Product Data Sheet 00813-0100-4360 Pressure-173 Model 1151 Model 1151 Alphaline ® Pressure Transmitters . Model 1151 PROVEN ROSEMOUNT ® VALUE AND PERFORMANCE • Versatile application: Ranges from 0–0.5 inH 2 0 to 6,000 psig (1.24 kPa to 41370 kPa) • Easy maintainance and upgradeability with solid-state, plug-in circuit boards; adjustable damping; and local span and zero adjustments • Compact, rugged, construction for easy installation and long-lasting performance • Smart, analog, or low-power electronics to fit almost every application • Over 30 years of proven Rosemount quality and technology
Transcript
Product Data Sheet 00813-0100-4360
Model 1151 Alphaline® Pressure Transmitters.
Model 1151
Pressure-173
Mod
el11
51
PROVEN ROSEMOUNT®
VALUE AND PERFORMANCE• Versatile application: Ranges from 0–0.5
inH20 to 6,000 psig (1.24 kPa to 41370 kPa)
• Easy maintainance and upgradeability withsolid-state, plug-in circuit boards; adjustabledamping; and local span and zeroadjustments
• Compact, rugged, construction for easyinstallation and long-lasting performance
• Smart, analog, or low-power electronics to fitalmost every application
• Over 30 years of proven Rosemount qualityand technology
Model 1151 Alphaline ® Pressure Transmitters
Model1151
Pressu
INTRODUCTIONThis product data sheet highlights Rosemount® Model 1151 differential, absolute, gage, and high-line pressure transmitter features and options. For information about the draft range, liquid level transmitters, transmitters with remote seals, and additional information on smart transmitters, refer to their respective data sheets referenced on the back page of this data sheet.
INDUSTRY-LEADING PERFORMANCEAND FEATURESThe Model 1151 Alphaline® series of pressure transmitters brings true precision to the measurement of flow, level, gage and absolute pressures, vacuum, and specific gravity. Direct electronic sensing with the completely sealed δ-cell (delta-cell) capacitance sensing element allows significant improvement and stability in pressure measurements. Welded stress isolation clamping in the sensor housing prevents introduction of errors caused by stresses and torques on the process flanges and minimizes effects of line pressure and overpressure.
Installation, calibration, and commissioning are simplified by compact design, integral junction box, and local span and zero adjustments.
The housing features an explosion-proof, weather-proof construction with separate compartments for the electronics and wiring connections. For most models, 316L SST, Hastelloy® C, Monel®, gold-plated Monel, or tantalum materials are available for corrosive service. Modular construction and plug-in printed circuit boards aid in trouble-shooting and reduce parts stocking
APPLICATIONSModel 1151 Pressure Transmitters are available in a variety of configurations for differential, flow, gage, absolute, vacuum, liquid level, and specific gravity measurement applications. The transmitter model number, determined from the ordering information tables, specifies available features such as pressure ranges, outputs, and materials of construction that are basic to each transmitter. Additional options, such as accessories, certifications, and special manufacturing procedures are also available.
OPERATIONDuring operation, the isolating diaphragms and fill fluid on the high and low sides transmit the process pressure to the oil fill fluid. The fluid in turn transmits the process pressure to a sensing dia-phragm in the center of the d-cell sensor. The sensing diaphragm functions as a stretched spring element that deflects in response to differential pressure across it (in GP transmitters, atmospheric pressure is transmitted in a like manner to the low side of the sensing diaphragm). In AP transmitters, a reference pressure is maintained on the low side. The displacement of the sensing diaphragm, a maximum movement of 0.004 in. (0.10 mm), is proportional to the pressure. Capacitor plates on both sides detect the position of the sensing diaphragm. The differential capacitance between the sensing diaphragm and the capacitor plates is converted electronically to an appropriate current, voltage, or digital HART® (Highway Addressable Remote Transducer) output signal.
Capacitor Plates
Lead Wires
Sensing Diaphragm
Rigid Insulation
Oil Fill
IsolatingDiaphragm Welded Seals
1151
–01
42A
FIGURE 1. Cross Section of the Rosemount d-Cell™ Sensor.
Operating temperature limit: –40 to 150 °F(–40 to 65 °C).
Meters are enclosed in a housing certified by Factory Mutual as explosion proof for Class I, Division 1, Groups B, C, and D; Class II, Division 1, Groups E, F, and G and Class III, Division 1.
For optional CSA explosion-proof approval, see certification Option Code E6.
M1 Linear Analog Meter, 0–100% ScaleM2 Square Root Analog Meter,
0–100% Flow ScaleM3 Special Scaling Analog Meter
(Specify Range)M6 Square Root Analog Meter, 0–10 √ Scale
NOTESMeter Options are not available with Output Codes L or M,or Option Codes V2 or V3.
Meter Options M2, M6, M8, and M9 are not available withOutput Code J.
Meter Options M4, M7, and M9 are not available withOutput Code G.
re-178
LCD4-digit display.
Indication accuracy ±0.25% of calibrated span±1 digit.
Display resolution at ±0.5% of calibrated span±1 digit.
Operating temperature limit: –4 to 158 °F(–20 to 70 °C).Plug-in mounting configuration.
Meters are enclosed in a housing certified by Factory Mutual as explosion proof for Class I, Division 1, Groups B, C, and D; Class II, Division 1, Groups E, F, and G and Class III, Division 1.
For Optional CSA explosion-proof approval, see certification Option Code E6.
M4 Linear LCD Meter, 0 to 100%M7 Special Scale LCD Meter (Specify Range,
Mode, and Engineering Units)M8 Square Root LCD Meter, 0 to 100%M9 Square Root LCD Meter, 0–10 √ Scale
751-
015
3A,
1151
-253
4A
01A
,11
51I0
5A
7.5 Max. (191)Optional Meter
0.75 (19)Clearance forCover Removal(Typical)
9.0 Max.(229)
OPTION CODE M4LINEAR SCALE
OPTION CODE M1LINEAR SCALE
NOTEDImensions are in inches (millimeters).
FIGURE 6. Meter Options.
Rosemount Inc.
Mod
el11
51
115
1-11
51D
17A
Process ConnectionsD1 Side Drain/Vent-Top
Drain/vent valve mounted in side of flange.
Top position used to vent gas buildup in liquid process applications with transmitter mounted vertically.
Plug of same material as requested flange inserted in end of flange opposite adapter.
D2 Side Drai n/Vent-B ottomDrain/vent valve mounted in side of flange.
Bottom position used to drain liquid buildup in gas process applications with transmitter mounted vertically.
Plug of same material as requested flange inserted in end of flange opposite adapter.
D3 1/4–18 NPT Process ConnectionOption provides 1/4–18 NPT process connection on flanges rather than standard 1/2–14 NPT.
Flange adapters are deleted to provide desired connection.
D6 316 SST Low Side Flange(Model s 1151GP and 1151AP Only)
½–14 NPTConnection
on Adapters(¼–18 NPT
Connectionwit h Adapters
Removed)
Standard Drain/VentReplaced with Plug
Alternate SideDrain/Vent Top Posit ion
(Opti on Code D1)
Alt ernate Side Drain/Vent BottomPosi t ion (Opti on Code D1)
FIGURE 7. Model 1151 Process Connections.
1151
-115
1B04
A
K1 1/4–18 NPT Kynar™ Process Flange InsertK2 1/2–14 NPT Kynar Process Flang e Insert
Options provide Kynar plastic process flange insert that prevents process from coming in contact with the metal of the flange. One process insert for Models 1151AP, GP and LT; two inserts for Model 1151DP.
Process connections are from the side.
Available with carbon steel and stainless steel process flanges only.Pressure Maximum: 200 psi at 200 °F with Kynar impulse piping; 300 psi at 200 °F with metal impulse piping.
S1 Ass embled with One Remote Diaphragm SealS2 Ass embled with Two Remote Diaphragm
SealsOptions provide for the assembly of one or two remote diaphragm seals.
For Models 1151AP and 1151LT applications consult factory.For seal choices, see Rosemount Product Data Sheet 00813-0100-4016.
KynarInsert ¼–18 or ½–14 NPT
Process Connection
FIGURE 8. Flange Insert.
Pressure-179
Model 1151 Alphaline ® Pressure Transmitters
Model1151
Pressu
1151
-115
1B17
B11
51-1
151B
17B
S4 Assembled with Model 1195 Integral OrificeDesigned for highly accurate, small-bore flow measurement of any clean gas, liquid, or vapor. See Product Data Sheet 00813-0100-4686.Reduce the costs associated with traditional orifice plate installations.
Several configurations are available factory assembled to Rosemount differential pressure transmitters.(1)
Wide orifice bore/flow range capability.
Wide choice of process connections, including threaded, socket weld, and ANSI flanges.
Static pressure maximum limit is 3,000 psig.
Wetted materials are available that comply with NACE MR 01-75(90).
Available only with Ranges 2, 3, 4, and 5.
For integral orifice selection, see Product Data Sheet 00813-0100-4686.
OPTIONAL3-VALVE MANIFOLD
MODEL 1195 INTEGRALORIFICE ASSEMBLY
FIGURE 9. Model 1151 with Manifold and Model1195 Integral Orifice.
re-180
115
1-11
51A
21A
Wetted O-rings
Standard: Viton ® (2)
W2 Buna NW3 Ethylene-PropyleneW4 Aflas ®
W5 Copper O-ring for Vacuum Service(Nonwetted - Model 1151LT only)
W6 Spring-Loaded Teflon ®
Contains a Hastelloy spring that is in contact with the process fluid. Consult factory if Hastelloy is unacceptable.
ProceduresStandard Configuration
Unless otherwise specified, transmitter will be shipped as follows:
Engineering Units: inH2O4 mA: 020 mA: Upper Range LimitOutput: LinearSoftware Tag: BlankCustomer may specify the above items at no charge. Software tag (8 characters) is left blank unless specified.
WettedO-rings
FIGURE 10. Flange Exploded View.
Wetted O-rings
Standard: Viton ® (2)
W2 Buna NW3 Ethylene-PropyleneW4 Aflas ®
W5 Copper O-ring for Vacuum Service(Nonwetted - Model 1151LT only)
W6 Spring-Loaded Teflon ®
Contains a Hastelloy spring that is in contact with the process fluid. Consult factory if Hastelloy is unacceptable.
ProceduresStandard Configuration
Unless otherwise specified, transmitter will be shipped as follows:
Engineering Units: inH2O4 mA: 020 mA: Upper Range LimitOutput: LinearSoftware Tag: BlankCustomer may specify the above items at no charge. Software tag (8 characters) is left blank unless specified.
WettedO-rings
FIGURE 1. Flange Exploded View.
(1) Applicable only to orifice assemblies without piping.(2) For enhanced sealing performance below 0 °F, consult factory.
Rosemount Inc.
Mod
el11
51
C9 Custom Configuration (Option Code C9)If Option Code C9 is ordered, the customer may specify the following data in addition to the standard configuration parameters. Refer to Configuration Data Sheet 00806-0100-4593.
Descriptor: 16 charactersMessage: 32 charactersDate: Day, Month, YearDamping: SecondsBurst Mode: Select Output ChoiceFlange Material: Model Code InformationO-Ring Material: Model Code InformationIsolator Material: Model Code InformationSensor Fluid: Model Code InformationDrain/Vent: Model Code InformationIntegral Meter: Installed or NoneRemote Seal: Specified InformationFailure Mode: High or LowTransmitter Security: Off or On
P1 Hydrostatic TestingEach transmitter is hydrostatic tested according to Table 1.
Test medium is water.
This option provided for transmitters with remote diaphragm seal on application only.
Rosemount Procedure 1746 outlines the testing procedure.
TABLE 1. Hydrostatic Test Pressure.
Model Test Pressure
1151DP 3,000 psi
1151HP 6,750 psi
1151AP 2,000 psi
1151GP
Ranges 3–8 2,000 psi
Range 9 4,500 psi
Range 0 7,500 psi
1151LT
Class 150 Flange 450 psi
Class 300 Flange 1,100 psi
1151DR 1,500 psi
P2 Cleaning for Special ServiceThis option minimizes contaminants to the process system by cleaning wetted surfaces with a suitable detergent.
Rosemount Procedure 97412 outlines the cleaning procedure.
P3 Cleaning for <1 PPM Chlorine/FluorineP4 Calibration at Line Pressure
This option allows transmitters to be calibrated at an elevated line pressure rather than atmospheric pressure.Customer must specify line pressure at which transmitter is to be calibrated.
Customer is provided with calibration data at line pressure and equivalent data at atmospheric pressure.
Available with Models 1151DP and 1151HP only. (Not available with Remote Seals.)
Elevated line pressure and differential span desired for calibration must not exceed the rated pressure for that model of transmitter.
Minimum differential span that can be calibrated at elevated line pressure is 30 inH2O; maximum is 300 psi.
Rosemount Procedure 3787 outlines the calibration procedure.
P5 Calibration at TemperatureThis option allows transmitters to be calibrated at temperatures other than room temperature in the range of 0 to 200 °F (–18 to 93 °C).
Customer must specify temperature at which transmitter is to be calibrated and calibration range.
Calibration temperature will be printed on instrument tag specified by customer, or on a tag wired to the transmitter if no tag is specified.
Rosemount Procedure 27823B outlines the calibration procedure.
Pressure-181
Model 1151 Alphaline ® Pressure Transmitters
Model1151
Pressu
P7 Enhanced Temperature Performancefor Analog ElectronicsTransmitter is specifically compensated as a complete assembly and will exhibit 1/2 of the standard temperature coefficient over the ambient temperature range of 20 to 140 °F (–7 to 60 °C). Outside this range, the unit will meet the standard temperature effect specification published for that model.
Not available on Range 10, limited to 1,500 psi on Range 9.
The transmitter is compensated as an assembly; therefore, units in which the sensor module or electronics are changed after the P7 procedure has been performed will meet the standard published temperature specification for that particular model.
Available on DP, GP, and HP models, Ranges3–8, with SST diaphragms and Output Codes E, G, L, and M.
P8 0.1% Accuracy for Analog ElectronicsAvailable on Model 1151DP (Ranges 3–8), GP (Ranges 3–8), HP, and LT transmitters with 316 SST diaphragms and Output Codes E, G, L, and M.
re-182
OutputsV1 Reverse Output
This option permits reversing of pressure input so that electrical output will increase as pressure input decreases.
This option applies only to Models 1151GP and 1151LT. When this option is selected, the process flange, adapter, drain/vent valve, appropriate O-rings, and bolting are installed on low side of transmitter. Not available for Ranges 9 and 0.
Not available with Model 1151AP. Reverse output on Models 1151DP, 1151HP, and 1151DR can be obtained by connecting high-pressure input to low side of transmitter and vice versa.
This option should not be ordered with smart transmitters (Output Code S). The Model 1151 Smart transmitter can be configured for reverse output through a HART-Compatible Interface.
V2 1 V Test ResistorA 1 V precision resistor is mounted across the test terminals to provide 4–20 mV output or a 10–50 mV output if 10–50 mA output is used.
This option cannot be used with any meter options or Option Codes I5 or I6.
V3 5 V Test ResistorA 5 V precision resistor is mounted across test terminals to provide 20–100 mV output or a50–250 mV output if 10–50 mA output is used.
This option cannot be used with any meter options or Option Codes I5 or I6.
Z1 4-Wire, 0–20 mA OutputZ2 4-Wire, 0–16 mA OutputZ3 4-Wire, 0–10 mA Output
These options provide a zero-based current output.
These options cannot be used with any meter or certification options, Vx options, or Output Codes G, L, M, or S.
Rosemount Inc.
Pressure-183
Mod
el11
51
SPECIFICATIONS
Functional SpecificationsServiceLiquid, gas, and vapor applications.
RangesSee Table 3 for ranges. Minimum span equals the upper range limit (URL) divided by rangedown. Rangedown varies with the output code. See Table 2.
OutputsCode S, Smart4–20 mA dc, user selectable for linear or square root output. Digital process variable superimposed on 4–20 mA signal, available to any host that conforms to the HART protocol.
Code E, Analog4–20 mA dc, linear with process pressure.
Code G, Analog10–50 mA dc, linear with process pressure.
Code J, Analog4–20 mA dc, square root of differential input pressure between 4 and 100% of input. Linear with differential input pressure between 0 and 4% of input.
Code L, Low Power0.8 to 3.2 V dc, linear with process pressure.
Code M, Low Power1 to 5 V dc, linear with process pressure.
Power SupplyExternal power supply required. Transmitter operates according to the following requirements:
Output Codes S, E, J 12 to 45 V dc with no load.Output Code G 30 to 85 V dc with no load.Output Code L 5 to 12 V dc.Output Code M 8 to 14 V dc.
Where:
Code Vmin Vmax Rmin Rmax RL at Supply Voltage (V S)
S(1)
(1) A minimum of 250 ohms is required for communication.
12 45 0 1650 RL = 43.5 (VS – 12)
E(2),J
(2) For CSA approvals Vmax = 42.4 V dc.
12 45 0 1650 RL = 50 (VS – 12)
G 30 85 0 1100 RL= 20 (VS – 30)
L 5 12 Low Power Minimum Load Impedance:100 kVM 8 14
Rmax
RL
Rmin
Vmin VS Vmax0
OperatingRegion
Current Consumption Under Normal OperatingConditions (Low Power Only)
Output Code L1.5 mA dc.
Output Code M2.0 mA dc.
Span and ZeroOutput Code SSpan and zero may be accessed with local adjustments or remotely through a HART-compatible Interface.Output Codes E, G, J, L, and MSpan and zero are continuously adjustable.
Zero Elevation and SuppressionOutput Codes S, E, and GZero elevation and suppression must be such that the lower range value is greater than or equal to the (–URL) and the upper range value is less than or equal to the (+URL). The calibrated span must be greater than or equal to the minimum span and less than or equal to the maximum span.
Output Code JZero is adjustable up to 10% of the calibrated flow span.
Output Code LZero is adjustable ±10% of URL and span is adjustable from 90 to 100% of URL.
Output Code MZero is adjustable ±50% of URL and span is adjustable from 50 to 100% of URL.
Model 1151 Alphaline ® Pressure Transmitters
Model1151
Pressu
TABLE 2. Rangeability.
Output CodeMinimum Span
(URL=Upper Range Limit)Maximum Span
S (DP and GP, SST, Range 3–8; HP SST, Range 4–7) URL/15 2 3 URL(1)
(1) Transmitter is capable of measuring from –URL to URL.
S (All Others) URL/6 2 3 URL(1)
E, G, J URL/6 URL
L URL/1.1 URL
M URL/2 URL
TABLE 3. Model 1151 Transmitter Range Availability by Model (URL = Upper Range Limit).
Range Code Model 1151 Ranges (URL) DP HP GP DP/GP/Seals AP LT
Code Model 1151 Output Options/Damping DP HP GP DP/GP/Seals AP LT
S 4–20 mA, Digital, Smart/Variable • • • • • •
E 4–20 mA, Linear, Analog/Variable • • • • • •
G 10–50 mA, Linear, Analog/Variable • • • • • •
J(1)
(1) Available with Ranges 3–5.
4–20 mA, Square Root, Analog/Variable • • NA NA NA NA
L 0.8 to 3.2 V, Linear, Low Power/Fixed • • • • • NA
M 1 to 5 V, Linear, Low Power/Fixed • • • • • NA
re-184
Rosemount Inc.
Mod
el11
51
Temperature LimitsElectronics Operating
Code S –40 to 185 °F (–40 to 85 °C).Code E –40 to 200 °F (–40 to 93 °C).Code G, L, M –20 to 200 °F (–29 to 93 °C).Code J –20 to 150 °F (–29 to 66 °C).
Sensing Element OperatingSilicone fill –40 to 220 °F (–40 to 104 °C).Inert fill 0 to 160 °F (–18 to 71 °C).
StorageCode S –60 to 185 °F (–51 to 85 °C).Codes E, G, L, M –60 to 250 °F (–51 to 121 °C).Code J –60 to 180 °F (–51 to 82 °C).
Static Pressure and Overpressure LimitsModel 1151DP0 psia to 2,000 psig (0 to 13.79 MPa) on either side without damage to transmitter. Operates within specifications from static line pressures of 0.5 psia (3.45 kPa) to 2,000 psig (13.79 MPa).
Model 1151HP0 psia to 4,500 psig (0 to 31.02 MPa) on either side without damage to transmitter. Operates within specifications from 0.5 psia (3.45 kPa) to 4,500 psig (31.02 MPa).
TABLE 6. Fill Fluid Specifications.
Fill FluidTemperature
Limits (1)
(1) Temperature limits are reduced in vacuum service. Contact yourlocal Rosemount representative for assistance.
SpecificGravity
Coeff. ofTherm. Exp.
cc/cc/°F(cc/cc/°C)
Viscosityat 25 °C
centistokes
D.C.® 200Silicone
–40 to 400 °F(–40 to 205 °C)
0.9340.00060
(0.00108)9.5
D.C. 704Silicone
60 to 400 °F(15 to 205 °C)
1.070.00053
(0.00095)44
Inert Fill–50 to 350 °F
(–45 to 177 °C)1.85
0.0004(0.000864)
6.5
Syltherm®
800, Silicone–50 to 400 °F
(–45 to 205 °C)0.934
0.00052(0.000936)
9.5
SylthermXLT, Silicone
–100 to 300 °F(–73 to 149 °C)
0.850.000666
(0.001199)1.6
GlycerinandWater(2)
(2) Glycerin and Water and Propylene Glycol and Water are notsuitable for vacuum service.
0 to 200 °F(–17 to 93 °C) 1.13
0.00019(0.00034) 12.5
PropyleneGlycolandWater(3)
(3) Not compatible with Buna-N or Ethylene-Propylene O-ringmaterial.
0 to 200 °F(–17 to 93 °C)
1.02
0.00019(0.00034)
2.85
NeobeeM-20(3)
0 to 400 °F(–17 to 205 °C)
0.9000.00056
(0.001008)9.8
Model 1151AP0 psia to 2,000 psia (0 to 13.79 MPa) without damage to transmitter. Operates within specifications from 0 psia to the upper range limit of the transmitter.
Model 1151GP0 psia to 2,000 psig (0 to 13.79 MPa) for ranges to 1,000 psig (6.90 MPa), 4,500 psig (31.02 MPa) for the 3,000 psig (20.68 MPa) range, and 7,500 psig (51.71 MPa) for the 6,000 psig (41.37 MPa) range, without damage to the transmitter. Operates within specifications from 0.5 psia (3.45 kPa) to the upper range limit of the transmitter.
Model 1151LT
Burst Pressure All Models10,000 psig (68.95 MPa) proof pressure on the flanges.Humidity Limits0 to 100% relative humidity.
Volumetric DisplacementLess than 0.01 in3 (0.16 cm3).
Failure Mode Alarm (Output Code S)If self-diagnosis detects a gross transmitter failure, the analog signal will be driven below 3.9 mA or above 21 mA to alert the user. High or low alarm signal is user selectable.
Transmitter Security (Output Code S)Activating the transmitter security function prevents changes to the transmitter configuration, including local zero and span adjustments. Security is activated by an internal switch.
TABLE 7. Flange Pressure Rating.
Standard Class/Rating Carbon SteelStainless
Steel
ANSI 150 285 psig(1)
(1) At 100 °F (38 °C); the rating decreases with increasingtemperature.
275 psig(1)
ANSI 300 740 psig(1) 720 psig(1)
ANSI 600 1,480 psig(1) 1,440 psig(1)
DIN PN 10–40 40 bar(2)
(2) At 248 °F (120 °C); the rating decreases with increasingtemperature.
40 bar(2)
DIN PN 10/16 16 bar(2) 16 bar(2)
DIN PN 25/40 40 bar(2) 40 bar(2)
Level4–20 mA
SaturationValue
4–20 mAAlarmValue
Low 3.9 mA 3.8 mA
High 20.8 mA 21.75 mA
Pressure-185
Model 1151 Alphaline ® Pressure Transmitters
Model1151
Pressu
Overpressure Alarm (Output Code S)If the sensor detects a negative overpressure value, the analog signal will be driven to 3.9 mA. If the sensor detects a positive overpressure value, the analog signal is driven to 20.8 mA.
DampingNumbers given are for silicone fill fluid at room temperature. The minimum time constant is 0.2 seconds (0.4 seconds for Range 3). Inert-filled sensor values would be slightly higher.
Output Code STime constant is adjustable in 0.1 second increments from minimum to 16.0 seconds.
Output Codes E and GTime constant continuously adjustable between minimum and 1.67 seconds.
Output Code JTime constant continuously adjustable between minimum and 1.0 second.
Output Codes L, MDamping is fixed at minimum time constant.
Model 1151LTTime constant continuously adjustable between 0.4 and 2.2 seconds with silicone oil fill, or 1.1 and 2.7 seconds with inert fill for flush models and electronics codes E or G.
Turn-on TimeMaximum of 2.0 seconds with minimum damping. Low power output is within 0.2% of steady state value within 200 ms after application of power.
Ranges 3 through 8, DP and GP transmitters;Ranges 4 through 7, HP transmitters
±0.1 of calibrated span for spans from 1:1 to 10:1 of URL. Between 10:1 and 15:1 of URL.
All other ranges and transmitters±0.25% of calibrated span.
Output Code S, square root mode
Output Codes E, G, L, and M±0.2% of calibrated span for Model 1151DP Ranges 3 through 5. All other ranges and transmitters, ±0.25% of calibrated span.
accuracy 0.02 URLspan--------------
0.1– % of calibrated span±=
0.2 0.05 URLspan-------------
×+ % of calibrated flow span±
re-186
Output Code J±0.25% of calibrated span.
StabilityOutput Code S±0.1% of URL for six months for DP and GP Ranges 3 through 8. (±0.25% for all other ranges and transmitters.)
Output Codes E and G±0.2% of URL for six months for Ranges 3 through 5. (±0.25 for all other ranges.)
Output Codes J, L, and M±0.25% of URL for six months.
Temperature EffectOutput Code S [–20 to 185 °F (–29 to 85 °C)]
For DP and GP transmitter Range 4 through 8;HP transmitter Range 4 through 7:
Zero Error = ±0.2% URL per 100 °F (56 °C)Total Error = ±(0.2% URL + 0.18% of calibrated span) per 100 °F; For Range 3, double the stated effects. For other ranges and transmitters follow analog temperature specifications (Output Code E).
Output Code E, G, L, and M[–20 to 200 °F (–29 to 93 °C)]
For Ranges 4 through 0Zero Error = ±0.5% URL per 100 °F.Total Error = ±(0.5% URL + 0.5% of calibrated span) per 100 °F; double the effect for Range 3.
Output Code JThe total output effect, whether at zero or full scale, including zero and span errors is ±1.5% of URL per 100 °F (56 °C). ±2.5% of URL per 100 °F (56 °C) for Range 3.
Static Pressure EffectDP Transmitters
Zero Error±0.25% of URL for 2,000 psi (13790 kPa) for Range 4 and 5 or ±0.5% for other ranges, correctable through rezeroing at line pressure.
Span ErrorCorrectable to ±0.25% of input reading per 1,000 psi (6895 kPa), or to ±0.5% for Range 3. For Output Code J, the span error is correctable to ±0.125% of output reading per 1,000 psi, or to ±0.25% for Range 3.
HP TransmittersZero Error±2.0% of URL for 4,500 psi (31027 kPa), correctable through rezeroing at line pressure.
Span ErrorCorrectable to ±0.25% of input reading per 1,000 psi (6895 kPa). For Output Code J, the span error is correctable to ±0.125% of output reading per 1,000 psi.
Rosemount Inc.
Mod
el11
51
Vibration Effect0.05% of URL per g to 200 Hz in any axis.
Power Supply EffectOutput Codes S, E, G, and JLess than 0.005% of output span per volt.
Output Codes L, MOutput shift of less than 0.05% of URL for a 1 V power supply shift.
Load EffectOutput Codes S, E, G, and JNo load effect other than the change in power supplied to the transmitter.
Output Codes L, MLess than 0.05% of URL effect for a change in load from 100 kV to infinite ohms.
Short Circuit Condition (Low Power Only)No damage to the transmitter will result when the output is shorted to common or to power supply positive (limit 12 V).
EMI/RFI EffectOutput shift of less than 0.1% of span when tested to SAMA PMC 33.1 from 20 to 1000 MHz and for field strengths up to 30 V/m. (Code J is 0.1% of flow span.)
Mounting Position EffectZero shift of up to 1 inH2O (0.25 kPa). Range 3 transmitters with Output Code J should be installed with the diaphragm in the vertical plane.
With liquid level diaphragm in vertical plane, zero shift of up to 1 inH2O (0.25 kPa). With liquid level diaphragm in horizontal plane, zero shift of up to 5 inH2O (1.25 kPa) plus extension length on extended units. All zero shifts can be calibrated out. No effect on span.
Isolating Diaphragms316L SST, Hastelloy C-276, Monel, gold-plated Monel, or Tantalum. See ordering table for availability per model type.
Drain/Vent Valves316 SST, Hastelloy C, or Monel. See ordering table for availability per model type.
Process Flanges and AdaptersPlated carbon steel, 316 SST, Hastelloy C, or Monel. See ordering table for availability per model type.
Wetted O-ringsViton® (other materials also available). With gold-plated Monel diaphragms (diaphragm Code _6), special fluorocarbon O-rings are supplied.
Non-wetted MaterialsFill FluidSilicone oil or inert fill.
Bolts and Bolting Flange (GP and AP only)Plated carbon steel.
Electronics HousingLow-copper aluminum. NEMA 4X.
Cover O-ringsBuna-N.
PaintPolyurethane.
Process Connections1/4–18 NPT on 2.125-in. (54-mm) centers on flanges for Ranges 3, 4, and 5.1/4–18 NPT on 2.188-in. (56-mm) centers on flanges for Ranges 6 and 7.1/4–18 NPT on 2.250-in. (57-mm) centers on flanges for Range 8.1/2–14 NPT on adapters.
For Ranges 3, 4, and 5, flange adapters can be rotated to give centers of 2.0 in. (51 mm), 2.125 in. (54 mm), or 2.250 in. (57 mm).
Electrical Connections1/2–14 NPT conduit with screw terminals and integral test jacks compatible with miniature banana plugs (Pomona 2944, 3690, or equivalent). The HART Hand-Held Interface connections are fixed to the terminal block on smart transmitters.
Weight12 lb (5.4 kg) for AP, DP, GP, and HP transmitters, excluding options.
Meter Option: Add 2 lb (1 kg).Hazardous Locations CertificationsStainless steel certification tag is provided.
Factory Mutual (FM) ApprovalsFM Explosion Proof tag is standard. Appropriate tag will be substituted if optional certification is selected.
TABLE 8. Flange Weights with Model 1151LT Transmitter.
Flange (1)
(1) Stainless steel flange weights are listed.
Flush2-in
(50mm)Ext.
4-in.(100mm)
Ext.
6-in.(150mm)
Ext.
2-in., Class 1503-in., Class 1504-in., Class 1502-in., Class 3003-in., Class 3004-in., Class 3002-in., Class 6003-in., Class 600
Default Explosion Proof: Class I, Division 1, Groups B, C, and D. Dust-Ignition Proof: Class II, Division 1, Groups E, F, and G. Suitable for use in: Class III, Division 1. Indoor and outdoor use. NEMA 4X. Factory Sealed.
I5 Intrinsic Safety and Non-incendive Approvals: FM certifications optional for specific Classes, Divisions, and Groups when connected in accordance with the FM entity approvals,see Table 9. Factory Sealed.
K5 Combination of Explosion Proof, Intrinsic Safety, and Non-incendive Approvals.
Canadian Standards Association (CSA) ApprovalsE6 Explosion proof for Class I, Division 1, Groups
C and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1 Hazardous Locations. Certified for Class I, Division 2, Groups A, B, C, and D; CSA enclosure type 4X. Factory Sealed.
I6 Intrinsic Safety Approvals CSA certifications optional for specific Classes, Divisions, and Groups when connected in accordance with the CSA barrier selection table, Table 10. Temperature Code T2D.
C6 Combination of I6 and E6, CSA Explosion Proof and Intrinsic Safety Approval. Factory Sealed.
K6 CSA/CENELEC Explosion-Proof and Intrinsic Safety Approval.
Standards Association of Australia (SAA)Flameproof CertificationE7 Flameproof
Ex d IIB + H2 T6.Class I, Zone 1.
Dust-Ignition proofDIP T6.Class II.
Special Conditions: For transmitters having NPT or PG cable entry threads, an appropriate flameproof thread adaptor shall be used to facilitate application of certified flameproof cable glands.
I7 Intrinsically SafeEx ia IIC T6 (Tamb = 40 °C).Ex ia IIC T5 (Tamb = 70 °C).Class I, Zone 0.Special Conditions: Observe electrical connection parameters when installing transmitter.
Standards Association of Australia (SAA)
N7 Type NEx n IIC T6 (Tamb = 40 °C).Ex n IIC T5 (Tamb = 70 °C).Class I, Zone 2.
re-188
Special Conditions: The equipment must be connected to a supply voltage which does not exceed the rated voltage. The enclosure end caps must be correctly fitted whilst the equipment is energized.
CESI/CENELEC Flameproof CertificationE8 90.C.016: EEx d IIC T6 (without meter).
Special Conditions: When transient protection terminal options (R1 or R9) are installed, the transmitter must be supplied from a galvanically isolated i.s. barrier.
EEx ia IIC T5 (Tamb = 40 °C).EEx ia IIC T4 (Tamb = 80 °C).AnalogEEx ia IIC T5.
Special Conditions: When transient protection terminal options (R1 or R9) are installed, the transmitter must be supplied from a galvanically isolated i.s. barrier.
BASEEFA Type N (Non-incendive) CertificationN1 Smart
Ex N II T5 (Tamb = -40 °C to 50 °C); Un = 45 V.Ex N II T4 (Tamb = -40 °C to 80 °C); Un = 45 V.
AnalogEx N II T5; Un = 45 V.
Special Conditions: The apparatus must be installed in accordance with BS 5345: Part 7: 1979 and be earthed by means of enclosure earth terminal.
Schweizerischer Elektrotechnischer Verein (SEV)Intrinsic Safety CertificationIC Smart
EEx ia IIC T5 (Tamb = 40 °C).EEx ia IIC T4 (Tamb = 80 °C).
AnalogEEx ia IIC T6 (Pmax = 0.35 W).EEx ia IIC T5 (Pmax = 0.65 W).EEx ia IIC T4 (Pmax = 0.95 W).
Rosemount Inc.
TABLE 9. FM Entity Approvals.
1151 ParametersEquipment Associated
Parameters
FM Approved for Class I, II, III, Division 1 and 2 Groups
Any CSA Approved Barrier ≤ 30 V, ≥ 150 V NA NA • •
Mod
el11
51
MODEL 1151 SMART RETROFIT KIT
In keeping with the Rosemount Inc. design philosophy of upgrading products without sacrificing parts compatibility, the Model 1151 Pressure Transmitter, can be converted to microprocessor-based or “smart” operation. With its wide range of product offerings and low cost of ownership, the Model 1151 is a perfect candidate for smart retrofitting, and the Model 1151 Smart Retrofit Kit makes this possible.
Smart electronics can be installed quickly by removing the analog electronics boards and plugging
in a new, single-board smart electronics assembly. The electronics in the smart retrofit kit are identical to the electronics used in the Model 1151 Smart and feature the same advantages of the factory-produced smart transmitter.
Retrofitting ProcedureAny Model 1151 Differential, Gage, Absolute, or
Level Transmitter, Ranges 3–0, can be retrofitted with smart electronics. The retrofitting procedure takes just a few minutes. The five simple steps for converting a Model 1151 Analog Transmitter to smart operation are as follows:
Step 1 Remove the screws and unplug the analog electronics.
Step 2 Insert two spacers and reattach the header board.
Step 3 Plug in the smart electronics and secure with three screws.
Step 4 Attach eyelets to the terminal block to allow easy connection of the HART Communicator.
Step 5 Characterize the transmitter.For more information, see PDS 00813-0100-4594, Model 1151 Pressure Transmitter Smart Retrofit Kit, or consult your Rosemount Representative.
(1) Bolts and conduit plugs are plated carbon steel.
DP HP GP(2)
(2) On GP and AP transmitters, the low-side flange is plated carbon steel.For a stainless-steel low-side flange, order process connection Option Code D6.
AP(2)
525354555612222324252633(3)
3435
(3) These selections meet NACE material recommendations per MR 01-75.
Analog Scale, Linear Meter, 0–100%Analog Scale, Square Root Meter, 0–100% FlowAnalog Scale, Linear Meter, Special ScaleLCD Meter, Linear Meter, 0–100%, User SelectableAnalog Scale, Square Root Meter, 1–10√LCD Meter, Linear Meter, Special ConfigurationLCD Meter Square Root Meter, 0–100% FlowLCD Meter, Square Root Meter, 0–10√
••••••••
••••••••
•—••—•——
•—••—•——
(1) Bolts and conduit plugs are plated carbon steel.
(2) On GP and AP transmitters, the low-side flange is plated carbon steel.For a stainless-steel low-side flange, order process connections Option Code D6.
(3) These selections meet NACE material recommendations per MR 01-75.
(4) Not available with Output Codes L or M, or Option Codes Zx, V2, or V3.
(5) Not available with Output Codes J, L, M, or Option Codes Zx, V2, or V3.
(6) Not available with Output Codes G, L, M, or Option Codes Zx, V2, or V3.
(7) Not available with Output Codes G, J, L, M, or Option Codes Zx, V2, or V3.
(2)
Pressure-193
Model 1151 Alphaline ® Pressure Transmitters
Model1151
Pressu
TABLE 12. (continued).
Code Certifications (optional - select one) DP HP GP AP
I5(1)
K5C5(2)
C6(1)
K6E4E7E8I1(3)
I7(4)
I8(5)
N1(6)
N7IC(3)
Q4Q8(7)
Factory Mutual (FM) Non-incendive and Intrinsic Safety ApprovalFactory Mutual (FM) Explosion-Proof and Intrinsic Safety CombinationIndustry and Science Canada (ISC) Approval (Available in Canada Only)Combination of I6 and E6; CSA Explosion-Proof and Intrinsic Safety Approval
(Requires 42.4 V dc max. power supply)CSA/CENELEC Explosion-Proof and Intrinsic Safety ApprovalJapanese Industrial Standards (JIS) Flameproof CertificationStandards Association of Australia (SAA) Flameproof CertificationCESI/CENELEC Flameproof CertificationBASEEFA Intrinsic Safety CertificationStandards Association of Australia (SAA) Intrinsic Safety CertificationCESI/CENELEC Flameproof CertificationBASEEFA Type N CertificationStandards Association of Australia (SAA) Non-incendive Safety ApprovalSchweizerischer Elektrochnischer Verein (SEV) Intrinsic Safety CertificationCalibration Data SheetMaterial Traceability per EN 10204 3.1B
•••
•••••••••••••
•••
•••••••••••••
•••
•••••••••••••
•••
•••••••••••••
Code Housing DP HP GP AP
H1(8)
H2(8)
H3H4C1C2J1
SST Non-wetted Parts on Transmitter without MeterSST Non-wetted Parts on Transmitter with MeterSST Housing, Covers, Conduit Plug, Lock-nut, Without MeterSST Housing, Covers, Conduit Plug, Lock-nut, With MeterPG 13.5 Conduit Threads (Available in Germany Only)M20 Conduit Threads (Available in Germany Only)G½ Conduit Threads
•••••••
•••••••
•••••••
•••••••
Code Terminal Blocks DP HP GP AP
R1 Integral Transient Protection (Only available with Option Code S and E electronics) • • • •
Code Bolts for Flanges and Adapters (optional - select one) DP HP GP AP
L3L4L5
ASTM A193-B7 Flange and Adapter Bolts316 SST Flange and Adapter BoltsASTM A193-B7M Flange and Adapter Bolts
•••
•••
•••
•••
(1) Not available with Output Code G or Option Code Zx.
(2) Not available with Option Codes M1–M9.
(3) Not available with Output Codes G, J, L, M, or Option Code Zx.
(4) Not available with Output Code G or Option Code Zx.
(5) Not available with Output Codes G, J, L, M, S, or Option Code Zx.
(6) Not available with Output Codes G, L, M, or Option Code Zx.
(7) This option is available for the transmitter flange and adapters.
(8) Option includes SST housing, covers, conduit plug, locknut, L4 bolting, and D6 low side blank flange for GP and AP transmitters.Option Codes L4 and D6 parts are included with housing Option Codes H1 and H2.
NOTEFM explosion-proofapproval is standard.
re-194
Rosemount Inc.
TABLE 12. (continued).
Code Process Connections (optional (1)) DP HP GP AP
D1
D2
D3
D4
D5
D6
D9
G1G2G3G4G5G6K1(2)
K2(2)
S1(3)
S2(3)
S4(4)
Side Drain/Vent, Top
Side Drain/Vent, Bottom
Process Adapters Deleted
Conformance to DIN 19213 and DIN 50049 3.1B Ranges 3, 4, 5(Available in Germany Only)Conformance to DIN 19213 and DIN 50049 3.1B Ranges 6, 7, 8, without¼ NPT Threads or Drain/Vent Valve Connections (Available in Germany Only)316 SST Low Side Blank Flange
JIS Process Connection–RC ¼ Flange with RC ½ Flange Adapter
DIN Spacing (Single Entry Port, No Side V/D Hole Flange)DIN Spacing (Single Entry Port, Two Side V/D Hole Flange)DIN Spacing (Dual Entry Port, No Side V/D Hole Flange)DIN Spacing (Dual Entry Port, One Top Side V/D Hole Flange)DIN Spacing (Dual Entry Port, One Bottom Side V/D Hole Flange)DIN Spacing (Dual Entry Port, Two Side V/D Hole Flange)Kynar insert, ¼–18 NPTKynar insert, ½–14 NPTAttachment of One Remote Seal - See PDS 00813-0100-4016Attachment of Two Remote Seals - See PDS 00813-0100-4016Attachment of Integral Orifice Assembly - See PDS 00813-0100-4686
(2) The maximum working pressure on this option is 300 psig. Available only with materials of construction Option Codes 1x or 2x.
(3) This option may only be used on Ranges 4–8.
(4) This option has a maximum static pressure rating of 3,000 psi, and is available for factoryassembly only without associated piping and is available only for Ranges 2, 3, 4, and 5.
Software ConfigurationHydrostatic Testing, 150% Maximum Working PressureCleaning for Special ServiceCleaning for <1 PPM Chlorine/FluorineCalibrate at Line PressureCalibrate at Specific TemperatureImproved Temperature CoefficientCalibrate to 0.1% Accuracy
••••••••
••••••••
•••——•••
•••—••——
Code Outputs DP HP GP AP
V1(7)
V2(8)
V3(8)
Z1(9)
Z2(9)
Z3(9)
Reverse Output4–20 mV Test Signal20–100 mV Test Signal4-wire, 0–20 mA Output4-wire, 0–16 mA Output4-wire, 0–10 mA Output
—•••••
—•••••
••••••
—•••••
Typical Model Number: 1151DP 4 S 52 B3 M1
(1) Contains a Hastelloy spring that is wetted by the process; consult factory for Teflon O-ring without a spring.
(2) Available with Output Code S only.
(3) Hydrostatic testing for Range 0, 125% maximum working pressure.
(4) Fluorolube® grease on wetted O-rings.
(5) Not available on Range 10: limited to 1,500 psi on Range 9; not applicable with Output Code S.
(6) Available only with stainless steel isolators and for span of 10 inH2O and greater;not applicable with Output Code S; available only with Output Codes E, G, L, or M;not available on AP or DR transmitters.
(7) Reverse output option is not needed with smart electronics; configured via HART-based communicator.
(8) Not available with Output Codes L or M.
(9) Not available with Option Codes Mx, Vx, Ix, or Ex, or Output Codes G, L, M, or S.
re-196
Rosemount Inc.
Mod
el11
51
TABLE 13. Model 1151LT Flange-Mounted Liquid Level Transmitter.
Code Process Fill—High Pressure Side Temperature Limits
ACDHGNPS
Syltherm XLT –100 to 300 °F (–73 to 135 °C)D. C. Silicone 704 60 to 400 °F (15 to 205 °C)D. C. Silicone 200 –40 to 400 °F (–40 to 205 °C)Inert –50 to 350 °F (–45 to 177 °C)Glycerin and Water 0 to 200 °F (–17 to 93 °C)Neobee M-20 0 to 400 °F (–17 to 205 °C)Propylene Glycol and Water 0 to 200 °F (–17 to 93 °C)Syltherm 800 –50 to 400 °F (–45 to 205 °C)
re-198
Rosemount Inc.
Mod
el11
51
TABLE 13. (continued).
Code Options (see complete approvals descriptions)
S1(1)
M1(2)
M3(2)
M4(2)
M7(2)
E6I5(3)
K5I6(1)
C5(4)
C6(1)
K6E4E7E8I1(5)
I7(1)
I8(6)
N1(7)
N7IC(3)
W5Q4Q8(8)
V1V2V3Z1(9)
Z2(9)
Z3(9)
F_
One Remote Seal Selected from PDS 00813-0100-4016METERSLinear Meter, 0–100% ScaleSpecial Scale Meter, Specify RangeLCD Meter, 0–100%LCD Meter, Linear, Special ConfigurationHARZARDOUS LOCATIONS CERTIFICATIONSCanadian Standards Association (CSA) Explosion-Proof ApprovalFactory Mutual (FM) Non-incendive and Intrinsic Safety ApprovalFactory Mutual (FM) Explosion-Proof and Intrinsic Safety CombinationCanadian Standards Association (CSA) Intrinsic Safety ApprovalIndustry and Science Canada (ISC) Approval (Available in Canada Only)Combination of I6 and E6; CSA Explosion-Proof and Intrinsic Safety Approval(Requires 42.4 V dc max. power supply)CSA/CENELEC Explosion-Proof and Intrinsic Safety ApprovalJapanese Industrial Standards (JIS) Flameproof CertificationStandards Association of Australia (SAA) Flameproof CertificationCESI/CENELEC Flameproof CertificationBASEEFA Intrinsic Safety CertificationStandards Association of Australia (SAA) Intrinsic Safety CertificationCESI/CENELEC Flameproof CertificationBASEEFA Type N CertificationStandards Association of Australia (SAA) Non-incendive Safety ApprovalSchweizerischer Elektrochnischer Verein (SEV) Intrinsic Safety CertificationOTHER OPTIONSCopper O-ring for Vacuum Service (Nonwetted)Calibration Data SheetMaterial Traceability per EN 10204 3.1BReverse Output4–20 mV Test Signal20–100 mV Test Signal4-wire, 0–20 mA Output4-wire, 0–16 mA Output4-wire, 0–10 mA OutputSelect One Code from Flushing Connections Lower Housing Option Table 14.
Typical Model Number: 1151LT 4 S A0 A 52 D F1
(1) For welded capillary assemblies, order sensor module and low-side materials of construction Option Code 22(refer to PDS 00813-0100-4016 for more information).
(2) Not available with Option Codes Zx, V2, or V3.
(3) Not available with Output Code G or Option Code Zx.
(4) Not available with Option Codes M1–M9.
(5) Not available with Output Codes G, J, L, M, or Option Code Zx.
(6) Not available with Output Codes G, J, L, M, S, or Option Code Zx.
(7) Not available with Output Codes G, L, M, or Option Code Zx.
(8) Available for the diaphragm, upper housing, flange, adapter, extension, and lower housing.
(9) Not available with Option Codes Mx, Vx, Ix, or Ex, or Output Codes G, L, M, or S.
NOTEFM explosion-proofapproval is standard.
TABLE 14. Flushing Connections Lower Housing Options. • available – not available
(1) Not available with high pressure side Option Codes A0, B0, and G0.
(2) Not available with high pressure side Option Code G0.
SSTSST
Hastelloy C-276Hastelloy C-276
SSTHastelloy C-276
SSTSST
Hastelloy C-276Hastelloy C-276
1212001212
¼-18 NPT¼-18 NPT¼-18 NPT¼-18 NPT
——
½-14 NPT½-14 NPT½-14 NPT½-14 NPT
•••••••
••••
——••••
••••
——••••
Pressure-199
-Rosemountore Pte Ltd.an Crescent
Model1151
Pressu
Rosemount Inc.8200 Market BoulevardChanhassen, MN 55317 USA
Fisher-Rosemount LimitedHeath Place Bognor Regis
FisherSingap1 Pand
STANDARD ACCESSORIESAll models are shipped with flange adapters, drain/vent valves, and one instruction manual per shipment.
TaggingThe Alphaline Pressure Transmitter will be tagged, at no charge, in accordance with customer requirements. All tags are stainless steel. The standard tag is wired to the transmitter. Tag character height is 0.125 in. (0.318 cm). A permanently attached tag is available upon request.
CalibrationTransmitters are factory calibrated to the customer’s specified range. If calibration is not specified, the transmitters are calibrated at maximum range. Calibration is performed at ambient temperature and pressure.
Optional Three-Valve ManifoldsPart No. 01151-0150-0001:3-valve manifold, carbon steel for DP (Ranges 3–5), HP (Ranges 4–5). (Anderson, Greenwood & Co., M4AVIC-TR-68).
Part No. 01151-0150-0002:3-valve manifold, 316 SST with carbon steel bolts for DP (Ranges 3–5), HP (Ranges 4–5). (Anderson, Greenwood & Co., M4AVIS-TR-68).
RETROFIT KIT ORDERING INFORMATIONSpecify the 01151-0935-0001 Smart Retrofit Kit. A complete kit includes the following items:
1 Model 1151 Smart Transmitter electronics1 Electronics cover and O-ring
Other Model 1151 Literature00813-0100-4593Model 1151 Smart Pressure Transmitters
00813-0100-4294Model 1151DR Draft Range DifferentialPressure Transmitter
(Pressure-231)Filled Systems for Pressure Transmitters
00813-0100-4594Model 1151 Smart Retrofit Kit
Rosemount, the Rosemount logotype, and SMART FAMILY are registeredtrademarks of Rosemount Inc.HART is a registered trademark of the HART Communication Foundation.d-Cell, Rosemount System 3, and RMV9000 are trademarks of Rosemount Inc.Fluorolube is a registered trademark of Hooker Chemical Co.Hastelloy, Hastelloy C, and Hastelloy C-276 are registered trademarks of CabotCorp.Monel is a registered trademark of International Nickel Co.Viton is a registered trademark of E.I. du Pont de Nemours & Co.Neobee M-20 is a registered trademark of Stepan Chemical Co.Syltherm and D.C. are registered trademarks of Dow Corning Corp.Teflon is a registered trademark of E.I. du Pont de Nemours & Co.Aflas is a registered trademark of Asahi Glass Co., Ltd.Kynar is a trademark of Pennwalt Inc.
