KILLARK LIGHTING H A Z L O C H A Z L O C L I G H T I N G L I G H T I N G WWW.HUBBELL-KILLARK.COM L164 EZ SERIES MOGUL BASE HID FIXTURES Applications HOSTILELITE ® EZ Series mogul base fixtures are designed for installations where moisture, dirt, dust, corrosion and vibration may be present, or NEMA 3 and 4x areas where wind, water, snow or high ambients can be expected. They can be used in locations made hazardous due to the presence of flammable or explosive gases, vapors and combustible dusts as defined by the NEC. Typical applications include classified areas such as paint manufacturing plants, ammunition facilities, oil and gas producing and refining plants, off-shore and dockside installations, tank farms, pipeline pumping stations and marine loading and fuel transfer terminals. Features • Three light sources – High Pressure Sodium (50-400W), Metal Halide (70-400W) and Pulse Start Metal Halide (175-400W) • HOSTILELITE ® EZ fixtures are now available with Pulse Start Metal Halide ballasts • Mounting choice –Pendant, ceiling, 25˚ stanchion or 90˚ wall mount, all with “wireless” design that allows fast, easy fixture installation or removal for maintenance. See pages L181-182 for trunnion mounted fixtures • Factory sealed – No external seal needed. Simply wire mounting cap and thread on fixture to install • Corrosion resistant – Copper-free aluminum die cast construction. Baked powder epoxy finish, electrostatically applied. Exposed hardware is 316 grade stainless steel • Accessories – Available with or without guard, standard dome or angle reflector • Options – EZ Series fixtures can be specified with instant restart for HPS lamps, auxiliary quartz circuit, ballast protector, and fuse kits. (See page L156 for details) Catalog Number Logic Series Constant Lamp Type S—High Pressure Sodium H—Metal Halide P—Pulse Start Metal Halide Lamp Wattage 05—50 Watt HPS 07—70 Watt HPS/MH 10—100 Watt HPS/MH 15—150 Watt HPS/MHP 17—175 Watt MH/MHPk 20—200 Watt HPS/MHP 25—250 Watt HPS/MH/MHPk 32—320 Watt MHP 35—350 Watt MHP 40—400 Watt HPS/MH/MHPk Voltage 0—Quadri-Volt, 60 Hz. (120, 208, 240, 277) 5—480 Volts, 60 Hz. 6—TriTap Canada (120, 277, 347), 60 Hz. 7—220V, 60Hz 8—220/240 Volt, 50 Hz. Options Q—Auxiliary Quartz Standbyl R—Instant Restrikel(150W HPS Max) BP—Ballast Protector PS—Paint Spray (50, 70, 100W HPS, 70, 100, MH) EB—Eyeboltsj SU103—Assembled w/Lamp LS—Standard Lamp Supplied LD—Dual Arc Tube LampSupplied for 70, 100, 150 HPS only Guard G—Omit G if guard is not required Reflector S—VM Fiberglass Dome Reflector A—VM Fiberglass Angle Reflector D—Deep White Reflector Z—Deep Alzak Reflector EZ 0 00 0 00 0 0 - 00 (CEN*) Compliances • UL-844 Electric Lighting Fixtures for use in Hazardous Locations • UL Marine Type Electric Lighting Fixtures • UL-1598 Standard for HID Lighting Fixtures • CSA C22.2 no. 137-M1981 Electric Luminaires for use in Hazardous Locations • CSA C22.2 no. 94-1976 Special purpose enclosure • NEMA 3, 4, 4x, 7CD, 9EFG *CEN (CENELEC) Approved option available on some models. See page L160 for more information. j Two eyebolts plus 12” of connecting chain included. k 175,250 and 400W MH EXPORT ONLY (EISA LAW). l Not for use with DUAL-ARC-TUBE Lamps. Consult factory for available lamp and voltage combinations. HOSTILELITE ® EZ fixtures are now available with Pulse Start Metal Halide ballasts. Pulse Start systems provide higher and better maintained light output with longer life compared standard metal halide systems. Pulse start and standard Metal Halide lamps and ballasts are not interchangeable. V V Class I, Div. 1 & 2 Groups C,D Class l, Zone 1 & 2, Groups llB,llA Class l, Zone 1, AEx d IIB Class II, Div. 1 & 2, Groups E,F,G Class III, Div. 1 & 2 Suitable for wet locations Marine Rated (US Only) NEMA 3, 4, 4X Factory Sealed - File E10514 and E91793 Certified - File LR11713 FEATURES-SPECIFICATIONS Mounting Type A2—3/4” Pendant A3—1” Pendant X2—3/4” Ceiling X3—1” Ceiling B2—3/4” Bracket B3—1” Bracket D4—1-1/4”/1-1/2” Stanchion
Transcript
KILLARK LIGHTING
H A Z LO C
H A Z LO C
LIGHTING
LIGHTING
WWW.HUBBELL-KILLARK.COML164
EZ SERIES
MOGUL BASE HID FIXTURES
Applications
HOSTILELITE® EZ Series mogul base fixtures are designed for installations where moisture, dirt, dust, corrosion and vibration may be present, or NEMA 3 and 4x areas where wind, water, snow or high ambients can be expected. They can be used in locations made hazardous due to the presence of flammable or explosive gases, vapors and combustible dusts as defined by the NEC.
Typical applications include classified areas such as paint manufacturing plants, ammunition facilities, oil and gas producing and refining plants, off-shore and dockside installations, tank farms, pipeline pumping stations and marine loading and fuel transfer terminals.
Features
• Three light sources – High Pressure Sodium (50-400W), Metal Halide (70-400W) and Pulse Start Metal Halide (175-400W)
• HOSTILELITE® EZ fixtures are now available with Pulse Start Metal Halide ballasts
• Mounting choice –Pendant, ceiling, 25˚ stanchion or 90˚ wall mount, all with “wireless” design that allows fast, easy fixture installation or removal for maintenance. See pages L181-182 for trunnion mounted fixtures
• Factory sealed – No external seal needed. Simply wire mounting cap and thread on fixture to install
• Accessories – Available with or without guard, standard dome or angle reflector
• Options – EZ Series fixtures can be specified with instant restart for HPS lamps, auxiliary quartz circuit, ballast protector, and fuse kits. (See page L156 for details)
Catalog Number Logic
Series Constant
Lamp TypeS—High Pressure SodiumH—Metal HalideP—Pulse Start Metal Halide
EB—EyeboltsjSU103—Assembled w/LampLS—Standard Lamp SuppliedLD—Dual Arc Tube LampSupplied for 70, 100, 150 HPS only
GuardG— Omit G if guard is not requiredReflectorS—VM Fiberglass Dome ReflectorA—VM Fiberglass Angle ReflectorD—Deep White ReflectorZ—Deep Alzak Reflector
EZ 0 00 0 00 0 0 - 00 (CEN*)
Compliances
• UL-844 Electric Lighting Fixtures for use in Hazardous Locations
• UL Marine Type Electric Lighting Fixtures• UL-1598 Standard for HID Lighting Fixtures• CSA C22.2 no. 137-M1981 Electric
Luminaires for use in Hazardous Locations• CSA C22.2 no. 94-1976 Special
purpose enclosure• NEMA 3, 4, 4x, 7CD, 9EFG
*CEN (CENELEC) Approved option available on some models. See page L160 for more information.j Two eyebolts plus 12” of connecting chain included. k 175,250 and 400W MH EXPORT ONLY (EISA LAW).l Not for use with DUAL-ARC-TUBE Lamps. Consult factory for available lamp and voltage combinations.
HOSTILELITE® EZ fixtures are now available with Pulse Start Metal Halide ballasts. Pulse Start systems provide higher and better maintained light output with longer life compared standard metal halide systems. Pulse start and standard Metal Halide lamps and ballasts are not interchangeable.
V
V
Class I, Div. 1 & 2 Groups C,DClass l, Zone 1 & 2, Groups llB,llAClass l, Zone 1, AEx d IIBClass II, Div. 1 & 2, Groups E,F,GClass III, Div. 1 & 2Suitable for wet locationsMarine Rated (US Only)NEMA 3, 4, 4XFactory Sealed
SEE WWW.HUBBELL-KILLARK.COM LIGHTING SOFTWARE FOR LATEST LED PHOTOMETRY L165
EZ SERIES
HIGH PRESSURE SODIUM 50-400W MOGUL BASE HID
j See Hazardous Location Application Data on pages L160 - L161 for specific suitabilities.k For 1 inch pendant, ceiling and wall hubs, substitute “3” for “2” in catalog number; example: EZS070A3G.l Stanchion conduit hub size supplied is 1-1/2” with 1-1/2” to 1-1/4” reducer for 1-1/4” mounting. (Refer to catalog logic).m Luminaire catalog numbers include guards. To order luminaire without guard, omit last letter “G” from catalog number.NOTE: Reflectors must be ordered separately (see page L157).All luminaires are designed for mounting with lamp in base up position.
Pendant Ceiling Wall Stanchion
Class I, Div. 1 & 2 Groups C,DClass l, Zone 1 & 2, Groups llB,llAClass l, Zone 1, AEx d IIBClass II, Div. 1 & 2, Groups E,F,GClass III, Div. 1 & 2Suitable for wet locationsMarine Rated (US Only)NEMA 3, 4, 4XFactory Sealed
FEATURES-SPECIFICATIONS- F i l e E10 514 a n d E 9 17 9 3 ( M a r i n e)
C e r t i f i e d - F i l e L R 117 13
EZ 50- 400 WATT, HIGH PRESSURE SODIUM jm
WATTS ANSI LAMP VOLTAGE @ 60HZ
CATALOG NUMBERPENDANT 3/4” k CEILING 3/4” k WALL 3/4” k STANCHION 1-1/4” l
Class I, Div. 1 & 2 Groups C,DClass l, Zone 1 & 2, Groups llB,llAClass l, Zone 1, AEx d IIBClass II, Div. 1 & 2, Groups E,F,GClass III, Div. 1 & 2Suitable for wet locationsMarineNEMA 3, 4, 4XFactory Sealed
j See Hazardous Location Application Data on pages L160 - L161 for specific suitabilities.k For 1 inch pendant, ceiling and wall hubs, substitute “3” for “2” in catalog number; example: EZH070A3G.l Stanchion conduit hub size supplied is 1-1/2” with 1-1/2” to 1-1/4” reducer for 1-1/4” mounting. (Refer to catalog logic).m Luminaire catalog numbers include guards. To order luminaire without guard, omit last letter “G” from catalog number.n Will also operate 150W M107 Metal Halide Lamps.o 175, 250, 400W MH EXPORT ONLY (EISA LAW).NOTE: Reflectors must be ordered separately (see page L157).All luminaires are designed for mounting with lamp in base up position.
Pendant Ceiling Wall Stanchion
EZ 70 - 400 WATT, METAL HALIDE jmo
WATTS ANSI LAMP VOLTAGE @ 60HZ
CATALOG NUMBERPENDANT 3/4” k CEILING 3/4” k WALL 3/4” k STANCHION 1-1/4” l
70 o M-98120, 208, 240, 277 EZH070A2G EZH070X2G EZH070B2G EZH070D4G
SEE WWW.HUBBELL-KILLARK.COM LIGHTING SOFTWARE FOR LATEST LED PHOTOMETRY L167
EZ SERIES
PULSE START METAL HALIDE 150-400W MOGUL BASE HID
Pendant Ceiling Wall Stanchion
ORDERING INFORMATION
j See Hazardous Location Application Data on pages L160 - L161 for specific suitabilities.k For 1 inch pendant, ceiling and wall hubs, substitute “3” for “2” in catalog number; example: EZP170A3G.l Stanchion conduit hub size supplied is 1-1/2” with 1-1/2” to 1-1/4” reducer for 1-1/4” mounting. (Refer to catalog logic).m Luminaire catalog numbers include guards. To order luminaire without guard, omit last letter “G” from catalog number.NOTE: Reflectors must be ordered separately (see page L157). All luminaires are designed for mounting with lamp in base up position.
EZ 150 - 400 WATT, PULSE START METAL HALIDE jmo
WATTS ANSI LAMP VOLTAGE @ 60HZ
CATALOG NUMBERPENDANT 3/4” k CEILING 3/4”k WALL 3/4” k STANCHION 1-1/4” l
Class I, Div. 1 & 2 Groups C,DClass l, Zone 1 & 2, Groups llB,llAClass l, Zone 1, AEx d IIBClass II, Div. 1 & 2, Groups E,F,GClass III, Div. 1 & 2Suitable for wet locationsMarineNEMA 3, 4, 4XFactory Sealed
Factory installed special ignitor provides hot lamp instant restart of HPS lamps after power interruption of up to 1 minute. Available for 50, 70, 100 and 150 watt HPS lamps only. Add suffix “R” to fixture catalog number (50/60 Hz).
Quartz Emergency Lamp
Factory installed special auxiliary quartz relay and D.C. bayonet base socket installed to accept 100 watt, 120 volt quartz (100Q/DC) lamps only. Lamps not supplied. Refer to Hazardous Location Application Data chart to verify suitability. Add suffix “Q” to fixture catalog number.
Ballast Protection Cutout
Optional factory installed special ballast protector replaces the standard HPS ignitor and applies starting pulse to the lamp for 10 to 15 seconds each time voltage is supplied to the ballast. If the lamp has not ignited by the end of the time period, the starter will cease pulsing. Used to eliminate the continuous high voltage pulsing of the ignitor when end of life, lamp cycling, or missing lamp conditions exist. Available for 70, 100, 150, 250 and 400 watt HPS fixtures. Add suffix “BP” to fixture catalog number.
25° Stanchion
Replacement Globe & Support Assemblies
Wall Bracket
Mounting Boxes
EACjPendant Ceiling
Notes: BP & R cannot be used together. Q & R cannot be used together.
* Supplied as 1-1/2” NPT with 1-1/2” x 1-1/4” reducer** 25 cu. in. below EZTB tangs.
FACTORY SEALEDClass I, DIV. 1 BCDClass II, DIV. 1&2 EFGCLASS IIINEMA 3, 4X IP66*40˚C ambient T3 Rated
EZCUP Close up plug for EZ mounting boxes. Used for maintenance when fixture is removed for service.
HIC-BEIGE replacement wiring plug for EZBx Wall Bracket
MOUNTING BOXESHUBSIZE
CATALOG NUMBERPENDANT CEILING BRACKET STANCHION
3/4” EZA2 EZX2** EZB2 —1” EZA3 EZX3 EZB3 —
1-1/4” / 1-1/2” — — — EZD4*
REPLACEMENT GLOBE & GLOBE SUPPORT ASSEMBLY
SERIES LAMP TYPE WATTAGE CATALOG NUMBER
EZS HPS 50-150EZGS1EZH MH 70-250
EZP MHP 150, 175, 250EZS HPS 250, 400
EZGS2EZH MH 400EZP MHP 320-400
PHOTO CELL FIELD KITS WITH HKB - GL BOX AND COVER
VMHKPC1 120VAC208-277VAC
347VACVMHKPC2VMHKPC3
KILLARK LIGHTING
H A Z LO C H A Z LO C
LIGHTING
LIGHTING
SEE WWW.HUBBELL-KILLARK.COM LIGHTING SOFTWARE FOR LATEST LED PHOTOMETRY L169
EZ SERIES
COMPONENT PARTS/ACCESSORIES
VMPSD40
VMPA40 HRD400HRD400ALZ (pictured)
EZTB
EZCB EZMO
EZG1 VMAG40S
k For clearance, wall mount models require standoff of 1/2” if not bottom feed; 1-1/2” if bottom feed.
j For VMAG40S with bottom closure order part number VMAG40SBC.
VMAGBCBottom Closure for
VMAG25S or VMAG40Sj
GUARDSCATALOG NUMBER SERIES LAMP TYPE WATTAGE DESCRIPTION
Notes for Class I, II, III Application Data Tables.j Instant restrike limited to 55°C ambient maximum.k Temperature code ID marked with an asterisk on Class ll table are listed for simultaneous use in Class I, Groups C,
D, and Class II, Groups E, F, G or Groups E, F.l Fixtures marked “N/A” not suitable for Class ll applications when supplied with auxiliary quartz.m See Class II table for fixtures suitable for locations having deposits of readily combustible paint residue (paint
spray booths). Do not install where marked operating temperature exceeds ignition temperature of hazardous atmosphere.
CEN Options
Applications
Killark EZ series fixtures are available with a European “Certificate of Conformity” from PTB (Physikalisch-Technische Bundesanstalt), the approval agency based in Germany. Fixtures with this rating will be useful for Original Equipment Manufacturers and others who build and ship apparatus into European markets.
This approval is granted by PTB with the use of a special ground lug and label. Fixtures carrying an EEx d llB approval are automatically granted an IP54 (ingress protection) rating. See Temperature Code chart below for PTB certified ratings. Killark EZ fixtures with the PTB rating and labels still carry all UL & CSA ratings.
Fixture housing/globe/globe support assemblies (e.g. EMS050 CEN) may be ordered with the CEN suffix. Complete fixture numbers, with the CEN suffix, will be shipped with the mounting boxes, guards and accessories as component parts. Reflectors and other accessory parts, as listed on page L157, may be used. Killark fixtures are NPT tapped and plugged with at least one conduit hole open.
Compliances• EN 50014:1992
• EN 50018:1994
EEx d IIB T6 (or T5-T2)PTB No. Ex-98.E.1076
EZ HAZARDOUS LOCATION DATA—CLASS I, DIVISIONS 1 & 2 jkm
LAMP RATED AMBIENT
°C
SUPPLY WIRE
SUITABLE FOR °C MIN.
CLASS I, DIVISIONS 1 & 2 MAXIMUM SURFACE TEMPERATURE
SEE WWW.HUBBELL-KILLARK.COM LIGHTING SOFTWARE FOR LATEST LED PHOTOMETRY L173
EZ SERIES
CLASS II/III APPLICATION DATA FOR HAZARDOUS LOCATIONS
Notes for Class I, II, III Application Data Tables.j Instant restrike limited to 55°C ambient maximum.k Temperature code ID marked with an asterisk on Class ll table are listed for simultaneous use in Class I, Groups C, D, and Class II, Groups E, F, G or Groups E, F.l Fixtures marked “NO” or “N/A” are not suitable for Class ll or II applications when supplied with auxiliary quartz.m Suitability for locations having deposits of readily combustible paint residue (paint spray booths). Do not install where marked operating temperature exceeds ignition temperature of hazardous atmosphere.
*
EZ HAZARDOUS LOCATION DATAJ– CLASS II & III , DIVISIONS 1 & 2jk
LAMP RATED AMBIENT
°C
SUPPLY WIRE
SUITABLE FOR C°
CLASS II, DIV. 1 & 2, MAX. SURFACE TEMP. UL/CSA SUITABILITY CLASS III, DIV. 1 & 2
UL/CSA SUITABILITY UL-595 MARINE
U.L. PAINT SPRAY
SUITABILITYm
UL/CSA TYPE 3
(RAINTIGHT)
UL/CSA TYPE 4
(HOSEDOWN)LAMP TEMP. I.D. W/O QTZ.
TEMP. I.D. WITH QTZl
GROUPSW/O QTZ. WITH QTZL W/O QTZ.WITH QTZ. l
EZS HPS 5040 85 55
85 85
T3B*
T3C* T3C* N/A
T3B* N/A
E,F,G
E,F E,F,G
E,F,G N/A N/A
YES YES YES NO YES NO
YES YES YES
YES NO NO
YES YES YES
YES YES YES
EZS HPS 7085 55 65
T3C* 85 85
T3B* T3C* T3B*
E,F,G N/A N/A
E,F,G E,F,G
E,F,G N/A N/A
YES NO YES NO YES YES
YES YES YES
YES NO NO
YES YES YES
YES YES YES
EZS HPS 10040 55 65
85 85 85
T3C* T3C* T3B
T3B* N/A N/A
E,F,G E,F,G E,F,G
E,F,G N/A N/A
YES NO YES NO YES YES
YES YES YES
YES NO NO
YES YES YES
YES YES YES
EZS HPS 15040 55 65
85 85 85
T3C* T3C* T3B*
T3B* N/A N/A
E,F,G E,F,
E,F,G
E,F,G N/A N/A
YES YES YES YES YES YES
YES YES YES
NO NO NO
YES YES YES
YES YES YES
EZS HPS 250 40 85 T3 T3 E,F E,F NO NO YES NO YES YESEZS HPS 400 40 85 N/A N/A N/A N/A NO NO YES NO YES YES
EZH MH 7040 55 65
85 85 85
T4A T4
T3C
N/A N/A N/A
E,F, E,F,G E,F,
N/A N/A N/A
YES NO YES NO YES NO
YES YES YES
YES NO NO
YES YES YES
YES YES YES
EZH MH 10040 55 65
85 85 85
T4A T4
T3C
N/A N/A N/A
E,F,G E,F,G E,F,G
N/A N/A N/A
YES NO YES NO YES NO
YES YES YES
YES NO NO
YES YES YES
YES YES YES
EZH MH 175 40 55
85 85
T3C* T3C*
T3A* N/A
E,F,G E,F,G
N/A N/A
YES NO YES NO
YES YES
NO NO
YES YES
YES YES
EZH MH 250 40 85 N/A N/A N/A N/A NO NO YES NO YES YESEZH MH 400 40 85 N/A N/A N/A N/A NO NO YES NO YES YES
EZP MHP 150 or 175
40 55
85 85
T3C* T3C*
T3A* N/A
E,F,G E,F,G
EF N/A
YES NO YES NO
YES YES
NO NO
YES YES
YES YES
EZP MHP 250 40 85 N/A N/A N/A N/A NO NO YES NO YES YESEZP MHP 320,350 40 85 N/A N/A N/A N/A NO NO YES NO YES YESEZP MHP 400 40 85 N/A N/A N/A N/A NO NO YES NO YES YES
