2:: Introduction
:: KIT Features
:: Additional
:: Other Helpful Items
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10B5 Team Kit. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.
Features in the RC10B5 Team Kit:
• Narrowed composite tub chassis with centralized mass and optimized motor position for improved handling and balance
• Chassis fits R.O.A.R. approved 2S saddle packs and 2S short packs using optional foam insert
• V2 12mm “Big Bore” threaded aluminum shocks with 3mm shock shafts and updated O-rings for improved smoothness
• VTS (Variable Torque multi-plate Slipper) with 3 drive surfaces and high-resolution spring
• New transmission has stronger gears, precision ball bearings, and a 14 carbide ball differential for increased life and torque capacity
• Adjustable front suspension mount angle (kick-up) options of 25˚ and 30˚
• New front suspension features heavy duty steering and caster blocks, while the insert system allows for easy caster and trailing axle adjustments
• One piece front axle/hex adapter and larger front wheel bearing for added durability
• Updated full bearing steering system with horizontal ball studs for finer Ackermann adjustments
• Heavy-duty ball cups and ball studs allow for maximum suspension travel while reducing binding and friction
• Rear hubs feature larger bearings as well as the quick and easy insert system to adjust camber link position and rear toe-in.
• B5 clear body and wing included
Your new B5 Team Kit comes unassembledand requires the following items for completion (refer to catalog section for suggestions):• R/C two channel surface frequency radio system• AA-size batteries for transmitter (#302 alkaline)• Electronic Speed Control, ESC (#29140, #29143)• Steering servo (#29166, #29167) • R/C electric motor • Pinion gear, size determined by type/wind of motor• Battery charger (#604 LiPo compatible charger)• 2 cell LiPo battery pack (#314 square, #310 Saddle Pack, #602 Shorty)
• Calipers or a precision ruler • Needle nose pliers• Lexan specific spray paint• Reamer / hole punch • Tire glue (#1597) • Thread locking compound (#1596)• Tires and Inserts, Fronts and Rears
Tools included:• Allen wrenches 1.5mm, 2.0mm• #1113 12mm Shock Tool• Multi-wrench
• Silicone Shock Fluid (Refer to catalog for complete listings)• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters / Hobby Knife • Soldering Iron • 8 Piece Hex Driver Set (AE Part # 1655)• Needle Nose Pliers • Multi Tool (AE Part #7494)• 7mm Nut Driver • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
3:: Table of Contents
:: Notes
There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.
This symbol indicates a special note or instruction in the manual.
This symbol indicates a Racers Tip.
1................... Cover
2................... Introduction 3................... Table of Contents
4................... Front Top Plate and Steering Build (Bag A-AA)
5................... Front Arms and Uprights Build (Bag B)
6 - 7.............. Shock Towers and Rear Chassis Brace Build (Bag C)
7 - 8............. Differential Build (Bag D-DD)
8 - 9............. Gearbox Build (Bag E)
9 - 10.......... Slipper Build (Bag F-FF)
11................. Rear Hub and CVA Build (Bag G)
12................ Turnbuckles Build (Bag H-HH)
13 - 14........ Shocks Build (Bag I-II)
14 - 16........Electronics Build (Bag J)
16 - 17.........Wheels, Tires, and Body Build (Bag K)
18 - 20....... Tuning Tips
21 - 29....... Catalog
30................ Notes / Contact Info
31................ Setup Sheet “Kit Setup”
32................ 1:1 Hardware “Fold Out”
33................ Setup Sheet “Blank”
34................ Back Cover
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
!
12/13
:: Front Top Plate and Steering Build - Bag A - AA - Step 2
:: Front Top Plate and Steering Build - Bag A - AA - Step 3
4:: Front Top Plate and Steering Build - Bag A - AA - Step 1
Do not overtighten steering bolts. Make sure there is free movement in the steering rack.
914753 x 7 x 3
Ball Bearing
91391Steering
Rack
x4x2
x2
x2
x2
x2
91048Heavy-duty Ballstud,
8mm
25204M3 x 16mm
FHCS
91364Bulkhead
(25 °)
25202M3 x 10mm
FHCS
5407Red
O-Ring
31286FT Ballstud
Washer, aluminum
(2mm, blue)
There are two bulkheads included (25 °, 30 °). 25 ° is the standard one
used.
!
!
91391Steering Bellcrank
Brace
91360RC10B5Chassis
91391Steering Bellcrank
Brace
914753 x 7 x 3
Ball Bearing
x4
x2
x2
25189M3 x 22mm
BHCS
91362B5 Top Plate
89202M3 x 12mm
BHCS
91047Heavy-duty Ballstud,
6mm
Note orientation of steering rack.
!
Note orientation of the brace.
!
5:: Front Arms and Uprights Build - Bag B - Step 1
Build 2 (1 left, 1 right)
Trailing Axle Inserts
Build 2 (1 left, 1 right)
x2
91049Heavy-duty Ballstud, 10mm
31530M3 x 5mm
BHCS
25215M3 Locknut,
black
25215M3 Locknut,
black
252375 x 10 x 4Bearing
91406Front Axles
4670M3 x 8mm Set Screw
(not included in kit)
91400Caster
Block Insert(5°)
91407Front Axle Crush Tube
91047Heavy-duty Ballstud,
6mm
There are two caster block inserts
included (0°, 5 °). 5 ° is the standard one used.
!
91404Steering
Block Insert(2-4)
91404Steering
Block
91400Caster Block
31520M2.5 x 6mm
BHCS(not included in kit)
x2
There are multiple options for the trailing axle inserts. 4 is the stock setup.
Make sure the arrow is pointing forward for your desired selection.
Also make sure both the right and left sides are on the same setting.
You can install an optional #4670 set screw to better hold
the caster block inserts and hinge pin.
You can install an optional #31520 screw to use as a
steering stop setting.
!
:: Front Arms and Uprights Build - Bag B - Step 3
:: Front Arms and Uprights Build - Bag B - Step 2
Build 2 (1 left, 1 right) Build 2 (1 left, 1 right)
x2x2
89202M3 x 12mm
BHCS
31510M2 x 4mm
BHCS
91400Caster Block
Spacer
91402Caster Block
Bushing
91394Hinge Pin
(front, outer)
91398Front Arms
x2
2
4
6
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 3
91412Rear Arms
31521M2.5 x 8mm
BHCS
25187M3 x 14mm
BHCS
91379Chassis Plate
91382Arm Mount,
C (3+2)
91382Arm Mount,
D
x2
x2 91394Hinge Pin
(rear, Inner)
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 2
89204M3 x 24mm
BHCS
89202M3 x 12mm
BHCS
91477M3 Nut(black)
91373Front Shock
Tower
91049Heavy-duty
Ballstud, 10mm
x2
x4
x2
x231286FT Ballstud
Washer, aluminum
(2mm, blue)
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 1
25204M3 x 16mm
FHCS
91410Front
Bumper
91394Hinge Pin
(front, Inner)
91371Front Hinge Pin Brace
31521M2.5 x 8mm
BHCS
x2 x2
7
:: Differential Build - Bag D - DD - Step 16581
3/32 carbidediff balls
91419Diff Gear,
52T
7666Diff Drive
Ring
7666Diff Drive
Ring
x14
#6591diff lube#6591diff lube
#6591diff lube
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 5
89204M3 x 24mm
BHCS
x2 25211M3 x 10mm
BHCS
25187M3 x 14mm
BHCS
x2x2
91375Rear Shock
Tower
91433Rear Body
Mount
91477M3 Nut(black)
25201M3 x 8mm
FHCS
x2
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 4
25203M3 x 12mm
FHCS
91049Heavy-duty
Ballstud, 10mm
89208M3 x 14mm
FHCS
x2
x2
x2
91377Chassis Brace
x231286FT Ballstud
Washer, aluminum
(2mm, blue)
25211M3 x 10mm
BHCS
x2
91420Ball Diff Outdrive
91420Ball Diff Outdrive
8
:: Gearbox Build - Bag E - Step 1
252386 x 12 x 4,
Bearing
252375 x 10 x 4,
Bearing
91425Top Shaft
91426Top Shaft
Spacer
2561610 x 15 x 4,
Bearing
91424Gearbox
(right & left)
91429Idler Gear
910114x4 Idler
Gear Shaft
x2
x2
x2
:: Differential Build - Bag D - DD - Step 3As you tighten the diff bolt, you will notice the T-nut ears moving closer to the bottom of the outdrive slot. This compresses the
spring behind the T-nut. The spring should be completely compressed at the same time the T-nut reaches the end of the slot. Caution! Pay close attention to the feeling when the spring is completely compressed. Do not overtighten the bolt. When you feel the spring completely compressed, loosen the diff bolt
1/8” of a turn. Your diff should now operate smoothly with resistance as the outdrives move in opposite directions.
After you have driven the car once, re-check the diff setting.
6575Diff
cover
6575Locking
t-nut
6582Diff
thrust spring
Compress spring first.
!
:: Differential Build - Bag D - DD - Step 2
#6588
black grease
6573Diff thrust
washer
65745/64 diff
thrust balls
6573Diff thrust
bolt
x2
x6
314005 x 8mm,Bearing
x2
9
:: Slipper Build - Bag F - FF - Step 1
x2
7485FT V2
Slipper Hub
91177VTS Slipper
Pads
9603Slipper
Pad
965181T 48P
Spur Gear
91176VTS Slipper
Housing
91178VTS Slipper
Plate
91179VTS Slipper Hub, outer
25202M3 x 10mm
FHCS
x391428Motor Plate,
blue
:: Gearbox Build - Bag E - Step 3
91478M3 x 30mm
BHCS
91433Wing
Mounts
31532M3 x 8mm
BHCS
91432Motor Guard
x2
x2
:: Gearbox Build - Bag E - Step 2Install the Diff with
the head of the Diff Thrust Bolt
(#6573) facing the same side as the
spur gear.
Add a drop of Diff Lube (#6591) to
the teeth of the diff gear, idler gear, and
top shaft.
!
!
(#6573) facing the
the teeth of the diff gear, idler gear, and
89203M3 x 16mm
BHCS
x5
#6591
diff lu
be
There’s also a72T48P spur gear
(#9649)included for stock
motor use!
!
91428Motor Plate,
blue
There’s also a72T48P spur gear
(#9649)included for stock
motor use!
!
You can add black grease (#6588) to the screw threads to ease
screw installation.
10
:: Slipper Build - Bag F - FF - Step 4
25204M3 x 16mm
FHCS
25211M3 x 10mm
BHCS
x2
x2
:: Slipper Build - Bag F - FF - Step 3
25203M3 x 12mm
FHCS
x2
:: Slipper Build - Bag F - FF - Step 2
Set nut flush with top shaft.
See page 18 for gear mesh, and slipper clutch
setting instructions!
!
!
9739Slipper Spring
91148M4 Locknut, with flange and knurl
Set nut flush with top shaft.
!
91423Slipper Spring
Adapter
11
:: Rear Hub and CVA Build - Bag G - Step 3
91414Rear Hub
Spacer
91394Hinge Pin
(rear, outer)
4670M3 x 8mm Set Screw
(not included in kit)
31510M2 x 4mm
BHCS
x2
x2
Build x2 (right and left side)Build x2 (right and left side)
:: Rear Hub and CVA Build - Bag G - Step 291436
CVA Wheel Hex Pin
91441Wheel
Hex (rear)
91438CVA Pin
Build x2 (right and left side) Build x2 (right and left side)
:: Rear Hub and CVA Build - Bag G - Step 1
Build x2 (right and left side)
#6588
black grease
914766 x 13 x 5Bearing
2561610 x 15 x 4
Bearing91047Heavy-duty
Ballstud, 6mm
91414Rear Hub
Insert(0°)
91414Rear Hub Link Insert
(A)91414
Rear Hub
91438CVA
Coupler
91439CVA Bone
91437CVA Axle
91416Rear Hub Link Nut
(A)
There are multiple optional inserts
for the Rear Hub Insert (0°, 0.5 °, 1 °).0° is the standard
insert used.!
!
You can install optional #4670 set screws to
better hold the rear hub inserts and
hinge pin.
Rear Hub Link Setting:Up
Up
Down
Down
A
B
C
B
B
A
A
12
:: Turnbuckles Build - Bag H - HH - Step 3
Build x2 (right and left side)
Rear Camber Turnbuckle23.30mm
91453HD Ball Cup
(small)
91453HD Ball Cup
(small)
6263Turnbuckle,
2.06”HD Ball Cup
:: Turnbuckles Build - Bag H - HH - Step 2
Build x2 (right and left side)
Front Camber Turnbuckle23.85mm
91453HD Ball Cup
(small)
91453HD Ball Cup
(small)
6263Turnbuckle,
2.06”
:: Turnbuckles Build - Bag H - HH - Step 1
91453HD Ball Cup
(small)
91453HD Ball Cup
(right)
6263Turnbuckle,
2.06”
27.50mmSteering Turnbuckle
Build x2 (right and left side)
Racers Tip:
Use black grease (#6588) on the threads of the
turnbuckles for easier ball cup
installation!
Racers Tip:
Use black grease (#6588) on the threads of the
turnbuckles for easier ball cup
installation!
Racers Tip:
Use black grease (#6588) on the threads of the
turnbuckles for easier ball cup
installation!
Orient the notch to the left throughout the car. It indicates which end has the left hand threads!
!
Orient the notch to the left throughout the car. It indicates which end has the left hand threads!
!
Orient the notch to the left throughout the car. It indicates which end has the left hand threads!
!Install the ballstuds on
curved side of the ballcup!
!
Install the ballstuds on curved side of the ballcup!
!
Install the ballstuds on curved side of the ballcup!
!
13
:: Shocks Build - Bag I - II - Step 3
Step 9-10Step 8Step 6-7Step 4-5
Front Shock: 30 wt
Rear Shock: 30 wt
Step 2-3
Shock Bleeding Steps:1. Before assembly, get each bleed
screw and thread it 1-2 turns into the shock cap. This will make it easier when you are bleeding your shocks.
2. Pull shock shaft down.3. Fill shock body 3/4 full with silicone
shock fluid.4. Slowly move the shock shaft up and
down to remove air from under the piston.
5. Wait for bubbles to come to surface.6. Fill shock body to top with silicone
shock fluid.7. Place a drop of oil in the cap and on
cap threads.8. Install cap (without bleed screw) and
tighten completely.9. Slowly compress shaft all the way to
bleed excess silicone shock fluid out the hole in the cap (use rag around-shock to catch excess fluid).
10. Install M2x4mm button head screw until snug while shaft is fully com-pressed.
Shock oil#5422Sh
ock oil
#542231510
M2 x 4mm BHCS
:: Shocks Build - Bag I - II - Step 2
#1105green slime
91448Shock eyelet
91448Shock
Pivot Ball
9148012x23mm V2 Shock Bodies
(front)
9148212x31mm V2 Shock Bodies
(rear)
91491V2 Shock
Hat Bushing
91491V2 Shock Spacer
5407O-Ring
31327VCS3 Shock Bottom Cap
31327VCS3 Shock Bottom Cap
O-Ring
9149112mm
Shock Cap O-Ring
x2
x2
#1105green slime
Lightly rub shock oil on the o-ring before
installation!
Racers Tip:
Coating the o-rings with green slime
(#1105) helps seal & reduce o-ring
swell! Green slime not included in kit!
:: Shocks Build - Bag I - II - Step 1
9130812mm
Shock Piston (1.6 front)(1.7 rear)
914883 x 21
Shock Shaft (front)
914893 x 27.5
Shock Shaft (rear)
62991/8 E-Clip
62991/8 E-Clip
4187Nylon Spacer,
(.030) Racers Tip:
Use a marker over the numbers on the pistons to
make them easily visible!
Front:3 spacers
Rear:2 spacers
!
14
:: Shocks Build - Bag I - II - Step 5
:: Electronics Build - Bag J - Step 1
Use outside hole in
front arm!
!
7337Gold
Washer
91443Servo Mount
91455Servo
Spacers
91455Steering
Link
31532M3 x 8mm
BHCS
89009Servo Horn
Ring
91047Heavy-duty
Ballstud, 6mm
9180ServoHorn
x4
x2
x2
x4
Servo not included!
Servo screwnot included!
Use inside hole in
rear arm!
!
25612M3 Locknut, with flange
(black)
25612M3 Locknut, with flange
(black)
89202M3 x 12mm
BHCS
91445Shock
Bushing
91445Shock
Bushing
25189M3 x 22mm
BHCS
Build x2 (right and left side) Build x2 (right and left side)
31286FT Ballstud
Washer, aluminum
(1mm, blue)
:: Shocks Build - Bag I - II - Step 4
9130412mm
threaded collar
9130412mm
threaded collar o-ring
x4
x4
9131012mm shock spring cup
(5mm offset)9132712mm front
spring, Green (3.15lb)
9133712mm rear
spring, white (2.10lb)
Front: 4mm
Rear: 5.5mm
Build x2 front and x2 rear shocks
Racers Tip:
Use your finger to rub shock oil on the o-ring for
smoother adjustment!
A - AirtronicsF - FutabaH - HitecJ - JRPrinted here
Align the servo horn 90 degrees
!
15
:: Electronics Build - Bag J - Step 3
:: Electronics Build - Bag J - Step 4
Receiver not included!
Receiver not included!
ESC not included!
Pinion / Setscrewnot included!
See page 18 for gear mesh setting
instructions!!
91089Belt Cover
Cap
91435Gear Cover
(black)
31530M3 x 5mm
BHCS
6727Servo Tape
x2
:: Electronics Build - Bag J - Step 2
Motor not included!
31532M3 x 8mm
BHCS
31532M3 x 8mm
BHCS
x2
x2
x2
892183 x 8mmWasher
Use included optional
Receiver mount if ESC clearance
is needed
!Receiver not
included!
91380Receiver Mount
31532M3 x 8mm
BHCS
x26727
Servo Tape
16
:: Electronics Build - Bag J - Step 6
:: Wheels / Tires and Body - Bag K - Step 1
Tires / Insertsnot included!
Tires / Insertsnot included!
#1597
ca glue #1597
ca glue
x29695Buggy Rear Wheel Hex,
White
9690Buggy Front Wheel Hex,
White
x2
Carefully apply ca glue (tire adhesive) to the tire bead on both sides. Do
one side at a time, allow it to dry before gluing the
other side!CA glue not included!
!
Build x2 Build x2
:: Electronics Build - Bag J - Step 54689
M3 x 16mm Set Screw
x2
Batterynot included!
Batteriesnot included!
91458Battery Strap Thumb Wheel
91458Battery Strap Thumb Wheel
O-Ring
91456Battery Strap
x2
x2
91459Single Battery Spacer
91459Battery Spacer
91459Battery Spacer
There are two options for
mounting your antenna.
!
6338Antenna
Tube & Cap
25225M3 x 3mm Set Screw
17
:: Wheels / Tires and Body - Bag K - Step 3
:: Wheels / Tires and Body - Bag K - Step 4Painting Tips:
Your B5 Team Kit comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (use either rattle can or airbrush) the paint on the inside of the body (prefferably dark colors first, lighter colors last).
NOTE: ONLY use paint that is recommended for use with (polycarbonate) plastics. If you do not, you candestroy the plastic body!!!!.
After paint has completely dried, cut the body along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts and antenna!
Racers Tip:Instead of using the included body clips
(#21173), you can use hook and loop tape on the inside of the body, and the sides of
the chassis to keep your body in place!
21173Small
Body Clips
91470Clear
Body, B5
91433Wing Angle
Shim
91471Clear Wing,
B5
x2
21173Small
Body Clips
x2
:: Wheels / Tires and Body - Bag K - Step 2
Build 2 (1 left, 1 right) Build 2 (1 left, 1 right)
91148M4 Locknut, with flange and knurl
91148M4 Locknut, with flange and knurl
18:: Tuning TipsTips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.
Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change.
When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions. Peridicaly check all moving suspension parts. Suspension components must be kept clean and move freely without binding to prevent poor and/or inconsistent handling.
Slipper Clutch:
The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top shaft is even with the outside of the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in place and apply short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.
Ride Height:
Ride height is the distance from the ground to the bottom of the chassis.The standard front ride height setting is with the front arms level (reffered to as “arms level”) or 24mm (Ride Height Gauge #1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right arms appear to be level.
The rear ride height setting you should use most often is with the outdrive, driveshaft, and axles all on the same imaginary horizontal line (reffered to as “bones level”) or 24mm (Ride Height Gauge#1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right driveshafts appear to be level.
*Front arms should be in a straight line when ride height is set at “arms level”
!
*CVA bones should be in a straight line when ride height is set at “CVA bones
level”
!
Motor Gearing:
Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and electronic speed control manufacturers for more information. Team Associated is not responsible for motor damage due to improper gearing.
Set The Gear Mesh:
You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again. A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.
* These gearings are for use with advanced timing speed control settings!
23312230242322212121211918
Pinion
78698175818181818181818181
Spur
8.82:15.79:19.57:16.50:18.78:19.15:19.57:1
10.03:110.03:110.03:110.03:111.08:111.70:1
Final Drive Ratio
17.5 Reedy Sonic Brushless *17.5 Reedy Sonic Brushless
13.5 Reedy Sonic Brushless *13.5 Reedy Sonic Brushless10.5 Reedy Sonic Brushless9.5 Reedy Sonic Brushless8.5 Reedy Sonic Brushless7.5 Reedy Sonic Brushless6.5 Reedy Sonic Brushless
3300kV Brushless3900kV Brushless4900kV Brushless6100kV Brushless
MotorB5 Gear Ratio Chart (Internal Gear Ratio 2.60:1)
19:: Tuning Tips (cont.)
Caster:
Caster describes the angle of the kingpin as it leans toward the rear of the vehicle. Positive caster means the kingpin leans rearward at the top. The B5 includes two inserts to adjust caster angle at the caster block, 0° and +5°. The total caster angle is the sum of the kick-up angle and the caster block angle. Standard total caster angle for the B5 is 30°, with 25° kick-up and 5° caster block angle. For less entry steering and more exit steering, try 0° caster block angle.
Rear Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.Optional #1719 camber gauge can be used to more accurately set camber.
Front Camber Links:
Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link (or lowering the ball end) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response. Longer camber links are typically used on high grip tracks and shorter links tend to work better on medium-grip loose tracks.
*Raise or lower the ball end by adding
or subtracting washers here
!
Rear Camber Link:
Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the rear chassis brace. Shortening the camber link (or lowering the ball end) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ball end) will give the rear more roll and more cornering grip. Longer camber links are typically used on high grip tracks, while shorter links tend to work better on medium grip loose tracks. The kit setting is the best compromise of cornering grip and acceleration.
*Raise or lower the ball end by
adding or subtracting
washers here
!
Wheelbase Adjustment:
You have three options for rear hub spacing, Forward, Middle, & Back. The kit setting of Middle is the most neutral, and will be used most often. For improved handling in bumps or rhythm sections, try moving the hubs to the Back position. This can also make the car handle better in 180° turns.
*Spacers to the rear will place hubs for-ward, shortening the wheelbase
!
Front Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the front. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Positive camber, where the top of the tire is leaning out, is not recommended. Optional #1719 camber gauge can be used to more accurately set camber.
*Testing camber with camber gauge
!
Kickup:
Kickup is the angle the front suspension arm mounts at where the front of the arm is higher than the rear. The standard kickup angle for the B5 is 25°, and is most common. If more corner entry steering is desired, try the included 30° front bulkhead. It is important to adjust the bumpsteer to match the kickup angle adjustment. Refer to the chart below for some common settings:
KickupAngle
25° 1mm 0mm
30° 3mm 2mm 1mm
Less Agressive Bumpsteer Shims
Standard Bumpsteer Shims
More Agressive Bumpsteer Shims
N/A
20:: Tuning Tips
Ackermann:
Ackermann is the angle difference between the front wheels when they are turned to steer the car. For minimal tire slip, it is standard for the inside wheel to steer to a greater angle than the outside wheel. The B5 allows ackermann adjustments by changing the washer thickness used behind the steering rack ballstuds. The kit setup uses 2mm wash-ers and is most common for racing conditions. If corner entry steering is too aggressive, try increasing the ackermann by removing shims from behind the steering rack ballstuds. Increasing the ackermann will increase the angle difference of the front wheels when steered, resulting in a more stable car on corner entry.
Anti-Roll Bars:
The optional #91468 rear anti-roll bar kit (also called the “swaybar”) allows you to add roll resistance to the rear end with minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks (try the gold bar). The silver and black anti-roll bars are typically used on medium-grip loose tracks.
Trailing Axle:
Trailing axle is the distance from the king pin to the axle that “trails” behind the pin. The B5 includes inserts to allow adjustments for trailing axle to three positions: 4mm (standard), 3mm, and 2mm. The standard setup uses 4mm trailing axle for the most stable handling. For more corner entry steering, try the 3mm trailing axle option. It is important to adjust the ackermann and wheelbase settings to match the trailing axle adjustment. refer to the chart below for some common settings:
Trailing Axle Position
4mm
1mm
2mm
3mm
2mm
2mm
3mm
1mm
0mm
0mm 1mm (middle)
N/A 0mm (back)
1mm 2mm (forward)
# of Shimson Rack for
Less Ackermann
# of Shimson Rack for
Std. Ackermann
# of Shimson Rack for
More Ackermann
Rear Caster Block Wheelbase Shim
:: Shocks
:: Shock Springs
:: Ball Differential
:: Shock Oil
41875407629931327315109130491308913109144891449
91480914829148891489914919149691498
12812
2 ea.62
4 ea.4 ea.
44
2211122
913259132691327913289132991330913319133291333913349133591336913379133891339913409134191342913439134491345
Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.11111
5420542154225423542454255426542754285429543054315432543354345435543654375438
2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.
657365746575658165827666767731400914199142091421
261
1212121
1 ea.1
.030 Nylon WasherRed O-RingsE-ClipVCS3 Shock Bottom Cap and O-RingM2 x 4mm BHCS12MM Threaded Collar and O-Ring12MM Shock Pistons, (1.5, 1.6, 1.7)12MM Shock Spring Cups (+0mm, +5mm, +9mm)Shock Pivot Ball and Rod End12MM V2 Composite Shock Cap w/O-ring and bleeder screw12x23MM V2 Shock Bodies12x31MM V2 Shock Bodies3x21MM Shock Shaft3x27.5MM Shock Shaft12MM V2 Shock Rebuild Kit12x23B/21S V2 Shock Kit (B5 Front)12x31B/27.5S V2 Shock Kit (B5 Rear)
12MM Front SPRING BRN 2.8512MM Front SPRING BLK 3.0012MM Front SPRING GRN 3.15 - Kit12MM Front SPRING WHT 3.3012MM Front SPRING GRY 3.4512MM Front SPRING BLU 3.6012MM Front SPRING YLW 3.7512MM Front SPRING RED 3.9012MM Front SPRING ORN 4.0512MM Front SPRING PRL 4.2012MM Rear SPRING BLK 1.9012MM Rear SPRING GRN 2.0012MM Rear SPRING WHT 2.10 - Kit12MM Rear SPRING GRY 2.2012MM Rear SPRING BLU 2.3012MM Rear SPRING YLW 2.4012mm Big Bore Front Soft Spring Kit12mm Big Bore Front Medium Spring Kit12mm Big Bore Front Hard Spring Kit12mm Big Bore Rear Soft Spring Kit12mm Big Bore Rear Medium Spring Kit
10 Weight Silicone Shock Oil20 Weight Silicone Shock Oil30 Weight Silicone Shock Oil40 Weight Silicone Shock Oil22.5 Weight Silicone Shock Oil80 Weight Silicone Shock Oil27.5 Weight Silicone Shock Oil15 Weight Silicone Shock Oil25 Weight Silicone Shock Oil35 Weight Silicone Shock Oil45 Weight Silicone Shock Oil55 Weight Silicone Shock Oil32.5 Weight Silicone Shock Oil37.5 Weight Silicone Shock Oil42.5 Weight Silicone Shock Oil50 Weight Silicone Shock Oil60 Weight Silicone Shock Oil70 Weight Silicone Shock Oil47.5 Weight Silicone Shock Oil
Diff Thrust Washer & BoltPrecision Diff Thrust Balls, 5/64”Locking T-Nut, Diff Thrust Bolt, & Cover3/32” Carbide Diff BallsDiff Thrust SpringDiff Drive Rings, 2.60:1Ball Diff Rebuild KitBearing, 5 x 8mmDiff Gear, B5Ball Diff Outdrive, B5Ball Diff Kit, B5
21
6299
6299
91304
91304
91310
91448
9144831327
31327
5407
5407
91449
91491
91491
31510
9148891489
9148091482
4187
91308
91421
6582
91420
91420
91419
7666
6581
31400
31400
7666
6573
6573
6574
6575
6575
6575
22
:: Slipper Clutch74859603964896499650965196529653973931530910899114891175911769117791178911799142391435
2211111116241121121
FT V2 Slipper HubsSlipper Pad69T 48P Spur Gear72T 48P Spur Gear (Kit)75T 48P Spur Gear81T 48P Spur Gear (Kit)78T 48P Spur Gear84T 48P Spur GearSlipper SpringM3 x 5 BHCS4X4 Belt Cover CapM4 Locknut, w/flange and knurlFT VTS Slipper ConversionVTS Slipper HousingVTS Slipper PadsVTS Slipper PlateFT VTS Slipper Hub, outerSlipper Spring AdapterGear Cover (Black), B5
9739
9114831530
31530
91089
91435
7485 91179
91423
91176
91177
91177
91178
9603
96499651
:: Pinion Gears8253825482558256825782588259826082618263826482658266
826782688269827082718272
1111111111111
111111
16T 48P Pinion Gear17T 48P Pinion Gear18T 48P Pinion Gear19T 48P Pinion Gear20T 48P Pinion Gear21T 48P Pinion Gear22T 48P Pinion Gear23T 48P Pinion Gear24T 48P Pinion Gear 26T 48P Pinion Gear27T 48P Pinion Gear28T 48P Pinion Gear29T 48P Pinion Gear
30T 48P Pinion Gear31T 48P Pinion Gear32T 48P Pinion Gear33T 48P Pinion Gear34T 48P Pinion Gear35T 48P Pinion Gear
:: Transmission25202252032521125237252382561631532892038921891011914249142591426914289142991432
2020202226
10101111121
M3 x 10mm FHCSM3 x 12mm FHCSM3 x 10mm BHCSBearing, 5 x 10 x 4Bearing, 6 x 12 x 4Bearing, 10 x 15 x 4M3 x 8mm BHCSM3 x 16mm BHCWasher 3 X 8mm4x4 Idler Gear ShaftGearbox, B5Top Shaft, B5Top Shaft Spacer, B5Motor Plate (Blue), B5Idler Gear, B5Motor Guard, B5
3153231532
91432
2520325203
91424
9142425616
9101191429
25238
91425
91426
25238 25237
25237
25616
31532
31532
89218
89218
25202
25202
91428
25211
25211
89203
89203
89203
89203
23
:: Front Bulkhead / Steering540721173251892520231286
892029104791048913629139191475
Red O-RingSmall Body ClipsM3 x 22mm BHCSM3 x 10mm FHCSFT Ballstud Washer, aluminum(1mm, 2mm)M3 x 12mm BHCSHeavy-duty Ballstud, 6mmHeavy-duty Ballstud, 8mmTop Plate, B5Steering Set, B53x7x3 Ball Bearing
21173
25202
91048
5407
5407
91048
31286 9147591475
91475
91475
91475
9147591391
91391
91391
91391
91047
31286
25202
25189
89202
91362
8122020
4 ea.
1088118
:: Optional Gear Differential
:: Differential Fluids
467591461914629146391465
5450545154525453545454555456545754585459
61112
1111111111
M2.5 x 6 FHCSGear Diff Kit, B5Gear Diff Gear/Cover, B5Gear Diff Rebuild, B5Gear Diff Outdrives, B5
Silicone Diff Fluid 1,000CSTSilicone Diff Fluid 2,000CSTSilicone Diff Fluid 3,000CSTSilicone Diff Fluid 5,000CSTSilicone Diff Fluid 7,000CSTSilicone Diff Fluid 10,000CSTSilicone Diff Fluid 20,000CSTSilicone Diff Fluid 30,000CSTSilicone Diff Fluid 60,000CSTSilicone Diff Fluid 100,000CST
91465
91465
91465
91465
91465
91465
4675 91462
91462
91463
4675
9146591465
91465
:: Turnbuckles and Servo Mounts62637337918031286
315328900791047914439145391455
241
4 ea.
618214
Turnbuckle, 2.06”.250 x .125 x .015” WasherServo Horns, MoldedFT Ballstud Washer, aluminum(1mm, 2mm)M3 x 8 BHCSSteering Servo Ring, blueHeavy-duty Ballstud, 6mmServo Mount, B5HD Ball Cup Set (Small), B5Steering Link, B5
91455
7337
7337
7337
7337
91455
91455
31532
31532
91443
91443
31286
31532
31532
31532
31532
91047
89007
9180
6263
91453
91453
24
:: Rear Arm4670256163151089202910479114891394914129141491416914369143791438914399144191476
626
10881
Pr.Pr.1421122
M3 x 8mm Set ScrewBearing, 10 x 15 x 4M2 x 4mm BHCSM3 x 12mm BHCSHeavy-duty Ballstud, 6mmM4 Locknut, with flange and knurlHinge Pin Set, B5Rear Arms, B5Rear Hubs, B5Rear Hub Link Nut Set, B5CVA/Wheel Hex Pin, B5CVA Axle, B5CVA Rebuild Kit, B5CVA Bone, B5Wheel Hex (Rear), B56x13x5 Ball Bearing
4670
25616
31510
89202
91047
91414
91412
91436
91476
91441
91437
91438
91438
91439
91148
91394
91414
91416
9141491414
91414
Steering Block, Hex:: Front Arm46702518925215252373151031520315308920291047910499114891394913989140091402914049140691407
620202666
108881
Pr.Pr.4
Pr.22
M3 x 8mm Set ScrewM3 x 22mm BHCSM3 Locknut, blackBearing, 5 x 10 x 4M2 x 4mm BHCSM2.5 x 6mm BHCM3 x 5mm BHCSM3 x 12mm BHCSHeavy-duty Ballstud, 6mmHeavy-duty Ballstud, 10mmM4 Locknut, with flange and knurlHinge Pin Set, B5Front Arms, B5Caster Block, B5Caster Block Bushing, B5Steering Block, B5Front Axles, B5Front Axle Crush Tubes, B5
4670
25189
3151091394
91394
91398
91400
91400
91400
91402
91404
91404
91404
91407
31520
31530
25215
25215
89202
89202
91049
91047
31510
91148
25237
25237
91406
:: Battery Strap4689914569145891459
6121
M3 x 16mm Set ScrewComposite Battery Strap, B5Battery Strap Thumbwheel, B5Battery Spacers Set, B5
25
4689
91458
91458
91458
91456
91459
91459
91459
91458
4689
:: Front Shock Tower2561231286
892028920491049913739144591477
204 ea.
10108146
M3 Locknut, with flangeFT Ballstud Washer, aluminum(1mm, 2mm)M3 x 12mm BHCSM3 x 24mm BHCSHeavy-duty Ballstud, 10mmFront Tower, B5Shock Bushing (Composite), B5M3 Nut, Black
91049
9104931286
31286
25612
25612
91445
91445
91477
91477
91373
89204
89204
89202
89202
:: Rear Shock Tower211732518725201252042521125612892049137591433914459147791478
1220202020201011466
Small Body ClipsM3 x 14mm BHCSM3 x 8mm FHCSM3 x 16mm FHCSM3 x 10mm BHCSM3 Locknut, with flangeM3 x 24mm BHCSRear Tower, B5Wing/Rear Body Mounts, B5Shock Bushing Composite, B5M3 Nut, BlackM3 x 30mm BHCS
25211
25187
25187
25612
25612
2117325204
89204
91375
91433
91433
91433
91433
91478
91477
91477
91445
91445
8920425204
25201
2521121173
21173
26
:: Wheels9690969196959696
2222
Buggy Front Wheel, hex, white - KitBuggy Front Wheel, hex, yellowBuggy Rear Wheel Hex, white - KitBuggy Rear Wheel Hex, yellow 9696
9691
Not includedin Kit!
Not includedin Kit!
:: Chassis6338251872520325204252112522531286
31521315328920891049913609136491371913779137991380913829139491410
120202020204ea
66
108111111111
Antenna Tube & Cap (black)M3 x 14mm BHCSM3 x 12mm FHCSM3 x 16mm FHCSM3 x 10mm BHCSM3 x 3mm Set ScrewAluminum Ballstud Washer(1mm & 2mm) M2.5 x 8mm BHCSM3 x 8mm BHCSM3 x 14mm FHCSHeavy-duty Ballstud, 10mmChassis, B5Bulkhead (25° & 30°), B5Hinge Pin Bracem B5Chassis Brace, B5Chassis Plate, B5Receiver Mount, B5Arm Mount Set, B5Hinge Pin Set, B5Front Bumper, B5
31286
31286
91049
91049
25211
25211
91377
91380
31532
31532
25225
6338
6338
91360
25187
91394
91394
91382
91382
91379
89208
8920825203
25203
31521
91410
25204
25204
25204
25204
91364
9137131521
:: Factory Team and Option Parts140614091734173517367485748631286911759117691177911789117991363913729137491376913789138191382913839138591387913899139291395913999140191403914059140891409914139141591442914469144791450
9145791468914929149391495
915169152691527
Pr.Pr.1046
Pr.1
4ea.112111111111111111
Pr.Pr.
2ea.Pr.22
Pr.Pr.2442
11181
111
FT Ti Turnbuckle, 2.00” (blue)FT Ti Turnbuckle, 1” (sway bar) (blue)FT Blue Body Clip, 4 long, 6 shortFT Blue Body Clip, longFT Blue Body Clip, shortFT V2 Slipper HubsFT V2 Slipper Spring and WasherFT Ballstud Washer, aluminum (1mm, 2mm)FT VTS Slipper ConversionVTS Slipper HousingVTS Slipper PadsVTS Slipper PlateFT VTS Slipper Hub, outerTop Plate (HARD), B5Aluminum Front Pin Brace, B5Front Tower (HARD), B5Rear Tower (HARD), B5Chassis Brace (HARD), B5ESC Mount Graphite, B5Arm Mount Set, B5Aluminum Arm Mount (C), B5Arm Mount Inserts Set (C), B5Aluminum Arm Mount (D), B5Arm Mount Insert (D), B5Aluminum Steering Set, B5TiN Hinge Pin Set, B5Front Arms (HARD), B5Caster Block (HARD), B5 w/insertsCaster Block Bushing (Offset - long/short), B5Steering Block (HARD), B5Front Axle (Clamp Hex), B5 - Req. #91409Clamping Hex (Front), B5 - Req. #91408Rear Arms (HARD), B5Rear Hubs (HARD), B5 w/insertsClamping Hex (Rear), B5Shock Bushing (Aluminum), B5 - Req. #91447Shock Bushing Ball, B5 - Req. #9144612mm V2 Aluminum Shock Cap (2 screws, 2 bleeder gaskets, and 2 o-rings)Graphite Battery Strap, B5Anti-Roll Bar Kit, B512mm V2 Bleeder Gasket/ScrewFT Low Friction X-Rings12mm V2 X-Ring Rebuild Kit (4 clear x rings, 2 spacers, 4 hat bushings)RC10B5M Front TowerRC10B5M Front ArmRC10B5M Front Arm (HARD)
:: Body and Decals914709147191472
111
RC10B5 Clear BodyRC10B5 Clear WingRC10B5 Sticker Sheet
:: Reedy Accessories247248249250604606607609610643644645646647648650654655656658659660661663664669716961962974975978979980981982992
111111111111111
3ea.111111111211311111111
Sonic 540 Mach 2 Sensor w/bearingSonic 540 Mach 2 Steel Bearing SetSonic 540 Mach 2 Ceramic Bearing SetSonic 540 Mach 2 Insulator Set526-S AC/DC 2S-6S LiPo/LiFe ChargerCharge Harness 2S Saddle Pack 4mmCharge Harness 2S Standard Pack 4mmTAM to DEANS® charge adapter447-S AC/DC NiMH Peak ChargerLow-Profile Bullet Connector, 4mm x 14mm (2)Low-Profile Bullet Connector, 4mm x 14mm (10)Low-Profile Bullet Connector, 5mm x 14mm (2)Low-Profile Bullet Connector, 5mm x 14mm (10)Pro Silicone Wire, 12AWG BlackPro Silicone Wire, 14AWG BlackShrink Tubing (Yellow, Orange, Red, Blue, Black)4.0mm Bullet Plugs (2M, 2F) 4.0mm Bullet Plugs (2M, 10F) 4.0mm Bullet Plugs (10F)4.0mm Bullet Plugs (10M)4.0mm Bullet Plugs (30M)3.5mm Bullet Plugs (3M, 3F)3.5mm Bullet Plugs (10F)3.5mm Bullet Plugs (10M)3.5mm Bullet Plugs (30M)5mm Bullet ConnectorReedy 09 Decal SetSonic 540/550 Timing Cap with ScrewsSonic 540 Case Screws540-SL/550-SL Steel Bearing Set540-SL/550-SL Ceramic Bearing SetFlat Sensor Wire 70mmFlat Sensor Wire 110mmFlat Sensor Wire 150mmFlat Sensor Wire 200mmFlat Sensor Wire 270mmSonic 540 Rotor Spacers
27:: XP Electronics291072913329134291382913929140291412914229143291442914529146291662916729168292092921029211292122921429215292162925029251292522925329254
111111111111111111111111111
XP DS1903/S1903 Metal Gear SetXP DS1903 Digital ServoXP DS1903MG Digital ServoXP SC500-BL Brushless ESCXP SC900-BL Brushless ESCXP SC200 Brushed ESC XP SC450 Brushless ESCXP ESC Fan OptionXP SC700-BL Brushless ESCXP SC1200-BL Brushless ESCXP SC1300-BL Brushless ESCXP SC1300DB Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoXP DS1510MG Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313/DS1015Accessory Pack, DS1313/DS1015TRS403-SSi 2.4GHz 4Ch ReceiverXP2G 2.4GHz Radio SystemXP3G 2.4GHz Radio SystemXP DS1505 Digital ServoXP DS1505MG Digital ServoXP DS1505 Metal Gear SetXP DS1510 Metal Gear SetXPSSi Receiver Antenna
28
:: Reedy Motors and ESC’s
:: Reedy Batteries
228231232233233S234235236237238239240241242243244245246908920921922923941S954955956957958965966967983984985986987
1111111111111111111111111111111111111
302310314602632637737738
11111111
Sonic 540 Mach 2 25.5 Competition Brushless MotorSonic 540 Mach 2 21.5 Competition Brushless MotorSonic 540 Mach 2 17.5 Competition Brushless MotorSonic 540 Mach 2 13.5 Competition Brushless MotorSonic 540/540 Mach 2 Stator 13.5Sonic 540 Mach 2 10.5 Competition Brushless MotorSonic 540 Mach 2 9.5 Competition Brushless MotorSonic 540 Mach 2 8.5 Competition Brushless MotorSonic 540 Mach 2 8.0 Competition Brushless MotorSonic 540 Mach 2 7.5 Competition Brushless MotorSonic 540 Mach 2 7.0 Competition Brushless MotorSonic 540 Mach 2 6.5 Competition Brushless MotorSonic 540 Mach 2 6.0 Competition Brushless MotorSonic 540 Mach 2 5.5 Competition Brushless MotorSonic 540 Mach 2 5.0 Competition Brushless MotorSonic 540 Mach 2 4.5 Competition Brushless MotorSonic 540 Mach 2 4.0 Competition Brushless MotorSonic 540 Mach 2 3.5 Competition Brushless MotorReplacement Rotor 540-SL540-SL Brushless Motor 3300kV540-SL Brushless Motor 3900kV540-SL Brushless Motor 4900kV540-SL Brushless Motor 6100kVSonic 540/540 Mach 2 Stator 17.5Sonic 540 Stock Rotor 12.3 x 24.2 (7.25)Sonic 540 Stock Rotor 12.3 x 25.0 (7.25)Sonic 540 Stock Rotor 12.5 x 25.0 (7.25)Sonic 540 Modified Rotor 12.2 x 25.0 (5.0)Sonic 540 Modified Rotor 12.5 x 25.0 (5.0)Reedy 540-SL 3300kV/XP SC700-BL ESC ComboReedy 540-SL 3900kV/XP SC700-BL ESC ComboReedy 540-SL 4900kV/XP SC700-BL ESC ComboReedy 540-SL 3300kV/XP SC1200-BL ESC ComboReedy 540-SL 3900kV/XP SC1200-BL ESC ComboReedy 540-SL 4900kV/XP SC1200-BL ESC ComboReedy 540-SL 6100kV/XP SC1200-BL ESC ComboSonic 540 Modified Rotor 13.0 x 25.0 (5.0)
AA Alkaline 1.5V (4)LiPo 65C 5700mAh 7.4V SPLiPo 65C 6000mAh 7.4V SQLiPo 65C 4100mAh 7.4V ShortyLiPo TX Lightweight Battery 1350mAh 11.1VLiPo TX Battery - M11X 2500mAh 7.4VWolfpack LiPo 4800mAh 7.4V 25C S.P.Wolfpack LiPo 3800mAh 7.4V 25C Shorty
:: Lubes & Adhesives / Decals / Misc.1105159615976588659166366727
7163816382038349787
1111112
11121
FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, mediumBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape
Reedy 2009 Sticker SetAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo StickerFT Chassis Protective Sheet
:: 1/18 Kits and RTR’s2010320121
11
RC18B2 - RC18T2 Team KitSC18 RTR Brushless (ready-to-run)
:: Qualifier Series Vehicles7052201112011920510
30112
1111
1
Pro Lite 4x4 RTR, 1/10 Scale (ready-to-run)Rival Mini Monster Truck 1/18 Scale (ready-to-run)APEX Mini Touring RTRRIVAL Electric Monster Truck RTR, 1/8 Scale (ready-to-run)APEX Touring V-Type, 1/10 Scale (ready-to-run)
:: 1/12, 1/10 Kits and RTR’s402070257028C70307030C70387039704670497050705170547055709380208022904090419042905090623010130109900019000390005900069000890010
11111111111111111111111111111
RC12R5.2 Factory Team KitRC10T4.2 Factory Team KitSC10 Pro Comp RTR (ready-to-run) ComboSC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 KMC Wheels RTR (ready-to-run) ComboSC10.2 Factory Team KitRC10T4.2 RS RTR 2.4GHz Brushless (ready-to-run)SC10 RS RTR, Lucas Oil (ready-to-run)SC10 RS RTR, Rockstar/Makita (ready-to-run)SC10 RS RTR, Hart and Huntington (ready-to-run)SC10 RS RTR, Lucas Slick Mist® BodySC10 RS RTR, Toyota Racing/TRDSC10 RS RTR, Monster Energy ToyotaSC10GT RTR (ready-to-run)RC10R5 Factory Team KitRC10R5.1 Factory Team KitRC10B4.1 Worlds KitRC10B4.2 Factory Team KitRC10B4.2 RS RTR 2.4GHz Brushless (ready-to-run)SC10B RS RTR (ready-to-run)RC10B44.2 Factory Team 4WD Buggy KitTC4 Club Racer 4WD Touring Car Race RollerRC10TC6.2 Factory Team 4WD Touring Car KitRC10B5 Team KitRC10B5M Team KitSC10 4x4 Lucas Oil RTR (ready-to-run)SC10 4x4 Pro Comp RTR (ready-to-run)Limited Edition SC10 4x4 RTR Monster EnergySC10 4x4 Factory Team Kit
29:: RePlay CamerasRP001RP002RP021RP022RP023RP024RP029RP030RP032RP033RP034RP036RP038RP041RP042RP043RP044RP045RP046RP047RP048RP049RP054
11111111111111111111111
Replay XD1080 Complete Camera SystemReplay XD720 Complete Camera SystemReplay XD1080 Lens Bezel KitReplay XD1080 Clear Lens CoverReplay XD1080 Lens Bezel & Rear Cap O-RingReplay XD Lens BezelReplay XD1080 HDMI to Mini-HDMIReplay XD1080 Mini 8-pin USB Charge Data CableUSB DC Car Charger 1A StubbyUSB DC Car Charger 500mAhMicro SDHC USB Reader3M VHB 4991 Mount Adhesive for SnapTray3M VHB 5962 Mount Adhesive for SnapTrayReplay XD Suction Cup Arm Mini ClampReplay XD Suction Cup Short Arm BaseReplay XD Skateboard MountReplay XD VHB SnapTray, ConvexReplay XD VHB SnapTray, FlatAu Plug for Universal DC Wall ChargerEu Plug for Universal DC Wall Charger Uk Plug for Universal DC Wall ChargerUniversal USB DC Wall Charger 1AReplay ReView Field Monitor
:: Tools111111131449154115421543154415451546154715481553155415611562156315641565156715891590159216551656165716581659166016611662166316641665166616671668166916701671167216731674
1719173737183719372039876429695674947709
111111111111111111111111111111111111111111
11121212111112
FT Turnbuckle Wrench12mm Big Bore Shock ToolFT Off Road Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT 8-Piece 1/4” Hex Drive SetFT 1/4” Hex Drive Handle, without tipsFT 1/4” Hex Drive .050” TipFT 1/4” Hex Drive 1/16” TipFT 1/4” Hex Drive 5/64” - 2.0mm TipFT 1/4” Hex Drive 3/32” TipFT 1/4” Hex Drive 1.5mm TipFT 1/4” Hex Drive 2.5mm TipFT 1/4” Hex Drive 3/16” Nut Driver TipFT 1/4” Hex Drive 1/4” Nut Driver TipFT 1/4” Hex Drive 11/32” Nut Driver TipFT 1/4” Hex Drive 5.5mm Nut Driver TipFT 1/4” Hex Drive 7.0mm Nut Driver TipFT 1/4” Hex Drive 8.0mm Nut Driver TipFT 1/4” Hex Drive 5/64” - 2.0mm Ball End TipFT 1/4” Hex Drive 3/32” Ball End TipFT 1/4” Hex Drive Standard Screwdriver TipFT 1/4” Hex Drive Phillips Screwdriver TipFT 1/4” Hex Drive 2.5mm Ball End TipFT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesComposite Droop GaugeShock Building ToolMolded Tools, SetV2 Stamped Multi-tool4 Inch Nylon Wire Ties
:: Notes
:: ApparelSP31**SP32**SP37**SP38SP39
SP71**SP77**SP78**SP79**SP84**SP86**SP90**SP91**SP92**SP93**SP94**SP95**SP96**SP97**SP98**SP416SP417
SP420**SP421SSP421LSP422SSP422LSP423SSP423LSP424SSP424L
715110684
1111111111111111111111
Pr.1111111111
27 Time WC T-Shirt, Black (S, M, L, XL, 2XL, 3XL)Kids AE 2012 T-Shirt, Blue (S, M, L)Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL)Reedy Trucker HatReedy PatchAssociated Winter Jacket (M, L, XL)AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL)AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL)AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL)Reedy 3D T-Shirt, Black (S, M, L, XL, 2XL, 3XL)Reedy Womens 3D T-Shirt, Black (S, M, L, XL)AE Retro T-Shirt, Blue (S, M, L, XL, 2-5XL)AE Retro T-Shirt, Black (S, M, L, XL, 2-5XL)AE Retro T-Shirt, White (S, M, L, XL, 2-5XL)2013 Worlds T-Shirt, Blue (S, M, L, XL, 2-5XL)2013 Worlds T-Shirt, Black (S, M, L, XL, 2-5XL)2013 Worlds Hoodie, Black (S, M, L, XL, 2-3XL)AE Retro Womens T-Shirt, Pink (S, M, L, XL)AE Retro Womens T-Shirt, Black (S, M, L, XL)AE Womens T-Shirt, Black (S, M, L, XL)Associated Car Carrier Bag, Medium1/10 FT Motor BagAE Pit Gloves (L, XL)AE 2012 Hat, Black, Flat Bill, S/MAE 2012 Hat, Black, Flat Bill, L/XLAE 2012 Hat, Black, Curved Bill, S/MAE 2012 Hat, Black, Curved Bill, L/XLAE 2012 Hat, White, Flat Bill, S/MAE 2012 Hat, White, Flat Bill, L/XLAE 2012 Hat, White, Curved Bill, S/MAE 2012 Hat, White, Curved Bill, L/XLReedy 2009 Track BannerTeam Associated Track Banner
** Use part number plus the desired size when ordering!
:: 1/8 Kits and RTR’s205012050220503
20504
809068090780908809098091280933
80934
111
1
111111
1
MGT 4.60 SE RTR (ready-to-run)MGT 8.0 Nitro RTR (ready-to-run)Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)RC8.2 Nitro Buggy Factory Team KitRC8.2e Electric Buggy Factory Team KitRC8.2e Electric Buggy RTR (ready-to-run)RC8.2RS Nitro Buggy RTR (ready-to-run)RC8T Championship EditionSC8.2e Short Course Race Truck, Rockstar/Makita Electric RTR (ready-to-run)SC8.2e Short Course Race Truck, Slick Mist ElectricRTR (ready-to-run)
30:: Notes
:: Contact Information
Associated Electrics, Inc.26021 Commercentre Drive
Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com
http://www.RC10.comhttp://twitter/Team Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500fax: (949) 544-7501
Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
Driver: Date: Track: Event:Setup Sheet
Size:Surfaces:Traction:Moisture:Condition:
Temperature:Notes:
:: For more setups, visit RC10.com and click on “Setup Sheets”
A
A
B
B
3 21
12
Ball StudSpacing:
Front Suspension:
Rear Suspension:
Electronics:
Track Info:
Race Results:
Drivetrain:
Tires:
Body & Wing:
Vehicle Comments:
Shocks:
Anti Roll Bar:NoneBlack (1.2mm)Silver (1.3mm)Gold (1.4mm)
Radio: Servo:EPA: Throttle: % Brake: %ESC:ESC Settings:Motor: Wind: Timing:Pinion: Spur:Battery:Battery Position:
Camber: °Ride Height:Hub Spacing:
Notes:
Camber: °Total Toe: °Ride Height: Arm Type:Tower Type:Caster Block Insert: °Kick-Up Angle: °
Notes:
Differential:Ball: Setting:Gear: Oil:
Piston:Oil:Spring:Limiters:Cup Offset:Stroke:Free Length:Notes:
Total Vehicle Weight:
Qualify: Main:Finish: TQ:Best Lap Time:
Small
Low
Bumpy
DryHard PackedIndoor
Ambient: Track:
DirtMedium
Medium
Grooved
Damp
SmoothOutdoor
CarpetLarge
High
DustyWet
Loamy
Astroturf Multi SurfaceVery High
Extra Large Tires (F/R):Compound (F/R): Insert (F/R):Wheel (F/R):Notes:
Body: Wing:Wing Angle: 0° 3° 6°Notes:
Front
////
Rear
FreeLength
Stroke
AB
Slipper Clutch:
Type:# of Pads:Notes:
Stroke
321
12
Ball StudSpacing:
Hub Insert:0° 0.5° 1°
Caster Block Spacing:
Steering Stop
Spacing:
Ball StudSpacing:Bump Steer
Spacing:
0
Team Kit Stock Setup
0
02mm
-1
-1
0
525
24mm
24mm
3+2
StandardStandard
2mm
2mm
Trailing Axle Insert:
2mm 3mm 4mm
Axle Height: Up Middle Down
Rear Hub Link Setting:Up
Up
Down
Down
A
B
C
B
B
A
A
Forward Middle Back
Arm Mount:Inboard Toe: °Anti-Squat:
1/4 Turn Out
RC10B5 BodyRC10B5 Wing
VTS
1.6
2mm
30 wtGreen
35mm
1.730 wtWhite
25mm
3
32:: Hardware - 1:1 Scale View
Notes:
E-clip 1/8 (6299)
Clips
5/64 Diff Thrust Balls (6574)
3/32 Carbide Diff Balls (6581)
Diff Balls
Servo Mount Washer (7337)(.250 x .125 x .815)
FT Ballstud Washer, Aluminum(1mm and 2mm, 4 each) (31286)
Shims and Washers
Ballstuds
HD 6mm (91047)Ti Nitride HD 6mm (91118)
HD 8mm (91048)Ti Nitride HD 8mm (91119)
HD 10mm (91049)Ti Nitride HD 10mm (91120)
HD 12mm (91050)Ti Nitride HD 12mm (91121)
3x8mm (25201)3x8mm Aluminum (8553)
3x10mm (25202)
3x12mm (25203)
3x14mm (89208)
3x16mm (25204)
Flat Head (fhcs)
M3 Nut (91477)M3 Alum. Locknut, Blue (31550)
M3 Locknut w/Flange (25612) FT 3mm Locknuts, Blue(25392)
M4 Locknut w/Flange (91148) FT M4 Locknuts w/Flange,
Blue (31551)
Nuts (lock/plain)
2x4mm (31510)
2.5x6mm (31520)
2.5x8mm (31521)
3x4mm (91158)
3x5mm (31530)
3x6mm (31531)
3x8mm (31532)3x8mm Aluminum (8552)
3x10mm (25211)
3x12mm (89202)
3x14mm (25187)
3x16mm (89203)
3x18mm (2308)
3x22mm (25189)
3x24mm (89204)
3x30mm (91478)
Button Head (bhcs) Ball Bearings
3x7x3mm (91475)
5x8mm (31400)
5x10x4mm (25237)
6x12x4mm (25238)
6x13x5 (91476)
10x15x4 (25616)
3x3mm (25225)
3x8mm (4670)
3x16mm (4689)
Set Screws
Driver: Date: Track: Event:Setup Sheet
Size:Surfaces:Traction:Moisture:Condition:
Temperature:Notes:
:: For more setups, visit RC10.com and click on “Setup Sheets”
A
A
B
B
3 21
12
Ball StudSpacing:
Front Suspension:
Rear Suspension:
Electronics:
Track Info:
Race Results:
Drivetrain:
Tires:
Body & Wing:
Vehicle Comments:
Shocks:
Anti Roll Bar:NoneBlack (1.2mm)Silver (1.3mm)Gold (1.4mm)
Radio: Servo:EPA: Throttle: % Brake: %ESC:ESC Settings:Motor: Wind: Timing:Pinion: Spur:Battery:Battery Position:
Camber: °Ride Height:Hub Spacing:
Notes:
Camber: °Total Toe: °Ride Height: Arm Type:Tower Type:Caster Block Insert: °Kick-Up Angle: °
Notes:
Differential:Ball: Setting:Gear: Oil:
Piston:Oil:Spring:Limiters:Cup Offset:Stroke:Free Length:Notes:
Total Vehicle Weight:
Qualify: Main:Finish: TQ:Best Lap Time:
Small
Low
Bumpy
DryHard PackedIndoor
Ambient: Track:
DirtMedium
Medium
Grooved
Damp
SmoothOutdoor
CarpetLarge
High
DustyWet
Loamy
Astroturf Multi SurfaceVery High
Extra Large Tires (F/R):Compound (F/R): Insert (F/R):Wheel (F/R):Notes:
Body: Wing:Wing Angle: 0° 3° 6°Notes:
Front
////
Rear
FreeLength
Stroke
AB
Slipper Clutch:
Type:# of Pads:Notes:
Stroke
321
12
Ball StudSpacing:
Hub Insert:0° 0.5° 1°
Caster Block Spacing:
Steering Stop
Spacing:
Ball StudSpacing:Bump Steer
Spacing:
Trailing Axle Insert:
2mm 3mm 4mm
Axle Height: Up Middle Down
Rear Hub Link Setting:Up
Up
Down
Down
A
B
C
B
B
A
A
Forward Middle Back
Arm Mount:Inboard Toe: °Anti-Squat:
Associated Electrics, Inc.26021 Com
mercentre Dr.
Lake Forest, CA 92630 USAhttp://w
ww
.TeamAssociated.com
http://ww
w.RC10.com
http://twitter/Team
_Associatedhttp://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501Check out the follow
ing web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
ww
w.Team
Associated.com. - w
ww
.RC10.com