Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955 [email protected] • Remove connecting screw from flap hinges . This will form 2 halves for the following assembly steps. Connecting screw
AI-04 08/07 issue 181737 ASSEMBLY INSTRUCTIONS Alphason Designs Limited Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK Tel: +44 (0)1942 885600 Fax: +44 (0)1942 876955 [email protected]www.alphasondesigns.com Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support. Please Note: Maximum load for this support is 100Kg. This support must be assembled in accordance with these assembly instructions. Maximum load for each glass shelf is 50kg. A HAMMER CROSS-HEAD SCREWDRIVER PLEASE NOTE OTHER TOOLS REQUIRED: MODEL: ABR1100 AV CABINET IMPORTANT INFORMATION! 1) Before starting assembly please take time to familiarise yourself with the instructions and the components listed on the back page, as this product could be unstable if incorrectly installed. 2) Do not place hot or cold items against or in close proximity to any glass surface unless an adequately thick insulating material is used to prevent such items coming into contact with the glass. 3) Do not strike the glass with hard or pointed items. 4) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if necessary; do not use washing powders or other substances containing abrasives as these may scratch the glass. 5) Do not sit or stand upon horizontal glass surfaces. 6) In order to maintain a high quality finish, when cleaning wooden panels please use a soft cloth with a suitable furniture polish if required. 7) Alphason Designs uses real wood veneers, consequently slight colour and pattern variation may occur and does not indicate a product defect. With natural wood, exposure to direct sunlight can produce colour change and should be avoided. Any slight change in colour over time does not indicate a product defect.
Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.
Please Note:Maximum load for this support is 100Kg.This support must be assembled in accordance with these assembly instructions.Maximum load for each glass shelf is 50kg.
A HAMMER
CROSS-HEAD SCREWDRIVER
PLEASE NOTE OTHER TOOLS REQUIRED:
MODEL: ABR1100AV CABINET
IMPORTANT INFORMATION!1) Before starting assembly please take time to familiarise yourselfwith the instructions and the components listed on the back page,as this product could be unstable if incorrectly installed.2) Do not place hot or cold items against or in close proximity toany glass surface unless an adequately thick insulating material isused to prevent such items coming into contact with the glass.3) Do not strike the glass with hard or pointed items.4) When cleaning glass panels use a damp cloth or leather withwashing up liquid or soft soap if necessary; do not use washingpowders or other substances containing abrasives as these mayscratch the glass.5) Do not sit or stand upon horizontal glass surfaces.6) In order to maintain a high quality finish, when cleaningwooden panels please use a soft cloth with a suitable furniturepolish if required.7) Alphason Designs uses real wood veneers, consequently slightcolour and pattern variation may occur and does not indicate aproduct defect. With natural wood, exposure to direct sunlightcan produce colour change and should be avoided. Any slightchange in colour over time does not indicate a product defect.
STAGE 1
•
Place base panel on its back edge, on a
clean flat surface to avoid scratching. Using
screws attach panels to panel .
Attach panels to panel using screws
. Ensure these panels do not obscure
the slot at the back of base panel .
Insert 4x cams into large holes in panel
. Ensure arrows are pointing to the
outside edge of the panel.
Assemble side panels and onto base
panel . Tighten cams in base panel .
STAGE 2
•
STAGE 3
•
A
D
D
AI-04 08/07issue 181737
A
F A
CF
C
STAGE 4
Screw all remaining dowels into top panel .
Take care not to over tighten.
x4 x4 x4
x8
4.4.
•
A
C DA
• Slot back panel into grooves in sides of panels
and , and base panel .E
C D A
Ensure back panel is correctly located before
proceeding to next stage.
• E
3.3.
x8
x4
C
D
F
A
F
D
C
Position all remaining cams in panels ,
and . Once again ensure the arrows are
pointing to the outside edge.
1.1.Screw dowels x4 into side panels and .
A
•
•
•
E
2.2.A
C
D
F
v
v
v
w
w u y
y
y u
H
H
u
w
w
w
ww
v
B
B
v
v
A
Assemble top panel as shown in fig 5.
Ensure dowel fixings align with corresponding holes in panels
, and .
Tighten all cams from stage 3.
STAGE 5
•
D
AI-04 08/07issue 181737
•
•
5.
F
•
STAGE 8Using screws attach part ii flap hinges in to therebates in the cabinet base panel .
STAGE 7• Using screws , screw part i from flap hinge into
the 3 corresponding rebates in the cabinet door .
Using screws attach both door plates at eitherside of the door .
7.
B
D
B
F
W
6. X10X6
C
C
Position location tape pieces around the
rebate in cabinet door ensure these are
equally spaced around the rebate.
Place glass panel into the rebated area.
Ensure this is firmly stuck in place.
Fit all pine tree clips into correct holes in
the cabinet door . You may need a light
hammer to get these in to place. Take extra Take extra
care when carrying out this step.care when carrying out this step.
STAGE 6•
•
G
•
G!
• Remove connecting screw fromflap hinges . This willform 2 halves for the followingassembly steps.
Connectingscrew
8.
Use in stage 7 Use in stage 8
STAGE 6a 6a.
zz t
t
HH
z
p x2
r pG
mG
•G
p
m
m
p
mm
m
A
A
l
l
l
ll
l
l
tG
i ii iii
rr
Attach left and right hand flap stays and
using screws .
STAGE 9
•
Carefully lay the cabinet on its back. Push roller
glides into roller glide panels .
Turn cabinet around to sit on roller glides .
STAGE 10
•
•
10.
STAGE 11
Finally insert shelf pegs into desired positions in the side panels.(Only shown in one position.)
Place glass shelves and into position.
Attach 1 door buffer to the top end
of each side panel and .
11.
•
•
n or
x12
x6
AI-04 08/07issue 181737
The braking force of the flap stays may require adjustment. This can be achieved by turning the screw arrowed clockwise to tighten the movement or anticlockwise to loosen the movement.
aa
aa
J K
s
sl
lss
9.
x2 Using connecting screw , attach both left and
right hand flap stays to the door plates .
•
Carefully assemble the door onto the base
panel.
Re-Connect hinges by using connecting
screw from stage 6a.
•
12.
STAGE 12
13. STAGE 13
r r
no
pqq
q
p
J
K
J
aa
l
l
x2bb
bb
bb
•
C D
bb
•
DESCRIPTION QTY PACKED BY
1
1
2
1
COMPONENT
MODEL: ABR1100
CERTIFICATE OF CONFORMITY
AI-04 08/07issue 181737
A
B
2
2
1
CENTRE PANELS
BACK PANEL
LEFT END PANEL
TOP PANEL
BASE PANEL
CABINET DOOR 1
GLASS SHELF
SMALL GLASS SHELF
C D
E
F
G
RIGHT END PANEL
2ROLLER GLIDE PANEL
GLASS PANEL FOR DOOR 1H
I
J
K
AI-04 08/07issue 181737
This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your
correspondence to the address given at the bottom of the front page.
3
18
RIGHT HAND FLAP STAY
1
1
2
12
10
4
12
12
1
FLAP HINGE(During assembly this hinge splits into 2 parts)
