For Release QS 1.0x
Page N 1 / 22 24/08/07 Mocassin
Create a 3D Mocassin
How to create a Mocassin in 3D using the specific Macro for QS
A- Install the Program
Double click on the 'Mocassin V1.2.exe' file
Select 'English' then Click 'NEXT'
Here you have to input the hard disk reference where to
install files
Click 'NEXT'
For Release QS 1.0x
Page N 2 / 22 24/08/07 Mocassin
Basicly the hard disk must be the hard disk where you have installed
Shoemaster program
For example if you have installed Shoemaster on hard disk C:\,
you must specify C:\
For example if you have installed Shoemaster on hard disk D:\,
you must specify D:\
Select New Install then click 'Install'
Select 'Finish'
And add in your 3D Startup File the syntax
$n//mocassin/setup.ini
For Release QS 1.0x
Page N 3 / 22 24/08/07 Mocassin
B- Create the Mocassin Model
Please note that the macro
Has been checked with a Right Last
For Release QS 1.0x
Page N 4 / 22 24/08/07 Mocassin
A- Create the inner reference line
B- Create the outer reference line
C- Create the bottom reference line
Using the bottom surface
For Release QS 1.0x
Page N 5 / 22 24/08/07 Mocassin
D- Create the Apron Pivoted Piece
For Release QS 1.0x
Page N 6 / 22 24/08/07 Mocassin
C- Use the Mocassin Macro
Go to the menu Mocassin and select the option Open
You will get the following toolbar
For Release QS 1.0x
Page N 7 / 22 24/08/07 Mocassin
;
Step 1- Set the mocassin
Select the Icon Setup Mocassin and follow the instructions below
Select the Outer Upper Reference
For Release QS 1.0x
Page N 8 / 22 24/08/07 Mocassin
Select the Inner Upper Reference
For Release QS 1.0x
Page N 9 / 22 24/08/07 Mocassin
Select the sprung piece
For Release QS 1.0x
Page N 10 / 22 24/08/07 Mocassin
Step 2- Move the Inner Part
Select the Icon Move Inner
For Release QS 1.0x
Page N 11 / 22 24/08/07 Mocassin
Step 3- Rotate the Inner Part
Select the Icon Rotate Inner
For Release QS 1.0x
Page N 12 / 22 24/08/07 Mocassin
Step 4: Move the Outer Part
Select the Icon Move Outer
For Release QS 1.0x
Page N 13 / 22 24/08/07 Mocassin
Step 5- Rotate the Outer Part
Select the Icon Rotate Outer
For Release QS 1.0x
Page N 14 / 22 24/08/07 Mocassin
Step 6- Split Mocassin
Select the Icon Split Mocassin
And Follow the order selection below
For Release QS 1.0x
Page N 15 / 22 24/08/07 Mocassin
For Release QS 1.0x
Page N 16 / 22 24/08/07 Mocassin
For Release QS 1.0x
Page N 17 / 22 24/08/07 Mocassin
Step 7- Reverse Line
Select the Icon Reverse Line
The Line Direction must be like the first image below, if not select all line to reverse
For Release QS 1.0x
Page N 18 / 22 24/08/07 Mocassin
Step 8- Blend the Inner Part
Select the Icon Blend Inner
Select the following sequence
For Release QS 1.0x
Page N 19 / 22 24/08/07 Mocassin
For Release QS 1.0x
Page N 20 / 22 24/08/07 Mocassin
Step 9- Blend the Outer Part
Select the Icon Blend Outer
Select the following sequence
For Release QS 1.0x
Page N 21 / 22 24/08/07 Mocassin
For Release QS 1.0x
Page N 22 / 22 24/08/07 Mocassin
Step 10- Finish Mocassin
Select the Icon Finish Mocassin
This command merges the mocassin line, you are ready to delete nodes on the line