interfaces in MSS3.3 Identify used protocols in MSS

4 Review MSS related documentation4.1 Explore Alex for all nodes4.2 Access Protocol Specifications4.3 Practice finding useful information

5 Illustrate how to use the MGw5.1 List MGw functionality and features5.2 Show how MGw realizes “All over IP”5.3 Utilize the MGw statistical counters

6 Demonstrate how to use the Protocol Analyzers6.1 Illustrate how protocol analyzers can be used6.2 Identify protocols that can be utilized6.3 Explore how to use WireShark

7 Describe how to take benefits of protocols

36

7.1 Explain how a normal call is handled7.2 Recognize how to use the protocol analyzer7.3 Analyze how to solve a problem using protocols

8 Troubleshoot essential call traffic scenarios8.1 Verify telecom protocols8.2 Utilize protocol analyzers and Alex8.3 Solve essential problems

9 Show Logs and Events in MSS9.1 Identify existing Logs & Events9.2 Describe their purposes 9.3 Explain how to utilize the Logs and Events

10 Troubleshoot advanced call traffic scenarios10.1 Verify Logs and Events10.2 Utilize logs and events together with Alex10.3 Solve advanced problems

Target audience

The target audience for this course is: System Engineers, Service Engineers and System Administrators.

Prerequisites


Signaling in the Core Network - MSS LZU 108 7519

WCDMA Maintenance MSC Extended LZU 108 5031/1 orGSM Maintenance MSC/BSC Extended LZU 108 5031/2

M-MGw Configuration with AMOS LZU 108 8013

The participants should have recognized experience of working with the MSS nodes.



Learning situation

The course is a mix of instructor-led training and task-oriented learning given in a classroom environment. The exercises are based on remote equipment (MGw) and simulated networks in real-time (SEA). Alex, Winfiol and Citrix will be installed on the local classroom computers, providing a pedagogic and 100% realistic troubleshooting environment.






Time schedule



1 Identify ways how to solve the problem 1 hour

Investigate Theory & Strategy 1 hour

Explore nodes and interfaces in MSS 1 hour

Review MSS related documentation – Exercise 1 2 hours

Illustrate how to use the MGw 1 hour

2 Practice how to use the MGw – Exercise 2 5 hours

Demonstrate how to use the Protocol Analyzers 1 hour

3 Practice how to use the Protocol Analyzers – Exercise 3 5 hours

Describe how to take benefits of protocols 1 hour

4 Troubleshoot essential call traffic scenarios – Exercise 4 5 hours

Show Logs and Events in MSS 1 hour

5 Troubleshoot advanced call traffic scenarios – Exercise 5 5 hours

Relate experiences from course to reality 1 hour






MSC-S R14.1 Blade Cluster Overview

LZU 108 8003 R1A

Description

What is an MSS Blade Cluster? Why was it introduced? What benefits does it bring to the operator?

The MSS Blade Cluster Overview answers these questions. The course places the MSS Blade Cluster (MSS BC) in context explaining how it relates to basic telecom and datacom concepts. The MSS BC hardware, software, and functionality are explored as well as the differences between MSS BC and classic MSC Server. The system capacity is evaluated and the new procedures and commands are introduced.

Learning objectives


1 Identify Benefits and Drivers for MSS BC – Why MSS BC?1.1 Give an example of an MSS site before and after migration to MSS BC1.2 Describe the reasons for introducing MSS BC1.3 Recognize and list the added value introduced in MSS BC

2 Explain the MSS BC Concepts2.1 Clarify how IS and APZ are merged2.2 Introduce new concepts, like Single-Sided-CP and Buddy-MSC2.3 Demonstrate how traffic is handled within the MSC-S BC

3 Present the MSS BC Characteristics 3.1 Explore the recovery behavior3.2 Acknowledge the performance and footprint of the MSC-S BC3.3 Describe the improved node availability and robustness mechanisms

4 Identify the Hardware Components in MSC-S BC4.1 Define the three different MSS BC configurations4.2 Identify the hardware components, from cabinet to blade4.3 Explain briefly the purpose of the hardware components

5 Describe Protocols and Signaling in MSS BC0.1 Give an overview of protocols used in MSC-S BC0.2 Apply the OSI model on MSC-S BC and identify key functionality on different layers0.3 Illustrate how traffic is routed inside MSC-S BC

6 List and Describe MSS BC Software Components 6.1 List the main software components in MSS BC, APZ 212 60 and APZ 214 036.2 Explain briefly the purpose of each software component6.3 Illustrate how the MSC-S BC functionality is implemented by the software

7 Give an introduction to Operation and Configuration of the MSS BC 7.1 Clarify the role of Site Infrastructure Support (SIS) and APG in MSS BC

39

7.2 Describe User Interfaces and Operator Support functions7.3 List important new procedures and commands

Target audience

The target audience for this course are: Network Deployment Engineers, Service Deployment Engineers, System Technicians, Service Technicians, System Engineers, Service Engineers

Prerequisites

The participants should be familiar with basic concepts of the Mobile Softswitch Solution or attended the following course:

MSS R6.1 Survey LZU 108 8004 R1A

The participants should also have basic knowledge about the Integrated Site (IS) Concept. The following course is highly recommended:

IS 3.1 Overview, LZU108 7566



Learning situation

This course is based on theoretical instructor-led lessons given in classroom.

Time schedule


Day Topics in the course Estimated time1 Benefits and Drivers for MSS BC – Why MSS BC? 1 hour

BC Concepts 1 hourBC Characteristics 0,5 hourHardware Components 1 hourProtocols and Signaling 0,5 hourSoftware Components 1 hourOperation and Configuration 1 hour






MSS R6.1 Survey

LZU 108 8004 R1A

Description

Do you need to know the changes in the network while introducing the Mobile Softswitch Solution (MSS) and are you familiar with working in a non-layered network? The meaning of Mobile Softwswitch Solution (MSS) and its impact on your competence to work in the Network is illustrated. The Signalling Protocols involved in the MSS are introduced and MSC-Server and Mobile Media Gateway (M-MGw) are explained from an operational and configuration perspective.

Learning objectives


1 Introduce a network based on the Mobile Softswitch Solution according to Ericsson Customer Product Information

1.1 Explain why Mobile Softswitch was introduced and the associated advantages 1.2 Illustrate the functionality of the Network Elements in MSS Networks.1.3 List the different interfaces in MSS Networks.1.4 Illustrate the architecture and interfaces for an Ericsson MSS Network.1.5 Illustrate the new A-interface over IP1.6 Describe briefly SIP/SIP-I supported in MSS R6.1

2 Explain the protocols involved in the Ericsson MSS. 2.1 Explain the Bearer Independent Call Control (BICC) protocol on an overview level.2.2 Explain the Gateway Control Protocol (GCP) on an overview level.2.3 Explain the QAAL2 (Q2630) protocol on an overview level.2.4 Explain the IP Bearer Control Protocol (IPBCP) on an overview level.2.5 Explain the NbUP protocol on overview level at the Generic Media Gateway Platform

(GMP).

3 Describe Hardware platform for the MSC-Server 3.1 Describe the Interfaces from the MSC Server to other nodes in the MSS Networks3.2 Understand the Data Transcript required in the MSC Server for the MSS3.3 List the functionality of the MSC Server3.4 Describe Blade Cluster in MSS R6.1

4 Explain the CPP functions and GMP concept4.1 Illustrate the GMP Hardware Architecture 4.2 List the M-MGW Product packages.4.3 Understand Element Management in MGW 6.14.4 Illustrate the GMP cabinets, subrack and boards for M-MGw4.5 List enhancements in MGW 6.14.6 Describe IP transport enhancement4.7 Illustrate VoIP Gateway4.8 Describe MSC Pool Proxy.

41

Target audience

The target audience for this course is: Network Design Engineer, System Technician, System Engineer and Network Deployment Engineer.

Prerequisites

Competence in Core Network Operation and Configuration for MSC-S R12 in a non-layered Core Network, and M-MGW



Learning situation


Time schedule



1 Course Introduction and Initial test 0.5 hour

Introduction to MSS Networks 1,5 hours

Introduction to Signaling in MSS 1.0 hour

MSS signaling protocols overview 3 hours

2 MSC Server 2.75 hours

Mobile Media Gateway 2.75 hours

Course Conclusion and Summary 0.5 hour






Blade Cluster Platform Operation and Maintenance

LZU 108 8005 R1A

Description

Do you know that the AXE Blade Cluster is a system in which are involved more than one node configured differently in function and hardware as a MSC or a HLR, and a Signalling Proxy (SPX) applications? Would you like to be able to able to understand, operate and maintain a CP Cluster System?

This course contains a balanced description of the classical AXE Platform Applications delivered by Ericsson and the AXE Blade Cluster system.

Through practical exercises the participants will gain experience in handling a Blade Cluster System by sending commands and analysing alarms and printouts.

Learning objectives


1 Provide an overview of the AXE Blade Cluster system1.1 Explain what a MSC-S/HLR-S Blade Cluster system is.1.2 Explain the APZ evolution.1.3 Identify the basic concepts of the HLR-S/MSC-S Blade Cluster main components.1.4 Describe the IS infrastructure used in an AXE Blade Cluster system.1.5 Identify Integrated Site (IS) applied to APZ 214 03.

2 Describe the AXE Blade Cluster Hardware view2.1 Explain the building blocks of the SPX: APZ 212 60 and AUP.2.2 Describe the APG43/2 characteristics for a HLR-S/MSC-S Blade Cluster2.3 Describe the APZ 214 03 HW integrated into the IS environment.

3 I/O in BC Systems3.1 Use command lines and GUI (ISM, Winfiol) to access the Cluster CPs in both AXE

and IS environments.3.2 Execute commands and analyze printouts for a Cluster CP in a protected or an

unprotected mode.

4 Demonstrate use of the Cluster Handler (CH) in a CP Cluster system4.1 Describe the CH software components.4.2 Describe the Cluster and Quorum terminologies and concepts.4.3 Describe CP Cluster states and sub-states.4.4 Execute commands and understand printouts used to support the CP Cluster

operation.

43

5 Operate APZ 214 03 in a CP Cluster system5.1 Demonstrate use of the software management activities to perform system backup,

cloning and software upgrade in a Cluster CP.5.2 Demonstrate use of the initial loading and reloading in a Cluster CP.

6 Discriminate the Fault Handling recovery procedures for APZ 214 036.1 List the Hardware Fault recovery processes for CP Cluster.6.2 Repair faults in APZ 214 03 Hardware.6.3 List the Software Fault recovery handling for CP Cluster.6.4 Demonstrate use of Cluster and Blade recovery functions and alarms.6.5 Understand the APZ 214 03 logs located in APG43/2.

7 Demonstrate use of the XPU (eXtra Processing Unit) 7.1 Describe the New XPU execution domain 7.2 Use commands to Operate XPU.7.3 Repair faults in XPU.

Target audience

The target audience for this course is:

System Technicians, System Engineers and Network Deployment Engineers.

Prerequisites

Successful completion of the following courses: APZ 212 60 Operation & Maintenance LZU 108 7561Integrated Site 3.1 Overview LZU 108 7566Integrated Site 3.1 Operation & Configuration LZU 108 7567



Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in technical environment using equipment and tools.






Time schedule


Day Topics in the course Estimated time1 Introduction

HW viewI/O for BC Systems ExercisesCP Cluster System

1 hour1 hour2 hours1 hour1 hour

2 CP Cluster System (cont.)ExercisesOperation handling for Blade ClusterExercises

1 hour 1,5 hour2 hour

1,5 hours

3 ExercisesFault handling for Blade ClusterExercises

1 hour 3 hours2 hours

4 XPU HandlingExercisesFinal evaluation

3 hours2 hours1 hour






MSC/MSC-S R14.1 Data Transcript

LZU 108 8006 R1A

Description

Do you have enough knowledge about GSM/WCDMA Data Transcript? Do you want to practice more about it? This course is a must for anyone needing to develop knowledge and understanding of exchange data to a point where you will be able to interpret exchange requirements and write the data transcript for basic traffic cases in the GSM/WCDMA networks involving the MSC/MSC-S connections with BSC/RNC, MGw, HLR and other nodes. By engaging in theoretical sessions and practical exercices, you will have the opportunity to explore data transcript production, inputs, flow and ideas.

This course supports the GSM/WCDMA technologies MSC Classical, MSC-S Non-BC and MSC-S BC up to R14.1.

Learning objectives


1 Recognize the network architecture and components of the GSM/WCDMA network according to system documentation.

1.1 Name the network architecture of Ericsson's GSM/WCDMA network.1.2 List the main nodes and their functions in the GSM/WCDMA network.1.3 Explain and list the PLMN identities and briefly describe the function of each.

2 Discuss basic Traffic Cases as outlined in the MSS R5.1 system documentation.2.1 Identify the signaling protocols used between the different nodes.2.2 Revise location-updating procedures.2.3 Clarify procedures for calls to and from an MS/UE.2.4 Describe the different types of handover.2.5 State basic SMS traffic for mobile originating and terminating calls.

3 Understand the Data Transcript process according to system documentation.3.1 Explain the inputs and outputs of the Data Transcript process.3.2 Use the Customer Product Information (ALEX Document Browsers) in order to find

appropriate commands, parameters and parameter values.3.3 Underline the 1317 list (Product Code List), in conjunction with the ALEX browsers, in

order to find the necessary information to create the data transcript.3.4 Identify the process of converting a reference dump into a working dump.

4 Create the data transcript required to support specific network configuration based on system descriptions of the different signaling systems.

4.1 Write the MML for traffic connections to other MSCs and other networks by interpreting the Exchange Requirements.

4.2 Create the MML for the MTP signaling connections towards HLR and other MSCs and towards other networks by interpreting the Exchange Requirements.

46

4.3 Explain how High Speed Signaling Links (HSL) can be implemented in a network and the advantage of doing so.

4.4 Write the MML to define Software Routes and Common Exchange Equipment.

5 Define how signaling is transmitted over IP (SIGTRAN) and the associated MML as outlined in the system documentation.

5.1 Describe the concepts and protocols of SIGTRAN and the advantages of it.5.2 Discuss the protocol stack of SIGTRAN.5.3 Identify the entities in the signaling network regarding IP transmission.5.4 Examine the new implementation of GCP over SCTP.5.5 Write the MML for signaling communication over SIGTRAN between different nodes.

6 Identify the Mobile Softswitch Solution R5.1 and its features accordingly to system documentation.

6.1 Provide MSC-Server and M-MGW functions in the MSS architecture.6.2 List the new sets of data necessary to define the Call Set up in the MSS architecture

for MSC-S and Media Gateway6.3 List and briefly explain the service devices: Speech Coder function (SC), Echo

Canceller function (EC), Tone Sender/Receiver function (TSR), Interactive Messaging function (IM), Multi Party Call function (MPC), Circuit Switched Data function (CSD).

6.4 Explain the concepts of remote TDM devices, MGW selection, BICC, GCP and be able to set configuration data in the MSC-Server.

6.5 Write the MML for M-MGW definition in MSC-S.6.6 Discuss the concept of TFO/TrFO and the inter-working.6.7 Illustrate the MML required for basic traffic case using TFO, TrFO and Codec at the

Edge.6.8 Recognize the advantage of MSC in Pool feature.6.9 Write the MML required in the MSC/MSC-S and BSC to implement the MSC in Pool.6.10 Understand SIP & SIP-I and how these protocols are used in MSS 5.1 to access IMS

servers.6.11 Illustrate traffic cases for SIP & SIP-I and the MML required in the MSC-S to support

these protocols.

7 Demonstrate the BSC/RNC connection to MSC in Non Layered Architecture and Layered Architecture.

7.1 Understand the BSC/RNC signaling protocol to the Core Network.7.2 Write the BSC/RNC signaling data toward the Core Network.7.3 Create the BSC/RNC traffic route data toward the Core Network.

8 Describe how the MSC/MSC-S and HLR communication using SCCP is performed at Location update.

8.1 Write the MML for the SCCP communication between MSC/MSC-S to HLR, and HLR to MSC/MSC-S, by interpreting the exchange requirements.

8.2 Write the MML for defining the roaming agreements by interpreting the exchange requirements.

9 Outline how Telecommunication Service Analysis is performed in the MSC/MSC-S according to the system specifications.






9.1 Explain the function of the BASC in translating a GSM/WCDMA BC to/from an ISDN BC.

9.2 Define the TSA for a teleservice and for a bearer service.9.3 Identify the TMR analysis input and output parameters.9.4 Name the purpose of the Compatibility Check.

10 Highlight the analysis required for routing a mobile call as per the system documentation.

10.1 List the various types of analysis used for routing mobile originating calls and explain the major parameters.

10.2 Write MML supporting a call from an MS by interpreting exchange requirements

11 Explain how GSM/WCDMA Network elements work together on a call from PSTN/ISDN subscriber to a GSM/WCDMA mobile subscriber.

11.1 List the various types of analysis used for routing mobile originating calls and explain the major parameters.

11.2 Write MML supporting a call from an MS/UE by interpreting the exchange requirements.

12 Describe how Call Data Records are generated and used as described in the system description.

12.1 Understand how a Call Data Record is generated for the different phases of a call12.2 Correctly interpret the information from the exchange requirements and write the MML

to support charging analysis (traffic dependent charging and charging analysis).

13 Create the exchange data for announcements in the MSS architecture.13.1 Understand the phrase of announcements.13.2 Configure access to announcement and the route data.13.3 Write DT example of announcements.

Target audience

The target audience for this course is: Service Planning Engineers, Network Deployment Engineers, Service Deployment Engineers, System Engineers, Service Engineers.

Prerequisites

The participants should be successful completion of the following courses (or equivalent knowledge or experience):

AXE 810 Data Transcript LZU 108 6134 R3A








Learning situation


Time schedule



1 Course Introduction & Pre-Test 0.5 hour

Introduction 1.0 hour

Traffic Cases 2.0 hours

Introduction to Data Transcript 1.0 hour

2 Classic Routes and Signaling Circuits 1.0 hour

SS7 over IP Transport Signaling 3.0 hours

2 / 3 MSC-S Server and Media Gateway 3.0 hours

BSC or RNC Connection 3.0 hours

3 / 4 Location Updating 3.0 hours

Telecommunication Service Analysis 1.0 hour

Mobile Originating Call 3.0 hours

4 / 5 Mobile Terminating Call 3.0 hours

Charging Analysis 1.5 hours

Announcements in MSS architecture 1.5 hour

Conclusion & Post-Test 1.0 hour






MSC–S R14.1 Configuration Delta

LZU 108 8007 R1A

Description

The introduction of the Mobile Softswitch Solution (MSS) into existing Networks coincides with the introduction of the MSC Server concept. New configuration tasks have become a necessity for system engineers working with the MSC Server node compared to the classic MSC. This course expands the competence of personnel working with MSC/VLR Configuration today towards executing the additional, new configuration tasks on the MSC Server.

Learning objectives


1 Interpret a call setup in the Mobile Softswitch Solution.1.1 Explain the Bearer Independent Call Control (BICC) protocol on an overview level.1.2 Define the Gateway Control Protocol (GCP) on an overview level1.3 Explain the Q.AAL2 (Q.2630) protocol on an overview level1.4 Express the IP Bearer Control Protocol (IPBCP) on an overview level1.5 Acknowledge call setup signaling for IP based Core Networks1.6 Identify Bearer Setup Direction1.7 Interpret the concepts of bandwidth savings in Core Network through transport of

compressed speech

2 Configure M-MGWs, M-MGW Groups, M-MGW Selection and Bearer Setup Direction and explain the concepts.

2.1 Detect the relations between MSC Server and M-MGW2.2 Define the concept of a Virtual M-MGW2.3 Recognize and define M-MGW Groups2.4 List the Media Gateway Selection2.5 Perform connections to a M-MGW2.6 Perform connections to a MSC Server using BICC or ISUP

3 Define the HW used for IP (SLI board) connections in an AXE switch.3.1 List Signaling Link Interface (SIGTRAN) definition3.2 Recognize GARP for GCP definition3.3 Recognize GESB for SIP type signaling

4 Insert RNC and BSC data using online documentation and explain the concept of the remote A-Interface.

4.1 Perform the connection to an RNC 4.2 Define the remote A-Interface4.3 Perform the connection to a BSC

50

5 Define ISUP signaling and explain the concept of remote devices.5.1 Interpret the E-SNT Concept5.2 Define an ISUP connection

6 Describe the different handover concepts.6.1 List the different Handover scenarios

7 Implement Signaling Transport over IP.7.1 Configure SIGTRAN from MSC Server point of view7.2 Describe and configure a redundant SIGTRAN setup

8 Implement SIP signaling in MSC-S8.1 Configure SIP local host, remote element and routes.

9 Configure Out of Band Transcoder Control Parameters.9.1 Identify the different parameters and commands to set up TFO/TrFO (Tandem Free

Operation / Transcoder Free Operation Interworking)

10 Define Bearer Independent Call Control (BICC) Monitoring and Event Reporting.10.1 Monitor faults in MSS using BICC Monitoring10.2 Check faults in MSS using Event Reporting10.3 Diagnose faults in MSS using Protocol Disturbances

Target audience


System Technicians, System Engineers, Network Deployment Engineer.

Prerequisites

Successful completion of:

MSS R6.1 Survey LZU 108 8004

MSC configuration or equivalent knowledge








Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using equipment and tools, which can also be accessed remotely.

Time schedule


Day Topics in the course Estimated time1 Introduction 0.5 hours

Protocols and Call Setup in Mobile Softswitch Solution 1.0 hoursM-MGw Groups, Media Gateway Selection and Bearer Setup Direction

1.0 hours

Hardware 0.5 hoursRNC and BSC Connection 1.5 hoursExercises 1.5 hours

2 ISUP signaling 0.5 hoursHandover Concept 0.5 hoursSIGTRAN 1.0 hoursSIP signaling 0.5 hoursTransport of compressed speech in the backbone and OoBTC 0.5 hoursBICC Monitoring and Event Reporting 0.5 hoursExercises 2.0 hoursConclusion and test 0.5 hours






MSC/MSC-S R14.1 Configuration

LZU 108 8008 R1A

Description

Do you need to know how to configure the MSC-S Non-Blade and MSC-S Blade Cluster functionalities in the Mobile Softswitch Solution? Hands-on practice in configuring various Traffic Cases in an MSC exchange is provided. You will also deal with the operation of the MSC, MSC Server Non-Blade and Blade Cluster based on and the Visitor Location Register (VLR) functional applications for the Mobile Softswitch Solution.

Learning objectives


1 Explain the main parts of Ericsson’s Systems network including Mobile Softswitch Solution.

1.1 Cite examples of basic traffic cases in a network1.2 Outline Blade Cluster with briefly detail1.3 Explain the System identities1.4 Detail the MGT (Mobile Global Title) concept1.5 Identify the Core Network Protocols in MSS Architecture

2 Explain the MTP network and briefly detail the MTP functions.2.1 Use MML printout commands to obtain a view of the MTP configuration and use the

Active Library Explorer to interpret the results.2.2 Set up MTP definitions in exchange data as outlined in the Customer Product

Information CPI and training material.2.3 Explain the function of High Speed Signaling Links.2.4 Explain the SS7 signaling over IP concept in MSC-S Non-Blade and in Blade Cluster

3 Set up SCCP definitions in exchange data as outlined in the Customer Product Information CPI and training material.

3.1 Explain the sequence for a signaling message in the SCCP.3.2 Use MML printout commands to obtain a view of the SCCP configuration and use the

Customer Product Information to interpret the results.3.3 Set up the Global Title Translation data in an exchange using the Customer Product

Information

4 Identify and explain the connection between the MSC-S and the M-MGw and Configure Trunk Routes in the BC

4.1 Describe the System and Signaling identities and the Cluster concept4.2 Explain the GSM and WCDMA system identities4.3 Identify the Core Network Protocols in MSS Architecture4.4 Describe Primary / Buddy blade concept and VLR data replication on high level

53

4.5 Explain Subscriber distribution and Cluster reconfiguration function principles4.6 Look at the relation between MSC blades, TSC blades and SPXs4.7 Explain a call setup in MSS4.8 Setup Inter-blade trunk routes & Remote TDM routes (A i/f & POI)

5 Define and explain the connection between the MSC and the Mobile Media Gateway.5.1 Relate the advantage and changes in the network and nodes applied in the Mobile

Softswitch Solution (MSS).5.2 Explain a call setup in MSS.5.3 List and explain the used signaling protocols and protocol stacks utilized in MSS5.4 List the sets of data necessary to define the Call Set up in MSS for MSC Server and

Mobile Media Gateway, including data related to the Gateway Control protocol (GCP) concept.

5.5 Explain the concepts of MGW group, MGW selection, Load control between MSC Server and MGW and be able to set the configuration data in the MSC-Server

6 Explain the RNC and BSC connection in both Classical and MSS architecture6.1 Detail the HW (ALI board) used for ATM connections in an AXE switch.6.2 Activate signaling over the ALI board.6.3 Define circuit switched traffic over the ALI board.6.4 Explain the RNC definition using GCP over ATM and GCP over IP.6.5 Insert RNC data using online documentation.6.6 Handle BSC signaling data6.7 Explain the BSC definition using GCP over ATM and GCP over IP.6.8 Insert BSC data using online documentation.

7 Explain the different Location Updating procedures at node level.7.1 Explain how Location Updating is handled in the MSC/MSC-S7.2 Define the exchange data in the MSC that is necessary to allow Location Updating.7.3 List the differences between GSM authentication and WCDMA authentication.7.4 Configure the exchange data for Location Updating in MSC using online

documentation.

8 Explain how an MS/UE – to – ISDN call is handled in each of the functional applications: GMSC, HLR, and MSC-S.

8.1 Define exchange data for the GMSC, HLR, and MSC to allow a mobile originated call.8.2 Explain how a mobile originated emergency call is analyzed in the MSC-S.8.3 Define exchange data in the MSC/VLR for a mobile originated call.

9 Configure the exchange data for a Mobile Subscriber terminated call in the MSC using online documentation.

9.1 Demonstrate how a mobile terminated call is analyzed.

10 Explain the Handover procedures in the Core Network10.1 Differentiate the GSM handover and the WCDMA handover procedures.






11 Configure the exchange data for Telecommunication Services Analysis according to the system documentation.

11.1 Explain the function of the BASC in translating the GSM or WCDMA BC to/from the ISDN BC.

11.2 Define the Telecommunication Service Analysis for a TeleService (TS) and a Bearer Service (BS).

11.3 List the Transmission Medium Requirement Analysis input and output parameters

12 Explain data fax calls and SMS according to the system documentation.12.1 Identify the SMS traffic cases.12.2 Interpret different traffic cases for GSM/WCDMA data calls using DTI equipment.

Target audience


System Technicians

System Engineers

Network Deployment Engineer.

Prerequisites

Successful completion of the following training flow and courses:


MSC-S R14.1 Blade Cluster Overview LZU 108 8003

WCDMA AXE Operation LZU 108 5024/1

Or

GSM AXE Operation LZU 108 5024/2



Learning situation

Define the Learning Situation/s for which the product might be used, for example instructor-led training, task-oriented learning, web-based learning etc. Look into the document "Definition of Delivery Methods for Learning Products" in the LPD Guidelines.






Time schedule


Day Topics in the course Estimated time1 Introduction 1 hours

MTP 3 hoursExercises 2 hours

2 SCCP 2 hoursMSC-S Blade Cluster 2 hours

M-MGw and MSC Server 2 hours3 Exercises 1.0 h ours

MSC-RNC/BSC Connection 2.5 hoursLocation Update 1.5 hoursExercises 1 hours

4 Call from UE 1.5 hoursCall to UE 1.5 hoursExercises 3 hours

5 Handover 2 hoursTelecommunication Service Analysis 2 hoursSMS FAX and Data Calls 2 hours






MSC/MSC-S R14.1 Features Delta

LZU 108 8009 R1A

Description

Do you want to know the main changes in MSC Classical or MSC-Server Non-BC R14.1? What benefits will these changes bring? How will these changes affect the operation of the network and which new options are introduced?

This course will answer these questions by presenting the added/changed features and by explaining the concepts new to this release.

This learning product belongs to MSS R6.1 for MSC Classical and MSC-Server Non-Blade Cluster.

Learning objectives


1 Recognize MSS R6.1 network elements, interfaces and architecture.1.1 Understand the different MSC nodes in this release and their main characteristics1.2 Describe the MSC-Server Blade Cluster node1.3 List the new M-MGW GMP V4 base configuration

2 Describe the enhanced basic features in MSC/MSC-S R14.12.1 State the enhancements in DTMF signaling, Media Gateway selection, Basic Mobile

Switching Services and GCP protocol.

3 Name the new and enhanced optional features in MSC/MSC-S R14.13.1 Acknowledge the new functionalities available in R14.1 – A-interface over IP, Call

Completion to Busy Subscriber (CCBS), Support of SIP-I Screening and Support of Interworking with MMTel/IMS, HPLMN Controlled ORLCF, Call Origin Based Routing and Clear Channel Data.

3.2 List the changes and related benefits of the optional features – MSC in Pool, MGCF for Interworking with IMS, MGCF for Interworking with SIP-I based Networks, DNS Resolver, TrFO & Compressed speech in the Core Network, Signaling Transport over IP and Ericsson Enhanced IN Capability Set 1 for Mobile Networks

Target audience

The target audience for this course is: Network Design Engineers, Service Planning Engineers, Service Design Engineers, Network Deployment Engineers, System Technicians, System Engineers and Field Technicians.

57

Prerequisites

The participants should have knowledge and working experience of MSC/MSC-S R13.2.



Learning situation

The participants should have knowledge and working experience of MSC/MSC-S R13.2.

Time schedule



1 Course Introduction & Pre Test 0.5 hour

Enhanced basic features 1.0 hour

New optional features 2.0 hours

Enhanced optional features 2.0 hours

Course Conclusion & Post Test 0.5 hour






MSC-S R13.2 to R14.1 Blade Cluster Configuration Delta

LZU 108 8010 R1A

Description

Do you need competence in how configuration of an MSC-S Blade Cluster (BC) differs from standard MSC-S handling?

This course provides just that; it covers the background theory needed for understanding the new MSC-S BC exchange data. It includes practical exercises showing configuration of the MSC-S BC platform and the MSC-S / VLR functions & services impacted by BC introduction. The MSC-S BC hardware and the cluster concepts are introduced. The principles for configuration of the Signaling Network and the exchange data for Call Routing are thoroughly described.

Learning objectives


1 Describe BC Hardware Platform and APZ basics1.1 List hardware used in an MSC-S R14.1 BC.1.2 Name the building blocks that constitute an APZ in a MSC-S BC.

2 Understand the Cluster concept2.1 Describe Primary / Buddy blade concept and VLR data replication on high level.2.2 Explain Subscriber distribution and Cluster reconfiguration function principles.2.3 Describe the relation between MSC blades and SPXs.2.4 Discuss the Cluster Circuit Sharing (CCS) principles.

3 List the new features in MSC-S R14.1 BC3.1 Identify and describe shortly the new features introduced MSC-S R14.1 BC.3.2 Demonstrate how the main new features are configured in MSC-S R14.1 BC

4 Configure IP on CP 4.1 Identify internal VLANs used in MSC-S BC.4.2 Setup IP definitions for SIGTRAN.

5 Describe M3UA & SUA usage in the MSC-S BC5.1 Exemplify Signaling Scenarios.5.2 Define signaling connection between MSC Blades and SPX.5.3 Locate how SS7 Signaling Point codes in MSC-S BC.

59

6 Configure Trunk Routes in the BC6.1 Setup Inter-blade trunk routes & Remote TDM routes (A-interface & POI).6.2 Describe the principles for A and Iu over IP.

7 Configure Addresses & Analysis tables for different traffic cases7.1 Explain MSRN/HO number handling in MSC Blades.7.2 Define B-Number Analysis & Routing Cases in a consistent way.7.3 Describe how GTT on SPX and MSC blades should be used.

8 Explain basic traffic cases8.1 Describe common signaling flows on a high level (internal flows in MSC-S BC).

Target audience

The target audience for this course is: System Technician, System Engineer, Network Deployment Engineer

Prerequisites

Those attending need to have competence in MSC-S Blade Cluster Overview and should have either successfully completed the following course or otherwise acquired the relevant pre-knowledge:

MSC-S R14.1 Blade Cluster Overview LZU 108 8003 R1A

Blade Cluster Platform Operation and Maintenance LZU 108 8005 R1A



Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in technical environment using equipment and tools, which can be accessed remotely.






Time schedule



1 Hardware Platform and APZ basics 1.5 hours

1 Cluster concepts 2.5 hours

1 MSC-S R14.1 BC Features 2.0 hours

2 IP on CP basic configuration 2.0 hours

2 Signaling Scenarios - M3UA, SUA usage 3.0 hours

2 / 3 Trunk Routes in the BC 2.0 hours

3 Addresses & Analysis tables 3.0 hours

3 Traffic cases (internal flows in MSC-S BC) 1.0 hour






M-MGw R6.1 Delta

LZU 108 8011 R1A

Description

Do you need to understand the new functionality introduced in the Mobile Media Gateway (M-MGw) Release 6.1?

The course covers the highlights of the new features of MSS Release 6.1. It will give the student knowledge about the enhanced features introduced in the M-MGw R6.1. The students will also be familiar with the different Product Package Configurations, PPC, for the M-MGw R6.1.

Students attending this course should have experience from earlier releases of the M-MGw.

The duration of this course is one day.

Learning objectives


1 Explore the role of the M-MGw in a Mobile Softswitch network1.1 Examine the system overview of the M-MGw R61.2 Briefly explain the MGw functions

2 Present the GMP concept for M-MGw R62.1 Examine the GMP V4.0 for M-MGw R6

3 Survey the enhanced features3.1 Explain the changes to functionality in R6.1, A-interface over IP, Clear Channel Data,

Voiceband data Gateway, Security for IP Transport with Traffic Separation and the related benefits of both the basic and the optional features

Target audience

The target audience for this course is personnel in charge of the operation and configuration of the M-MGW. The target audience is represented by:

System Technicians, System Engineers, Network Design Engineers, Network Deployment Engineers and Service Design Engineer.

Prerequisites

The participants should be familiar with the M-MGw R5 and/or M-MGw R6.0 and have attended the course:

62

GSM/WCDMA M-MGw R5 Operation and Configuration (ILT) LZU 108 6802 and/or M-MGw R6.0 Oeration and Configuration (ILT) LZU 108 7690.



Learning situation


Time schedule



1 Introduction to M-MGw functions and the MSS solution 1 hour

GMP V4 concept for M-MGw R6 2 hours

New and Enhanced features in M-MGw R6.1 3 hours






M-MGw R6.1 Operation and Configuration

LZU 108 8012 R1A

Description

Do you need the skills and knowledge to operate and configure the M-MGw R6.1 in your network?

The M-MGw R6.1 Operation and Configuration course will cover the operational and configuration aspects in the Mobile Media Gateway (M-MGw R6.1). The Ericsson Mobile Softswitch Solution (MSS R6.1) in the core network for GSM and WCDMA accesses will be described from M-MGw’s operational and configuration perspective. The course provides hands-on training with the M-MGw Node Manager, as well as Command Line Interface (CLI) and some applications in Operation Support System-Radio and Core (OSS-RC) related to M-MGw operation and configuration.

The hands-on training covers TDM, ATM and IP transmission solutions. If all solutions (e.g. ATM) are not required the length of the course will be reduced by one day.

Learning objectives

1 Explain the role of M-MGw in the GSM/WCDMA network as defined in the Customer Product Information (CPI) and list the M-MGw features

1.1 Describe the role of M-MGw in an Ericsson Mobile Softswitch Solution 1.2 List the Network Elements in the MSS solution1.3 List and describe different interfaces around a M-MGw node1.4 Explain GCP, Q.2630 and IPBCP on an overview level1.5 State the features that the M-MGw supports

2 Explain the Generic Media Gateway Package (GMP) concepts as per release R62.1 Explain the Connectivity Packet Platform (CPP)2.2 List the M-MGw boards and their function2.3 Explain the different GMP versions2.4 Describe the GMP Hardware Architecture2.5 Describe the GMP cabinet and Subrack configurations for M-MGw

3 Perform basic fault management on a M-MGw as described in the CPI3.1 Explain the O&M architecture for M-MGw3.2 Explain the use of Alex Library Explorer (ALEX) based Customer Product Information

(CPI) documents3.3 Read the Alarm List and Alarm Log to manage faults in M-MGw3.4 Follow an Operational Procedure Information (OPI) to solve an alarm

4 Understand the role of different Management Interfaces for M-MGw4.1 Understand the role of Node Manager4.2 Understand the role of OSS-RC for management of M-MGw4.3 Check and understand existing configuration in a M-MGw using the Node Manager

and/or OSS-RC

64

4.4 Understand the role of Command Line Interface (CLI) and Node Command Line Interface (NCLI) in M-MGw

4.5 List and run some useful CLI and NCLI commands

5 Describe the Configuration Process for M-MGw5.1 Explain the CCR tool5.2 Explain the CCR collection form5.3 Describe the M-MGw Initial Start process5.4 Describe M-MGw Traffic Configuration process

6 Explain the M-MGw configuration and use Node Manager and/or OSS-RC to change or configure parts of the different interfaces

6.1 Describe and configure ATM Transport 6.2 Describe and configure TDM Transport 6.3 Describe and configure IP Transport6.4 Explain and configure the Signaling bearers in M-MGw R6, including SS7 over ATM,

TDM and IP6.5 Explain and configure Q.2630 and GCP 6.6 Explain and define Virtual Media Gateway6.7 Explain and configure MSC Pool Proxy6.8 Explain the role of M-MGw as a Signaling Gateway (including Associated Signaling

Mode), Signaling End Point and Signaling Transfer Point

Target audience

The target audience for this course is: Network Design Engineers, Network Deployment Engineers, System Technicians and System Engineers.

Prerequisites




The length of the course is 4 days. If ATM theory and practical exercises are not required the length of the course is 3 days.

Maximum number of participants, in both cases, is 8.

Learning situation







Time schedule



1Introduction, Network layout, M-MGw features, Product Packaging, Hardware management

3 Hours

(3 Hours)

1 Operation and Maintenance overview in M-MGw R6 node 2 Hours

(2 Hours)

1,2 Exercises (with Node Manager) related to hardware and software management and M-MGw system concepts

4 Hours

(2 Hours)

2 CLI and NCLI theory and related exercises 2 Hours

(2 Hours)

3 Configuration in M-MGw - theory and exercises (with NM) 7 Hours

(3 Hours)

4 Fault Management – Alarm/Event Handling 2 Hours

(2 Hours)

4 OSS-RC applications for M-MGw 3 Hours

(3 Hours)

4 Course wrap-up and evaluation 1 Hour

(1 Hour)






M-MGw Operation with AMOS

LZU 108 8013 R1A

Description

The main focus of this course is to give a detailed survey of the Advanced Managed Object Scripting (AMOS) and the participant will after the course have a broad knowledge about the commands and printouts on the CPP based M-MGw (Mobile Media Gateway) nodes.

This course will give you the opportunity to acquire the specific skills necessary for getting information about the configuration and applications running on the M-MGw node in the MSS network. Hands-on practice in getting configuration in M-MGw nodes is provided, dealing with the operation and maintenance of the M-MGw nodes.

Learning objectives


1 Give a high-level overview of AMOS1.1 Explain and describe the AMOS tool1.2 Describe the basic function of AMOS1.3 List and describe the AMOS command line syntax and regular expressions1.4 Describe the process of getting access to AMOS

2 Describe the relationship between Managed Objects and AMOS2.1 Explain the Managed Object Model concept2.2 Explain and describe the Management, Resource and Service layers2.3 List the AMOS commands used for performance handling2.4 Describe the commands for setting the configuration and environment variables2.5 Describe the use of Mobatch files2.6 Browse MOM from AMOS2.7 Explain how filtering commands work2.8 Describe how to use the offline AMOS mode2.9 Describe how to run MO scripts2.10 Describe how to send COLI commands from AMOS

3 Describe how AMOS applies to CPP Core3.1 Use AMOS commands to get information about HW equipment resources3.2 Describe the file system and software loading3.3 Use AMOS commands to get access to Log files3.4 List the AMOS commands for CV backups and software upgrades3.5 Describe the CPP O&M functions

4 Describe how AMOS applies to CPP NCH (Network and Connection Handling)4.1 Use AMOS commands to obtain a view of the ET boards4.2 Use AMOS commands to obtain a view of the IMA and MSP configurations4.3 Describe the supervision methods of fault management on the physical layer

67

4.4 List the AMOS commands in order to get Synchronization information4.5 List the AMOS commands to obtain a view of the ATM/IP/TDM transport network

configuration4.6 Use AMOS commands to obtain a view of the signaling protocol stack4.7 Use AMOS commands to obtain a view of the ALCAP protocol4.8 Use AMOS commands to obtain a view of Iu/Nb/Mc/A-i/f configurations and status4.9 Use AMOS commands to obtain a view of the M-MGw parameters

Target audience The target audience for this course is personnel in charge of the operation and configuration of the M-MGW. The target audience is represented by:

System Technicians, System Engineers, Network Design Engineers, Network Deployment Engineers, and Service Design Engineer.

Prerequisites

The participants should be familiar with the M-MGw or have attended the course:

M-MGw Operation and Configuration LZU 108 8013.



Learning situation

This course is based on theoretical and practical instructor-led lessons given in classroom and in technical environment using equipment and tools.






Time schedule


Day Topics in the course Estimated time1 Course introduction

AMOS Overview

Managed Objects

Exercises

0.5 hour2 hours

2.5 hours1 hour

2 CPP Core

Exercises

3.5 hours2.5 hours

3 CPP NCH

Exercises

3.5 hours2.5 hours






SIGTRAN Workshop

LZU 108 6809 R3A

Description

When SIGTRAN is introduced in the network it allows transport of SS7 messages over IP. New competencies are required, for implementation and handling of the SIGTRAN protocols, in order to benefit from its advantages. The primary focus of this course is obtaining detailed information on the protocols involved in SIGTRAN and to understand how it is introduced in a network.

The basic concepts and the new terminology are introduced. The SIGTRAN protocol stack and basic signaling flows are explained. The new AXE hardware, the SIGTRAN Link Interface (SLI), is introduced. MML commands needed for hardware and signaling configuration (Data Transcript) and for Operation and Maintenance are dealt with in detail. Similarly, hardware involved and the configuration details for SIGTRAN implementation in the M-MGw R5 are explained.

Learning objectives


1 Explain the SIGTRAN concept

2 Understand and explain the SIGTRAN protocols 2.1 Explain the Stream Control Transmission Protocol (SCTP)2.2 Describe the MTP3 User Adaptation Layer (M3UA)2.3 Relate the MTP2 User Peer-to-Peer Adaptation (M2PA) layer in the context of MSS2.4 Explain the IUA and SUA protocols

3 Discuss SIGTRAN impacts on Redundancy, Security and Quality of Service, Migration and Failover

4 Describe the SIGTRAN Link Interface4.1 Explain the differences between IP in RP and IP stack on CP

5 Relate MML commands for working with SIGTRAN in AXE5.1 Understand the Data Transcript for SIGTRAN5.2 Follow MML printouts to verify the SIGTRAN definitions

6 Review the SIGTRAN implementation possibilities in M-MGw6.1 Recognize the hardware involved in implementing SIGTRAN in the M-MGw6.2 Understand the procedure and the Managed Objects for defining a SIGTRAN link in

the M-MGw

70

Target audience

The target audience for this course is Service Planning Engineer, Service Design Engineer, Network Design Engineer.

Prerequisites

The participants should be familiar with SS7 signaling and with configuring signaling in an MSC or HLR and a M-MGw node.



Learning situation







Time schedule

The time required always depends on the knowledge of the attending participants and the hours stated below can be used as estimate

Day Topics in the course Estimated time1 Introduction 0.5 hours

Stream Control Transmission Protocol (SCTP) 1.0 hourMTP3 User Adaptation Layer (M3UA) 1 hourMTP2 Peer-to-Peer Adaptation (M2PA) LayerIUA and SUA Protocols

0.5 hour0.5 hour

Redundancy 0.5 hoursSecurity and Quality of Service (QoS) 0.3 hoursMigration 0.3 hoursFailover 0.3 hoursSIGTRAN Link Interface (SLI) 0.5 hoursData Transcript (DT) / Operation and Maintenance 1 hour

2 Recognize the hardware involved in implementing SIGTRAN in the M-MGw

0.25 hour

Understand the procedure and the Managed Objects for defining a SIGTRAN link in the M-MGw using the Node Manager

2.5 hours

MTP2 User Peer-to-Peer Adaptation (M2PA) configuration 1 hourISDN User Association (IUA) configuration 1 hourCourse sum-up 0.75 hours






GSM/WCDMA MSC in Pool Introduction

LZU 108 7423 R2A

Description

The introduction of the MSC Pool feature in the Core Network brings flexibility and core network level redundancy in both classical network architectures and Mobile Softswitch Solution (MSS). This creates the need of competence development in order to be able to make best use of this new functionality in the network. This course procures the needed information and competence to operators to support in planning for the introduction of the MSC Pool feature in the network.

Learning objectives


1 Present MSC Pool benefits and impacts1.1 Describe the benefits of introducing this feature into the network.1.2 Describe the impact of this feature to the different network nodes.

2 Present MSC Pool functions in the BSC/RNC2.1 Describe the different states of an MSC node, seen from a BSC and RNC nodes

perspective.2.2 Explain the importance of the use of TMSI.2.3 Describe the meaning of the NRI (Network Resource Identity).2.4 Explain the way a BSC/RNC selects an MSC during registration phase.2.5 Describe the routing of Location Updates and CM Service Requests performed by

BSC/RNC based on NRI.

3 Present MSC Pool functions in the MSC3.1 Describe the functions for enhanced access from outer nodes to an MSC pool in idle

and active state. These are: - Enhanced Cooperating VLR functionality, - Proxy MSC functionality, - Neighboring MSC group functionality and - Handling of handover in non-anchor.

3.2 Briefly explain the main steps of building a pooled network.3.3 Briefly explain introduction of MSC-S BC in a pooled network.3.4 Describe MSC-based Load Re-distribution.

4 Present MSC Pool functions in the M-MGw4.1 Describe the principles of the MSC Pool Proxy feature.

5 Present MSC Pool connectivity options5.1 Explain the basic alternatives for connectivity between the RNC, M-MGw and

MSC/MSC-S, including ATM and IP based transmission.5.2 Explain the basic alternatives for connectivity to PoI, PLMN and other networks (like

IMS), including TDM, ATM and IP based transmission.

73

5.3 Explain dimensioning principles in the configuration of TDM connectivity between the BSC and M-MGw in cases of ATM and IP based signaling.

6 Present OSS-RC support for MSC Pool6.1 Describe the management support functions provided by OSS-RC for the MSC pool

feature.6.2 List main changes in the OSS applications ARNE, CNA and NWS-A to support MSC

Pool feature (for GSM).6.3 List the Use Cases available in the MMCM MiP tool (for WCDMA).

7 Present MSC Pool planning & configuration considerations7.1 Describe the considerations for selecting NRI / NRI Length.7.2 Describe CAP / relativeCapacity allocation principles.7.3 Describe Dimensioning impacts for MSC when MSC Pool is introduced.7.4 Describe of MSC-S Blade Cluster when dimensioning a MSC Pool network,

considering selection of CAP/Relative Capacity values, redundancy considerations, NRI length and allocation, etc.

7.5 Explain MSC Pool Configuration data for MSC.7.6 Explain MSC Pool Migration and Modification procedures.

Target audience

The target audience for this course is personnel, with a general knowledge of the operation of an Ericsson MSC and GSM / WCDMA RAN, that requires a special understanding of the MSC Pool feature.

This audience includes personnel in charge of the operation or engineering of these nodes. For customers this target audience is represented by:• System Technician

• System Engineer

• Service Engineer

• Field Technician

• Network Design Engineer

• Network Deployment Engineer

Prerequisites

The participants should be familiar with the operation of an Ericsson MSC (AXE and IS based), M-MGw, BSC (or RNC) and OSS-RC and have the working experience with the MSC/MSC-S R13.0 related release (or later).







The length of the course is 6 hours and the maximum number of participants is 16

Learning situation


Time schedule


Day Topics in the course Estimated time1 Introduction 1 hour

MSC Pool in the BSC/RNC 30 min

MSC Pool in the MSC 90 min

MSC Pool in the M-MGw (featuring Pool Proxy) 30 min

MSC Pool Connectivity 15 min

MSC Pool, OSS-RC support 15 min

Planning and Configuration 2 hours






APZ 212 55 Operation and Maintenance

LZU 108 6847 R2A

Description

The APZ 212 55 is an essential part of the AXE system, especially as a new platform for the BSCs, in MSC-servers, Telephony Softswich applications and as the SPX (Signalig Proxy) part for the MSC-S Blade Cluster system. It is though very advisable that the operation staff can identify any deviation from the normal working state conditions as soon as it happens, and act in a fast and correct manner.

After finishing this course the students will be able to Operate and Maintain the APZ 212 55. The course contains a balanced description of the classical APZs delivered by Ericsson and the new cost, capacity and size optimized APZ 212 55.

Through practical exercises the participants will gain experience in handling the APZ 212 55 by checking its operational states, feeling how the APZ 212 55 reacts in different situations like a system backup or reloading procedures, and extracting of system logs that can be further used for troubleshooting.

Learning objectives

On completion of this course the participants will be able to:1 Describe the evolution of the APZ 212 series1.1 APZ Evolution1.2 Explain the basic APZ concepts1.3 Indicate the capacity and characteristics of different APZ versions1.4 Discuss the key features of the APZ 212 551.5 Explain the APZ 212 55 architecture1.6 Recognize the APZ subsystems and functions

2 Demonstrate use of the APZ 212 55 Hardware2.1 Identify the hardware structure of the APZ 212 55 on cabinet level2.2 Describe the APZ 212 55 on subrack level2.3 Distinguish the major physical, logical interfaces and manageability functions in the

APZ 212 55 2.4 Recognize the APZ 212 55 from the functional point of view2.5 State the functions of the APZ 212 55 boards CPUB, MAUB and RPBI-S2.6 Describe the RPH concept2.7 State the functions of the eGEM magazine, SCB-RP/4 board and Fan Unit 2.8 Explain the CDU panel indications2.9 Operate the Ethernet RP Bus, RPB-E

3 Discriminate the key features in the software structure of APZ 212 55 3.1 Describe the APZ 212 55 software structure.3.2 Describe the Program Control in AXE3.3 Explain the PlexEngine in APZ 212 55






3.4 Explain how the ASA Compiler operates within PlexEngine3.5 State the functionality and components of APZ-VM 3.6 Examine the memory lay out of APZ 212 55

4 Demonstrate use of the Operation handling concepts of APZ 212 554.1 Describe the main system differences affecting handling4.2 State the normal system operation4.3 Utilize the backup procedure in the APZ 212 554.4 Describe the handling of APZ 212 55 run modes4.5 Handle of Middleware and Firmware4.6 Describe the booting procedure of the CPU4.7 Execute System Load-Reload4.8 Explain the Function Change of Middleware and Firmware

5 Demonstrate use of the Fault handling concepts of the APZ 212 555.1 List the hardware fault recovery processes5.2 Repair faults in APZ 212 55 Hardware5.3 List the Software Fault recovery process5.4 Extract restart information in case of CP Software faults5.5 Differentiate between PLEX Engine fault recovery and PLEX fault recovery5.6 Use the Central Log Handler in APZ 212 55

Target audience

The primary target audience for this course is : System Technicians and System Engineers.

Prerequisites


WCDMA AXE Operation LZU 108 5024/1 R4A or

GSM AXE Operation LZU 108 5024/2 R5A or

AXE Operation and Configuration LZU 108 6145 R2A








Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using APZ 212 55 equipment and tools (WinFiol, ALEX), which can also be accessed remotely.

Time schedule


Day Topics in the course Estimated time1 • Course introduction

• Describe the evolution of APZ 212 series1,5 hour

• Identify the APZ 212 55 hardware and the major interfaces• Detail the APZ 212 55 hardware : CPUB, MAUB, RPBIS

and SCB-RP4 boards

2,5 hours

• Discriminate the key features in the software structure of APZ 212 55

• Explain PlexEngine, the APZ VM, the ASA compiler, and the commercial Operating System for the APZ 212 55

1 hour

• Demonstrate use of the Operation handling concepts of APZ 212 55

• Reload, maintain and dump the APZ 212 55

1hour

2 • Demonstrate use of the Operation handling concepts of APZ 212 55 (continuation)

1 hour

• Demonstrate use of Fault Handling concepts of APZ 21255 • Extract restart information and error logs in case of CP

Software faults

2 hours

• Theoretical exercises : summarization of the main concepts 1 hour• Practical exercises 2 hours

3 • Practical exercises (continuation) 5,5 hours• Course Summary 0,5 hour






APZ 212 60 Operation and Maintenance

LZU 108 7561 R1A

Description

The APZ 212 60 is an essential part of the AXE system, especially as a new platform for the MSC, MSC-servers, HLR and Telephony Softswich applications.

Through practical exercises the participants will gain experience in handling the APZ 212 60 by checking its operational states, feeling how the APZ 212 60 reacts in different situations like a system backup or reloading procedures, and extracting of system logs that can be further used for troubleshooting.

Learning objectives

On completion of this course the participants will be able to:1 Describe the APZ 212 60 in an overview level1.1 Explain the APZ Evolution1.2 Explain the basic APZ concepts 1.3 Explain the APZ 212 60 architecture overview1.4 Indicate the capacity and characteristics of different APZ versions1.5 Discuss the key features of the APZ 212 601.6 Recognize the APZ subsystems and functions

2 Demonstrate use of the APZ 212 60 Hardware2.1 Identify the hardware structure of the APZ 212 60 on cabinet level2.2 Describe the APZ 212 60 on subrack level2.3 State the functions of the APZ 212 60 boards CPUB, MAUB and RPBI-S2.4 State the functions of the eGEM magazine, SCB-RP/4 board and Fan Unit 2.5 Explain the CDU panel indications2.6 Distinguish the major physical, logical interfaces and manageability functions in the

APZ 212 60 2.7 Recognize the APZ 212 60 from the functional point of view2.8 Explain RPB-E and IPonCP features

3 Demonstrate use of the Operation Handling concepts of APZ 212 603.1 Describe the main aspects affecting operation handling3.2 Differentiate the APZ 212 60 operational states (CP, MAU, RPH)3.3 Execute the backup procedure in the APZ 212 603.4 Use the Hardware Configuration Table information3.5 Load the APZ 212 60 Central Processor3.6 Describe the booting procedure of the APZ 212 60 CP






4 Demonstrate use of the Fault handling concepts of the APZ 212 604.1 List the hardware fault recovery processes4.2 Repair hardware faults in APZ 212 60 Hardware4.3 List the Software Fault recovery process4.4 Extract restart information in case of CP Software faults4.5 Differentiate between PLEX Engine fault recovery and PLEX fault recovery4.6 Use the Central Log Handler in APZ 212 60

5 Discriminate the key features in the software structure of APZ 212 60 5.1 Describe the APZ 212 60 software structure.5.2 Explain how the APZ Virtual Machine operates within Plex Engine5.3 Describe the Program Control in AXE5.4 Explain how the ASA Compiler operates within Plex Engine5.5 Examine the memory lay out of APZ 212 605.6 Explain the Program Execution Platform5.7 Identify where the APZ 212 60 Plex Engine software is stored in APG435.8 Explain the Function Change of Middleware and Firmware

Target audience

The primary target audience for this course is : System Technicians and System Engineers.

Prerequisites


WCDMA AXE Operation LZU 108 5024/1 or

GSM AXE Operation LZU 108 5024/2 or

AXE Operation and Configuration LZU 108 6145


The length of the course is 12 hours and the maximum number of participants is 8.

Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using APZ 212 60 equipment and tools (WinFiol, ALEX), which can also be accessed remotely.






Time schedule


Day Topics in the course Estimated time (min)1 • Course introduction

• Describe the evolution of APZ 212 series40

• Identify the APZ 212 60 hardware and the major interfaces• Detail the APZ 212 60 hardware : CPUB, MAUB, RPBIS

and SCB-RP4 boards

60

• Demonstrate use of the Operation handling concepts of APZ 212 60

• Working States and dump the APZ 212 60

60

• Exercises 2002 • Demonstrate use of the Operation handling concepts of

APZ 212 60 (continuation)60

• Demonstrate use of Fault Handling concepts of APZ 21260 • Extract restart information and error logs in case of CP

Software faults

60

• Discriminate the key features in the software structure of APZ 212 60

• Explain PlexEngine, the APZ VM, the ASA compiler

40

• Practical exercises 200• Course Summary 10






AXE 810 Data Transcript

LZU 108 6134 R3A

Description

This course will develop the participant’s current knowledge and understanding of exchange data to a point where he/she will be able to interpret exchange requirements and write the data transcript for an AXE 810.

The participant will have the opportunity for discussion about data transcript production, inputs, flow and ideas. Generally, theoretical lessons will be followed by practical work giving the participant the opportunity to write data transcript from exchange requirements.

Learning objectives


1 Understand the general hardware structure of AXE 8101.1 Understand the AXE modular system architecture 1.2 Understand the APZ control system1.3 List the hardware components of AXE8101.4 Explain the main benefits of AXE 8101.5 Explain the difference compared with BYB5011.6 List the highlights of AXE 810

2 Understand the new features of AXE 8102.1 Understand the basic structure of APG40 and APG432.2 Understand the basic structure of APZ 212 33/C2.3 Understand the basic structure of APZ 212 502.4 Understand the basic structure of APZ 212 552.5 Understand the basic structure of APZ 212 602.6 Explain the function of IPN2.7 Explain the connection of IPN in different APZ version

3 Define the C3 file and other hardware of AXE 8103.1 Explain the inputs and outputs of the Data Transcript process3.2 Use the Customer Product Information (Alex Document Browsers) in order to find

appropriate commands, parameters and parameter values3.3 Explain the process of converting a reference dump into a working dump

4 Perform a Size Alteration4.1 Understand the concept of SAE4.2 Explain the difference between global SAE and local SAE4.3 Understand the manual and automatic SAE function4.4 List a simple DT example






5 Allocate RP and EM5.1 Explain the basic structure of various GDM5.2 List different RP types5.3 List the DT examples of allocation for RP and EM

6 Define the Group Switch and connect Devices6.1 Describe the GEM structure6.2 Describe the structure of GS8906.3 Understand the different capacity configuration of GS8906.4 List the new hardware equipment in GEM6.5 Describe the connection of GDM to the GS8906.6 Describe the definition of BL phone, 6.7 Describe the structure and different configuration of CL8906.8 List the DT example to define GS, SNT, DIP, device and route.6.9 Describer ALI applications and list the DT example to define ATM Link Interface (ALI) 6.10 Describe and list DT for C7 MTP and HSL.6.11 Describer SLI applications and list the DT example to define SLI

7 Define pre A-number and A-number analysis7.1 Understand the basic principle of A-number analysis and A-number pre-analysis7.2 Understand the commands and the parameters in the A-number and A-number pre-

analysis table7.3 List simple DT example for A-number and A-number pre-analysis table

8 Define Pre B-number and B-Number Analysis8.1 Understand the basic principle of B-number analysis and B-number pre-analysis8.2 Understand the commands and the parameters in the B-number and B-number pre-

analysis table8.3 List simple DT example for B-number and B-number pre-analysis

9 Define Routing Case Analysis9.1 Understand the basic principle of routing case analysis9.2 Understand the commands and the parameters in routing case analysis table9.3 List simple DT example for routing case analysis

10 Define End-of-Selection (EOS) Analysis10.1 Understand the basic principle of EOS analysis10.2 Understand the parameters and actions possible to initiate in EOS analysis table10.3 List simple DT example for EOS analysis

11 Define Equal Access11.1 Understand the basic function and structure of equal access carrier analysis11.2 Understand the commands and parameters in the equal access carrier analysis table11.3 List simple DT example for equal access carrier analysis






12 Define Charging Data12.1 Understand the overall charging analysis table12.2 Understand traffic activity analysis, charging case analysis and charging program

analysis12.3 Understand the calendar function12.4 Understand the commands of charging analysis12.5 List DT example for tariff charging

13 Define Access-Barring Analysis and Time-Supervision Analysis13.1 Understand the basic concept of access barring analysis and time supervision13.2 Understand the commands for access barring analysis and time supervision13.3 List DT example of access barring analysis and time supervision analysis

14 Define Announcements14.1 Understand the concept of phrase and announcements14.2 Understand the access to announcement and the route data14.3 List DT example of announcements

Target audience

The target audience for this course is: Network Deployment Engineers and System Engineers.

The target audience for this course is personnel in the network planning or network configuration in the are of Data Transcript.

Prerequisites


AXE 810 Configuration Delta LZU 108 5412



Learning situation


Time schedule








1 • AXE 810 Overview• APZ and APG• Introduction to Data Transcript

2 hours

3 hours

1 hour

2 • Size Alteration Events • Allocation of RP and EM• Group Switch and Connection of Device

2 hours

2 hours

2 hours

3 • Group Switch and Connection of Device (continued)• A number Analysis

4 hours

2 hours

4 • B number Analysis• Routing Case Analysis• End of Selection• Equal Access

2 hours

2 hours

1 hour

1 hour

5 • Charging Analysis• Access Barring and Time Supervision• Announcement

2 hours

2 hours

2 hours






AXE810 Maintenance

LZU1086750 R2A

Description

Do you have questions about faults, alarms? Do you feel afraid of recovering urgent alarms? Don’t you know how to use the tools provided by Ericcson? Some people have the same questions and concerns. Then you should attend this course.

Through case studies, the maintenance of all supported hardware configurations will be covered in this modular course. Each case covers one or more related events and builds on the knowledge learned from previous cases.

Learning objectives


1 Replace plug-in units for various subordinate hardware elements (e.g. RPs, EMs), and execute the repair procedures using local O&M tools.

2 Generate printouts according to a Work Order, using local Operation and Maintenance (O&M) tools and on-line system documentation.

2.1 Log and save printouts, using local O&M tools

3 Locate and identify GSM hardware units, using online documentation.3.1 Determine the order number and release revision of hardware elements, using the

Alex library3.2 Exchange subordinate hardware elements, using online documentation

4 Perform repair sequences on various hardware elements (e.g. RPs, EMs), using WinFIOL / OSS-RC, online documentation, and data from a Work Order.

5 Determine the order and release revision of AXE central elements, using online documentation.

5.1 Exchange hardware units in AXE central elements, using online documentation5.2 Perform repair sequences on AXE central hardware elements, using WinFIOL/ OSS-

RC, online documentation, and data from a Work Order5.3 Generate status printouts of AXE central elements in accordance with a Work Order,

using local O&M tools and online documentation5.4 Determine APZ system status, using visible hardware indicators

6 Locate and identify APG 40 / APG 43 hardware units, using online documentation.6.1 Generate printouts of APG 40 / APG43 system status and hardware elements, using

local O&M tools and online documentation

7 Save a system backup copy on removable media, using online documentation and Work Order data.

7.1 Transfer a file from removable media to hard disk, using online documentation and Work Order data

8 Test load a system backup copy, using online documentation and Work Order data.

9 Perform routine preventive maintenance on the AXE, using online documentation.






10 Perform repair on Sigtran hardware (GARP).

11 Perform repair sequences on BSC-specific hardware elements (TRAU), using WinFIOL/OSS-RC, online documentation, and data from a Work Order.

12 Replace plug-in units for various subordinate hardware elements (e.g. RPs, EMs), and execute the repair procedures using local O&M tools.

13 Replace plug-in units for various central hardware elements (APZ, APG and GPB), and execute the repair procedures using O&M tools.

Target audience


Field Technicians, System Technicians

Prerequisites

Successful completion of the following stream:

AXE Operation and Configuration LZU 108 6145

GSM / WCDMA AXE Operation LZU 108 5024

APG 40 O&M LZU 108 5870

APG 43 O&M LZU 108 7177


The length of the standard course (only one APZ model) is 5 days and for all relevant APZ models is 7 days. The maximum number of participants is 8.

Learning situation

This is a task-oriented learning course based on tasks in the work process given in a technical environment using equipment and tools. Working in groups of two for most events, students are issued various Work Orders to resolve hardware faults, perform hardware replacement, and follow simple non-fault related maintenance routines using the system documentation.

The instructor acts as facilitator, helping students to obtain the required competency and may present theorectical material to support and enhance skills learnt from performing the cases.

Time schedule







Day Topics in the course Estimated time1 • Win Fiol and ALEX

• Hardware handling and Structure (hardware presentation)• AXE Hardware Faults – Control Path (RP, EM Fault)

120 min100 min100 min

2 • GS Fault• AXE Hardware Fault – Speech Fault (DIP, SNT, SDIP

Fault)• CP Status and Basic CP Fault Repair


3 • CP Status and Basic CP Fault Repair• MSC Specific (Optional)or• Telephony Service Specific (Optional)or• BSC Specific (Optional)

240 min120 min

120 min

120 min

4 • CP Stoppage• IO Status and Basic IO Fault Repair• IO Restart and Reload


5 • Backup Handling and Routine Maintenance• Final tests / summary

1 Day






GSM AXE Operation

LZU 108 5024/2 R6A

Description

How the AXE system structure knowledge can facilitate your daily activities? Don´t you know how to configure routes and devices because you are not familiar with operational routines? Many customers do face this situation too.

This course will teach you how to operate the functions of the AXE 810 switch common to all AXE810 applications of a network. When finishing the course the students will have a deeper understanding of operation and configuration activities in AXE810 exchanges in an efficient way.

The practical parts will be performed either in a real exchange, on SEA environment or in a Remote Lab (RTL) with realistic exercises.

Learning objectives


1 Recognize the AXE 810 product structure and the documentation used1.1 Identify the market position for AXE.1.2 Recognize the product structure of AXE.1.3 Recognize the BYB 501 building practice on an overview level.1.4 Identify the main parts of the command code.1.5 Use different parameter variants of standard AXE commands.1.6 Interpret different printouts generated by the system.1.7 Handle WinFIOL to communicate with AXE.1.8 Handle the AXE library as an aid.

2 Demonstrate use of the basic APG functions2.1 Recognize the APG Functions2.2 Access the AXE system through the APG2.3 Identify the APG HW Layout2.4 Utilize the File Management Subsystem

3 Differentiate between the RPs types used in the system 3.1 Handle the RPs on a basic level.3.2 Define EMs controlled by the RPs.3.3 Configure the databases used when defining RPs.






4 Identify the structure of the Group Switch GS8904.1 Operate the Group Switch GS890.4.2 Configure the different parts of the group switch.4.3 Administer the clock function.4.4 Discuss how the network synchronization is dealt with in AXE.4.5 Explain the SNT, DIP and SDIP concepts.4.6 Configure SNTs, DIPs and SDIPs.

5 Implement the necessary exchange data to connect routes and devices5.1 Configure hardware for new routes.5.2 Define routes and devices.5.3 Connect and disconnect devices.5.4 Modify Size Alteration Events on request from a work order.

6 Manage Signaling in AXE810 systems6.1 Identify basic signaling concepts.6.2 Explain the differences between CAS and CCS signaling systems.6.3 State the structure of the CCS.6.4 Define a signaling system no. 7 (SS7) in AXE up to the MTP.

7 Make use of CPs in the APZ 212 family regarding their structure and functionalities7.1 Handle the CPs on a basic level.7.2 Operate the System Backup functions.

8 Correlate the main Analysis tables in AXE8.1 Define data in the (Pre) B-Number Analysis table and check the result. 8.2 Define data in the Route Analysis table and check the result.8.3 Analyze End-of-Selection Analysis table using commands. 8.4 Check data in Charging Analysis.

9 Operate BSC Operation functions on basic level9.1 Describe the BSC specific hardware.9.2 Recognize BSC specific data.9.3 Understand the Managed Object (MO) in BSC.9.4 Analyze the OSS Interface.9.5 Send some BSC commands.

Target audience


System Technicians, System Engineers.

Prerequisites






Successful completion of the following training flow:

GSM Network Fundamentals, Blended Training FAB 102 1465 R1A



Learning situation


Time schedule


Day Topics in the course Estimated time1 • Introduction and Pre-Test

• MML , WinFIOL , AXE Library 6 hs

2 • Understand the I/O system 4 hs3 • Define RP/EMs and SAEs 5 hs4 • Group Switch, SNT & DIP, Clock and Synchronization 6 hs5 • Route and Device Data 6 hs6 • Signaling in AXE 6 hs7 • APZ 212 + Backup Handling 5 hs8 • Analysis in AXE : B-number, Route 6 hs9 • Analysis in AXE : EOS, Charging 4 hs10 • BSC Basic Operations 6 hs






GSM Maintenance MSC/BSC Extended

LZU 108 5031 R6A/2

Description

This course is essential for those wishing to practice implementing their hardware maintenance skills and knowledge on the AXE nodes of the GSM R12/R13 MSC/BSC. Having attended previous courses and acquired the prerequisite knowledge, students on this course, work full-time hands-on in a guided environment to put their prerequisite skills into practice.

Upon completion, you will be able to deal with hardware faults on the central elements of the AXE, like Central Processor, Group Switch and APG 40 or APG43, and follow maintenance routines using system documentation and local operation and maintenance (O&M) tools.

Learning objectives

On completion of this course the participants will be able to: 1 Identify hardware components and interconnections of the relevant Group Switch using

online and exchange documentation.2 Identify the hardware components and interconnections of the Input / Output (IO)

configuration, using O&M tools and online documentation. 3 Detect and solve intermediate level faults in IO hardware, using O&M tools and online

documentation.4 Access and use IO logging functions in the detection and analysis of system faults,

using O&M tools and online documentation.5 Access and use IO file processing functions to gather and distribute essential

exchange data, using O&M tools and online documentation.6 Determine the actions of the Maintenance Subsystem (MAS) in supervising CP

hardware and handling CP faults, using O&M tools, exchange printouts, and online documentation.

7 Determine the MAS actions in CP software supervision and recovery, using O&M tools, online documentation, and direct observation.

8 Handle CP software recovery alarms, using O&M tools and online documentation.9 Handle an intermediate level CP stoppage, using O&M tools, online documentation,

and the CP Test (CPT) system.






Target audience

The target audience for this course is: System Technicians, Field Technicians.

Prerequisites

Successful completion of the following courses/flows:

GSM Network Fundamentals, Blended Training FAB 102 1465

In particular, prior attendance of the following is essential:

GSM Core Network Maintenance LZU 108 5458/2



Learning situation

This is a task-oriented learning course based on tasks in the work process given in a technical environment using equipment and tools.

The instructor will act as a facilitator. The students work independently receiving assistance only where necessary. Instances of pure lecturing will be limited. Hence students have an opportunity in this course to implement concepts learned in previously attended prerequisite courses into practical skills.

Time schedule

The time required always depends on the knowledge of the attending participants and the plan stated below can be used as a guidance.

See following detailed Learning Product Plan:






Day Topics in the course Estimated time1 • Case 1: Group Switch

- Event 1.1: GS 890 Hardware Verification- Event 1.2: GS 890 Fault, MUX3- Event 1.3: GS 890 Fault, CLM- Event 1.4: GS 890 Unit Definition

• Case 2: Hardware- Event 2.1 or 2.2: APG Hardware (40 or 43)- Event 2.3: Check Cable connection in APZ 212 55 or

60- Event 2.4: APZ 212 55 or 60 board positions and diods- Event 2.5: IPMI check in the SCB-RP/4

• Case 3: IO and CP Board Faults- Event 3.1 or 3.2: APG Hardware Faults (40 or 43)

30min30min30min60min


100min

2 - Event 3.1 or 3.2: APG Hardware Faults (40 or 43)- Event 3.3: SCB-RP/4 Repair (for APG43)- Event 3.4: IPMI Firmware upgrade

• Case 4: IO Log Files- Event 4.1 or 4.3: Command Log File APG (40 or 43)- Event 4.2 or 4.4: Audit Log File APG (40 or 43)

• Case 5: Storage Media and Data Collection- Event 5.1 or 5.3: Backup of APG Software (40 or 43)

20min30min30min

120min120min

40min

3 - Event 5.1 or 5.3: Backup of APG Software (40 or 43)- Event 5.2 or 5.4: Collection Fault Data APG (40 or 43)

• Case 6: File Processing- Event 6.1 or 6.2: Transfer Queue to a Destination APG

(40 or 43)• Case 7: Recovery Actions

- Event 7.1: System Recovery- Event 7.2: Escalation Window- Event 7.3: Selective Restart- Event 7.4: Error Intensity Restart- Event 7.5: Recommended Recovery Settings

20min30min

120min

40min40min40min40min30min






4 - Event 7.5: Recommended Recovery Settings • Case 8: Recovery Alarms

- Event 8.1: Alarm System Restart - Event 8.2: Alarm Small Restart is Pending- Event 8.3: Alarm Software Error (Optional)

• Case 9: Forlopp Handling- Event 9.1: Forlopp Duration Supervision- Event 9.2: Recommended Forlopp Functions- Event 9.3: Forlopp Duration Alarm

10min

80min60min60min

60min60min30min

5 - Event 9.3: Forlopp Duration Alarm- Event 9.4: Forlopp Release Alarm

• Case 10: System Stoppage- Event 10.1: System Stoppage APZ 212 33- Event 10.2: System Stoppage APZ 212 33 (FEX)- Event 10.3: System Stoppage APZ 212 40- Event 10.4: System Stoppage APZ 212 40 (FEX)- Event 10.5: System Stoppage APZ 212 50 - Event 10.6: System Stoppage APZ 212 50 (FEX)- Event 10.5: System Stoppage APZ 212 55 or 60 - Event 10.6: System Stoppage APZ 212 55 or 60 (FEX)

30min60min

60min60min60min60min60min60min60min60min






WCDMA AXE Operation

LZU 108 5024/1 R5A

Description

How the AXE system structure knowledge can facilitate your daily activities? Don´t you know how to configure routes and devices because you are not familiar with operational routines? Many customers do face this situation too.

This course will teach you how to operate the functions of the AXE 810 switch common to all AXE810 applications of a network. When finishing the course the students will have a deeper understanding of operation and configuration activities in AXE810 exchanges in an efficient way.

The practical parts will be performed either in a real exchange, on SEA environment or in a Remote Lab (RTL) with realistic exercises.

Learning objectives


1 Recognize the AXE 810 product structure and the documentation used 1.1 Identify the market position for AXE.1.2 Recognize the product structure of AXE.1.3 Recognize the BYB 501 building practice on an overview level.1.4 Identify the main parts of the command code1.5 Use different parameter variants of standard AXE commands1.6 Interpret different printouts generated by the system1.7 Handle WinFIOL to communicate with AXE1.8 Handle the AXE library as an aid.

2 Demonstrate use of the basic APG functions2.1 Recognize the APG Functions2.2 Access the AXE system through the APG2.3 Identify the APG HW Layout2.4 Utilize the File Management Subsystem

3 Differentiate between the RPs types used in the system 3.1 Handle the RPs on a basic level.3.2 Define EMs controlled by the RPs3.3 Configure the databases used when defining RPs






4 Identify the structure of the Group Switch GS8904.1 Operate the Group Switch GS890.4.2 Configure the different parts of the group switch.4.3 Administer the clock function.4.4 Discuss how the network synchronization is dealt with in AXE.4.5 Explain the SNT, DIP and SDIP concepts.4.6 Configure SNTs , DIPs and SDIPs.

5 Implement the necessary exchange data to connect routes and devices5.1 Configure hardware for new routes.5.2 Define routes and devices. 5.3 Connect and disconnect devices.5.4 Modify Size Alteration Events on request from a work order.

6 Manage Signaling in AXE810 systems6.1 Identify basic signaling concepts.6.2 Explain the differences between CAS and CCS signaling systems.6.3 State the structure of the CCS.6.4 Define a signaling system no. 7 (SS7) in AXE up to the MTP.

7 Make use of CPs in the APZ 212 family regarding their structure and functionalities7.1 Handle the CPs on a basic level.7.2 Operate the System Backup functions.

8 Correlate the main Analysis tables in AXE 8.1 Define data in the (Pre) B-Number Analysis table and check the result. 8.2 Define data in the Route Analysis table and check the result.8.3 Analyze End-of-Selection Analysis table using commands. 8.4 Check data in Charging Analysis.

Target audience

The target audience for this course is: System Technicians, System Engineers.

PrerequisitesSuccessful completion of the following training flow:

WCDMA Network Fundamentals, WBL (FAB 102 1316 R1A) or

WCDMA Network Fundamentals, Blended Training (FAB 102 1317 R1A)








Learning situation


Time schedule


Day Topics in the course Estimated time1 • Introduction and Pre-Test

• MML , WinFIOL , AXE Library 6 hs

2 • Understand The I/O System 4 hs3 • Define RP/EMs and SAEs 6 hs4 • Group Switch, SNT & DIP, Clock and Synchronization 6 hs5 • Route and Device Data 6 hs6 • Signaling in AXE 6 hs7 • APZ 212 + Backup Handling 5 hs8 • Analysis in AXE : B-number, Route 5 hs9 • Analysis in AXE : EOS, Charging 4 hs






WCDMA Maintenance MSC Extended

LZU 108 5031 R6A/1

Description

This course is essential for those wishing to practice implementing their hardware maintenance skills and knowledge on the AXE nodes of the WCDMA R12/R13 MSC. Having attended previous courses and acquired the prerequisite knowledge, students on this course, work full-time hands-on in a guided environment to put their prerequisite skills into practice.

Upon completion, you will be able to deal with hardware faults on the central elements of the AXE, like Central Processor, Group Switch and APG 40 or APG43, and follow maintenance routines using system documentation and local operation and maintenance (O&M) tools.

Learning objectives

On completion of this course the participants will be able to:1 Identify hardware components and interconnections of the relevant Group Switch using

online and exchange documentation.2 Identify the hardware components and interconnections of the Input / Output (IO)

configuration, using O&M tools and online documentation. 3 Detect and solve intermediate level faults in IO hardware, using O&M tools and online

documentation.4 Access and use IO logging functions in the detection and analysis of system faults,

using O&M tools and online documentation.5 Access and use IO file processing functions to gather and distribute essential

exchange data, using O&M tools and online documentation.6 Determine the actions of the Maintenance Subsystem (MAS) in supervising CP

hardware and handling CP faults, using O&M tools, exchange printouts, and online documentation.

7 Determine the MAS actions in CP software supervision and recovery, using O&M tools, online documentation, and direct observation.

8 Handle CP software recovery alarms, using O&M tools and online documentation.9 Handle an intermediate level CP stoppage, using O&M tools, online documentation,

and the CP Test (CPT) system.

Target audience

The target audience for this course is: System Technicians, Field Technicians.






Prerequisites

Successful completion of the following courses/flows:

WCDMA Network Fundamentals, WBL FAB 102 1316 orWCDMA Network Fundamentals, Blended Training FAB 102 1317

In particular, prior attendance of the following is essential:

WCDMA Core Network Maintenance LZU 108 5458/1



Learning situation

This is a task-oriented learning course based on tasks in the work process given in a technical environment using equipment and tools.

The instructor will act as a facilitator. The students work independently receiving assistance only where necessary. Instances of pure lecturing will be limited. Hence students have an opportunity in this course to implement concepts learned in previously attended prerequisite courses into practical skills.

Time schedule

The time required always depends on the knowledge of the attending participants and the plan stated below can be used as a guidance.

See following detailed Learning Product Plan:






Day Topics in the course Estimated time1 • Case 1: Group Switch

- Event 1.1: GS 890 Hardware Verification- Event 1.2: GS 890 Fault, MUX3- Event 1.3: GS 890 Fault, CLM- Event 1.4: GS 890 Unit Definition

• Case 2: Hardware- Event 2.1 or 2.2: APG Hardware (40 or 43)- Event 2.3: Check Cable connection in APZ 212 60- Event 2.4: APZ 212 60 board positions and diods- Event 2.5: IPMI check in the SCB-RP/4

• Case 3: IO and CP Board Faults- Event 3.1 or 3.2: APG Hardware Faults (40 or 43)



100min

2 - Event 3.1 or 3.2: APG Hardware Faults (40 or 43)- Event 3.3: SCB-RP/4 Repair (for APG43)- Event 3.4: IPMI Firmware upgrade

• Case 4: IO Log Files- Event 4.1 or 4.3: Command Log File APG (40 or 43)- Event 4.2 or 4.4: Audit Log File APG (40 or 43)

• Case 5: Storage Media and Data Collection- Event 5.1 or 5.3: Backup of APG Software (40 or 43)

20min30min30min

120min120min

40min

3 - Event 5.1 or 5.3: Backup of APG Software (40 or 43)- Event 5.2 or 5.4: Collection Fault Data APG (40 or 43)

• Case 6: File Processing- Event 6.1 or 6.2: Transfer Queue to a Destination APG

(40 or 43)• Case 7: Recovery Actions

- Event 7.1: System Recovery- Event 7.2: Escalation Window- Event 7.3: Selective Restart- Event 7.4: Error Intensity Restart- Event 7.5: Recommended Recovery Settings

20min30min

120min

40min40min40min40min30min






4 - Event 7.5: Recommended Recovery Settings • Case 8: Recovery Alarms

- Event 8.1: Alarm System Restart - Event 8.2: Alarm Small Restart is Pending- Event 8.3: Alarm Software Error (Optional)

• Case 9: Forlopp Handling- Event 9.1: Forlopp Duration Supervision- Event 9.2: Recommended Forlopp Functions- Event 9.3: Forlopp Duration Alarm

10min

80min60min60min

60min60min30min

5 - Event 9.3: Forlopp Duration Alarm- Event 9.4: Forlopp Release Alarm

• Case 10: System Stoppage- Event 10.1: System Stoppage APZ 212 33- Event 10.2: System Stoppage APZ 212 33 (FEX)- Event 10.3: System Stoppage APZ 212 40- Event 10.4: System Stoppage APZ 212 40 (FEX)- Event 10.5: System Stoppage APZ 212 50 - Event 10.6: System Stoppage APZ 212 50 (FEX)- Event 10.5: System Stoppage APZ 212 60 - Event 10.6: System Stoppage APZ 212 60 (FEX)

30min60min

60min60min60min60min60min60min60min60min






IS 3.1 Overview

LZU 1087566 R1A

Description

This course gives an introduction to the Integrated Site (IS). It answers the questions: “What is IS?” and “Why use IS?”. The drivers for IS, the scope and the benefits are highlighted together with some examples of IS application blade systems. In addition to the general principles, some technical details are presented to provide a bridge for further studies of the Integrated Site concept. The course will also cover the differences between IS 3.1 and the previous version, IS 2.0.

Learning objectives


1 Understand the IS concept in general terms1.1 Describe the background to the IS concept 1.2 Explain the IS basic concept and give examples of possible site solutions1.3 Understand the benefits and drivers associated with IS1.4 Explain the consequences of the IS concept and list areas that are affected by the IS

concept1.5 Explain basic terminology related to IS1.6 Understand the meaning of the concepts IS Framework and IS Infrastructure1.7 List the main differences between IS 2.0 and 3.1

2 Give an overview of IS from the equipment view2.1 Describe the equipment practice employed in IS (EGEM)2.2 Describe the hardware employed for the infrastructure Blade Systems2.3 Explain the use of link aggregation in IS2.4 Describe the Multiple Subrack domain solution

3 Have basic knowledge about management solutions in IS3.1 Give an introduction to the IS Management System (ISM), the Common Management

Framework (CMF) and related user interfaces3.2 Give an introduction to IS common HW and SW management3.3 Describe the purpose and function of ISCO and BSOM3.4 Explain the purpose and function of IS common parameters3.5 Give an introduction to the CPI documentation

4 Describe IS from the network and security views4.1 Get an idea of the use of logical networks, subnets, subnet segments and VLANs4.2 Have a basic knowledge about the layer 2 switching and layer 3 routing

implementation in IS4.3 Describe the purpose of the predefined internal subnets and VLANs4.4 Get a basic understanding of IP Addressing in IS4.5 Give an introduction to Quality of Service (QoS) and Class of Service (CoS) treatment

in IS4.6 Give an introduction to security implementation in IS






5 Have knowledge about IS 3.1 solution scenarios5.1 Describe the solutions for MSC-S, IMS and TSS on IS

Target audience

The target audience for this course is: Network Design Engineer, Network Deployment Engineer, System Technician, System Engineer, Field Technician, System Administrator, Application Developer, Business Developer, Customer Care Administrator

Customers and Ericsson Internal

Prerequisites


LZU102397 IP Networking (or similar knowledge)



Learning situation

Instructor Led Training (ILT). This course is based on theoretical instructor-led lessons.

Time schedule



1 Introduction to IS (chapter 1) 1,5h

1 Equipment view (chapter 2) 1h

1 Management solutions in IS (chapter 3) 1h

1 Network and security views (chapter 4) 1h

1 Solution Scenarios for IS based nodes (chapter 5) 1h

1 Summary 0,5h






IS 3.1 Operation and Configuration

LZU 108 7567 R1A

Description

This course provides participants with the skills and knowledge needed for managing an IS domain by exploring the elements involved in operation and maintenance, and network configuration. This includes fault management, network, hardware and software configuration and management. Each task is complemented by practical exercises on a real IS site. Participants will complete practical site management exercises using on-line documentation and the recommended IS Management Interfaces. The training consists of both theory and practical exercises.

Learning objectives

On completion of this course the participants will be able to

1 Describe and handle the recommended IS infrastructure Management Interfaces 1.1 Connect to the SIS (ISM) and EXB using the recommended management interfaces1.2 Be familiar with the structure of the ISM GUI 1.3 Use the on-line documentation

2 Manage Users and Accounts2.1 Handle user accounts, access permissions and password settings in the ISM

3 Manage Software3.1 Understand the function of the Private Software Management3.2 Understand the difference between software group (swg) and software delivery

package, blade swg and BS swg3.3 Download new software3.4 Perform software updates3.5 Describe in service upgrade from IS 2.0 to IS 3.13.6 Create and restore a blade system backup and site backup3.7 Manage backups (housekeeping of backups)3.8 Keep track of installed software

4 Manage Hardware4.1 Understand the role of the shelf manager4.2 Verify installed hardware in the ISM-GUI (sub-racks, blade systems and blades)4.3 Configure new installed HW4.4 Check valid blade types in the ISM-GUI4.5 Transfer a copy of the Hardware Inventory to a remote location4.6 Lock and unlock blades and blade systems4.7 Understand the procedure for replacing a faulty blade






4.8 Be familiar with visual indicators on the boards4.9 Be familiar with performing in-service upgrades of infrastructure HW4.10 Understand the function of Private HW Management

5 Manage Log Files5.1 View BS log files in the ISM GUI5.2 Transfer ASI and BS log files to a remote location5.3 Know what types of log files that are handled by the IS central log service

6 Handle Events and Alarms6.1 Understand the role of the IS Fault Management function6.2 Explain the function of the LAN FM6.3 Check alarm and event notifications6.4 Find relevant information on how to act on an alarms 6.5 Understand how alarms are ceased6.6 Transfer alarm and event logs6.7 Create user defined alarm and event logs6.8 Explain how disc usage is controlled in the IS

7 Set up and verify Network Configuration and ISP7.1 Configure and verify IS and BS Logical Networks, Subnets, Segments and VLANs7.2 Use the performance monitoring services for the EXB and MXB 7.3 Know how to read and clear ISP counters7.4 Describe the purpose of the IS common parameters and BS parameters7.5 Explain L2 Switching and the use of link aggregation in the IS7.6 Understand how to configure L2 switching and LAG7.7 Define traffic classes for IS common resources7.8 Describe the mapping between IS IP traffic classes and IS LAN traffic classes7.9 Describe handling of Diffserv (Differentiated services) in IS

Target audience

The target audience for this course is: System Technician, System Engineer andField Technician, customers or Ericsson internal.






Prerequisites


LZU102397 IP Networking (or similar knowledge)

LZU1087566 IS 3.1 Overview.


The length of the course is 2 days, and the maximum number of participants is 8.

Learning situation

Instructor Led Training (ILT). This course is based on theoretical instructor-led lessons and practical / hands-on exercises on IS systems.

Time schedule


Day Topics in the course Estimated time1 Theory

• Introduction• Management Interfaces• Manage Users and Accounts• Software Management • Hardware Management

3 h

1 Exercises

• Management Interfaces• Manage Users and Accounts• Software Management • Hardware Management: Identify HW

3h






2 Theory

• Manage Log Files• Handle Event and Alarms• Set up and verify Network Configuration

3 h

2 Exercises

• Hardware Management: Configure new HW• Manage Log Files• Handle Event and Alarms• Set up and verify Network Configuration

3 h






Iu over IP in MSS

LZU 108 7425 R1A

Description

As Ericsson’s mobile network solution evolves towards an ‘all IP vision’, the upgrading of the Iu-CS interface to support IP transport for both control plane and user plane traffic is the next step in that evolution.

This course addresses the changes to the mobile network in terms of the Iu-CS interface protocol layer adaptations as well as configuration of the interface of the MSC-S and M-MGw nodes.

Learning objectivesUpon completion of this course, the students will be able to:

1 Describe the Iu-CS interface1.1 Introduce Iu over IP 1.2 List the Operator Benefits1.3 Describe the Iu over IP Interface

2 Describe the protocols used for Iu-CS user plane traffic2.1 Examine the protocols used for Iu-CS control plane traffic2.2 Review the interfaces that handle Iu traffic in the MSC-S2.3 Review the interfaces that handle Iu traffic in the M-MGw

3 Describe QoS for Iu over IP3.1 Discuss the QoS mechanisms in MSS3.2 Identify how VLAN tagging and traffic separation works3.3 Discuss DiffServ and DSCP/ECN marking3.4 Discuss IEEE 802.1p marking3.5 Describe the IP admission control mechanisms (SAC and MBAC)3.6 Identify the bandwidth requirements for IP payload3.7 Discuss jitter compensation in the M-MGw3.8 Discuss performance measurement in the M-MGw

4 Establish the steps to configure Iu-CS over IP 4.1 Explain how the Iu-CS over IP interface is configured on the MSC-S4.2 Explain how the Iu-CS over IP interface is configured on the M-MGw4.3 Explain how QoS is configured on the MSC-S4.4 Explain how QoS and admission control is configured on the M-MGw

5 Describe Iu-CS over IP Bearer Establishment5.1 Examine Iu-CS control plane establishment5.2 Analyze VoIP on the Iu-CS interface






5.3 Look at an Iu-CS Call Flow

Target audience


System Engineer, Network Deployment Engineer, Network Design Engineer.

Prerequisites

Successful completion of the following courses:• GSM System Survey LZU108 852

• WCDMA MSS R5 Introduction LZU 108 6806

• SIGTRAN Workshop LZU 108 6809

The participants should be familiar with IP Networking, VoIP, SS7, SIGTRAN, GSM/WCDMA M-MGW R5 Operation and Configuration and WCDMA MSC-S R13.2 Configuration.



Learning situation


Time schedule

The time required always depends on the knowledge of the attending participants and the hours stated below can be used as estimate. (This paragraph is mandatory).

Day Topics in the course Estimated time1 • Iu-CS over IP interface description .5 hours

• Iu-CS protocol stacks 1.75 hours

• QoS for Iu over IP 1 hour

• Configure Iu-CS over IP 1.75 hours

• Iu-CS over IP Bearer Establishment 1 hour






M-PBN 2010A Concepts - Circuit Switched - SmartEdge Track

LZU 108 8043 R1A

Description

This course provides an insight and understanding of the M-PBN 2010A architecture, concepts and design.

You will learn about the scope of the M-PBN 2010A reference network based on Smartedge, the products involved as well as applied concepts and designs.

Learning objectives


1 Explain the overview of the M-PBN 2010A 1.1 Explain the challenges faced in regards to the mobile operators’ backbone

infrastructure1.2 List the advantages of design modularity

2 Explain the M-PBN 2010A solution and products2.1 Explain M-PBN 2010A solution variants2.2 Identify the infrastructure nodes in the M-PBN 2010A model

3 Explain the M-PBN 2010A Reference Network design3.1 Explain the network connectivity and site infrastructure requirements

4 Explain the basics of the technology used in the M-PBN 2010A4.1 Explain IP Routing and Routing Protocols, VPN Technology, and security concepts in

IP

5 Explain Site Infrastructure and Transport Backbone scope, requirements and limitations

5.1 Describe Network Modularization5.2 Identify M-PBN Site Switch and Router options5.3 Describe redundancy mechanisms for high availability5.4 Describe VLAN traffic separation principles and security design5.5 Describe M-PBN intra-site and inter-site connectivity choices5.6 Explain IGP, iBGP and Client Network routing choice

6 Illustrate IP/MPLS backbone design6.1 Explain the chosen solution in Mobile-PBN IP/MPLS transport backbone design6.2 Describe Entry Level Site Connectivity

7 Discuss Quality of Service7.1 Explain the general QoS purpose7.2 Describe 3GPP QoS model, M-PBN QoS solution and SmartEdge QoS solution

8 Understand SmartEdge Integrated Routing and Bridging (IRB) 8.1 Describe BVI port feature in M-PBN

9 Explain M-PBN 2010A Circuit Switch solution scope and requirement






9.1 Describe CS connectivity to IP transport backbone9.2 Describe the connectivity to all nodes

10 Explain MSS R6.0 IP Signaling10.1 Understand SCTP, M3UA , M2PA and MTP3b layer scenarios10.2 Understand AoverIP concept 10.3 Describe PRA implementation in MPBN10.4 Understand MSC-BC implementation10.5 Understand implementation of IUPCH in MSC-S R14.110.6 Understand network redundancy10.7 Understand the operator’s network scenario

11 Explain MSS R6.0 IP Transport11.1 Describe SIP/SIP-I Inter-working Principle11.2 Describe VLAN and VPN architecture for SIP and MSS11.3 Describe IPX Connectivity

12 Explain MSS SIP Interworking scenarios12.1 Describe the UDC Design and implementation

13 Discuss Network View Overview13.1 Describe the various Network Modules within the M-PBN 2010A design solution

14 Understand the new Security Solution as part of the Ericsson design in M-PBN14.1 Describe the Security Domain Network Security and Design Options available.14.2 Describe the Security Services applied for different traffic types

15 Illustrate O&M Network design as part of the Ericsson design in M-PBN15.1 Illustrate O&M Network design as part of the Ericsson design in M-PBN 2010A15.2 Describe O&M network used for transport of management traffic 15.3 Describe SmartEdge O&M Solution

16 Describe the charging solution for M-PBN 2010A16.1 Describe the Charging Solution for M-PBN 2010A16.2 Describe integration of Charging System and Multi-Mediation16.3 Describe charging solutions based on SASN or SACC16.4 Describe charging systems for Core Network Elements

Target audience

The target audience for this course is: Network Design Engineer, Network Deployment Engineer, Service Design Engineer, Service Deployment Engineer, Service Planning Engineer, System Technician, System Engineer, Field Technician, Service Planning Engineer, Service Engineer

Prerequisites

The participants should be familiar with...or Successful completion of the following courses: Competence in IP (MPLS VPNs, L2VPNs, IP QoS, routing (OSPF, BGP, IS-IS),

VLAN tagging, etc

Competence in ATM (AAL2, AAL5, QoS)






Competence in CS and PS for WCDMA and GSM (Core Network Features of GSNs, MSS including Interfaces, routing features, O&M).

Competence in SS7 Signaling and SIGTRAN.



Learning situation

This course is based on theoretical instructor-led lessons given in a classroom.

Time schedule


1 • Overview

• Overview of M-PBN 2010A 1 hour

• M-PBN 2010A Solution and Products 1 hour

• M-PBN 2010A Reference Network Designs 2 hours

• Basic Technology used in M-PBN 2010A 2 hours

2 • Site Infrastructure & Transport Backbone

• Scope, Requirement & Limitation 2 hours

• IP/MPLS backbone 2 hours

• Quality of Service 2 hours

3 • Circuit Switched

• Scope and Requirement 1 hour

• MSS R6.0 IP Signaling and Transport 3 hours

• MSS SIP Interworking scenarios 1.5 hour

• UDC IP Connectivity 0.5 hour

4 • Network View

• Security Solution 2 hours

• O&M Network Design 2 hours

• Charging Solution 2 hours






M-PBN 2010A Concepts - Circuit Switched - Juniper Track

LZU 108 8042 R1A

Description

This course provides an insight and understanding of the M-PBN 2010A architecture, concepts and design.

This course cover the scope of the M-PBN 2010A Circuit Switched network, the products involved as well as applied concepts and designs. On top of that, the content also includes Overview, Network View and Transport backbone of M-PBN 2010A using Juniper products.

Learning objectives


Overview

1 Explain the overview of the M-PBN 2010A 1.1 Explain the challenges faced in regards to the mobile operators’ backbone

infrastructure1.2 List the advantages of design modularity

2 Explain the M-PBN 2010A solution and products2.1 Explain M-PBN 2010A solution variants2.2 Identify the infrastructure nodes in the M-PBN 2010A model

3 Explain the M-PBN 2010A Reference Network design3.1 Explain the network connectivity and site infrastructure requirements

4 Explain the basics of the technology used in the M-PBN 2010A4.1 Explain IP Routing and Routing Protocols, VPN Technology, and security concepts in

IP

Transport Backbone

5 Explain Site Infrastructure and Transport Backbone scope, requirements and limitations

5.1 Describe Network Modularization5.2 Identify M-PBN Site Switch and Router options5.3 Describe redundancy mechanisms for high availability5.4 Describe VLAN traffic separation principles and security design5.5 Describe M-PBN intra-site and inter-site connectivity choices5.6 Explain IGP, iBGP and Client Network routing choice

6 Illustrate IP/MPLS backbone design6.1 Explain the chosen solution in Mobile-PBN IP/MPLS transport backbone design






7 Discuss Quality of Service7.1 Explain the general QoS purpose

Circuit Switched

8 Explain M-PBN 2010A Circuit Switch solution scope and requirement8.1 Describe CS connectivity to IP transport backbone8.2 Describe the connectivity to all nodes

9 Explain MSS R6.0 IP Signaling9.1 Understand SCTP, M3UA , M2PA and MTP3b layer scenarios9.2 Understand A over IP concept 9.3 Describe PRA implementation in MPBN9.4 Understand MSC-BC implementation9.5 Understand implementation of IUPCH in MSC-S R14.19.6 Understand network redundancy9.7 Understand the operator’s network scenario

10 Explain MSS R6.0 IP Transport10.1 Describe SIP/SIP-I Inter-working Principle10.2 Describe VLAN and VPN architecture for SIP and MSS10.3 Describe IPX Connectivity

11 Explain MSS SIP Interworking scenarios11.1 Describe the UDC Design and implementation

Network View

12 Discuss Network View Overview12.1 Describe the various Network Modules within the M-PBN 2010A design solution

13 Understand the new Security Solution as part of the Ericsson design in M-PBN13.1 Describe the Security Domain Network Security and Design Options available.13.2 Describe the Security Services applied for different traffic types

14 Illustrate O&M Network design as part of the Ericsson design in M-PBN14.1 Illustrate O&M Network design as part of the Ericsson design in M-PBN 2010A14.2 18.2 Describe O&M network used for transport of management traffic

15 Describe the charging solution for M-PBN 2010A15.1 Describe integration of Charging System and Multi-Mediation15.2 Describe charging solutions based on SASN or SACC15.3 Describe charging systems for Core Network Elements

Target audience






The target audience for this course is: Network Design Engineer, Network Deployment Engineer, Service Design Engineer, Service Deployment Engineer, Service Planning Engineer, System Technician, System Engineer, Service Planning Engineer, Service Engineer

Prerequisites

The participants should be familiar with...or Successful completion of the following courses: Competence in IP (MPLS VPNs, L2VPNs, IP QoS, routing (OSPF, BGP, IS-IS),

VLAN tagging, etc

Competence in ATM (AAL2, AAL5, QoS)

Competence in CS and PS for WCDMA and GSM (Core Network Features of GSNs, MSS including Interfaces, routing features, O&M).

Competence in SS7 Signaling and SIGTRAN.



Learning situation

This course is based on theoretical instructor-led lessons given in a classroom.






Time schedule



1 Overview

Overview of the M-PBN 2010A 1 hour

• M-PBN 2010A solution and products 1 hour

• M-PBN 2010A Reference Network design 2 hours

• Basics of the technology used in the M-PBN 2010A 2 hours

2 • Transport Backbone

• Site Infrastructure and Transport Backbone scope, requirements and limitations

3 hours

• IP/MPLS backbone design 2 hour

• Quality of Service 1 hour

3 • Circuit Switched

• M-PBN 2010A Circuit Switch solution scope and requirement

1 hour

• MSS R6.0 IP Signaling 3 hours

• MSS R6.0 IP Transport 1 hour

• MSS SIP Interworking scenarios 1 hour

4 • Network View

• Network View Overview 1 hour

• Security Solution as part of the Ericsson design in M-PBN 1 hour

• O&M Network design as part of the Ericsson design in M-PBN

2 hours

• Charging solution for M-PBN 2010A 2 hours






IP Networking

LZU 102 397 R5A

Description

This course will give the students an insight and understanding of the TCP / IP protocol stack from the physical layer to the application layer. The students will learn the operation of different protocols and applications within the TCP / IP suite such DHCP, DNS, NFS, NIS, NTP, HTTP, SMNP, SMTP, Telnet, FTP, TFTP and RTP. Students will learn about IP addresses, both classful and classless (CIDR) and how subnetting / aggregation and VLSM operates. Students will learn about different network devices and will get a detailed understanding of LAN Switching, Routing and Routing protocols. The hands-on exercises and analysers are used to facilitate the understanding of theory sessions.

Learning objectives

On completion of each module the participants will be able to: 1 List and describe the IP networking including the involved Bodies.1.1 List the functions of the different bodies involved in IP standards / RFCs.1.2 Analyze the OSI reference model and how it relates to the TCP / IP stack.1.3 Explain Ethernet as Physical and Data Link Layer: MAC Address, CSMA/CD

principles, Fast Ethernet, Gigabit Ethernet and speed negotiation.1.4 Explain the operation of Hubs, Switches and Routers.1.5 Explain Wireless LANs.1.6 Explain IP Protocol.1.7 Explain IPv4 packet structure, protocol header and features.1.8 Explain VLSM, CIDR, Subnetting, aggregation, NAT and NAPT.1.9 Explain ICMP protocol, ping and traceroute.1.10 Explain IGMP protocol.1.11 Perform exercises configuring IPv4 addresses, and check connectivity.1.12 Demonstrate IPv6 packet structure, protocol header, features.

2 Explain and compare the transport protocols.2.1 Explain TCP, UDP and SCTP protocol structures, headers and functionality.

3 List the applications protocols.3.1 List and explain the operation of different protocols / applications such as DHCP, DNS,

NFS, NIS, NTP, HTTP, SMNP, SMTP, Telnet, FTP, TFTP and RTP.

4 Describe IP Switching and Routing Protocols and perform exercises using Netsim Simulator.

4.1 Explain and perform exercises about ARP.4.2 Explain and perform exercises of VLANs.






4.3 Explain the purpose of Spanning Tree Protocol (STP).4.4 Explain the operation of Static and Dynamic routing protocols.4.5 Perform Static routing exercises.4.6 List the differences between Vector Distance and Link State protocols.4.7 Explain RIP routing protocol.4.8 Explain OSPF routing protocol.4.9 Explain BGP routing protocol.4.10 Explain IS-IS routing protocol.4.11 Perform routing Protocol exercises.

Target audience

The target audience for this course are personnel who are involved in IP networking or those who require more knowledge on IP addressing, application and routing protocols.

Prerequisites

There are no pre-requisites.



Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using equipment or simulation tools.






Time schedule


Day Short description of the topics in the course Estimated time1 • List the functions of the different Standard Bodies

involved in IP Standards / RFCs0,5 h

• Analyze the OSI Reference Model and how it relates to the TCP / IP stack

1,0 h

• Explain Ethernet as Physical and Data Link Layer: MAC Address, CSMA/CD principles, Fast Ethernet, Gigabit Ethernet and speed negotiation

1,5 h

• Explain the operation of Hubs, Switches and Routers 2,0 h• Explain Wireless LANs 0,5 h• Explain IP Protocol 0,5 h

2 • Explain IPv4 packet structure, protocol header and features

1,0 h

• Explain VLSM, CIDR, Subnetting, aggregation, NAT and NAPT

1,0 h

• Explain ICMP protocol, ping and traceroute• Explain IGMP protocol

1,0 h

• Perform exercises configuring IPv4 addresses, and check connectivity

2,5 h

• Demonstrate IPv6 packet structure, protocol header, features

0,5 h

3 • Explain TCP, UDP and SCTP protocol structures, headers and functionality

2,0 h

• List and explain the operation of different protocols / applications such as DHCP, DNS, NFS, NIS, NTP, HTTP, SMNP, SMTP, Telnet, FTP, TFTP and RTP

2,0 h

• Explain and perform exercises about ARP 2,0 h4 • Explain and perform exercises of VLANs 3,0 h

• Explain the purpose of Spanning Tree Protocol (STP) 0,5 h• Explain the operation of Static and Dynamic routing

protocols0,5 h

• Perform Static routing exercises 1,0 h• List the differences between Vector Distance and Link

State protocols1,0 h

• Explain RIP routing protocol 1,0 h5 • Explain OSPF routing protocol 1,5 h

• Explain BGP routing protocol 0,5 h• Explain IS-IS routing protocol 0,5 h• Perform routing protocol exercises 2,5 h






IP Quality of Service and MPLS

LZU 108 7716 R1A

Description

This course will give the students an insight and understanding of QoS. The students will learn the operation of QoS supporting IP Protocols and MPLS. The hands-on exercises are used to facilitate the understanding of theory sessions.

Learning objectives

On completion of each module the participants will be able to:1 Understand how Quality of Service (QoS) works1.1 Explain QoS Fundamentals and QoS related Protocols1.2 Analyze the enhancement of the IP networks to support transmission of Real Time

data1.3 Describe QoS Basic Concepts1.4 Describe QoS Architectures1.5 Describe QoS Mechanisms1.6 Explain Resource Reservation Protocol (RSVP) – RFC 22051.7 Explain Basic MPLS Concepts1.8 Describe MPLS Labels and Label Stack1.9 Explain MPLS Applications1.10 Describe Generalized Multiprotocols Label Switching – GMPLS1.11 Perform practical exercises covering Class Based Marking (CBM) using IP

Precedence, DSCP and basic MPLS setup

Target audience

The target audience for this course is the staff involved in IP networking and require more knowledge on IP networks to guarantee quality of service.

Prerequisites

Successful completion of the following course or equivalent knowledge:

IP Networking, LZU 102 397 R5A








Learning situation


Time schedule


Day Short description of the topics in the course Estimated time

1 • Explain QoS Fundamentals and QoS related Protocols 0.3 h

• Analyze the enhancement of the IP networks to support transmission of Real Time data

0.2 h

• Describe QoS Basic Concepts 0.5 h

• Describe QoS Architectures 0.5 h

• Describe QoS Mechanisms 1.0 h

• Explain Resource Reservation Protocol (RSVP) 1.0 h

• Explain Label Distribution Systems (LDP, RSVP-TE, BGP)

1.5 h

1, 2 • Explain Basic MPLS Concepts 1.5 h

• Describe MPLS Labels and Label Stack 1.0 h

• Explain MPLS Applications 1.5 h

• Describe Generalized Multiprotocols Label Switching GMPLS

1.0 h

• Perform practical exercises covering Class Based Marking (CBM) using IP Precedence, DSCP and MPLS

2.0 h






IP Security

LZU 108 7717 R1A

Description

This course will give the students an insight and understanding of Security issues. The students will learn the operation of Security topics such as authentication, confidentiality, and integrity. The hands-on exercises are used to facilitate the understanding of theory sessions.

Learning objectives

On completion of each module the participants will be able to:

1 Understand how IP Security (IP Sec) works1.1 Analyze the existing security threats types1.2 Explain Access control lists (ACL)1.3 Explain the purpose and use of Firewalls1.4 Explain Encryption techniques1.5 Identify different Security Services1.6 Explain how Virtual Private Networks (VPN) operate1.7 Explain IP Security (IPSec) – RFC 43011.8 Explain Authentication Header (AH) – RFC 43021.9 Explain Encapsulating Security Payload (ESP) – RFC 43031.10 Explain Internet Key Exchange (IKE) – RFC 2409 v1/RFC 4306 v21.11 Show some Transport Layer Security Protocols (SSL and TLS) – RFC 2246v1/RFC

4346 v1.11.12 Perform practical exercises covering the configuration of an IPSec VPN tunnel (Phase

I and Phase II negotiation)

Target audience

The target audience for this course is the staff involved in IP networking and require more knowledge on IP networks to guarantee security.

Prerequisites










Learning situation


Time schedule



1 • Analyze the existing security threats types 1.0 h

• Explain Access control lists (ACL) 1.0 h

• Explain the purpose and use of Firewalls 1.0 h

• Explain Encryption techniques 1.0 h

• Identify different Security Services 1.0 h

• Explain how virtual Private Networks (VPN) operate 1.0 h

2 • Explain IP Security (IPSec) 1.0 h

• Explain Authentication Header (AH) 1.0 h

• Explain Encapsulating Security Payload (ESP) 1.0 h

• Explain Internet Key Exchange (IKE) 1.0 h

• Show some Transport Layer Security Protocols (SSL and TLS)

1.0 h

• Perform practical exercises covering the configuration of an IPSec VPN tunnel (Phase I and Phase II negotiation)

1.0 h






Voice and Video over IP

LZU 108 7718 R1A

Description

This course will give the students an insight and understanding of Voice and Video over IP. The students will learn the operation of VoIP protocols and understand the concept about Video over IP.

Learning objectives

On completion of each module the participants will be able to:1 Describe the Voice over IP protocols 1.1 Explain the main VoIP protocols: H.323, Media Gateway Control Protocol (MGCP) –

RFC 2705 and H.248 (MEGACO)1.2 Explain Session Initiation Protocol (SIP) – RFC 3261 1.3 List the Real-Time Transport Protocol (RTP) and Real Time Control Protocol (RTCP) –

RFC 3611 and RFC 35501.4 Perform Theoretical Exercise

2 Describe the Video over IP protocols 2.1 Explain Video over IP2.2 Describe traditional video and IP Multicast2.3 Describe concept of Internet Group Management Protocol IGMP2.4 Describe video formats MPEG and Streaming2.5 Comment Traditional solutions, Video conferencing over IP2.6 Perform theoretical exercises covering SIP messages

Target audience

The target audience for this course is the staff involved in IP networking and require more knowledge on IP networks to guarantee quality of service, security, and management of real-time traffic.

Prerequisites










Learning situation

This course is based on theoretical instructor-led lessons given in classroom environment.

Time schedule



1 • Explain the main VoIP protocols: H.323, Media Gateway Control Protocol (MGCP) and H.248 (MEGACO)

0.5 h

• Explain Session Initiation Protocol (SIP) 1.0. h

• List the Real-Time Transport Protocol (RTP) and Real-Time Control Protocol (RTCP) –RFC 3611 RFC 3550

0.5 h

• Explain Video over IP 0.5 h

• Describe Traditional Video Transport and IP Multicast 0.5 h

• Comment concept of Group Management Protocol - IGMP 0.5 h

• Describe video format MPEG and Streaming 0.5 h

• Describe video on demand vs. video broadcasting 0.5 h

• Comment traditional solutions, video conferencing over IP 0.5 h

• Perform theoretical exercises 1.0 h






IPv6 Networking

LZU 108 7424 R3A

Description

This course gives a profound technical presentation of the Internet protocol IPv6. The course is focused on the protocols and mechanisms defined within IPv6 as well as functions affected by IPv6, such as routing protocols and DNS.

The course gives a clear view of how the Transition Mechanisms function and how they are used to establish IPv6 networks in a world of IPv4 networks and to ensure connectivity between different IPv6 networks and between IPv6 and IPv4 networks. The students will get experience in how to set up an IPv6 network configuring routers and hosts.

Learning objectives


1 Give a technical overview of IPv6 networking1.1 Understand why need IPv61.2 Describe the IPv6 header and platform1.3 Compare IPv4 with IPv61.4 Identify new features1.5 Describe how to increase Address Space 1.6 Describe Main Bodies

2 Describe the IPv6 header and ICMPv62.1 Explain the IPv6 Base Header and Extension Header2.2 Explain how to create IPv6 from IPv42.3 Describe the ICMPv6

3 Describe the IPv6 Addressing3.1 Explain the address architecture3.2 Describe Unicast, Multicast and Anycast addresses3.3 Describe an IPv6 basic configuration in routers and hosts and auto-configuration3.4 Describe Neighbor Discovery

4 Decribe the Upper-Layer Protocols4.1 Describe DNS and DHCP for IPv64.2 Explain Transport Layer protocols4.3 List and explain some applications






5 Describe Mobile IPv65.1 Understand the Building Blocks5.2 Explain Registration and Bindings

6 Describe and configure the Transition Mechanisms between IPv4 and IPv66.1 Connecting IPv6 islands6.2 Configure tunnels6.3 Describe IPv6 to IPv4 (6to4)6.4 Explain ISATAP and Teredo6.5 Explain SIIT NAT-PT6.6 Describe Tunnel Mechanisms6.7 Explain the automatic Tunnels and Tunnel Broker6.8 Describe IPv6 over IPv4 (6over4)6.9 Explain Dual Stack Transition Mechanism

Target audience

The target audience for this course is: Network Design Engineers, Network Deployment Engineers, System Technicians, Service Technicians, System Engineers and Service Engineers.

Prerequisites


IP Networking LZU 102 397 R5A

IP Quality of Service and MPLS LZU 108 7716 R1A

IP Security LZU 108 7717 R1A

Voice and Video over IP LZU 108 7718 R1A



Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using equipment and tools, which are accessed remotely.






Time schedule



1 IPv6 Introduction

IPv6 Header and ICMPv6

IPv6 Addressing

Upper-Layer Protocols

1.5 hours

2.0 hours

1.5 hours

1.0 hour

2 Mobile IPv6

Transition Mechanism

1.0 hour

5.0 hours






IPv6 Quality of Service

LZU 108 7521 R2A

Description

This course is a technical presentation of the feature related to IPv6: Quality of Service (DiffServ, RSVP / IntServ). IPv6 and this feature are essential in new generation networks.

Learning objectives

On completion of this course the participants will be able to: 1 Explain how QoS works1.1 Explain what is quality of service1.2 Explain QoS Mechanisms1.3 IP QoS Major Issues1.4 Describe DiffServ and IntServ (RSVP)1.5 Differentiate between Policing and Metering1.6 Explain Traffic Class and Flow label for IPv61.7 Describe Traffic Conditioning1.8 Explain Scheduler and Shaper1.9 Explain Queue Management (RED/WRED)

Target audience


Prerequisites


IPv6 Networking, LZU 108 7424 R2A








Learning situation


Time schedule



Day Short description of the topics in the course Estimated time1 • Introduction

• Welcome• Presentation• Training Schedule

0,5 h

• Explain How QoS work• Explain what is quality of service• Explain QoS Mechanisms• Describe DiffServ and IntServ (RSVP)• Differentiate between Policing and Metering• Explain Traffic Class and Flow label for IPv6• Describe Traffic Conditioning• Explain Scheduler and Shaper• Explain Queue Management (RED)

5,5 h






IPv6 Routing

LZU 108 7520 R3A

Description

This course is a profound technical presentation of the routing protocols RIPng, OSPFv3, ISIS, and BGP4+. The protocols and their different functions in the Internet will be discussed.

The participants will learn how to configure the advanced features on an IPv6 router.

Learning objectives


1 Explain how the Routing Protocols are used in IPv61.1 List the Routing Protocols used in IPv61.2 Explain how they are working on a router and the hosts of an IPv6 network1.3 Explain static routing and routing protocol

2 Describe how RIPng is working2.1 Explain main RIPng functionalities2.2 Show RIPng Algorithm and its Mechanism2.3 Explain RIPng Advantages and Limitations2.4 Explain RIPng Advanced Features

3 Describe how OSPFv3 works3.1 Describe the OSPFng Header3.2 Explain Link State Advertisements (LSAs)3.3 Explain Link-State Database and Hello packets3.4 Explain Routing Calculations and SPF Algorithm3.5 Explain OSPF Areas3.6 Perform practical exercises covering OSPFv3 protocol

4 Describe how ISIS works4.1 Explain Support on data link layer4.2 Explain Hello packets4.3 Describe Link State packets4.4 Explain Sequence number packets4.5 Describe Options4.6 Explain Level 1 and Level 2 routers4.7 Describe Designated router election4.8 Explain Area reconfiguration4.9 Explain Overload state4.10 Describe the comparison with OSPFv3






5 Describe how BGP4+ is working5.1 Describe BGP Message Types5.2 Explain the BGP Header and Session5.3 List Keep-Alive Features5.4 Explain Internal-External BGP5.5 Understand Best Path Calculation5.6 Describe new BGP attributes5.7 Perform practical exercises covering BGP4+ protocol

Target audience


Prerequisites

Successful completion of the following course:IPv6 Networking LZU 108 7424 R3A



Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using equipment and tools, which are accessed remotely.

Time schedule



1 Routing Protocols 3.0 hours

RIP New Generation 3.0 hours

2 Open Shortest Path First for IPv6 - OPFv3 6.0 hours

3 IS-IS for IPv6 1.5 hours

Border Gateway Protocol for IPv6 - BGP4+ 4.5 hours






IPv6 Security

LZU 108 7522 R2A

Description

This course is also a profound technical presentation of the advanced feature related to IPv6: IPSec. IPv6 and this feature are essential in new generation networks.

Learning objectives

On completion of this course the participants will be able to: 2 Describe how IPv6 Security (IPsec) is working2.1 Describe Security Threats2.2 Explain Basic Security Concepts and Security Associations2.3 Describe Crypto Primitives2.4 Explain Authentication Header (AH)2.5 Explain Encapsulating Security Payload (ESP)2.6 Explain Internet Key Exchange (IKEv2)

Target audience


Prerequisites


IPv6 Networking, LZU 108 7424 R2A








Learning situation


Time schedule


Day Topics in the course Estimated time1 • Introduction

• Welcome• Presentation• Training Schedule

0,5 h

• IPSec• Security Threats • Basic Security Concepts• Security Associations • Crypto Primitives• Authentication Header (AH)• Encapsulating Security Payload (ESP)• Internet Key Exchange (IKEv2)• Perform exercises covering these mechanisms and

features

5,5 h






CPP Node Features and Functions

LZU 108 6116 R9A

Description

Ericsson’s WCDMA Radio Access Network (RAN) nodes, namely the RNC, RBS and RXI- and the Mobile Media Gateway (M-MGw) are based on Connectivity Packet Platform (CPP). This course is designed to get an overview of the CPP, the functions of CPP-based nodes, as well as relating the functionality of each CPP node to the boards in that node.

Learning objectives


1 List the Connectivity Packet Platform nodes in the GSM and WCDMA network1.1 List the data rates supported by the main mobile access technologies1.2 Explain on an overview level the function of the following WCDMA CPP nodes: M-

MGw, RNC, RBS and RXI1.3 Explain the difference between IP/Ethernet and ATM as transport options in the

WCDMA RAN1.4 List the main interfaces in the WCDMA RAN where IP/Ethernet can be used as an

alternative to ATM

2 Understand the major concepts related to the Connectivity Packet Platform2.1 Explain on an overview level the Connectivity Packet Platform (CPP) hardware 2.2 Explain the processor hierarchy in a CPP node2.3 List the function, features and capacity of the General purpose Processor Board

(GPB)2.4 List the function, features and capacity of the Switch Core Board (SCB) and Switch

Extension Board (SXB) and the CMX Board 2.5 List the function, features and capacity of the ET-MC1, ET-M3, ET-M4, ET-MF4, ET-

MC41, ET-MF41, ET-MFG, ET-MFX and ET-IPG Boards2.6 List the function, features and capacity of the Timing Unit Board

3 Explain on overview level the features and functions of the M-MGw3.1 List the M-MGw roles3.2 List the M-MGw specific boards3.3 List and explain at an overview level the Media Stream Functions in the M-MGw 3.4 Explain on an overview level the M-MGw Modules and hardware configurations

4 Explain on overview level the features and functions of a WCDMA-RNC4.1 Explain the role of the RNC in the Core Network connectivity4.2 Explain the role of the RNC in mobility scenarios4.3 List the RNC Specific boards4.4 Explain the concept of the RNC Module4.5 Explain the RNC hardware configuration for both RNC3810 and RNC3820






5 Explain on overview level the features and functions of a WCDMA-RBS5.1 Explain the power control features in the RBS5.2 Explain on overview level the High Speed Packet Access (HSPA) features5.3 List the RBS 3000 WCDMA Product family5.4 List the RBS 3000 Specific hardware5.5 List the RBS 6000 Product family5.6 List the RBS 6000 Specific hardware for WCDMA

6 Explain on overview level the features and functions of the RXI6.1 List the RXI Product Family6.2 List the transport network topologies where the RXI can be used6.3 List and explain the ATM-services provided by RXI6.4 Explain the hardware architecture of the RXI 820 and RXI 860

Target audience The target audience for this course is: Field Technician, Service Engineer, and System Engineer Since this course is an overview of all the CPP based nodes, it is also suitable for anyone wishing to get an overview of these products.

Prerequisites


Ericsson WCDMA System Overview LZU 108 5418



Learning situation

This course is based on theoretical instructor-led lessons and theoretical exercises given in a classroom environment.






Time schedule



1 3G Network Introduction

Connectivity Packet Platform

M-MGw Features and Functions

RNC Features and Functions

RBS 3000 and RBS 6000 Features and Functions

RXI Features and Functions

1 hour

1.5 hours

1 hour

1 hour

1 hour

0.5 hour






TFO/TrFO Interworking Introduction

LZU 108 6596 R2A

Description

This course provides the competence to ensure that the features “Tandem Free Operation” and “Transcoder Free Operation” will be deployed for optimal use of their benefits, like excellent speech quality, cost savings in transmission capacity, cost saving in transcoder equipment or Network Transparency for wideband speech services. Network Planning aspect and configuration are discussed as statistics on the network functionality.

Learning objectives

On completion of this course the participants will be able to:1 Explain the concept of TFO and TrFO and their inter-working1.1 Detail basic traffic cases for TFO (mainly for GERAN)1.2 Detail basic traffic cases for TrFO, (mainly for UTRAN)1.3 Explain the benefits of TFO/TrFO Inter-working1.4 Details to be considered:

- The Ericsson implementation of Codec Negotiation: the Concept of “direct” and “indirect” Codecs, the Codec Selection rules, the DCODEC concept- Inter-working of Non-Layered and Layered Networks- Compressed speech between MGWs without TFO in BSS- Data and Fax calls

2 Configure TFO and TrFO in the Core Network2.1 Configure TFO/TrFO in the MSC-Server2.2 Configure TFO/TrFO in the M-MGw3 Explain how to verify and monitor the benefits of TFO/TrFO Interworking in the

network4 Examples of TFO and TrFO and their Inter-working in different network

scenarios

Target audience


System Engineers

Network Design Engineers

Network Deployment Engineers






Prerequisites

Participants shall have extensive working experience in the areas of Core Network Design, Configuration Management or Performance Management.



Learning situation


Time schedule

The time required always depends on the knowledge of the attending participants and the hours stated below should be used as an estimate.

Day Topics in the course Estimated time1 • Course Introduction and Initial test 0.5 h

• Concept of TFO / TrFO 2 h• Configuration of TFO / TrFO in core network 1,5 h• Monitoring benefits with TFO/TrFO• Examples of TFO, TrFO in different network scenarios

0.5 h1 h

• Test and conclusion 0,5 h






APG43 Delta

LZU 108 6867 R3A

Description

The Adjunct Processor Group 43 (APG43) is the IO system of the APZ control system in AXE 10 and AXE 810 with focus on board size footprint and integration in the evolved Generic Ericsson Magazine (EGEM). The APG 43 is housed on blades (eGEM boards) in EGEM magazine, utilizing the EGEM infrastructure.

This course will cover aspects in the new APG release. The students will retain knowledge regarding the architecture and the functionality of the APG43. The differences to the previous APGs will be covered.

Learning objectives

At the end of this course, the students will be able to:

1 Describe the APG features on an overview level1.1 Be introduced to the main components of the APG 431.2 Describe the APZ versions used with APG 431.3 Observe the capacity differences between different IO systems

2 Describe the APG Hardware2.1 Describe the layout of the EGEM/EGEM2 subrack housing the APG 432.2 Explain the Ethernet star connections in the backplane2.3 Describe the different boards used in APG 432.4 Describe the front cabling connections in APG 43

3 Describe the APG Software3.1 Describe the new software structure used in APG433.2 Describe the new sub-systems introduced in APG 433.3 Explain the VERITAS software RAID function in APG 433.4 Describe the quota based protection feature

4 Discuss other improvements in APG 434.1 Understand the new Configuration and Hardening feature in APOS4.2 Describe the different user interfaces towards the APG 434.3 Explain the changes to the Disaster Recovery procedure in APG 434.4 Briefly describe the procedure to change a GED disk board4.5 Describe the command differences between APG40 and APG43






Target audience

The primary target audience for this course: System Technicians and other staff working with APG43.

Prerequisites

The participants should be familiar with the previous APG40 releases.



Learning situation

This course is based on theoretical instructor-led lessons.

Time schedule


Day Topics in the course Estimated time1 • Introduction 1 h

• APG 43 Hardware and Interfaces 2 h

• APG 43 Sofware and 3rd party midlleware 1 h

• Other Improvements 2 h






APG43 Operation and Maintenance

LZU 108 7177 R2A

Description

Do you want to know how the APG43 works? Are you required to perform Operation and Maintenance activities on the APG43 such as backups, creating new user accounts, or configuring statistical measurement programs?

This course describes the hardware and software structure of the APG43. It also explains many of the features in APG43 while describing the procedures and commands used to configure them.

The participants will gain experience in handling the APG43 by performing a series of practical exercises designed to re-enforce the theoretical components of the course. The exercises include fault handling, trouble report creation, file transfer definitions, backup procedures and more.

Learning objectives


1 Describe the APG43 features on an overview level1.1 Introduce the APG43 product and its main features1.2 Compare the performance and hardware characteristics of APG43 to previous IO

systems1.3 Explain APG43 in a BC System

2 Describe the APG43 hardware components2.1 Explain the layout of the eGEM/eGEM2 magazine including APG432.2 Describe each board which makes up the APG43 and APG43/2 and their functions2.3 Understand the front cabling used in APG43, and be familiar with the connections2.4 Be familiar with the APG43 data disk directory structure, and describe the contents

3 Use different interfaces to connect to the APG43 platform3.1 Connect to the APG43 using Telnet, WinFiol or Terminal Server3.2 Describe the serial console port in APG43, and when it is used3.3 Describe how to connect in a single CP or multiple CP

4 Explain the APG43 software structure4.1 Provide a basic understanding of the software architecture, and describe the major

components APHW, APOS, ACS on an overview level4.2 Describe some of the commonly used applications such as Microsoft Cluster Server

and other 3rd Party products4.3 Describe the functions of ACS and AES subsystems used in APG43 4.4 Perform exercises to define file transfer destinations in the AP, and generate files to

observe the file transfer process.

5 Describe the principles of the alarm system in APG435.1 Explain the principles of the alarm system on the APG43






5.2 Describe the functions of PRC, USA and SSU

6 Describe the File Management System implemented in APG436.1 Understand the main file handling functions used in FMS6.2 Perform exercises to create, rename, copy and remove files in FMS6.3 Explain the CP backup functions supported in APG436.4 Understand how to transfer a CP backup file into the AP to be loaded into the CP

7 Describe the Man-Machine Subsystem in APG437.1 Describe the hardware components in MCS7.2 Understand how users can be defined in APG43 with different levels of access to AP

and CP functions7.3 Explain the alarm display function used in APG437.4 Define the data for an external alarm in APG437.5 Explain License Management7.6 Describe Command Authority Profile7.7 Explain Function Definition Distribution7.8 Describe Cluster Operation Mode and Session Types

8 Describe the APG43 System Backup, Restore and Function Change procedures8.1 Describe the principles of the APG43 backup function, and perform a backup of the

APG438.2 Explain the APG43 system restore procedure, and perform a single Node restore8.3 Describe the Function change principles, and perform a soft function change in

APG43

9 Describe the principles of the Statistics and Traffic Measurement subsystem STS in APG43

9.1 Have a basic understanding of STS concepts and their implementation in APG439.2 Explain the counters, objects and object types used in STS9.3 Understand the output of files and the different formats used in STS9.4 Perform and exercise to define measurement reports to produce statistical data to be

output to a destination defined in APG43






Target audience The target audience for this course is: System Technicians, System Engineers.

This audience is responsible for Network Maintenance, Network Operation and System administration

Prerequisites

The participants should be familiar with previous version of APG 40 systems.


APG43 Delta FAB 102 2130 R1A



Learning situation

This course is based on theoretical and practical instructor-led lessons given in both a classroom and in a technical environment, using equipment and tools.






Time schedule



1 APG43 Introduction 1 hour

APG43 Hardware 2 hours

Accessing the APG43 Network 2 hours

APG43 Software 1 hour

2 APG43 Software 2 hours

APG43 Alarm System 2 hours

APG43 File Management Subsystem 2 hours

3 APG43 File Management Subsystem 2 hours

APG43 Man-Machine Communication Subsystem 2 hours

APG43 Backup 2 hours

4 APG43 Restore and Function Change 4 hours

APG43 STS 2 hours






APG43 Recovery Procedures

LZU 108 7179 R2A

Description

Do you want to know how to recover the APG43 when it is not working normally? Do you how to reconnect the APG43 in the network? This course will bring you all these answers by engaging in theoretical and practical sessions with the trainer, you will have the opportunity to explore the APG43 functionalities with recovery procedures.

After attending this course the students will know how to make a proper backup of the APG43 system to different media and to be able to use the different backups to recover the APG43 in a fast and correct manner.

Learning objectives


1 List the recovery procedures available on APG431.1 Describe the difference between CSRs and TRs1.2 Explain how to create a trouble report1.3 List the information that needs to be included

2 Describe the need for a backup2.1 Describe how to create a proper backup2.2 Describe in which way backups can be transferred

3 Describe how to make a single node restore of the APG433.1 Describe how to make a two-node restore of the APG43

4 List the prerequisites for performing Disaster Recovery on an APG434.1 Describe the basics and perform the relevant OPI: AP, System Disaster Recovery.

5 Recognize when a Quorum Restore must be performed:5.1 Describe how to perform the Quorum Restore

6 Recognize when a Data Disk Restore must be made6.1 Describe how the Data Disk Restore is performed

7 List other restore methods that exist7.1 Explain a hardware replacement procedure in APG43






Target audience

The target audience for this course is: Network Deployment Engineers, System Technicians, Service Technicians, System Engineers, Service Engineers, Field Technicians and System Administrators.

These audiences can also include all staff working both for Ericsson and for external companies with maintenance and support of APG43 systems.

Prerequisites

The participants should be familiar with the previous APG40 releases.

Successful completion of the following training flow:• APG43 Delta FAB 102 2130 R1A

• APG43 Node Operation & Configuration FAB 102 2249 R1A



Learning situation







Time schedule



1 Different recovery methods 1 h

Trouble Reports 0,5 h

The backup procedures 0,5 h

2 Recovery procedures: Restore 1 h

Recovery procedures: Disaster Recovery 0,5 h

Recovery procedures: Quorum Log Restore 0,5 h

3 Recovery Procedures: Data Disk Recovery 0,5 h

Recovery Procedures: Node Change 0,5 h

Other methods 0,5 h

Course Termination 0,5 h






APG43 Installation and Configuration

LZU 108 7178 R2A

DescriptionThis course will prepare participants for installation and configurational tasks on the APG43 by engaging in theoretical and practical sessions with the trainer.

The participants will have the opportunity to explore the APG43 functionality during installation and configuration procedures. It is assumed that the APG43 has been started up and configured in the factory as a standalone APG and delivered to site with initial configuration data. Based on this the students will be able to configure the customer dependent site parameters and check and reconfigure any other parameters as may be required. The students will also perform operational tasks to test IO applications and the connection and communication of the APG43 with the APZ.

After the course the students will be able to install, configure and put an APG43 into operation.

Learning objectives


1 Describe the subsystem structure of the APG43 and the hardware layout in the EGEM/EGEM2

1.1 Describe the main hardware and functionality changes from the APG40/APG431.2 Explain APG43 in Blade Cluster1.3 Describe the subsystems in the APG431.4 Recognize the hardware configuration of the APG431.5 Explain the main hardware and functionality differences from the APG401.6 Describe the structure of the Data Disk in APG43

2 Describe the APG43 hardware and cable connections2.1 Make and verify an AP System backup 2.2 Explain Hardware Configuration (HWC) changes2.3 Prepare for Site Parameter Change2.4 Perform a Start Up and Test procedure on an APG432.5 Configure the APG43 for APZ 2.6 Perform Test of APG43

3 Explain user management in APG433.1 How to define different users, groups and their Authorities in APG43 and CP3.2 Describe Command Authority Profile3.3 Explain APG43 Domain handling3.4 Describe Master User Domain (MUD)3.5 Explain License Management

4 Describe the eTrust Antivirus software






4.1 Know how to avoid getting virus on the APG43 4.2 Configure the antivirus software 4.3 Explain the virus definitions4.4 Create a scheduled scan job

Target audience

The target audience for this course is: System Technicians, System Engineers.

These audiences are personnel working with Network Maintenance, Network Operation, Network Development and System Administration.

Prerequisites

The participants should be familiar with Windows 2003 and have fulfillled the course:

APG43 Operation and Maintenance, LZU 108 7177

And

APG43 Delta, LZU 1086867

Paricipants should also have some AXE knowledge equal to the following course:

AXE Survey, LZU 108775


The length of the course is 12 hours and the maximum number of participants is 8The number of participants should only be 8 for practical courses and 16 for theory courses.

Learning situation

This course is based on theoretical and practical instructor-led lessons given in both classroom and in a technical environment using equipment and tools, which are accessed both locally and remotely.

Time schedule








1 Course Introduction 1 hours

1 Chapter 1 - Introduction to APG43 1 hours

1 Chapter 2 - Start Up, Configuration and Test of APG43 2 hours

1 Exercises for Chapter 1 and 2 2 hours

2 Chapter 3 - Authority System and User Account Management 2 hours

2 Chapter 4 - Antivirus Configuration 1 hour

2 Exercises for Chapter 3 and 4 3 hours






Date post:	27-Jan-2016
Category:	Documents
Upload:	harsh-pathak
View:	240 times
Download:	4 times

Mobile Soft Switch Solution in BC

Documents